METROLOGIC INSTRUMENTS, INC. USB Addendum for the IS4220 Programming Guide (MLPN x)

Transcription

1 METROLOGIC INSTRUMENTS, INC. USB Addendum for the IS4220 Programming Guide (MLPN x)

2

3 LOCATIONS CORPORATE HEADQUARTERS NORTH AMERICA EUROPEAN, MIDDLE EAST & AFRICAN HEADQUARTERS USA, NEW JERSEY GERMANY, MUNICH Metrologic Instruments, Inc. Metrologic Instruments GmbH Tel: ID-METRO Fax: Tel: Fax: SOUTH AMERICA, BRAZIL SÃO PAULO GERMANY, MUNICH Metrologic do Brasil Ltda. Metrologic Instruments GmbH Tel: Fax: Tel: Fax: SOUTH AMERICA, OUTSIDE BRAZIL SÃO PAULO ITALY, BOLOGNA Metrologic South America Metrologic Instruments Italia srl Tel: Fax: Tel: Fax: info@sa.metrologic.com info@it.metrologic.com ASIA, SINGAPORE FRANCE, PARIS Metrologic Asia (Pte) Ltd Metrologic Eria France SA Tel: Fax: Tel: +33 (0) info@sg.metrologic.com Fax: +33 (0) info@fr.metrologic.com CHINA, SUZHOU Metro Technologies Co., Ltd. SPAIN, MADRID Tel: Fax: Metrologic Eria Ibérica, SL info@cn.metrologic.com Tel: Fax: info@es.metrologic.com Metro Sales Office Tel: Fax: Metrologic Europe Repair Center (MERC) info@cn.metrologic.com Metrologic Eria Ibérica, SL Tel: Fax: JAPAN, TOKYO Metrologic Japan Co., Ltd. UNITED KINGDOM, BASINGSTOKE Tel: Fax: Metrologic Instruments UK Limited info@jp.metrologic.com Tel: +44 (0) Fax: +44 (0) info@uk.metrologic.com RUSSIA, MOSCOW Metrologic Russia Tel: Fax: info@ru.metrologic.com Copyright 2004 by Metrologic Instruments, Inc. All rights reserved. No part of this work may be reproduced, transmitted, or stored in any form or by any means without prior written consent, except by reviewer, who may quote brief passages in a review, or provided for in the Copyright Act of Products and brand names mentioned in this document are trademarks of their respective companies. ii

4 TABLE OF CONTENTS Introduction... 1 What is the difference between USB Keyboard (IS ) and USB Point-of-Sale (IS )?... 1 USB Keyboard Emulation with the IS USB Point-of-Sale (POS) with the IS Configuration for USB Keyboard Emulation (IS )... 3 Configuration for USB Point-of-Sale (IS )... 6 Test Bar Code... 7 iii

5 INTRODUCTION Metrologic s IS4220 Series has two USB models. The first is the IS , which converts serial RS232 formatted data to USB Keyboard. The second is the IS , which converts serial RS232 formatted data to Point-of Sale (POS) communication protocol. Both models leave the factory pre-configured to their respective interfaces. This guide contains the configuration bar codes necessary to ensure that the scanner communicates properly with the host if for some reason the factory default configuration is lost or needs to be modified. What is the difference between USB Keyboard (IS ) and USB Point-of-Sale (IS )? When scanning with the IS , data will appear in the current application that is active on your PC. The data is entered just as if the keys were pressed on the keyboard. When scanning with the IS the data emulates serial (RS232) data through the use of a Metrologic developed driver. The device will then work with existing serial (RS232) applications. The drivers can be downloaded at: For Windows 2000/XP Operating Systems ftp://ftp.metrologic.com/pub/download/software/mtlgpos.zip For Windows 98 (Second Edition) Operating System ftp://ftp.metrologic.com/pub/download/software/mtlgpos98.zip 1

6 INTRODUCTION USB Keyboard with the IS The IS leaves the factory pre-configured for USB Keyboard. This guide contains the configuration bar codes necessary to ensure that the scanner communicates properly with the host if for some reason the factory configuration is lost or needs to be modified (see page 3). The scanner communicates using RS232 protocol. The default (RS232) settings of the scanner are as follows: 9600 baud 2 stop bits 7 data bits space parity In addition, the scanner uses ACK/NAK and XON/XOFF software handshaking, plus the data transmission ends with both carriage return and line feed suffixes. The 1 st and 2 nd prefixes are used to set the country of the keyboard. Example #1: IS4220, German Keyboard, Bar Code = , No custom prefixes available. Configuration: <Ctl-V> <D> <012345> <CR><LF> Pref #1 Pref #2 Data Terminators Data Transmitted = <CR> Prefixes #1 and #2 specify the German keyboard and the <CR> <LF> terminators are needed by the IS for framing the data. Only 2 custom prefixes are available on the IS4220. USB Point-of-Sale (POS) with the IS The IS leaves the factory pre-configured for USB Point-of-Sale. This guide contains the configuration bar codes necessary to ensure that the scanner communicates properly with the host if for some reason the factory configuration is lost or needs to be modified (see page 6). The scanner communicates using RS232 protocol. The default (RS232) settings of the scanner are as follows: 9600 baud, 2 stop bits 7 data bits, space parity In addition, the scanner uses ACK/NAK and XON/XOFF software handshaking, and the data transmission ends with both carriage return and line feed suffixes. When using USB Point-of-Sale, special prefixes are not required.

7 CONFIGURATION FOR USB KEYBOARD EMULATION (IS ) The IS leaves the factory pre-configured for USB Keyboard. If for some reason the factory configuration is lost or needs to be modified the IS must be reconfigured using the following bar codes before the scanner can communicate properly with the host system. Configuration for USB Emulation must be completed before enabling/disabling any additional features documented in the programming guide provided with the scanner. Important: When enabling/disabling additional features do not scan the recall defaults bar code or all of the existing USB Emulation configurations will be lost and the scanner will need to be reconfigured. Scan the following bar codes in numbered sequence ENTER/EXIT RECALL DEFAULTS * * D F 1 3. *ENABLE RS232 INTERFACE 4. ENABLE XON/XOFF L P 2 S H 4 5. ENABLE ACK/NAK 6. 1 ST PROGRAMMABLE PREFIX ID S H 2 R A T 7. Refer to the Prefix #1 column in the USB Keyboard Country Cross - Reference Table on Page 4. Scan the 3 Code Bytes associated with the required Country Keyboard. Example To set for Prefix #1 for Belgium: 1. Locate Belgium in the Country column of the table on page Check the Prefix #1 column next to Belgium to identify the required codes (022). 3. Go to Page 5 and scan code byte RB0, RB2, then RB2 again. 3

8 CONFIGURATION FOR USB KEYBOARD EMULATION (IS ) 8. 2 ND PROGRAMMABLE PREFIX ID R A U 9. Refer to the Prefix #2 Column of the table below. Scan the 3 Code Bytes associated with the required country keyboard. Example To set Prefix #2 for Belgium: 1. Locate Belgium in the Country column of the table below. 2. Check the Prefix #2 column next to the Belgium to identify the required codes (065). 3. Go to Page 5 and scan code byte RB0, RB6, and RB5. USB KEYBOARD COUNTRY CROSS - REFERENCE TABLE COUNTRY PREFIX #1 PREFIX #2 (decimal) (decimal) DESCRIPTION OF PREFIXES Belgium <CTRL V> A U.K <CTRL V> B French <CTRL V> C German <CTRL V> D Italian <CTRL V> E Spain <CTRL V> F U.S <CTRL V> G Reserved <CTRL V> H Swiss <CTRL V> I Swedish/Finnish <CTRL V> J Japanese <CTRL V> K Reserved <CTRL V> L Continued on next page. 4

9 CONFIGURATION FOR USB KEYBOARD EMULATION (IS ) Scan the 3 code bytes associated with the required country keyboard. RB0-0 RB1-1 R B 0 R B 1 RB2-2 RB3-3 R B 2 R B 3 RB4-4 RB5-5 R B 4 R B 5 RB6-6 RB7-7 R B 6 R B 7 RB8 RB9-9 R B 8 R B ENTER/EXIT * * 5

10 CONFIGURATION FOR USB POS EMULATION (IS ) The IS leaves the factory pre-configured for USB Point-of-Sale (POS). If for some reason the factory configuration is lost or needs to be modified the IS must be reconfigured using the following bar codes before the scanner can communicate properly with the host system. Configuration for USB Emulation must be completed before enabling/disabling any additional features documented in the programming guide provided with the scanner. Important: When enabling/disabling additional features do not scan the recall defaults bar code or all of the existing USB Emulation configurations will be lost and the scanner will need to be reconfigured. Scan the following bar codes in numbered sequence. 1. ENTER/EXIT 2. RECALL DEFAULTS * * D F 1 3. ENABLE RS232 INTERFACE 4. ENABLE XON/XOFF L P 2 S H 4 5. ENABLE ACK/NAK 6. ENTER/EXIT S H 2 * * 6

11 TEST BAR CODE Scanning the following bar code will transmit the encoded characters followed by the software number of the communication/power cable. 7

12 July 2004 Printed in the USA