DALI Power Module (LQSE-2DAL-D) DALI Bus 1. DALI Bus 2. HomeWorks. Wallstation. Power. Eye QS Control Power Up to 100. Module.

Transcription

1 DAI Module E-2DA-D DAI Fixture Controller DAI Module a The DAI Module is a DI-rail mounted controller for DAI -compliant Digital Addressable loads. It provides DAI bus power and control for two independent DAI buses with up to 64 ballasts each. Features Provides power for two buses of DAI compliant digital addressable loads (up to 250 ma per bus). Each DAI Bus can control a maximum of 16 zones. failure memory retains programming in the event of a power loss. DAI Module can be used in a HomeWorks system to control and manage light in an entire home or building. DAI Module E-2DA-D (0) mm DAI Module (E-2DA-D) DAI Bus 1 DAI Bus 2 to 64 ballasts on each link DAI Module HomeWorks Wallstation HomeWorks GRAFIK 230 V~ Module Processor Eye Control to 100 ink Sivoia Shade / Drapery Contact Closure Interface total devices Supply DAI is registered trademark of ZVEI-Zentralverband Elektrotechnik Job ame: Model umbers: Job umber:

2 DAI Module E-2DA-D DAI Fixture Controller Specifications ightning strike protection meets ASI/IEEE standard Can withstand voltage surges of up to V~ and current surges of up to A. Stand by power: 7 W BTUs / hour when fully loaded: 24 DAI Bus Output: 16 V- 250 ma maximum per bus. Standards IEC utron Quality Systems registered to ISO CE C-Tick S Environment Ambient Temperature Operating Range: 0 ºC to 40 ºC. Relative Humidity: less than 90% non-condensing. Calibration point maximum: 75 ºC For indoor use only. Terminals Mains Wiring: 1,0 mm 2 to 4,0 mm 2 (18 AWG to 12 AWG) DAI Bus Wiring: 1,0 mm 2 to 4,0 mm 2 (18 AWG to 12 AWG) ink Wiring: 1,0 mm 2 (18 AWG) Mounting Intended to mount within an IP20 (minimum) rated consumer panel or breaker panel with integrated DI rail and dead cover Width = 9 DI modules (161,7 mm). Programming and Compatibility Requirements The E-2DA-D can only be used with the HomeWorks system. Setup and programming of the DAI Module is done through the HomeWorks programming software. HomeWorks software version 3.1 or higher required a DAI Buses to 64 DAI compliant loads on each bus can be addressed and grouped into 16 zones. DAI Module supplies 250 ma to power each bus. DAI Bus wires are polarity insensitive and topology-free. ink imits A link in a HomeWorks system can have up to 512 zones (outputs) and 100 devices. A ballast or driver counts as 1 zone unless specifically grouped into zones from the HomeWorks software. Each DAI Module counts as one device toward the 100 device limit. A maximum of 8 fully loaded DAI Buses may be connected to a single link. HomeWorksR Wallstations HomeWorks wallstations can be configured to control DAI Modules with the HomeWorks programming utility. ED indicator displays the status of programmed lights. Troubleshooting and Maintenance Features Maintains redundant memory of ballast programming for ease of single or multiple ballast replacement. To verify DAI lights connected to DAI bus 1 and bus 2: Enter Mode: Press and hold button on the DAI Module until the ED starts flashing. : Each press of either the DAI 1 or DAI 2 button will cycle the lights between high-end, low-end and flash for that bus. Exit Mode: Press and hold button until ED stops flashing. DAI is registered trademark of ZVEI-Zentralverband Elektrotechnik Job ame: Model umbers: Job umber:

3 DAI Module E-2DA-D DAI Fixture Controller Overview of Wiring Terminals and Mechanical Dimensions a IEC PEV / EC Class 2 ink DAI Bus 1* Rev. B DAI Bus 2* 1771 DAI Module E-2DA-D (0) ,7 mm 8 mm Mains Wiring 161,7 mm * Wire according to local codes. 60,6 mm DAI is registered trademark of ZVEI-Zentralverband Elektrotechnik EC is a registered trademark of the ational Fire Protection Association, Quincy, Massachusetts Job ame: Model umbers: Job umber:

4 8 mm DAI Module E-2DA-D DAI Fixture Controller Wiring: Mains Voltage DAI Module E-2DA-D (0) DAI Module E-2DA-D (0) mm Wiring from Distribution to Module a M E V~ Turn off all circuit breakers or isolators feeding the Module unit at the distribution panel. Run line, neutral, and earth/ground wires from a 8 mm 230 V~ 50/60 Hz feed to the DAI Module. Emergency ighting Applications Use normal (non-essential) power only to power the DAI Module. When normal power drops out, the DAI Module will not power the DAI Buses. When this occurs, ballasts powered from emergency feeds go to their emergency mode, full light output by default. Mains Wiring and IEC PEV / EC Class 2 Separation The DAI Module is designed to separate mains wiring from IEC PEV / EC Class 2 circuits. Follow appropriate local and national codes to avoid violating required separation guidelines. Distribution Panel Earth/Ground eutral Mains/ive DAI is registered trademark of ZVEI-Zentralverband Elektrotechnik EC is a registered trademark of the ational Fire Protection Association, Quincy, Massachusetts Job ame: Model umbers: Job umber:

5 8 mm DAI Module E-2DA-D DAI Fixture Controller Wiring: DAI Bus a DAI Bus 1 DAI 1 DAI 1 DAI Module E-2DA-D (0) DAI Bus 2 DAI 2 DAI 2 The DAI Module will supply power for two independent DAI Bus, which supports a maximum of 64 ballasts per bus. DAI Wiring DAI wiring is not IEC PEV/EC Class 2. DAI wiring is treated as mains voltage, and thus may be run within the same sheathing. Ensure that there is no greater than a 2 V~ drop between the DAI Module and the end of the DAI Bus. Consult all national and local electrical codes for separation requirements. Maximum DAI -compliant Wire Gauge Bus Wire ength 4,0 mm 2 (12 AWG) 671 m 2,5 mm 2 (14 AWG) 427 m 1,5 mm 2 (16 AWG) 275 m 1,0 mm 2 (18 AWG) 175 m DAI is registered trademark of ZVEI-Zentralverband Elektrotechnik EC is a registered trademark of the ational Fire Protection Association, Quincy, Massachusetts Job ame: Model umbers: Job umber:

6 8 mm DAI Module E-2DA-D DAI Fixture Controller Wiring: ink a IEC PEV / EC Class 2 ink Wiring ink communicates using IEC PEV / EC Class 2 wiring. DAI Module E-2DA-D (0) Follow all applicable national and local codes for proper circuit separation and protection. Wiring may be daisy chained or t-tapped. Total length of link must not exceed 600 m. Do OT connect terminal 2. Wire Gauge (terminals 1 and 2): 1 pair 1,0 mm( (18 AWG) Data (terminals 3 and 4): 1 pair 0,5 mm( to 1,0 mm( (20 AWG to 18 AWG) twisted and shielded Can use utron cable GRX-CB-346S-500 (1) (2) o Connection (3) (4) ower Module DA-D 50/60 Hz 80 ma com +44.(0) DAI is registered trademark of ZVEI-Zentralverband Elektrotechnik EC is a registered trademark of the ational Fire Protection Association, Quincy, Massachusetts Job ame: Model umbers: Job umber: