Installation Instructions Honeywell Air Sampling Smoke Detection System Honeywell HI-SPEC

Transcription

1 Installation Instructions Honeywell Air Sampling Smoke Detection System Honeywell HI-SPEC 0 9 Operating-indicator light Indicator light for fault Indicator light for alert alarm-detector module I Indicator light for action alarm-detector module I Indicator light for fire alarm-detector module I Smoke level display to 0 for detector module I Indicator light for alert alarm-detector module II Indicator light for action alarm-detector module II 9 Indicator light for fire alarm-detector module II 0 Smoke level display to 0 for detector module II Pre-punched cable entries for connection to the central fire panel or power supply (input/output) Connection pipe system I Connection pipe system II Connection for air return HI-SPEC unit_hon.doc 0/0 of

2 S F O 9 Installation of the Detector Module Please note: - Only the detector modules of the type ASD-TT-0, ASD-TT-0 and ASD-TT-00 - that have been approved by the VdS-certification authority may be used. - Carry out the following works only if the device is powered down.. Open the device by carefully unlocking the housing snap-in closures by means of a screwdriver. Then lift the housing lid a little bit.. Carefully pull the connection cable of the display board off (connection Display ) and remove the housing lid. Note: Shall the device only be provided with one detector module, please skip to point. Shall the device however be provided with two detector modules please follow the following instructions.. Recover carefully the ventilator cover for the second air sampling duct (self-adhesive plastic cover).. Break carefully the clasp for the connection of the second pipe system (predetermined breaking point, marked by II ) with a screwdriver from the housing. Note: The knockout is to be removed completely from the device.. Make the required settings by setting the contacts of switch S accordingly (see also Settings of the detector module ).. Fix the detector module in the corresponding mounting position.. Ensure the detector is fully clipped home. Connect the detector module via the ribbon cable with the connection Head (detector module I) or Head (detector module II) to the base board. Note the labelling of the base board. 9. Reconnect the display board to the base board (connection Display ). Note the labelling of the base board. HI-SPEC unit_hon.doc 0/0 of

3 Detector Module Settings In the following tables of the switch positions S have positions. on off The standard settings have a grey background. Setting the response sensitivity detector module DM-TT- 0 DM-TT- 0 DM-TT- 0 S. S. 0, %/m 0, %/m on on 0, %/m 0,0 %/m off on,0 %/m 0, %/m 0,0 %/m on off 0, %/m 0, %/m 0,0%/m off off Setting the alarm delay S. S. 0 seconds off off 0 seconds on off 0 seconds off on 0 seconds on on Setting the activating threshold air flow fault S. S. small on off medium off on large off off very large on on Setting the delay air flow fault S. S. 0. minutes off on minutes on off minutes on on 0 minutes off off Setting the fault signal S. 9 non-latched latched off on Setting LOGIC SENS S.0 off on off on HI-SPEC unit_hon.doc 0/0 of

4 HEAD DIAG HEAD DISPLAY CUTOFF HEAD DIAG BR BR X F X X X BR X BR Br Br BR BR SCI ITAG BR Br Br BrBr BR Choose number of the detector modules The number of detector modules is chosen with the jumper BR. The following table shows, whether the jumper must be put or not: X = pin pair bridge O = pin pair open The standard settings have a grey background. Choose number of the detector modules Bridge Pin No. BR, + detector module X detector module O Setting the ventilator voltage Jumper BR on the base board and Jumper BR on the additional board allows the setup of the ventilator voltage. The following table shows whether the jumpers are set or not: X = pin pair bridge O = pin pair open The standard settings have a grey background. Setting the ventilator voltage baseboard additional board Jumper Pin No. BR + BR + BR +, V O O X,9 V O X O 9 V O O O HI-SPEC unit_hon.doc 0/0 of

5 JU JU K K JU JU K K X K JU- JU X JU JU JU JU X K K X JU JU K K JU JU JU JU X X9 X0 X X Setting the function of the collective fault contact The contact type (break contact or make contact) of the collective fault is set using the jumper JU and JU. collective fault contact detector module I = Jumper JU collective fault contact detector module II = Jumper JU The following table shows the positioning of the jumpers: X = pin pair bridge O = pin pair open The standard settings have a grey background. Setting the collective fault contact Jumper Pin No. JU/ + JU/ + break contact O X make contact X O HI-SPEC unit_hon.doc 0/0 of

6 Setting the alarm contacts The contact type (break contact or make contact) of the alarm contacts is set using the jumper JU to JU. Alarm contact alert alarm detector module I = Jumper JU Alarm contact alert alarm detector module II = Jumper JU Alarm contact action alarm detector module I= Jumper JU Alarm contact action alarm detector module II = Jumper JU Alarm contact fire alarm detector module I = Jumper JU Alarm contact fire alarm detector module II = Jumper JU The following table shows the positioning of the jumpers: X = pin pair bridge O = pin pair open The standard settings have a grey background. Setting the alarm contacts Jumper Pin-No. JU- + JU- + break contact O X make contact X O A B Device Supports A Support Type MT- horizontal installation B Support Type MT- vertical installation HI-SPEC unit_hon.doc 0/0 of

7 Installation of the device General information: - When choosing the installation location make sure the displays of the device are clearly visible. - Screw the air sampling smoke detection system either directly to the wall with its bottom casing or mount it by means of a special support (type MT-). This support allows to mount the device also to racks for example. - The air outlet of the device must not be blocked. (The distance between the air outlet and adjacent objects (e.g. wall) is to be at least 0 cm.) - The air sampling smoke detection system can be mounted with the air sampling pipe connector(s) pointing upwards or downwards. (If necessary, turn the lid by 0 ). If the air sampling pipe connector(s) point downwards make sure no impurities enter the air outlet which then points upwards. - At switching-on the supply voltage, the device does not start running at once but only after approx. 0 seconds. Procedure:. First, clearly mark the fixing points for mounting the device. If necessary, use the provided drilling jig. Fix the device using four screws (max. of mm for wall mounting and max. of mm for mounting by means of the device support MT-) in order to guarantee a safe fixing and to limit vibrations which occur.. Fix the device by means of four screws in accordance with the mounting type to the wall or the device support. Make sure the device is not fixed under mechanical tension or the screws are not tightened too much. Otherwise the device might be damaged, or unintended secondary noise may arise. Note: To balance unevenness and/or to avoid vibrations vibration dampers need to be installed.. Carefully break out of the housing the required cable entries (max. x M0 und x M). If required, use a screwdriver.. Carefully equip the cable entry(entries) according to requirements with M0 or M glands (x M, x M0 included in the delivery) by inserting them into the corresponding cable entry/entries.. Pass the connection cable(s) (max.. mm²) required to wire the device through the prepared M0 or M glands into the device and cut it to the required length within the device.. Wire the device according to the following connection diagram. HI-SPEC unit_hon.doc 0/0 of

8 connection to central fire panel internal connection connection board internal connection connection board Parallelanzeige +V 0V +V 0V +V 0V +V 0V +V 0V X X X0 X9 X + _ + _ V für Display Display Data + V _ + Alt.Sens. _ + Reset _ X X X K JU K JU K JU RF I RA I RA I X X X X X X fault contact Action alarm-relay Alert alarm-relay detector module I +V 0V L+ L+ L+ L+ L+ L+ L- L- L- L- L- L- X X K JU K JU RA I RF II X X X X fault contact Fire alarm-relay L+ L+ L+ L+ L+ L+ L+ L+ L+ L+ L- L- L- L- L- L- L- L- L- L- X X X K JU K JU K JU RA II RA II RA II X X X X X X Fire alarm-relay Action alarm-relay Alert alarm-relay detector module II HI-SPEC unit_hon.doc 0/0 of

9 Connections X + X + X + X + X + X + X + X + X / X / X / X / X / X / X / X / X / X / X / X / X / X / X / X / / / / / Fault resistance for fault contact II (just to connect, if the contact as normally open programmed is, no standard) alarm resistance for alarm contact alert alarm II (just to connect, if the contact as normally open programmed is, standard) alarm resistance for alarm contact action alarm II (just to connect, if the contact as normally open programmed is, standard) alarm resistance for alarm contact fire alarm II (just to connect, if the contact as normally open programmed is, standard) Fault resistance for fault contact I (just to connect, if the contact as normally open programmed is, no standard) alarm resistance for alarm contact alert alarm I (just to connect, if the contact as normally open programmed is, standard) alarm resistance for alarm contact action alarm I (just to connect, if the contact as normally open programmed is, standard) alarm resistance for alarm contact fire alarm I (just to connect, if the contact as normally open programmed is, standard) + output line Fault II - output line Fault II + output line Alert alarm II - output line Alert alarm II + output line Action alarm II - output line Action alarm II + output line Fire alarm II - output line Fire alarm II + output line Fault I - output line Fault I + output line Alert alarm I - output line Alert alarm I + output line Action alarm I - output line Action alarm I + output line Fire alarm I - output line Fire alarm I + input line Fault II - input line Fault II + input line Alert alarm II - input line Alert alarm II HI-SPEC unit_hon.doc 0/0 9 of

10 / / / / / / / / / / / / X / X / X / X / X9 / X9 / X9 / X9 / X0 / X0 / X0 / X0 / X / X / X / X / + input line Action alarm II - input line Action alarm II + input line Fire alarm II - input line Fire alarm II + input line Fault I - input line Fault I + input line Alert alarm I - input line Alert alarm I + input line Action alarm I - input line Action alarm I + input line Fire alarm I - input line Fire alarm I + V reset input 0 V reset input + V reset output 0 V reset output + V input Alt. Sens. Alternate Sensitivity 0 V input Alt. Sens. Alternate Sensitivity + V output Alt. Sens. Alternate Sensitivity 0 V output Alt. Sens. Alternate Sensitivity + V supply voltage 0 V supply voltage + V supply voltage 0 V supply voltage + data external Display - data external Display + V external Display 0 V external Display HI-SPEC unit_hon.doc 0/0 0 of

11 S OFF S Flow-Init Commissioning. Switch on the voltage supply (v) Note: The fan starts running seconds after switching on the voltage supply ( V). Commissioning. Make sure first that the device has been in operation for at least 0 minutes prior to the air flow initialization in order to reach the operating temperature.. In order to initialize the connected pipe system, press the Flow-Init-button S (see figure) of the corresponding detector module until the green operating-indicator light of the device starts flashing. The initialization is terminated after approx. seconds. After a successful initialization the operating- indicator light is lit permanently.. During and after initialization the pipe system must no longer be changed. Even the ventilator voltage of the device must no longer be modified after initializations. Otherwise the initialization must be carried out again. HI-SPEC unit_hon.doc 0/0 of

12 Certificate of Conformity pursuant to EU Construction Products Directive 9/0/EEC The conformity of the air sampling smoke detector for fire detection and fire alarm systems in buildings according to DIN EN -0 has been established by a test at the VdS laboratory. The EC certificate of conformity has been issued by notified product certification body (ID no. 0, VdS). The CE designation according to DIN EN -0 has been carried out. 0 WAGNER Group GmbH Schleswigstrasse - 0 Langenhagen 09 Nr. 0 CPD 0 EN -0: 00 Air sampling smoke detector for fire detection and fire alarm systems in buildings 0,0 % light obscuration/m Class: A, B and C 0, % light obscuration/m Class: A, B and C 0, % light obscuration/m Class: A, B and C Honeywell Life Safety Systems 0 Waterside Road Hamilton Industrial Park Leicester LE TN Tel (+) 000 HI-SPEC unit_hon.doc 0/0 of