CyberData VoIP V2 Speaker with VoIP Clock Kit Configuration Guide for OmniPCX Enterprise
|
|
- Merryl Parrish
- 5 years ago
- Views:
Transcription
1 CyberData VoIP V2 Speaker with VoIP Clock Kit Configuration Guide for OmniPCX Enterprise CyberData Corporation 2555 Garden Road Monterey, CA T: F:
2 2 Introduction 1.0 Introduction The CyberData VoIP Ceiling Clock-Speaker V2 is a SIP enabled speaker that can be connected to the OmniPCX Enterprise via SIP device or external voice mail to broadcast messages to a campus area such as schools hallways from any internal or external phone connected to the OmniPCX Enterprise as well. The CyberData V2 Speaker accepts direct RTP packets using codec s G-711 µ- Law or A-Law. Figure 1. CyberData VoIP Ceiling Clock-Speaker V2 Network/Link Activity (Yellow) Speaker Status (Green) The VoIP Clock Kit has two (2) Status and Activity LEDs: Network Link/Activity (yellow): it is a yellow LED indicating the LAN connectivity. Speaker Status (green): it is a green LED indicating the status of the board. 1.1 Network Link/Activity (yellow) Description: This LED indicates the boot phase in the following steps: 1. The yellow LED comes on immediately after power up. 2. If the network link is established it remains on. When there is network activity this LED blinks. The CyberData V2 Speaker sends SIP Register to the OmniPCX Enterprise about 60 seconds after boot.
3 3 Physical Connection 1.2 Speaker Status LED (green) description: This LED indicates the boot phase in the following steps: 1. The green LED comes on approximately seven seconds after power up. 2. After about 23 seconds (with a static IP address) or 27 seconds (if the board is set to use DHCP), the green LED will blink six times to indicate that the board is fully booted. 3. After about 56 seconds, the speaker will beep if the parameter Speaker Beep After Initialization is enabled. 2.0 Physical Connection The CyberData V2 Speaker can only be connected to an 802.3af compliant Power over Ethernet (PoE) Switch. Figure 2 illustrates how to connect the CyberData V2 Speaker to a 802.3af compliant PoE switch via a Cat 5 Ethernet cable. Figure 2. CyberData V2 Speaker Physical Connection Cat 5 Ethernet cable 802.3af Compliant PoE Switch VoIP V2 Speaker
4 4 CyberData V2 Speaker Configuration 3.0 CyberData V2 Speaker Configuration The factory default settings of CyberData V2 Speaker are listed below: IP Addressing mode: DHCP IP Address: determined by DHCP server Web Access Username: admin Web Access Password: admin Subnet Mask: determined by DHCP server Default Gateway: determined by DHCP server To find out the IP address of the Speaker, you may run the Discover Utility which is available for download at the following page: In Figure 3, the Discovery Utility window displays all of the SIP Speakers within your network after clicking on the Scan button. Figure 3. CyberData V2 Speakers scanned by Discover Utility Scan button Launch Browser button
5 5 CyberData V2 Speaker Configuration 1. After discovering the IP address, click the Launch Browser button to open the web browser to access the Home Page. 2. When prompted, use the following default Web Access Username and Web Access Password to access the Home Page (Figure 4): Web Access Username: admin Web Access Password: admin Figure 4..Home Page
6 6 CyberData V2 Speaker Configuration 3.1 Network Setup 1. Click on the Networking button to go to the Network Configuration page. 2. Click on the Static radio button to change the IP address to Static. Figure 5..Network Configuration Page 3. Set the IP Address, Subnet Mask and Default Gateway according to the customer s network architecture. 4. After changing the parameters, click Save Settings which updates the changed parameters and reboots the device if appropriate.
7 7 CyberData V2 Speaker Configuration 3.2 Device Configuration Click on the Device Config button to set the device parameters on the Device Configuration page. Figure 6. Device Configuration Page 1. Check the Auto-Answer Incoming Calls box to enable the device to automatically answer incoming calls. 2. After changing the parameters, click the Save button. The device will reboot. 3. Click on the Test Audio button to test the audio and ensure that the CyberData V2 Speaker is functional.
8 8 CyberData V2 Speaker Configuration 3.3 SIP Configuration Click on the SIP Config button to change the SIP settings on the SIP Configuration page. Figure 7. SIP Configuration Page 1. Set the following parameters: SIP Server: The OmniPCX Enterprise Main CPU IP Address ( in this example) Remote SIP Port and Local SIP Port: 5060 SIP User ID and Authenticate ID: The directory number assigned by the customer to the CyberData V2 Speaker (4001 in this example). Click to check the Register with a SIP Server box. Re-registration Interval (in seconds): 3600 (1 hour). Note Make sure that the Re-registration interval value is greater than the minimum accepted by the OmniPCX Enterprise under SIP Registrar. 2. The CyberData V2 Speaker will reboot after you click on the Save button.
9 9 OmniPCX Enterprise Configuration 3. Check to see whether the SIP Registration was accepted by the OmniPCX Enterprise by entering the command sipregister. If the SIP Registration was accepted, you should be able to see something similar to the following on the screen: (4)oxe> sipregister ************************************************* Dump local registrar base Address of record : 4001 contact : udp, 2225 s ************************************************* ****** registered user number : 1 ************************************************* 4.0 OmniPCX Enterprise Configuration The CyberData V2 Speaker can be configured in the OmniPCX Enterprise as a SIP Device or as an External SIP Voice Mail. The CyberData V2 Speaker works properly when the OmniPCX Enterprise sends re-invite after the user places the call on hold. The user can actually make a conference with another Speaker. Unlike the version CyberData Version 1 Speaker, the V2 Speaker did not present any issues during some tests that were conducted. 4.1 SIP Subnetwork Set the parameter Protocol Type = ABC_F under the Translator\Network Routing Table: Figure 8. Network Routing Table
10 10 OmniPCX Enterprise Configuration 4.2 SIP Trunk Group Set the following parameters under Trunk Groups: Remote Network: The network number under Translator\Network Routing Table reserved to all external SIP devices, Trunk Group Type: T2, Q931 Signal variant: ABC-F. T2 Specification: SIP Figure 9. Trunk Groups 4. Set the following parameters under Trunk Groups\Trunk Group: Quality profile for voice over IP: Always VoIP, IP Compression Type: G 711 Figure 10. Trunk Groups
11 11 OmniPCX Enterprise Configuration 5. Set the parameter Number of SIP Accesses: 2 under Trunk Groups\Trunk Group\Virtual accesses for SIP: Figure 11. Virtual accesses for SIP 4.3 SIP Gateway Set the following parameters under SIP\SIP Gateway: SIP Subnetwork: The network number under Translator\Network Routing Table reserved to all external SIP devices SIP Trunk Group: The trunk group number under Trunk Groups reserved to all external SIP devices. IP Address: OmniPCX Enterprise Main CPU IP Address ( in this example). Figure 12. SIP Gateway
12 12 OmniPCX Enterprise Configuration 4.4 SIP Proxy Set the parameter Minimal authentication method: SIP None under SIP\ SIP Proxy: Figure 13. SIP Proxy 4.5 Configuring CyberData V2 Speaker as SIP Device Set the following parameters under Users: Directory Number: Number selected by the customer that will be used to call the CyberData V2 Speaker Set Type: SIP device URL UserName: SIP User ID under SIP Setup of the CyberData V2 Speaker configuration URL Domain: OmniPCX Enterprise Main CPU IP Address ( in this example) SIP Authentication: Authenticate ID under SIP Setup of the CyberData V2 Speaker configuration. Figure 14. Users
13 13 OmniPCX Enterprise Configuration 4.6 Configuring CyberData V2 Speaker as External SIP Voice Mail Set the following parameters under Applications\External Voice Mail: Voice Mail Dir.No: Number selected by the customer that will be used to call the CyberData V2 Speaker URL UserName: SIP User ID and Authenticate ID under SIP Setup of the CyberData V2 Speaker configuration URL Domain: OmniPCX Enterprise Main CPU IP Address ( in this example) Figure 15. External Voice Mail
Elastix Server VoIP Intercom Setup Guide
The IP Endpoint Company Elastix Server VoIP Intercom Setup Guide CyberData Corporation 2555 Garden Road Monterey, CA 93940 T:831-373-2601 F: 831-373-4193 www.cyberdata.net 2 1.0 Setup Diagram Figure 1
VoIP Ceiling Speaker with Allworx 6x Server Setup Guide
VoIP Ceiling Speaker with Allworx 6x Server Setup Guide CyberData Corporation 2555 Garden Road Monterey, CA 93940 T:831-373-2601 F: 831-373-4193 www.cyberdata.net 2 1.0 Setup Diagram Figure 1-1 is a setup
3COM VCX PBX Server VoIP Intercom Setup Guide
3COM VCX PBX Server VoIP Intercom Setup Guide CyberData Corporation 2555 Garden Road Monterey, CA 93940 T:831-373-2601 F: 831-373-4193 www.cyberdata.net 2 1.0 Setup Diagram Figure 1 is a setup diagram
VoIP Zone Controller: 4-Port Audio Out Operations Guide
The IP Endpoint Company VoIP Zone Controller: 4-Port Audio Out Operations Guide SiP Compliant 010881 Document Part #930109D for Firmware Version 1.0.6 CyberData Corporation 3 Justin Court Monterey, CA
VoIP Intercom with Allworx 6x Server Setup Guide
VoIP Intercom with Allworx 6x Server Setup Guide CyberData Corporation 2555 Garden Road Monterey, CA 93940 T:831-373-2601 F: 831-373-4193 www.cyberdata.net 2 1.0 Setup Diagram Figure 1-1 is a setup diagram
Quick Installation Guide
Quick Installation Guide PRI Gateway Version 2.4 Table of Contents Hardware Setup... 1 Accessing the WEB GUI... 2 Notification LEDs (On the Front Panel of the Gateway)... 3 Creating SIP Trunks... 4 Creating
Configuring CyberData Devices for Intermedia Hosted PBX
The IP Endpoint Company Configuring CyberData Devices for Intermedia Hosted PBX This procedure was written by: CyberData Corporation 3 Justin Court Monterey, CA 93940 T:831-373-2601 F: 831-373-4193 www.cyberdata.net
VoIP Intercom and Cisco Call Manager Server Setup Guide
The IP Endpoint Company VoIP Intercom and Cisco Call Manager Server Setup Guide CyberData Corporation 2555 Garden Road Monterey, CA 93940 T:831-373-201 F: 831-373-4193 www.cyberdata.net 2 1.0 Setup Diagram
Configuring CyberData VoIP Ceiling Speakers
NetVanta Unified Communications Technical Note Configuring CyberData VoIP Ceiling Speakers Introduction The CyberData Voice over IP (VoIP) ceiling speaker connects to existing local area networks (LANs)
NEC Univerge PBX VoIP Intercom Setup Guide
The IP Endpoint Company NEC Univerge PBX VoIP Intercom Setup Guide CyberData Corporation 3 Justin Court Monterey, CA 93940 T:831-373-2601 F: 831-373-4193 www.cyberdata.net 2 1.0 Setup Diagram Figure 1
RingCentral Office. Configure Grandstream phones with RingCentral. To contact RingCentral, please visit www.ringcentral.com or call 1-800-574-5290.
TM RingCentral Office Configure Grandstream phones with RingCentral Configuring Grandstream phones Overview... 2 Getting ready to setup your Grandstream phones... 2 Configuring the Grandstream Phone...
THINKTEL COMMUNICATIONS DIGIUM G100/G200 PRI OVER IP SIP TRUNKING
THINKTEL COMMUNICATIONS DIGIUM G100/G200 PRI OVER IP SIP TRUNKING TA B L E O F C O N T E N T S 1.1 NETWORK DIAGRAM... 3 1.2 COLLABORATION OF MONARQUE TELECOM... 3 1.3 CONNECTING TO THE DIGIUM G100... 4
VoIP Network Configuration Guide
The owner friendly phone system for small business VoIP Network Configuration Guide Release 7.10 Copyright 2011 Fortinet, Inc. All rights reserved. Fortinet, FortiGate, FortiGuard, FortiCare, FortiManager,
How to Configure the NEC SV8100 for use with Integra Telecom SIP Solutions
How to Configure the NEC SV8100 for use with Integra Telecom SIP Solutions Overview: This document provides a reference for configuration of the NEC SV8100 IP PBX to connect to Integra Telecom SIP trunks.
FortiVoice. Version 7.00 VoIP Configuration Guide
FortiVoice Version 7.00 VoIP Configuration Guide FortiVoice Version 7.00 VoIP Configuration Guide Revision 2 14 October 2011 Copyright 2011 Fortinet, Inc. All rights reserved. Contents and terms are subject
Version 0.1 June 2010. Xerox WorkCentre 7120 Fax over Internet Protocol (FoIP)
Version 0.1 June 2010 Xerox WorkCentre 7120 Fax over Internet Protocol (FoIP) Thank you for choosing the Xerox WorkCentre 7120. Table of Contents Introduction.........................................
Configuring the CyberData VoIP 4-Port Zone Controller with Audio Out
NetVanta Unified Communications Technical Note Configuring the CyberData VoIP 4-Port Zone Controller with Audio Out Introduction The CyberData Voice over Internet Protocol (VoIP) zone controller enables
6.40A AudioCodes Mediant 800 MSBG
AudioCodes Mediant 800 MSBG Page 1 of 66 6.40A AudioCodes Mediant 800 MSBG 1. Important Notes Check the SIP 3 rd Party Validation Website for current validation status. The SIP 3 rd party Validation Website
Application Note. IP8000 Conference Phone Configuration Guide. Table of Contents. Overview. Requirements. ST-10010 October 25, 2007
Application Note ST-10010 October 25, 2007 IP8000 Conference Phone Configuration Guide This application note provides the details on adding the IP8000 conference phone to the ShoreTel IP phone system.
SIP Trunking using Optimum Business SIP Trunk Adaptor and the Allworx 6x IP PBX 7.1.6.1
ALLWORX SIP Trunking using Optimum Business SIP Trunk Adaptor and the Allworx 6x IP PBX 7.1.6.1 Goal The purpose of this configuration guide is to describe the steps needed to configure the Allworx 6x
Broadband Phone Gateway BPG510 Technical Users Guide
Broadband Phone Gateway BPG510 Technical Users Guide (Firmware version 0.14.1 and later) Revision 1.0 2006, 8x8 Inc. Table of Contents About your Broadband Phone Gateway (BPG510)... 4 Opening the BPG510's
Integrating a Hitachi IP5000 Wireless IP Phone
November, 2007 Avaya Quick Edition Integrating a Hitachi IP5000 Wireless IP Phone This application note explains how to configure the Hitachi IP5000 wireless IP telephone to connect with Avaya Quick Edition
Configuring the Avaya B179 SIP Conference Phone with Avaya Aura Communication Manager and Avaya Aura Session Manager Issue 1.0
Avaya Solution & Interoperability Test Lab Configuring the Avaya B179 SIP Conference Phone with Avaya Aura Communication Manager and Avaya Aura Session Manager Issue 1.0 Abstract These Application Notes
Quick Installation Guide. Overview. PLANET VIP-156/VIP-156PE/VIP-158 Quick Installation Guide
Quick Installation Guide Overview This quick installation guide describes the objectives; organization and basic installation of the PLANET VIP-156/VIP-156PE/VIP-158 VoIP Phone Adapter, and explains how
TALKSWITCH VOIP NETWORK TROUBLESHOOTING GUIDE
TALKSWITCH DOCUMENTATION TALKSWITCH VOIP NETWORK TROUBLESHOOTING GUIDE RELEASE 3.24 CT.TS005.008001 ANSWERS WITH INTELLIGENCE COPYRIGHT INFORMATION TalkSwitch. Copyright 2006. All Rights Reserved. Reproduction,
Optimum Business SIP Trunk Set-up Guide
Optimum Business SIP Trunk Set-up Guide For use with IP PBX only. SIPSetup 07.13 FOR USE WITH IP PBX ONLY Important: If your PBX is configured to use a PRI connection, do not use this guide. If you need
How to Configure the Cisco UC500 for use with Integra Telecom SIP Solutions
How to Configure the Cisco UC500 for use with Integra Telecom SIP Solutions Overview: This document provides a reference for configuration of the Cisco UC500 IP PBX to connect to Integra Telecom SIP Trunks.
P160S SIP Phone Quick User Guide
P160S SIP Phone Quick User Guide Version 2.2 TABLE OF CONTENTS 1.0 INTRODUCTION... 1 2.0 PACKAGE CONTENT... 1 3.0 LIST OF FIGURES... 2 4.0 SUMMARY OF KEY FUNCTIONS... 3 5.0 CONNECTING THE IP PHONE... 4
Mediatrix 4404 Step by Step Configuration Guide June 22, 2011
Mediatrix 4404 Step by Step Configuration Guide June 22, 2011 Proprietary 2011 Media5 Corporation Table of Contents First Steps... 3 Identifying your MAC Address... 3 Identifying your Dynamic IP Address...
VOIP NETWORK CONFIGURATION GUIDE RELEASE 6.10
TALKSWITCH DOCUMENTATION VOIP NETWORK CONFIGURATION GUIDE RELEASE 6.10 CT.TS005.002606 ANSWERS WITH INTELLIGENCE INTRODUCTION About this guide This guide will help you plan and configure a TalkSwitch system
RingCentral Office. Configure Aastra phones with RingCentral
TM RingCentral Office Configure Aastra phones with RingCentral Configuring Aastra phones Overview... 2 Getting ready to setup your Aastra phones... 2 Configuring the Aastra Phone... 4 Overview Aastra s
VoIP Intercom and Elastix Server
VoIP Intercom and Elastix Server Setup Guide http://www.elastix.org 1.0 Setup Diagram Figure 1-1 is a setup diagram for a single VoIP Intercom configuration. In this configuration, the VoIP Intercom acts
Application Notes for Configuring Yealink T-22 SIP Phones to interoperate with Avaya IP Office - Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for Configuring Yealink T-22 SIP Phones to interoperate with Avaya IP Office - Issue 1.0 Abstract These Application Notes describe the configuration
P-2302HWUDL-P1. Quick Start Guide. 802.11g Wireless VoIP Station Gateway. with Built-in DECT Base Station
P-2302HWUDL-P1 802.11g Wireless VoIP Station Gateway with Built-in DECT Base Station Quick Start Guide Version 3.60 Edition 1 3/2007 Overview The P-2302HWUDL-P1 model is a router with IEEE 802.11g wireless
3CX PBX SIP server 3CX softphone X-Lite softphone HW IP phone - Alphatech IP video door entry phone station
3CX PBX SIP server 3CX softphone X-Lite softphone HW IP phone - Alphatech IP video door entry phone station Before you start: The Alphatech IP video doorphone must be set manually to the SIP proxy mode
2100 Series VoIP Phone
2100 Series VoIP Phone Installation and Operations Manual Made in the USA 3 Year Warranty N56 W24720 N. Corporate Circle Sussex, WI 53089 RP8500SIP 800-451-1460 262-246-4828 (fax) Ver. 4 www.rathmicrotech.com
Savvius Insight Initial Configuration
The configuration utility on Savvius Insight lets you configure device, network, and time settings. Additionally, if you are forwarding your data from Savvius Insight to a Splunk server, You can configure
Allo PRI Gateway and Elastix Server
Allo PRI Gateway and Elastix Server Setup Guide http://www.elastix.org 1.0 Setup Diagram Figure 1-1 is a setup diagram for a single Allo PRI Gateway configuration. We re going to configure a SIP Trunk
VoIPon www.voipon.co.uk sales@voipon.co.uk Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
VoiceGear/3CX Integration Guide Ver.0.1 Page 2 1. OVERVIEW... 3 1.1 SETTING UP 3CX PBX...4 1.2 SETTING UP VOICEGEAR GATEWAY...5 2. VOICEGEAR-3CX SIP INTEGRATION... 6 2.1 3CX CONFIGURATION...7 2.2 VOICEGEAR
TELEPHONE MAN OF AMERICA. Earning Your Business Every Step of the Way!
TELEPHONE MAN OF AMERICA Earning Your Business Every Step of the Way! Specializing in Telecom Equipment of all Brands, Carrier Services, Technician Services, Maintenance Agreements & Purchasing Excess
Digium Switchvox AA65 PBX Configuration
Digium Switchvox SIP Trunking using Optimum Business SIP Trunk Adaptor and the Digium Switchvox AA65 IP-PBX v23695 Goal The purpose of this configuration guide is to describe the steps needed to configure
Epygi Technologies How to Configure Alphatech Cityline IP DP device on the Quadro IP PBX
How to Configure Alphatech Cityline IP DP device on the Quadro IP PBX Abstract: This document describes steps to configure Alphatech Cityline Audio and Video Door Entry IP DP 1CP201 device, hereafter referred
Communication Manager configuration for BLU-103
Avaya Aura Communication Manager configuration for BLU-103 Application Notes for Configuring BLU-103 VoIP Solution with Avaya Aura Session Manager 6.3 and Avaya Aura Communication Manager 6.3 10653 South
1. Panel Descriptions... 1. 2. Connecting the 4 Ports VoIP ADSL Router... 3. 3. Setting up the TCP/IP in Windows... 5
Contents 1. Panel Descriptions... 1 2. Connecting the 4 Ports VoIP ADSL Router... 3 3. Setting up the TCP/IP in Windows... 5 Windows ME/98... 5 Windows 2000... 6 Windows XP... 7 4. Setting up the 4 Ports
SIP Trunking using Optimum Business SIP Trunk Adaptor and the Cisco Call Manager Express Version 8.5
CISCO SIP Trunking using Optimum Business SIP Trunk Adaptor and the Cisco Call Manager Express Version 8.5 Goal The purpose of this configuration guide is to describe the steps needed to configure the
Note: these functions are available if service provider supports them.
Key Feature New Feature Remote Maintenance: phone can be diagnosed and configured by remote. Zero Config: automated provisioning and software upgrading even through firewall/nat. Centralized Management:
Application Note Configuring the Synapse SB67070 SIP Gateway for Broadvox GO! SIP Trunking
Configuring the Synapse SB67070 SIP Gateway for Broadvox GO! SIP Trunking 2012 Advanced American Telephones. All Rights Reserved. AT&T and the AT&T logo are trademarks of AT&T Intellectual Property licensed
Debugging Network Communications. 1 Check the Network Cabling
Debugging Network Communications Situation: you have a computer and your NetBurner device on a network, but you cannot communicate between the two. This application note provides a set of debugging steps
IP PBX. SD Card Slot. FXO Ports. PBX WAN port. FXO Ports LED, RED means online
1 IP PBX SD Card Slot FXO Ports PBX LAN port PBX WAN port FXO Ports LED, RED means online 2 Connect the IP PBX to Your LAN Internet PSTN Router Ethernet Switch FXO Ports 3 Access the PBX s WEB GUI The
Ethernet Port Quick Start Manual
Ethernet Port Quick Start Manual THIS MANUAL CONTAINS TECHNICAL INFORMATION FOR THE ETHERNET PORT OF EDI SIGNAL MONITORS with Ethernet Version 1.5 firmware. DETAILS OF THE ECCOM OPERATION ARE DESCRIBED
Setup Reference guide for PBX to SBC interconnection
Setup Reference guide for PBX to SBC interconnection Method of connection by "LAN interface only" i.e. SBC is placed behind the Perimeter Router / Fire-wall. Panasonic PBX (KX-TDE, NCP series), Media5
NetComm V90 VoIP Phone Quick Start Guide Draft Release 0.1
NetComm V90 VoIP Phone Quick Start Guide Draft Release 0.1 Copyright NetComm Ltd Overview NetComm V90 SIP VoIP Phone User Guide Table of Contents Overview... 3 V90 VoIP Phone Specification...4 Shipping
Connecting the DG-102S VoIP Gateway to your network
Contents of Package: DG-102S VoIP Station Gateway Power adapter CD-ROM, including User s Manual Quick Install Guide Requirements: RS-232 Console Cable Two RJ-45 CAT-5 Straight-Through Cables For more information
NF1Adv VOIP Setup Guide (for Pennytel)
NF1Adv VOIP Setup Guide (for Pennytel) Configuring your NF1Adv for VOIP Service The following steps will take you through the process of setting up your VOIP connection. Step 1: Checking Computer Network
nexvortex Setup Template
nexvortex Setup Template ZULTYS, INC. April 2013 5 1 0 S P R I N G S T R E E T H E R N D O N V A 2 0 1 7 0 + 1 8 5 5. 6 3 9. 8 8 8 8 Introduction This document is intended only for nexvortex customers
SIP-6002 User Guide SIP-6002. User Guide
SIP-6002 User Guide 1 Directory 1. Welcome---------------------------------------------------------------------------------3 2. Installation-------------------------------------------------------------------------------3
VOI-7000 VOI-7100 SIP IP Telephone
VOI-7000 VOI-7100 SIP IP Telephone User Manual 1 Ver 2.01-0609 Table of Contents 1. INTRODUCTIONS... 1 1.1. FEATURES... 1 1.2. PACKING CONTENTS... 2 1.3. LCD DISPLAY AND KEYPADS... 2 2. INSTALLATIONS &
DECT Gigaset N510 IP PRO
DECT Gigaset N510 IP PRO SUMMARY Summary... 1 1. System Features of the DECT Gigaset N510 IP Pro... 2 Base Station Gigaset N510 IP Pro... 2 Environmental Requirements... 3 The base should be placed in
StarMOBILE Network Configuration Guide. A guide to configuring your StarMOBILE system for networking
StarMOBILE Network Configuration Guide A guide to configuring your StarMOBILE system for networking INTRODUCTION... 3 BEFORE YOU BEGIN... 3 1) CONFIRM YOU HAVE THE LATEST SOFTWARE... 3 2) INSTALL THE STARMOBILE
Configuration Notes 283
Mediatrix 4400 Digital Gateway VoIP Trunking with a Legacy PBX June 21, 2011 Proprietary 2011 Media5 Corporation Table of Contents Table of Contents... 2 Introduction... 3 Mediatrix 4400 Digital Gateway
VoIP Intercom Operations Guide
VoIP Intercom Operations Guide Part #010935A CyberData Corporation 2555 Garden Road Monterey, CA 93940 (831) 373-2601 930181E PoE VoIP Intercom Operations Guide 930181E Part # 010935A COPYRIGHT NOTICE:
Configuration Guide for connecting the Eircom Advantage 4800/1500/1200 PBXs to the Eircom SIP Voice platform.
Configuration Guide for connecting the Eircom Advantage 4800/1500/1200 PBXs to the Eircom SIP Voice platform. 1 Contents Introduction.... 3 Installing the Applications Module... 4 Ordering a Licence for
BROADBAND INTERNET ROUTER USER S MANUAL. Version 1.0. - Page 1 of 13 -
Version 1.0 - Page 1 of 13 - 10/100M Broadband Router GETTING TO KNOW 2 3 4 1 5 7 6 - Page 2 of 13 - LED Indicator S/N Indicator Function 1 Power LED (Green) LED lights up steadily indicate that the power
ShorePhone IP 8000 Conference Phone Configuration Guide
Application Note ST-10070 April 16, 2008 ShorePhone IP 8000 Conference Phone Configuration Guide This application note provides the details on adding the IP 8000 conference phone to the ShoreTel Unified
DPH-140S SIP Phone Quick User Guide
DPH-140S SIP Phone Quick User Guide Version 1.0 TABLE OF CONTENTS 1.0 INTRODUCTION... 1 2.0 PACKAGE CONTENT... 1 3.0 LIST OF FIGURES... 2 4.0 SUMMARY OF KEY FUNCTIONS... 3 5.0 CONNECTING THE IP PHONE...
Allworx Installation Course
VPN Hello and welcome. In the VPN section we will cover the steps for enabling the VPN feature on the Allworx server and how to set up a VPN connection to the Allworx System from your PC. Page 1 VPN The
SIP Trunking Service Configuration Guide for Time Warner Cable Business Class
SIP Trunking Service Configuration Guide for Time Warner Cable Business Class NDA-31669 Issue 1.0 NEC Corporation of America reserves the right to change the specifications, functions, or features at
Provisioning and configuring the SIP Spider
Provisioning and configuring the SIP Spider Administrator Guide Table of Contents 1. Introduction... 3 2. Manual Provisioning... 4 3. Automatic Provisioning... 5 3.1 Concept... 5 3.2 Preparing the configuration
SIP Trunking Service Configuration Guide for Skype
SIP Trunking Service Configuration Guide for Skype NDA-31154 Issue 1.0 NEC Corporation of America reserves the right to change the specifications, functions, or features at any time without notice. NEC
Chapter 1 Configuring Basic Connectivity
Chapter 1 Configuring Basic Connectivity This chapter describes the settings for your Internet connection and your wireless local area network (LAN) connection. When you perform the initial configuration
How To Program A Talkswitch Phone On A Cell Phone On An Ip Phone On Your Ip Phone (For A Sim Sim) On A Pc Or Ip Phone For A Sim Phone On Iphone Or Ipro (For An Ipro) On
TALKSWITCH DOCUMENTATION ADDING IP PHONES TO TALKSWITCH RELEASE 6.50 CT.TS005.008104 ANSWERS WITH INTELLIGENCE COPYRIGHT INFORMATION Copyright 2011 Fortinet, Inc. All rights reserved. Fortinet, FortiGate,
Cisco CallManager configuration for BLU-103
Cisco CallManager configuration for BLU-103 This document details the steps required to configure a Cisco CallManager VoIP system to work with a BLU-103 VoIP interface. 10653 South River Front Pkwy, Suite
NF1Adv VOIP Setup Guide (for Generic VoIP Setup)
NF1Adv VOIP Setup Guide (for Generic VoIP Setup) Configuring your NF1Adv for VOIP Service The following steps will take you through the process of setting up your VOIP connection. Step 1: Checking Computer
SIP Trunk Configuration Guide. using
SIP Trunk Configuration Guide using www.cbeyond.net 1-877-441-9783 The information contained in this document is specific to setting up SIP connections between Vertical SBX IP 320 and Cbeyond. If you require
Configuring the Edgewater 4550 for use with the Bluestone Hosted PBX
Configuring the Edgewater 4550 for use with the Bluestone Hosted PBX NOTE: This is an advisory document to be used as an aid to resellers and IT staff looking to use the Edgewater 4550 in conjunction with
PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners.
Trademarks Copyright PLANET Technology Corp. 2004 Contents subject to revise without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective
FLX VoIP Registering with Avaya IP Office 500
FLX VoIP Registering with Avaya IP Office 500 Date: April 5 th, 2012 This technical note gives a detailed description on how to register a Revolabs FLX conference phone with Avaya IP Office 500 PBX. On
Fonality. Optimum Business Trunking and the Fonality Trixbox Pro IP PBX Standard Edition V4.1.2- p13 Configuration Guide
Fonality Optimum Business Trunking and the Fonality Trixbox Pro IP PBX Standard Edition V4.1.2- p13 Configuration Guide Fonality Table of Contents 1. Overview 2. SIP Trunk Adaptor Set-up Instructions 3.
Prestige 2002 Series. VoIP Analog Telephone Adaptor. Quick Start Guide
VoIP Analog Telephone Adaptor Quick Start Guide Version 3.60 5/2005 Overview The Prestige allows you to use an analog telephone to make phone calls over the Internet (Voice over IP or VoIP). It uses SIP
IP Phone Configuration and Troubleshooting Guide
IP Phone Configuration and Troubleshooting Guide NetVanta 7000 Series and IP 700 Series Phones Overview The purpose of this guide: Explain the default configuration. Explain how to configure the NetVanta
Yealink Phones User Guide. 2003-2012 Bicom Systems
I Table of Contents Part I Introduction 1 Part II Requirements 1 Part III Installation 2 1 Power... Adapter 3 2 Power... over Ethernet (PoE) 3 3 IP Address... 3 4 Factory... Settings 3 4 Part IV Registering
3CX PBX v12.5. SIP Trunking using the Optimum Business Sip Trunk Adaptor and the 3CX PBX v12.5
SIP Trunking using the Optimum Business Sip Trunk Adaptor and the 3CX PBX v12.5 Table of Contents 1. Overview 3 2. Prerequisites 3 3. PBX Configuration 3 4. Creating Extensions 4 5. VoIP Provider Setup
Configuring the Dolby Conference Phone with Cisco Unified Communications Manager
Configuring the Dolby Conference Phone with Cisco Unified Communications Manager Version 1.2 December 10, 2015 This product is protected by one or more patents in the United States and elsewhere. For more
LifeSize Video Communications Systems Administrator Guide
LifeSize Video Communications Systems Administrator Guide November 2009 Copyright Notice 2005-2009 LifeSize Communications Inc, and its licensors. All rights reserved. LifeSize Communications has made
Analog Telephone Adapter Network settings via Keypad commands:
Analog Telephone Adapter Network settings via Keypad commands: The ATA series phone adapters (VIP-156/VIP-156PE/VIP-157/VIP-157S) support telephone keypad configurations, please connect analog telephone
Prestige 2302R Series
VoIP Station Gateway Quick Start Guide Version 3.60 6/2005 Overview This Quick Start Guide covers the Prestige (P2302R) and (P2302RL) models. It explains how to use your Prestige to make phone calls through
Ithaca itherm, POSjet & BANKjet Printers Ethernet Adapters Setup Guide
Ithaca itherm, POSjet & BANKjet Printers Ethernet Adapters 100-05203 Rev A 4/26/04 Contents Contents... 2 Ethernet Connection... 3 Configuration... 4 Locator Program... 4 Installation... 4 Using Locator...
How To Check If Your Router Is Working Properly On A Nr854T Router (Wnr854) On A Pc Or Mac) On Your Computer Or Ipad (Netbook) On An Ipad Or Ipa (Networking
Chapter 7 Using Network Monitoring Tools This chapter describes how to use the maintenance features of your RangeMax NEXT Wireless Router WNR854T. These features can be found by clicking on the Maintenance
How to Configure the Avaya IP Office 6.1 for use with Integra Telecom SIP Solutions
How to Configure the Avaya IP Office 6.1 for use with Integra Telecom SIP Solutions Overview This document provides a reference for configuration of the Avaya IP Office to connect to Integra Telecom SIP
AP6511 First Time Configuration Procedure
AP6511 First Time Configuration Procedure Recommended Minimum Configuration Steps From the factory, all of the 6511 AP s should be configured with a shadow IP that starts with 169.254.xxx.xxx with the
Configuration Notes 290
Configuring Mediatrix 41xx FXS Gateway with the Asterisk IP PBX System June 22, 2011 Proprietary 2011 Media5 Corporation Table of Contents Introduction... 3 About Mediatrix 41xx Series FXS Gateways...
Chapter 6 Using Network Monitoring Tools
Chapter 6 Using Network Monitoring Tools This chapter describes how to use the maintenance features of your Wireless-G Router Model WGR614v9. You can access these features by selecting the items under
D-Link DAP-1360 Repeater Mode Configuration
D-Link DAP-1360 Repeater Mode Configuration Outline 1. Package Contents 2. System Requirements 3. Hardware Overview Connections LED s WPS LED/Button 4. Default Settings 5. Configuring your LAN Adapter
NET UX Series with Microsoft Lync 2010 and CyberData VoIP Intercom
Network Equipment Technologies, Inc. NET UX Series with Microsoft Lync 2010 and CyberData VoIP Intercom Configuration Note Rushal Patel Table of Contents 1. Introduction... 3 2. Assumptions and Prerequisites...
Chapter 1 Configuring Internet Connectivity
Chapter 1 Configuring Internet Connectivity This chapter describes the settings for your Internet connection and your wireless local area network (LAN) connection. When you perform the initial configuration
Quick Installation Guide
Quick Installation Guide MegaPBX Version 2.1 Quick Installation Guide v2.1 www.allo.com 2 Table of Contents Initial Setup of MegaPBX... 4 Notification LEDs (On the Front Panel of the Gateway)... 5 Create
PePWave Surf Series PePWave Surf Indoor Series: Surf 200, AP 200, AP 400
PePWave Surf Series PePWave Surf Indoor Series: Surf 200, AP 200, AP 400 PePWave Surf Outdoor Series: Surf AP 200/400-X, PolePoint 400-X, Surf 400-DX User Manual Document Rev. 1.2 July 07 COPYRIGHT & TRADEMARKS
SIP Trunking using the EdgeMarc Network Services Gateway and the Mitel 3300 ICP IP-PBX
June 26th, 2014 SIP Trunking using the EdgeMarc Network Services Gateway and the Mitel 3300 ICP IP-PBX Page 1 of 30 Table of Contents 1 Overview... 3 2 Prerequisites... 3 3 Network Topology... 4 4 Description
Installation of the On Site Server (OSS)
Installation of the On Site Server (OSS) rev 1.1 Step #1 - Initial Connection to the OSS Having plugged in power and an ethernet cable in the eth0 interface (see diagram below) you can connect to the unit
V101 SIP VoIP Telephone Adaptor User Manual V1.1m
V101 SIP VoIP Telephone Adaptor User Manual V1.1m Quick Guide Step 1: Broadband (ADSL/Cable Modem) Connections for V101 A. Connect V101 LAN port to ADSL NAT Router as the following connection. B. Connect