RAPID DIAL TEST INDICATORS
|
|
- Jayson Hensley
- 7 years ago
- Views:
Transcription
1 RAPID DIAL TEST INDICATORS The Verdict Rapid presents the dial face inclined to the workpiece surface ensuring good visual accessibility obviating parallax error. Rapids incorporate a rear swivel spigot enabling use for centering without additional attachments. All models have dovetail clamping slides top and bottom. WORM MECHANISM Stylus Swivel spigot standard on all models 2.
2 DIAL TEST INDICATORS The Dual Reading Metrinch Answer to the Metric Conversion Problem Fitted with pear shaped contact point Clamping facilities by means of dovetail or end spigot Dial rotates for zero setting Automatic reversal movement Jewelled Stylus swivels through an arc of 180 o Hand travels in one direction Lever pivots are mounted in ball bearings Imperial instruments fitted with 1/4'' diameter spigot Swivel spigot incorporated in body Indicator body machined with dovetail to suit attachments 15/5010/4010, 15/5013 and 15/5050 Code 08/3001 with Automatic Reversal Movement Dual Reading Metrinch Direct reading Inch and Metric in either system WORM MECHANISM CALIBRATION AND INSPECTION SERVICE AVAILABLE 3.
3 DIAL TEST INDICATORS 4.
4 DIAL TEST INDICATORS T1, T2 and T3 indicators have a switch lever for reversing the direction of movement. Lever pivots are mounted in ball bearings. Fitted with 4mm or 1 /4'' dia.top spigot and holder body side clamp which accepts rods up to 6.5mm (0.256''). Indicator body machined with dovetail to suit attachments. T3 also supplied with a dovetail clamp. T2 T3 T6 and G Indicators are designed around the need for a long Stylus to overcome many measuring problems, supplied with round point only. T6 G T8 Dial Indicators incorporate an automatic reversal movement. Their rugged design and fine graduations provide maximum versatility for use in either the workshop or inspection department. Clamping facilities back and front by means of a dovetail and by a spigot at the top. Lever pivots are mounted in ball bearings. Dial rotates for zero setting Jewelled Stylus swivels through an arc of 180 o Hand travels in two directions without need of a reversible lever Swivel spigot incorporated in body Fitted with pear-shaped stylus which obviates the cosine error T8 The following features are incorporated as standard throughout Models A and C. Main bodies are machined from high quality brass Ratchet stylii are fitted and operated throughout an arc of 180 o A switch lever is fitted for reversing movement Dials are rotatable for zero setting The Supertest Indicators have a reversible screwed adaptor provided at the rear of the body for fitting direct to a surface gauge or similar stand. Dovetail Clamp, which also clamps on the Tubular Body, supplied as standard.designed for accurate indicating in machining layout or inspection applications. Accepts all standard holders and jig borer attachments. Jewelled Fully reversible Ratchet contact point swivels through 180 o Dial rotates for zero setting Furnished with Universal Holder, Body Clamp and two contact points in a form fitting case H WORM MECHANISM A Supertest CALIBRATION AND INSPECTION SERVICE AVAILABLE 5.
5 DIAL TEST INDICATORS Twin Indicator These indicators have been introduced to our range to simplify bore location and alignment when used in conjunction with a centering attachment. Designed with two dials set 180 o apart, it eliminates the use of a mirror; the pointers are attached to the same spindle hence identical readings are maintained over the full range. OPTIONAL EXTRA SWIVEL SPIGOT 15/ /4'' dia. 15/4017 4mm dia. Code No. Face Dial Reading Grad. Range Stylus Dia. Length 08/ 8010 Inch 1.125'' '' '' 0.780'' 08/ 8005 Metric 26.5mm 0.01mm mm 19.5mm Indicator Swivel Set Dial indicator ruggedly constructed to meet the demands of the workshop and inspection departments. The indicator is attached to a pot-magnet by means of a swivel ball and socket holder, enabling countless setting positions to be achieved. Shockproof, Ratchet Stylus mounting Dial rotates for zero setting Stylus swivels through an arc of 180 o Supplied complete with extra 0.25'' dia. spigot for use as an alternative method of fixing Code Model Dial Read. Grad. Range Stylus Dia. Length 10/ 7000 C 1'' '' '' 0.306'' 10/ 7001 Cmm 25mm 0.01mm mm 6.8mm Shop Set A combination set of the popular Model C Indicator, Dovetail Clamp, Minoring and a Collet Rod Attachment which can be utilised to meet almost every gauging application required in the workshop. Indicator Reading '' or 0.01mm. Each set is supplied in an instrument carton. Code: 18/2004 (inch) Code: 18/1004 (mm) 6.
6 DIAL TEST INDICATORS Code No: 23/2070 Code No: 23/2071 CALIBRATION AND INSPECTION SERVICE AVAILABLE 7.
7 INDICATOR SETS / RECESS INDICATOR Code No. for the set is : Imperial 18/ 2003 Metric 18/ / /
8 ANTIMAGNETIC DIAL TEST INDICATORS All materials are completely antimagnetic. Movement: independent unit (modern watches are made in the same way ). Not influenced by side pressure on instrument case. Readily interchangeable. Stylus support: adjustable ball-bearings which guarantee perfect stylus movement under all conditions. Reinforced flanges. Automatic reversal of measuring direction by means of double lever system. Accuracy : DIN 879/1 and BS 2795:1957/1971 Stylus can be displaced: Measuring force : max. 7oz (max. 20p ) Code No: Model: Dia. of dial Reading Range Length of stylus English 11/2020 T20 1.1'' '' 0.008'' 0.5'' 11/2021 T21 1,5'' '' 0.008'' 0.5'' Metric 11/1120 T20 28mm 0.002mm 0.2mm 12.5mm 11/1121 T21 38mm 0.002mm 0.2mm 12.5mm Spare Stylii for T20/T21 Point dia. 1mm 2mm 3mm Code No. 11/3001 (V95) 11/3006 (V96) 11/3011 (V97) Perpendicular Type Top mounted dial gives ease of reading when used for setting- up on jig bores, milling machines etc. Automatic reversal of measuring direction by means of a double lever system. Dovetails machined on three faces ensure secure and easy positioning. Completely antimagnetic: Monobloc design Accuracy: DIN 879/1 and BS 2795: 1957/1971 Code No: Model: Dia. of dial Reading Range Length of stylus 11/2022 T22 1.5'' '' 0.02'' 1.44'' 11/1022 T22 3.8mm 0.01mm 0.5mm 36.5mm Spare Stylii for T22 Point dia. 1mm Code No: 11/3016 (V98) CARBIDE ONLY CALIBRATION AND INSPECTION SERVICE AVAILABLE 9.
9 ATTACHMENTS AND ACCESSORIES 15/ / / / / / / / / / / / / /
10 SCREW-IN STYLII CALIBRATION AND INSPECTION SERVICE AVAILABLE 11.
11 SCREW-IN STYLII AND CONTACT POINTS 12.
12 CENTERING ATTACHMENTS 16/ / 0003 for / 2002 (1/4'' rod) MANUFACTURED BY VERDICT CALIBRATION AND INSPECTION SERVICE AVAILABLE 13.
13 CENTERING ATTACHMENTS DIACATOR FOR PRECISE CONCENTRICAL ALIGNING The DIACATOR is an instrument with a stationary indicator and a rotating probe for fast and accurate concentrical alignment of bores and shafts on most rotary machine tools. Applications: Concentrical alignment of boxes and shafts on milling, drilling and boring machines; Alignment of the footstock on milling and cylindrical grinding machines and of the tailstock on lathes; Accurate concentrical alignment of indexing heads and tables, of grinding fixtures, of drill sleeves in tool holders and of many other special fixtures. Design Features: The DIACATOR is mounted in two suspension ball bearings that render it entirely free from play. The probe yoke is provided with a safety clutch as a precaution against damage to the instrument should the probe hang up on some obstacle while in motion. Advantages: Contrary to other aligning methods, the machine is in motion during the aligning operation. Thus alignment takes place under the same conditions (uniform oil film on spindle bearings and constant speed) as the subsequent work. The dial remains stationary and is positioned to face the operator so that he may conveniently and accurately follow the process. During alignment the revolving probe and the working spindle form a single unit. Possible off centre of the tool chuck caused by an inaccurate chuck, closer, sleeve, etc, in no way influences the centering operation or its accuracy. Code No. 63/6000 Chucking Possibilities: 8mm and 3/8'', 1/2'' and 5/8'' draw-in collet chuck; three or four jaw chuck; inside Morse taper No.1. For larger inside tapers use standard taper sleeves. Specifications: Inside Diameter Range: 0.06'' to 4.72''(1.5 to 120mm) Outside Diameter Range: 0.04'' to 4.33''(1.0 to 110mm) Standard Set Includes: 1 Dial Indicator 1 Pendulum Probe 86''(22mm) (for small bores) 2 Off-set Probes 98'' and 1.89''(25 and 48mm) 1 Screw-on Morse Taper No.1 3 Screw-on Spacers 3/8'', 1/2''and 5/8''or 10,12 and 16mm (please specify choice when ordering) 1 Stop-rod 160mm long (6-1/4'') 1 Socket-head Wrench 0.08'' (2mm) 1 Hardwood Case 14.
YUASA MILLING MACHINE ACCESSORIES & TOOLS
97 HORIZONTAL / VERTICAL 5C COLLET INDEX 550 series 2 YEAR WARRANTY Spindle is manufactured with a taper seat in body frame. Rapid opening and closing is performed with a level collet closer with a leverage
More informationPrecision made in Europe. As per DIN 8606. The heart of a system, versatile and expandable.
1 von 9 Precision made in Europe. As per DIN 8606. The heart of a system, versatile and expandable. Main switch with auto-start protection and emergency off. Precision lathe chuck as per DIN 6386 (Ø 100mm).
More informationTOOL CLAMPING SYSTEMS
TOOL CLAMPING SYSTEMS 2015/2016 We work for customers who have a weakness for our strengths. Companies intent on making a difference are obliged to develop constantly as well as deploy their strengths
More informationOPTICAL MEASURING MACHINES
OPTICAL MEASURIN MACHINES SYLVAC SCAN Dedicated to the fast and contactless measuring of cylindrical parts, our new SCAN machines are based on the principle of the scanner. This technique allows to reproduce
More informationDUGARD. Machine Tools Since 1939. Dugard 700L Series Heavy Duty CNC Lathes. www.dugard.com
DUGARD Machine Tools Since 1939 Dugard 700L Series Heavy Duty CNC Lathes www.dugard.com Dugard 700L Heavy Duty CNC Lathe 2000, 3000 or 4000mm bed length Designed for easy and convenient operation The concave
More informationThe Bonelle Tool and Cutter Grinder
The Bonelle Tool and Cutter Grinder The grinder was constructed about 1987 and exhibited at the 89th Model Engineering exhibition where it was awarded a bronze medal (see ME Vol164 No 3868 page 273). Subsequently
More informationLathe Milling Attachment
Lathe Milling Attachment By L C. MASON BY CLEVERLY stacking cold-rolled flat stock together, T-slots and slide for this lathe milling attachment are made without costly machinery. In fact, only two tools,
More informationDriven Toolholders for SAUTER Turrets
Driven Toolholders for SAUTER Turrets Manufacturer of Precision Tools since 1974 INNOVATION PRECISION INDIVIDUALITY QUALITY SERVICE Table of Contents Type Page Driven Toolholders DIN 5482 - Disc-type Turrets
More informationLinear modules Lifting units Rotary modules Grip modules Inductive proximity switches Plug connectors
20000 Linear modules Lifting units Rotary modules Grip modules Inductive proximity switches Plug connectors 23000 22000 21000 20000 09000 08000 07000 06000 05000 04000 03000 02000 01000 823 Notes 824 Technical
More informationSERVICE PARTS LIST PAGE 1 OF 6 BASE ASSEMBLY SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 12" DUAL BEVEL COMPOUND MITER SAW B27A
PAGE 1 OF 6 BASE ASSEMBLY 00 0 EXAMPLE: Component Parts (Small #) Are Included When Ordering The Assembly (Large #). SPECIFY CATALOG NO. AND NO. WHEN ORDERING PARTS 1 02-80-0050 Thrust Bearing (1) 2 05-80-0510
More informationDMS 680. Universal length measuring system gauge inspection for»iso 9000«requirements
DMS 680 Universal length measuring system gauge inspection for»iso 9000«requirements Universal length measuring system DMS 680 Wide range of applications For periodic inspection of gauges, reference gauges,
More informationFAG Hydraulic nuts. Technical Product Information
FAG Hydraulic nuts Technical Product Information Contents Application 2 Design 2 Design variants 3 Pressure generators, connectors 4 Dimension tables for FAG hydraulic nuts (metric) 6 Dimension tables
More information3000, 4000, 4100, 7500, 7700
3000, 4000, 4100, 7500, 7700 Drum & Disc Brake Lathes s Identification READ these instructions before placing unit in service. KEEP these and other materials delivered with the unit in a binder near the
More informationMaraMeter. Indicating Snap Gages
- 9-2 MaraMeter. Indicating Snap Gages Overview MaraMeter. The Indicating Snap Gage is ideal for highly accurate and reliable results on cylindrical work pieces with a narrow tolerance. MaraMeter 840 F
More informationMULTI PURPOSE MACHINE OPERATION MANUAL CHIZHOU HOUSEHOLD MACHINE-TOOL WORKS THE PEOPLE S REPUBLIC OF CHINA
HQ400 HQ400/1 MULTI PURPOSE MACHINE OPERATION MANUAL CHIZHOU HOUSEHOLD MACHINE-TOOL WORKS THE PEOPLE S REPUBLIC OF CHINA CONTENTS 1 OUTSIDE DRAWING 3 2 TECHNICAL SPECIFICATIONS 3 3 APPLICATION 4 4 CONSTRUCTION
More informationANSI APPROVED 04/11/2014 ANSI APPROVED 08/17/2011. 45 Reaffirmation ANSI APPROVED 02/28/2014. 45 Reaffirmation ANSI APPROVED 05/06/2013
STANDARDS STATUS REPORT As of November 4, 2015 Note: Dates in RED indicate the last action taken; Highlighted Items Indicate New/Open Items; Grey items have been closed Document TC Status Comments ASME
More informationTool Holder Catalog TRAUB TNX 65/42 VDI 30 HSK 40 142856-21.02.2014. 0214/Rö
Tool Holder Catalog TRAUB TNX 65/42 VDI 30 HSK 40 142856-21.02.2014 0214/Rö Disclaimer The illustrations in this documents may deviate from the delivered product. We reserve the right to make changes due
More informationStatic and Driven Tools LB and LT Series
Static and Driven Tools LB and LT Series EWS Overview EWS Tool Technologies headquartered in Uhingen (Göppingen district) and with subsidiaries in the USA, South Korea and France belongs to the world wide
More informationUNITED STATES CUTTING TOOL INSTITUTE Product Groupings for Standards Activities CUTTING TOOL PRODUCTS
CUTTING TOOL PRODUCTS 1. BORING ISO 5609 Boring bars for indexable inserts Dimensions ISO 6261 Boring bars (tool holders with cylindrical shank) for indexable inserts Designation JIS B 4128 Boring bars
More informationAXIS DESIGNATION IN NC PART PROGRAMMING
AXIS DESIGNATION IN NC PART PROGRAMMING 1 FUNCTIONS PERFORMED BY THE CONTROL SYSTEM OF NC MACHINE TOOL DISPLACEMENT OF SLIDE MEMBERS. ANGULAR ROTATION OF THE CIRCULAR TABLE. STOP / START MAIN SPINDLE.
More informationAbout Us HAAS Tooling for CNC Turning Centers
About Us WHO IS EPPINGER? Eppinger CNC tool holders to DIN 69880 are manufactured to precision levels far in excess of the required standards using advanced, patented produciton systems and facilities.
More informationOverview. Milling Machine Fundamentals. Safety. Shop Etiquette. Vehicle Projects Machine Shop
Overview Milling Machine Fundamentals Wayne Staats, UW-Madison FSAE Safety Shop Etiquette Before Machining Indicating Calculating Feeds and Speeds Machining Maintenance Safety Respect the machines Common
More informationAlfra Rotabest 100 Metal Core Drilling Machine. Operation Manual
Alfra Rotabest 100 Metal Core Drilling Machine Operation Manual 06/2005 1. Technical Data Prod. No.: 18630 Name : Rotabest 100 Input: Load rpm: 1800 Watt 110/175/245/385 rpm Tool Holder : MT 3 Coolant
More informationMETAL-TURNING LATHE Built from Stock Parts
by Frank Beatty USING STANDARD PARTS and stock materials that are available almost anywhere, you can build this metalworking lathe with only a few tools. Because of simplification of the assembly in order
More informationTool Holder Catalog INDEX ABC VDI 25 LL3602.30051-10.04.2014. 0414/Rö
Tool Holder Catalog INDEX ABC VDI 25 LL3602.30051-10.04.2014 0414/Rö Disclaimer The illustrations in this documents may deviate from the delivered product. We reserve the right to make changes due to errors
More informationRenishaw 2008. apply innovation TM. Calibrating 5-axis machines to improve part accuracy. 5Align
Calibrating 5-axis machines to improve part accuracy 5Align Productive Process Pyramid TM Understanding and tracking machine behaviour Process verification Thermal compensation In-cycle process control
More informationThickness Gauges. convex R 15 or R 40, flat 10 mm Ø, spherical
Thickness Gauges Technical Data for Metric Thickness Gauges Page Model Lifting Contact points Contact points mm mm mm device standard available on request 130 K 15 0.1 10 15 no 6.35 mm Ø flat Ø flat, 130
More informationKey data. The practical machines for your specific grinding solution. A member of the United Grinding Group. The Art of Grinding.
The Art of Grinding. A member of the United Grinding Group CT450 / CT550 The practical machines for your specific grinding solution. Key data The CT450 / CT550 are very flexible internal cylindrical grinding
More informationLarsLap model C for cutting, milling grinding and lapping seats and flanges on globe, safety and control valves
LarsLap model C for cutting, milling grinding and lapping seats and flanges on globe, safety and control valves As a rule, control and reduction valves of the globe type have an integrated plug that narrowly
More informationRebuild Instructions for 70001 and 70010 Transmission
Rebuild Instructions for 70001 and 70010 Transmission Brinn, Incorporated 1615 Tech Drive Bay City, MI 48706 Telephone 989.686.8920 Fax 989.686.6520 www.brinninc.com Notice Read all instructions before
More information14. Mechanisation. and Welding Fixture
14. Mechanisation and Welding Fixture 14. Mechanisation and Welding Fixtures 197 As the production costs of the metal-working industry are nowadays mainly determined by the costs of labour, many factories
More informationMilling and Machining Center Basics
Training Objectives After watching the video and reviewing this printed material, the viewer will gain knowledge and understanding of basic milling theories and procedures. In addition, the viewer will
More informationPrecision Vise Combinations
Precision Vise Combinations PanaVise vises and work holding tools have hundreds of uses limited only by your imagination! Each vise allows the head to Tilt, Turn & Rotate and position your work anywhere
More informationTL-Series Sub-Spindle Operator s Addendum
3 4 5 11 9 TL-Series Sub-Spindle Operator s Addendum 2 1 12 10 6 7 8 20HP VECTOR DUAL DRIVE LIVE TOOLING SUB SPINDLE 2008 Haas Automation, Inc. 96-0037 rev L 9/08 1 1. Introduction Specific M codes are
More information6.6 GEAR MANUFACTURING. Introduction. Gear forming
Valery Marinov, Manufacturing Technology Gear Manufacturing 123 6.6 GEAR MANUFACTURING Introduction Because of their capability for transmitting motion and power, gears are among the most important of
More informationHome"" """"> ar.cn.de.en.es.fr.id.it.ph.po.ru.sw
Home"" """"> ar.cn.de.en.es.fr.id.it.ph.po.ru.sw Milling of Grooves, Elongated Slots and Break-throughs - Course: Techniques for machining of material. Trainees' handbook of lessons (Institut fr Berufliche
More informationMilling machine A milling machine is a machine tool used for the complex shaping of metal and other solid materials. Its basic form is that of a
Milling machine A milling machine is a machine tool used for the complex shaping of metal and other solid materials. Its basic form is that of a rotating cutter or endmill which rotates about the spindle
More informationGM 300 CHECK- AND MEASURING INSTRUMENTS FOR OPTIMAL TOOL CLAMPING
GM 300 CHECK- AND MEASURING INSTRUMENTS FOR OPTIMAL TOOL CLAMPING AND lubrication Check- and Measuring instruments for optimal tool clamping and lubrication Pre-requisite for perfect machining results
More informationSHOP NOTES METAL SHAPER FOR YOUR SHOP
SHOP NOTES METAL SHAPER FOR YOUR SHOP A METAL SHAPER is indispensable for certain machining operations where flat surfaces must be produced within very close limits, such as machining flats on castings,
More informationThe "DAVID" Steam Engine By Alan Marconett Hobbit Engineering HTTP://WWW.HobbitEngineering.com Alan@HobbitEngineering.
The "DAVID" Steam Engine By Alan Marconett Hobbit Engineering HTTP://WWW.HobbitEngineering.com Alan@HobbitEngineering.com (c) 2/20/03 The David steam engine is a simple oscillating steam engine, many plans
More informationACCESSORIES FOR TURNING
ACCESSORIES FOR TURNING Accessories for turning D140 D180 D210 D240 D250 D280 D320 D330 D360 D420 D460 D560 Plane clamping disk Ø 170 mm 344 0295 Plane clamping disk Ø 200 mm 344 0352 Plane clamping disk
More informationTHE ORIGINAL UNI-LOC PIN INSTALLATION PROCEDURE 321D REV03 5/19/08
THE ORIGINAL UNI-LO PIN INSTALLATION PROEDURE 321D 03 5/19/08 1 UNI-LO Pins are best installed during the latter stage of finishing the butt. It is suggested to maintain less than.002 run-out in the front
More informationEasy Machining Center Setup
White Paper Document No. MWA-072-EN_01_1404 April 2014 Easy Machining Center Setup Using FANUC s Direct Input of Workpiece Origin Setting Measured and Tool Length Measurement features to easily establish
More informationTechnical Data. 7. Bearing Fits. 7.1 Interference. 7.2 Calculation of interference F B LLLLLLLLL( A-54
Technical Data 7. Bearing Fits 7.1 Interference For rolling s the rings are fixed on the or in the housing so that slip or movement does not occur between the mated surface during operation or under. This
More informationDismantling and Reassembly Guide
C3 Mini-Lathe Dismantling and Reassembly Guide A picture story book to help you dismantle and reassemble your Sieg C3 Mini-Lathe Arc Euro Trade Ltd. 10 Archdale Street, Syston, Leicester, LE7 1NA. Web:
More informationProviding Answers For All Your Machine Tool Needs
Providing Answers For All Your Machine Tool Needs STANDARD FEATURES FANUC MXP-200FA CONTROL Spindle Features Body Structure POWERFUL 20 HP H / L SHIFTING SPINDLE MOTOR HARDENED & GROUND BOXWAY CONSTRUCTION
More informationL I V E T O O L F O R O K U M A
L I V E T O O L F O R O K U M A The Way to Success [Heimatec headquarters-germany] Heimatec is an international manufacturing company headquartered in Renchen, Germany. Heimatec s 40,000 square foot facility,
More informationMaking Soft Jaws for a Bison 3 Jaw Lathe Chuck
Making Soft Jaws for a Bison 3 Jaw Lathe Chuck By R. G. Sparber Copyleft protects this document. 1 My Bison lathe chuck has served me well for many years. One of its features is the ability to remove the
More informationOriginal Assembly Guide
TCT Multipurpose Single Bevel Sliding Compound Mitre Saw Original Assembly Guide Read instructions before assembling this tool. Table of Contents GB Assembly Guide Read instructions before assembling this
More informationCommon Mechanical Engineering Terms
Common Mechanical Engineering Terms Ball and Detent (n) A simple mechanical arrangement used to hold a moving part in a temporarily fixed position relative to another part. The ball slides within a bored
More informationMilling Milling milling cutter milling machines 1
Milling Milling is a basic machining process by which a surface is generated progressively by the removal of chips from a workpiece as it is fed to a rotating cutter in a direction perpendicular to the
More informationSmartCut EVS Series CNC Mills Combination of CNC technology and manual capability SC EVS-350B CNC SC EVS-550B CNC
Summit Machine Tool Manufacturing L.L.C. SmartCut EVS Series CNC Mills Combination of CNC technology and manual capability SC EVS-350B CNC SC EVS-550B CNC Summit Machine Tool Manufacturing L.L.C. SmartCut
More informationDUGARD. Machine Tools Since 1939. Dugard ECO Series Driven Tool, Slant Bed CNC Lathes. www.dugard.com
DUGARD Machine Tools Since 1939 ECO Series Driven Tool, Slant Bed CNC Lathes www.dugard.com ECO Series - CNC Lathes Amazing speed, power, precision and durability all at an affordable price Rigid and Trustworthy
More informationProgram overview Group 2
Program overview Group 2 2.1 Design principle System 2.1.0-2.1.3 2.2 Drilling and insertion machines Blue Max mini i Range summary 2.2.1 2.3 Assembly aids, drilling jigs and hole-marking templates i Range
More informationCOMPACT. Drilling COMPACT
COMPACT Our latest machine development still produced here in our own factory. This machine combines all our previous experience and knowledge in building drilling machines but at a reduced cost base.
More informationPhone (800) 821-8010 Fax (330) 920-0972 e-mail sales@pdq-marlin.com
1 Table of ontents asic Information dvantages of Quick hange Tooling...2 dvantages of PDQ Quick hange...3 PDQ Shank & Series information...5 Master Holders Morse Taper Holders...6 Milling Machine Holders...7
More informationSPECIAL FEATURES. Air- Electric Clutch Control. Extended Beds and Rams
, SPECIAL FEATURES Extended Beds and Rams Beds and rams can be extended at both ends or at one end only for closing or "homing" operations. Extensions at both ends of the machine provide greatly increased
More informationBuilding an Off-Center Fixture for Turning Pendants
Building an Off-Center Fixture for Turning Pendants Turning a pendant off-center with most available metal pendant chucks means that you will have a significant amount of mass off center, which will limit
More informationDUGARD. Machine Tools Since 1939. Dugard 400 Slant Bed High Precision CNC Lathe. www.dugard.com
DUGARD Machine Tools Since 1939 Dugard 400 Slant Bed High Precision CNC Lathe www.dugard.com Superb Performance, Maximum Stability, Maximum Reliability Precision, Power and Capacity Make the Dugard 400
More informationNOT SEARCHING, BUT FINDING
NOT SEARCHING, BUT FINDING We carefully ensure that our wide and extensive range provides a good assortment so that you feel in good hands, even if you are looking for portable measurement devices to provide
More informationCNC HARDWARE & TOOLING BASICS
Computer Aided Manufacturing (CAM) CNC HARDWARE & TOOLING BASICS Assoc. Prof. Dr. Tamer S. Mahmoud 1. Parts of CNC Machine Tools Any CNC machine tool essentially consists of the following parts: Part Program,
More informationMandrel system MIS. www.microcentric.de
Mandrel system MIS MicroCentric GmbH Berblingerstr. 16 71254 itzingen / Germany Tel.: +49 (0) 7156 17819-0 Fax: +49 (0) 7156 17819-20 E-Mail: info@microcentric.de www.microcentric.de Products in this catalog:
More informationFACTORY INSTALLED OPTIONS:
Myford MG 12 M MG 12 ME Manually operated cylindrical grinding machine - capacity 5in x 12in - providing hand operated table traverse, hand operated wheelhead travel, table swivels 7 degrees either way,
More informationHYDRO-FIX hydraulic clamping system. For boring bars and driven tools
HYDRO-FIX hydraulic clamping system For boring bars and driven tools Improve your productivity HYDRO-FIX hydraulic clamping system has successfully been used for over 15 years. HYDRO-FIX is excellent for
More informationDismantling and Reassembly Guide
Super X3 Mill Dismantling and Reassembly Guide A picture story book to help you dismantle and reassemble your Sieg Super X3 Mill Arc Euro Trade Ltd. 10 Archdale Street, Syston, Leicester, LE7 1NA. Web:
More informationSC-32 CNC LATHE OPERATION MANUAL
SC-32 OPERATION MANUAL NCT Ipari Elektronikai Kft. 1 / 29 Dátum: 2013.09.27. CONTENTS 1. ACCURACY RECORD... 2 2. SAFETY PRECAUTIONS... 2 2.1. Safety Rules... 2 2.2. Warning label attaching positions...
More informationMachine Tool Control. Besides these TNCs, HEIDENHAIN also supplies controls for other areas of application, such as lathes.
Machine Tool Control Contouring controls for milling, drilling, boring machines and machining centers TNC contouring controls from HEIDENHAIN for milling, drilling, boring machines and machining centers
More informationMilling & Machining Centers
Training Objective After watching the program and reviewing this printed material, the viewer will gain knowledge and understanding of basic milling theories and procedures. In addition, the viewer will
More informationRETROFITTING THE X3 MILLING MACHINE (2)
RETROFITTING THE X3 MILLING MACHINE (2) Dick Stephen continues with the mechanical modifications. Fitting the ball screws The 12mm 2mm pitch supplied by THK ball screws are delivered with the nut fitted
More informationCOLLEGE OF ENGINEERING AND APPLIED SCIENCE MACHINE SHOP TOOLS AND PRACTICES
COLLEGE OF ENGINEERING AND APPLIED SCIENCE MACHINE SHOP TOOLS AND PRACTICES I. OBJECTIVE To provide an overview and basic knowledge of the University of Wyoming, College of Engineering, equipment, tools,
More informationPrecise heavy-duty cutting
PR 130 / PR 150 / PR 160 / PR 180 / PR 200 / PR 260 Precise heavy-duty cutting P-SERIES K-SERIES T-SERIES MILLFORCE 02 / Fields of application 03 / Machine concept 04 / Machine technology 05 / Options
More informationCORE COMPETENCY REQUIREMENTS NIMS CERTIFIED CNC SET UP PROGRAMMER MILLING AND TURNING
CORE COMPETENCY REQUIREMENTS NIMS CERTIFIED CNC SET UP PROGRAMMER MILLING AND TURNING APPRENTICE CORE COMPETENCIES 1. Identify and Demonstrate Usage of Machine Safety and Personal Protective Equipment
More informationSECTION G2: CABLE PROCESSOR MODULE MAINTENANCE
SECTION G2: CABLE PROCESSOR MODULE MAINTENANCE Cable Processor Module overview WARNING! When tipping the Cable Processor Module back, (after removing the toggle arm pin), use extreme caution not to drop
More informationSUBCOURSE EDITION OD1645 8 LATHE OPERATIONS
SUBCOURSE EDITION OD1645 8 LATHE OPERATIONS US ARMY REPAIR SHOP TECHNICIAN WARRANT OFFICER ADVANCED CORRESPONDENCE COURSE MOS/SKILL LEVEL: 441A LATHE OPERATIONS SUBCOURSE NO. OD1645 EDITION 8 US Army
More information[ means: Save time, money and space! MAXXMILL 500. Vertical milling center for 5-side machining
[ E[M]CONOMY] means: Save time, money and space! MAXXMILL 500 Vertical milling center for 5-side machining MAXXMILL 500 MAXXMILL 500 is the ideal vertical milling center for the for the 5-axis operation
More informationzeus Marking Technology
zeus Marking Technology Marking Tools Marking Rolls Engraving Technology Die Premium-Marke von Hommel+Keller zeus MARKING TECHNOLOGY zeus is a premium brand that stands for highest quality, precision,
More informationS40. The Allrounder for complex grinding jobs.
S40 The Allrounder for complex grinding jobs. Advantages S40 Dimensions Distance between centres 1000/1600 mm (39.4 /63 ) Height of centres 175/225 mm (6.9 /8.9 ) Maximum workpiece weight 130/150 kg (286/330
More informationfor MANUAL MILLING MACHINES
UC RIVERSIDE MECHANICAL ENGINEERING DEPARTMENT MACHINE SHOP STANDARD OPERATING PROCEDURES for MANUAL MILLING MACHINES REVISION: V5 DATE: 11-15-2011 TABLE OF CONTENTS SECTION TOPIC(S) PAGE Basic Capabilities
More information413 NOVA SYSTEM PAN AMERICAN TOOL CORPORATION 5990 NW 33309-2208 PHONE (954)735-8665 TOLL FREE 1-800-423-2764 FAX
413 NOVA SYSTEM 5990 NW 31st Avenue Ft. Lauderdale, Florida 33309-2208 PHONE (954)735-8665 TOLL FREE 1-800-423-2764 FAX (954)735-8668 2013 Pan American Tool Corporation 2013 TERMS AND CONDITIONS TERMS:
More informationSection A. GENERAL INFORMATION
Section A. GENERAL INFORMATION I. Description The information and instructions for attaching the sidecar to the right-hand side of the motorcycle are contained in this handbook and must be carefully observed.
More informationEVEN FOR SMALL QUANTITIES WE GET STARTED RIGHT AWAY...
EVEN FOR SMALL QUANTITIES WE GET STARTED RIGHT AWAY... Because we produce in-house, so we don t have far to go. Our decisions are not based on when and who can do what in Asia; instead, we look at what
More informationV-Series. 4-Way Precision Lathe with Automated Cycles. www.weiler.de. Precision in Every Dimension. New product: the first 4-way precision
Precision in Every Dimension Service New product: the first 4-way precision lathe with automated cycles V-Series 4-Way Precision Lathe with Automated Cycles www.weiler.de Manual/Engine Lathes Cycle-Controlled
More informationKOMET. Adaptors Perfecting the Connection. With our comprehension programme of tool adaptors we have the right answer for every requirement.
KOMET Adaptors Perfecting the Connection With our comprehension programme of tool s we have the right answer for every requirement. Adaptors with connections specified by manufacturers available on request.
More informationTypes of 3D Scanners and 3D Scanning Technologies.
Types of 3D Scanners and 3D Scanning Technologies. There are many types of 3D scanners and 3D scanning technologies. Some are ideal for short range scanning while others are better suited for mid or long
More informationFlash Butt Welding Machines
Flash Butt Welding Machines Types AS 15 - AS 320 Flash butt welding current brake current (ka) current time flattening reversal preheating welding time flash butting forging A reliable and economic process
More informationSetting up the DeskCNC controller.
1) Determine the steps to linear motion ratios for each axis. 2 2) Determine Maximum velocity (speed). 3 3) Setting up the software Machine Tab 4 4) Setting up the software DeskCNC Setup Tab 5 5) Setting
More information1722 / 1723 / 1724 DIGI-MET Indicators
1722 / 172 / 1724 DIGI-MET Indicators for static measurements IP 52 1722 502 172 502 1724 502 Electronic functions Housing Ø 60 mm Replacement probe tip M 2.5 Protection class IP52 Clamping shank Ø 8 mm
More informationABERLINK 3D MKIII MEASUREMENT SOFTWARE
ABERLINK 3D MKIII MEASUREMENT SOFTWARE PART 1 (MANUAL VERSION) COURSE TRAINING NOTES ABERLINK LTD. EASTCOMBE GLOS. GL6 7DY UK INDEX 1.0 Introduction to CMM measurement...4 2.0 Preparation and general hints
More informationDIGI-MET ELECTRONIC INDICATORS
DIGI-MET ELECTRONIC INDICATORS Featuring Direct RS232C Output And Swiss SYLVAC Electronics. A sophisticated non-contact linear measuring system... can be connected to any computer or printer with no interface
More informationOPERATING INSTRUCTIONS FOR
OPERATING INSTRUCTIONS FOR MEDECO KEY MACHINES FOR MEDECO ORIGINAL, BIAXIAL, MEDECO 3, KEYMARK CLASSIC & KEYMARK X4 PRODUCTS MEDECO HIGH SECURITY LOCKS ASSUMES NO RESPONSIBILITY FOR INJURY OR PROPERTY
More informationDUGARD. Machine Tools Since 1939. Dugard 200HT / 200MC Slant Bed, High Precision CNC Lathes. www.dugard.com
DUGARD Machine Tools Since 1939 Dugard 00HT / 00MC Slant Bed, High Precision CNC Lathes www.dugard.com Dugard 00HT / 00MC Hydraulic Tailstock Quill can be controlled by programme or manually, auto sensing
More informationThe Speed of Live and the Accuracy of Fixed
The Speed of Live and the Accuracy of Fixed SG10A CYLINDER HEAD SEAT & GUIDE MACHINE Light Weight Work Head The SG10A has a light weight work head for fast and accurate centering for the minimum concentricity.
More informationAdvantages and application of PCD and CBn tools
PCD and CBN tools Advantages and application of PCD and CBn tools Powerful and economical Tools with PCD and CBN cutting edges are the ideal solution for difficult-to machine, highly abrasive materials.
More information2010 APPLICATION REFERENCE GUIDE
2010 APPLICATION REFERENCE GUIDE INDEX QUALITY POLICY 2 ERGO ASSIST STANDARD 4-13 CUSTOM 14-18 END EFFECTORS 19-24 LIFT ASSIST 25-41 FIXTURED TOOLS 42-53 FIXTURES 54-63 ASSEMBLY TABLES 64-72 CARTS/ DUNNAGE
More informationUltra Live Center RN. Clamping tools for clamping on machine tools. NEIDLEIN revolving ultra live centers type RN ensure: Type RN with morse taper
Ultra Live Center RN Type RN with morse taper NEIDLEIN ultra live centers are designed for employment in turning, grinding and other production machines. Owing to the application of bearing and the stable
More informationAtling proudly presents the next generation self centering steady rests ATLING. Ockelbo Sweden. AX Steady Rests
Atling proudly presents the next generation self centering steady rests ATLING Ockelbo Sweden AX Steady Rests 1 The New AX Steady Rest The Atling AX series is the result of several years of development
More informationManufacturing Processes II Prof. A. B Chattopadhyay Department of Mechanical Engineering Indian Institute of Technology, Kharagpur
Manufacturing Processes II Prof. A. B Chattopadhyay Department of Mechanical Engineering Indian Institute of Technology, Kharagpur Lecture No.23A Construction, Operation and Tool Layout of Semiautomatic
More informationMarStand. Indicator Stands Comparator Stands
MarStand. Indicator Stands Comparator Stands Indicator Stand 815 GN 6 2 Indicator Stand 2400 6 2 Indicator Stand 815 MA 6 3 Indicator Stand 815 MB 6 3 Indicator Stand 815 MG 6 4 Indicator Stand 815 P 6
More informationMilling Chuck Features
Milling Chuck Features Since its first introduction into the industry in 1963, Nikken has sold over 2,000,000 worldwide and never stopped improving its original design. Featuring multi-roller bearings
More information