Operating Instructions Display, graphic. Numeric language

Transcription

1 Operating Instructions Display, graphic Numeric language

2

3 Contents Numeric language, general... 1 Numeric language, general... 1 Display control stalk... 1 Text strings... 1 Stop message... 2 Change language... 3 Change language... 3 Menus... 5 General... 5 Password protected menus... 5 Menus available when driving... 6 Menus when vehicle stationary Numerical conversion table General Index... 29

4

5 Numeric language, general 1 Numeric language, general The instruction describes how the numeric language is made up and functions. Only the most important menus and messages are described. For more in depth information about the display see Operating instructions Display, graphic. Display control stalk Manual communication with the display is achieved using the control stalk on the right-hand side of the steering wheel. The following commands are available: 1 Esc is used to return to the previous menu and to cancel a setting /operation. 2 SELECT confirms the selected choice of menu or symbol. 3 moves the cursor up and is used to set numbers/characters. 4 moves the cursor up and is used to set numbers / characters. T Text strings Numbers between the symbols << and >> symbolise a text string. For information about what the numerical text means, see Menus page 5 17 or Numerical conversion table page <<1003>> -2 C CC 98 C 11:45 AM km

6 2 Numeric language, general Stop message Red stop lamp + stop symbol If the red stop lamp and the stop symbol are displayed the vehicle should be stopped immediately and the engine switched off. The associated numerical text should be read in order to establish where the fault lies. For information about what the numerical text means, see Menus page 5 17 or Numerical conversion table page If the engine is running a warning signal also sounds. It can be acknowledged by pressing Esc, but starts again after 10 seconds. For more in depth information about the messages see Operating instructions Display, graphic. Information lamp CHECK + text When the information lamp CHECK lights up, the fault should be checked at the next stop. The associated numerical text is shown in the display. A result of measurement is also shown for some symbols. For information about what the numerical text means, see Menus page 5 17 or Numerical conversion table page T T WARNING The vehicle must be stopped immediately and the engine must be turned off when this lamp lights up. T

7 Change language 3 Change language The numerical language is a choice and can be shown as one of three languages in the display. The language can be changed in menu Display settings. P-heater timer 2/7 Display settings Vehicle Settings Diagnostics Service Data log Password CC km

8 4 Change language Language MENU: Display setting, Language The language settings apply even after the ignition has been switched off. 1 Select Language with / and press on SET. Display settings Language Units Time/date Display lighting Change password CC km 2 Up to three languages can be displayed. Mark Numerical, which indicates the numeric language, using / and press SELECT. Press Esc to exit settings and return to the Main menu. Display settings Language 1/3 Numerical Swedish English CC km

9 Menus 5 General The numerical language has a hierarchical structure and follows the same structure as in Driver instruction Display, graphic. In those menus which have text, the text is marked with numbers. The menu explanation gives all menu headings and associated text strings. Password protected menus The key symbol to the right in the menu list means that the menu is password protected. For more in depth information about the passwords see Operating instructions Display, graphic. T

10 6 Menus Menus available when driving Menu 1 <<100>> = Gauge External temperature Temperature, engine oil Temperature, gearbox Volt meter/ Ammeter Gear selection Pressure, primary tank Menu 2 <<101>> = Fuel data Fuel consumption Resetting, fuel data <<400>> = Reset ALL fuel data? Press SELECT for 1 second. Leg fuel Resetting, fuel data <<400>> = Reset ALL fuel data? Press SELECT for 1 second. Remaining fuel

11 Menus 7 Menu 3 <<102>> = Time/distance Trip meter Reset the tripmeter <<403>> = Reset? Press SELECT for 1 second. Average speed Reset average speed <<403>> = Reset? Press SELECT for 1 second. Estimated time of arrival Give distance to destination <<405>> = Give distance: Time and date Setting, time and date Alarm clock Setting, alarm clock <<301>> = ON <<302>> = OFF <<303>> = NEW TIME Menu 4 <<103>> = Display <<304>> = Black panel <<306>> = Background lighting Setting, background lighting <<307>> = Favourite Display, setting <<308>> = Night/day Menu 5 <<104>> = Vehicle messages <<309>> = No messages

12 8 Menus MID 128 = Engine system MID 136 = Brake system MID 130 = Gearbox system MID 223 = Gear selector system MID 222 = Retarder system MID 144 = Vehicle system MID 140 = Info display system MID 150 = Air suspension system MID 249 = Bodybuilder system MID 146 = Climate system MID 232 = Airbag system MID 219 = Adaptive cruise control MID 216 = Light control system MID 231 = Telephone MID 163 = Immobilizer MID 179 = FMS Gateway MID 203 = Transp info system MID 250 = Steering Wheel Module MID 166 = Tyre pressure <<1000>> = No data <<1001>> = HIGH <<1002>> = TOO HIGH <<1003>> = Icy conditions <<1004>> = Discharge <<1005>> = Refuel now. <<1007>> = LOW <<1008>> = TOO LOW <<1009>> = Check <<1010>> = Check at next stop

13 Menus 9 <<1011>> = Stop, fault <<1012>> = Check data link <<1013>> = Check data link open circuit <<1014>> = Low pressure Menu 6 <<1040>> = Tyre pressure <<1041>> = Truck <<1042>> = Trailer 1 <<1043>> = Trailer 2 <<1044>> = Trailer 3 <<1045>> = Trailer 4 <<1046>> = Trailer 5 Menu 7 <<105>> = Reset <<406>> = Reset ALL data? Press SELECT for 1 second.

14 10 Menus Menus when vehicle stationary Menu 8 <<107>> = P-heater timer <<212>> = Program <<356>> = Set start date <<418>> = Set start time <<502>> = Set duration <<213>> = Reset <<214>> = No time programmed Menu 9 <<108>> = Display setting <<200>> = Language Numerical = Numeric language Swedish English <<201>> = Units <<310>> = Distance km miles <<311>> = Fuel consumption km/l L/100km mpg (IMP gallons) mpg (US gallons) <<312>> = Temperature C F <<359>> = Pressure

15 Menus 11 psi bar <<202>> = Time/Date <<313>> = Clock Format <<409>> = 24 h <<410>> = AM/PM <<314>> = Date format <<411>> = yymmdd <<412>> = ddmmyy <<413>> = mmddyy <<203>> = Display lighting <<315>> = Contrast <<316>> = Background lighting <<317>> = Night display <<1023>> = Inactive <<1024>> = Active <<204>> = Enter new password <<227>> = To see more menus, enter password <<319>> = Workshop password 2 <<318>> = Transport company password <<320>> = Workshop password 1 <<414>> = Enter new password: Menu 10 <<109>> = Vehicle Settings <<205>> = Traction control <<301>> = On <<302>> = Off <<206>> = Fleet target

16 12 Menus <<321>> = Engine speed (max) <<415>> = Present value: <<416>> = Enter new value: rpm <<1015>> = The transfer is complete. <<1016>> = Action unsuccessful. <<322>> = Road speed (max) <<415>> = Present value: <<416>> = Enter new value: km/h, mph <<1015>> = The transfer is complete. <<1016>> = Action unsuccessful. <<323>> = Fuel (target) <<415>> = Present value: <<416>> = Enter new value: l/100 km, mpg <<1015>> = The transfer is complete. <<1016>> = Action unsuccessful. <<207>> = Ammeter calibration <<417>> = Switch off all power consumers, then switch off the ignition. <<500>> = Calibration in progress, please wait <<501>> = Sensor component modified. Switch the ignition on. <<208>> = Fleet ID <<324>> = Fleet id: <<325>> = Enter new fleet id: <<1015>> = The transfer is complete. <<1016>> = Action unsuccessful. <<211>> = Daytime running lights <<301>> = On

17 Menus 13 <<302>> = Off <<284>> = Draining/priming <<1048>> = Set wheel ID <<1047>> = Set reference pressure Menu 11 <<110>> = Diagnostics <<215>> = Fault Diagnostics MID 128 = Engine system MID 136 = Brake system MID 130 = Gearbox system MID 223 = Gear selector system MID 222 = Retarder system MID 144 = Vehicle system MID 140 = Info display system MID 150 = Air suspension system MID 249 = Bodybuilder system MID 184 = Rear axle steering MID 214 = Burglar alarm system MID 146 = Climate system MID 232 = Airbag system MID 219 = Adaptive cruise control MID 216 = Light control system MID 231 = Telephone MID 219 = FMS Gateway MID 163 = Immobilizer MID 203 = Transp info system MID 220 = Tachograph MID 166 = Tyre pressure system

18 14 Menus <<1017>> = Data transfer in progress, please wait. <<419>> = No errors <<1016>> = Action unsuccessful <<420>> = Inactive <<421>> = Active <<423>> = More info? Press SELECT <<422>> = Number of events: <<503>> = First <<504>> = Last AM PM <<505>> = Reset? Hold SELECT for 1 second <<424>> = Reset all faults for this MID? Press SELECT for 1 second <<216>> = Instrument test <<326>> = Indicator lamp test <<327>> = Gauge test <<328>> = Display test <<329>> = Loudspeaker test <<217>> = Part number MID 128 = Engine system MID 136 = Brake system MID 130 = Gearbox system MID 223 = Gear selector system MID 222 = Retarder system MID 144 = Vehicle system MID 140 = Info display system MID 150 = Air suspension system MID 249 = Bodybuilder system MID 184 = Rear axle steering

19 Menus 15 MID 214 = Burglar alarm system MID 146 = Climate system MID 232 = Airbag system MID 219 = Adaptive cruise control MID 216 = Light control system MID 231 = Telephone MID 179 = FMS Gateway MID 163 = Immobilizer MID 203 = Transp info system MID 220 = Digital tachograph MID 166 = Tyre pressure system <<1017>> = Data transfer in progress, please wait. <<430>> = Hardware number: <<431>> = Software number: <<1018>> = No data Menu 12 <<111>> = Vehicle data <<221>> = Oil level <<331>> = min< <<332>> = >max <<330>> = Not available. X min remaining. <<222>> = Load indicator <<228>> = Brake lining, status

20 16 Menus Menu 13 <<112>> = Data log <<223>> = Vehicle number <<1017>> = Data transfer in progress, please wait <<333>> = Fleet id: <<334>> = Chassis number: <<1018>> = No data <<224>> = Totals <<335>> = Total distance: <<336>> = Total fuel consumption: <<337>> = Total number of hours engine has been run: <<338>> = Total idling time: <<339>> = Total power take off time: <<340>> = Total number of engine revolutions: <<225>> = Trip data <<341>> = Trip distance: <<342>> = Trip average fuel consumption: <<343>> = Trip total fuel consumption: <<344>> = Trip overrevs: <<345>> = Trip uneconomic revs: <<346>> = Trip consumption during uneconomic revs: <<347>> = Trip average fuel consumption: <<348>> = Trip overspeed: <<349>> = Trip engine hours: <<350>> = Trip idling time: <<351>> = Trip idle fuel consumption: <<352>> = Trip power take-off time: <<353>> = Trip power take-off fuel <<354>> = Trip cruise time

21 Menus 17 <<226>> = Reset Trip data <<433>> = Reset all trip data? Press SELECT for 1 second. <<1017>> = Data transfer in progress, please wait <<1015>> = The transfer is complete. <<1016>> = Action unsuccessful Menu 14 <<113>> = Password Entering, password <<227>> = For more menus, enter password:

22 18 Numerical conversion table General In order to quickly see what each number means here is a list of all numbers in order together with the meaning. <<100>> to <<113>> Number Meaning 100 Gauge 101 Fuel data 102 Time/distance 103 Display 104 Vehicle messages 105 Reset 107 P-heater timer 108 Display setting 109 Vehicle Settings 110 Diagnostics 111 Vehicle data 112 Data log 113 Password <<200>> to <<284>> Number Meaning 200 Language 201 Units 202 Time/Date 203 Display lighting 204 Change password 205 Traction control 206 Fleet target 207 Ammeter calibration

23 Numerical conversion table Fleet id 209 Fog lights 210 Spotlights 211 Daytime running lights 212 Program 213 Reset 214 No time programmed 215 Fault diagnostics 216 Instrument test 217 Part number 218 General enquiry 219 Other systems 220 Reset all 221 Oil level 222 Load indicator 223 Vehicle number 224 Totals 225 Trip data 226 Reset trip data 227 For more menus, enter password: 284 Draining/priming <<300>> to <<358>> Number Meaning On 302 Off 303 New time 304 Black Panel 305 Favourite Display

24 20 Numerical conversion table 306 Background lighting 307 Favourite Display, setting 308 Night/day 309 No messages 310 Distance 311 Fuel consumption 312 Temperature 313 Clock Format 314 Date format 315 Contrast 316 Background lighting 317 Night display 318 Transport company, password 319 Workshop, password Workshop, password Engine speed (max) 322 Road speed (max) 323 Fuel (target) 324 Fleet id 325 Enter new fleet id 326 Indicator lamp test 327 Gauge test 328 Display test 329 Loudspeaker test 330 Not available. X min remaining. 331 min< 332 >max 333 Fleet id: 334 Chassis number:

25 Numerical conversion table Total distance: 336 Total fuel consumption: 337 Total number of hours engine has been run: 338 Total idling time: 339 Total power take off time: 340 Total number of engine revolutions: 341 Trip distance: 342 Trip average fuel consumption: 343 Trip total fuel consumption: 344 Trip overrevs: 345 Trip uneconomic revs: 346 Trip consumption during uneconomic revs: 347 Trip average fuel consumption: 348 Trip overspeed: 349 Trip engine hours: 350 Trip idling time: 351 Trip idle fuel consumption 352 Trip power take-off time: 353 Trip power take-off fuel: 354 Trip cruise time: 355 Incorrect password. 356 Set start date 357 Draining/priming requested 358 Draining/priming not allowed <<400>> to <<434>> Number Meaning 400 Reset ALL fuel data? Press SELECT for 1 second 403 Reset? Press SELECT for 1 second. 405 Give distance:

26 22 Numerical conversion table 406 Reset ALL data? Press SELECT for 1 second h 410 AM/PM 411 yymmdd 412 ddmmyy 413 mmddyy 414 Enter new password: 415 Present value: 416 Enter new value: 417 Switch off all power consumers, then switch off the ignition. 418 Set start time: 419 No errors 420 Inactive 421 Active 422 Number of events: 423 More info? Press SELECT 424 Reset all faults for this MID? Press SELECT for 1 second. 425 Reset ALL faults? Press SELECT for 1 second. 426 Alarm 427 Alarm clock 428 Warning 429 Turn indicators 430 Hardware number: 431 Software number: 432 Give over speed 433 Reset all trip data? Press SELECT for 1 second. 434 No other systems accessible.

27 Numerical conversion table 23 <<500>> to <<506>> Number Meaning 500 Calibration in progress, please wait 501 Sensor component changed. Switch on the ignition 502 Set duration: 503 First: 504 Last: 505 Reset? Hold SELECT for 1 second. 506 Too many fault messages <<1000>> to <<1096>> Number Meaning 1000 No data 1001 High 1002 Too high 1003 Icy conditions 1004 Discharge 1005 Refuel now 1007 Low 1008 Too low 1009 Check 1010 Check at next stop 1011 Stop. Fault Check data link 1013 Check data link open circuit 1014 Low pressure 1015 The transfer is complete 1016 Action unsuccessful Data transfer in progress, please wait.

28 24 Numerical conversion table 1018 No data 1019 Welcome 1020 Pleasant journey! 1021 Incorrect password 1022 ACC, radar obscured 1023 Inactive 1024 Active 1025 ACC radar warming up 1026 ACC datalink problem 1027 Service of brake linings at: 1028 Brake linings are new Brake linings need service Disabling idle 1031 Disabling idle, cancelled 1032 Disabling of vehicle started 1033 Vehicle disabled 1034 Trailer, door locked 1035 Trailer, door unlocked 1036 Load, safety system enabled 1037 Load, safety system disabled 1038 Calibration: 1039 Too high vehicle speed. Disable PTO before proceeding 1040 Tyre pressure 1041 Truck 1042 Trailer Trailer Trailer Trailer Trailer 5

29 Numerical conversion table Set reference pressure 1048 Set wheel ID 1049 Enter new settings 1050 Select axle number 1051 Current value 1052 New value 1053 Set wheel ID 1054 Enter axle and wheel 1055 Current ID 1056 New ID 1057 No data 1058 Starter motor, overheating alarm 1059 Starter motor, gearbox not in neutral 1060 Starter motor, gear wheel sync Start not possible, PTO enabled 1062 Stabilization, ACC sensor 1063 Reversing light trailer 1064 Fog light front 1065 Fog light rear 1066 Spotlight 1067 Reversing lights 1068 Brake lights 1069 Brake lights trailer 1070 Direction indicators, front 1071 Direction indicators, rear 1072 Direction indicators, trailer 1073 Parking lights 1074 Parking lights trailer 1075 Snow plough light

30 26 Numerical conversion table 1076 Check fuses 1077 Reduced light 1078 Brake light, reduced 1079 High beam 1080 Dipped beam 1081 No data, TPM 1082 Interior lighting 1085 Wait with start 1088 Select a lower gear 1089 Test SW installed in 1090 Reduced EGR system 1091 High pressure in diesel particulate filter 1092 Reduce charge pressure 1093 Reduce charge temp 1094 Vehicle safety mode 1096 LDWS disabled. Clean windscreen MID 128 to MID 250 Number MID 128 MID 130 MID 136 MID 140 MID 144 MID 146 MID 150 MID 163 MID 166 MID 179 MID 184 Meaning Engine system Gearbox system Brake system Info display system Vehicle system Climate system Air suspension system Immobilizer Tyre pressure system FMS Gateway Rear axle steering

31 Numerical conversion table 27 MID 203 MID 214 MID 216 MID 219 MID 222 MID 223 MID 231 MID 232 MID 249 MID 250 Transp. info system Burglar alarm system Lighting system Adaptive cruise control Retarder system Gear selector system Telephone Airbag system Body builder system Steering Wheel Module

32

33 Index 29 Index C Change language... 3 Control stalk... 1 D Display control stalk... 1 M Menus... 5 N Numeric language, general... 1 Numerical conversion table P R S T Password protected menus... 5 Red stop lamp + stop symbol... 2 Stop message... 2 Text strings... 1 The information lamp CHECK + text... 2

34 Volvo Truck Corporation Göteborg, Sweden English