System pro M compact Miniature Circuit Breaker S 200/S 200 M

Transcription

1 Data Sheet System pro M compact Miniature Circuit Breaker S 200/S 200 M 2CDC021023S0012 2CDC021038S0012 The miniature circuit breakers of the System pro M compact series S 200 and S 200 M provide state-of-the-art safety and comfort. They stand out due to their high performance and the wide range of accessories and approvals. Features Clear contact position indication in red/green ( real CPI ) Unique, patented twin terminal with captive screws and an increased opening for cables up to max. 35 mm 2, finger-proof (IP20) Busbar slot in the back for best visibility during installation High performance at an increased rated voltage for marine and industrial applications: 10 ka/15 ka at U e = 440 V AC acc. to IEC/EN Individual product identification code Approved acc. to IEC/EN , IEC/EN and UL 1077/CSA 22.2 No. 235 for global use

2 Technical data S 200 S 200 M General Data Standards IEC/EN , IEC/EN UL 1077 IEC/EN , IEC/EN UL 1077, CSA 22.2 No. 235 Poles 1P, 2P, 3P, 4P, 1P+N, 3P+N Tripping Characteristics B, C, D, K, Z Rated current 0.5 up to 63 A Rated frequency 50/60 Hz Rated insulation voltage U i 250 V AC (phase to ground), 500 V AC (phase to phase) Overvoltage Category III Pollution Degree 3 IEC/EN Rated operational voltage U n 1P: 230/400 V AC; 1P+N: 230 V AC; 2P, 3P, 4P: 400 V AC; 3P+N: 400 V AC Max. power frequency recovery voltage U max 1P: 253 V AC; 1P+N: 253 V AC; 2P, 3P, 4P: 440 V AC; 3P+N: 440 V AC; 1P: 72 V DC; 2P: 125 V DC Min. operating voltage 12 V AC, 12 V DC Rated short-circuit capacity I cn 6 ka 10 ka Energy limiting class (B, C up to 40 A) 3 Rated impulse withstand voltage U imp (1.2/50 µs) 4 kv (test voltage 6.2 kv at sea level, 5 kv at 2,000 m) Dielectric test voltage 2.0 kv (50/60 Hz, 1 min) Reference temperature for tripping characteristics B, C, D: 30 C Electrical endurance < 32 A: 20,000 ops. (AC), 1,000 ops. (DC); one cycle 2 s - ON, 13 s - OFF 32 A: 10,000 ops. (AC), 1,000 ops. (DC); one cycle 2 s - ON, 28 s - OFF IEC/EN Rated operational voltage U e 1P: 230 V AC; 1P+N: 230 V AC; 2P, 3P, 4P: 440 V AC; 3P+N: 440 V AC Max. power frequency recovery voltage U max 1P: 253 V AC; 1P+N: 253 V AC; 2P, 3P,4P: 462 V AC; 3P+N: 462 V AC; 1P: 72 V DC; 2P: 125 V DC Min. operating voltage 12 V AC, 12 V DC Rated ultimate short-circuit breaking capacity I cu 10 ka 15 ka Rated service short-circuit breaking capacity I cs 7.5 ka 40 A: ka 50, 63 A: 7.5 ka Rated impulse withstand voltage U imp (1.2/50 µs) 4 kv (test voltage 6.2 kv at sea level, 5 kv at 2,000 m) Dielectric test voltage 2.0 kv (50/60 Hz, 1 min) Reference temperature for tripping characteristics B, C, D: 55 C; K, Z: 20 C Electrical endurance < 32 A: 20,000 ops. (AC), 1,000 ops. (DC); one cycle 2 s - ON, 13 s - OFF 32 A: 10,000 ops. (AC), 1,000 ops. (DC); one cycle 2 s - ON, 28 s - OFF UL/CSA Rated voltage 1P: 277 V AC, 60 V DC 2...4P: 480 Y/277 V AC, 110 V DC 1P: 277 V AC, 60 V DC 2...4P: 480 Y/277 V AC, 125 V DC Rated interrupting capacity 6 ka (AC), 10 ka (DC) Application Suppl. prot. for general use. Application Codes: TC2, OL0, SC: U1 Reference temperature for tripping characteristic B, C, D, K, Z: 25 C Electrical endurance 6,000 ops. (AC), 6,000 ops. (DC); one cycle 1 s - ON, 9 s - OFF Mechanical data Housing Insulation group II, RAL 7035 Insulation group I, RAL 7035 Toggle Insulation group II, black, sealable Contact position indication Marking on toggle (I ON/0 OFF), Real CPI (red ON/green OFF) Protection degree acc. to EN IP20 1), IP40 in enclosure with cover Mechanical endurance 20,000 ops. Shock resistance acc. to IEC/EN g, 2 shocks, 13 ms Vibration resistance acc. to IEC/EN g, 20 cycles at Hz with load 0.8 Environmental conditions acc. to IEC/EN cycles with 55 C/90-96 % and 25 C/ % Ambient temperature C Storage temperature C 1) Also fulfilling the requirements acc. to the protection degree IPXXB 2-2CDC002157D0202

3 Technical data and tripping characteristics S 200 S 200 M Installation Terminal Failsafe bi-directional cylinder-lift terminal Cross-section of conductors (top/bottom) solid, stranded: 35 mm 2 / 35 mm 2 flexible: 25 mm 2 / 25 mm AWG 1) Cross-section of busbars (top/bottom) 10 mm 2 / 10 mm AWG 2) Torque 2.8 Nm 18 in-ibs. Screwdriver No. 2 Pozidrive Mounting On DIN rail 35 mm acc. to EN by fast clip Mounting position any Supply optional Dimensions and weight Mounting dimensions acc. to DIN Mounting dimension 1 Pole dimensions (H x D x W) 88 x 69 x 17.5 Pole weight approx. 115 g Combination with auxiliary elements Auxiliary contact Yes Signal/auxiliary contact Yes Shunt trip Yes Undervoltage release Yes Motor Operating Device Yes 1) AWG 18 4 acc. to UL 486A 486B 2) AWG 18 8 acc. to UL 486A 486B Tripping characteristics Acc. to Tripping characteristics Rated current Thermal release 3) Electromagnetic release 4) 1.45 Currents: conventional non-tripping current I 1 conventional tripping current I 2 IEC/EN B 6 to 63 A 1.13 > 1 h Tripping time Range of instantaneous tripping Tripping time s ( 32 A)/ s ( > 32 A) s ( 32 A)/ s ( > 32 A) > 0.2 s > 0.2 s 1.2 < 1 h 5) 5 < 0.1 s s ( 32 A)/ s ( > 32 A) C 0.5 to 63 A 1.13 > 1 h < 1 h 5) 10 < 0.1 s D 0.5 to 63 A 1.13 > 1 h < 1 h 5) 20 < 0.1 s IEC/EN K 0.5 to 63 A 1.05 > 1 h < 1 h 5) 14 < 0.2 s Z 0.5 to 63 A 1.05 > 1 h < 1 h 5) 3 < 0.2 s 3) The thermal releases are calibrated to a nominal reference ambient temperature; for B, C, D the reference value is 30 C, for K and Z the reference value is 20 C. In the case of higher ambient temperatures, the current values fall by approx. 6 % for each 10 K temperature rise. 4) The indicated tripping values of electromagnetic tripping devices apply to a frequency of 50/60 Hz. The thermal release operates independent of frequency. 5) As from operating temperature (after I 1 > 1h) 2CDC002157D0202-3

4 Tripping characteristics B characteristic C characteristic D characteristic Z characteristic 2CDC022010F0211 2CDC022060F0211 2CDC022006F0211 2CDC022008F0211 2CDC022108F0209 K characteristic 4-2CDC002157D0202

5 teristics A A Miniature Circuit Breaker S 200/S 200 M Derating Deviating ambient temperature For installations of miniature circuit breakers at other temperatures than the reference value derating factors have to be considered. The rated value of the current of a miniature circuit breaker refers to a reference ambient temperature of 30 C for circuit breakers with the characteristics B, C and D and 20 C for circuit breakers with the characteristics K and Z. The following table contains the derating of the load capability at ambient temperatures from -40 C to 70 C for the characteristics B, C, D, K and Z. Tripping Rated Maximum operating current at ambient temperature T charac- current - 40 C - 30 C - 20 C - 10 C 0 C 10 C 20 C 30 C 40 C 50 C 60 C 70 C B, C, D K, Z Influence of adjacent devices If several miniature circuit breakers are installed directly side by side with high load on all poles, a correction factor has to be applied to the rated current (see table). If distance pieces are used, the factor is not to be considered. No. of adjacent devices Factor F 1 1 2, , Example Installation of 8 adjacent miniature circuit breakers S201-C16 at 40 C ambient temperature Rated current = 16 A Max. operating current at 40 C = 15,.1 A (see table above) Factor F = 0.75 (see left table) = 15.1 A x 0.75 = A Result: The operating current can only add up to max A 2CDC002157D0202-5

6 Internal resistance and power loss Internal resistance and power loss per pole Rated Tripping characteristic current B, C 1) D K Z Internal resistance Power loss Internal resistance Power loss Internal resistance Power loss Internal resistance Power loss R i P v R i P v R i P v R i P v A mω W mω W mω W mω W ) Current ratings A, 8 A apply to C characteristic only Internal resistances are subject to application-specific and environment-specific conditions and are therefore to be considered as typical values. 6-2CDC002157D0202

7 Let-through energy I 2 t Characteristics B, C - 230/400 V let-through energy 2CDC002157D0202-7

8 Let-through energy I 2 t Characteristics D, K - 230/400 V let-through energy 8-2CDC002157D0202

9 Let-through energy I 2 t Characteristic Z - 230/400 V let-through energy 2CDC002157D0202-9

10 Accessories and dimensional drawing Accessory overview H Auxiliary contact S2C-H6R (change-over contact) H-R Auxiliary contact S2C-H6-...R S/H Signal/Auxiliary contact S2C-S/H6R S/H (H) Signal/Auxiliary contact used as auxiliary contact S2C-S/H6R ST Shunt trip S2C-A... UR Undervoltage release S2C-UA OR Overvoltage release S2C-OVP Dimensional drawing 2CDC022007F0010 2CDC092002F0212 H-L Auxiliary contact S2C-H...L H-BF Auxiliary contact for bottom fitting S2C-H01 (1 per pole) S2C-H10 BP Mechanical tripping device S2C-BP NT Neutral disconnector S2C-Nt MOD-S 1) Motor operating device S2C-CM DDA 200 RCD-block DDA ) In case of using S 200/S 200 M coupled with DDA 200, MOD-S does not operate in case of earth-leakage fault. 10-2CDC002157D0202

11 Approvals Country approvals Approval mark Description Country Ship approvals Approval mark Description Country RCM Australia BV France ÖVE Austria GL Germany CEBEC Belgium RINA Italy CSA Canada (S 200 M only) ABS USA CCC EZU DEMKO FIMKO China Czech Republic Denmark Finland Not all approvals are printed on the MCBs. The indicated approvals generally cover all available approvals worldwide. To verify the approval status in your country please get in touch with your ABB contact person. NF France VDE Germany IMQ Italy SIRIM Malaysia KEMA Netherlands NEMKO Norway BBJ Poland CERTIF Portugal GOST GOST Fire Russia HDB Singapore SIQ Slovenia AENOR Spain SEMKO Sweden S+ Switzerland UL1077 USA 2CDC002157D

12 Contact us ABB STOTZ-KONTAKT GmbH Eppelheimer Straße Heidelberg, Germany Phone: +49 (0) Fax: +49 (0) info.desto@de.abb.com You can find the address of your local sales organization on the ABB home page -> Low Voltage Products and Systems Note: We reserve the right to make technical changes or modify the contents of this document without prior notice. With regard to purchase orders, the agreed particulars shall prevail. ABB AG does not accept any responsibility whatsoever for potential errors or possible lack of information in this document. We reserve all rights in this document and in the subject matter and illustrations contained therein. Any reproduction, disclosure to third parties or utilization of its contents in whole or in parts is forbidden without prior written consent of ABB AG. Copyright 2012 ABB All rights reserved Brochure number 2CDC002157D0202 (08/ ZVD)