TOSIBOX connection to PLC and Operator panel KI

Transcription

1 TOSIBOX connection to PLC and Operator panel KI Function and area of use This document describes how to build up a connection from PC with Tosibox Key via internet, Tosibox Lock to PLC or operator panel. 2 About this Start Up document Copyright Beijer Electronics, 2014 This documentation (below referred to as the material ) is the property of Beijer Electronics. The holder or user has a non-exclusive right to use the material. The holder is not allowed to distribute the material to anyone outside his/her organization except in cases where the material is part of a system that is supplied by the holder to his/her customer. The material may only be used with products or software supplied by Beijer Electronics. Beijer Electronics assumes no responsibility for any defects in the material, or for any consequences that might arise from the use of the material. It is the responsibility of the holder to ensure that any systems, for whatever applications, which is based on or includes the material (whether in its entirety or in parts), meets the expected properties or functional requirements. Beijer Electronics has no obligation to supply the holder with updated versions. This Start Up document should not be considered as a complete manual. It is an aid to be able to start up a normal application quickly and easily. Use the following software and drivers in order to obtain a stable application: In this document we have used following software GX Works2 ver 1.501X FX Conigurator EN 1.40 E-Designer 7.52 ix Developer 2.10 CODESYS V3.5 SP4+ In this document we have used following hardware TOSIBOX Lock, TOSIBOX Key MELSEC FX3U: FX3U-ENET, FX3U-ENET-ADP MELSEC Q03UDE ix panel / E1000 panel 1 (33) KI_eng_ dot, Beijer Electronics Automation AB a Beijer Electronics Group company Head Office Subsidiaries Beijer Electronics Automation AB Norway, Drammen: Beijer Electronics AS, P.O. Box 426, Stora Varvsgatan 13a Finland, Vantaa: Beijer Electronics Oy, SE Malmö, SWEDEN Denmark, Roskilde: Beijer Electronics A/S, Telephone Estonia, Tallinn: Beijer Electronics Eesti Oü, Fax Latvia, Riga: Beijer Electronics SIA, Lithuania, Kaunas: Beijer Electronics UAB, Reg no VAT no SE [email protected]

2 For further information we refer to TOSIBOX user manual (tosibox homepage) Start Up document for FX3U-ENET, (KI00254) Start Up document for MELSEC QnUDE(H) with built-in ethernet port (KI00278) Start Up document how to download a project to an E1000-terminal (KI00255/KI00263) Manuals for the PLC and ix / E1000 panel can be find at This document and other Start Up documents can be obtained from our homepage. Please use the address manual@ beijer.se for feedback on our Start Up documents. 2 (33)

3 3 Table of Contents 1 Function and area of use About this Start Up document Table of Contents First step Tosibox products and accesories Connection types and Setup of Tosibox and Key Connection types Serialization of Tosibox Key and Lock Application example (Mode B) Connecting to MELSEC FX3U (FX3U-ENET-ADP) Connecting to MELSEC FX3U (FX3U-ENET) Connecting to MELSEC Q03UDE (ethernet port on cpu) Connecting to E Connecting to ix T7B SoftControl Application example (Mode A) Connecting to Mitsubishi FX3U-ENET-ADP Appendix Tosibox Lock Service port and Web interface FAQ First step For best understanding and easy working with Tosibox we recommend: - Basic knowledge of Internet connection type WAN and LAN network. - Prepare the computer with the programming tools for the PLC and HMI. - Download StartUp document for the PLC and HMI. Note! When changing parameters in Tosibox Lock, processing time can take up to 60 seconds. 5 Tosibox products and accesories Tosibox Lock Tosibox Key USB Cable Ethernet Cable AC Adapter Antennas ( 2 ) 3 (33)

4 6 Connection types and Setup of Tosibox and Key 6.1 Connection types Mode A (default setting) Lock joins an existing network as a client (one cable only). Lock will find all network devices (static and dynamic/leased IP adresses) Access can be limited with MAC/IP filtering Setup options: - DHCP Client mode (just one cable to LAN3 port) - Existing network DHCP server provides the IP address for TOSIBOX Consider the data security! - The user of the Key has access to all devices in the local network! - In case access rights need to be restricted, initiate MAC filtering (Industry-setting) or use Mode B. 4 (33)

5 Mode B (most customers use Mode B) In Mode B, the Lock creates its own protected local network for the connected devices. Only these devices, connected to the Lock directly by cable or WiFi, are accessible with the Key Lock switches automatically into Mode B when it is connected to the Internet via WAN port, 3G modem or Wifi WAN connection options: - Broadband (WAN connection) - Modem (2G, 3G or 4G) can be purchased separately from Tosibox LAN Connections options: - Device is in Client mode (TOSIBOX default setting, DHCP mode). TOSIBOX provide IP address. The device (adapter, PLC, Camera have to be in Client mode) - Fixed IP address in the device (TOSIBOX default settings, DHCP mode). Use TOSIBOX fixed IP address slot (10 IP addresses upwards, starting from TOSIBOX default IP - Fixed (already defined by customer) IP address in the device. TOSIBOX LAN IP adress will be canged to same range than fixed IP address. 5 (33)

6 6.2 Serialization of Tosibox Key and Lock Power ON to the Tosibox Lock Wait 2 minutes Wait 2 minutes for the device to power up Serialize the Tosibox Key by inserting the key in the USB port When the LED goes OFF the Key are ready to use Power ON and wait 2 minutes When blinking has stopped, Key & Lock are serialized (10 sec) Note! To handle extra Keys and Sub key, read the manual TOSIBOX Users maual 6 (33)

7 7 Application example (Mode B) 7.1 Connecting to MELSEC FX3U (FX3U-ENET-ADP) In this example we like to programming and monitor the FX3U from a PC with GX Works2. We have to setup the Tosibox in Mode B, configure the LAN-port and FX3U-ENET-ADP. PC with Tosibox Key Tosibox Lock FX3U-ENET-ADP (left side module) INTERNET WAN LAN1-3 Tosibox Key PC get the IP from LAN / DHCP WAN-port IP: from DHCP server in network LAN IP: LAN (1-3) address ranges Static: DHCP: Setup Tosibox in Mode B and connect to FX3U-ENET-ADP Use Firefox to get best layout in setup! Connect the computer to the TOSIBOX LOCK s Service Port. Type or into the web browser. The user ID is admin and the password is visible in the bottom of the TOSIBOX LOCK. Note! The internet connection in the PC should have DHCP (receives an IP address automatically). After setup 7 (33)

8 Go to Network / LAN Set the address to and the netmask to Set the LAN DHCP Server The LAN IP are set to and the setup config the first adress to and 10 address forward to There will be 10 DHCP adresses in this network: to Set the WAN to DHCP Client 8 (33)

9 Go to the Status and Network devices. Set the controlled device s (FX3U-ENET-ADP in this example) IP address to Click on New network devices and the New device popup NOTE! You can also use the Scan for LAN devices to find the devices in the same network. Click on the write sympol and edit the device 9 (33)

10 7.1.2 Connect the computer to FX3U-ENET-ADP The computer must be connected to Internet in another network than the Tosibox! Connect the Tosibox Key to USB port at the computer and the Tosibox software* will start. A dialog is shown to select to use Password. Password is recommend. * The Tosibox software will be installed the first time you connect Tosibox Key to the computer. Enter the user interface through double-clicking on the Tosibox Lock in the software window Network device show up under "Network devices". Now you should be able to connect the programming software (GX Works2) to FX3U. Note! Before connection with Tosibox you have to setup the PLC (FX3U) in direct connection (PC --- SC FX3U prog.port) (33)

11 7.1.3 Setup Ethernet modul FX3U-ENET-ADP in GX Works2 Start a new project (FX3U) and setup the ethernet port The default setting for Open Setting are 4 programming connection Setup the communication with the ethernet modul in GX Works (33)

12 7.2 Connecting to MELSEC FX3U (FX3U-ENET) In this example we like to programming and monitor the FX3U from a PC with GX Works2. We have to setup the Tosibox Lock in Mode B, configure the LAN-port and FX3U-ENET. PC with Tosibox Key Tosibox Lock FX3U-ENET-ADP (left side module) INTERNET WAN LAN Tosibox Key FX3U-ENET (right side module) Setup Tosibox in Mode B See chapter: Setup Tosibox in Mode B and connect to FX3U-ENET-ADP Below you find what s different. Go to Network / LAN Click on the write sympol and edit the device 12 (33)

13 See chapter: Connect the computer to FX3U-ENET-ADP Enter the user interface through double-clicking on the Tosibox Lock in the software window 13 (33)

14 7.2.2 Setup Ethernet modul FX3U-ENET with FX Configurator EN Start FX Configurator EN Select Module 0 (first special module on right side of the main unit) Click at Operational settings and configure the module Click Open Setting and set one MELSOFT connection (for programming) Setup the communication to the ethernet modul in GX Works (33)

15 7.3 Connecting to MELSEC Q03UDE (ethernet port on cpu) In this example we like to programming and monitor the Q03UDE from a PC with GX Works2. We have to setup the Tosibox Lock in Mode B, configure the LAN-port and Q03UDE-CPU. PC with Tosibox Key Tosibox Lock FX3U-ENET-ADP (left side module) INTERNET LAN1-3 WAN Tosibox Key FX3U-ENET (right side module) Q03UDE CPU-ethernet port Setup Tosibox in Mode B See chapter: Setup Tosibox in Mode B and connect to FX3U-ENET-ADP Below you find what s different. Go to Network / LAN 15 (33)

16 Click on the write sympol and edit the device See chapter: Connect the computer to FX3U-ENET-ADP Enter the user interface through double-clicking on the Tosibox Lock in the software 16 (33)

17 7.3.2 Setup Ethernet port in Q03UDE with GX Works2 Start a new project (Q03UDE) and setup the ethernet port The default setting for Open Setting are 16 programming connection Setup the communication to the Q03UDE (ethernet port) in GX Works (33)

18 7.4 Connecting to E1000 In this example we like to programming the E1032 from a PC with E Designer. We have to setup the Tosibox Lock in Mode B, configure the LAN-port and E1032. PC with Tosibox Key Tosibox Lock FX3U-ENET-ADP (left side module) INTERNET LAN1-3 WAN Tosibox Key E Setup Tosibox in Mode B See chapter: Setup Tosibox in Mode B and connect to FX3U-ENET-ADP Below you find what s different. Go to Network / LAN 18 (33)

19 Click on the write sympol and edit the device See chapter: Connect the computer to FX3U-ENET-ADP Enter the user interface through double-clicking on the Tosibox Lock in the software 19 (33)

20 7.4.2 Setup Ethernet port in E1032 with E-Designer Start a new project (E1032) and setup the ethernet port The IP-adress can be set in terminal with Mode-switch 1=ON at power ON. Setup the communication to E1032 in E-Designer 20 (33)

21 7.5 Connecting to ix T7B SoftControl In this example we like to transfer project to ix T7B-SC from a PC with ix Developer. We have to setup the Tosibox Lock in Mode B, configure the LAN-port and ix T7B-SC. PC with Tosibox Key Tosibox Lock FX3U-ENET-ADP (left side module) INTERNET LAN1-3 WAN Tosibox Key ix T7B SoftControl Setup Tosibox in Mode B See chapter: Setup Tosibox in Mode B and connect to FX3U-ENET-ADP Below you find what s different. Go to Network / LAN 21 (33)

22 Click on the write sympol and edit the device See chapter: Connect the computer to FX3U-ENET-ADP Enter the user interface through double-clicking on the Tosibox Lock in the software 22 (33)

23 7.5.2 Setup Ethernet port in ix T7B-SC with ix developer Make the HMI project for ix T7B-SC and download to terminal The IP-adress can be set in terminal at power ON (more info in manual) Make CODESYS project for ix T7B-SC and download to SoftControl 23 (33)

24 8 Application example (Mode A) 8.1 Connecting to Mitsubishi FX3U-ENET-ADP In this example we like to programming and monitoring the FX3U from a PC with GX Works2. We have to setup the Tosibox Lock in Mode A (default) and configure the FX3U-ENET-ADP. PC with Tosibox Key Tosibox Lock LAN3 FX3U-ENET-ADP (left side module) INTERNET Tosibox Key PC get the IP from DHCP server DHCP Server Note! - Connect the Ethernet cable to LAN3 port at Tosibox Lock. - Do not connect internet to the Tosibox Lock's WAN Port or with a 3G modem to USB Port. Doing so will automatically switch the mode of operation to Mode B! From Mode B the Tosibox Lock does not automatically return to Mode A, this needs to be done by logging in to Tosibox Lock LOCK's user interface with admin user ID. - Do not connect the controlled devices to Tosibox Lock s LAN ports. Consider the data security! - The user of the Tosibox Key has access to all devices in the local network! - In case access rights need to be restricted, initiate MAC filtering (Industry-setting) or use Mode B Setup Tosibox Lock in Mode A Default setup for Tosibox Lock are: Mode A If the Tosibox Lock are in mode B you have to login to the Lock and change the network setting. Connect the computer to the Tosibox Lock s Service Port. Type or into the web browser. The user ID is admin and the password is visible in the bottom of the Tosibox Lock. Note! The internet connection in the PC should have DHCP (Obtain an IP address automatically). Setup the network to DHCP client 24 (33)

25 8.1.2 Connect the computer to FX3U-ENET-ADP The computer must be connected to Internet in another network then the Tosibox Lock! Connect the Tosibox Key to USB port at the computer and the Tosibox software* will start. A dialog is shown to select to use Password. Password is recommend. * The Tosibox software will be installed the first time you connect Tosibox Key to the computer. Enter the user interface through double-clicking on the Tosibox Lock in the software window Network device show up under "Network devices" In this case the connection are named to FX3U-ENET_ADP_60. In other case there will be the IP-adress, ex, Now you should be able to connect the programming software (GX Works2) to FX3U. Note! Before connection with Tosibox you have to setup the PLC (FX3U) in direct connection (PC --- SC FX3U prog.port) (33)

26 8.1.3 Setup Ethernet modul FX3U-ENET-ADP in GX Works2 Start a new project (FX3U) and setup the ethernet port The default setting for Open Setting are 4 programming connection Setup the communication with the ethernet modul in GX Works (33)

27 9 Appendix 9.1 Tosibox Lock Service port and Web interface Service port Connect the computer to the Tosibox Lock s Service Port. Type or into the web browser. The user ID is admin and the password is visible in the bottom of the Tosibox Lock. Note! The internet connection in the PC should have DHCP (Obtain an IP address automatically) Web interface 27 (33)

28 28 (33)

29 29 (33)

30 30 (33)

31 31 (33)

32 32 (33)

33 9.2 FAQ How to reset Tosibox Lock to factory settings? - Can only be done by logging on to Tosibox Lock and change the settings. In the Tosibox user manual (tosibox homepage) you find: - How to erase a Tosibox Key from a Tosibox Lock? - How to handle Extra Keys and Sub Key? - How to handle a Backup Key? - How to connect a Lock with a Sub Lock? - PUK code for the Key? - Technical data for Lock? - Tosibox glossary? - Software update? - Troubleshooting? 33 (33)