Draft Indian Standard Guidelines for Protection of Below Ground Structures Against Water from the Ground

Transcription

1 BUREAU OF INDIAN STANDARDS MANAK BHAVAN, 9 BAHADUR SHAH ZAFAR MARG, NEW DELHI Phone: , , Extn 4434; Fax: sak.bis@nic.in DRAFT STANDARD IN WIDE CIRCULATION DOCUMENT DESPATCH ADVICE Reference Date CED 41/T October 2013 TECHNICAL COMMITTEE: Water-Proofing and Damp-Proofing Sectional Committee, CED 41 ADDRESSED TO : 1. All Interested Members of Civil Engineering Division Council, CEDC 2. All Members of CED All others interested Dear Sirs, Please find enclosed the following draft: Doc No. CED 41 (7903) Title Draft Indian Standard Guidelines for Protection of Below Ground Structures Against Water from the Ground Kindly examine the draft standard and forward your views stating any difficulties which you are likely to experience in your business or profession, if this is finally adopted as National Standard. Last Date for comments: 15 December Comments if any, may please be made in the format as given overleaf and mailed to the undersigned at sak.bis@nic.in. In case no comments are received or comments received are of editorial nature, you will kindly permit us to presume your approval for the above document as finalized. However, in case comments of technical in nature are received, then it may be finalized either in consultation with the Chairman, Sectional Committee or referred to the Sectional Committee for further necessary action if so desired by the Chairman, Sectional Committee. This document is also hosted on the BIS website Thanking you, Yours faithfully, -sd- (J. Roy Chowdhury) Sc F & Head (Civil Engg.) Encl: as above 1

2 FORMAT FOR SENDING COMMENTS ON BIS DOCUMENT [Please use A4 size sheet of paper only and type within fields indicated. Information in column (3) should include reasons for comments, technical references and suggestions for modified wording of the clause when the existing text is found not acceptable. Comments through shall be appreciated.] Name of the Commentator/ Organization: BIS Document No.: Title: Wide Circulation Draft Indian Standard PROTECTION OF BELOW GROUND STRUCTURES AGAINST WATER FROM THE GROUND - GUIDELINES BIS Letter Reference No. CED 41/T-45 Dated 07 Oct 2013 Clause/ Table No. Comments/ Modified Wordings Justification of Proposed Change (1) (2) (3) 1

3 DRAFT FOR COMMENTS ONLY (Not to be reproduced without the permission of BIS or used as an Indian Standard) भ रत य म नक मस द क व य पक क पक चरल न जम न स न ल क स रलन ओ क जम न स पक न क व र द ध स रक षण क ददश ननद श Wide Circulation Draft Indian Standard GUIDELINES FOR PROTECTION OF BELOW GROUND STRUCTURES AGAINST WATER FROM THE GROUND ICS BIS 201* B U R E A U O F I N D I A N S T A N D A R D S MANAK BHAVAN, 9 BAHADUR SHAH ZAFAR MARG NEW DELHI

4 Draft Indian Standard PROTECTION OF BELOW GROUND STRUCTURES AGAINST WATER FROM THE GROUND GUIDELINES Doc: Water Proofing and Last Date for Receipt of Comments Damp Proofing Sectional Committee, CED 41 is 15 December 2013 FOREWORD Formal clause shall be added later. Different types of waterproofing materials are used in the building industry. In order to obtain satisfactory performance, it is essential that prior to the application of these materials for the damp-proofing and water-proofing treatment, special care has to be taken to design the details and carefully prepare the building surface for receiving the treatment as recommended. This standard provides guidance for the water-proofing treatment of structures below ground. It is essential to ensure the water tightness/protection from water of the structures so that the flow of water from inside the structure to outside (in case of swimming pools), and the infiltration of water from the surrounding soil into the structure are effectively prevented. This standard is intended to provide guidance to the designers, engineers, contractors and others engaged in building activity to ensure protection of below ground structures against water. A number of recent developments are addressed, which are important when specifying, designing and constructing below ground structures, including: 1) more deep construction in congested urban areas; 2) an increase in the provision of residential basements; 3) development and use of new materials for waterproofing; 4) a more detailed assessment is provided of the risks inherent in below ground construction and how these might best be addressed. It is to be noted that the figures used in this document are only representative of different installation methods, and should not be translated directly into practice without first checking all the parameters specific to the installation. In the formulation of this standard due weightage has been given to international co-ordination among the standards and practices prevailing in different countries in addition to relating it to the practices in the field in this country. This has been met by deriving assistance from BS 8102:2009 Code of practice for protection of below ground structures against water from the ground published by the British Standards Institution. This draft Indian standard is developed to suit Indian context and is largely based on the technical provisions given therein. This Standard has been formulated to serve as a useful guidance and suggest recommendations for planning and carrying out water proofing activity. It should not be quoted as if it were a specification and particular care should be taken to ensure that claims of compliance are not misleading. It has been assumed in the drafting of this standard that the execution of its provisions is entrusted to suitably qualified and experienced people, for whose guidance it has been prepared. For the purpose of deciding whether a particular requirement of this standard is complied with, the final value, observed or calculated, expressing the result of a test or analysis, shall be rounded off in accordance with IS 2:1960 Rules for rounding off numerical values (revised). The number of significant places retained in the rounded off value should be the same as that of the specified value in this standard. 3

5 DRAFT FOR COMMENTS ONLY (Not to be reproduced without the permission of BIS or used as an Indian Standard) Wide Circulation Draft Indian Standard PROTECTION OF BELOW GROUND STRUCTURES AGAINST WATER FROM THE GROUND GUIDELINES Doc: 1 SCOPE This standard gives recommendations and provides guidance on methods of dealing with and preventing the entry of water from surrounding ground into a structure below ground level. It covers the use of: a) waterproofing barrier materials applied to the structure, b) structurally integral watertight construction; and c) drained cavity construction. It also covers the evaluation of groundwater conditions, risk assessment and options for drainage outside the structure. It applies to structures which extend below ground level and those on sloping sites. This standard does not give recommendations concerning the use of embedded heating in structures, floors and walls or for the special requirements in connection with the design and construction of cold stores. NOTE Structures are generally characterized as deep if they have more than one storey below ground level, or shallow if they have only a single storey below ground. This standard is applicable to both. 2 REFERENCES The standards listed in Annex A contain provision which through reference in this text, constitute provisions of this standard. At the time of publication, the editions indicated were valid. All standards are subject to revision and parties to agreement based on this standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated in Annex A. 3 TERMINOLOGY For the purposes of this Standard, the following definitions shall apply in addition to those given in IS 4911 and IS 6461 (Part 7): 3.1 Cavity drain membrane Dimpled, flexible, high-density polymer sheet, which can be placed against the internal face of a structure after construction and is designed to intercept water 4 penetrating the structure and direct it to a drainage system. 3.2 Cut-off wall Embedded retaining wall (see 3.4) designed to surround and seal-off an area, to inhibit water inflow from the surrounding area. 3.3 Damp area Area which, when touched, might leave a light film of moisture on the hand but no droplets of water (that is beading). 3.4 Embedded retaining wall Wall used to support the sides of an excavation, installed in advance and penetrating below the lowest level of the below ground construction. NOTE Within this standard the principal forms considered constitute the primary permanent wall for the below ground construction, and are taken as diaphragm walls, contiguous or secant piles (which may be installed in different configurations) or steel sheet piles. 3.5 Ground barrier Impermeable barrier between the structure and the ground intended to prevent or impede the ingress of water, dampness, radon, methane and other ground gases and contaminants. 3.6 Loading coat Layer of material designed to hold a Type A waterproofing material in place when resisting water pressure. 3.7 Perched water table Reservoir of water in the ground maintained permanently or temporarily above the standing water level in the ground below it, and is caused by the presence of an impervious soil or a stratum of low permeability. 3.8 Seepage Slow transmission of water through discrete pathways of a structure. 3.9 Tanking Application of an appropriate waterproofing barrier to the walls, the base slab and, where relevant, the roof of a below ground structure, such that the entire envelope of the structure below ground is protected against water ingress. NOTE A cavity drain membrane is not considered to constitute tanking.

6 3.10 Type A (barrier) protection Protection against water ingress which is dependent on a separate barrier system applied to the structure Type B (structurally integral) protection Protection against water ingress which is provided by the structure Type C (drained) protection Protection against water ingress into usable spaces which is provided by the incorporation of an appropriate internal water management system Vapour check Membrane or other element that restricts the transmission of water vapour Waterproof Impervious to water. NOTE This can also be known as watertight Waterproofing Application of waterproof/ water-resisting materials Waterproofing barrier Material that does not permit the transmission of free water, but might allow some water vapour permeability Waterproofing system Materials and methods used to protect a structure from water ingress and might also provide resistance to the diffusion of water vapour Water resistance Ability of a material to resist water penetration Waterstop Material designed to inhibit the transmission of water through joints in the structure Water vapour Water in its gaseous state Water vapour resistance Ability of a material to resist water vapour penetration. 4 DESIGN PHILOSOPHIES 4.1 General It is essential for the success of any project involving below ground structures that strategies for dealing with groundwater, soil gases and contaminants are considered from the very earliest stages of the planning and design processes. For guidance on construction project management, a reference may be made to IS (Part 1). For new structures, it is recommended that the structural design, overall weatherproofing design, waterproofing design and construction processes are considered together, as they generally interact. In addition, it is recommended that, during the design process and at all stages of the 5 construction process, the designers, specialists, manufacturers/suppliers and installing contractors establish and maintain effective channels of communication. Regular and clear communication coupled with good site supervision allows variations and amendments to the design to be planned and executed without compromising the performance of the waterproofed structure (see also 4.2). 4.2 Design team The advice of a geotechnical specialist should be sought on the geology and hydrogeology, the external drainage options and groundwater conditions (see 5). A waterproofing specialist should be included as part of the design team so that an integrated waterproofing solution is created. The waterproofing specialist should: a) be suitably experienced; b) be capable of devising solutions that accommodate the various project constraints and needs; c) provide the design team with information and guidance that assists with and influences the design, installation and future maintenance of the waterproofed structure. NOTE The waterproofing specialist could be the manufacturer or material supplier, provided that the manufacturer/supplier has the relevant expertise. All design decisions made by others that might have an impact on the waterproofing design should be brought to the attention of the waterproofing specialist/designer and installing contractors. Final decisions and any recommendations should be approved by the designer/engineer-in-charge. 4.3 Principal considerations General In order to develop a robust design for protecting a structure against groundwater, the following factors should be assessed: a) the likely highest level of the water table, the drainage characteristics of the soil and other site specific properties (see 5); b) the appropriate waterproofing measures (see 6), i.e. Type A, B or C protection and, where necessary, external drainage based on: 1) the results of the site evaluation, including the classification of the water table; and 2) the intended use of structure, with consideration given to any requirement for future flexibility. This should be undertaken in consultation with the client; c) the appropriate type of primary waterproofing system (see 8, 9 and 10).

7 NOTES 1 The general principle is to assess the risk of water reaching the structure and then to select a waterproofing system capable of achieving the required internal environment. 2 Mechanical heating and ventilation often play an important role in creating the internal environment, particularly where higher grades are required. The design of such systems is a specialist activity, outside the scope of this standard. Condensation may also be controlled by the provision of adequate ventilation (assisted by heating), coupled with the suitable treatment of floor and wall surfaces. A three-dimensional review of structure and waterproofing should be undertaken so as to identify any complex geometries, which are not readily identified from normal two-dimensional details. Service entries are particularly vulnerable to water penetration; where they cannot be avoided, they should be carefully detailed, incorporating sealing, to minimize the risk of water ingress (see 8.1.3). NOTE The three-dimensional review needs to include detailed information on the proposed waterproofing system (e.g. the effect that this has on wall base details, laps in membranes and waterstops). Examples of complex geometries are corner details and where the wall adjoins: the base slab/foundation; the superstructure; differing floor levels; and windows below ground Defects and Remedial Measures An ideal waterproofing solution would be defect-free. However, it should be noted that two types of defects might occur in any waterproofing, where a structure is subjected to water pressure, and this could mean that the required internal environment is not achieved. These defects are as follows: a) defects owing to poor workmanship or the inappropriate use of materials; b) defects owing to the specific properties of the materials being used. NOTE Reference to defects does not apply to normal designed flexural cracks or surface crazing in concrete elements but only to through cracking, which might need to be locally sealed. It is essential that the construction methods and materials used to realize the design are such that the defects in (a) are avoided. The defects in (b), which are generally minor, should be recognized and catered for in the design. Contingency planning for dealing with any localized defects or system failure that arise should be included as part of the overall waterresisting design for the structure (see also 11). In either case, the issue of repair ability should be taken into account and the feasibility of remedial measures assessed. Fig. 1 outlines the principal factors and stages that need to be addressed in order to produce a robust waterproofing solution for a below ground structure. It demonstrates that some matters are interrelated and that a degree of iteration might result from a need to address buildability and repairability. The principal issues (boxes) do not necessarily need to be addressed in the order shown but all need to be understood and evaluated. 6

8 FIG. 1 DESIGN FLOWCHART 5 SITE EVALUATIONS NOTE Attention is drawn to the fact that many of the issues addressed in this clause are also relevant to the design of the structure itself. 5.1 General Desk Study A desk study should be carried out; a) to assess the geology and hydrogeology, including soil permeabilities, flood risk, radon, methane and other ground gases and contaminants (e.g. chlorides and acids); 7 b) to assess the topography of the surrounding ground in relation to the below ground structure; c) to establish the likely highest level of the water table and the potential for the occurrence of a perched water table; and d) to identify any missing ground and groundwater information, which should then be obtained by undertaking a site investigation Risk Assessment NOTE The principal risks with respect to water ingress into structures are the external environmental conditions. A risk assessment should be carried out which considers the long-term water pressures, the effects

9 of surface water infiltration and the use of external drainage and cut-off walls. Risk assessment should also consider: a) The effects of climate change, burst water mains and sewers, adjacent trees, sulfates, radon, methane and other ground gases and contaminants; and b) Where external drainage is proposed, the effects of drawdown on adjacent structures, the potential silting of drainage and befouling issues. Even when the site investigation indicates dry conditions, the risk of some water logging (see Note) in the future should be assumed. NOTE Even in permeable subsoil, groundwater requires time to drain away and this can result in limited pressure periodically coming to bear against the structure. The following consequences of Failure should be analyzed when doing desk study: a) Disputes costs, legal fees b) Private or public property damage liability c) Endangerment of building operative or public from damage to electrical equipment d) Damage to archives, stored goods or plant e) Loss of rent f) Reduction in value of property g) Damage to reputation of landlord/developer h) Facility, business disruption i) Lack of access/utility of basement areas j) Costs of remedial work and operational delays Water Table Classification Where assessment of the water table is undertaken, this should be classed into the following three categories, which can then be used to determine the suitability of different types of waterproofing protection (see 6.2). a) High where the water table or perched water table is assessed to be permanently above the underside of the base slab. b) Low where the water table or perched water table is assessed to be permanently below the underside of the base slab. This only applies to free-draining strata. c) Variable where the water table fluctuates. NOTE In certain ground conditions, external drainage systems can be used to convert the high and variable water tables to the low condition (see also 6.3) Inspection and Survey for Existing Structures General Following an assessment of the external risk (see 5.1.2), a comprehensive survey should be undertaken of any existing waterproofing arrangements. The structure should also be examined in order to determine any potential movement that might occur between the walls and floor. NOTES 1 The base slab of many older structures is likely to abut the external walls. This can give rise to movement between wall and floor. Special flexible joint details might be required so that strains in the waterproofing materials are controlled within acceptable limits where bonded or surface-applied barrier materials are used in such situations. Similar details might also be required at other locations where structural movement can occur. 2 Less movement would be expected in cases where the floor is set into the wall although horizontal movement can occur unless the floor is reinforced such as to achieve the necessary fixity. As the space available in below ground structures is often converted into habitable rooms during refurbishments, the survey should also consider the previous use, e.g. this might have been such that dampness was of less concern than for the proposed use. NOTE Existing waterproofing might have to be removed completely and replaced with an entirely new system, although in some instances it might be possible to apply a Type A barrier or a Type C drained cavity system directly. These systems can be considered where there is no existing waterproofing but the suitability of Type A barrier materials depends on the characteristics of the surface of the wall or floor External Walls An old external cavity form of waterproofing protection might be encountered that is not immediately obvious. Where an external cavity is found, it should be inspected to confirm that: a) the cavity is not bridged by debris; b) any drainage is still functioning and has not been silted up; and c) air bricks are not obstructed by soil or vegetation. NOTE An example of an external cavity is where an inner wall, load bearing or otherwise, has been built with a cavity between it and an earlier retaining wall. This cavity might be closed/capped with a plinth, and would typically be drained at the base and ventilated by air bricks. It should be established whether walls are earth retaining or free standing as there might be instances where the waterproofing measures have

10 not been continued along internal walls abutting the external retaining wall. NOTE Where the external wall is of solid construction, there might be no waterproofing or there might have been previous attempts to mask dampness. Many such applications can be incomplete or ineffective. It is possible that the attempted waterproofing was inappropriate for the prevailing external conditions or the wall surface to which it had been applied. The survey should include any constructions which abut the main structure, such as garden walls and arches under steps, as these are a potential source of moisture transfer Floor Where drainage tiles have been used to cover the floor, they should be assessed to confirm that they have sufficient strength to withstand loadings from walls, plant, equipment, vehicles, etc., appropriate to the intended use. Where no-fines concrete has been used as a drainage layer, this should be similarly assessed to confirm that it has sufficient strength to withstand loadings and is still draining effectively. NOTES 1 Drainage tiles are typically made from clay or concrete. Both tiles and no-fines concrete have widely been replaced by cavity drain membranes. The floor should be thoroughly surveyed for signs of moisture penetration. 2 Moisture from the ground can move across abutting constructions at any level and in some conditions running water might be encountered. Consideration should also be given to: a) the ability of any surface to accept the proposed waterproofing; b) the effect that any proposed waterproofing system is likely to have on stresses imposed on the existing structure by groundwater once the waterproofing system has been installed. 6 WATER-RESISTING DESIGN 6.1 Groundwater Waterproofing measures should be designed on the basis of water to the full height of the retained ground at some time during the structure s life where: a) no detailed geological or hydrogeological assessment has been undertaken; b) the results of the soil investigations are inconclusive with respect to groundwater; c) the ground drainage characteristics are unreliable; d) the drainage measures (either internal or external) are unreliable or un-maintainable and infiltration cannot be controlled. 9 Protection against water ingress from the following three sources should be considered: 1) the inflow of surface water, ranging from percolation of rain to inundation of water from burst water mains (see 6.3); 2) the water pressures acting on the external retaining wall system; 3) the water pressures below the base slab. The water-resisting design should enable the system to withstand a pre-determined head of water or control the water before it reaches the structure. One or both of the following methods may be used, in conjunction with the waterproofing protection (see 6.2), to reduce water penetration, depending on the conditions of the site and the required internal environment: i) exclusion of surface water (see 6.3); ii) sub-surface drainage (see 6.4). 6.2 Waterproofing protection General One, or a combination, of the following types of waterproofing protection should be selected: a) Type A (barrier) protection; b) Type B (structurally integral) protection; c) Type C (drained) protection. When making this selection, consideration should be given to: 1) the need for combined protection (see 6.2.2); 2) the water table classification and required performance level (see 6.2.3); 3) the need for continuity in the protection (see 6.2.4). NOTE Examples of the three types of waterproofing protection are given in Fig. 2. There is a range of waterproofing systems that can be incorporated in each type of waterproofing protection and these should be assessed in accordance with 8, 9 and 10, as appropriate, and relevant manufacturers data sheets to confirm that the system selected is suitable for the structure to which it is to be applied. It is noted that the manufacturer s recommendations for installation, including provision of protection, should always be followed. Similarly, recommendations for fixings where proprietary products are used should be followed. In cases where the below ground structure is fully buried or the substructure extends beyond the superstructure, protection should be provided against water ingress through the roof slab, for example by:

11 i) encouraging water to drain away from the structure; ii) providing drainage above the roof slab; iii) using an external barrier. For existing structures, the following types of waterproofing systems should be considered, subject to their suitability for application and their ability to be repaired: an internal Type A waterproofing barrier on a structure of suitable strength and stiffness, built of concrete or masonry (subject to the condition of the surface) [see Fig. 2a)]; a drained cavity to the walls and floor, using a Type C cavity drain system [see Fig. 2c)]. In situations where the use of a waterproofing system covered by this standard is either not achievable or not cost effective, other methods may be used if they can be shown to lead to similar results. However, the risks and implications of such methods should be investigated and recorded Combined Protection Consideration should be given to the use of combined protection (i.e. Type A and Type B, Type A and Type C or Type B and Type C) where in a single system: a) the assessed risks are deemed to be high (see 5); b) the consequences of failure to achieve the required internal environment are too high; or c) additional vapour checks are necessary for a system where unacceptable water vapour transmission can occur. Although structures with Type B protection are designed to be water resistant, additional waterproofing systems may be applied internally or externally to control water vapour movement, where appropriate. An in-situ liner wall designed to provide Type B protection can be cast inside an embedded retaining wall to provide combined protection. In some cases, a fully bonded barrier might also be provided between the two elements. Although structures with Type C protection are designed to control and manage seepage into a structure, where this is unacceptably high the water resistance of the structure should be improved prior to the installation of the Type C protection, by the application of either Type A or Type B protection. When combining types of protection, the compatibility of the different protection types should be assessed in order to minimize the risks and negate the need for remedial measures. Key 1 External waterproofing 2 Masonry or concrete wall, as appropriate (see Table 1) 3 Concrete floor slab 4 Sandwiched waterproofing 5 Loading coat 6 Internal waterproofing FIG. 2(a) TYPE A (BARRIER) PROTECTION 10

12 Key 1 Water resistant reinforced concrete wall and slab 2 External or internal (within wall) waterstop, as required 3 Waterstop required at junction between wall and slab and at all construction joints 4 Concrete/steel piled wall 5 Water-resistant reinforced concrete floor slab or slab with added barrier 6 Waterstop at junction to follow profile of wall 7 Piled wall might need to be faced to achieve desired water resistance (see Table 1) FIG. 2(b) TYPE B (STRUCTURALLY INTEGRAL) PROTECTION Key 1 Cavity drain membrane 2 Inner skin (render, drylining or walling, depending on system) 3 Maintainable drainage channel with pipe connection to suitable discharge point 4 Sump formed in-situ or preformed 5 Pump 6 Wall cavity 7 Reinforced concrete/steel pile or diaphragm wall 8 Drainage channel 9 Waterstop at junction to follow wall profile 10 Internal block wall 11 Access point(s) to drainage 12 Floor slab with integral protection and/or added membrane (internal or external) FIG. 2(c) TYPE C (DRAINED) PROTECTION Water Table Classification and Grades of Waterproofing Protection When selecting a type of waterproofing protection, Table 1 and Table 2 should be taken into account, in conjunction with the following: 11 a) During the life of the structure, some degree of groundwater pressure is likely to build up against the chosen waterproofing system. b) Cracking or defective construction joints can provide a potential path for water ingress.

13 c) Water ingress can occur where there is groundwater pressure. If this is not consistent with the required performance level (see Table 2): 1) consideration should be given to the form and feasibility of remedial work; 2) if remedial work is not possible, the design should be altered. d) There are a number of risks associated with not carrying out planned maintenance for structures with Type C protection, e.g. pump failure (see 10.3). The designer should discuss these points with the client prior to deciding on which type(s) of waterproofing protection to use. The following should also be taken into account: 1) initial capital costs compared with costs for future maintenance and any necessary upgrades; 2) the scope for testing during installation; 3) the risks associated with aggressive groundwater and other ground contaminants, which might require the use of a specific protection barrier; 4) the need or ability to provide heating and/or ventilation and the consequences arising in terms of water vapour. NOTE This might call for the adoption of an improved grade of waterproofing protection (see Table 1 and 6.2.2) or active environmental control in order to manage water vapour (see Table 2). Table 1 Use of Different Protection Types Based on Water Table Classification (Clause 6.2.3) Risk associated with water table Low High Measure to reduce risk Water table classification (see note) Waterproofing protection Type A Type B Type C Piled Wall Reinforced concrete wall Low Acceptable Acceptable Acceptable Acceptable Variable Acceptable if the Acceptable where: Acceptable Acceptable variable classification a) The piled wall is directly is due to surface accessible for repair and water. The maintenance from inside manufacturer s the structure; or advice should be b) The piled wall is sought. combined with a fully High Acceptable where: a) An appropriate cementitious multicoat render or cementitious coatings are used; b) The wall is of concrete bonded waterproofing barrier; or c) The piled wall is faced internally with a concrete wall. Acceptable Acceptable Use combined protection Incorporate appropriately designed sub-surface drainage and ensure that this is maintained Use a fully bonded waterproofing barrier Lower the permeability of the main structure wall Use concrete with a waterproofing admixture Ensure that discharge systems, e.g. pumps are maintaned so that the system remains effective NOTE The water table classifications are defined as follows (see also 5.1.3) 1. Low where the water table or perched water table is assessed to be permanently below the underside of the base slab. This only applies to free drainage strata. 2. Varibale where water table fluctuates. 3. High where the water table or perched water table is assessed to be permanently above the underside of the base slab. 4. Ground permeability might affect risk under a low or varibale water table (see 5.1) 12

14 Table 2 Grades of Waterproofing Protection (Clause 6.2.3) Grade Example of use of structure Performance level 1 Car parking, plant rooms (excluding electrical equipments) 2 Car parking, plant rooms (utilities) and workshops requiring a drier environment (than Grade 1), storage areas Some seepage and damp areas tolerable, dependent on the intended use *. No water penetration acceptable Damp areas tolerable, ventilation might be required 3 Ventilated residential and commercial areas, including offices, restaurants, retails shops, leisure centers, Car parking etc. No water penetration acceptable Ventilation, dehumidification or air conditioning necessary, appropriate to the intended use * Seepage and damp areas for some forms of construction can be quantified by reference to available Industry Standards Continuity of Waterproofing Protection The need for continuity in the waterproofing protection should also be considered when selecting a type of protection. In most circumstances, the protection should be continuous. In certain situations, for example, where a drained cavity is combined with an underslab membrane, discontinuity with respect to waterproofing can be acceptable subject to careful detailing and an appropriate assessment of risk (see and Note 2). Any build up of water should be permanently controlled by a water management system. The proposed type of foundation and its suitability for providing continuity of waterproofing (where so required) should be assessed. NOTES 1 Continuity can be provided in situations where the surface or structure of the wall and foundation provides uninterrupted positioning of the waterproofing measures. In existing structures, assessment of any direct or potential discontinuity should be undertaken in order to determine the need for special waterproofing details, for example to overcome the effects of future movement. 2 Discontinuity of waterproofing protection might not be acceptable if there is a need to manage radon, methane and other ground gases and contaminants (see 6.5). 6.3 Exclusion of Surface Water Where practicable, provision should be made to prevent or reduce percolation of rainwater into the ground. NOTE Burst water mains and leaky sewers can provide additional sources of surface water. These can affect perched water tables. The drainage behind the wall needs to be able to cope with the highest inflow rates, e.g. the burst water main, which might not be practicable in coarse grained soils. 6.4 Sub-surface drainage Where sub-surface drainage is deemed necessary to lower the potential for hydrostatic pressure on the 13 waterproofing system and lessen the risk of water ingress through defects, it should be provided by one of the following methods: a) permeable granular fill; b) no-fines or hollow block work; c) geosynthetic drainage composite; d) underslab drainage. NOTE 1 Fig. 3 gives examples of the positioning of land drains, drainage channels and sub-surface drainage. Such provisions should be made maintainable where they are used to control the level of water in a structure that does not in itself provide adequate water resistance. Where practicable, water should be kept from prolonged contact with perimeter structure walls or base slabs by porous or open jointed land drains, combined with a geosynthetic drainage composite installed to the full height of the earth-retaining wall and laid to proper falls around the perimeter of the structure, adjacent to the wall footing and, where appropriate, beneath the slab itself. The sub surface system should be graded to an open outlet below the level of the lowest slab, such as to a stormwater drain protected by a pumped surcharge device or to a pumped sump, and can also provide a suitable outfall for any sub-floor drainage. Perimeter drainage at floor level is likely to lower the groundwater table to a degree that varies with the permeability of the subsoil and the possible consequences of this (such as permanent lowering of the water table in the surrounding area) should be taken into account. Any existing system of land drains should be tested, checked and only retained if both appropriate and maintainable. Any local diversions necessary should retain the existing geometry so far as practicable with new and easily maintainable pipework.

15 Care should be taken so that no damage is caused in nearby structures. Where deep structures are contemplated in built up areas, groundwater lowering should not be undertaken without careful investigation in conjunction with a groundwater specialist (see 4.2). Perimeter walls providing a cut off into an impervious layer or stabilization of granular subsoils by grout injection or similar alternative treatments may be considered instead. NOTE 2 For structures in coarse-grained soil, with variable and high water tables (see 5.1.3), the flow rates are likely to make it impracticable to pump for the design life of the structure. In these cases, a hydraulic cut off wall into fine-grained soils is required to isolate the ground below the base slab. This enables an underslab drainage system to relieve the water pressure below the base slab. NOTE 3 For structures in fine-grained soil, with variable and high water tables (see 5.1.3), the flow rates are more likely to make it practical to pump for the design life of the structure. A drainage system may be provided outside the retaining wall to control the water pressures. An underslab drainage system may also be provided below the base slab to control the water pressures. Cut-off walls are formed from diaphragm walls, secant piles or steel piles. Over the excavated wall depth remedial works can be carried out on leaky walls. This is not feasible for the length of wall below formation. Therefore, specified tolerances should be such that there is adequate intersection between piles or provision of continuous water bars at diaphragm wall panel joints and particular attention should be given to workmanship. In interbedded soils, relief wells may be used below formation level. The cut-off wall may also be used to reduce the flow rate and control the drawdown outside the site. FIG. 3 (a) CONSTRUCTION WITHOUT A TOE FIG. 3 (b) CONSTRUCTION WITH A TOE Key 1 Maintainable land drain (see 6.4) not to be positioned closer than a line of from the underside of the slab/blinding or with an invert above the upper surface of the floor slab 2 Measures to control water vapour might be necessary where the invert of the land drain is above the underside of the floor slab 3 Incorrect position of land drain, which can cause hydrostatic pressure on barrier leading to water ingress, if defects are present. 4 Subsoil drainage layer, where appropriate (see 6.4) 5 Structural wall slab and foundation slab FIG. 3 SUB-SURFACE DRAINAGE POSITIONING 14

16 6.5 Ground Gases The insertion of a ground barrier for the prevention of radon, methane and other ground gases and contaminants from entering a structure should be considered in the design, choice of the materials and installation of any waterproofing system. 7 GENERAL CONSTRUCTION ISSUES 7.1 Site De-watering Where appropriate, the site should be de-watered at least until such time as the below ground structure and waterproofing is completed (see 6.4 regarding the effects of dewatering on nearby structures). On open sites, where any adjacent structures are sufficiently remote to be unaffected by groundwater lowering, dewatering or pumping from carefully arranged sumps with appropriate drainage channels should be continuous while the laying of any waterproofing barrier materials is in progress and until all loading coats have hardened and the structure has developed sufficient strength to resist the full water pressure. 7.2 Structural Elements Forms of construction to receive below ground waterproofing protection may include the following: a) Walls constructed from: 1) masonry (plain or reinforced brick or block); 2) precast concrete; 3) in-situ concrete, either cast in form (plain, reinforced or prestressed) or embedded walls; or 4) steel or concrete piles in embedded walls. b) Base slab constructed from concrete cast in situ, plain or reinforced, raft or other form. c) Roof, where applicable constructed from reinforced in-situ concrete, precast concrete with an in-situ topping, or a steel composite slab, as appropriate. NOTES 1 For structures cast entirely below ground, or where the substructure extends beyond the superstructure, the roof slab requires protection against water ingress (see 6.2.1). 2 Further guidance on construction methods for each type of waterproofing protection is given in 8, 9 and TYPE A (BARRIER) PROTECTION 8.1 Structural Aspects Structures using Type A protection are normally constructed of concrete or masonry. Deeper structures are of concrete construction. Steel can also form part of the construction as temporary sheet piling. Consideration might be given to employing the sheet pile wall as an element of the waterproofing system 15 (see 9). Schematic illustrations of Type A protection are given in Fig. 2(a) General Barrier protection design should be based on an evaluation of: a) the nature of the substrate(s); b) the likely overall and local movements that might cause distress in the waterproofing barrier; c) the ability of the barrier system to accommodate these movements; d) the essential characteristics of the waterproofing system, e.g. bonded/unbonded, pre-applied/postapplied, liquid-applied or pre-formed; e) the need for external or internal application; and f) the effects of environmental contaminants Differential Movement and Cracking Barrier-specific properties should also be evaluated, allowing for any predicted cracking from the structure. The waterproofing barrier should be capable of providing the appropriate protection against water and water vapour without disruption or decay. Although some barrier materials accept local strains and can accommodate a crack opening in the supporting structure, it should be noted that others might be damaged by differential movement or cracking (see Fig. 4). Care should be taken so that a load-bearing substrate is capable of supporting the barrier material, even under sustained water pressure, particularly around openings or service penetrations. A levelling or smoothing layer should be applied to masonry structures, as required. NOTE There are two issues in regard to the possible influence of cracks on barrier performance. One relates to cracks pre-existing at the time of application and the ability of the selected system to initially bridge the crack. Decisions based on the specific properties of the barrier material would be needed before deciding whether any such cracks require pre-treatment. The second issue is the ability of the selected system to accommodate cracks that might form after application. Remedial measures to fill significant voids or openings should be undertaken as the effect of sustained water pressure forcing the barrier material into them might create a risk of failure Continuity of Waterproofing Barrier The waterproofing barrier should, in most instances, be continuous around the structure (see 6.2.4). In order to maintain the continuity of the barrier, penetrations through walls or floors that are to be protected (e.g. openings for services, pipes, cables) should be avoided, wherever possible. Where it is

17 essential to provide such openings, special treatment around the penetration should be provided and reference should be made to the manufacturer s instructions and specialist advice. Similarly, where fixings through the barrier are necessary, the manufacturer s instructions should be followed. Movement joints below ground should not be used unless unavoidable; in such cases these should be waterproofed in accordance with the manufacturer s instructions. Where a waterproofing barrier is required for a structure supported on piled foundations, special consideration should be given to the detailing so that structural continuity is not compromised (see Fig. 5) and reference should be made to the manufacturer s instructions. 8.2 Waterproofing Barrier Materials General The waterproofing barrier used to provide Type A protection should be installed in one of the following locations, depending on the material(s) from which it is formed: a) On the exterior face of walls or slabs (external waterproofing); b) On some external source of support (reverse waterproofing); c) Within the structure (sandwiched waterproofing); d) On the interior face of perimeter walls (internal waterproofing). (a) Reinforced (in-situ concrete/ masonry wall) (b) Unreinforced or nominally reinforced (in-situ concrete/masonry wall) Key 1 Stress and crack width reduced by reinforcement 2 Likely to be compatible with most waterproofing barriers 3 Stress and crack width increased by lack of reinforcement 4 Might exceed strain capacity of some water proofing barriers if wall cracks FIG. 4 EFFECT OF STRUCTURE ON APPLIED WATERPROOFING BARRIER Key 1 Floor slab 2 Pile cap, as appropriate 3 Pile 4 Pile reinforcement 5 Slab/pile/pile cap to have integral protection and/or added internal or external membrane (catering for reinforcement, see 8.1.3) FIG. 5 PILE TO FLOOR SLAB JUNCTION 16

18 Table 3 should be considered when selecting the appropriate waterproofing barrier for use. All barriers should be installed strictly in accordance with the manufacturer s instructions, including any recommendations regarding: 1) protection from damage, following application and curing, where the barrier is applied externally; 2) penetrations through the barrier; 3) fixings, where these are necessary; 4) application over joints in the substrate. Table 3 Categories of barrier materials (Clause 8.2.1) Type of barrier Description Application* (1) (2) (3) Pre-applied composite sheet membranes Applied before concreting of structural slabs Comprising HDPE based carrier film, synthetic and confined walls. Can be applied externally adhesives and protective layer that bond to or sandwiched. concrete poured against them. Bonded sheet membranes (see 8.2.2) Unbonded sheet membranes (see 8.2.3) Liquid applied membranes (see 8.2.4) Geosynthetic clay liners (see 8.2.5) Cementitious crystallization slurries and powders (see 8.2.6) Cementitious multi coat renders, topping and coatings (see 8.2.7) Synthetic or Bitumen based sheet membrane can be either: a) Flexible, cold applied (self adhesive); or b) Hot applied (torch-on or bonded using a hot melt bitumen adhesive) gnereally applied in multiple layers Flexible, synthetic sheet co-extruded membranes generally made of plasticized PVC with a signal layer in case of damage There are many types of liquid applied membranes, which included one or two part systems. These comprise Bentonite with a single or dual carrier material, typically of Geotextile or HDPE. There are two principal forms; dry Bentonite and pre hydrated Bentonite. These are applied as coating to surface of concrete walls and slabs or a solution or powder added to concrete. These are generally applied in multicoats or slurries and are resistant to liquid water but allow some water vapor penetration. Can be applied externally or sandwiched. Does not provide bonded membrane protection below slabs. Can be applied externally or sandwiched. Requires separation layers and protection screed below slab. Can be applied externally or sandwiched Can be applied externally or sandwiched. Vulnerable to wet/dry cycling and must remain confined to be watertight. Can be applied internally or externally. Can be applied internally or externally * see fig. 2 and 6. 17

19 Key 1 Bonded barrier preventing water from tracking from a defect in the membrane to a crack/joint in the supporting concrete wall NOTE if the defect is coincident with a crack, the crack can be repaired with crack injection. 2 Partially bonded or Unbonded barrier allowing water to track from a defect 3 Defect in barrier FIG. 6 EFFECT OF BONDED AND UNBONDED BARRIERS Bonded Sheet Membranes Bonded sheet membranes may be pre- or post-applied to the structure. Pre-applied membranes are initially attached to enabling works in a reverse waterproofing application; they subsequently become bonded to poured concrete walls and slabs using synthetic adhesive layers General A bonded sheet membrane should be firmly supported by a load bearing structure so that external ground and water pressures are adequately resisted. It is important that the substructure provides a satisfactory base on which to apply the membrane, and therefore concrete should be free from ridges and indentions and finished to a true and even surface, preferably with a wood float finish. Brickwork and block work should have flush joints. In all cases the manufacturer s instructions shall be closely followed regarding, substrate preparation, detailing and lap sealing. For hot applied materials, care needs to be taken to ensure the adhesive is melted for the whole area to avoid only partial bonding of the membrane and associated risks of water tracking (see Fig. 6). Cold applied materials are increasingly preferred due to ease of installation and to avoid the high risk of fire and injury Horizontal applications Membrane applications below foundations slabs are all effectively reverse waterproofing applications and should therefore use only a pre-applied bonded membrane slab (see Fig. 6b). Protective screeds, fabrics or boards should be avoided as they act as a de-bonding layer between the membrane and structural concrete and provide a path for water migration Vertical applications (pre-applied) For protection of walls on confined sites against temporary works or piled walls, a pre-applied membrane that subsequently becomes bonded to the poured concrete should be mechanically fixed to the vertical substrate to provide a fully bonded application Vertical applications (post-applied) For walls with external working space that allows the waterproofing to be applied after the concrete wall is poured, post-applied self adhesive membranes shall be used. Walls shall be prepared in accordance with membrane manufacturer s instructions. Careful attention needs to be paid to the compatibility and sealing of the junction between the exposed external face of the pre-applied slab membrane and the post-applied membrane Unbonded Sheet Membranes General Generally made from plasticised PVC to a minimum of 2 mm thick, sheets are co-extruded in two colours to provide a signal layer to show damage for visual inspection. As the membrane is unbonded utmost care should be taken to avoid any damage. All substrates should be as smooth as possible, free from debris, and other irregularities that may puncture the waterproofing layers Horizontal applications The membrane is loose laid sandwiched between layers of geotextile; the first layer is an adjustment layer to compensate for surface irregularities, the second is a separation layer from subsequent minimum 50 mm screed protection. The engineer should note that on piled foundations, the unbonded membrane is separated from the structure and will fall

20 away in case of ground settlement leaving the membrane unsupported against water pressure Vertical applications For walls the same sandwich layers are required. The membrane must be attached to the walls using mechanical fixings recommended by the manufacture to which the membrane can be spot welded. Protection to be provided by boards or masonry walls Lap seam welding For all applications, watertightness of unbonded membranes relies totally on lap seam welding. Adjacent membranes are joined together using specialist equipment to provide a double seam weld that allows pressure testing of joints. The pressure testing is to check the integrity of the welds for watertightness and strength and must be completed before subsequent layers are applied Compartmenting To prevent water tracking as described in Fig. 6, unbonded membranes require a compartmenting system to enable the membrane to be divided into sectors and limit the free movement of water ingress around the structure. This is achieved using waterstops profiles of the same material double welded to the waterproof layer. These welds should also be pressure tested for integrity. Future repair operations can be carried out by injection of water reactive resins. For these repairs to be effective and the source of leaks readily identified, compartment sizes should be limited to no more than 150 m Liquid Applied Membranes General Details on the preparation of the substrate, application rate, method and curing requirements should be sought from the manufacturer. Liquid membrane (such as in IS 12027) performance is dependent on the applied thickness and correct mixing of components. Particular attention should therefore be paid to site quality control of mixing and application, both wet and dry film thicknesses to avoid thin patches and unmixed material Sandwich applications When applied to the internal face of the structure, the membrane might need to be restrained against the effects of water pressure; in such cases, the restraining element should be firm against the applied liquid membrane. Suitable protection to the membrane should be provided Geosynthetic Clay Liners Bentonite is a natural clay mineral, which has the capacity to expand when in contact with water forming a barrier to the transmission of water and other liquids. Bentonite is held between two geosynthetic layers. The bentonite forms an impervious seal providing it remains hydrated and fully confined. The geosynthetic layers attach to the poured concrete. Geosynthetic clay liners are available in two forms. Dry bentonite liners rely on activation taking place on site from the absorption of the groundwater once installed. Pre-hydrated bentonite liners are manufactured by vacuum extrusion and do not need to be hydrated on site General Bentonite-based waterproofing should only be used where the liner remains confined between two surfaces. For this reason, bentonite membranes are generally not suitable for use below slabs where ground settlement is likely, e.g. on piled foundations. NOTE The materials are suitable for new-build and refurbishment applications Horizontal applications - Geosynthetic clay liners can be laid onto compacted sub-base or blinding concrete. The surface can be damp, but the liner should not be laid into standing water and should be protected from wet weather to avoid premature hydration. Prematurely hydrated material should be replaced prior to concreting. The manufacturer s advice should be sought on surface preparation requirements. The manufacturer should also be consulted regarding the continuity of the horizontal liner with the vertical liner as different options exist depending on the type of vertical application, i.e. pre-applied (see ) or post-applied (see ) Vertical applications (pre-applied) When pre-applied, the liner should be fixed to formwork or to secant, contiguous or steel piles or diaphragm walls and the concrete should be poured directly, confining the liner Vertical applications (post-applied) When post-applied, the liner should be nailed to the reinforced concrete structure. Minimal substrate preparation is required. As the waterproofing performance relies on full confinement for the life of the structure, as soon as possible after the vertical bentonite sheeting has been applied to the walls, backfilling should take place in accordance with the manufacturer s instructions and to avoid the risk of premature hydration.