ZS25 Screw Clamp Terminal Blocks Feed-through

Transcription

1 Technical Datasheet SNK668D0 Catalogue Page SNK678S0 ZS Screw Clamp Terminal Blocks Feed-through Save space by connecting conductors up to mm² AWG in just mm 0.47 in spacing. SNK68V004 SNK004F0000 D CAD outline drawings available on "Control Product D" portal SNC0046 F0000 Screw Clamp Terminal Blocks mm² AWG mm 0.47 in Spacing Ordering Details Color Grey Blue Grey Blue Type ZS ZS-BL Order Code SNKR0000 SNKR0000 EAN Code Pack (ing) Weight ( pce) g.4.4 Yellow Yellow ZS-YL SNK60R CE CB RoHs USR CNR CSA GOST R ATEX IECEx BV ATEX Declaration

2 CE CB RoHs USR CNR CE CB RoHs USR CNR SND08C* SND600A0* SND04F0* SND64A0* CSA CSA SND670A0* GOST R GOST R SND60A* ATEX ATEX SND604A7* IECEx IECEx SND60A7* BV BV SND67A0* Atex Declaration Atex Declaration SND08C* Explosive Atmosphere: ATEX Classification Group Category IM II GD Ex eb I/II/IIIC Protection Method Ex e: increased security In the presence of explosive dust atmosphere, terminal blocks are to be installed in certified enclosure II D General Information The following information must be strictly adhered to in order to guarantee the terminal block electrical, mechanical and environmental performance. Protection Rail Wire stripping length IEC TH -7., TH - Denudage IP TH -7., TH -. mm NEMA0 0. in Operating tool Torque Flat screwdriver Tete de viscouple Screw clamp Flat screwdriver. mm.8 N.m ± 0. N.m 0.7 in. lb.in ±.77 lb.in Screw rail contact (Maximum value) Disconnect device Material Specifications Insulating material CTI Flammability Polyamide 600 V UL4 V0 NF F 6 IF Connecting capacity per clamp Rigid - Solid / Stranded conductor Flexible conductor Flexible conductor with non insulated ferrule Flexible conductor with insulated ferrule Gauge Ferrule maximum outer diameter or conductor insulation maximum outer diameter Needle flame test IEC Screw clamp IEC UL mm² 4... AWG IEC mm² mm² AWG mm² AWG A6-B6 6.4 mm IEC Compliant Ferrule.6 mm The "Connecting capacity with ferrule" data is guaranteed with ABB crimping tool PS- (crimping capacity up to mm²). Technical Datasheet SNK668D0 ABB

3 Multi Connecting capacity per clamp Rigid - Solid / Stranded conductors Flexible conductors Flexible conductors with twin ferrule IEC mm² IEC mm² mm² Don't mix solid and flexible conductors in the same clamp UL... AWG... AWG Don't mix solid or flexible conductors of different sizes in the same clamp The "Connecting capacity with ferrule" data is guaranteed with ABB crimping tool PS- (crimping capacity up to mm²) Cross section Rated cross section IEC mm² UL AWG Maximum Cross section mm² AWG Electrical characteristics Current Rated current Maximum Exe current Rated short-time withstand current s (Icw) Short-time withstand current Field and factory wiring Cat. Factory wiring Cat. 0. s s s 0 s min IEC A UL 0 A UL CSA-C-. n 8 0 A IEC/EN A IEC A Rated short-circuit withstand current CSA-C-. n 8 Max. current (4 temperature increase) / Max. cross section (mm²) A Maximum short circuit current (s) A mm² Short Circuit Current Rating (SCCR) SA UL supplement SCCR With the following configurations: Suitable conductor wire range Maximum voltage Fuse class / Max. amp. Rating UL 0 ka... AWG 600 V J 0 A T 0 A RK 0 A RK 0 A G 60 A CC 0 A Voltage Rated voltage IEC V Rated voltage UL 600 V Use Group UL B, C Rated voltage CSA-C-. n V Rated voltage Ex e IEC/ EN V Rated impulse withstand voltage IEC V Dielectric test voltage IEC V Pollution degree IEC Overvoltage category IEC III ABB Technical Datasheet SNK668D0

4 Temperature range Ambient temperature min/max Storage C Installing C Service C F F F Current Derating curve for continuous service temperature SNK00F0000 Dissipated power Maximum dissipated power at rated current Maximum dissipated power at maximum Exe current IEC W IEC W Rated power dissipation at an ambient temperature of C - IEC Separate arrangement / Overload and short-circuit protection Separate arrangement / Exclusive short-circuit protection fuse and 4 feed-through blocks Compound arrangement / Overload and short-circuit protection Compound arrangement / Exclusive short-circuit protection fuse blocks Environmental Characteristics Additional climatic tests Dry heat Cyclic damp heat Cold Damp heat steady state IEC Compliant Temperature 0 C 6 h IEC Compliant Temperature C Relative humidity % Number of cycles ( cycle = 4h) IEC Compliant Temperature - C 6 h IEC Compliant Temperature 40 C Relative humidity % 6 h Corrosion Salt mist IEC Concentration ISO 688 SO Compliant 48 h Concentration 0. dm³ Flowing mixed gas corrosion test IEC Compliant Number of the test method Compliant 6 h % j 4 Technical Datasheet SNK668D0 ABB

5 Vibrations and shocks Sinusoidal vibrations IEC Compliant Frequency range... 0 Hz Number of cycles Acceleration 7 m/s² Functional random vibrations IEC 67 Category Class B axes Frequency range Acceleration Long life testing at increased random vibrations Category Class B axes IEC 67 Frequency range Acceleration Shock Category Class B axes IEC 67 Acceleration ZS Terminal Block Accessories Compatibility Some accessories may modify the terminal block's rating. See complete information in the accessories catalog page. Description Type Order Code Pack (ing) Weight pieces g ( pce) End Stops BAM SNK0000R End Stops End Sections Jumper Bars Jumper Bars Jumper Bars Circuit Separators Circuit Separators Test Adapters Test Adapters Test Connectors Test Connectors Protecting Cover Kits Protecting Covers Protecting Covers Tools BAZ ES4 JB- JB- JB- CS CS-R TP TP4 TC TC-R KCO CO PL PR.G PR4 PR PR0 PR.Z PR0 PS- MC MC-YL MCPA MC6 MC6-YL MC6PA MC8 MC8-YL MC8PA UMH PROCAP8 SAT6 SAT8 SAT SNK0000R0000 SNK0R0000 SNK0R0000 SNK0R0000 SNK0R0000 SNK00R0000 SNK00R0000 SNK00R0000 SNK00R0000 SNK000R0000 SNK00R0000 SNK0064R0000 SNK00604R0000 SNK006R0000 SNA64800R000 SNA6800R SNA68700R0 SNA7R000 SNA7400R700 SNA78R0400 SNK0060R0000 SNK40000R0000 SNK40004R0000 SNK4R0000 SNK000R0000 SNK004R0000 SNKR0000 SNK60000R0000 SNK60004R0000 SNK6R0000 SNK006R0000 SNK006R0000 SNK006R0000 SNK0066R0000 SNK006R ABB Technical Datasheet SNK668D0

6 SNK67D0 - PDF Contact us ABB France Low Voltage Products Division Export Department, rue Ampère Z.I. - B.P. 4 F-668 Chassieu cedex / France Tel. :+ (0)4 7 7 Fax :+ (0)4 7 Note We reserve the right to make technical changes or modify the contents of this document without prior notice. With regard to purchase orders, the agreed particulars shall prevail. ABB does not accept any responsibility whatsoever for potential errors or possible lack of information in this document. We reserve all rights in this document and in the subject matter and illustrations contained therein. Any reproduction, disclosure to third parties written consent of ABB. Copyright ABB All rights reserved