Premium Double Hung Windows
|
|
|
- Piers Marsh
- 9 years ago
- Views:
Transcription
1 gress Data The following opening specifications have been provided to assist you in determining compliance to gress codes based on BOCA and UBC code requirements as follows. ach criteria below must be met to be considered an egress window unit.. The units must be operable from the inside without the use of separate tools. 2. All egress from sleeping rooms must have a minimum net clear opening of 5.7 square feet. 3. The minimum net clear opening height dimension shall be. The minimum net clear opening width dimension shall be 20". Calculations based on 82 /2" header height. Calculations based on 50/50 Sash Split. meets gress 4. The Floor To Sill Height Column is calculated by measuring from the clear opening sill (when unit is open) to the floor. This height cannot be more than 44" above the floor. Charts can be used are for all glass types available. GSS DATA Light, Vent & gress Data 24 Callout width LIGHT Page of 5 VNT &.O. SIZ ( & HIGHT) SASH SIZ ( & HIGHT) GLASS SIZ ( & HIGHT) TOTAL CLA OPNING (Minimum 5.7 sq ft) CLA OPNING (Minimum 20") CLA OPNING HIGHT (Minimum ) FLOO TO SILL HIGHT (Can not exceed 44") DAYLIGHT OPNING Per Sash VNTILATION 24 x " x 29.50" Width " Width " Height 4.75" Height 3.75" Width " Width " Height " Height.5625" " 9.332" Bottom Sash.326 Top Sash x " x 35.50" Width " Width " Height 7.75" Height 6.75" Width " Width " Height " Height " " " Bottom Sash.68 Top Sash x " x 4.50" Width " Width " Height 20.75" Height 9.75" Width " Width " Height " Height " " " Bottom Sash Top Sash x " x 47.50" Width " Width " Height 23.75" Height 22.75" Width " Width " Height " Height " " " Bottom Sash Top Sash x " x 53.50" Width " Width " Height 26.75" Height 25.75" Width " Width " Height " Height " " 3.075" Bottom Sash Top Sash x " x 59.50" Width " Width " Height 29.75" Height 28.75" Width " Width " Height " Height " " " Bottom Sash 3.03 Top Sash x " x 65.50" Width " Width " Height 32.75" Height 3.75" Width " Width " Height " Height " " 9.075" Bottom Sash Top Sash x " x 7.50" Width " Width " Height 35.75" Height 34.75" Width " Width " Height " Height " " 3.075" Bottom Sash 3.84 Top Sash x " x 77.50" Width " Width " Height 38.75" Height 37.75" Width " Width " Height " Height " " 7.075" Bottom Sash 4.69 Top Sash Maximum travel is 3.457".
2 gress Data The following opening specifications have been provided to assist you in determining compliance to gress codes based on BOCA and UBC code requirements as follows. ach criteria below must be met to be considered an egress window unit.. The units must be operable from the inside without the use of separate tools. 2. All egress from sleeping rooms must have a minimum net clear opening of 5.7 square feet. 3. The minimum net clear opening height dimension shall be. The minimum net clear opening width dimension shall be 20". 4. The Floor To Sill Height Column is calculated by measuring from the clear opening sill (when unit is open) to the floor. This height cannot be more than 44" above the floor. Calculations based on 82 /2" header height. Calculations based on 50/50 Sash Split. meets gress Charts can be used are for all glass types available. GSS DATA Light, Vent & gress Data 30 Callout width LIGHT Page 2 of 5 VNT & OUGH OPNING SIZ ( & HIGHT) SASH SIZ ( & HIGHT) GLASS SIZ ( & HIGHT) TOTAL CLA OPNING (Minimum 5.7 sq ft) CLA OPNING (Minimum 20") CLA OPNING HIGHT (Minimum ) FLOO TO SILL HIGHT (Can not exceed 44") DAYLIGHT OPNING Per Sash VNTILATION 30 x " x 29.50" Height 4.75" Height 3.75" Height " Height.5625" " " Bottom Sash.792 Top Sash x " x 35.50" Height 7.75" Height 6.75" Height " Height " " " Bottom Sash Top Sash x " x 4.50" Height 20.75" Height 9.75" Height " Height " " " Bottom Sash Top Sash x " x 47.50" Height 23.75" Height 22.75" Height " Height " " " Bottom Sash Top Sash x " x 53.50" Height 26.75" Height 25.75" Height " Height " " 3.075" Bottom Sash 3.74 Top Sash x " x 59.50" Height 29.75" Height 28.75" Height " Height " " " Bottom Sash 4.94 Top Sash x " x 65.50" Height 32.75" Height 3.75" Height " Height " " 9.075" Bottom Sash Top Sash x " x 7.50" Height 35.75" Height 34.75" Height " Height " " 3.075" Bottom Sash 5.55 Top Sash x " x 77.50" Height 38.75" Height 37.75" Height " Height " " 7.075" Bottom Sash Top Sash Maximum travel is 3.457".
3 gress Data The following opening specifications have been provided to assist you in determining compliance to gress codes based on BOCA and UBC code requirements as follows. ach criteria below must be met to be considered an egress window unit.. The units must be operable from the inside without the use of separate tools. 2. All egress from sleeping rooms must have a minimum net clear opening of 5.7 square feet. 3. The minimum net clear opening height dimension shall be. The minimum net clear opening width dimension shall be 20". 4. The Floor To Sill Height Column is calculated by measuring from the clear opening sill (when unit is open) to the floor. This height cannot be more than 44" above the floor. Calculations based on 82 /2" header height. Calculations based on 50/50 Sash Split. meets gress Charts can be used are for all glass types available. GSS DATA Light, Vent & gress Data 36 Callout width LIGHT Page 3 of 5 VNT &.O. SIZ ( & HIGHT) SASH SIZ ( & HIGHT) GLASS SIZ ( & HIGHT) TOTAL CLA OPNING (Minimum 5.7 sq ft) CLA OPNING (Minimum 20") CLA OPNING HIGHT (Minimum ) FLOO TO SILL HIGHT (Can not exceed 44") DAYLIGHT OPNING Per Sash VNTILATION 36 x " x 29.50" Bottom Sash: Width " Height 4.75" Top Sash: Width " Height 3.75" Height " Height.5625" " " Bottom Sash Top Sash x " x 35.50" Width " Width " Height 7.75" Height 6.75" Height " Height " " " Bottom Sash Top Sash x " x 4.50" Width " Width " Height 20.75" Height 9.75" Height " Height " " " Bottom Sash Top Sash x " x 47.50" Width " Width " Height 23.75" Height 22.75" Height " Height " " " Bottom Sash Top Sash x " x 53.50" Width " Width " Height 26.75" Height 25.75" Height " Height " " 3.075" Bottom Sash Top Sash x " x 59.50" Width " Width " Height 29.75" Height 28.75" Height " Height " " " Bottom Sash Top Sash x " x 65.50" Width " Width " Height 32.75" Height 3.75" Height " Height " " 9.075" Bottom Sash 5.89 Top Sash x " x 7.50" Width " Width " Height 35.75" Height 34.75" Height " Height " " 3.075" Bottom Sash Top Sash x " x 77.50" Width " Width " Height 38.75" Height 37.75" Height " Height " " 7.075" Bottom Sash 7.02 Top Sash Maximum travel is 3.457".
4 gress Data The following opening specifications have been provided to assist you in determining compliance to gress codes based on BOCA and UBC code requirements as follows. ach criteria below must be met to be considered an egress window unit.. The units must be operable from the inside without the use of separate tools. 2. All egress from sleeping rooms must have a minimum net clear opening of 5.7 square feet. 3. The minimum net clear opening height dimension shall be. The minimum net clear opening width dimension shall be 20". 4. The Floor To Sill Height Column is calculated by measuring from the clear opening sill (when unit is open) to the floor. This height cannot be more than 44" above the floor. Calculations based on 82 /2" header height. Calculations based on 50/50 Sash Split. meets gress Charts can be used are for all glass types available. GSS DATA Light, Vent & gress Data 42 Callout width LIGHT Page 4 of 5 VNT &.O. SIZ ( & HIGHT) SASH SIZ ( & HIGHT) GLASS SIZ ( & HIGHT) TOTAL CLA OPNING (Minimum 5.7 sq ft) CLA OPNING (Minimum 20") CLA OPNING HIGHT (Minimum ) FLOO TO SILL HIGHT (Can not exceed 44") DAYLIGHT OPNING Per Sash VNTILATION 42 x " x 29.50" Height 4.75" Height 3.75" Height " Height.5625" " " Bottom Sash Top Sash x " x 35.50" Height 7.75" Height 6.75" Height " Height " " " Bottom Sash Top Sash x " x 4.50" Height 20.75" Height 9.75" Height " Height " " " Bottom Sash 4.85 Top Sash x " x 47.50" Height 23.75" Height 22.75" Height " Height " " " Bottom Sash 4.95 Top Sash x " x 53.50" Height 26.75" Height 25.75" Height " Height " " 3.075" Bottom Sash Top Sash x " x 59.50" Height 29.75" Height 28.75" Height " Height " " " Bottom Sash Top Sash x " x 65.50" Height 32.75" Height 3.75" Height " Height " " 9.075" Bottom Sash 7.07 Top Sash x " x 7.50" Height 35.75" Height 34.75" Height " Height " " 3.075" Bottom Sash Top Sash x " x 77.50" Height 38.75" Height 37.75" Height " Height " " 7.075" Bottom Sash Top Sash Maximum travel is 3.457".
5 gress Data The following opening specifications have been provided to assist you in determining compliance to gress codes based on BOCA and UBC code requirements as follows. ach criteria below must be met to be considered an egress window unit.. The units must be operable from the inside without the use of separate tools. 2. All egress from sleeping rooms must have a minimum net clear opening of 5.7 square feet. 3. The minimum net clear opening height dimension shall be. The minimum net clear opening width dimension shall be 20". 4. The Floor To Sill Height Column is calculated by measuring from the clear opening sill (when unit is open) to the floor. This height cannot be more than 44" above the floor. Calculations based on 82 /2" header height. Calculations based on 50/50 Sash Split. meets gress Charts can be used are for all glass types available. GSS DATA Light, Vent & gress Data 48 Callout width LIGHT Page 5 of 5 VNT &.O. SIZ ( & HIGHT) SASH SIZ ( & HIGHT) GLASS SIZ ( & HIGHT) TOTAL CLA OPNING (Minimum 5.7 sq ft) CLA OPNING (Minimum 20") CLA OPNING HIGHT (Minimum ) FLOO TO SILL HIGHT (Can not exceed 44") DAYLIGHT OPNING Per Sash VNTILATION 48 x " x 29.50" Height 4.75" Height 3.75" Width " Width " Height " Height.5625" " " Bottom Sash 3.90 Top Sash x " x 35.50" Height 7.75" Height 6.75" Width " Width " Height " Height " " " Bottom Sash Top Sash x " x 4.50" Height 20.75" Height 9.75" Width " Width " Height " Height " " " Bottom Sash 4.90 Top Sash x " x 47.50" Height 23.75" Height 22.75" Width " Width " Height " Height " " " Bottom Sash Top Sash Width " Width " 6.255** 2 48 x " x 53.50" Height 26.75" Height 25.75" Height " Height " " 3.075" Bottom Sash 6.62 Top Sash x " x 59.50" Height 29.75" Height 28.75" Width " Width " Height " Height " " " Bottom Sash Top Sash x " x 65.50" Height 32.75" Height 3.75" Width " Width " Height " Height " " 9.075" Bottom Sash Top Sash x " x 7.50" Height 35.75" Height 34.75" Width " Width " Height " Height " " 3.075" Bottom Sash 9.78 Top Sash x " x 77.50" Height 38.75" Height 37.75" Width " Width " Height " Height " " 7.075" Bottom Sash Top Sash Maximum travel is 3.457". 2 Please note 48 x 54 size does not meet egress due to the Clear Opening Height Minimum rule is not met.
6 2 - WID & Doors 2 Wide Size Chart 2 - WID 2, 3 & 4 WID CHAT Page of 2 /2" = '-0" Overall basic unit widths are calculated with vertical /2" mull. & OUGH OPNING. SIZ ( & HIGHT) &.O. SIZ ( & HIGHT) 24 x 30-2W 47.50" x 29.50" 42 x 30-2W 83.50" x 29.50" 24 x 36-2W 47.50" x 35.50" 42 x 36-2W 83.50" x 35.50" 24 x 42-2W 47.50" x 4.50" 42 x 42-2W 83.50" x 4.50" 24 x 48-2W 47.50" x 47.50" 42 x 48-2W 83.50" x 47.50" 24 x 54-2W 47.50" x 53.50" 42 x 54-2W 83.50" x 53.50" 24 x 60-2W 47.50" x 59.50" 42 x 60-2W 83.50" x 59.50" 24 x 66-2W 47.50" x 65.50" 42 x 66-2W 83.50" x 65.50" 24 x 72-2W 47.50" x 7.50" 42 x 72-2W 83.50" x 7.50" 24 x 78-2W 47.50" x 77.50" 42 x 78-2W 83.50" x 77.50" & OUGH OPNING. SIZ ( & HIGHT) &.O. SIZ ( & HIGHT) 30 x 30-2W 59.50" x 29.50" 48 x 30-2W 95.50" x 29.50" 30 x 36-2W 59.50" x 35.50" 48 x 36-2W 95.50" x 35.50" 30 x 42-2W 59.50" x 4.50" 48 x 42-2W 95.50" x 4.50" 30 x 48-2W 59.50" x 47.50" 48 x 48-2W 95.50" x 47.50" 30 x 54-2W 59.50" x 53.50" 48 x 54-2W 95.50" x 53.50" 30 x 60-2W 59.50" x 59.50" 48 x 60-2W 95.50" x 59.50" 30 x 66-2W 59.50" x 65.50" 48 x 66-2W 95.50" x 65.50" 30 x 72-2W 59.50" x 7.50" 48 x 72-2W 95.50" x 7.50" 30 x 78-2W 59.50" x 77.50" 48 x 78-2W 95.50" x 77.50" & OUGH OPNING. SIZ ( & HIGHT) 36 x 30-2W 7.50" x 29.50" 36 x 36-2W 7.50" x 35.50" 36 x 42-2W 7.50" x 4.50" 36 x 48-2W 7.50" x 47.50" 36 x 54-2W 7.50" x 53.50" 36 x 60-2W 7.50" x 59.50" 36 x 66-2W 7.50" x 65.50" 36 x 72-2W 7.50" x 7.50" 36 x 78-2W 7.50" x 77.50" ** Calculations based on 82 /2" header height. meets gress
7 3 - WID & Doors 3 Wide Size Chart 3 - WID 2, 3 & 4 WID CHAT Page 2 of 2 /2" = '-0" Overall basic unit widths are calculated with vertical /2" mull. & OUGH OPNING. SIZ ( & HIGHT) &.O. SIZ ( & HIGHT) 24 x 30-3W 7.50" x 29.50" 42 x 30-3W 25.50" x 29.50" 24 x 36-3W 7.50" x 35.50" 42 x 36-3W 25.50" x 35.50" 24 x 42-3W 7.50" x 4.50" 42 x 42-3W 25.50" x 4.50" 24 x 48-3W 7.50" x 47.50" 42 x 48-3W 25.50" x 47.50" 24 x 54-3W 7.50" x 53.50" 42 x 54-3W 25.50" x 53.50" 24 x 60-3W 7.50" x 59.50" 42 x 60-3W 25.50" x 59.50" 24 x 66-3W 7.50" x 65.50" 42 x 66-3W 25.50" x 65.50" 24 x 72-3W 7.50" x 7.50" 42 x 72-3W 25.50" x 7.50" 24 x 78-3W 7.50" x 77.50" 42 x 78-3W 25.50" x 77.50" & OUGH OPNING. SIZ ( & HIGHT) &.O. SIZ ( & HIGHT) 30 x 30-3W 89.50" x 29.50" 48 x 30-3W 43.50" x 29.50" 30 x 36-3W 89.50" x 35.50" 48 x 36-3W 43.50" x 35.50" 30 x 42-3W 89.50" x 4.50" 48 x 42-3W 43.50" x 4.50" 30 x 48-3W 89.50" x 47.50" 48 x 48-3W 43.50" x 47.50" 30 x 54-3W 89.50" x 53.50" 48 x 54-3W 43.50" x 53.50" 30 x 60-3W 89.50" x 59.50" 48 x 60-3W 43.50" x 59.50" 30 x 66-3W 89.50" x 65.50" 48 x 66-3W 43.50" x 65.50" 30 x 72-3W 89.50" x 7.50" 48 x 72-3W 43.50" x 7.50" 30 x 78-3W 89.50" x 77.50" 48 x 78-3W 43.50" x 77.50" & OUGH OPNING. SIZ ( & HIGHT) 36 x 30-3W 07.50" x 29.50" 36 x 36-3W 07.50" x 35.50" 36 x 42-3W 07.50" x 4.50" 36 x 48-3W 07.50" x 47.50" 36 x 54-3W 07.50" x 53.50" 36 x 60-3W 36 x 66-3W 36 x 72-3W 36 x 78-3W 07.50" x 59.50" 07.50" x 65.50" 07.50" x 7.50" 07.50" x 77.50" ** Calculations based on 82 /2" header height. meets gress
8 levations Page of 5 /2" = '-0" X30 30X30 36X30 42X30 48X30 30 HIGHT.O. HIGHT B.U. HIGHT.O. HIGHT B.U. HIGHT.O. HIGHT B.U. HIGHT.O. HIGHT B.U. HIGHT.O. HIGHT B.U. HIGHT 23 /2" B.U. B.U. B.U..O..O..O. OUGH OPNING OUGH OPNING 24X36 30X36 36X36 42X36 48X36 36 HIGHT.O. HIGHT B.U. HIGHT.O. HIGHT B.U. HIGHT.O. HIGHT B.U. HIGHT.O. HIGHT B.U. HIGHT.O. HIGHT B.U. HIGHT 23 /2" B.U. B.U. B.U..O..O..O. OUGH OPNING OUGH OPNING
9 42 HIGHT 48 HIGHT OUGH OPNING HIGHT HIGHT OUGH OPNING HIGHT HIGHT & Doors X42 30X42 23 /2" B.U. B.U..O..O. 23 /2" B.U. B.U..O..O. OUGH OPNING HIGHT 24X48 HIGHT 30X48 OUGH OPNING HIGHT HIGHT OUGH OPNING HIGHT OUGH OPNING HIGHT X42 42X42 B.U..O. OUGH OPNING 36X48 42X48 B.U..O. OUGH OPNING HIGHT OUGH OPNING HIGHT HIGHT HIGHT OUGH OPNING HIGHT HIGHT levations Page 2 of 5 /2" = '-0" 48 48X42 OUGH OPNING 48X48 OUGH OPNING OUGH OPNING HIGHT HIGHT OUGH OPNING HIGHT HIGHT
10 HIGHT 24X54 23 /2" B.U. 60 HIGHT 54" OUGH OPNING HIGHT 53 /2" HIGHT 30X54 B.U..O..O. 23 /2" B.U..O. 60" OUGH OPNING HIGHT 59 /2" HIGHT 24X60 30X60 B.U..O. gress: Will Meet gress 60" OUGH OPNING HIGHT 59 /2" HIGHT 54" OUGH OPNING HIGHT 53 /2" HIGHT 60" OUGH OPNING HIGHT 54" OUGH OPNING HIGHT X54 42X54 B.U..O. OUGH OPNING 36X60 B.U..O. 42X60 OUGH OPNING 59 /2" HIGHT 60" OUGH OPNING HIGHT 59 /2" HIGHT 53 /2" HIGHT 54" OUGH OPNING HIGHT 53 /2" HIGHT levations Page 3 of 5 /2" = '-0" 48 48X54 OUGH OPNING 48X60 OUGH OPNING 59 /2" HIGHT 60" OUGH OPNING HIGHT 54" OUGH OPNING HIGHT 53 /2" HIGHT
11 66 HIGHT 72 HIGHT gress: Will Meet gress 72" OUGH OPNING HIGHT 7 /2" HIGHT 66" OUGH OPNING HIGHT 65 /2" HIGHT & Doors X66 30X66 23 /2" B.U. B.U..O..O. 23 /2" B.U. B.U..O..O. 72" OUGH OPNING HIGHT 24X72 7 /2" HIGHT 66" OUGH OPNING HIGHT 65 /2" HIGHT 72" OUGH OPNING HIGHT 66" OUGH OPNING HIGHT X66 42X66 B.U..O. OUGH OPNING 36X72 B.U..O. 42X72 OUGH OPNING 7 /2" HIGHT 72" OUGH OPNING HIGHT 7 /2" HIGHT 32 9/6" DLO 65 /2" HIGHT 66" OUGH OPNING HIGHT 65 /2" HIGHT levations Page 4 of 5 /2" = '-0" 48 48X66 OUGH OPNING 48X72 OUGH OPNING 72" OUGH OPNING HIGHT 7 /2" HIGHT 66" OUGH OPNING HIGHT 65 /2" HIGHT
12 levations Page 5 of 5 /2" = '-0" HIGHT 78" OUGH OPNING HIGHT 77 /2" HIGHT 24X78 78" OUGH OPNING HIGHT 77 /2" HIGHT 30X78 78" OUGH OPNING HIGHT 77 /2" HIGHT 36X78 78" OUGH OPNING HIGHT 77 /2" HIGHT 42X78 78" OUGH OPNING HIGHT 77 /2" HIGHT 48X78 23 /2" B.U. B.U. B.U..O..O..O. OUGH OPNING OUGH OPNING gress: Will Meet gress
Casement/Awning Window Parts Reference Catalog
Casement/Awning Window Parts Reference Catalog (Includes Miscellaneous Parts for Eyebrow Casement and Garden Bay Windows) #1028654 (Revised 03/02) Weather Shield Mfg., Inc. Medford, WI 54451 715/748-2100
SIZE TABLES Wood and Aluminum-Clad Exteriors Double- and Single-Hung
Double- and Single-Hung Left Right Springline Arch Head Partial Arch Head Pella Architect Series single-hung windows are available in shapes shown above, and additional custom shapes per drawing. For specifications,
MINNESOTA DEPARTMENT OF PUBLIC SAFETY State Fire Marshal Division STATEMENT OF POLICY. State Fire Marshal
MINNESOTA DEPARTMENT OF PUBLIC SAFETY State Fire Marshal Division STATEMENT OF POLICY Policy #: Subject of Policy: INS-04 (2007) Escape Windows Revised and Approved By: Title: Jerry Rosendahl State Fire
Eagle Talon RetroFit Double-Hung and Picture Window Measuring Guidelines
Eagle Talon RetroFit and To assist you with measuring for Eagle Talon RetroFit products, we ve included typical section details of double-hung products comparable to what may be in your home. Please read
Sample Calculations...V-CR-12. Door and Window Typical Combinations... V-CR-12 Horizontal and Vertical Typical Combinations...
SECTION DIRECTORY General Information Definitions...V-CR- Design Considerations...V-CR- Composite Configurations...V-CR-4 Design Considerations and Examples for Typical Window and Door Combinations...V-CR-5
How to Measure for Exterior Shutters
Tools you may need: Measuring Tape Pencil Paper Ladder How to Measure for Exterior Shutters Measuring your windows properly is an important step to ensure your installation goes both smoothly and that
Introduction...COMB-2 Design Considerations and Examples...COMB-3
SECTION DIRECTORY General Information Introduction...COMB-2 Design Considerations and Examples...COMB-3 Combination Assembly Recommendations and Limitations Composite Configurations...COMB-4 Typical Sealant
Basic Math for the Small Public Water Systems Operator
Basic Math for the Small Public Water Systems Operator Small Public Water Systems Technology Assistance Center Penn State Harrisburg Introduction Area In this module we will learn how to calculate the
This handout is a guide only and does not contain all of the requirements of the Minnesota State Building Code or city ordinances.
Basement Finishing Guide Community Development Department Building Inspections Division 5200 85 th Avenue North / Brooklyn Park, MN 55443 Phone: (763) 488-6379 / Fax: (763) 493-8171 6/15 www.brooklynpark.org
Gliding Windows Premium Vinyl
TABL OF CONTNTS Product Specifications... 6-2 QuickSpecGuide... 6-3 levations/sizes: 1/4 Scale 2 Wide Gliding Window... 6-4 3 Wide Gliding Window... 6-8 SashGlazingOptions:3 Scale... 6-10 Grilles & SDL
Development Services Department Building Permit & Inspection Services Shed and Garage Construction Guide for Detached and Semi-Detached Dwellings
Development Services Department Building Permit & Inspection Services Shed and Garage Construction Guide for Detached and Semi-Detached Dwellings H:/forms/handouts/bldg071.docx Shed and Garage Construction
WINDOW AND DOOR REPLACEMENT REQUIREMENTS
WINDOW AND DOOR REPLACEMENT REQUIREMENTS Should you have any questions after reading the following information, please call the Building Inspection Department at 651-439-4439 to discuss the topics of concern.
RESIDENTIAL WINDOW REPLACEMENT
3S258 MANNING AVENUE WARRENVILLE, IL 60555 PH: 630.393.9050 FAX 630.393.1531 RESIDENTIAL WINDOW REPLACEMENT A building permit is required for the installation or replacement of windows in a residence.
City of Glendale Window Replacement Information and Submittal Requirements
City of Glendale Window Replacement Information and Submittal Requirements General Information Do not buy or install any windows before you get a permit! A building permit is required for all window replacements
Area and Perimeter. Name: Class: Date: Short Answer
Name: Class: Date: ID: A Area and Perimeter Short Answer 1. The squares on this grid are 1 centimeter long and 1 centimeter wide. Outline two different figures with an area of 12 square centimeters and
How To Build A Basement House
Single Family Basement Finish Purpose of Guide The purpose of this guide is to assist you in the permit process for your project. This handout is intended as a basic plan submittal under the 2009 International
The replacement or modification of existing windows shall comply with the following requirements:
City of La Habra Heights Building Division 1245 N. Hacienda Road La Habra Heights, CA 90631 Office: (562) 694-6302 ext. 228 Fax: (562) 690-5010 WINDOW REPLACEMENT 2010 CALIFORNIA RESIDENTIAL CODE (CRC)
BUILDING PERMIT APPLICATION
MASON COUNTY PERMIT NO. DEPARTMENT OF COMMUNITY DEVELOPMENT BUILDING PLANNING FIRE MARSHAL WWW.CO.MASON.WA.US (360) 427-9670 Shelton ext.352 Mason County Bldg. III, 426 West Cedar Street (360) 275-4467
Cable Tray Selection-
Cable Selection- For allowable cable types see the Appendix page A-9. The following guidelines are based on the 2002 National Electrical Code, Article 392. I) Number of Multiconductor Cables rated 2000
A site plan or floor plan clearly identifying the location(s) of all new replacement window(s)
WINDOW REPLACEMENT GUIDELINES Community Development Planning & Building 2263 Santa Clara Ave., Rm. 190 Alameda, CA 94501-4477 alamedaca.gov 510.747.6800 F: 510.865.4053 TDD: 510.522.7538 Hours: 7:30 a.m.
Quality Building Products for over 50 Years
Light Commercial Quality Building Products for over 50 Years Harvey Building Products is a leading manufacturer and distributor of high quality building products. We manufacture a complete line of superior
6' 7-1/2" SIZE TABLES Aluminum-Clad Exterior
6' 7-1/2" SIZE TABLES 2' 7 1/ 2" (800) 3' 1 1/ 2" 2' 6 3 / 4" (781) 3' 0 3 / 4" (953) 4' 1 1/ 2" (1 257) (933) 4' 0 3 / 4" (1 238) 3180 3780 4980 5' 0" 4' 11 (1 524) 6' 0" (1 505) 5' 11 (1 829) 8' 0" (2
4. ANCHOR BOLTS AND STRAPS a. ½" anchor bolts shall be embedded 7" into concrete a maximum of 6' on center and 12" from corners and ends of plates.
GENERAL CODE REQUIREMENTS (BASEMENTS) 1. FOOTINGS a. Footings shall be below frost line depth (42"). b. For an 8" foundation wall, footings shall be no less than 8" deep and 16" wide. c. Steel reinforcement
Vinyl Greenhouse Window Page 2 of 6 New Contruction Installation Instructions
New Construction Installation Instructions EPLACEMENT Installation Instructions Page 2 of 6 New Contruction Installation Instructions 1. Frame rough opening equal to window call out size. ough opening
Residential Accessory Buildings
City of Republic Residential Accessory Buildings REVISION DATE: FEBRUARY 2012 Buildings less than 120 square feet (120 sq. ft.) do not require a building permit unless they: are built on a permanent concrete
Aluminium systems profile selection
Aluminium systems profile selection The purpose of this document is to summarise the way that aluminium profile selection should be made, based on the strength requirements for each application. Curtain
DE Frame with C Series Sidelight
TOOLS REQUIRED Tape measure 6' magnetic level 3' magnetic level Screw gun with clutch adjusted #2 phillips tip #3 phillips tip Screwdriver (used to adjust frame on will using oval slots) Pry Bar Powder
Glossary. 1/3 1/3 1/3 - Configuration of a vent-fixed-vent (xox) window in which the vents and fixed panel are equal sizes
Glossary 1/3 1/3 1/3 - Configuration of a vent-fixed-vent (xox) window in which the vents and fixed panel are equal sizes 1/4 1/2 1/4 - Configuration of a vent-fixed-vent (xox) window in which the vents
Lower Level (Level L) Exhibit Halls A, B & C
Floor Plans Wal t e r E. Was h i n g ton Con v e n t i on C e n t e r Lower Level (Level L) Exhibit Halls A, B & C Lower Level (Level L) Lower Level (Level L) Halls A, B & C Hall A 151,000 square feet
INSTALLATION INSTRUCTIONS for Vinyl Windows without Nailing Fin (JII011) ImPOrTANT INFOrmATION & GlOssAry. rough OPeNINGs
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for vinyl windows without a nailing fin (including finless, flush fin and flange). Read these instructions
INSTALLATION INSTRUCTIONS for Vinyl Windows with Integral Nailing Fin (JII001)
Thank you for selecting JELD-WEN products. Attached are JELD-WEN s recommended installation instructions for Vinyl windows with an integral nailing fin. While the use of these installation instructions
MAJOR 2015 MN RESIDENTIAL CODE CHANGES Effective Date: January 24 th, 2015
MAJOR 2015 MN RESIDENTIAL CODE CHANGES Effective Date: January 24 th, 2015 **Disclaimer: This document is to serve as informational purposes only. This is not a code book or a final interpretation of the
2015 UCC Residential Code Update
2015 UCC Residential Code Update The Pennsylvania regulations related to Residential Construction codes changed effective January 1, 2016. The sections of the 2015 IRC that PA adopted as part of the UCC
Below are detailed instructions for using the EMS load calculator.
Introduction The EMS load calculator is designed to make load calculating as painless as possible. For sizing the equipment, only the first three tabs (Steps 1, 2 & 3) need to be completed. This process
Mobile Home Pre-Inspection Checklist
Mobile Home Pre-Inspection Checklist TWO (2) STEP INSPECTION PROCESS STEP ONE: CALL FOR THE FIRST INSPECTION WHEN THESE ITEMS ARE COMPLETE. 1. Septic tank installed and plumbing complete. (SEE PLUMBING
EXHIBIT/BOOTH SPECIFICATIONS
BOOTH SPECIFICATIONS Please review the following booth specifications to ensure that your display meets the Exhibit/Booth Guidelines. All booths, regardless of size, are required to follow these guidelines.
Cast Iron Radiator Heating Capacity Guide
Columbia Heating Products Company 1409 Rome Rd Baltimore, Maryland 21227 410-242-5300 Toll Free 800-645-7845 www.columbiaheating.com Use this handy guide to determine how much heat existing "old style"
Florida Building Code 2004 SECTION 1009 STAIRWAYS AND HANDRAILS
Florida Building Code 2004 SECTION 1009 STAIRWAYS AND HANDRAILS 1009.1 Stairway width. The width of stairways shall be determined as specified in Section 1005.1, but such width shall not be less than 44
BUILDING PERMIT SPECIFICATIONS
BUILDING PERMIT SPECIFICATIONS The below noted requirements are based upon La Plata County Building Code. These specifications are not intended as a complete set of requirements, but are intended to provide
Exhaust Calculation Booklet
Exhaust Calculation Booklet American Dryer Corporation 88 Currant Road Fall River MA 02720-4781 Telephone: (508) 678-9000 / Fax: (508) 678-9447 e-mail: [email protected] ADC Part No. 450450 Exhaust
Sash Replacement Guide
for Andersen 200/400 Series Awning Windows Read all instructions carefully before attempting this procedure. If you have any questions about your ability to complete this procedure, call Andersen at 1-888-888-7020
glass & Glazing Products
glass & Glazing Products WallMaker Create an unlimited variety of bright, beautiful and secure interior environments with the easy-to-install Stylmark WallMaker glass wall system. This versatile system
Dimensioning and Estimating Brick Masonry
TECHNICAL NOTES on Brick Construction 1850 Centennial Park Drive, Reston, Virginia 20191 www.gobrick.com 703-620-0010 10 February 2009 Dimensioning and Estimating Brick Masonry Abstract: This Technical
BOOTH DESIGN RULES NEW! [email protected]
BOOTH DESIGN RULES All exhibits must conform to the dimensions outlined below in order to assure ease of movement of participants and clear lines of visibility in the exhibit hall. For more information
VILLAGE OF HUDSON FALLS 220 MAIN STREET HUDSON FALLS, NY 12839 (518) 747-5426 /
John E. Barton Mayor Ellen M. Brayman Clerk/Treasurer VILLAGE OF HUDSON FALLS 220 MAIN STREET HUDSON FALLS, NY 12839 (518) 747-5426 / Trustees: James Gallagher Robert Cook Michael Horrigan Thomas VanAernem
Vestibule Case Study. Vestibule Requirement Intent [2003 IECC, 2006 IECC, 2003 IBC, 2006 IBC, 90.1-2001, 90.1-2004]
![Vestibule Case Study. Vestibule Requirement Intent [2003 IECC, 2006 IECC, 2003 IBC, 2006 IBC, 90.1-2001, 90.1-2004]](/thumbs/24/2939769.jpg "Vestibule Case Study. Vestibule Requirement Intent [2003 IECC, 2006 IECC, 2003 IBC, 2006 IBC, 90.1-2001, 90.1-2004]")
Vestibule Case Study [2003 IECC, 2006 IECC, 2003 IBC, 2006 IBC, 90.1-2001, 90.1-2004] Vestibule Requirement Intent Page 1 of 14 The primary intent behind the requirement for a vestibule is to reduce infiltration
SPCC Plan - Calculation Guidance
SPCC Plan - Calculation Guidance The following example compares two different design criteria: one based on the volume of the tank and one based on precipitation. Scenario: A 20,000-gallon horizontal tank
Section A Roof Truss
Section A Roof Truss Truss Types Wisconsin Truss, Inc. can build a variety of truss types, pictured below are some common examples. Common Bobtail Scissor Mono Studio Dual Slope Cathedral Tray Vault Parallel
INSTALLATION INSTRUCTIONS
door frames Engineered product systems INSTALLATION INSTRUCTIONS door frames MINIMALIST DOOR FRAME Fry Reglet Flush Door frames are designed for use with 3 5/8 studs with ½ drywall both sides (4 5/8 throat
THIRD LAGUNA HILLS MUTUAL
THIRD LAGUNA HILLS MUTUAL SECTION 34 WINDOWS & WINDOW ATTACHMENTS MAY 1996, RESOLUTION M3-96-28 SEPTEMBER 2002, RESOLUTION M3-02-47 NOVEMBER 2002, RESOLUTION M3-02-62 OCTOBER 2004, RESOLUTION 03-04-27
BLADE S-MAX Cabinet for Blade Server
Cabinet for Blade Server 1 2 Overview Material specification Corner verticals: 1.5 mm steel End frames: 1.5 mm steel Panel mounts: 2.0 mm steel Panel mount supports: 1.5 mm steel Side panels, door and
CITY OF FAIRFAX CODE ADMINISTRATION 703-385-7830 / FAX 703-385-9265 www.fairfaxva.gov
CITY OF FAIRFAX CODE ADMINISTRATION 703-385-7830 / FAX 703-385-9265 www.fairfaxva.gov Finishing a basement to make additional living space in a house is a popular construction project for many homeowners.
POST AND FRAME STRUCTURES (Pole Barns)
POST AND FRAME STRUCTURES (Pole Barns) Post and frame structures. The following requirements serve as minimum standards for post and frame structures within all of the following structural limitations:
InsulView Window Installation Instructions
InsulView Window Installation Instructions 1. The entire building is normally sheeted with the 2" 2 ½ OR 3 wall panel and the windows installed at a later time. A window retrofit of an existing building
H:\forms\handouts\bldg049 1 of 11 Revised Mar 2/15/dh
Accessory Apartment Construction Guide For Single Detached Dwelling and Semi-Detached Dwellings that have been in existence for at least five (5) years Notes: Buildings that are less than five (5) years
INSTALLATION INSTRUCTIONS for Premium Pocket Windows (JII022) IMPoRtaNt INFoRMatIoN & glossary. safety & HaNdlINg
Thank you for selecting JeLd-weN products. Attached are JeLd-weN s recommended installation instructions for pocket (replacement) double-hung, casement, awning, picture or transom windows, designed to
Residential Plan Review Emergency Vehicle Access and Water Supply Permit Information Packet
Residential Plan Review Emergency Vehicle Access and Water Supply Permit Information Packet 1. Definitions a. AHJ Authority Having Jurisdiction. The Fire Chief or Fire Marshal of a given Fire District
Size & Range. for windows & doors. Company
Size & Range for windows & doors A Company B General information windows and doors Sizes This catalogue contains all Airlite s standard sizes for windows and doors. These are the ones that we make every
OCFRD TENT STANDARD 6000. This Standard operates under the authority of Orange County, Florida Ordinance and State Statutes.
1. Authority Orange County Fire Rescue Department Tents & Membrane Structures Office of The Fire Marshall - 109 E. Church Street, Lower Level - Orlando, Florida 32801-3319 Phone: 407-836-0004 Fax: 407-836-8310
DRYER VENTING SPECIFICATIONS DRYER SAFETY
DRYER VENTING SPECIFICATIONS Table of Contents DRYER SAFETY...1 INSTALLATION REQUIREMENTS...4 Venting Requirements...5 DRYER INSPECTION AND CLEANING...7 Frequency of Exhaust System Cleaning...7 Inspecting
Installation Detailed installation instructions are provided which should be strictly followed.
Specification System 6 The Metal Technology Thermally-Broken Vertical Slide Window has been designed in such a way that its'attractive and clean lines will enhance all types of residential and commercial
Free 12 x 8 Shed Plan With Illustrations, Blueprints & Step By Step Details
Free 12 x 8 Shed Plan With Illustrations, Blueprints & Step By Step Details Brought To You By: MyShedPlans Click Here To Download 12,000 Shed Plans >> 12 x 8 Basic Shed This 8 12-ft. shed features a simple
Custom 30 x 20-8 Garage Plan Plan #g233 By SDS-CAD Specialized Design Systems
P O Box 34 Mendon, Utah Custom 30 x 20-8 Garage Plan Plan #g233 By Page 1 Title Page Page 2 Main Floor Plan Page 3 Foundation Plan Page 4 Elevation Views Page 5 Framing and Details Page 6 Typical Section
Index 20010 Series Prestressed Florida-I Beams (Rev. 07/12)
Index 20010 Series Prestressed Florida-I Beams (Rev. 07/12) Design Criteria AASHTO LRFD Bridge Design Specifications, 6th Edition; Structures Detailing Manual (SDM); Structures Design Guidelines (SDG)
HYDRAULIC FREIGHT ELEVATOR PACKAGES
HYRAULIC FRIGHT LVATOR PACKAGS Leistritz offers its customers a complete selection of freight elevators to meet a wide range of heavy-duty, freight handling applications. In addition to the cylinders,
Roof Tutorial. Chapter 3:
Chapter 3: Roof Tutorial The majority of Roof Tutorial describes some common roof styles that can be created using settings in the Wall Specification dialog and can be completed independent of the other
Impact-Resistant Windows and Sliding Glass Doors
Impact-Resistant Windows and Sliding Glass Doors Make Your Home A SafeHarbor. SafeHarbor Impact-Resistant Windows and Sliding Glass Doors are designed to look like traditional windows and doors, but they
BASIC FIRE DOOR REQUIREMENTS TECHNICAL DATA SHEET NO. 401
BASIC FIRE DOOR REQUIREMENTS SHEET NO. 401 Fire door openings are classified by their locations in the building. The location determines the length of exposure protection required, based on the potential
HS-901(A) BASIC STEAM HEATING SYSTEMS
HS-901(A) BASIC HEATING SYSTEMS One-Pipe Two-Pipe Basic Steam Heating Systems One-pipe steam heating system EQUALIZER SAFETY FACTOR STATIC HEAD PRESSURE DROP 2" HEATING UNIT 15" DRIP CONNECTION In a one-pipe,
Important Information for Installer & Homeowner
Important Information for Installer & Homeowner Homeowner: Please keep this information for your records, do not discard! Installation Instructions for Wood Frame Construction Replacement (See other side
Grade 5 Work Sta on Perimeter, Area, Volume
Grade 5 Work Sta on Perimeter, Area, Volume #ThankATeacher #TeacherDay #TeacherApprecia onweek 6. 12. Folder tab label: RC 3 TEKS 5(4)(H) Perimeter, Area, and Volume Cover: Reporting Category 3 Geometry
Number of Sides Required to Have a Handrail
Excerpt from 2012 B.C. Building Code HANDRAILS & GUARDS 9.8.7. Handrails 9.8.7.1. Required Handrails 1) Except as provided in Sentences (2) to (4), handrails shall be installed on stairs and ramps in accordance
Flexivent Windows (1952 to 1979)
Flexivent Windows (1952 to 1979) Parts Catalog Main Menu Section TOC Search What s in This Section Standard Windows................................................ Page 3 Parts Illustration...........................................................
INSTALLATION INSTRUCTIONS IMPERVIA (Vent and Fixed) AWNING, CASEMENT, and LARGE AWNING WINDOW WITH FINS
2009 Pella Corporation INSTALLATION INSTRUCTIONS IMPERVIA (Vent and Fixed) AWNING, CASEMENT, and LARGE AWNING WINDOW WITH FINS Part Number: 80WH0100 Installation Instructions for Typical Wood Frame Construction.
Neighborhood Business. Neighborhood Mixed Use. Community Business. Factoria Land Use District 1 2A 2A 2A 30 (23) 15 (23) 30 (23) 30 (23)
20.20.010 s in land use distris dimensional requirements. Chart 20.20.010 s in land use distris Dimensional Requirements STD LAD USE CODE REF LAD USE CLASSIFICATIO Professional / 2 Light Industry General
NFIP LOWEST FLOOR GUIDE ABRIDGED
NFIP LOWEST FLOOR GUIDE ABRIDGED National Flood Insurance Program SCROLL DOWN 1 NFIP LOWEST FLOOR GUIDE QUICK REFERENCE This is an abridged version of the 2013 Flood Insurance Manual Lowest Floor Guide.
NC Rehab Code Case Study Cheerwine Building January 17, 2002; rev 4/12/02
NC Rehab Code Case Study Cheerwine Building January 17, 2002; rev 4/12/02 PART A: Project Data and Classification 1. Project name & location Renovation of the Cheerwine Building, 322 East Council St.,
Bath Planning Guidelines With Access Standards
Bath Planning Guidelines With s 1: Door/Entry The clear opening of a doorway should be at least 32. This would require a minimum 2-10 door. If the existing structure precludes changing the opening then
SECTION REFERENCE. Awning Windows. Casement & 400 Series
400 Series Casement & Awning Windows SECTION REFERENCE Alignment Grid...38 39 Tables of Sizes...40 44 Opening Specifi cations...45 48 Divided Light Patterns... 50 Window Details... 51 52 Joining Details...
Building Department John Fiedler Construction Official Ext. 211. SAMPLE GUIDE FOR 1&2 FAMILY DWELLING BASEMENTS Rev 4-3-2014
TOWNSHIP OF HILLSBOROUGH COUNTY OF SOMERSET Hillsborough Township Municipal Complex The Peter J. Biondi Building 379 South Branch Road Hillsborough, NJ 08844 P: (908) 369-4313 F: (908) 369-3954 Building
Single Family Residential Building Permit Questions & Answers
Single Family Residential Building Permit Questions & Answers Prepared by Dept. of Public Works Revised 07/01/13 200 East Park Street Edwardsville, IL 62025 (618) 692-7535 (618) 692-7505(Fax) Hours: Monday
Single Family Residential Basement Finish
How to Use This Guide Building Guide Pottawattamie County Planning & Development Department Building & Safety Division Single Family Residential Basement Finish Provide two (2) sets of plans and complete
TEST REPORT. Report No.: B3404.01-801-47. Rendered to: CROFT, LLC. Magnolia, Mississippi. PRODUCT TYPE: Aluminum Single Hung Window SERIES/MODEL: 95
Architectural Testing TEST REPORT Report No.: B3404.01-801-47 Rendered to: CROFT, LLC. Magnolia, Mississippi PRODUCT TYPE: Aluminum Single Hung Window SERIES/MODEL: 95 SPECIFICATION: AAMA/WDMA/CSA 101/I.S.2/A440-08,
PERFORMANCE TEST REPORT
PERFORMANCE TEST REPORT CCLW JOB #08-5152-1 DATES OF FORMAL TESTING SEPTEMBER 19 & 23, 2008 TEST LOCATION CONSTRUCTION CONSULTING LABORATORY WEST 4751 WEST STATE STREET, SUITE B ONTARIO, CA 91762 PH: 909-591-1789
STORAGE SPACE EFFICIENCY GUIDE A DEMONSTRATION IN SPACE
STORAGE SPACE EFFICIENCY GUIDE A DEMONSTRATION IN SPACE SAVING SPACE IS JUST THE BEGINNING Maximizing the efficiency and productivity of a facility is no simple task. With so many variables constantly
COMMONLY USED RESIDENTIAL BUILDING CODES
COMMONLY USED RESIDENTIAL BUILDING CODES INTERNATIONAL RESIDENTIAL CODE (2009) form revised 5/10 STAIRWAYS 46. LANDINGS. Section R311 IRC 2009 R311.7.5 Landings for stairways. There shall be a floor or
Ch. 58 DIVISION D-O 34 CHAPTER 58. DIVISION D-O ORDINARY COMMERCIAL, INDUSTRIAL, OFFICE OCCUPANCY GROUP CONSTRUCTION TYPE MAXIMUM STORY HEIGHT
Ch. 58 DIVISION D-O 34 CHAPTER 58. DIVISION D-O ORDINARY COMMERCIAL, INDUSTRIAL, OFFICE Sec. 58.1. Division D-O occupancies. 58.2. Separation and mixed occupancy. OCCUPANCY GROUP CONSTRUCTION TYPE MAXIMUM
Replacement Window Installation Guide Non-Impact & Impact Resistant Windows without Nailing Fin
Replacement Window Installation Guide Non-Impact & Impact Resistant Windows without Nailing Fin americancraftsmanwindows.com Project Requirements: Failure to follow these instructions may void product
Tundra Series Windows January 2016
Tundra Series Windows January 2016 New Construction Installation Instructions Nail Fin, J-Fin and Brickmold Aplications product. ATTENTION! Read and understand all installation instructions before installing
REHABILITATION OF MOBILE HOMES R4 34 606
REHABILITATION OF MOBILE HOMES R4 34 606 PURPOSE The purpose of this program is to provide minimum safety standards for homes manufactured before the implementation of the HUD Manufactured Home Construction
PRODUCT GUIDE Aluminum Single-Hung Windows (JPG002)
This guide contains procedures for common user serviceable repair tasks found on aluminum single-hung windows. If a condition arises that is not covered in this guide, please contact us for professional
GUIDELINES FOR REHABILITATION OF TRADITIONAL COMMERCIAL BUILDINGS DESIGN GUIDELINES
GUIDELINES FOR REHABILITATION OF TRADITIONAL COMMERCIAL BUILDINGS DESIGN GUIDELINES PAGE 13 DESIGN GUIDELINES The following design guidelines have been developed to guide appropriate design in the Downtown
Residential Decks. Planning and Development Services Department
Building Safety Division 8500 Santa Fe Drive Overland Park, KS 66212 (913) 895-6225 Fax (913) 895-5016 Email: [email protected] Planning and Development Services Department Residential Decks
TEST REPORT. Rendered to: INTERNATIONAL WINDOW Hayward, California. PRODUCT TYPE: Aluminum Hopper SERIES/MODEL: 7222
Architectural Testing TEST REPORT Report No.: C2375.01-301-44 Rendered to: INTERNATIONAL WINDOW Hayward, California PRODUCT TYPE: Aluminum Hopper SERIES/MODEL: 7222 SPECIFICATIONS: AAMA/WDMA/CSA 101/I.S.2/A440-05,
INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION FOR DOUBLE-HUNG VENT REPLACEMENT WINDOW
Vinyl Windows and Doors Manufactured by Pella Corporation INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION FOR DOUBLE-HUNG VENT REPLACEMENT WINDOW Lea las instrucciones en español en el reverso.
HOW TO... Channel Window Balances
Take Out Clips Open HOW TO... Channel Window Balances Used On Single Or Double Hung Sash Balance Shown Installed In Jamb With Sash Removed Remove the sash stops. Close sash to expose take-out clips. Open
Calculating Perimeter
Calculating Perimeter and Area Formulas are equations used to make specific calculations. Common formulas (equations) include: P = 2l + 2w perimeter of a rectangle A = l + w area of a square or rectangle