FIELD TECHNICAL INFORMATION

Transcription

1 NEC Engineering, Ltd. Field Service Engineering Department, IPB FIELD TECHNICAL INFORMATION Setting up Dterm IP with Legacy Phone on NEAX2400 IPX FTI-327/TI-327 ISSUE 1 September 30, 2004 Field Service Engineering Department This FTI (Field Technical Information) provides for the basic fundamental settings in setting up a system with Dterm IP and connections with Legacy Phones on NEAX2400 IPX. 1. System Layout The service feature.. IPX ELC Dterm 2000 IPPAD PHD CPU (MGC) HUB DtermIP DtermIP Software Merged - BASIC (Main Software) eg. SC-3164 IPX BS PROG-R14 - Standard (Line Capacity Software) eg. SB-915 IPX STD IP License (For using IP Phones) eg. SB-937 IPX IP4 (4 ports) Important: Data assigned in Virtual PIM also needs be counted in Standard (Line Capacity Software) Virtual Virtual Physical Physical Just as an example: If you have 2 physical PIMS and 2 Virtual PIMs (non existent) where you have assigned virtual station data for Dterm IP you will need include the amount in Line Capacity License even though physically the PIM is nonexistent. In this example SB-915 IPX STD For more information on Virtual PIMS see Feature Programming Manual Chapter 2 Assignment of Basic Office data Section 14 Virtual PIM Data (ND-71550(E)).

2 3. Circuit Card Switch Setting PHD SPA-CC118 Switch Setting (Slot 16 of PIM 0) SW01 ALL OFF (not used) SW02 (Mode) 0 (au negotiation) SW10 1 = Off Accommodated in ordinary slot 2,3,4,5,6,7 = Not used PA-32IPLB Switch Settings (Slot 21 of PIM 0) SW01 ALL OFF SW02 (Mode) 0 (au negotiation) SW10 ALL OFF SW11 ALL OFF SW12 5 = ON / 1,2,3,4,6,7,8 = OFF SW13 7 = ON / 1,2,3,4,5,6,8 = OFF SW14 5,6,7 = ON / 1,2,3,4,8 = OFF 4. Data Assignment a) ASYD SYS INDEX DATA CONTENTS Number of MG Number of Main Processor Configuration of TDW Releasing Method for Station Station Calling Service Number of Tenants C Digit Station Number DM Capacity Default = 2 megabytes CM Capacity Default = 2 megabytes C Configuration of CPU Music On Hold Service, TSW Compression A-Law 1 65 FF Maximum Number of Routes Kind of Service Class (Dterm) Dterm F Common Tenant Table 1 93 FB Common Tenant Table 1 94 FF Common Tenant Table IMG Mounting Status IMG Mounting Status My Line Display Call Transfer Service Ringer Pattern (Incoming Trunk Call) Ringer Pattern (Station) Ringer Pattern 0

3 b) ASYDL SYS INDEX DATA CONTENTS Memory Block for LDM DE Pim 0,1,2 Pim 3 is Virtual PIM Dterm BF Common Tenant Data Table c) AUNT MG TYPE UNIT 0 =1 00 / =1 2 =1 3 =1 d) SINZ (System Initial) e) ADTM (Assign IP Address PBX MGC (Media Gateway Converter)) IP Address Subnet Mask NIC Default Gateway Au Negotiation Note: MGC will be reset. f) ATNR D/N OGTN TMTN TRI RES D Note: TRI 0 = Extension Extension Connection g) ANPD TN 1st DC CI NND BLF 1 2 N H 4 0 h) ASPA TN 1st DC CI SRV 1 2 N H STN

4 i) ATRK RT TK LENS j) ASDT TN STN LENS TEC RSC SFC Setting IP Extension Extension Basic Data Setting k) ASYDL SYS INDEX DATA BIT Description All bits Dterm IP Tone Country Number 04= A-Law Standard l) ALIDL l-1) PHD Circuit Cards LAN information (IP Address etc.) is registered with this command. l-2) Necessary data for connecting an IP network (IP address, Default gateway, Subnet Mask) is be assigned or deleted. l-3) After assigning or deleting information by the command always make sure reinitialize the PH (Procol Handler) Circuit Card. LENS TYPE PH-IP Def. GW IP NETMASK PORT REGMAX PH-D l-4) For Internal PHD (No PHD circuit card is necessary) please consult the manual for setting. (This feature is available for FP8700 or R14). Location: Documentation Feature Programming Manual Chapter 2 Assignment of Basic Office Data Section 15 Internal PHD Data. m) AISTL : IP Extension Extension Data (LDM) IP Extension (Dterm 75 (IP), Dterm SP20/SP30, Analog MC etc.) data assignment / deletion. m-1) It is necessary a assign the IP Extensions virtual line an open or available LENS.

5 m-2) Extension assignment of a previously assigned extension or trunk will result in an error message being displayed. m-3) Applicable tenant number maximum will be governed by the maximum set in the ASYD command (Sys-1 Index-8). m-4) Extension digit count maximum is governed by the maximum set in ASYD command (Sys-1, Index-16). m-5) Route Restriction Class (RSC) and Service Feature Class (SFC) are assigned by the ARSC and ASFC commands respectively. m-6) Previously established (assigned) Analog MC data cannot be overwritten by other IP terminal data (Dterm 75 (IP), Dterm SP20/SP30, etc.) The reverse also applies. TN IP STN KIND TEC RSC SFC LENS Dterm IP Dterm IP n) AKYD (Assign Logout Butn) The example below shows only 2050 but assign the same for TN STN PRI PLTN STN S NWD LNPRE TP KYN KYI FKY KD Multi-Line TN Multi-Line STN RG o) Optional Setting (ToS, QoS, Jitter Buffer, Payload, PAD, Echo Canceller) The following can be set by the two commands ALOCL and AIVCL.(Refer Manual) o-1) ALOCL : IP Location Data (LDM) Assignment of IP Location ID. Information such as network address, mask bit, LOC-ID, service type, ToS operation is assigned by using this command. NOTE-1: Location ID (LOC-ID) basically identifies the specific group which equipment connects the network by referring the assigned Network address. With this location ID number services such as bandwidth management can be enacted. o-2) AIVCL : IP Service Voice Compression Management Data (LDM) OPTIONAL Assignment of IP Service Voice Compression Management data. This command is used assign/delete the voice packet control data such as Jitter Buffer, ToS, Payload, PAD, and Echo Canceller features corresponding the specified Location IDs. NOTE-2: When no data is set with ALOCL and AIVCL default Payload (CODEC) used between terminals / Network Address points is G.711 with a size of 40 ms. Please see AIVCL command for other defaults.

6 4.2 IPPAD Data Setting Procedure Assign connection trunk information for IP PAD circuit card by ACRD / ACTK command. p) ACRD : Assignment for Connection Route Class Data (LDM) Assign Voice route class data. CDN Function C_RT 10 CDN: 1 TF 3: BWT CDN: 2 TCL 4: Netfusing CDN: 3 RLP 2: First Party Release CDN: 4 SMDR 0: Fixed CDN: 5 LSG 12: B channel CDN: 6 PAD 7: 0DB CDN: 7 TRKS 0 (1): Select from the trunk which becomes idle first (last) CDN: 8 TC/EC 0: No MPC/EC CDN: 9 FINT 0: Fusion Standard CDN: 10 EPEG 0: Fixed CDN: 11 TC 0: Fixed CDN: 12 MTC 0: Fixed CDN: 13 STSEQ 0: Fixed CDN: 14 FGH 0: FCH CDN: 15 MMN 0: TDM CDN: 16 LKIND 0: DTI CDN: 17 IPLYR 1: 2M CDN: 18 IPTRK 0: Out of Service CDN: 19 IP-PAD 1: IP_PAD q) ACTK : Assignment of Connection Trunk Data (LDM) Assign Connection Trunk Data in LENS of IP PAD Circuit Card. C_RT C_TK LENS r) AFPC : Assignment of FCCH Routing Data (LDM) Assign Connection Route Number (C_RT) of IP PAD in FPC = 0 FPC 0 FCCH 0 P_ROUTE 0 CNT 1 C_RT 10 FCHN/FPCN 0

7 s) ALIDL : Assignment of LAN information (LDM) Assign LAN information of IP PAD circuit card (IP Address, Jitter Buffer, Payload, Type/Size). LENS TYPE PH IP Def_GW NETMSK PORT Reg (5 digits) Max IP-PAD t) MBCT : Assignment of Connection Trunk Make Busy (LDM) Make Idle Connection trunk of IP-PAD circuit card. C_RT C_TK MB Setting up Dterm IP u) To set up the Dterm IP please note the following instructions. u-1) Dterm75 with IP adapter, or Dterm Series i phones. u-2) Connect power supply the IP phone, get in Dterm IP setting mode press Hold + Transfer + * + # in sequential order. u-3) Items set in Dterm IP. Dterm Item Description Setting 1 DHCP Mode Disable 2 DRS Primary (IP address of IPX) 4 IP Address (IP Address of Dterm IP) 5 Default Gateway Subnet Mask Note: * astericks key is used skip next area when setting IP addresses. u-4) Push SAVE butn which is designated on the Dterm IP display. u-5) Connect LAN cable. u-6) The Dterm IP will start up Initializing and after a few seconds should go in Login mode. Enter 2050 and 2051 for the second Dterm IP. 4. Test 4.1 Call each other by dialing IP Dterm 2050 IP Dterm Call a legacy phone by dialing 2000 from an IP Dterm and vice versa.