Windows 2008 Server Installation

Transcription

1 PCS Tech Tips Windows Server 2008 Install Windows 64-bit Foundation Server HP Proliant ML310G5p Embedded SATA RAID Controller Copyright 2010 Practical Computer Solutions, Inc. 1

2 2

3 Overview of Installation This document will provide step by step instructions on how to install the Windows 2008 Foundation Server software on an HP Proliant ML310 (G5p) server. The server is using 2 250GB SATA drives in a RAID 1 array using the onboard RAID controller. The server will be configured as if it was going to be used as a File and Print server for hosting our Profits accounting software at a typical small business. Setting up the Hardware The first step after unboxing the server is to configure the system BIOS using the BIOS setup utility. You access the utility by pressing F9 when the system is booting. Once you are in the setup utility perform the following steps: 1) System Serial Ports Disable All Ports LPT Ports Disable All Ports NumLock On NIC s Disable PXE Power Regulator HP Dynamic Power Saving Mode 2) Boot Controller Order 82801GR SATA RAID Controller (Intel) 82801GR SATA Controller #2 3) Server Availability Thermal Shut Down Enabled Wake On Lan Disabled POST F1 Prompt- Disabled Auto Power On Enabled 4) Server Asset Text Custom POST message Contact ) Advanced Options Virual Disk Enabled (Needed to run SmartStart CD) Embedded SATA RAID Enabled 6) StandardBoot Order CDROM HD 3

4 USB (Must be below HD or RAID will not boot correctly) Diskette Save the changes using F10 and reboot the system. When the system begins to reboot watch the screen and press F8 when you see a message about the RAID controller configuration. Once you are in the controller setup screen perform the following steps: 1) Select Array Configuration Utility, then Create Array a) Press INSERT on each of the two displayed drives This will add the drives to the array. b) Press ENTER c) Select RAID 1 Mirror, Press ENTER d) Name the array, i.e Main Mirrored e) Select QuickInit (Build takes hours while it checks the drives) f) Select Done g) Select 00 (First Drive) for the source h) Select YES Your array will be created on the hardware level. Windows will be installed on the array and will have no idea that it is running on a Mirrored system. O/S Installation (2008 Foundation Server 64bit) The current version of the Windows Server DVD and the HP SmartStart disk (v8.40) do not contain the correct RAID Drivers. This prevents us from using the HP SmartStart disk for installing the O/S. So we first need to get the correct driver. The driver we need contains both the 32 and 64bit versions. The 32bit version is needed to access the array during the initial install. The 64bit version is needed to boot to the newly installed O/S. The driver you need is called cp exe. It was located at peid=15351&prodseriesid= &prodnameid= &swenvoid=4024&swlang=8&mode=2& taskid=135&switem=mtx-1f2b48ef26ed4136ba2ccca720 or it can be found on our website at Once you have this driver copy it to a USB thumb drive. You will need this during the installation of the O/S. Insert the thumb drive in the USB port and the Windows O/S disk in the drive. Now turn on the ML310 and boot from the DVD. Once at the Windows installation screen select INSTALL NOW and then Customer Install. Down near the bottom of the screen is an option to Load Driver. Click this link and browse to your thumb drive and select the AARAHCI.INF file. 4

5 You should then be prompted for Where do you want to install Windows. If the driver loaded correctly you should see your RAID Array displayed as a single drive of 232.5GB. Now select Drive Options to create a partition for the O/S. I chose to create one of 75GB for the O/S leaving the rest for a DATA partition. After creating the new partition, select it and then format it as an NTFS partition. If you see an error about Windows could not find a boot Partition, make sure that the BIOS boot order has the USB key BELOW the HD option. Now Continue with the standard installation screens. 5