Using and Installing: HCS12C32 Board, HCS12C128 Board, USB-to-Serial port driver, and HyperTerminal

Size: px

Start display at page:

Download "Using and Installing: HCS12C32 Board, HCS12C128 Board, USB-to-Serial port driver, and HyperTerminal"

Briana Craig
10 years ago
Views:

1 Using and Installing: HCS12C32 Board, HCS12C128 Board, USB-to-Serial port driver, and HyperTerminal CMPEN 472, Spring 2013, Kyusun Choi Download from the PSU Angel cmpen472 page, the USB-to-Serial port driver and HyperTerminal program, and install them. First, install the USB-to-Serial port driver. My computer is Windows 8, so I choose PL-2303 Vista Windows 7 Driver Installer.exe file. Double click the file to run the Installer. (If you have Windows XP computer, choose PL-2303 Driver Installer.exe file.)

them. First, install the USB-to-Serial port driver.

3 Now Restart your computer! Open Control Panel and click on Hardware and Sound option.

4 Select Device Manager.

5 Please follow the procedures outlined below carefully. Now power-up your HCS12 board with the DC power plug or the USB type B plug. Then connect the USB-to-Serial port cable to your HCS12 board (serial port side). Plug-in the USB-to-Serial port cable (USB port side) into your computer s USB port.

plug. Then connect the USB-to-Serial port cable to your HCS12 board

6 Right click on the Prolific USB-to-Serial Comm Port (COM3). The COM3 may be different on your computer. Then select Update Driver Software option. Click on Browse my computer for driver software option.

7 Select Let me pick from a list of device drivers on my computer option. Select Prolific USB-to-Serial Comm Port Version: [2/12/2007] option.

8 Restart your computer again. You may click Yes if you are ready to restart your computer. Click No if you need to close any other applications before the restart. Be sure to restart your computer before proceeding to your CodeWarrior project.

Click No if you need to close any other applications before

After you restart your computer, you can check to see if your USB-to-Serial port driver is correctly installed. Open Control Panel and click on Hardware and Sound option.

9 After you restart your computer, you can check to see if your USB-to-Serial port driver is correctly installed. Open Control Panel and click on Hardware and Sound option. Open the Device Manager window. Plug-in the USB-to-Serial port cable into your computer s USB port. If your USB-to-Serial port driver IS correctly installed, you will still see in the Device Manager window the Prolific USB-to- Serial Comm Port (COM3) device WITHOUT the yellow exclamation mark as shown below. If your USB-to-Serial port driver is NOT correctly installed, you will see in the Device Manager window the Prolific USB-to- Serial Comm Port (COM3) device with the yellow exclamation mark as shown below. Just in case if you still have problem, you can redo the USB-to-Serial port driver installation by following steps.

If your USB-to-Serial port driver IS correctly installed, you will still see in the Device Manager window the Prolific USB-to- Serial Comm Port (COM3) device WITHOUT the yellow exclamation mark as

10 Right click on the Prolific USB-to-Serial Comm Port (COM3) device with the yellow exclamation mark, and select the Uninstall option. And un-plug the USB-to-Serial port cable from your computer s USB port. Now go to the top of this document, follow the USB-to-Serial port driver installation procedure.

And un-plug the USB-to-Serial port cable from your computer s USB port.

11 HyperTerminal Program Installation: Next task is to install the HyperTerminal program. (If you have Windows XP computer, the HyperTerminal is already installed as part of the Windows XP.) Double click on the htpe63.exe file.

Communicating HCS12 Board with HyperTerminal on your computer: Now you are ready to use your HCS12 board to do the homework! Again, please follow the procedures outlined below carefully.

16 Communicating HCS12 Board with HyperTerminal on your computer: Now you are ready to use your HCS12 board to do the homework! Again, please follow the procedures outlined below carefully. Now power-up your HCS12 board with the DC power plug or the USB type B plug. Then connect the USB-to-Serial port cable to your HCS12 board (serial port side). Plug-in the USB-to-Serial port cable (USB port side) into your computer s USB port. Start the HyperTerminal (HyperTerminal Private Edition) program, from the Start Menu or from Metro menu.

Now power-up your HCS12 board with the DC power plug or the USB type B plug.

20 Press the Reset button on your HCS12 board. Hit a return key to start the monitor program on the HCS12 board.

22 Now you can test run the HW2 program on the HCS12 board.

23 Change the Counter2 constant from $0002 to $0020, longer delay (running the program on the HCS12 board with 24MHz bus clock is about 16 times faster than the program simulation on your computer).

24 Type load command and hit the return key. Left click the Transfer menu, and select the Send Text File option.

25 Find the bin folder of your HW2 CodeWarrior project.

28 Type go 3900 command.

29 Now you should see the blinking light, of the LED2 on the HCS12C32 board or of the LED1 on the HCS12C128 board. Congratulations! This completes this guide.

PL2303HXA/XA Windows 8 Update Driver Installation. How to Update Driver to Support PL2303HXA/XA in Windows 8 Operating Systems

PL2303HXA/XA Windows 8 Update Driver Installation. How to Update Driver to Support PL2303HXA/XA in Windows 8 Operating Systems How to Update Driver to Support PL2303HXA/XA in Windows 8 Operating Systems Requirements USB Device with embedded PL2303HX (Rev A) or PL2303X (Rev A) chip version Driver Installer & Build date: 1.5.0 (10/21/2011)