FDC Hardware Product Family

Transcription

1 FDC Hardware Product Family

2 Introduction Corning Cable Systems designed the original FDC product family to organize and manage high fiber count cross-connect and interconnect installations, primarily in rack-mount environments. For years, the FDC product family has been used in central office, headend, and private network installations throughout the telecommunications industry, allowing customers to have a versatile, modular fiber management system. Known for its wide range of termination options, ease of installation, pre-connectorized housings, and variety of equipment racks and rack components, the FDC product family has long been considered the pioneer product in Corning Cable Systems development of expertly designed distribution frames and interconnect hardware. Today s FDC Product Family Today s FDC product family incorporates design features that allow the product to better accommodate the changing requirements and growing needs of today s fiber optic networks. The FDC family of products includes three types of housings: connector housings that accommodate a wide range of termination options, splice housings that enable on-the-rack splicing, and FDC units that combine connector and splice housings in a single unit. The FDC product line also offers network bays, frame components, and accessories, allowing a complete package tailored to the needs of your installation. By improving on the original design, yet retaining features that will allow total compatibility with the old design, the FDC product family continues to set the standard for the future of interconnect hardware. When you select Corning Cable Systems, you can be assured of our commitment to quality products as well as prompt, courteous customer service and expert technical support. For all your fiber optic needs, please call Corning Cable Systems at Table of Contents FDC Units, Housings, and Other Components...1 FDC Units...2 Connector Housings...4 Connector Panels and Modules...7 Coupler Products...11 Splice Housings...12 Stubbed Housings...14 Pigtailed and Stubbed Housings and Panels...17 Frames and Components...18 Distribution Bays: Corning Cable Systems FDF and UDF...19 Frame Components...21 FDC System Examples...29 FDC Product Family Part Number Index...31 ICH100

3 FDC Product Specifications FDC Units, Housings, and Other Components The FDC-CMH provides interconnect or cross-connect capabilities between cables and opto-electronics. Each connector housing can be rack-mounted and is available in 24-, 72-, and 96-fiber capacities. (Page 4) FDC units combine the benefits of connector housings and splice housings into single units. These units use standard FDC panels and modules and are available in 24-, 72-, and 144- fiber capacities. (FDC-001 pictured, Page 2) FDC units, connector housings, and splice housings are housed within the FDF distribution bay. Photo ICH89 ICH93 ICH92 ICH94 ICH91 All FDC units, connector housings, and splice housings feature removable hinged front and rear doors for easy access. (Rear view of FDC-CMH pictured, Page 4) The FDC-SMH provides storage and protection of fiber splices in individually accessible trays. (Page 12) 1

4 FDC Product Specifications: FDC Units, Housings, and Other Components FDC Units Description Corning Cable Systems product line of FDC units is a family of housings combined for the splicing and termination of fiber optic cable. Designed to support both cross-connect and interconnect architectures, FDC units can be used in a wiring center as an interface to transmission equipment or in dedicated fiber frames where test access and reconfiguration are key requirements. FDC units combine the benefits of connector housings and splice housings into single units. These units use standard FDC panels and modules and are available in 24-, 72-, and 144-fiber capacities. FDC units are compact and modular, providing ample termination and splice storage capabilities. To improve quality and reduce installation time of these FDC units, Corning Cable Systems recommends factory-pigtailed connector panels or modules. Both are available with a variety of connector types and come complete with factory-installed and tested connectorized pigtails. These pigtailed units are ideal for use in FDC units to speed the termination of fiber cable and provide the consistent quality performance of factory-installed and polished connectors. ZA-1625 Features / Benefits Available with panels or modules equipped with preconnectorized fiber pigtails Available with all common industry connectors Supports single-fiber fusion, mass fusion, and mechanical splices Mountable on standard 19-in (48 cm) or 23-in (58.5 cm) equipment rack or on wall Frontal projection of 4.25-in (10.8 cm) or flush-mounted in an equipment rack when flush-mount accessory kit is used Optional Universal Cable Clamp (FDC-UCC) for additional, enhanced cable strain-relief Removable hinged front and rear doors Front and rear door slide latches for easier access Flipcard for easier record keeping Larger routing guides for better jumper management More open design for easier connector access Improved slide mechanism on splice housings ZA-1626 FDC-001 equipped with optional 6-fiber SC panels FDC-002 equipped with optional 6-fiber SC panels ZA-2138 ZA-2139 FDC-005 equipped with optional 6-fiber SC panels FDC-003 equipped with optional 6-fiber SC panels 2

5 FDC Product Specifications: FDC Units, Housings, and Other Components FDC Units Ordering Information FDC Units Part Dimensions (H x W x D) Shipping Weight Number Description in (cm) lb (kg) FDC-001 FDC Unit with capacity for (24) 6-in panels or modules and 26.5 x 17.0 x (22) 0.2-in tall (Type 2R, 2S) splice trays (144-fiber capacity (66.7 x 43.2 x 27.9) (19.0) when used with 6-fiber panels) FDC-001-F FDC Unit with capacity for (24) 6-in panels or modules and 26.5 x 17.0 x (14) 0.4-in tall (Type 4R, 4S, 4A) splice trays (144-fiber capacity (66.7 x 43.2 x 27.9) (19.0) when used with 6-fiber panels) FDC-002 FDC Unit with capacity for (12) 6-in panels or modules and 17.5 x 17.0 x (22) 0.2-in tall (Type 2R, 2S) splice trays (144-fiber capacity (44.5 x 43.2 x 27.9) (13.2) when used with 6-fiber panels) FDC-002-F FDC Unit with capacity for (12) 6-in panels or modules and 17.5 x 17.0 x (14) 0.4-in tall (Type 4R, 4S, 4A) splice trays (144-fiber capacity (44.5 x 43.2 x 27.9) (13.2) when used with 6-fiber panels) FDC-003 FDC Unit with capacity for (4) 6-in panels or modules and 8.75 x 17.0 x (12) 0.2-in tall (Type 2R, 2S) splice trays (144-fiber capacity (22.2 x 43.2 x 27.9) (7.7) when used with 6-fiber panels) FDC-003-F FDC Unit with capacity for (4) 6-in panels or modules and 8.75 x 17.0 x (7) 0.4-in tall (Type 4R, 4S, 4A) splice trays (144-fiber capacity (22.2 x 43.2 x 27.9) (7.7) when used with 6-fiber panels) FDC-005 FDC Unit with capacity for (4) 6-in panels or modules and 5.25 x 17.0 x (2) 0.2-in tall (Type 2R, 2S) splice trays (144-fiber capacity (13.3 x 43.2 x 27.9) (6.4) when used with 6-fiber panels) FDC-005-F FDC Unit with capacity for (4) 6-in panels or modules and 5.25 x 17.0 x (2) 0.4-in tall (Type 4R, 4S, 4A) splice trays (144-fiber capacity (13.3 x 43.2 x 27.9) (6.4) when used with 6-fiber panels) Note: Connector panels, modules, splice trays, and other accessories must be ordered separately. 3

6 FDC Product Specifications: FDC Units, Housings, and Other Components Connector Housings Description Corning Cable Systems Connector Housings provide interconnect or cross-connect capabilities between the outside plant (OSP), riser, or distribution cables and the opto-electronics. The connector housings can be rack-mounted in standard 19-in (48 cm) or 23-in (58.4 cm) equipment racks and are available in a variety of fiber capacities. Connector housings can be ordered with connector panels or preterminated panels or modules for both multimode and single-mode applications. Labels are provided for documentation and units can be added as needed to construct a fiber distribution frame for high fiber count applications. ZA-1619 Features / Benefits Ideal for field-connectorization Suitable for loose tube, tight-buffered, and ribbon cables Frontal projection of 4.25-in (10.8 cm) or flush-mounted with an optional kit Single cabinet construction Smoke-tinted front door Accepts Corning Cable Systems FDC connector panels, jumper storage modules, and connector modules Removable hinged front and rear doors Front and rear door slide latches for easier access Removable flipcard for easier record keeping Larger routing guides for better jumper management Open design for easier connector access FDC-CMH-072 equipped with optional 6-fiber SC panels FDC-CMH-096 equipped with optional 8-fiber SC panels ZA

7 FDC Product Specifications: FDC Units, Housings, and Other Components Connector Housings Ordering Information Connector Housings - Empty Part Dimensions (H x W x D) Shipping Weight Number Description in (cm) lb (kg) FDC-CMH-024 FDC connector housing; accepts (4) 6-in 5.25 x 17.0 x panels, modules, or jumper storage modules (13.3 x 43.2 x 27.9) (6.3) FDC-CMH-072* FDC connector housing; accepts (12) 6-in 8.75 x 17.0 x panels, modules, or 24 jumper storage modules (22.2 x 43.2 x 27.9) (6.8) FDC-CMH-096 FDC connector housing; accepts (12) 7.5-in 8.75 x 17.0 x panels (FDC-CP8P) or modules (FDC-CP18) only (22.2 x 43.2 x 27.9) (6.8) Note: The FDC-CMH-072 may be configured for 144 fibers using 12-fiber FDC panels with SC adapters. Connector Housings - with Adapters Part Number FDC - CMH Description 72-fiber capacity FDC housing (FDC-CMH-072) with (12) 6-fiber panels equipped with specified adapter type FDC - CMH FDC - CMH - E fiber capacity FDC housing (FDC-CMH-096) with (12) 8-fiber panels equipped with specified adapter type 144-fiber capacity FDC housing (FDC-CMH-072) with (12) 12-fiber panels (available with SC adapter types only) 1 Select adapters. ST Compatible 15 = ST compatible, ceramic insert, multimode, composite housing 15T = ST compatible, ceramic insert, multimode, composite housing, threaded bulkhead mount 19 = ST compatible, ceramic insert, single-mode, composite housing 19T = ST compatible, ceramic insert, single-mode, composite housing, threaded bulkhead mount 25 = ST compatible, composite insert, multimode, composite housing 25T = ST compatible, composite insert, multimode, composite housing, threaded bulkhead mount FC 11 = FC, phosphor bronze insert, multimode or single-mode, metal housing 21 = FC for Angled Polish Connectors (APC), phosphor bronze insert, single-mode, metal housing D4 13 = D4, phosphor bronze insert, multimode or single-mode, metal housing ESCON Compatible 27 = ESCON Compatible/ST Compatible, ceramic insert, composite housing SC 38 = SC, phosphor bronze insert, single-mode 3C = SC, ceramic insert, single-mode 39 = SC, phosphor bronze insert, multimode 56 = SC, composite insert, multimode 6C = SC, for Angled Polish Connectors (APC), ceramic insert, single-mode SC Duplex 57 = 568SC (SC duplex), phosphor bronze insert, multimode, plastic housing 59 = 568SC (SC duplex), ceramic insert, single-mode, plastic housing 91 = 568SC (SC duplex), composite insert, multimode, plastic housing FDDI 33- = FDDI/ST compatible, ceramic insert, composite housing 33P- = FDDI/ST compatible, composite insert, composite housing ( = A, B, M, or S keying option) 3333 = FDDI Duplex-to-Duplex adapters MT-RJ 97 = MT-RJ multimode 98 = MT-RJ single-mode SC-DC 96 = SC-DC multimode 99 = SC-DC single-mode 5

8 FDC Product Specifications: FDC Units, Housings, and Other Components Connector Housings Ordering Information Accessories Jumper Storage Modules Part Number FDC-JSM FDC-JSH-24 Other Accessories Part Number FDC-UCC Description Set of 2 jumper storage modules to fit FDC-CMH-072 or FDC-CMH-024 (each set of two fills the space of one connector panel or module); 5-meter slack capacity per module 8.75-in (22.2 cm) tall jumper storage housing; includes 24 individual jumper storage modules; 5-meter slack capacity per module Description Universal Cable Clamp Kit with FDC mounting bracket FDC-CMH-WALLBKT Wall-mount Bracket for 8.75-in housing FD5-WALLBKT FDC-FLSHMNT-LG FDC-FLSHMNT-SM FDC-CABLE-GRND FDC-PNL-KIT FDC-SIDEPNL-SM FDC-SIDEPNL-LG FDC-FRTDR-LX-L FDC-FRTDR-MT-L Wall-mount Bracket for 5.25-in housing Flush-mount Panels for 8.75-in housing Flush-mount Panels for 5.25-in housing Ground Strap and Clip Kit for -072 to -096 conversion Side Panel Kit for 5.25-in housing Side Panel Kit for 8.75-in housing Front Door with Lock Kit, plastic door, for 8.75-in tall housings Front Door with Lock Kit, metal door, for 8.75-in tall housings ZA-1643 ZA-1651 FDC-JSM FDC-JSH-24 6

9 FDC Product Specifications: FDC Units, Housings, and Other Components Connector Panels and Modules Description ZA-1621 ZA-1622 ZA-2096 Corning Cable Systems offers a variety of panels and modules for use in the FDC family of products. The panels are used with field-installable connectors or in applications where the preconnectorized cables are routed directly to the FDC housing. Both the panels and the modules may be equipped with 900 µm single-fiber or ribbon-fiber pigtails for pigtail splicing. Panels and modules are available with a variety of connector types. Plastic modules include molded-in areas for coiling fiber slack and protecting the minimum bend radius of the fiber. Features / Benefits Made of injection-molded plastic or sheet metal Modules accommodate various fiber types Accommodates most standard connector types Unique connector adapters enable easy connector access Fiber routing and bend radius protection designed into each module FDC-CP1P-38 FDC-CP8P-38 FDC-CP1P-1238 Connector Panels ZA-2143 ZA-1644 ZA-1645 OPEN CLOSE FDC-CP16-58 FDC-CM12-58 Connector Modules FDC-CP

10 FDC Product Specifications: FDC Units, Housings, and Other Components Connector Panels and Modules Ordering Information Empty Connector Panels Part Number Description FDC-BLANK Blank connector panel for FDC-CMH-072 or FDC-CMH-024 housings FDC-CP0P Connector panel accepts up to 6 ST compatible, D4, Biconic, or FC adapters FDC-CP0P-25T Connector panel accepts up to 6 threaded ST compatible adapters FDC-CP0P-33 Connector panel accepts up to 3 FDDI/ST compatible Duplex-to-Simplex adapters FDC-CP0P-38 Connector panel accepts up to 6 SC adapters FDC-CP0P-3333 Connector panel accepts up to 3 FDDI Duplex-to-Duplex adapters FDC-CP0P-57 Connector panel accepts up to 3 Duplex SC adapters FDC-CP8P Connector panel accepts up to 8 ST compatible, D4, Biconic, or FC adapters FDC-CP8P-ST Connector panel accepts up to 8 threaded ST compatible adapters Empty Modules Part Number FDC-CP0 FDC-CP8 FDC-CM0 Description Empty 6-position module (with universal adapters) Empty 8-position module (with universal adapters) Empty 12-position module (with universal adapters) 8

11 FDC Product Specifications: FDC Units, Housings, and Other Components Connector Panels and Modules Ordering Information Connector Panels - with Adapters Part Number Description FDC - CP1P - 6-in FDC connector panel with (6) factory-installed adapters 1 FDC - CP8P - 1 FDC - CP1P FDC - CP1P in FDC connector panel with (8) factory-installed adapters Note: The 7.5-in FDC connector panels are only compatible with the FDC-CMH in FDC connector panel with (12) factory-installed adapters (available with SC adapter types only) 6-in FDC connector panel with (6) factory-installed adapters (available with SC adapter types only) 1 Select adapters. ESCON Compatible ST Compatible 15 = ST compatible, ceramic insert, multimode, composite housing 15T = ST compatible, ceramic insert, multimode, composite housing, threaded bulkhead mount 19 = ST compatible, ceramic insert, single-mode, composite housing 19T = ST compatible, ceramic insert, single-mode, composite housing, threaded bulkhead mount 25 = ST compatible, composite insert, multimode, composite housing 25T = ST compatible, composite insert, multimode, composite housing, threaded bulkhead mount FC 11 = FC, phosphor bronze insert, multimode or single-mode, metal housing 21 = FC for Angled Polish Connectors (APC), phosphor bronze insert, single-mode, metal housing D4 13 = D4, phosphor bronze insert, multimode or single-mode, 33P- = metal housing 27 = ESCON Compatible/ST Compatible, ceramic insert, composite housing SC 38 = SC, phosphor bronze insert, single-mode 3C = SC, ceramic insert, single-mode 39 = SC, phosphor bronze insert, multimode 56 = SC, composite insert, multimode 6C = SC, for Angled Polish Connectors (APC), ceramic insert, single-mode Duplex SC 57 = 568SC (Duplex SC), phosphor bronze insert, multimode, plastic housing 59 = 568SC (Duplex SC), ceramic insert, single-mode, plastic housing 91 = 568SC (Duplex SC), composite insert, multimode, plastic housing FDDI 33- = FDDI/ST compatible, ceramic insert, composite housing FDDI/ST compatible, composite insert, composite housing ( = A, B, M, or S keying option) 3333 = FDDI Duplex-to-Duplex adapters Connector Panels - with MT-RJ and SC-DC Adapters Part Number Description FDC - CP1P - 6-in FDC connector panel with MT-RJ or SC-DC adapters installed 1 2 FDC - CP8P in FDC connector panel with MT-RJ or SC-DC adapters installed Note: The 7.5-in FDC connector panels are only compatible with the FDC-CMH Select number of terminations per panel. 06 = Panel with 3 MT-RJ or SC-DC installed 08 = Panel with 4 MT-RJ or SC-DC installed 12 = Panel with 6 MT-RJ or SC-DC installed 16 = Panel with 8 MT-RJ or SC-DC installed 24 = Panel with 12 MT-RJ or SC-DC installed 2 Select adapters. MT-RJ SC-DC 97 = MT-RJ multimode 96 = SC-DC multimode 98 = MT-RJ single-mode 99 = SC-DC single-mode 9

12 FDC Product Specifications: FDC Units, Housings, and Other Components Connector Panels and Modules Ordering Information Pigtailed Panels and Modules Part Number Description FDC - CP1P in FDC connector panel with six 900 µm MIC fiber pigtails 1 3 FDC - RF12 - Two 6-in FDC connector panels with one 12-fiber ribbon pigtail 1 FDC - CP FDC - CP FDC - CM FDC - AC12-6-in FDC module with (6) single-fiber pigtails 7.5-in FDC module with (8) single-fiber pigtails* 6-in FDC module with (12) single-fiber pigtails; double-width module 6-in FDC module with 12-fiber ribbon pigtails; double-width module Note: * Fits FDC-CMH-096 only. 1 1 Select connector code. Single-mode, Ultra PC (RFL -55 db): 58 = SC/UPC, metal insert adapter 5C = SC/UPC, ceramic insert adapter 72 = SC/UPC, duplex, ceramic insert adapter 54 = FC/UPC, metal insert adapter 61 = ST compatible/upc, ceramic insert adapter 6T = ST compatible/upc, threaded, ceramic insert adapter 62 = D4/UPC, metal insert adapter Single-mode, Hyper PC (RFL -60 db): 76 = FC/HPC, metal insert adapter 77 = SC/HPC, metal insert adapter 7C = SC/HPC, ceramic insert adapter 78 = D4/UPC, metal insert adapter 79 = ST compatible/hpc, ceramic insert adapter Single-mode, Angled PC (RFL -65 db): 6C = SC/APC, ceramic insert adapter 21 = FC/APC, metal insert adapter Multimode 39 = SC, metal insert adapter 56 = SC, composite insert adapter 25 = ST compatible, composite insert adapter 50 = ST compatible, ceramic insert adapter 17 = FC, metal insert adapter 91 = SC, Duplex, composite insert adapter 53 = ESCON/ST compatible, ceramic insert adapter MT-RJ 97 = MT-RJ multimode 98 = MT-RJ single-mode SC-DC 96 = SC-DC multimode 99 = SC-DC single-mode 2 Select fiber core size. 3 Select connector type. Multimode 050 = 50 µm 063 = 62.5 µm Single-mode Leave blank. SC = SC ST = ST compatible FC = FC D4 = D4 Note: Connector type and connector code in Option should be compatible. 1 10

13 FDC Product Specifications: FDC Units, Housings, and Other Components Coupler Products Corning Cable Systems offers the FDC and FD8 Coupler Modules and the High-Density Coupler Shelf to accommodate couplers/splitters and WDMs in the FDC System. Coupler Modules Corning Cable Systems offers two coupler module styles for use with the FDC product family. Up to twelve FDC coupler modules are accommodated in each FDC-CMH-072 Connector Module Housing. Six-inch format coupler modules can also be installed in other housings designed to accept FDC connector modules. The FDC-CMH-096 will house up to twelve 7.5-in format FDC coupler modules (FD8). Corning Cable Systems FDC Coupler Modules provide a modular way to install and maintain optical networks with coupler or WDM requirements. Each module can be configured with any combination of adapter or pigtail inputs and outputs and a variety of connector options. Coupler Shelves For larger coupler designs, Corning Cable Systems offers the FDC High-Density Coupler Shelf. The single rack-height shelf provides up to 22 adapter or pigtail inputs and outputs. Similarly, the double-high (two-rack space) shelf provides 44 adapter or pigtail inputs and outputs. Both shelves are 19-inch and 23-inch rack-mountable and feature a slide-forward design for easy access to optical jumpers and pigtails. Coupler Modules (FDC, FD8) High-Density Coupler Shelf with SC Adapters ZA-2140 ZA-2153 Ordering Information* Part Number Example: FDC-23K-K-58 Description FDC Coupler Module with two 50/50 1 x 2 couplers and SC Ultra PC terminations * For a complete listing of available module configuratons, refer to Corning Cable Systems Passive Optical Devices Ordering Guide, ICH-135A. Specifications Description Dimensions (H x W x D) Shipping Weight in (cm) lb (kg) FDC Coupler Module (FDC) 4 x 1.5 x 7 (10.2 x 3.8 x 17.8) 1 (0.45) FDB Coupler Module (FDB) 4 x 3.0 x 7 (10.2 x 7.6 x 17.8) 1.6 (0.73) High-Density Shelf (HSF) 1.7 x 20.3 x 12 (4.3 x 30.5 x 51.6) 3.8 (1.7) 11

14 FDC Product Specifications: FDC Units, Housings, and Other Components Splice Housings Description The Corning Cable Systems FDC-SMH-3 and FDC-SMH-5 Splice Housings provide storage and protection of fiber splices in individually accessible trays. The housings can be mated with other FDC connector housings for pigtail splicing or can be used individually as a rack-mounted splice housing. The units accommodate a wide variety of Corning Cable Systems splice trays. ZA-1624 Features / Benefits Rack-mountable on standard 19-in (48 cm) or 23-in (58.5 cm) equipment rack; wall-mountable option Single-cabinet construction Suitable for loose tube, tight-buffered, and ribbon cables Slide-out shelf for easy tray access with improved slide mechanism Optional Universal Cable Clamp (FDC-UCC) for additional, enhanced cable strain-relief Hinged front and rear doors Front and rear door slide latches for easier access FDC-SMH-3 ZA-1623 FDC-SMH-5 12

15 FDC Product Specifications: FDC Units, Housings, and Other Components Splice Housings Ordering Information Splice Housings Part Dimensions (H x W x D) Shipping Weight Number Description in (cm) lb (kg) FDC-SMH-3 Splice housing; accepts (8) 0.2-in tall (Type 2R, 2S, 2M) 5.25 x 17.0 x Corning Cable Systems splice trays; 96-fiber 12 splices per tray (13.3 x 43.2 x 28.0) (5.9) FDC-SMH-3-F Splice housing; accepts (5) 0.4-in tall (Type 4R, 4S, 4A) 5.25 x 17.0 x Corning Cable Systems splice trays; 60-fiber 12 splices per tray (13.3 x 43.2 x 28.0) (5.9) FDC-SMH-5 Splice housing; accepts (22) 0.2-in tall (Type 2R, 2S, 2M) 8.75 x 17.0 x Corning Cable Systems splice trays; 264-fiber 12 splices per tray (22.2 x 43.2 x 28.0) (6.4) FDC-SMH-5-F Splice housing; accepts (14) 0.4-in tall (Type 4R, 4S, 4A) 8.75 x 17.0 x Corning Cable Systems splice trays; 168-fiber 12 splices per tray (22.2 x 43.2 x 28.0) (6.4) Note: For higher splice capacity, use 24-fiber splice trays. Splice trays must be ordered separately. Accessories Splice Trays Part Number Description Tray Type M Single-fiber fusion splice tray; 0.2-in (0.51 cm) tall at 12 splices per tray Type 2S M Single-fiber heat-shrink fusion splice tray; 0.2-in (0.51 cm) tall at 12 splices per tray Type 2S M Heat-shrink mass-fusion splice tray; 0.4-in (1.02 cm) tall at 12 splices per tray Type 2R M Single-fiber fusion splice tray; 0.2-in (0.51 cm) tall at 24 splices per tray Type 2S UST-024 Universal 24-fiber splice tray; 0.4-in (1.02 cm) tall Type 4A UST Universal splice tray configured for mass or single-fiber heat-shrink fusion; 0.4-in (1.02 cm) tall Type 4A Note: Other splice trays are also available. 13

16 FDC Product Specifications: FDC Units, Housings, and Other Components Stubbed Housings Description ZA-1646 FDC housings are available with a preconnectorized cable stub made from loose tube, tight-buffered, or ribbon cables. The stubbed option allows the splice point to be located in a splicing vault or at the building entrance point. The cable stub is typically shipped coiled on a reel and strain-relieved where it enters the housing. The factory-connectorized fibers terminate in the rear of the adapters. This complete factory-installed and tested assembly allows for fast, efficient installation of the patch panel and eliminates the need for conduit when stubbed with OFNR cable. This preconnectorized, stubbed housing also conserves rack space and offers the assurance of factoryquality connectors. Partially filled housings can later be completed by ordering a preconnectorized cable installed into modules or panels. These modules will snap into the existing housing to fill vacant positions. FDC Stubbed Connector Housing (FDC-CMH-072) Features / Benefits Fully assembled Fast, efficient installation Use of UL-listed cable eliminates the need for metal conduit Increases available space at the equipment rack by moving splices to a remote location Available with various fiber counts, connector types and cable styles Stubbed connector modules or panels allow incremental growth of housings Options Stubbed FDC housings include: Connector housing Connector panels or modules Adapters Connectorized cable of specified length Stubbed FDC connector panels include: Connector panels Adapters Connectorized cable of specified length Stubbed FDC connector modules include: Connector modules Adapters Connectorized cable of specified length 14

17 FDC Product Specifications: FDC Units, Housings, and Other Components Pigtailed and Stubbed Housings Ordering Information Pigtailed Housings / Panels Stubbed Housings Select housing type. FDC = FDC-CMH-072, Standard FDC unit housing, 72-fiber FD5 = FDC-CMH-024, 24-fiber FD8 = FDC-CMH-096, Medium-density FDC unit, 96-fiber FDM = FDC stubbed 6-fiber modules, housing not included FDP = FDC stubbed 6-fiber panels, housing not included FHC = FDC-CMH-072, with 12-fiber SC panels, 144-fiber FHP = FDC stubbed 12-fiber panels, housing not included F8P = FDC stubbed 8-fiber panels, housing not included Select connector panels or modules. P = Connector panels (standard) M = Connector modules Select number of fibers. (0-99 fibers, enter 2-digit number; 100+, enter alpha numeric from Table A) Examples: 12 = 12-fiber 72 = 72-fiber 96 = 96-fiber E4 = 144-fiber M6 = 216-fiber Select cable length in meters. (1 meter = ft) (0-99 meters, enter 2-digit number; 100+, enter alpha numeric from Table A) Examples: 31 = 31 m (100 ft) A0 = 100 m F5 = 155 m 5 6 Select connector code. Single-mode, Ultra PC (RFL -55 db): 58 = SC/UPC, metal insert adapter 5C = SC/UPC, ceramic insert adapter 72 = SC/UPC Duplex, ceramic insert adapter 54 = FC/UPC, metal insert adapter 61 = ST compatible/upc, ceramic insert adapter 6T = ST compatible/upc, threaded, ceramic insert adapter 62 = D4/UPC, metal insert adapter Single-mode, Hyper PC (RFL -60 db): 76 = FC/HPC, metal insert adapter 77 = SC/HPC, metal insert adapter 7C = SC/HPC, ceramic insert adapter 78 = D4/HPC, metal insert adapter 79 = ST compatible/hpc, ceramic insert adapter Single-mode, Angled PC (RFL -70 db): 6C = SC/APC, ceramic insert adapter 21 = FC/APC, metal insert adapter Multimode: 39 = SC/PC, metal insert adapter 56 = SC/PC, composite insert adapter 50 = ST compatible/pc, ceramic insert adapter 5T = ST compatible/pc, threaded, ceramic insert adapter 25 = ST compatible/pc, composite insert adapter 2T = ST compatible/pc, threaded, composite insert adapter 17 = FC/PC, metal insert adapter 34 = FDDI/ST compatible, ceramic insert adapter 53 = ESCON/ST compatible, ceramic insert adapter 57 = SC Duplex, metal insert adapter 91 = SC Duplex, composite insert adapter Select fiber type. = Single-mode C = Multimode (50/125) K = Multimode (62.5/125) 15

18 FDC Product Specifications: FDC Units, Housings, and Other Components Pigtailed and Stubbed Housings Select cable type. 900 µm Coated Fiber Cables: 81 = TBII MIC Riser Cable 85 = Enhanced OptiStrip MIC Riser Cable 88 = Flexible MIC Plenum Cable 250 µm Coated Fiber Loose Tube Cables: W4 = Outside Plant ALTOS Cable, all-dielectric W5 = Outside Plant ALTOS Cable, single armor W6 = Outside Plant ALTOS Cable, double armor W7 = ALTOS Riser Cable WF = FREEDM Cable, indoor/outdoor WZ = ALTOS LSZH Cable Ribbon Fiber Cables: C4 = Outside Plant SST-Ribbon Cable, all-dielectric C5 = Outside Plant SST-Ribbon Cable, single armor C6 = Outside Plant SST-Ribbon Cable, double armor C7 = Ribbon Riser Cable CF = FREEDM Ribbon Riser Cable, indoor/outdoor Note: Please verify specific cable fiber count availability with a Siecor Customer Service Representative. Select special configuration. 00 = Standard product Select number of cables. 1 = One (default) 2 = Two Select cable entry. (View housing from the front) A = Bottom/Left * B = Top/Right (default for rack-mount) C = Top/Left D = Bottom/Right * * Note: This option not available with the FDC-CMH-024 (FD5). 11 Select pigtail type. P = Enhanced OptiStrip 900 µm fiber R = 12-fiber ribbon Table A Codes for Fiber Counts and Cable Stub Lengths Over 99 A _ = 10_ AN = 460 B _ = 11_ AP = 470 C _ = 12_ AQ = 480 D _ = 13_ AR = 490 E _ = 14_ AS = 500 F _ = 15_ AT = 510 G _ = 16_ AU = 520 H _ = 17_ AV = 530 J _ = 18_ AW = 540 K _ = 19_ AX = 550 L _ = 20_ AY = 560 M_ = 21_ AZ = 570 N _ = 22_ BA = 580 P _ = 23_ BB = 590 Q _ = 24_ BC = 600 R _ = 25_ BD = 610 S _ = 26_ BE = 620 T _ = 27_ BF = 630 U _ = 28_ BG = 640 V _ = 29_ BH = 650 W_ = 30_ BJ = 660 X _ = 31_ BK = 670 Y _ = 32_ BL = 680 Z _ = 33_ BM = 690 AA = 340 BN = 700 AB = 350 BP = 710 AC = 360 BQ = 720 AD = 370 BR = 730 AE = 380 BS = 740 AF = 390 BT = 750 AG = 400 BU = 760 AH = 410 BV = 770 AJ = 420 BW = 780 AK = 430 BX = 790 AL = 440 BY = 800 AM = 450 BZ = 810 I and O are not used. Lengths from 100 to 339, use single letter plus number (1 to 9). Examples: E4 = 144 fiber A5 = 105 m M6 = 216 fiber T9 = 279 m Lengths over 339 m can be ordered in 10 m increments only. Use double letters. 16

19 FDC Product Specifications: FDC Units, Housings, and Other Components Pigtailed and Stubbed Housings and Panels Stubbed Hardware Packaging Information Box Outside Drum Flange Width of Package Additional Total Packaging Dimensions Diameter Height Reel Weight Material Weight Method in in in in lb lb lb H Short Stub (Coiled Cable) 34 x 31 x Q Wheel-a-Reel (Plywood) W CTS Reel (Plywood) Z CTS Reel (Plywood) Maximum Packaged Length in Feet (72-fiber cable / 144-fiber cable / 216-fiber cable) Packaging Ribbon 900 µm OptiStrip ALTOS Outside Plant Method Riser Cable MIC Riser Cable Riser Cable Loose Tube Cable H Short Stub (Coiled Cable) 100 / N/A / N/A 100 / N/A / N/A 100 / N/A / N/A 100 / N/A / N/A Q Wheel-a-Reel (Plywood) 1070 / N/A / N/A 399 / N/A / N/A 864 / 424 / N/A 972 / N/A / N/A W CTS Reel (Plywood) 1892 / 1293 / / 358 / N/A 1528 / 750 / / 898 / 841 Z CTS Reel (Plywood) 4631 / 3165 / / 877 / N/A 3739 / 1835 / / 2198 / 2058 ZA-058a ZA-726 ZA-1411 Wheel-a-Reel Short Stub CTS Reel 17

20 FDC Product Specifications Frames and Components The Fiber Distribution Frame (FDF) distribution bay provides the user with a focal point for fiber optic cable termination and allows easy access to connections for efficient administration of fiber circuits. (Page 18) Photo ICH88 18

21 FDC Product Specifications: Frames and Components Distribution Bays: Corning Cable Systems FDF and UDF Description Features / Benefits Distribution bays offer a means of interconnecting, crossconnecting, and testing fiber optic cables. Distribution bays provide the user with a focal point for fiber optic cable termination and allow easy access to connections for efficient administration of fiber circuits. Corning Cable Systems offers two types of distribution bays: the Fiber Distribution Frame (FDF), and the Unequal Flange Distribution Frame (UDF). Modular design allows a variety of configurations Both the FDF and UDF bays feature an EIA industry standard hole spacing pattern that is compatible with both hardware and most industry-standard electronics Available pre-assembled with connector housings The versatile, modular design of the FDF and the UDF allows interchangeability of connector housings and splice housings within each rack. In addition, the FDF and UDF are both fully compatible with Corning Cable Systems complete line of fiber optic cables and hardware. ZA-1629 ZA-1630 Dual FDF Assembly (Housings and End Caps not included) UDF Assembly (Housings not included) 19

22 FDC Product Specifications: Frames and Components Distribution Bays: Corning Cable Systems FDF and UDF Ordering Information Distribution Bays Part Dimensions (H x W x D) Shipping Weight Number Description Consists of: * Quantity in (cm) lb (kg) FDF Assembled Equal Flange FDF-ER x 24.3 x Bay Configuration FDF-JT-23 3 (213.4 x 61.7 x 30.5) (56.8) (23-in Frame) FDF-RG FDF-B-10 2 FDF-CTB 1 FDF Assembled Equal Flange FDF-ER x 24.3 x Bay Configuration FDF-XT-23 2 (213.4 x 61.7 x 30.5) (70.5) (23-in Frame) FDF-RG FDF-B-10 2 FDF-CTB 1 UDF E-35 Assembled Unequal Flange UDF-ER-7-E x 24.3 x Bay Configuration FDF-JT-23 3 (213.4 x 61.7 x 30.5) (54.4) (23-in Frame) FDF-RG UDF-CTB 1 UDF E-35 Assembled Unequal Flange UDF-ER-7-E x 24.3 x Bay Configuration FDF-XT-23 2 (213.4 x 61.7 x 30.5) (54.4) (23-in Frame) FDF-RG UDF-CTB 1 Bay Assemblies (Assembled bays that include eight FDC-CMH-072 housings - does not not include end caps.) Part Dimensions (H x W x D) Shipping Weight Number Description Consists of: Quantity in (cm) lb (kg) FDF Assembled Equal Flange FDF x 24.3 x Bay and Housings FDC-CMH (213.4 x 61.7 x 30.5) (111.1) FDF Assembled Equal Flange FDF x 24.3 x Bay and Housings FDC-CMH (213.4 x 61.7 x 30.5) (124.7) UDF E-35 Assembled Unequal Flange UDF E x 24.3 x Bay and Housings FDC-CMH (213.4 x 61.7 x 30.5) (108.8) UDF E-35 Assembled Unequal Flange UDF E x 24.3 x Bay and Housings FDC-CMH (213.4 x 61.7 x 30.5) (108.8) * Part Number Reference List Part Number Description Page FDC-CMH-072 FDC Connector Housing 4 FDF-B-10 Foot Cap for FDF Frame 22 FDF-CTB Cable Tie Bracket for FDF Frame 26 FDF-ER-7 7-ft Equal Flange Equipment Rack 20 FDF-JT-23 FDF Jumper Trough; 1.75-in 24 Part Number Description Page FDF-RG-10 FDF Routing Guide 26 FDF-XT-23 FDF Jumper Trough; 3.25-in 24 UDF-CTB Cable Tie Bracket for UDF Frame 26 UDF-ER-7-E-35 7-ft Unequal Flange Equipment Rack 20 20

23 FDC Product Specifications: Frames and Components Frame Components Equipment Racks The backbone of each distribution bay is its equipment rack. Standard 23-in (58.4 cm) equipment racks are available in 7-ft (2.1 m), 9-ft (2.7 m), and 11.5-ft (3.5 m) heights. Racks come in two versions equal flange and unequal flange. Both rack styles feature industry-standard EIA hole spacing. Extensions Frame extensions are used to convert 7-ft equipment racks into 9-ft or 11.5-ft equipment racks. Frame extensions are also available in both equal flange and unequal flange styles. FDF Equipment Rack and Extensions UDF Equipment Rack and Extensions FDF-EXT-7/9 ZA-1627 UDF-EXT-7/9-E-35 ZA-1628 FDF-EXT-7/11 FDF-ER-7 UDF-EXT-7/11-E-35 UDF-ER-7-E-35 21

24 FDC Product Specifications: Frames and Components Frame Components Ordering Information Equipment Racks Part Dimensions (H x W x D) Shipping Weight Number Description in (cm) lb (kg) FDF-ER-7 7-ft Equal Flange Equipment Rack, 23-in; 84.0 x 24.3 x does not include foot caps (213.4 x 61.7 x 30.5) (22.6) FDF-ER ft Equal Flange Equipment Rack, 19-in; 84.0 x 21.9 x does not include foot caps (213.4 x 55.6 x 30.5) (22.6) FDF-ER-9 9-ft Equal Flange Equipment Rack, 23-in; x 24.3 x does not include foot caps (7-ft rack plus 2-ft extension) (274.3 x 61.7 x 30.5) (24.9) FDF-ER ft Equal Flange Equipment Rack, 23-in; x 24.3 x does not include foot caps (7-ft rack plus 4.5-ft extension) (335.3 x 61.7 x 30.5) (27.2) UDF-ER-7-E-35 7-ft Unequal Flange Equipment Rack, 23-in 84.0 x 25.9 x (213.4 x 65.8 x 25.7) (22.6) UDF-ER-7-19-E-35 7-ft Unequal Flange Equipment Rack, 19-in 84.0 x 21.9 x (213.4 x 55.6 x 25.7) (22.6) UDF-ER-9-E-35 9-ft Unequal Flange Equipment Rack, 23-in x 25.9 x (7-ft rack plus 2-ft extension) (274.3 x 65.8 x 25.7) (24.9) UDF-ER-11-E ft Unequal Flange Equipment Rack, 23-in x 25.9 x (7-ft rack plus 4.5-ft extension) (335.3 x 65.8 x 25.7) (27.2) Extensions Part Dimensions (H x W x D) Shipping Weight Number Description in (cm) lb (kg) FDF-EXT-7/9 2-ft Rack Extension; for use with equal flange rack 24.0 x 24.3 x (FDF-ER-7) (60.9 x 61.7 x 30.5) (6.8) FDF-EXT-7/ ft Rack Extension; for use with equal flange rack 54.0 x 24.3 x (FDF-ER-7) (137.0 x 61.7 x 30.5) (12.6) UDF-EXT-7/9-E-35 2-ft Rack Extension; for use with unequal flange rack 24.0 x 25.9 x (UDF-ER-7-E-35) (60.9 x 65.8 x 25.7) (9.1) UDF-EXT-7/11-E ft Rack Extension; for use with unequal flange rack 54.0 x 25.9 x (UDF-ER-7-E-35) (137.0 x 65.8 x 25.7) (15.8) 22

25 FDC Product Specifications: Frames and Components Frame Components End Caps End caps provide protection for the end of each row of bays. End caps are not required between the racks in a given row (must be ordered separately). ZA-054 Foot Caps Foot caps are a protective covering at the base of the rack that allow mounting of A/C outlets as required in the frame system. Interbay Storage Units Interbay Storage Units (IBUs) route and manage jumpers on the front of the FDF or UDF. The IBUs have 9 routing hubs, a top jumper trough bridge, and a bottom jumper trough. ZA-1653 End Cap (FDF-EC-7) ZA-2105 Foot Cap (FDF-B-10) Interbay Storage Unit (UDF-IBU-7-1) 23

26 FDC Product Specifications: Frames and Components Frame Components Ordering Information End Caps Part Dimensions (H x W x D) Shipping Weight Number Description in (cm) lb (kg) FDF-EC-7 End Cap for 7-ft equal flange rack (FDF) 83.6 x 3.0 x 12.0 (212.4 x 7.6 x 30.5) 54.0 (24.4) FDF-EC-9 End Cap for 9-ft equal flange rack (FDF) x 3.0 x 12.0 (274.1 x 7.6 x 30.5) 75.0 (34.0) (7-ft end cap plus 2-ft extension) FDF-EC-11 End Cap for 11.5-ft equal flange rack (FDF) x 3.0 x 12.0 (350.2 x 7.6 x 30.5) 85.0 (38.5) (7-ft end cap plus 4.5-ft extension) UDF-EC-7-35 End Cap for 7-ft unequal flange rack (UDF) 83.6 x 3.0 x 12.0 (212.4 x 7.6 x 30.5) 35.0 (15.9) UDF-EC-9-35 End Cap for 9-ft unequal flange rack (UDF) x 3.0 x 12.0 (274.1 x 7.6 x 30.5) 45.0 (20.4) (7-ft end cap plus 2-ft extension) UDF-EC End Cap for 11.5-ft unequal flange rack (UDF) x 3.0 x 12.0 (350.2 x 7.6 x 30.5) 55.0 (24.9) (7-ft end cap plus 4.5-ft extension) FDF-EC-EXT-7/9 2-ft End Cap Extension for equal flange 24.0 x 3.0 x 12.0 (60.9 x 7.6 x 30.5) 15.0 (6.8) rack (FDF) FDF-EC-EXT-7/ ft End Cap Extension for equal flange 54.0 x 3.0 x 12.0 (137.0 x 7.6 x 30.5) 34.6 (15.6) rack (FDF) UDF-EC-EXT-7/ ft End Cap Extension for unequal flange 24.0 x 3.0 x 12.0 (60.9 x 7.6 x 30.5) 10.0 (4.5) rack (UDF) UDF-EC-EXT-7/ ft End Cap Extension for unequal flange 54.0 x 3.0 x 12.0 (137.0 x 7.6 x 30.5) 22.5 (10.2) rack (UDF) Foot Caps Part Dimensions (H x W x D) Shipping Weight Number Description in (cm) lb (kg) FDF-B-10 Foot Cap; covers front or back of the base 5.5 x 24.2 x 4.6 (14.0 x 61.6 x 11.8) 5.0 (2.3) of the FDF-ER-7 frame FDF-B-19 Foot Cap for 19-in frame: covers front or back 5.5 x 21.9 x 4.6 (14.0 x 55.6 x 11.8) 5.0 (2.3) of the base of the FDF-ER-7-19 Interbay Storage Units Part Dimensions (H x W x D) Shipping Weight Number Description in (cm) lb (kg) FDF-IBU-7-1 Interbay Storage Unit, FDF 84.0 x 4.75 x 6.0 (213.1 x 12.1 x 15.2) 20.0 (9.1) UDF-IBU Interbay Storage Unit with 84.0 x 4.75 x 6.0 (213.1 x 12.1 x 15.2) 20.0 (9.1) Jumper Trough, UDF UDF-IBU Interbay Storage Unit, with 84.0 x 4.75 x 6.0 (213.1 x 12.1 x 15.2) 20.0 (9.1) large Jumper Trough, UDF 24

27 FDC Product Specifications: Frames and Components Frame Components Jumper Troughs and Jumper Trough Bridges Jumper troughs organize and protect jumpers routed on the front of the frame, and also allow jumper routing from one side of the rack to the other. Jumper troughs are also used for express routing of jumpers through the bay to adjacent bays. Jumper troughs are available in a variety of sizes. Jumper trough bridges provide increased support between bays. ZA-1649 ZA-2148 FDF Jumper Trough (FDF-JT-23) FDF Deep Bottom Trough (FDF-JT-23BX) FDF Jumper Trough (FDF-XT-23) ZA-1642 FDF Jumper Trough Bridge (FDF-JT-TB) 25

28 FDC Product Specifications: Frames and Components Frame Components Ordering Information Jumper Troughs and Jumper Trough Bridges Part Dimensions (H x W x D) Shipping Weight Number Description in (cm) lb (kg) FDF-JT in tall Jumper Trough; three troughs fit in a 1.7 x 23.0 x ft frame with eight of the 8.75-in tall housings; (4.3 x 58.4 x 11.4) (1.8) front tab height is 1.41 in; width is 4.5 in FDF-XT in tall Jumper Trough; two troughs fit in a 3.2 x 23.0 x ft frame with eight of the 8.75-in tall housings; (8.3 x 58.4 x 11.4) (1.8) front tab height is 2.75 in; width is 4.5 in FDF-OXT-23 Open Jumper Trough; nonstandard top or bottom, 4.5 x 23.0 x but must be used in conjunction with FDF-JT-23 (11.4 x 58.3 x 11.4) (1.8) FDF-JT-TB Trough Bridge; connects the FDF-JT-23 trough 2.0 x 6.0 x between bays (5.1 x 15.2 x 5.1) (0.2) FDF-XT-TB Trough Bridge; connects the FDF-XT-23 trough 3.0 x 6.0 x between bays (7.6 x 15.2 x 5.1) (0.3) FDF-XT-TB-B Trough Bridge; connects the FDF-XT-23 trough 2.8 x 6.6 x between bays; for use at bottom position (7.1 x 16.7 x 11.1) (0.4) FDF-JT in tall Jumper Trough; three troughs fit in a 2.25 x 19.0 x ft frame with eight of the 8.75-in tall housings; (5.72 x x 11.4) (1.8) front tab height is 1.41 in; width is 4.5 in FDF-JT-19-2RS 3.5-in tall Jumper Trough 3.46 x 19.0 x 3.8) 4.0 (8.8 x 48.2 x 9.6) (1.8) FDF-JT-23BX Bottom Jumper Trough, Deep for FDF x x 5.0) 4.0 (29.0 x 65.5 x 12.7) (1.8) 26

29 FDC Product Specifications: Frames and Components Frame Components Routing Guides Routing guides work in combination with other frame components to organize and protect cables on the front and rear of the frame. Corning Cable Systems offers three types of routing guides: jumper routing guides (for the front of the frame), cable tie brackets (for cables on the rear of the frame), and vertical cable guides (for the front and back of the frame). Jumper Routing Guides ZA-090 Jumper Covers Jumper covers enclose fibers routing vertically between housings on an FDF bay. Jumper covers are made of a clear-tinted plastic that matches the doors on the connector module housings one set of covers (upper and lower half) can protect a 7-ft section on one side of the frames. Two sets of covers are required to cover the entire frame. Jumper covers are optional accessories and are not necessary for frame installation. FDF-RG-10 FDF-RG-20 Jumper Cover Vertical Cable Guide Cable Tie Brackets ZA-1639 ZA-2137 ZA-051 FDF-CTB FDF-VCG UDF-CTB FDF-JC-02 27

30 FDC Product Specifications: Frames and Components Frame Components Ordering Information Routing Guides Part Dimensions (H x W x D) Shipping Weight Number Description in (cm) lb (kg) FDF-RG-10 Standard Routing Guide; organizes the routing 3.0 x 3.0 x of jumpers in a frame (7.6 x 7.6 x 10.2) (0.5) FDF-RG-20 Open Routing Guide; organizes the routing 3.5 x 1.5 x of jumpers in a frame (8.9 x 3.8 x 10.2) (0.5) FDF-VCG Vertical Cable Guide 8.19 x 3.0 x (21.0 x 7.6 x 31.0) (0.9) FDF-CTB Set of 10 cable tie brackets for securing cables on the 0.7 x 4.6 x rear of the frame; for use with equal flange frames (FDF) (1.8 x 11.7 x 3.3) (0.5) UDF-CTB Set of 12 cable tie brackets for securing cables on the 0.2 x 3.0 x rear of the frame; for use with unequal flange frames (UDF) (0.46 x 7.6 x 0.33) (0.5) Jumper Covers Part Dimensions (H x W x D) Shipping Weight Number Description in (cm) lb (kg) FDF-JC-02 Optional Smoked Jumper Cover Panel; covers one 40.5 x 3.5 x side of the front jumper routing area (102.9 x 8.9 x 0.15) (1.4) 28

31 FDC Product Specifications FDC System Examples The following chart illustrates the bill of materials required for a typical FDC system of various fiber counts. Note: The FDF frame will accommodate a maximum of 8 FDC-CMH-072 housings per bay. Fiber Count Hardware * 720 FDF ft Network Bay; includes a 7-ft equal flange frame and top, middle, and bottom jumper troughs (Page 18-19) FDF-IBU ft Interbay Storage Unit (Page 22-23) FDF-EC ft End Cap (Page 22-23) FDC-CMH fiber FDC Connector Module Housing (Page 4-5) FDC-CP1P fiber FDC Connector Panel with SC Adapters (Page 7) * See illustration on page 30 for recommended layout for 576 fibers. 29

32 FDC Product Specifications FDC System Examples Recommended FDC System Layout for 576 Fibers Jumper Trough FDC-CMH-072 FDC-CMH-072 FDC-CMH-072 FDC-CMH-072 Jumper Trough FDC-CMH-072 FDC-CMH-072 FDC-CMH-072 FDC-CMH-072 Jumper Trough FDF-IBU-7-1 FDF-EC-7 30

33 FDC Product Specifications FDC Product Family Part Number Index Part Number Page Number Part Number Page Number Part Number Page Number FDC FDC-001-F...3 FDC FDC-002-F...3 FDC FDC-003-F...3 FDC FDC-004-F...3 FDC FDC-005-F...3 FDC-AC FDC-BLANK...8 FDC-CM0...8 FDC-CM FDC-CM FDC-CMH FDC-CMH FDC-CMH FDC-CMH FDC-CMH FDC-CMH-E4...5 FDC-CP0...8 FDC-CP0P...8 FDC-CP0P-25T...8 FDC-CP0P FDC-CP0P FDC-CP0P FDC-CP FDC-CP FDC-CP1P FDC-CP1P FDC-CP8...8 FDC-CP8P FDC-CP8P FDC-CP8P-ST...8 FDC-JSH FDC-JSM...6 FDC-RF FDC-SMH FDC-SMH-3-F...13 FDC-SMH FDC-SMH-5-F...13 FDF FDF FDF FDF FDF-B FDF-CTB FDF-EC FDF-EC FDF-EC FDF-EC-EXT-7/ FDF-EC-EXT-7/ FDF-ER FDF-ER FDF-ER FDF-EXT-7/ FDF-EXT-7/ FDF-IBU FDF-IBU FDF-IBU FDF-JC FDF-JT FDF-JT-TB FDF-OXT FDF-RG FDF-RG FDF-XT FDF-XT-TB...26 FDF-XT-TB-B...26 M M M M UDF E UDF E UDF E UDF E UDF-CTB...28 UDF-EC UDF-EC UDF-EC UDF-EC-EXT-7/ UDF-EC-EXT-7/ UDF-ER-7-E UDF-ER-9-E UDF-EXT-7/9-E UDF-EXT-7/11-E UDF-IBU UDF-IBU UST UST

34 Notes: 32

35 For further details on how to install Corning Cable Systems FDC unit products, please refer to the following Corning Cable Systems Recommended Procedures: FDC Installation SRP FDF Installation SRP UDF Frame Instructions SRP FDF Jumper Planning Guide SRP Corning Cable Systems reserves the right to improve, enhance, and modify the features and specifications of Corning Cable Systems products without prior notification. FDC, ALTOS, TBII, and MIC are registered trademarks of Corning Cable Systems Brands, Inc. FREEDM, Hyper, LSZH, and OptiStrip are trademarks of Corning Cable Systems Brands, Inc. SC-DC and ALTOS/LSZH are trademarks of Corning Cable Systems LLC. ST is a registered trademark of Lucent Technologies. All other trademarks are the properties of their respective owners. 1995, 2000 Corning Cable Systems All Rights Reserved. Printed in USA. ICH-102C / August 2000 / 3.5M Corning Cable Systems LLC PO Box 489 Hickory, NC USA FAX: International:

36 FDC Hardware Product Family