NF3ADV VoIP Setup Guide (for TPG)
|
|
- Roberta French
- 5 years ago
- Views:
Transcription
1 NF3ADV VoIP Setup Guide (for TPG)
2 Configuring your NF3ADV for TPG VoIP The following steps will take you through the process of setting up your VoIP connection. This guide assumes that the NF3ADV already has an active internet connection. Step 1: Checking Computer Network Settings: You will need to connect your computer directly to your VoIP device (modem or ATA) and set the network connection on your computer to obtain an IP address automatically. Please follow the instructions appropriate for your operating system below: Below are the instructions for setting Windows XP to obtain an IP address automatically for your ethernet connection: 1. Click on the Start Menu, and go to Control Panel. 2. Click on Network Connections. (If you only see "Network and Internet Connections", open that first, and then click on "Network Connections".) 3. Right click on Local Area Connection and select Properties. 4. Double-click on Internet Protocol. 5. Select "Obtain an IP address automatically", and "Obtain DNS server address automatically". 6. Click OK, and then click OK (or Close ). Below are the instructions for setting Windows Vista to obtain an IP address automatically for your ethernet connection: 1. Click on the Start Menu, and go to Control Panel. 2. Click on Network and Sharing Centre. (If you only see "Network and Internet", open that first, and then click on "Network and Sharing Centre".) 3. Click on Manage network connections (on the left hand side of the window). 4. Right click on Local Area Connection and select Properties. 5. Double-click on Internet Protocol Version 4 (TCP/IPv4). 6. Select "Obtain an IP address automatically", and "Obtain DNS server address automatically". 7. Click OK, and then click OK again.
3 Below are the instructions for setting Windows 7 to obtain an IP address automatically for your ethernet connection: 1. Click on the Start Menu, and go to Control Panel. 2. Click on Network and Sharing Centre. (If you only see "Network and Internet", open that first, and then click on "Network and Sharing Centre".) 3. Click on Change adapter settings (on the left hand side of the window). 4. Right click on Local Area Connection and select Properties. 5. Double-click on Internet Protocol Version 4 (TCP/IPv4). 6. Select "Obtain an IP address automatically", and "Obtain DNS server address automatically". 7. Click OK, and then click OK again. Below are the instructions for setting Mac OS X to obtain an IP address automatically for your ethernet connection: 1. Click on the Apple Menu, and go to "System Preferences". 2. Click on "Network". 3. Click on Ethernet or "Built-in Ethernet". 4. Click on the "Configure" drop-down box, and select "Using DHCP" then click "Apply".
4 Step 2: Configuring your VoIP settings: 1. Navigate to in a web browser. 2. Enter admin as both the username and password and press the Login button.
5 3. Select the Switch to VoIP/NAS View option at the bottom of the screen. 4. Select the Service Domain option from the SIP Setting menu. 5. Enter the following details as provided by TPG, your VoIP Service Provider: ITEM SIP Account Phone Set WAN Interface Display Name UserName Register Name Register Password Realm Domain Proxy Server Registrar Outbound Proxy DEFINITION If you wish to use more than one VoIP account select the Multiple VoIP Accounts option or to use a single VoIP account select the 1 SIP Account option. Select the handset or DECT phone you wish to associate the selected SIP account with. Select the WAN interface to use the VoIP account with. Your VoIP Number supplied to you by TPG.** Your VoIP Number supplied to you by TPG.** Your VoIP Number supplied to you by TPG.** Your VoIP password as supplied by TPG.** aphone3.* * SIP proxy: - you can also use homephone. and tpgvoip., please confirm this with TPG before setting up the VoIP settings. ** If you have signed up for outbound calls only then you may not be provided with a VoIP phone number, if so, enter your username in the VoIP Phone number field.
6 6. Press the Save button at the bottom of the screen. Select the Switch to Advanced View button at the top of the screen. 7. Select the Reboot option from the Toolbox menu to reboot the router. 8. After logging back into the router, check that the VoIP Status is now Registered (as the example above shows). Your VoIP service is now ready for use.
NF1Adv VOIP Setup Guide (for Pennytel)
NF1Adv VOIP Setup Guide (for Pennytel) Configuring your NF1Adv for VOIP Service The following steps will take you through the process of setting up your VOIP connection. Step 1: Checking Computer Network
NF1Adv VOIP Setup Guide (for Generic VoIP Setup)
NF1Adv VOIP Setup Guide (for Generic VoIP Setup) Configuring your NF1Adv for VOIP Service The following steps will take you through the process of setting up your VOIP connection. Step 1: Checking Computer
NF5 VOIP Setup Guide (for Generic)
NF5 VOIP Setup Guide (for Generic) Configuring your NF5 for VOIP Service The following steps will take you through the process of setting up your VOIP connection. Step 1: Checking Computer Network Settings:
Step 1: Checking Computer Network Settings:
Configuring your 3G18WV for VOIP The following steps will take you through the process of setting up your VOIP connection. Step 1: Checking Computer Network Settings: You will need to connect your computer
Internet for Everyone In-Room Instructions January 2011 Version 1.3
Internet for Everyone In-Room Instructions January 2011 Version 1.3 Everywhere Internet 2006 Page 1 of 17 Connecting your computer to the Everywhere Internet network in your room 1. You need a network
STATIC IP SET UP GUIDE VERIZON 7500 WIRELESS ROUTER/MODEM
STATIC IP SET UP GUIDE VERIZON 7500 WIRELESS ROUTER/MODEM Verizon High Speed Internet for Business Verizon High Speed Internet for Business SETTING UP YOUR NEW STATIC IP CONNECTION AND IP ADDRESS(ES) This
STATIC IP SET UP GUIDE
STATIC IP SET UP GUIDE VERIZON D-LINK 2750B & ACTIONTEC GT784 WNV WIRELESS GATEWAY Verizon High Speed Internet for Business Verizon High Speed Internet for Business YOUR NEW STATIC IP CONNECTION AND SET
Actiontec GT784WN Router
Table of Contents General Information...1 Verify Computer Settings...1 Router Installation...3 Configuring Your Router...3 Configuring Your Computer...7 Configuring Your Email...9 General Information Router
RingCentral Office. Configure Aastra phones with RingCentral
TM RingCentral Office Configure Aastra phones with RingCentral Configuring Aastra phones Overview... 2 Getting ready to setup your Aastra phones... 2 Configuring the Aastra Phone... 4 Overview Aastra s
P-3202H-Bb. G-PON VoIP IAD DEFAULT LOGIN DETAILS. Firmware v1.0 Edition 1, 09/2009. IP Address: http://192.168.1.1. Password: 1234
P-3202H-Bb G-PON VoIP IAD Firmware v1.0 Edition 1, 09/2009 DEFAULT LOGIN DETAILS IP Address: http://192.168.1.1 User Name admin Password: 1234 Copyright 2009 Device Panels POWER PON ETHERNET 1~4 PHONE
ACT High Speed WiMAX Internet
ACT High Speed WiMAX Internet Internet Configuration Manual This manual walks you through the steps of configuring your computer for High Speed WiMAX Internet service with Windows 7, Vista, XP, 2000, And
RingCentral Office. Configure Grandstream phones with RingCentral. To contact RingCentral, please visit www.ringcentral.com or call 1-800-574-5290.
TM RingCentral Office Configure Grandstream phones with RingCentral Configuring Grandstream phones Overview... 2 Getting ready to setup your Grandstream phones... 2 Configuring the Grandstream Phone...
Wireless G Broadband quick install
Wireless G Broadband Router quick install guide Model 503693 INT-503693-QIG-0608-02 Thank you for purchasing the INTELLINET NETWORK SOLUTIONS Wireless G Broadband Router, Model 503693. This quick install
Internet Guide. Prepared for 55 John Street
Internet Guide Prepared for 55 John Street I. Internet Service How do I connect to the Internet? WiFi (Wireless Connectivity) is available throughout the building. In order to connect, you will need a
Dial Up Config & Connecting Instructions with Graphics
Dial Up Config & Connecting Instructions with Graphics Dial Up Config & Connecting Below are the Basic Manual Configurations Connecting to the Internet for the following operating systems: Windows 2000
HYPERLINK Internet PC setup guide. HYPERLINK Internet support helpdesk at 1-866-302-5525.
HYPERLINK Internet support helpdesk at 1-866-302-5525. Congratulations on your new residence and welcome to HYPERLINK Internet service. In a few short moments you will be connected to one of the fastest
Sentral servers provide a wide range of services to school networks.
Wazza s QuickStart Publishing iweb Sites to a Sentral Server Background Mac OS X, Sentral, iweb 09 Sentral servers provide a wide range of services to school networks. A Sentral server provides a publishing
FLX VoIP Registering with Avaya IP Office 500
FLX VoIP Registering with Avaya IP Office 500 Date: April 5 th, 2012 This technical note gives a detailed description on how to register a Revolabs FLX conference phone with Avaya IP Office 500 PBX. On
Manual Wireless Extender Setup Instructions. Before you start, there are two things you will need. 1. Laptop computer 2. Router s security key
1 Manual Wireless Extender Setup Instructions Before you start, there are two things you will need. 1. Laptop computer 2. Router s security key Setting up LAN Static IP on PC We need to set up a Static
Integrating a Hitachi IP5000 Wireless IP Phone
November, 2007 Avaya Quick Edition Integrating a Hitachi IP5000 Wireless IP Phone This application note explains how to configure the Hitachi IP5000 wireless IP telephone to connect with Avaya Quick Edition
Prestige 2302R Series
VoIP Station Gateway Quick Start Guide Version 3.60 6/2005 Overview This Quick Start Guide covers the Prestige (P2302R) and (P2302RL) models. It explains how to use your Prestige to make phone calls through
Setting up Sharp MX-Color Imagers for Inbound Fax Routing to Email or Network Folder
Setting up Sharp MX-Color Imagers for Inbound Fax Routing to Email or Network Folder MX-2300, MX-2600, MX-2700, MX-3100, MX-3501, MX-4501, MX-5500, MX-6200, MX-6201, MX-7000, MX-7001, *MX-M850, *MX-M950,
You may refer the Quick Installation Guide in the package box for more information.
Hardware Installation: 1. Turn off your modem. 2. Use one Ethernet cable to connect your modem to WAN port (Blue) port of BR-6228nC. 3. Use another Ethernet cable to connect your PC to one LAN Port (Yellow)
Model:BL-WDR3750 750Mbps Wireless Dual Band 11AC Router
Quick Installation Guide Model:BL-WDR3750 750Mbps Wireless Dual Band 11AC Router 1.Connecting the device Note: Please use wired network connections only to configure the Router. 1 Connect the WAN port
1. Hardware Installation
4 Port 10/100M Internet Broadband Router with USB Printer server Quick Installation Guide #4824904AXZZ0 1. Hardware Installation A. System Requirement Before you getting started, make sure that you meet
3rd Party VoIP Phone Setup Guide (Panasonic 500-550b)
3rd Party VoIP Phone Setup Guide (Panasonic 500-550b) We are changing how we add 3rd party VoIP phones to accounts. Going forward, you can simply add a 3rd Party Softphone and use those credentials to
3rd Party VoIP Phone Setup Guide (Panasonic UT113-123)
3rd Party VoIP Phone Setup Guide (Panasonic UT113-123) We are changing how we add 3rd party VoIP phones to accounts. Going forward, you can simply add a 3rd Party Softphone and use those credentials to
Quick Installation Guide DAP-1360. Wireless N 300 Access Point & Router
DAP-1360 Wireless N 300 Access Point & Router BEFORE YOU BEGIN Delivery Package Access point DAP-1360 Power adapter DC 12V Ethernet cable (CAT 5E) (brochure). If any of the items are missing, please contact
Network Setup Guide. 1 Glossary. 2 Operation. 1.1 Static IP. 1.2 Point-to-Point Protocol over Ethernet (PPPoE)
Network Setup Guide 1 Glossary 1.1 Static IP Computers are communicated and recognized by their own unique IP addresses over the Internet. Static IP provided by your ISP (Internet Service Provider) means
DIR-100. Before You Begin. Check Your Package Contents. Triple Play Router
This product can be set up using a current web browser. DIR-100 Triple Play Router Before You Begin Make sure you have all the necessary information and equipment on hand before beginning the installation.
BiPAC 7404V series. VoIP/(802.11g) ADSL2+ (VPN) Firewall Router. Quick Start Guide
BiPAC 7404V series VoIP/(802.11g) ADSL2+ (VPN) Firewall Router Quick Start Guide VoIP/(802.11g) ADSL2+ (VPN) Firewall Router For more detailed instructions on configuring and using the Billion VoIP/(802.11g)
Configuring PPP And SIP
Copyright Copyright 2005. All rights reserved. The content of this manual is subject to change without notice. The information and messages contained herein are proprietary to. No part of this manual may
P-2302HWUDL-P1. Quick Start Guide. 802.11g Wireless VoIP Station Gateway. with Built-in DECT Base Station
P-2302HWUDL-P1 802.11g Wireless VoIP Station Gateway with Built-in DECT Base Station Quick Start Guide Version 3.60 Edition 1 3/2007 Overview The P-2302HWUDL-P1 model is a router with IEEE 802.11g wireless
Turn off all of your network devices, including your computer, Modem and the Router.
Note The product model shown in this part is TL-R460, as an example. Turn off all of your network devices, including your computer, Modem and the Router. Connect the WAN port on your Router to the Modem
How to configure Linksys SPA 941 942 for VOIP Connections
How to configure Linksys SPA 941 942 for VOIP Connections Congratulations. Welcome to VOIP Connections family. 1.) Connect the phone properly. Make sure the phone is connected securely to your router or
Chapter 2 Preparing Your Network
Chapter 2 Preparing Your Network This document describes how to prepare your network to connect to the Internet through a router and how to verify the readiness of your broadband Internet service from
BiPAC 74xx series. VoIP Quick Install Guide
BiPAC 74xx series VoIP ADSL2/2+ Modem/Routers VoIP Quick Install Guide This guide covers the initial VoIP set-up only. Please contact your VoIP service provider for their full VoIP setting. This guide
SIP Trunking using Optimum Business SIP Trunk Adaptor and the Allworx 6x IP PBX 7.1.6.1
ALLWORX SIP Trunking using Optimum Business SIP Trunk Adaptor and the Allworx 6x IP PBX 7.1.6.1 Goal The purpose of this configuration guide is to describe the steps needed to configure the Allworx 6x
Please use only wired network connections to configure the router.
Note Please use only wired network connections to configure the router. Connect the WAN port on your Router to the Modem s LAN port with an Ethernet cable. Note If connecting the TL-WR543G to the WISP
Configure cordless IP phones with RingCentral. RingCentral Office
RingCentral Office Configure cordless IP phones with RingCentral 2011 To contact RingCentral, RingCentral, Inc. All Rights please Reserved. visit RingCentral www.ringcentral.com and the or call 1-800-574-5290.
Apple Mac. AT&T DSL Internet Service Implementation Planner Apple Mac PC Configuration Guide Version 1.2 Page 1
Apple Mac Page 1 Apple Mac Setup Welcome to AT&T DSL Internet Service! This guide is designed to help you configure your Mac to access the Internet quickly and easily using AT&T DSL. Before You Begin First,
Turn off all of your network devices, including your computer, Modem and the Router.
Note Please use only wired network connections to configure the Router. Turn off all of your network devices, including your computer, Modem and the Router. Connect the WAN port on your Router to the Modem
Troubleshooting Guide
Troubleshooting Guide Before you start troubleshooting: Power down the Tooway modem for 60 seconds. Connect a computer directly (via Ethernet cable) to the Tooway modem Power the Tooway modem and wait
Dramatically simplifying voice and data networking HOW-TO GUIDE. Bundle Quick Start Guide
Dramatically simplifying voice and data networking HOW-TO GUIDE Bundle Quick Start Guide 2 edgebox How-To Guide - Table of Contents Scope of the Quick-Start Guide...3 edgebox bundles...3
Snom 720 and Elastix Server
Snom 720 and Elastix Server Setup Guide http://www.elastix.org 1.0 Setup Diagram Figure 1-1 is a setup diagram for a single IP Phone Snom 720 configuration. The phone is setup as a SIP telephony device.
Setting Up Sharp MX-Color Imagers To Scan To Email
Setting Up Sharp MX-Color Imagers To Scan To Email MX-2300, MX-2600, MX-2700, MX-3100, MX-3501, MX-4501, MX-5500, MX-6200, MX-6201, MX-7000, MX-7001, MX-M850, MX-M950, MX-M1100 Step 1. Click Start > Run
NETVIGATOR Wireless Modem Setup Guide. (TG789Pvn)
NETVIGATOR Wireless Modem Setup Guide (TG789Pvn) Configure the NETVIGATOR Wireless Modem Make sure that system meets the following requirement prior to NETVIGATOR Wireless Modem usage: - Subscribers who
Check Your Package Contents. CD-ROM containing Manual and Warranty
This product can be set up using any current web browser, i.e., Internet Explorer 6 or Netscape Navigator 6.2.3. DVA-G3340S Wireless VoIP Router Before You Begin If you purchased this Router to share your
DVG-2101SP VoIP Telephone Adapter
This product can be set up using any current web browser, i.e., Internet Explorer 6 or Netscape Navigator 6.2.3. DVG-2101SP VoIP Telephone Adapter Before You Begin 1. If you purchased this VoIP Telephone
Application Note Configuring the UGate 3000 for use with ClipMail Pro and ClipExpress
Application Note Configuring the UGate 3000 for use with Introduction This Application Note guides the ClipMail user through the UGate gateway configuration process by using a simple dial up connection
Configuring an IP (SIP) Polycom Soundstation on the Avaya IP Office
Hardware used for this documentation Polycom Soundstation IP 6000 Avaya IP500V2 firmware 7.0.23 Set the Polycom with an IP Address Step 1: Initial setup If your Soundstation does not automatically register
Multi-Homing Dual WAN Firewall Router
Multi-Homing Dual WAN Firewall Router Quick Installation Guide M73-APO09-400 Multi-Homing Dual WAN Firewall Router Overview The Multi-Homing Dual WAN Firewall Router provides three 10/100Mbit Ethernet
From a Finder window choose Applications (shown circled in red) and then double click the Tether icon (shown circled in green).
From a Finder window choose Applications (shown circled in red) and then double click the Tether icon (shown circled in green). You will be presented with a dialog box asking for you to enter an ad-hoc
How to add a SIP server How to register a handset
How to add a SIP server How to register a handset Contents Contents... 1 Hardware required equipment... 2 Software required equipment... 3 Add server... 3 Register handset to base... 7 1 of 12 Hardware
ZyXEL VoIP 2602HWL - Setup guide
POWER A/C Adapter 4 3 2 1 PHONE 2 PHONE 1 LINE 2.0 Setup Network 2.1 Click on the Start button on the bottom left hand corner, and then choose Control Panel. ZyXEL VoIP 2602HWL - Setup guide Contents 1.
Version 0.1 June 2010. Xerox WorkCentre 7120 Fax over Internet Protocol (FoIP)
Version 0.1 June 2010 Xerox WorkCentre 7120 Fax over Internet Protocol (FoIP) Thank you for choosing the Xerox WorkCentre 7120. Table of Contents Introduction.........................................
Firewall VPN Router. Quick Installation Guide M73-APO09-380
Firewall VPN Router Quick Installation Guide M73-APO09-380 Firewall VPN Router Overview The Firewall VPN Router provides three 10/100Mbit Ethernet network interface ports which are the Internal/LAN, External/WAN,
If no telephone is needed, please connect the LINE port of the Modem Router to the wall jack using the telephone line directly.
Note Please use only wired network connections to configure the Router. Power down all of your network devices, including your computer(s) and the Modem Router. If you currently use a modem, disconnect
Opera 240 System DECT Integration. with Gigaset N720 IP PRO Base Station. and Gigaset N720 DM PRO Manager. Installation and User Guide
Opera 240 System DECT Integration with Gigaset N720 IP PRO Base Station and Gigaset N720 DM PRO Manager Installation and User Guide Contents 1 Introduction... 3 2 To set up the Opera 240 System and the
NETWORK SETUP INSTRUCTIONS
NETWORK SETUP INSTRUCTIONS How to Connect AVTECH Product to Internet To connect AVTECH DVR or network camera to Internet, you need to: 1). Figure out your network environment, and have related IP information
Netcomm NB604N. Modem Configuration Guide. Netcomm NB604N. Configuring in Layer2 PPPoE for Windows XP and 2000 IMPORTANT MESSAGE
Configuring in Layer2 PPPoE for Windows XP and 2000 IMPORTANT MESSAGE Your modem has been pre-configured, you do not need to follow each step of the set-up guide but should retain this document in case
Optimum Business SIP Trunk Set-up Guide
Optimum Business SIP Trunk Set-up Guide For use with IP PBX only. SIPSetup 07.13 FOR USE WITH IP PBX ONLY Important: If your PBX is configured to use a PRI connection, do not use this guide. If you need
If you need additional assistance please contact our Technical Support Center at 24 hours a day, 7 days a week.
Cisco SPA 2100 Phone Adapter Installation Manual Index Installation of the Cisco SPA 2100 Phone Adapter to NationPhone P. 1 Index, before you begin, and what is included P.2 Installing the NationPhone
The ECU Wireless system uses a captive portal authentication system. There are three steps to configure your computer for wireless access:
ECU WIRELESS SETUP The ECU Wireless system uses a captive portal authentication system. There are three steps to configure your computer for wireless access: 1. Install a wireless network card into your
D-LINK DPH-140S SIP PHONE INSTALLATION GUIDE
pag.1 D-LINK DPH-140S SIP PHONE INSTALLATION GUIDE pag.2 SUMMARY SKYPHO VOIP SERVICE...3 DPH-140S PACKAGE CONTENT...3 DEVICE PHYSICAL CONNECTION...4 ACCESS TO THE DEVICE...6 Accesso to the IP Phone when
19 LCD / 8 CHANNEL DVR COMBO WITH 160GB HDD & 4 CAMERAS
19 LCD / 8 CHANNEL DVR COMBO WITH 160GB HDD & 4 CAMERAS Overview - Remote Viewing MODEL: SG19LD804-161 www.lorexcctv.com Copyright 2007 LOREX Technology Inc. Remote Viewing Overview Remote Viewing Overview
Step-by-Step Setup Guide Wireless File Transmitter FTP Mode
EOS Step-by-Step Setup Guide Wireless File Transmitter FTP Mode Infrastructure & Ad Hoc Networks Mac OS X 10.5-10.6 2012 Canon U.S.A., Inc. All Rights Reserved. Reproduction in whole or in part without
SIP Trunking using Optimum Business SIP Trunk Adaptor and the Cisco Call Manager Express Version 8.5
CISCO SIP Trunking using Optimum Business SIP Trunk Adaptor and the Cisco Call Manager Express Version 8.5 Goal The purpose of this configuration guide is to describe the steps needed to configure the
VoIPon www.voipon.co.uk sales@voipon.co.uk Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
VoiceGear/3CX Integration Guide Ver.0.1 Page 2 1. OVERVIEW... 3 1.1 SETTING UP 3CX PBX...4 1.2 SETTING UP VOICEGEAR GATEWAY...5 2. VOICEGEAR-3CX SIP INTEGRATION... 6 2.1 3CX CONFIGURATION...7 2.2 VOICEGEAR
1. Panel Descriptions... 1. 2. Connecting the 4 Ports VoIP ADSL Router... 3. 3. Setting up the TCP/IP in Windows... 5
Contents 1. Panel Descriptions... 1 2. Connecting the 4 Ports VoIP ADSL Router... 3 3. Setting up the TCP/IP in Windows... 5 Windows ME/98... 5 Windows 2000... 6 Windows XP... 7 4. Setting up the 4 Ports
Wazza s QuickStart 17. Leopard Server - Blogs & Wikis
Wazza s QuickStart 17. Leopard Server - Blogs & Wikis About this Document This document is the 17th in a series of documents describing the process of installing and configuring a Mac OS X 10.5 Server
Scan to E-mail Quick Setup Guide
Xerox WorkCentre M118i Scan to E-mail Quick Setup Guide 701P42574 This guide provides a quick reference for setting up the Scan to E-mail feature on the Xerox WorkCentre M118i. It includes procedures for:
Firmware Release Notes
NF4V VDSL/ADSL WiFi Gigabit Modem Router Firmware Release Notes Copyright Copyright 2015 NetComm Wireless Limited. All rights reserved. The information contained herein is proprietary to NetComm Wireless.
Using a simple crossover RJ45 cable, you can directly connect your Dexter to any computer.
Dexter is a network device using the Ethernet protocol to connect and communicate with other devices on the network: Computers, routers, DHCP servers. Thus you have to setup your Dexter and your network
Please use only wired network connections to configure the Router.
Note Please use only wired network connections to configure the Router. Power down all of your network devices, including your computer(s) and the Modem Router. If you currently use a modem, disconnect
Creating Custom Nameservers Contents
Creating Custom Nameservers Contents Goals... 2 Register Name Servers... 2 Setup Private NameServers in WHM... 4 Adding IP addresses for your name server... 5 Conclusion... 5 Goals This guide will help
VOIP-500 Series Phone CUCM 8.0.3a Integration Guide
I. Introduction This provides general instructions for integration of the VOIP-500 Series Phone with a Cisco Call Manager installation. It is recommended to read this instruction set completely before
Shield Pro. Quick Start Guide
Shield Pro In the box: Power Adapter Shield Network Cables Let s get started! Before installing Shield you will first need to determine which operating mode best fits your needs. To help with this process,
Front LEDs... 2 Rear Ports... 3 BASIC INSTALLATION... 4 Connecting Your Router... 5 Network Configuration... 6
0 P a g e Table of contents Front LEDs... 2 Rear Ports... 3 BASIC INSTALLATION... 4 Connecting Your Router... 5 Network Configuration... 6 Gateway Configuration... 11 Accessing your gateway... 11 Displaying
NB6 Series Quality of Service (QoS) Setup (NB6Plus4, NB6Plus4W Rev1)
NB6 Series Quality of Service (QoS) Setup (NB6Plus4, NB6Plus4W Rev1) NB6 Series and Quality of Service (QoS) The following Quality of Service (QoS) settings offer a basic setup example, setting up 3 devices
Registering with Cisco UCM
FLX VoIP Registering with Cisco UCM Date: May 15 th, 2012 This technical note gives a detailed description on how to register a Revolabs FLX conference phone with a Cisco Unified Communications Manager
Installation. Note Please use only wired network connections to configure the router.
Installation Note Please use only wired network connections to configure the router. Power down all your network devices, including your computer(s) and the Modem Router. If you currently use a modem,
HRG Performance Series DVR DDNS Support Application Note (hrgddns)
HRG Performance Series DVR DDNS Support Application Note (hrgddns) This document describes how to enable and configure Dynamic DNS (DDNS) functionality on the HRG Performance Series digital video recorder
Note The product model shown in this QIG is TD-8817, as an example.
Note The product model shown in this QIG is TD-8817, as an example. Turn off all of your network devices, including your computer and the Modem Router. If you currently use a modem, disconnect it now -
DI-634M. Check Your Package Contents. This product can be set up using any current web browser, i.e., Internet Explorer 6 or Netscape Navigator 7.
This product can be set up using any current web browser, i.e., Internet Explorer 6 or Netscape Navigator 7. DI-634M 108G MIMO Wireless Router Before You Begin 1. If you purchased this router to share
Quick Installation Guide DIR-620. Multifunction Wireless Router Supporting GSM, CDMA, WiMAX with Built-in 4-port Switch
DIR-620 Multifunction Wireless Router Supporting GSM, CDMA, WiMAX with Built-in 4-port Switch BEFORE YOU BEGIN Delivery Package Multifunction wireless router DIR-620 Power adapter DC 5V/2.5A Ethernet cable
Smart Telephone System
IG7600 Smart Telephone System Quick Installation Guide Copyright 2013, All Rights Reserved. Ver11140311 IG7600 Smart Telephone System Quick Installation Guide Powering up 1. Plug the IG7600 in and allow
Broadband DSL Quick Start Set Up Guide
Broadband DSL Quick Start Set Up Guide Index What s in the box?... 1 Applying the DSL filters... 2 What devices must be filtered... 3 Connecting the DSL modem... 3-5 Connecting a computer... 5 Setting
Dynamic DNS How-To Guide
Configuration Guide Dynamic DNS How-To Guide Overview This guide will show you how to set up a Dynamic DNS host name under the D-Link DDNS service with your D-Link ShareCenter TM. Dynamic DNS is a protocol
Yealink Phones User Guide. 2003-2012 Bicom Systems
I Table of Contents Part I Introduction 1 Part II Requirements 1 Part III Installation 2 1 Power... Adapter 3 2 Power... over Ethernet (PoE) 3 3 IP Address... 3 4 Factory... Settings 3 4 Part IV Registering
Installation. If you currently use a modem, disconnect it now - the Modem Router will replace your current modem.
Installation Note Please use only wired network connections to configure the Modem Router. If you currently use a modem, disconnect it now - the Modem Router will replace your current modem. Connect your
Quick Start Guide. Cisco SPA232D Mobility Enhanced ATA
Quick Start Guide Cisco SPA232D Mobility Enhanced ATA Package Contents Analog Telephone Adapter Ethernet Cable Phone Cable Power Adapter Quick Start Guide Product CD-ROM Welcome Thank you for choosing
Citrix Client Install Instructions
Citrix Client Install Instructions If you are using Citrix remotely, Information Technology Services recommends updating Citrix client to the newest version available online. You must be an administrator
Step by step guide for connecting PC to wired LAN at dormitories of University of Pardubice
Step by step guide for connecting PC to wired LAN at dormitories of University of Pardubice English version Version 1.1 July 2008 Information Cente University of Pardubice Content A. Windows XP... 2 B.
How to connect to NAU s WPA2 Enterprise implementation in a Residence Hall:
How to connect to NAU s WPA2 Enterprise implementation in a Residence Hall: General Settings To connect to the ResNet-Secure SSID, a device is needed that supports 802.1X authentication and WPA2 Enterprise.
HRG Performance Series DVR DDNS Support Application Note (DynDNS)
HRG Performance Series DVR DDNS Support Application Note (DynDNS) This document describes how to enable and configure Dynamic DNS (DDNS) functionality on the HRG Performance Series digital video recorder
Prestige 314 Read Me First
Prestige 314 Read Me First Console WAN 10M PORT Prestige Rear Panel Connections CONNECTION Use an RS-232 console cable. Use the cable that came with your broadband modem. LAN 10/100M Port Number COMPUTER
Connecting a Personal Computer or Laptop to RezNet
Connecting a Personal Computer or Laptop to RezNet Preamble: Humber has outfitted each suite in Residence with an Ethernet connection. Should you wish to access Internet resources, you may do so by following
Configuring the Active Directory Plug-in
Wazza s QuickStart Configuring the Active Directory Plug-in Mac OS X 10.3.4 Background Using the Mac OS X 10.3.x built-in Active Directory (AD) plug-in, Mac users can authenticate with a Windows Active
NETWORK SETUP GLOSSARY
GLOSSARY NETWORK SETUP Static IP PPPoE DHCP DDNS Static IP Computers are communicated and recognized by their own unique IP addresses over the Internet. Static IP provided by your ISP (Internet Service