LINED PIPING SYSTEMS. 1. Introduction. 2. Technical Data.

Transcription

1 RESISTOFLEX GMBH flanged pipe, fittings and hoses are all without exception lined with seamless fluorocarbon resins like PTFE (Polytetrafluorethylen) and PFA (Perfluoralcoxy). This leads to the most advanced linings which are attainable. The patented THERMOLOK-Process guarantees, in connection with years of practice and manufacturing, world-wide top quality and therefore a high factor of safety and a very long life of the installed parts. RESISTOFLEX-PTFE-linings are relaxed and braced thermally inside the housings. This compensates the different expansion factors between steel and FLUOROFLEX -PTFE and no folds or cracks will occur. Modern quality assurance methods are used which create repeatable quality over the future years. RESISTOFLEX GMBH have the TÜV-approval according to ISO 9001:0. Furthermore we offer E-certificates for all lined pipe and fittings, acc. to catogory III, module B plus 1. Many checks and production supervision are existing such as incoming goods, raw materials, semifinished products and final testing. At some departments EDP supported data are elaborated or stored. The existing catalogue with all of its principle drawings shows the offered products and data. Furthermore it is information for producers, distributors and users and to promote understanding between buyers and sellers. The nominal pipe size NPS is mainly used as criterion. Based on technical reasons these NPS correspond only approximately to the true inside diameters of the lined pipe and fittings. 1. Introduction 2.1 Product range RESISTOFLEX GMBH offers flanged pipe, fittings, chemical transfer hoses etc. as per the following range: - Nominal pipe size DN 0 to DN - Nominal pipe size NPS 1/2" to NPS 24" - particular pipe spools up to DN / NPS 24" - products acc. to DIN 2848 / 287 reduced correlation utilizat. - products acc. to ASME / ANSI B16.5 lass 1 and - other pressure classes in DIN as PN16, PN or PN - lined pipe in single length of 6 meters / feet - variable wall thickness of liners up to mm / 6 inch - high vacuum resistance of all sizes - homogeneous, seamless linings - all parts producible in electrostatically nonchargeable PTFE or PFA - working ranges from 30 / F to +260 / +4 F Please take single values from the product data sheets and the technical data. 2.2 Linings Only virgin fluorocarbon resins will be used. They meet the following specifications : - ASTM D-4894 Granular resin PTFE - ASTM D-4895 Paste / fine powder resin PTFE - ASTM D-3307 Type II PFA - DIN 2874 Flanged pipe and fittings - GKV Quality requirements The linings and dimensions meet: - DIN 2848 PTFE / PFA - ASTM F-45 PTFE / PFA The temperature rates for PTFE and PFA lined parts are between 30 / F and +260 / +4 F. Owing to the shape or reinforcement these temperature rates may be reduced on some of the products. As a rule PTFE parts are manufactured in virgin white. Black coloured paste liners are also available. PFA parts are in virgin opaque. Electrically conductive linings from PTFE are dark black. 2. Technical Data TDS-EU-DIN-A-E-04

2 3.1 Physical Values Physical values are taken from semi-finished products, tensile specimen or films, after production by RESISTOFLEX GMBH. hemical and physical resistance are acc. to ASTM - D 543. If you need more information, we will obtain this from the resin manufacturers. Property Unit Value Value PTFE- PTFE- Granulat white Paste white Value PFA Method of Inspectio n specific gravity gr / cm3 2,13 2,18 2,13 2,18 2,13 2,16 DIN tensile strength N / mm2 > > 26 > 21 DIN / SPI FD-105 e longation % > 270 > 275 > 0 DIN / SPI FD-105 tensile Modulus N / mm DIN compressive strength : 1% yield point N / mm DIN % yield point N / mm thermal conductivity coefficient of linear thermal expansion urface resistivity s 0 volume resistivity 0 flammability permeability qg permeability coeff. PG W / m x K DIN K x x ,5 x DIN cm / min x 1 4 DIN ± 1 0 2± DIN ± 1 0 2± self-extinguishin g DIN c m m 2 x 24h x bar DIN 53 3 / c thickness of sample m 3 ( 1-3) x ( 1-3) x ( 1-3) x 1 s = 2 mm m x sec x cmhg 3. General properties of virgin PTFE and PFA 3.2 Tensile-/elongation diagrams of PTFE-finepowder, s=2,4 mm, sample acc. to SPI FD-105. ε (%) 275 σ Ρ 30 N/mm 2 χα. ca. ε (%) 275 χα. ca. longitudinal τρανσϖερσαλ transversal 3.3 Administation registered application 2 σ Σ Ν /µµ N/mm 2 σ Ν /µµ 2 Σ N/mm 2 σ (N/mm (Ν/µµ 2 ) 2 ) (N/mm 2 ) σ (N/mm (Ν/µµ 2 ) 2 ) Fluoropolymer resins PTFE and PFA used by RESISTOFLEX GmbH for linings are also selected acc. to a.) production in compliance with the Federal lean Air Amendment of 1990 and are not damaging to the environment nor must carry labels and b.) are released as articles intended to contact food, as indicated below / 128 / EWG, 92 / 39 / EWG, 93 / 9 / EWG, - Bedarfsgegenständeverordnung vom , - FDA 21 FR 177. The responsibility for testing and for suitability of the products, shipped by us regarding the application or installation remains with the user. Medical applications are not allowed without permission. As far as admixtures exist in the linings, they consist of industrial manufactured amorphous carbon black or are authorized acc. to the above mentioned licences. σ Ν /µµ 2 Ρ 30 N/mm 2

3 3.4 Time yield limit of PTFE - liner between +23 and Maximum pressure ratings The chart below indicates the maximum pressure ratings for fluorcarbon plastic lined carbon steel pipe and fittings. at Temperature ( ) DIN ( bar ) DIN PN ( bar ) , 5 13, , , , , TDS-EU-DIN-B-E-04

4 4.1 Steel pipe Steel pipe are either seamless or welded. They meet the following specifications : - St 37.0 = St 35.8 = Fittings are assembled from parts acc. to : DIN 2605 / 2606, Teil 1 DIN 26, Teil 1 DIN 2616, Teil 1 for elbows for tees for reducers or welded from steel pipe. Some of the parts are also machined; for these, the materials are RSt 37-2 or H II. 4.3 Flanges Variants : - welding neck flanges acc. to DIN lapped joint short stub end and loose flanges acc. to DIN slip on welding flanges acc. to DIN 76 - collar and lapped flanges acc. to DIN 2642B The used materials are : - RSt 37-2 / H II / / Pipe, Fittings and Flanges 4.4 Screws and Nuts The quality of screws / nuts being used in the case of assembled parts that are screwed together in the plant corresponds to DIN 267. For screws applies strength class 4.6 respectively 5.6 in steel as well as A2 respectively A4 in alloy steel. For nuts applies strength class 5 in steel as well as A2 respectively A4 in alloy steel. Hexagon socket head screws DIN 912 are only available in class 8.8, 12.9 or A4. Stud bolts DIN 938 will be offered in class 5.8 or A Earthing studs allow the external earthing of the pipe system and are availabele on Value and on Select series. The studs are welded in the middle of the steel fitting or spool with a length of less than 0mm. For longer spools or fittings the stud is welded at 1 mm behind the flange. The material used for earthing studs is stainless steel. The dimensions of the suds are a M6 thread mm long. Vent extenders allow the venting system to perform through the insulation. With vent extenders it is also possible to collect the permeant. Vent extenders are available on Value and on Select Sereis. The vent extenders are welded in the middle of the steel fitting or spool with a length of less than 0mm. For longer spools or fittings the vent extender is welded at 1 mm behind the flange. The standard vent extender has a 1/8 NPS thread and a outer diameter of 19mm. It is 16mm long and the used material is St37. onductive or antistatic PTFE liner has a black carbon additive that allows for the dissipation of static electricity through the PTFE liner to the metal pipe or fitting wall. onductive liner is available in the Select Sereis only. onductive liner thickness are 6% - 8% less than for non-conductive liner. The physical values of conductive liner are approximately % lower than for non conductive liner.

5 The tolerances of the lined products observe the specification of DIN 2848 / Further details are contained in the single information sheets 5. Tolerances The marking of the products is permanent. It is made according to DIN 2848 / Special requests are possible. With the exception of some red.-flanges, blind-flanges and the solid PTFE parts, all lined pipe and fittings are provided with vent holes. These have diameters mostly from 3 to 4 mm. They serve to inspect after production as well as to indicate leaks when working. Depending on service conditions vent hole extensions with an internal thread could be welded on. This opens the possibility to either compensate for insulation, suck off permeation or to close them by screws to avoid environmental pollution. If vent hole extensions will be used, one per part is sufficient. We recommend to keep the vent holes always open. losed vent holes may cause collapsing of liners, due to permeated gas between lining and housing. 6. Marking 7. Vent Holes Metal surfaces on the outside of flanged pipe parts are subjected to steel shot blasting SA 2.5 and treated with zinc rich epoxy primer. Multilayer coatings tend to cracking while fixed at site; we do not recommend them. 8. Protective oating All assemblies have their flared gasket faces covered with end plates secured by either clips or metal bolts. This serves to protect the lining, to keep the flared face down as well as to maintain the interior clean. Parts with injected plastic (PFA) or isostatically pressed PTFE-gasket faces can be protected by plastic caps. The final inspection of the finished products occurs in several ways. First of all by visual control as to clean and good surfaces and subsequently by dimensional control of length, flange face, threads, check of marking etc. Finally a pressure and tightness test according to the shape and dimension is carried out. % of all parts are checked at room temperature as follows : - straight pipe = 14 x 10 5 Pa hydraulically or pneumatically - elbows = 14 x 10 5 Pa and 35 kv D - tees, crosses, instrument tees = 14 x 10 5 Pa and 35 kv D - chemical transfer hoses = 1,5 x nominal pressure - industrial hoses = 1,5 x working pressure - others = 35 kv D or according to agreements Pressure tests according to ASTM F-423 and F-781 (elevated pressure) are only carried by agreement. Special checks in warm water bath with outside pressure or vacuum checks under raised temperatures are possible. 9. Flange Protectors 10. Final Inspection TDS-EU-DIN--G-04

6 11.1 At the passage of media through pipe parts or flexible hoses static electric charges may form. In order to avoid these charges that may lead to spark formation and possibly to the ignition of gas-air mixtures, the PTFE-lining must allow electrical discharge. RESISTOFLEX GMBH produces upon special request lined pipe parts or fittings and flexible hoses that allow flow of static electricity Values The values refer only to PTFE powders that are adjusted to be electrically conductive. They apply both to the inside and outside surface and to the passage through the PTFE wall. As soon as the lining comes into contact with the armoured parts, i.e. pipe, hose, etc., flow of the charge through these occurs; this discharge takes place through metal parts and is therefore smaller than 10 6 Ohm. RESISTOFLEX GmbH produces PTFE linings having surface resistivities in the range between 10 4 and 10 8 Ohm. This is according to the Directions to avoid ignition danger as a result of electrostatic charges of the trade associations, committee of experts for chemistry, ZH 1/. Measuring is being carried out according to DIN and / or ASTM D7. The following definitions apply : 11. Surface resistivity on PTFE-Linings 1. Volume resistivity R A = 1 x 10 6 bis 5 x 10 8 (Ω x cm 2 ) referred to an electrode surface of diameter 22 or diameter 49,5 mm according to 5 or cm Volume resistance R D in (Ω ) that is multiplied by the electrode surface. R D = 1 x 10 6 bis 1 x 10 8 (Ω ) 3. surface resistance R O is being measured. It gives information on the insulation condition on the surface of a material. R 0 = 1 x 10 6 bis 5 x 10 8 (Ω ) 11.3 Volume and surface resistivities The Volume and surface resistivities acc. to DIN are within 10 4 and 10 6 Ohm for PTFE - granular resin and within 10 6 and 10 8 Ohm for PTFE - fine powder resin, depending on the kind of product. Electrically conductive PTFE - linings normally yield wallthicknesses which are 6 % to 8 % thinner than white ones. The physical values are also reduced to a level of approx. % below We furthermore would like to inform you, that for some liquids it might occur, that it absorbs the carbon black off the PTFE and could be contaminated.

7 Lined products must not be welded, brazed or torch-cut since this may damage the lining. For shipment all flanges are protected by covers to prevent damaging during transport and storage. These covers should only be removed shortly before installation. If dismantled for inspection they should be replaced immediately. It is not necessary to use gaskets between the PTFE sealing faces. If, however, flares are connected to sealing faces of other materials, such as glass, ceramics, carbon, or metal, and where the flares may not be parallel, it is recommended that an additional PTFE gasket be employed. This gasket should be 5 mm thick. It can absorb unevenness. Excessive bolt tightening during assembly can deform the sealing face. To avoid this, the following bolt torques should not be exceeded. See table below for allowed torques Bolt torques of the flange screws to DIN for PN 1 PN 16 and PN are shown in the table below. These torque values are valid for lightly oiled bolts according to quality 5.6 / 5 and evtl. washers. orroded threads may increase the torque values ineffective or even double them. Tighten the flange bolts with a torque wrench, using a crisscross pattern that alternately tightens the bolts located 1 apart. Using this pattern, tighten the bolts in % increments of the final bolt torque until % of the final bolt torque has been achieved. For tightening to the final torque values, tighten bolts sequently clockwise once around the flange. This will help ensure that the bolts are evenly stressed. 12. Installation and Maintenance Instructions for Lined Pipe, Fittings, Transfer Hoses and Expansion Joints Dimension DN bolts PN10 PN 16 PN bolt torque Nm bolts bolt torque Nm bolts bolt torque x M12 4 x M12 4 x M x M x M x M x M x M x M x M x M x M x M x M x M x M x M x M x M x M x M x M x M x M x M x M x M x M x M x M x M x M x M x M x M x M x M x M x M x M x M30-3 x M x M x M x M Nm TDS-EU-DIN-D-E-04

8 A retorque should be applied a minimum of 24 hours after the initial torque or after the first thermal cycle. This allows for seating of the plastic and for relaxation of the bolts. If the system is to perform at elevated temperatures, it is recommended that hot water be circulated at the maximum operating temperature of the process if possible for a minimum of 24 h. This allows for the pipe system to experience one thermal cycle. After cool-down, retorquing of the system should be done. Torquing should only be done on the system in the ambient, cooled state, never while the process is at elevated temperature or excessive force could be applied to the plastic faces. Retorque should be done annually thereafter especially if the process line experiences elevated temperatures or extreme ambient temperature situations. Frequency of retorque depends on application. Vibration, bolt strenth or number of thermocycles are important. ontinous processes need less retorque. old flow of flare material is shown under 3.3 of this specification. All lined products have small vent holes. It is important that these are not be blocked by insulation or plugged by paint as this may cause the lining to collapse. These vent holes also serve as early warning leakage indicators.the number of vent holes may be reduced if necessary. Those which remain could be provided with screwed couplings to either closed with nipples or connected to a vacuum pump. To avoid damage to the sealing faces, pipes and fittings should only be dismantled below +. If a flange connection leaks even though all bolts are tight, DO NOT TIGHTEN UP ANY MORE. Never exceed the above mentioned bolt torques. Loosen the bolts opposite the leak and tighten up the other side. If leakage persists, the sealing faces should be inspected for grooves or chips. Grooves or nicks not deeper than approx. % of the flare thickness can be removed with fine-grained abrasive paper Maximum pressure ratings This chart indicates max. pressure ratings for PTFE lined carbon steel pipe and fittings as indicated in this catalogue. PN Temp Pressure bar Pressure bar 18

9 13.1 Permeation Ratings Permeation on different kinds of fluoropolymer linings;comparison. 13. Permeation The test conditions are as follows: Material - surface of samples = cm 2 - test medium = Helium - test pressure p = 2 bar Thickness of Sample mm PFA - Film 2, 3 PTFE - Ram 4 PTFE - Granulat 4 PTFE - Paste 4 Temperatur e Time of Tes t / F h Permeation dm 3 m2 x 24h x bar / ca. 5, 3 85 / ca. 22 / ca. 3, 3 85 / ca. 30 / , 2 85 / ,4-7 / / ,5-5.2 Permeation, migration of molecules through the lining wall Diffusion is a spontaneous transport of medium caused by thermodynamic forces to compensate for concentration differences. The media migrates in the direction of decreasing concentration. Of practical importance is the permeation through finite wall thicknesses with measured values for judgement. How now does the permation of a molecule through a plastic wall happen and which are the most important parameters? A molecule inside the tube wall exerts almost elastic vibrations against it. With it energy must be supplied to overcome the linkage forces in the plastic or to move through socalled free spaces (no voids). PTFE is a hypocrystalline substance and the so-called free spaces are to be found in the amorphous part. rystalline zones are not penetrated. A series of influences causes individually or together the permeated quantity. It is presumed that both from liquid media and from gases only the gases permeate. The moving forces with it are the concentration or the partial pressure. In the case of substance mixtures both single components and their interactives may migrate. Little molecules get easier through so-called free spaces than big ones. hain molecules as well permeate easier than branched ones, since their cross-sectional area is smaller. A temperature increase supplies energy; this increases vibrations in the wall and in the media. Thus the activity of the molecules increases, the wall expands and possibly the amorphous part of the wall PTFE increases and as a result more molecules move quicker through. We get into a limit area when a media has a similar or equal polarity as the lining. Then the liquid may partially dissolve in the wall; it is then spoken of a swelling. With it the space between the macromolecules of the wall increases, that is more and greater free spaces develop. All molecules move then quicker through the wall even if only one generates the swelling. The thicker the lining is, the smaller is the permeation. High crystallinity reduces permeation. Greatest caution is anyhow advisable here, since as manufacturers we always aspire to an optimum between permeation and durability with regards to crackings in the PTFE; high crystallinity reduces flexibility and increases drastically the risk of fracture. FLUOROFLEX products always guarantee durability, low permeation values and operational reliability. TDS-EU-DIN-E-E-04

10 In general PTFE is chemically inert. We therefore differentiate between chemical reaction and physical behaviour. That is why in the following we deal with the physical interaction between plastic and contacting media. Submicroscopic little spaces between the polymer molecules make it for some substances, as e. g. water vapor, monomeres etc., possible to diffuse into the PTFE. By this the spontaneous media transport caused by pressure and temperature is meant. The medium moves in the direction of decreasing concentration. Absorption means here that a liquid diffuses into the PTFE and that the quantity increases with increasing pressure and increasing temperature. If a lined tubing part is subjected to cyclic pressure and temperature loads, so that the liquid entrapped in the plastic wall evaporates or condenses, then the resistance of the plastic may be reduced at several points. This originates bubbles that in the course of time develop into so-called blisters. The PTFE there suffers a locally limited delamination. FLUOROFLEX-PTFE linings are brought into an optimal condition. Only raw material having on one hand a sufficient flexibility and on the other a relatively high share in crystalline PTFE are being used. The situation is additionally aggravated by the great operative temperature range of PTFE and the thermal fluctuation originating with it between operation and standstill. It is presumed that owing to the pressure drop vapour penetrates in the PTFE, and since there prevails a great temperature drop the vapour condenses in the wall. During cyclic operation, that is stop and restart, the entrapped condensation quantities are being expanded with rising temperature, their volume increases and the plastic is being locally laminated. Depending on this condition the formation of bubbles or blistering proceeds. This anyhow leads not at all or only after a comparatively long time to the total failure or outage of parts, since blisters mostly lie in the inner third of the wall, that is maintained in its function as separation layer. How can we reduce this phenomenon? Since mostly the process condition cannot be changed, an insulation of the tubing parts usually clearly improves the situation or even avoids these blisters completely, the insulation of the flange area or other metal suspensions being there particularly important. The insulation avoids the great temperature drop and thus the condensation that is later expansion. A qualifying test for PTFE is therefore also the so-called vapour-cold water test according to ASTM F-423. Papers treating this subject are: - Du Pont, reprint of the Journal of Teflon Nr. 1-D-2; A Du Pont, Teflon/Tefzel, protection against corrosion in chemistry H ASTM F NBS Voluntary Product Standard PS des US Department of ommerce All data shown in this catalogue according to our best knowledge but does not constitute any form of guarantee. Recommendations for use are only advisory. They do not release the user from his obligation to prior check the delivered products concerning their safety and readiness for use. 14. PTFE Absorption Behaviour in hemical Aplication. General Information

11 16. Pressure Dimensions - compared between atmosph. Pressures and full Vacuum PA MPa 2 1 Pa = 1 N/m 1 0 bar mbar m WS mm WS mm Hg psi 2 kp / cm 2 2 N / m MN / m ( Torr ) ( at ) ,02 x ,02 x ,5 x ,45 x ,02 x MPa = 1 MN/m ,02 x bar ,02 x ,02 1 mbar mws 9,81 x 10,81 x 10 1 mmws 9,81,81 x mmhg ( Torr ) 1,33 x 10,33 x psi 6,89 x 10,89 x kp/cm 9,81 x 10,81 x kp/cm = 9,6 N/cm = 096 N/mm 2 1 kp = 9,6 kg x m/sec = 9,6 N - 1,02 x ,81 x 1 0-2,81 x ,81 x 10-9,81 x ,33 x 1 0-3, ,89 x 1 0-2,89 x ,81 x 1 0-1,81 x ,5 x ,45 x ,02 x ,36 x 10 1,42 0-1,36 x ,03 x 10-1,5 x ,36 x ,03 x ,42 x ,93 x ,36 x ,17 x 10 1,03 x ,36 x 10 1,42 x 10 1 TDS-EU-DIN-F-E-04

12

13 PTFE Lined Pipe Spool DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN Value F x L Select F x L Same construction as select series but only in fix length available: - 0 mm - 0 mm - 10 mm - 0 mm - 0 mm below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Fix or Loose Flanges Stainless Steel Housing onductive Liner Heavy Duty Liner Special Paint Earthing Studs Vent Extenders Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-PFT-E-4

14 PTFE Lined Pipe Spool Fabricated Steel Dimensional Data per DN Min L Max L S+ 10% Pipe Weight (ca. kg/m) 2 Flanges Weight (ca. kg) , 5 1, 2 1, , , 5 2, 5 2, , 4 3, , 8 5, , 1 6, , , , 5 13, , , , , , Note: - DN, DN and DN not acc. to DIN 2848 Part Number System 1 ROF 0 10 W XX FF 00XX Type Finished Fitting Pipe Spool Diameter Pressure PN Liner W - White E - Anti-Static Resin Type Factory Defined Flanges FF - Fixed/Fixed FL - Fixed/Loose LL - Loose/Loose 00XX - Standard Earthing Stud Vent Boss Stainless Steel

15 PTFE Lined 90 Degree Elbow DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN Value F x F Select F x L Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Fix or Loose Flanges Special Angle Stainless Steel Housing onductive Liner Heavy Duty Liner Special Paint Earthing Studs Vent Extenders Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-L9T-E-04

16 PTFE Lined 90 Degree Elbow Fabricated Steel Dimensional Data per S ize L S+ 10% Note: DN 3 piece housing DN, and not acc to DIN 2848 Part Number System 1 B W XX FF 00XX Type Finished Fitting 90 Deg. Elbow Diameter Pressure PN Weight (ca. kg) , , 5 2, ,75 2, , , , , , 13, , 5 18, , , , , Liner W - White E - Anti-Static Resin Type Factory Defined Flanges FF - Fixed/Fixed FL - Fixed/Loose LL - Loose/Loose 00XX - Standard Earthing Stud Vent Boss Stainless Steel

17 PTFE Lined 45 Degree Elbow DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN Value F x F Select F x L Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Loose or Fix Flanges Special Angle Stainless Steel Housing onductive Liner Heavy Duty Liner Special Paint Earthing Studs Vent Extenders Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-L5T-E-04

18 PTFE Lined 45 Degree Elbow Fabricated Steel Dimensional Data per Size Part Number System 1 B W XX FF 00XX Type Finished Fitting L 45 Deg. Elbow Diameter S+ 10% Pressure PN Weight (ca. kg) , 0 1, , 5 2, , 7 2, , , , , , 3 13, , 5 18, , , , , Note: DN, and not acc. to DIN 2848 Liner W - White E - Anti-Static Resin Type Factory Defined Flanges FF - Fixed/Fixed FL - Fixed/Loose LL - Loose/Loose 00XX - Standard Earthing Stud Vent Boss Stainless Steel

19 PTFE Lined Equal Tee DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN Value F x F x F Select F x L x L below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Loose Flanges on Select Ser. Stainless Steel Housing onductive Liner Heavy Duty Liner Special Paint Earthing Studs Vent Extenders PFA lined 2-pc. construction Standard Standard Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-TET-E-04

20 PTFE Lined Equal Tee Fabricated Steel Dimensional Data per D N L Note: - DN 4 and not acc. to DIN DN 0 face to face dimensiones not acc. to DIN 2848 Part Number System 1 TEE 0 10 W XX FF 00XX Type Finished Fitting Equal Tee Diameter S+ 10% Pressure PN Weight (ca. kg) , , , 5 5, , , , , , , , , Liner W - White E - Anti-Static Resin Type Factory Defined Flanges FF - 3 x Fixed B - 1 x Fixed 2 x Loose LL - 3 x Loose 00XX - Standard Earthing Stud Vent Boss Stainless Steel

21 PTFE Lined Reducing Tee DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN - 1 DN 1 1 DN 2 Value F x F x F Select F x F x F below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Loose Flanges Stainless Steel Housing onductive Liner Heavy Duty Liner Standard St. Special Paint Earthing Studs Vent Extenders Standard PFA-Lined St. Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated Form No. TDS-EU-DIN-TRT-01-E-04

22 PTFE Lined Reducing Tee Fabricated Steel DN - 1 Dimensional Data per DN 1 DN 2 Part Number System 1 RTE 0 10 W XX FF 00XX Type Finished Fitting Red. Tee L1 Diameter L2 1 Pressure PN 2 S % S % Liner W - White E - Anti-Static Resin Type Factory Defined Weight (ca. kg) , , , , , , , , , ,5 28, , 4 Note: - other dimensiones on request Factory Defined Flanges FF - 3 x Fixed B - 1 x Fixed 2 x Loose LL - 3 x Loose 00XX - Standard Earthing Stud Vent Boss Stainless Steel

23 PTFE Lined Reducing Tee DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN - DN 1 DN 2 Value Value not Available in these Sizes Select F x F x F below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Loose Flanges Stainless Steel Housing onductive Liner Heavy Duty Liner Special Paint Earthing Studs Vent Extenders 0 1 Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated Form No. TDS-EU-DIN-TRT--E-04

24 PTFE Lined Reducing Tee Fabricated Steel DN - Dimensional Data per DN 1 DN 2 0 L1 L2 1 2 S % S % Weight (ca. kg) Note: - other dimensiones on request Part Number System 1 RTE 0 10 W XX FF 00XX Type Finished Fitting Red. Tee Diameter Factory Defined Pressure PN Liner W - White E - Anti-Static Resin Type Factory Defined Flanges FF - 3 x Fixed B - 1 x Fixed 2 x Loose LL - 3 x Loose 00XX - Standard Earthing Stud Vent Boss Stainless Steel

25 PTFE Lined Reducing Tee Flange DIN 01; dim. L1 acc to DIN 2848 E, PED at. III (>0) TEFLON by DuPont DN 3 - DN DN 2 Value Value not Available in These Sizes Select F x F x F below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Loose Flanges Stainless Steel Housing onductive Liner Heavy Duty Liner Special Paint Earthing Studs Vent Extenders Standard 2-pc Body onstruction Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated Form No. TDS-EU-DIN-TRT-3-E-04

26 PTFE Lined Reducing Tee Fabricated Steel DN 3 - Dimensional Data per DN 1 DN L1 L2 1 2 S % S % Weight (ca. kg) ,5 8 3, , , , , , , , Part Number System 1 RTE 0 10 W XX FF 00XX Type Finished Fitting Red. Tee Diameter Pressure PN Liner W - White E - Anti-Static Resin Type Factory Defined Flanges FF - 3 x Fixed B - 1 x Fixed 2 x Loose LL - 3 x Loose Note: - other sizes on request 00XX - Standard Earthing Stud Vent Boss Stainless Steel

27 PTFE Lined Equal ross DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN Value Equal crosses not avaliable in Value Select F x F x F x F below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Loose Flanges on Select Ser. Stainless Steel Housing Heavy Duty Liner onductive Liner Special Paint Earthing Studs Vent Extenders PFA lined 3 pc. body construction Standard Standard Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-ET-E-04

28 PTFE Lined Equal ross Fabricated Steel Dimensional Data per D N L Part Number System 1 KRE 0 10 W XX FF 00XX Type Finished Fitting Equal ross S+ 10% Diameter Pressure PN Weight (ca. kg) , , , 5 7, , 7 1 5, , , , , , 3 3 6, , , , Note: - DN 4 and not acc. to DIN DN 0 face to face not acc to DIN 2848 Liner W - White E - Anti-Static Resin Type Factory Defined Flanges FF - 4 x Fixed XX - 1 x Fixed 3 x Loose LL - 4 x Loose 00XX - Standard Earthing Stud Vent Boss Stainless Steel

29 PTFE Lined Reducing ross DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN - DN 1 DN 2 Value not available in Value Select F x F x F x F Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Loose Flanges Stainless Steel Housing onductive Liner Heavy Duty Liner Standard Special Paint Earthing Studs Vent Extenders Standard PFA-Lined Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated Form No. TDS-EU-DIN-RT-0-E-04

30 PTFE Lined Reducing ross Fabricated Steel DN - Dimensional Data per DN 1 DN 2 Note: - other dimensiones on request Part Number System 1 RKR 0 10 W XX FF 00XX Type Finished Fitting Red. ross L1 Diameter Factory Defined L2 1 Pressure PN 2 S % S % Liner W - White E - Anti-Static Resin Type Factory Defined Weight (ca. kg) , 5 3 3, , , 5 5, , 0 8, , , , , , , 0 32 Flanges FF - 4 x Fixed XX - 1 x Fixed 3 x Loose LL - 4 x Loose 00XX - Standard Earthing Stud Vent Boss Stainless Steel

31 PTFE Lined Reducing ross Flange DIN 01; dim. L1 acc to DIN 2848 E, PED at. III (>0) TEFLON by DuPont DN 1 - DN DN Value not available in Value Select F x F x F x F Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Loose Flanges Stainless Steel Housing onductive Liner Heavy Duty Liner Special Paint Earthing Studs Vent Extenders Standard 3-pc Body onstruction Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated Form No. TDS-EU-DIN-RT-1-E-04

32 PTFE Lined Reducing ross Fabricated Steel DN 1 - Dimensional Data per DN 1 DN 2 Note: - other sizes on request Part Number System 1 RKR 0 10 W XX FF 00XX Type Finished Fitting Red. ross L Diameter L2 1 Pressure PN 2 S % S % Liner W - White E - Anti-Static Resin Type Factory Defined Weight (ca. kg) , , 0 5, , , , ,5 6, , , ,5 6, ,5 6, ,5 6, , Flanges FF - 4 x Fixed XX - 1 x Fixed 3 x Loose LL - 4 x Loose 00XX - Standard Earthing Stud Vent Boss Stainless Steel

33 PFA Lined Instrument Tee DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN - DN 1 DN 2 Value Select below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Stainless Steel Housing onductive Liner Heavy Duty Liner Special Paint Earthing Studs Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-TIT-00-E-04

34 PFA Lined Instrument Tee Fabricated Steel DN - Dimensional Data per Major size Part Number System 1 MST 0 10 W XX 00 00XX Type Finished Minor Size Fitting Instr. Tee L Diameter H onsult Factory 1 Pressure PN 2 S+ 10% Liner W - White E - Anti-Static Weight (ca. kg) 43 1, , , , ,2 60 3, , , , , 6 Resin Type Factory Defined Flanges 00 00XX - Standard Earthing Stud Vent Boss Stainless Steel

35 PFA Lined Instrument Tee DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN - 0 DN 1 DN 2 Value Select below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Stainless Steel Housing onductive Liner Heavy Duty Liner Special Paint Earthing Studs 1 0 Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-TIT-0-E-04

36 PFA Lined Instrument Tee Fabricated Steel DN - 0 Dimensional Data per DN 1 DN Part Number System 1 MST 0 10 W XX 00 00XX Type Finished Fitting Instr. Tee L Diameter H onsult Factory 1 Pressure PN 2 S+ 10% Liner W - White E - Anti-Static Weight (ca. kg) 43 5,5 60 5, , , , , , , , , 9 Resin Type Factory Defined Flanges 00 00XX - Standard Earthing Stud Vent Boss Stainless Steel

37 PTFE Lined Instrument Tee flanges acc. to DIN 01, E, PED at. III (>0) TEFLON by DuPont DN - DN 1 DN 2 Value Value Not Available in These Sizes Select below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Stainless Steel Housing onductive Liner Heavy Duty Liner Special Paint Earthing Studs Vent Extenders 2-Pc Body onstruction Standard Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-TIT--E-04

38 PTFE Lined Instrument Tee Fabricated Steel DN - Dimensional Data per DN 1 DN Part Number System 1 MST 0 10 W XX 00 00XX Type Finished Fitting Instr. Tee L 90 Diameter H onsult Factory 1 Pressure PN 2 S+ 10% Liner W - White E - Anti-Static Weight (ca. kg) ,5 / 3 55, , ,5 / 3 66, ,1 1 73, ,5 / ,1 1 83, ,5 / 3 9 5,5 1 93, ,5 / ,1 1, / , , 7 Resin Type Factory Defined Flanges 00 00XX - Standard Earthing Stud Vent Boss Stainless Steel

39 PTFE Lined Equal Lateral Tee E, PED at. III (>0) TEFLON by DuPont DN Value not available in Value Select F x F x F below not available on stock items.option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Loose Flanges on Select Ser. Stainless Steel Housing onductive Liner Special Paint Earthing Studs Vent Extenders Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated Form No. TDS-EUR-DIN-LET-E-04

40 PTFE Lined Equal Lateral Tee Fabricated Steel Dimensional Data per DN L L1 L2 S+ 10% Weight (ca. kg) , 5 5, , , , , , 9 Part Number System 1 LTE 10 W XX FF 00XX Type Finished Fitting Lateral Tee Diameter Pressure PN Liner W - White E - Anti-Static Resin Type Factory Defined Flanges FF - 3 x Fixed B - 1 x Fixed 2 x Loose LL - 3 x Loose 00XX - Standard Earthing Stud Vent Boss Stainless Steel

41 PTFE Lined Reducing Flange DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN - 1 DN 1 DN 2 Value Select below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Stainless Steel Housing Eccentric onductive Liner Heavy Duty Liner Special Paint Earthing Studs 1 Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated Form No. TDS-EU-DIN-RFT-01-E-04

42 PTFE Lined Reducing Flange Fabricated Steel DN - 1 Dimensional Data per Major Size 1 Part Number System 1 RFK 0 10 W XX 00 00XX Type Minor Size Fitting Finished Reducing Flange L Diameter 1 2 Pressure PN S+ 10% Liner Type W - White E - Anti-Static Weight (ca. kg) 45 3, 0 2, , 5 2, ,0 B , 1 0 / 3, 5 A 6, ,6 0 B 6, 4 5 / 3, 5 A B 5 / ,0 / 0 A ,0 / 5 B 17 All major size bolt holes straddle the natural centerline. A - Minor size bolt holes straddle the natural centerline. B - Minor size bolt holes straddle the centerline; Major size bolt holes with thread - Minor size bolt holes are on the natural centerline; Major size bolt holes with thread other dimensiones on request Factory Defined Resin Type Factory Defined Flanges 00 00XX - Standard Earthing Stud Stainless Steel

43 PTFE Lined Reducing Flange DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN - 3 DN 1 DN 2 Value Value not available in this sizes Select below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Stainless Steel Housing Eccentric onductive Liner Heavy Duty Liner Special Paint Earthing Studs Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated Form No. TDS-EU-DIN-RFT-3-E-04

44 PTFE Lined Reducing Flange Fabricated Steel DN - 3 Dimensional Data per Major size 0 3 All major size bolt holes straddle the natural centerline. A - Minor size bolt holes straddle the natural centerline. B - Minor size bolt holes straddle the centerline; Major size bolt holes with thread - Minor size bolt holes are on the natural centerline; Major size bolt holes with thread Note: - DN 0 and up have cylindrical openings - other sizes on request Part Number System 1 RFK 0 10 W XX 00 00XX Type Minor Size Fitting Finished Reducing Flange L Diameter 1 2 Pressure PN S+ 10% Liner Type W - White E - Anti-Static Weight (ca. kg) 28 5,0 / A ,0 / , 0 B ,0 / 0 8 A ,0 2 B ,0 / A ,0 / , ,0 / 0 A 2 38 Factory Defined Resin Type Factory Defined Flanges 00 Red. Flange 00XX - Standard Earthing Stud Stainless Steel

45 PTFE Lined Reducing Flange DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN 0 - DN 1 DN 2 Value Value not available in these sizes Select below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Stainless Steel Housing Eccentric onductive Liner Heavy Duty Liner Special Paint Earthing Studs Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated Form No. TDS-EU-DIN-RFT-0-E-04

46 PTFE Lined Reducing Flange Fabricated Steel DN 0 - Dimensional Data per Major size Part Number System 1 RFK 0 10 W XX 00 00XX Type Minor Size Fitting Finished Reducing Flange L Diameter 1 2 Pressure PN S+ 10% Liner Type W - White E - Anti-Static Weight (ca. kg) 8 6,0 / A , ,0 / 0 A ,0 / 0 A ,0 / 0 A All major size bolt holes straddle the natural centerline. A - Minor size bolt holes straddle the natural centerline. B - Minor size bolt holes straddle the centerline; Major size bolt holes with thread - Minor size bolt holes are on the natural centerline; Major size bolt holes with thread Note: - DN 0 and up have cylindrical openings - DN not acc. to DIN other sizes on request Factory Defined Resin Type Factory Defined Flanges 00 00XX - Standard Earthing Stud Stainless Steel

47 PTFE Lined oncentric Reducer DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN - 1 Major Size Minor Size Value F x F Select F x F below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Loose Flanges on Select Ser. Stainless Steel Housing onductive Liner Heavy Duty Liner Special Paint Earthing Studs Vent Extenders 1 Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-RT-01-E-04

48 PTFE Lined oncentric Reducer Fabricated Steel DN - 1 Dimensional Data per Major size Part Number System 1 RSK 0 10 W XX FF 00XX Type Finished Minor Size Fitting onc. Reducer L Diameter Pressure PN S+ 10% Liner W - White E - Anti-Static Weight (ca. kg) 45 2,4 1 3,0 58 2, , 0 3, / 3, ,7 0 / 3, , , / 3, , 4 8 9,9 5 / , ,0 / , ,0 / 5 18, 3 Note: - other sizes on request Factory Defined Resin Type Factory Defined Flanges FF - Fixed/Fixed FL - Fixed/Loose LL - Loose/Loose 00XX - Standard Earthing Stud Vent Boss Stainless Steel

49 PTFE Lined oncentric Reducer DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN - Major Size Minor Size Value Value not available in this sizes Select F x F below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Loose Flanges Stainless Steel Housing onductive Liner Heavy Duty Liner Special Paint Earthing Studs Vent Extenders Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-RT--E-04

50 PTFE Lined oncentric Reducer Fabricated Steel DN - Dimensional Data per DN 1 DN Part Number System 1 RSK 0 10 W XX FF 00XX Type Finished Fitting onc. Reducer L1 Diameter 1 Pressure PN 2 S+ 10% Liner W - White E - Anti-Static Weight (ca. kg) 2 8 6,0 / 5 22, ,0 / 5, 0, ,5 / 5, 0 37, ,5 / 6, , , ,6 4 6, , , , Note: - DN 4 and not acc. to DIN other sizes on request Factory Defined Resin Type Factory Defined Flanges FF - Fixed/Fixed FL - Fixed/Loose LL - Loose/Loose 00XX - Standard Earthing Stud Vent Boss Stainless Steel

51 PTFE Lined Eccentric Reducer DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont Major Size Minor Size Value eccentric reducers not available in value series Select F x F below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Loose Flanges on Select Ser. Stainless Steel Housing onductive Liner Heavy Duty Liner Special Paint Earthing Studs Vent Extenders Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-RET-032-E-04

52 PTFE Lined Eccentric Reducer Fabricated Steel Dimensional Data per DN 1 D N 2 L Part Number System 1 RSE 0 10 W XX FF 00XX Type Finished Fitting Ecc. Reducer Diameter Pressure PN S+ 10% Liner W - White E - Anti-Static Weight (ca. kg) / 3, 0 3, ,0 / 0 6, , , ,5 / 5 9, / 3 9, / 0 12, / 6 17, / 5 18, / 5 22, / 5, ,5 / ,5 / , 5 48 Factory Defined Resin Type Factory Defined Flanges FF - Fixed/Fixed FL - Fixed/Loose LL - Loose/Loose 00XX - Standard Earthing Stud Vent Boss Stainless Steel

53 PTFE Solid Spacer DIN 2848 TEFLON by DuPont DN Value Select Option PN Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated Form No. DS-EUR-DIN-SFT-E-04

54 PTFE Solid Spacer Dimensional Data per DN Part Number System 1 DSF 0 10 W XX 00 00XX Type Finished L max Fitting PTFE Solid Spacer d Diameter d Weight (ca. kg) , , , , , , , 5 Note: - DN, DN and DN not acc. to DIN 2848 Pressure PN Liner W - White Resin Type Factory Defined Flanges 00 - Spacer 00XX - Standard

55 PTFE Solid Spacer With Support Ring TEFLON by DuPont DN Value Select Option PN Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated Form No. DS-EUR-DIN-SXT-E-04

56 PTFE Solid Spacer With Support Ring Dimensional Data per DN Part Number System 1 DSX 0 10 W XX 00 00XX Type Finished L max Fitting PTFE Solid Spacer With Support Ring d Diameter d s Pressure PN Weight (ca. kg) , , , , 1 2, , 9 2, , 6 2, , , 7 3, , , 5 3 1, , 6 3, , , , , 5 Liner W - White Resin Type Factory Defined Flanges 00 - Spacer 00XX - Standard Earthing Stud Stainless Steel

57 PTFE Lined Ring Spacer DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN Value Select below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Stainless Steel Housing onductive Liner Heavy Duty Liner Special Paint Earthing Studs Vent Extenders Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated Form No. TDS-EU-DIN-SGT-E-04

58 PTFE Lined Ring Spacer Fabricated Steel Dimensional Data per DN L min L max S+ 10% d8 Weight (ca. kg/m) 85 2, , , , , , , , , , , , , Note: - DN, DN and DN not acc. to DIN 2848 Part Number System 1 DSG 0 10 W XX 00 00XX Type Finished Fitting Lined Ring Spacer Diameter Pressure PN Liner W - White E - Anti-Static Resin Type Factory Defined Flanges 00 - Spacer 00XX - Standard Earthing Stud Vent Boss Stainless Steel

59 PTFE Lined Distance Piece Form H DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN Value Lined Distance Pieces Not Available in Value Select below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Stainless Steel Housing onductive Liner Heavy Duty Liner Special Paint Earthing Studs Vent Extenders Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated Form No. TDS-EU-DIN-SHT-E-04

60 PTFE Lined Distance Piece Form H Fabricated Steel Dimensional Data per DN Part Number System 1 DSH 0 10 W XX 00 00XX Type Finished L min Fitting Distance Piece Form H L max Diameter S+ 10% Pressure PN d8 Weight Pipe (ca. kg/m) Liner W - White E - Anti-Static Weight 2 ollars (ca. kg) 90 2, , , , , , 8 1, , 1 1, , , , , , , , , , , , Note: - DN, DN and DN not acc. to DIN 2848 Resin Type Factory Defined Flanges 00 - Spacer 00XX - Standard Earthing Stud Vent Boss Stainless Steel

61 PTFE Lined Spectacle Blind Flange DIN 2848 / 2874 E, at. III (>0) TEFLON by DuPont Value Select below not available on stock items. Option selection may affect manufacturing lead time. onsult factory for price and delivery. DN PN Stainless Steel Housing onductive Liner Heavy Duty Liner Special Paint Earthing Studs Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated Form No. DS-EUR-ANSI-E90

62 PTFE Lined Spectacle Blind Flange Fabricated Steel Dimensional Data per Size L S+ 10% k d2 d4 Weight (ca. kg) 18 2, , , , , , , , , Notes: 1.) Drawing shows typical Value construction Part Number System 1 BRL 0 10 W XX 00 00XX Type Fitting Diameter Pressure Liner Resin Type Flanges Finished Spectacle Blind Flange PN W - White E - Anti-Static Factory Defined 00 00XX - Standard Earthing Stud Vent Boss Stainless Steel Form No. DS-EUR-ANSI-E90

63 PTFE Lined Blind Flange DIN 2848 / 2874 E, PED at. III (>0) TEFLON by DuPont DN Value Select Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Stainless Steel Housing onductive Liner Heavy Duty Liner Special Paint Earthing Studs Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-FBT-G-04

64 PTFE Lined Blind Flange Fabricated Steel Dimensional Data per Size Part Number System 1 BFL 0 10 W XX 00 00XX Type Finished L Fitting Blind Flange S+ 10% Diameter Weight (ca. kg) , , , , 5 3, , 5 5 9, , Note: DN,, 4 and are not acc. to DIN Pressure PN Liner W - White E - Anti-Static Resin Type Factory Defined Flanges 00 00XX - Standard Earthing Stud Vent Boss Stainless Steel

65 PTFE Nozzle Liner TEFLON by DuPont DN Value Nozzle Liner Not Available in Value S elect Opt. onductive Liner Best Price & Lead Time (1-2 Weeks) Longer Lead Time (4-6 Weeks) Price and Delivery Upon Request TDS-EU-DIN-NLT-E-04

66 PTFE Nozzle Liner Dimensional Data DN Part Number System 1 NOZ 0 10 W XX 00 00XX Type Finished d Fitting PTFE Nozzle Liner T ol d + Diameter Pressure Liner Resin Type Flanges S+ 10% d 4+ 10% Weight (ca. kg/m) 21 1, 5 2, , , , , , , , , , , , , , , , , , , , 5 5 9, ,45 Note: - Max. length is 1,5m. Longer length on request 10 - DIN W - White Factory Defined 00 - Liner 00XX - Standard

67 PTFE Lined Dip Pipe E, PED at. III (>0) TEFLON by DuPont DN Value Select Option selection may affect manufacturing lead time. onsult factory for price and delivery. PN Stainless Steel Housing Use in Vessels with Agitators onductive Liner PTFE Solid Nozzle Special Paint Vacuum Resistance Earthing Studs 32 1 Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated Form No. TDS-EUR-DIN-DPT-E-04

68 PTFE Lined Dip Pipe Fabricated Steel Dimensional Data per DN 1 Part Number System 1 TAN 10 W XX 00 00XX Typ Finished Outside Dia. x Wall Type Fitting Dip Pipe Diameter L1 + mm Factory Defined L2 + 5 mm Pressure PN d3 d4 Liner W - White E - Anti-Static S+ 10% PTFE Type Factory Defined Weight of Pipe (kg/m) 33,7 x 2, 6 I , 7 2, ,4 x 2, 6 I , 3 3, ,3 x 3,2 I , 5 48,3 x 5,6 I 3, I , 7 7, 3 63 x 5 I x 8,0 I 3,3 7, 9 I , 3 12, 2 76,1 x 0 I , , 1 9, ,9 x 5 I ,4 12, 2 88,9 x 10 I , 4 22, 3 88,9 x 12 I I , x 5,0 I , x 10 I , x 16,0 I I , 6 1,3 x 6,3 I , ,3 x 8,0 I 5, I , , 0 36, 9 219,1 x 6, 3 I , 3 41, 2 Flanges 00 00XX - Standard Earthing Stud Stainless Steel

69 PTFE Lined Sparger E, PED at. III (>0) TEFLON by DuPont DN Value Select Option selection may affect manufacturing lead time. onsult factory for price and delivery PN Stainless Steel Housing Use in Vessels with Agitators onductive Liner Special Paint Vacuum Resistance Earthing Studs 32 1 Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated Form No. TDS-EUR-DIN-SPT-E-04

70 PTFE Lined Sparger Fabricated Steel Dimensional Data per DN Part Number System 1 ELR 10 W XX FN1 0XX Typ Finished Outside Dia. L x Wall Type + mm Fitting PTFE lined Sparger Diameter d3 Pressure PN d4 Liner W - White E - Anti-Static S+ 10% Weight Weight of Pipe of Flange (kg/m) (kg) 33,7 x 2, 6 I , 7 2, 9 1, ,4 x 2, 6 I , 3 3, 6 1, 7 48,3 x 3,2 I , 5 48,3 x 5,6 I 3,2 4 1, 9 88 I , 7 7, 3 1, 9 63 x 5 I x 8,0 I 3,3 7, 9 2, 5 I , 3 12, 2 2, 5 76,1 x 0 I , , 1 9, 2 3, ,9 x 5 I ,4 12, 2 3, 8 88,9 x 10 I , 4 22, 3 3, 8 88,9 x 12 I I , , x 5,0 I , x 10 I , x 16,0 I I , 6 1 1,3 x 6,3 I 0 177, ,3 x 8,0 I 5,0 31, 1 6, I 0 177, , 0 37, 2 6, 6 219,1 x 6, 3 I , 3 41, 2 9, PTFE Type Factory Defined Flanges FN1 = Type 1 FN2 = Type 2 FN3 = Type 3 00XX - Standard Earthing Stud Stainless Steel

71 PTFE Diaphragm TEFLON by DuPont max. Outside Diameter Number of onvolutes Value not available in Value S elect Opt. White Liner Black Liner Standard Best Price & Lead Time (1-2 Weeks) Longer Lead Time (4-6 Weeks) Price and Delivery Upon Request TDS-EU-DIN-DIT-E-04

72 PTFE Diaphragm Dimensional data max. Outside Dia. +0% / -3% Part Number System 1 MEM W Typ Finished Fitting PTFE Diaphragm Number of onvolutes max. Outside Diameter d1 + 5% Number of onv d2 + 5% Liner W - White S - Black S + 10% , , , , , , , , , , , , , , , , , , , , , , Standard

73 Pressure-temperature-diagramm for 2 convolutions Pressure-temperaturediagramms for PTFE-bellows with standard wall thickness Bellow with 2 convolutions Pressure-temperature-diagramm for 3 convolutions Pressure-temperature-diagramm for 5 convolutions Bellow with 3 convolutions Bellow with 5 convolutions TDS-EU-DIN-G-E-04

74 Pressure-temperature-diagramm for SHD-bellow with 2 convolutions for non-shock working Pressure-temperaturediagramms for PTFE-bellows with SHD wall thickness Bellow with 2 convolutions Pressure-temperature-diagramm for SHD-bellow with 3 convolutions for non-shock working Pressure-temperaturediagramm for SHD-bellow with 5 convolutions, for non-shock working Bellow with 3 convolutions Bellow with 5 convolutions

75 DN axial travel max. (+ mm) misalignment max. eff. bellows crosssection ( cm 2 ) vacuum resistance at 10 4 Pa at max. inherent resistance compress. (N / mm) W extension (N / mm) PTFE-Expansion-Joint 2 onvolutions ,4 1,5 45 6, Angular deflection approx. 7 max. Axial travel is based on installation without misalignment or angular deflection. The burst pressure is approx. 4 times the max. working pressure shown on the diagramm. The figures stated are average values and apply to room temperature. Deviations due to processing variations are possible. For compression : ompression force F c = x S 1/2 where from table S = travel in mm For extension: Expansion force F w = W x S where W from table S = travel in mm 1,5 45 6,7 1,5 45 6,7 3, , Flanges up to DN 0 have 2 limit bolts, DN 0 and have 3. TDS-EU-DIN-H-E-04

76 DN axial travel max. (+ mm) misalignment max. eff. bellows crosssection ( cm 2 ) vacuum resistance at 10 4 Pa at max. inherent resistance compress. (N / mm) W extension (N / mm) PTFE-Expansion-Joint 3 onvolutes ,4 1,5 45 6, ,5 45 6,7 1,5 45 6,7 3, , 7 Angular deflection approx. 14 max. Axial travel is based on installation without misalignment or angular deflection. The burst pressure is approx. 4 times the max. working pressure shown on the diagramm. The figures stated are average values and apply to room temperature. Deviations due to processing variations are possible. For compression : ompression force F c = x S 1/2 where from table S = travel in mm For extension: Expansion force F w = W x S where W from table S = travel in mm Flanges up to DN 0 have 2 limit bolts, DN 0 and have 3.

77 DN axial travel max. (+ mm) misalignment max. eff. bellows crosssection ( cm 2 ) inherent resistance compress. (N / mm) W extension (N / mm) PTFE-Expansion-Joint 5 onvolutes alculation of the forces for: ompression of the bellow: force Fc = x S 1/2 with from table S = travel in mm. Extension of the bellow: force Fw = W x S with W from table S = travel in mm. Please notice: - urves and chart are only valid at neutral length and with limit bolts in place. - The max. angular deflection is approx.. - Above mentioned travel, misalignment or angular deflectio are alternatives, i.e. the percentage values are not allowed to exceed % when added together. - Burst pressure is minimum 4x the indicated in the chart. ompared with the pressure curves of the 2- and 3-convolute bellows, it is here much lower because of the risk of buckling. - The figures stated are average values and apply to room temperature. Deviations due to processing variations are possible. - For abrasive applications the bellows (on request) can be equipped with a PTFEnozzle liner, flared on one side. Movements are then restricted. Savety instructions: - Follow install. instructions. - Do not exceed pressure / temperature rating shown in the appropriate bellows chart. - Safeguard the units in hazardous service. - Leave limit bolts in. Severe damage can result if they are removed or altered. - Remove the flange covers only when ready to install the bellow - Insure that sealing faces are clean, smooth and parallel. - While installing the flanges, make sure the bolts do not jut out from the flange backside to the bellow. - Improperly installation or beyond the pressure / temperature rating may result in property damage or personal injury. TDS-EU-DIN-I-E-04

78 DN axial travel max. (+ mm) misalignment max. eff. bellows crosssection ( cm 2 ) inherent resistance compress. (N / mm) W extension (N / mm) , , PTFE-SHD- Expansion Joint 2 convolutes vacuum data max. temperature ( F) for full vacuum DN / F 230 / / / 4 / / 3 For compression forces: ompression force Fc = x S with from table, S = travel in mm. For extension forces: Extension force Fw = W x S with W from table, S = travel in mm. Please notice: - urves and chart are only valid at neutral length and with limit bolts in place. - The max. angular deflection is approx Above mentioned travel, misalignment or angular deflection are alternatives, i.e. the percentage values are not allowed to exceed % when added together. - Burst pressure is about 4x the indicated in the chart. - The figures stated are average values and apply to room temperature. Deviations due to processing variations are possible. - For abrasive applications the bellows (on request) can be equipped with a PTFEnozzle liner, flared on one side. Movements are then restricted. Savety instructions: - Follow install. instructions. - Do not exceed pressure / temperature rating shown in the appropriate bellows chart. - Safeguard the units in hazardous service. - Leave limit bolts in. Severe damage can result if they areremoved or altered. - Remove the flange covers only when ready to install the bellow - Insure that sealing faces are clean, smooth and parallel. - While installing the flanges, make sure the bolts do not jut out from the flange backside to the bellow. - Improperly installation or beyond the pressure / temperature rating may result in property damage or personal injury.

79 DN axial travel max. (+ mm) misalignment max. eff. bellows crosssection ( cm 2 ) inherent resistance compress. (N / mm) W extension (N / mm) , PTFE-SHD- Expansion Joint 3 convolutes , vacuum data max. temperature ( F) for full vacuum DN / F 230 / / / 4 / / 3 For compression forces: ompression force Fc = x S with from table, S = travel in mm. For extension forces: Extension force Fw = W x S with W from table, S = travel in mm. Please notice: - Above shown curves and chart are only valid at neutral length and with limit bolts in place. - The max. angular deflection is approx Above mentioned travel, misalignment or angular deflection are alternatives, i.e. the percentage values are not allowed to exceed % when added together. - Burst pressure is about 4x the indicated in the chart. - The figures stated are average values and apply to room temperature. Deviations due to processing variations are possible. - For abrasive applications the bellows (on request) can be equipped with a PTFEnozzle liner, flared on one side. Movements are then restricted. Savety instructions: - Follow install. instructions. - Do not exceed pressure / temperature rating shown in the appropriate bellows chart. - Safeguard the units in hazardous service. - Leave limit bolts in. Severe damage can result if they are removed or altered. - Remove the flange covers only when ready to install the bellow - Insure that sealing faces are clean, smooth and parallel. - While installing the flanges, make sure the bolts do not jut out from the flange backside to the bellow. - Improperly installation or beyond the pressure / temperature rating may result in property damage or personal injury. TDS-EU-DIN-J-E-04

80 DN axial travel max. (+ mm) misalignment max. eff. bellows crosssection ( cm 2 ) inherent resistance compress. (N / mm) W extension (N / mm) PTFE-SHD- Expansion Joint 5 convolutes For compression forces: ompression force Fc = x S with from table, S = travel in mm. For extension forces: Extension force Fw = W x S with W from table, S = travel in mm. Please notice: - Above shown curves and chart are only valid at neutral length and with limit bolts in place. - The max. angular deflection is approx.. - Above mentioned travel, misalignment or angular deflection are alternatives, i.e. the percentage values are not allowed to exceed % when added together. - Burst pressure is about 4x the indicated in the chart. ompared with the pressure curves of the 2- and 3-convolute bellows, it is here much lower because of the risk of buckling. - The figures stated are average values and apply to room temperature. Deviations due to processing variations are possible. - For abrasive applications the bellows (on request) can be equipped with a PTFEnozzle liner, flared on one side. Movements are then restricted. Savety instructions: - Follow install. instructions. - Do not exceed pressure / temperature rating shown in the appropriate bellows chart. - Safeguard the units in hazardous service. - Leave limit bolts in. Severe damage can result if they are removed or altered. - Remove the flange covers only when ready to install the bellow - Insure that sealing faces are clean, smooth and parallel. - While installing the flanges, make sure the bolts do not jut out from the flange backside to the bellow. - Improperly installation or beyond the pressure / temperature rating may result in property damage or personal injury.

81 DN axial movement n = 0 lateral movement angular movement torsion eff. bellow crosssection spring rate δ λ α Mt A cδ cλ cα cτ (+ mm) (+ mm) (grd) (knm) ( cm 2 ) (N/mm) (N/mm) (Nm/grd) (knm/grd) axial spring rate lateral spring rate angular torsional stress vacuum service at 72 F 23 5 ( 10 Pa) at 3 F ( 10 Pa) 5 2, , , ,5 2, , ,5 2, , , , , , , , PTFE-Expansion-Joint with SS Housing & Spacer Bead , , , , , , , , , 5 2, , , , , 9 1, , , , , , , , , , , 5 7, 8 667, , 2 932, , , , , , , , , , , , , , , , , , Reduction factors for application pressure, temperature related, acc. to flange material 1E1: temperature appl. pressure F bar , 5 6, 9 6, 2 psig Flange material to select according to service temperature. TDS-EU-DIN-K-E-04

82 DN 32 axial movement n = 0 lateral movement angular movement torsion eff. bellow crosssection spring rate δ λ α Mt A cδ cλ cα cτ (+ mm) (+ mm) (grd) (knm) ( cm 2 ) (N/mm) (N/mm) (Nm/grd) (knm/grd) axial spring rate lateral spring rate angular torsional stress vacuum service at 72 F 23 5 ( 10 Pa) at 3 F ( 10 Pa) 4 2, , , , , , , , , , ,5 3, PTFE-Expansion-Joint with SS Housing & Spacer Bead Flanges DIN PN 1 7 2, , , , , 5 1, , , , , , 6 2, , , 3 135, , , , , , , 9 1, ,5 7 1, 9 1, , , 4 3, , , , , , , ,5 2, , , , , , , , , 5 9, , Reduction factors for application pressure, temperature related, acc. to flange material 1E1: temperature appl. pressure F bar 18, 7 17, 2, 5 psig , Flange material to select according to service temperature.

83 2 onvoluted PTFE Expansion Joints with Reinforcing Rings DN Value not available in Value Select Option selection may affect manufacturing lead time. onsult factory for price and delivery Flanges of Flanges of onductive Liner Limit Bolt Inox A2 Reinforcing Ring Hastelloy Standard Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-E2T-SD-E-04

84 2 onvoluted PTFE Expansion Joints with Reinforcing Rings Dimensional Data DN L + 2% Thread S + 10 % d % d % Weight (ca. kg) 35 4 x M , x M , x M , x M , 5 4 x M , x M x M , , x M , x M , x M , 3 8 x M 2 5, x M 3 5, x M 370 5, x M x M , x M , x M , x M Part Number System 1 K2W 0 10 W P1 SS 00XX Type Finished Fitting Expansion Joint with 2 onvolutes Diameter Pressure 10 - Liner W - White E - Anti-Static Resin Type Paste Standard Flanges SS Standard Flanges

85 3 onvoluted PTFE Expansion Joints with Reinforcing Rings DN Value not available in Value Select Option selection may affect manufacturing lead time. onsult factory for price and delivery Flanges of Flanges of onductive Liner Limit Bolt Inox A2 Reinforcing Ring Hastelloy Standard Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-E3T-SD-E-04

86 3 onvoluted PTFE Expansion Joints with Reinforcing Rings Dimensional Data DN L + 2% Thread S + 10 % d % d % Weight (ca. kg) 45 4 x M , x M , x M , 7 4 x M , x M , x M x M , , x M x M , x M , x M 2 5, x M 3 5, x M 370 5, x M x M , x M , x M , x M Part Number System 1 K3W 0 10 W P1 SS 00XX Type Finished Fitting Expansion Joint with 3 onvolutes Diameter Pressure 10 - Liner W - White E - Anti-Static Resin Type Paste Standard Flanges SS Standard Flanges

87 5 onvoluted PTFE Expansion Joints with Reinforcing Rings DN Value not available in Value Select Option selection may affect manufacturing lead time. onsult factory for price and delivery Flanges of Flanges of onductive Liner Limit Bolt Inox A2 Reinforcing Ring Hastelloy Standard Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-E5T-SD-E-04

88 5 onvoluted PTFE Expansion Joints with Reinforcing Rings Dimensional Data DN L + 2% Thread S + 10 % d % d % Weight (ca. kg) 4 x M , 9 4 x M , 9 4 x M , 9 4 x M , x M x M x M , , x M , x M x M x M 2 5, x M 3 5, x M 370 5, x M x M , Part Number System 1 K5W 0 10 W P1 SS 00XX Type Finished Fitting Expansion Joint with 5 onvolutes Diameter Pressure 10 - Liner W - White E - Anti-Static Resin Type Paste Standard Flanges SS Standard Flansche

89 2 onvoluted PTFE SHD Expansion Joints with Reinforcing Rings DN Value not available in Value Select Optionen Option selection may affect manufacturing lead time. onsult factory for price and delivery Flanges of Flanges of onductive Liner Limit Bolt Inox A2 Reinforcing Ring Hastelloy Standard Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-E2T-HD-E-04

90 2 onvoluted PTFE SHD Expansion Joints with Reinforcing Rings Dimensional Data DN L + 3% Thread DIN 01 S min. S max. d % d % Weight (ca. kg) 36 4 x M , x M , x M12 2, , 39 4 x M16 78/88 2, , x M16 2, , x M , x M , , x M16 8 2, , x M , , x M , , x M 2 3, 5 6,75 4 0, x M 3 3, , x M , x M x M Part Number System 1 K2W 0 10 W P3 SS 00XX Type Finished Fitting SHD Expansion Joint with 2 onvolutes Diameter Pressure 10 - Liner W - White E - Anti-Static Resin Type Paste SHD Flanges SS Standard Flanges

91 3 onvoluted PTFE SHD Expansion Joints with Reinforcing Rings DN Value not available in Value Select Optionen Option selection may affect manufacturing lead time. onsult factory for price and delivery Flanges of Flanges of onductive Liner Limit Bolt Inox A2 Reinforcing Ring Hastelloy Standard Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-E3T-HD-E-04

92 3 onvoluted PTFE SHD Expansion Joints with Reinforcing Rings Dimensional Data DN L + 3% Thread DIN 01 S min. S max. d % d % Weight (ca. kg) 54 4 x M , x M , x M12 2, , x M16 78/88 2, , x M16 2, , x M , x M , , x M16 8 2, x M , , x M , , x M 2 3, 5 6, x M 3 3, x M , x M x M Part Number System 1 K3W 0 10 W P3 SS 00XX Type Finished Fitting SHD Expansion Joint with 3 onvolutes Diameter Pressure 10 - Liner W - White E - Anti-Static Resin Type Paste SHD Flanges SS Standard Flanges

93 5 onvoluted PTFE SHD Expansion Joints with Reinforcing Rings DN Value not available in Value Select Optionen Option selection may affect manufacturing lead time. onsult factory for price and delivery Flanges of Flanges of onductive Liner Limit Bolt Inox A2 Reinforcing Ring Hastelloy Standard Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-E5T-HD-E-04

94 5 onvoluted PTFE SHD Expansion Joints with Reinforcing Rings Dimensional Data DN L + 3% Thread S min. S max. DIN 01 d % d % Weight (ca. kg) 87 4 x M , x M , x M12 2, , x M16 78/88 2, , x M16 2, x M , x M , , x M16 8 2, , x M , , x M , , x M 2 3, 5 6, , x M 3 3, , x M , x M x M Part Number System 1 K5W 0 10 W P3 SS 00XX Type Finished Fitting SHD Expansion Joint with 5 onvolutes Diameter Pressure 10 - Liner W - White E - Anti-Static Resin Type Paste SHD Flanges SS Standard Flanges

95 PTFE-Expansion Joints with SS Housing and Spacer Bead TEFLON by DuPont DN 32-1 DN Value not available in Value Select Option selection may affect manufacturing lead time. onsult factory for price and delivery Flanges of Flanges Bellow of Bellow of Hastelloy 4 onductive Liner PN Standard Standard Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-EST-321-E-0904

96 PTFE-Expansion Joints with SS Housing and Spacer Bead DN 32-1 Dimensional Data per DN L + 5% - 1,5% S + 10 % + 5 % d % d % Weight (ca. kg) , , , , , Part Number System 1 EKS 10 W XX LLL1 XX Type Finished Fitting Stainless Steel Expansion Joint Diameter Pressure PN Liner W - White E - Anti-Static Resin Type Factory Defined Flanges LL L1 - loose /loose - Length 1 LL L2 - loose /loose - Length Flanges Flanges

97 PTFE-Expansion Joints with SS Housing and Spacer Bead TEFLON by DuPont DN - DN Value not available in Value Select Option selection may affect manufacturing lead time. onsult factory for price and delivery Flanges of Flanges Bellow of Bellow of Hastelloy 4 onductive Liner PN Standard Standard Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-EST--E-0904

98 PTFE-Expansion Joints with SS Housing and Spacer Bead DN - Dimensional Data per DN 0 L + 5% - 1,5% S + 10 % + 5 % d % d % Weight (ca. kg) , , , , Part Number System 1 EKS 0 10 W XX LLL1 XX Type Finished 329 6, , , , Fitting Stainless Steel Expansion Joint Diameter Pressure PN Liner W - White E - Anti-Static Resin Type Factory Defined Flanges LL L1 - loose /loose - Length 1 LL L2 - loose /loose - Length Flanges Flanges

99 PTFE-Expansion Joints with SS Housing and Spacer Bead (DIN PN ) TEFLON by DuPont DN 32-1 DN Value not available in Value Select PN Option selection may affect manufacturing lead time. onsult factory for price and delivery Flanges of Flanges Bellow of Bellow of Hastelloy 4 onductive Liner Standard Standard Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-EST-PN-321-E-0904

100 PTFE-Expansion Joints with SS Housing and Spacer Bead (DIN PN ) DN 32-1 Dimensional Data per PN DN L + 5% - 1,5% S + 10 % + 5 % d % d % Weight (ca. kg) , , , , Part Number System 1 EKS W XX LLL1 XX Type Finished Fitting Stainless Steel Expansion Joint Diameter Pressure PN Liner W - White E - Anti-Static Resin Type Factory Defined Flanges LL L1 - loose /loose - Length 1 LL L2 - loose /loose - Length Flanges Flanges

101 PTFE-Expansion Joints with SS Housing and Spacer Bead (DIN PN ) TEFLON by DuPont DN - DN Value not available in Value Select PN Option selection may affect manufacturing lead time. onsult factory for price and delivery Flanges of Flanges Bellow of Bellow of Hastelloy 4 onductive Liner Standard Standard Best Price & Lead Time (1-2 Weeks) Full Vacuum at 230 O L onger Lead Time (4-6 Weeks) Reduced Vacuum Resistance at Elevated Temp. Price and Delivery Upon Request Non-Vacuum Rated TDS-EU-DIN-EST-PN--E-0904

102 PTFE-Expansion Joints with SS Housing and Spacer Bead (DIN PN ) DN - Dimensional Data per PN DN 0 L + 5% - 1,5% S + 10 % + 5 % d % d % Weight (ca. kg) , , , , Part Number System 1 EKS 0 W XX LLL1 XX Type Finished 377 6, , , , Fitting Stainless Steel Expansion Joint Diameter Pressure PN Liner W - White E - Anti-Static Resin Type Factory Defined Flanges LL L1 - loose /loose - Length 1 LL L2 - loose /loose - Length Flanges Flanges