IP Link Device Interface Ethernet Communication Sheet

Transcription

1 This document provides additional assistance with wiring your Extron IP Link enabled product to your device. Different components may require a different wiring scheme than those listed below. For complete operating instructions, refer to the user s manual for the specific Extron IP Link enabled product or the controlled device manufacturer supplied documentation. Device Specifications: Device Type: Video Conference Manufacturer: Polycom Firmware Version: SoundStructure Studio Version: Model(s): SoundStructure C8 Minimum Software and Firmware Requirements: IP Link Compiler IP Link Firmware GC Version Version History: Driver Version Date Notes 10 4/10/2014 Added Call Status. 9 9/10/2013 Added Hold, Transfer, and Conference functionality. 8 1/18/2013 Added VoIP functionality, Dynamic Text, removed Mixers and levels. 6 2/17/2012 Extron Certified. Added Mute Mixers, Toggle states to all Mixers, Input Levels, Output Levels, Mixer Faders, Input Faders, Auto Answer, Hook now holds Flash and Redial states, changed the naming convention from "Phone Input" to "Receive" and from "Phone Out" to "Transmit". 3 10/12/2010 Extron Certified. Improved status polling. 2 9/30/2010 Extron Certified Version. Driver Notes: The Polycom Firmware must be or above for this driver to function as expected. Group Names are required for status. This driver must be loaded on an Extron product that has more than 1mb of usable memory. In order for this driver to work with the SoundStructure, it is necessary to configure the virtual names to match the driver within the SoundStructure Studio available for free from Polycom. The driver includes optimization to the features listed below: Dynamic Text b. Dialing Feedback c. Volume Page 1 of 8

2 Making a conference or transferring a call Dial initial number and press hook off to dial out once connected do the following: Press Conference or Transfer Dial Secondary number Press Hook Off Virtual Names should be labeled as below Table 1 Input/Output Type Driver Name Virtual Name Group Name* Mics Mute/Fader/Step Input 1 8 Input 1 8 Mics Amplifiers Mute/Fader/Step Output 1 8 Output 1 8 Outputs Hook Phone_connect Hook Phone Out Flash Phone_flash Hook Flash Phone Out Redial Phone_redial Hook Redial Phone Out Dialing Keypad Phone_dial Dial Keypad Phone Out Phone Output Mute/Fader/Step Phone Transmit Phone Out Phone Input Mute/Fader/Step Phone Receive Phone In Auto Answer phone_auto_answer_en Auto Answer Phone In Hook Phone_connect Hook VoIP Out Dialing Keypad Phone_dial Dial Keypad VoIP Out Phone Output Mute/Fader/Step Phone Transmit VoIP Out Phone Input Mute/Fader/Step Phone Receive VoIP In Auto Answer phone_auto_answer_en Auto Answer VoIP In *Group Names are necessary for group control and status. Each physical input and output must be configured with a virtual name. All Inputs should be labeled as above. o It is recommended to make a group named Mics and add all the Inputs into this group (created by default in Studio). All Amplifiers should be labeled as above. o It is recommended to make a group named Outputs and add all the Outputs into this group. Example: Presets 1 16 must be labeled as Preset x (where x is 1 16). Refer to SoundStructure Design manual for more information. Page 2 of 8

3 Virtual Channel Names: Select the Channels branch under the SoundStructure System Select the Edit Channels button on the top of the page Channels in the system are in the Channels Defined box. Page 3 of 8

4 Group Names: Select the Channels branch under the SoundStructure System Select the Edit Groups button on the top of the page Groups in the system are defined in the Channel Groups box. Page 4 of 8

5 Dialing Configuration: The Keypad is configured to display the digits on the field located at the top of the page. When the desired number is entered, press the Call button and that will connect you with the number you entered. When in a call, the keypad will be used the same as the DTMF tone where each number press will get sent out immediately. The Delete button will delete the last number displayed on the touch panel and is configured with the press/repeat functionality. The Clear button will clear all numbers entered. The Label on the top of the page, Please enter a number and press Call, is configured in GUI Configurator with an ID of and with the Dynamic text parameter enabled. Page 5 of 8

6 Control Commands & States: Auto Answer On Off Toggle Call Type Analog VoIP Dynamic ID Dial Keypad 0-9 # *,. Clear Delete Do Not Disturb Mode On Off Hook On Off Flash Redial Transfer Conference Hold Input 1-8 Fade (Discrete) -100 to 20 in steps of 2 Input 1-8 Fade (Step) Up Down Input Group Fade -100 to 20 in steps of 2 Mute All Inputs On Off Toggle Mute All Outputs On Off Toggle Mute Input 1 8 On Off Toggle Mute Output 1 8 On Off Toggle Output 1-8 Fade Level (Discrete) Output 1-8 Fade Level (Step) -100 to 20 in steps of 2 Up Down Output Group Fade Level -100 to 20 in steps of 2 Phone Receive Fader -100 to 20 in steps of 2 Phone Receive Fader (Step) Up Down Phone Transmit Fader -100 to 20 in steps of 2 Phone Transmit Fader (Step) Up Down Preset Recall 1-16 Receive Mute On Off Toggle Page 6 of 8

7 Transmit Mute On Off Toggle VoIP Dial Mode Number URL Status Available: Auto Answer On Off Call Type Analog URL Call Status Call in Progress 2 Connected 2 Ringing 1 Not Ringing 1 Not In Call 2 Status Unavailable Connection Status Connected Disconnected Do Not Disturb Mode On Off Hook On Off Input 1-8 Fader(Discrete) -100 to 20 in steps of 2 Mute Input 1 8 On Off Mute Output 1 8 On Off Phone Receive Fader -100 to 20 in steps of 2 Phone Transmit Fader -100 to 20 in steps of 2 Receive Mute On Off Transmit Mute On Off Phone Receive Fader -100 to 20 in steps of 2 VoIP Dial Mode Number URL Call Status 1 only apply for Analog Call Status 2 only apply for VoIP Page 7 of 8

8 Network communication: When configuring the Ethernet driver, be sure device settings match that of the GC configuration. Port Type: Ethernet Logon Credentials No Supported: Default Port: Multi-Connection Yes Capable: Port Changeable: Yes Ethernet Driver Configuration Description: Please refer to user manual for settings the network communication parameters. Notes for the Device: Page 8 of 8