Fire Control Panels. Remote Annunciator Panels. UL, ULC, CSFM Listed; FM Approved; MEA (NYC) Acceptance* Features. Introduction

Transcription

1 Emergency Operating Instructions Fire Alarm S Priority 2 Alarm Fire Alarm Priority 2 Ack Ack How Acknowledge / View Events Press ACK located under flashing indicar. Repeat operation until all events are acknowledged. Local ne will silence. System Supervisory System Trouble Supv Trouble Ack Ack WARNINGS Alarm or Warning Condition System indicar flashing. Tone. How Silence Building Signals Press Alarm Silence. Alarm Silenced Alarm Silence AC Power System Reset Page Up Previous Next Page Dn How Reset System Press System Reset. Press Ack silence ne device. A B C D E F G H I ZONE 1 J K L M N O P Q R FB 4 S T U V W X Y Z / P 7 'SP' ( ), # : NET Menu SIG AUX 2 3 IO 5 A 8 IDNet 6 L 9 ADDR 0 C/Exit Enter Fire Panels UL, ULC, CSFM Listed; FM Approved; MEA (NYC) Acceptance* Features Remote Annunciar Panels provide fire alarm control panel status information at locations distant from the fire alarm control panel Typical functions include: Remote status LED indicars and dedicated switch input controls located on LED/switch modules Remote status LED indicar modules with 8 red or 16 (8 red/8 yellow) that are pluggable allow color selection (yellow, green, or red are ordered separately) Remote microphone and operar interface for access the emergency voice/alarm communications system Remote master telephone for communicating the firefighter telephone system Also available with InfoAlarm expanded content user interface (refer page 5 and data sheet S for additional information) Additional optional modules include: Remote module for LCD status readout and keyswitch controlled functions 24 Point I/O module RS-232 ports for remote printer or terminal connections Power supplies with battery charger for annunciar Panel mounted printer for system status recording Wiring requirements: RUI or RUI+ (remote unit interface) supervised communications from the host fire alarm control panel provide Style 4 or Style 7 SLC (signaling line circuit) connections Microphone and telephone circuits require their own dedicated wiring Listed : UL Std. 864, Fire Detection and (UOJZ), and Smoke Service (UUKL) UL Std. 2017, Process Management Equipment (QVAX) UL Std. 1076, Proprietary Alarm Units-Burglar (APOU) UL Std. 1730, Smoke Detecr Monir (UULH) ULC Std. S * See page 4 for additional listing details. This product has been approved by the California State Fire Marshal (CSFM) pursuant Section of the California Health and Safety Code. See CSFM Listing :0251 for allowable values and/or conditions concerning material presented in this document. Additional listings may be applicable; contact your local Simplex product supplier for the latest status. Listings and approvals under Simplex Time Recorder Co. are the property of Tyco Fire Protection Products. 4100ES Remote Annunciar in a Three Bay Cabinet with Operar Modules; Remote (left) and with an InfoAlarm (right) Introduction Remote Annunciar Panels Remote Annunciar Panels are dedicated purpose transponders that support fire alarm system status information. Typical use is when the host fire alarm control panel is located away from the area where those responding a fire situation need status information. Status and. s are suitable for firefighter or other fire brigade responders access particular information and for system control. When equipped with a remote microphone and emergency voice/alarm communications system control, an authorized user can take command of the system and either play selected pre-recorded messages or select specific nes, or initiate live broadcast information either globally in the system, or selected areas. Remote Master Firefighter. When equipped with a remote master phone, the authorized user can connect remote phone call-in requests and allow callers be connected each other. Although intended for use in assisting fire responders, these system are also helpful during system setup and test. S /2013

2 Module Bay Description Remote Annunciars include a bay assembly, a power distribution interface module (PDI), a Transponder Interface Module, and an interconnect harness. Communications with the host fire alarm control panel are via a Remote Unit Interface (RUI or RUI+) connection that allows for up 2500 ft (762 m) distance. RUI can communicate with up a tal of 31 remote devices per master controller (on one or multiple RUI channels) and can be either Style 4 or Style 7 communications. Wiring can be either shielded or unshielded, twisted, or untwisted single pair wiring Remote Annunciar. This model is for applications that may require a full complement of the Remote Annunciar functions (refer the product selection lists on pages 3 and 4). Power is from a cabinet mounted Remote Power Supply (RPS) Basic Remote Annunciar. For remote annunciar applications that require less features in the cabinet, select this model which accepts power from a separate fire alarm control cabinet. (This model does NOT accept: a cabinet mounted power supply, expansion phone cards, Class A phone modules, RS-232 modules, panel mounted printers, or 24 I/O modules.) Optional Expansion Bays each include a PDI and accept a variety of optional modules for specific annunciar functions. The Battery Compartment (botm) accepts two batteries, up 50 Ah. Battery mounting does not interfere with available module space. (Not applicable the model ) Remote Annunciar Module Reference Packaging Availability Modules are power-limited (except as noted, such as relay modules) Enclosure are available for one, two, or three bay sizes or for cabinet rack mounting Boxes, doors with tempered glass inserts, and dress panels are available in beige or red (ordered separately) Refer document S for enclosure details Remote The optional Remote occupies the p bay of a Remote Annunciar. It provides an LCD status readout with keyswitch activated control switches and a local ne-alert sounder. Features are essentially identical the Remote LCD Annunciar model (reference document S ). REMOTE COMMAND CENTER Emergency Operating Instructions FIRE ACK PRIORITY 2 ACK SYSTEM SUPERVISORY SUPV ACK SYSTEM TROUBLE TBL ACK Alarm or Warning Condition System indicar flashing. Tone. How Acknowledge / View Events Press ACK located under flashing indicar. Repeat operation until all events are acknowledged. Local ne will silence. POWER ON SILENCED SILENCE Remote DISPLAY TIME SYSTEM RESET How Silence Building Signals Press Alarm Silence. How Reset System Press System Reset. Press Ack silence ne device. Circuits Circuit 1 Circuit 9 8th Circuit 2 Circuit 10 7th Circuit 3 Circuit 11 6th Push-- switch Circuit 4 Circuit 12 5th Circuit 5 Circuit 13 4th Circuit 6 Circuit 14 3rd Circuit 7 Circuit 15 2nd Circuit 8 Circuit 16 1st Remote Master Module Switches with 8 Red, , 2 shown with typical labels Remote Microphone Module Single Channel Switches with 8 Red, S /2013

3 Product Selection Panel Type Model Description Details and Mounting Reference Remote Annunciar Panel; requires an internal power supply Basic Remote Annunciar Panel; requires power from another cabinet (refer module exclusion list on page 2) Includes a bay assembly with power distribution board, a Basic Transponder Interface Module ( ) mounted in Block A, and an interconnect harness for connecting 4100ES/4100U Slot modules Supervisory and Alarm current = 87 ma Includes a bay assembly with power distribution board, a remotely powered Transponder Interface Module mounted in Block A, and an interconnect harness for connecting 4100ES/4100U Slot modules Supervisory and Alarm current = 87 ma Remote Option (for InfoAlarm expanded content display products, refer data sheet S ) Model Description Details and Mounting Reference Panel Mounted LCD Annunciar; 2 line by 40 character LCD with LED illumination; LED illumination is off during supervisory, turning on with alarm or when switches are activated Mounting requires the p bay; 4100ES/4100U flat modules are allowed behind it; RUI device, RUI/RUI+ connection is required Supervisory current = 65 ma (w/o backlight) Alarm current = 140 ma Emergency Voice/Alarm Communications Operar Interface Options Model Description Details and Mounting Reference Remote Microphone (mike) Module Front panel module; requires 2 Slots (4 [51 mm]), space behind accepts 4100ES/4100U flat modules only (requires dedicated wiring fire alarm control panel audio control module); Supv. = 2.4 ma, = 6 ma Channel (audio or mike) Single slot modules requiring connection an LED/switch controller; space Channel (audio + mike) Operar behind accepts 4100ES/4100U flat modules only; adjacent LED/switch Interface module(s) are required for specific speaker circuit selection (refer Channel (full audio) Modules document S for audio reference and document S for Channel LED/switch module reference); Supv. = 0, Alarm = 24 ma Firefighter Telephone System Products (refer document S for additional detail) Model Description Details and Mounting Reference Remote Master Telephone Mounts in two vertical blocks of bay front, locate as required; space behind allows 4100ES/4100U flat modules only Module with 3 Class B phone NACs Single Block module, mounts bay mounting plate Not available Class A Adapter Module Mounts , no additional space required with LED and LED/Switch Modules, General Purpose (LED/switch controller and label kit is ordered separately)* per Switch Switches Model LED Color(s) Model LED Color(s) e Red Yellow Two Red on p, Yellow on botm Yellow, p and botm Two Red on p, on botm on p, Yellow on botm e Red Red on left, 8 Yellow on right per Switch Switches Model LED Color(s) only 8 only Red, pluggable only 16 only Pluggable, shipped Red on p, Yellow on botm e Pluggable, shipped Red on p, Yellow on botm; Note: UL, ULC, and CSFM listed only e Red LED/Switch Modules, Special Purpose (LED/switch controller, label kit, and separate are ordered separately)* Model Operation Switch Function (Location) LED Description (p) LED Eight function HOA (,, ) Module (middle) Red LED with labeled switches (botm) LED Eight function HOA (,, ) Module, same as except switches are unlabeled LED/Switch ler Modules and Accessories (LED kits for /1277/1300 are on page 4)* Model Description 64 LED/64 Switch ler Module with mounting plate; controls up 64 and interfaces up 64 switches; mounts behind the LED/switch modules and has provisions for one ler Module 64 LED/64 Switch ler Module without mounting plate; mounts on extra space of ; controls an additional 64 and 64 switches NOTE: LED/switch controllers and their connected LED/switch modules must be in the same bay; (see data sheet S for details) LED/Switch Module Slide-in Labels, required when LED/switch modules are present; order one per cabinet Point I/O Module for external connections, select each point as either input or output; 2 (51 mm) wide, 1 Slot; refer S for more detail; not available with * Note: Refer data sheet S for additional LED/Switch module selections. (continued) 3 S /2013

4 Product Selection (Continued) Communication Modules (not available with ) Model Description Size Supv. Alarm Dual RS-232 Interface, mounts in Slot 3 or Slot 2 1 Slot 132 ma 132 ma Master Clock Interface Module with one standard RS-232 port (see S ) 1 Slot 132 ma 132 ma Panel Mounted Printer (not available with , refer document S for additional detail) Model Description Panel Mount Thermal Printhead Printer, supplied with one roll of paper; requires 3 expansion slots Replacement Paper for Printer, one roll Power Supplies and Accessories Model Voltage/Listing Description Size Supv. Alarm VAC UL Remote Power Supply (RPS); 9 A power supply VAC, Canadian ULC with battery charger; Canadian model has low battery cuut; required for , not /230/240 VAC UL available with Blocks 150 ma 185 ma Box Interconnection Harness Kit; order one for each close-nippled cabinet; also used if power is supplied from host fire alarm control panel Power Distribution Modules Model Voltage Description VAC 220/230/240 VAC Power Distribution Module (PDM); select per system voltage Miscellaneous Accessories Required for , select one per box or cabinet rack; not applicable for Model Description Expansion Bay Hardware, order one for each expansion bay (unless included with selected option) Single blank 2 display cover, order as required (8 fill a bay front); 2 max. between LED/switch modules Termination and Address Label Kit (for module marking); provides additional labels for field installed modules Terminal Block Utility Module; provides 2, 16 position terminal blocks mounted on 4 x 5 single block size, capable of up 12 AWG wire (3.31 mm 2 ) Door Tamper Switch (connects Transponder Interface Module) Yellow Red General Specifications Input Power Kits of 8 ; order as required for /1277/1300 modules Remote Power Supplies (RPS) 120 VAC Models 4 A VAC, 60 Hz VAC Models 2 A VAC, 50/60 Hz; separate taps for 220/230/240 VAC Power Supply Output Ratings for the Remote Power Supply (RPS) Total Power Supply Output Rating Auxiliary Power Tap NACs Programmed for Auxiliary Power 9 A nominal 28 VDC, including module currents and auxiliary power outputs 2 A maximum 2 A maximum per NAC, 5 A maximum tal Battery Charger, Remote Power Supply (RPS) (sealed lead-acid batteries) Battery capacity range Charger characteristics and performance Environmental Rated VDC Output switches battery backup during mains AC failure or brownout conditions UL listed for battery charging of 6.2 Ah up 110 Ah (batteries larger than 50 Ah require a remote battery cabinet); ULC listed for charging up 50 Ah batteries Temperature compensated, dual rate, recharges depleted batteries within 48 hours per UL Standard 864, 70% capacity in 12 hours per ULC Standard S527 Operating Temperature Range F (0 49 C) Operating Humidity Range Up 93% RH, 90 F (32 C) maximum 4 S /2013

5 5 S /2013 Fire Zones Fan Fan HVAC s HVAC s Door Release Manual Alarms Smoke Alarms Two Bay Remote Annunciar LED/Switch Module Reference InfoAlarm Detail Reference

6 Single Slot LED/Switch Module Detail Reference LED/Switch Modules Label insert Primary function label LED Modules Additional function labels Switches Cusm label area Fan Fan Designates area for each column of switches and Visible area 8-1/4" H, 2" W (210 mm x 51 mm) Switch LED Color Legend: Red, Yellow, ; R/Y = Red on p, Yellow on botm; R-Y = Red on left, Yellow on right 8 Switches with 16 : , R/Y , Y/Y , R/G , G/Y 16 Switches with 16 : , R/Y (pluggable ) 8 Switches with 8 : , R , Y 16 Switches with 16 : , R-Y , R 8 : , R (pluggable ) 16 : , R/Y (pluggable ) Dual Slot LED/Switch Module Detail Reference Label insert e switch per control, on/off Primary function labels Cusm label area LED () Red LED () LED () Red Visible area 8 1/4" H, 2" W (210 mm x 51 mm) e switch per function Switches, 24 HOA Modules, 8 s (3 switches each), 24 : , with labeled switches (shown) , with unlabeled switches (not shown) 6 S /2013

7 Module Detail , Single Channel , 1.5 Channel , Dual Channel , 3-8 Channel LED LED LED LED Visible area 8-1/4" H, 2" W (210 mm x 51 mm) Red Alert Red Alert Red Start Selected Red Local Local Local Local Alert Expansion Bay Module Loading Reference Blank switches can be programmed as required Slot 1 Slot 2 Slot 3 Slot 4 Slot 5 Slot 6 Slot 7 Slot 8 Block A Block C Block E Block G Size Definitions: Block = 4 W x 5 H card area Slot = 2 W x 8 H motherboard with daughter card Block B Block D Block F Block H Expansion Bay Chassis Additional 4100ES Data Sheet Reference Subject Data Sheet Subject Data Sheet 4100ES Panels S LED/Switch Modules S InfoAlarm With EPS S ES Basic Panel Modules S Power Network Display Unit (NDU) Supplies S MINIPLEX Transponders S MINIPLEX Transponders S Network Display Unit (NDU) S Enclosures S Remote Battery Charger S ES/4100U / Modules S S /2013

8 Wall Mounted Enclosure Installation Reference Front view, box outline without door Side view with door attached 3 Bay height = 56" (1422 mm) Door thickness 4-3/4"(121 mm) Knockout screw/nail holes (for semi-flush mounting) 2 Bay height = 40" (1016 mm) Exposed cabinet for semi-flush mounting 1-3/8" (35 mm) minimum Wall board reference for semi-flush mounting, 6" stud 1 Bay height = 22" (559 mm) Doors can be hinged left or right Exposed door and cabinet for semi-flush mounting 6-1/8" (156 mm) minimum Optional semi-flush trim kit reference Stud alignment markers, each side 6" stud 4" stud 24" (610 mm) 6-29/32" (175 mm) 11-11/16" (296 mm) NOTE: A system ground must be provided for Earth Detection and transient protection devices. This connection shall be made an approved, dedicated Earth connection per NFPA 70, Article 250, and NFPA 780. TYCO, SIMPLEX, and the product names listed in this material are marks and/or registered marks. Unauthorized use is strictly prohibited. Tyco Fire Protection Products minster, MA USA S / Tyco Fire Protection Products. rights reserved. specifications and other information shown were current as of document revision date and are subject change without notice.