MCP6001/1R/1U/2/4. 1 MHz, Low-Power Op Amp. Features. Description. Applications. Package Types. Design Aids. Typical Application

Transcription

1 MCP600/R/U// MHz, LowPower Op Amp Features Available in SC705 and SOT5 packages Gain Bandwidth Product: MHz (typical) RailtoRail Input/Output Supply Voltage:.8V to 6.0V Supply Current: I Q = 00 µa (typical) Phase Margin: 90 (typical) Temperature Range: Industrial: 0 C to 85 C Extended: 0 C to 5 C Available in Single, Dual and Quad Packages Applications Automotive Portable Equipment Photodiode Amplifier Analog Filters Notebooks and PDAs BatteryPowered Systems Design Aids SPICE Macro Models FilterLab Software Mindi Circuit Designer & Simulator Microchip Advanced Part Selector (MAPS) Analog Demonstration and Evaluation Boards Application Notes Typical Application R V REF R MCP600 R Gain = R Description The Microchip Technology Inc. MCP600// family of operational amplifiers (op amps) is specifically designed for generalpurpose applications. This family has a MHz Gain Bandwidth Product (GBWP) and 90 phase margin (typical). It also maintains 5 phase margin (typical) with a 500 pf capacitive load. This family operates from a single supply voltage as low as.8v, while drawing 00 µa (typical) quiescent current. Additionally, the MCP600// supports railtorail input and output swing, with a common mode input voltage range of 00 mv to 00 mv. This family of op amps is designed with Microchip s advanced CMOS process. The MCP600// family is available in the industrial and extended temperature ranges, with a power supply range of.8v to 6.0V. Package Types MCP600 SC705, SOT5 MCP600R SOT5 MCP600U SOT A MCP600 PDIP, SOIC, MSOP A A MCP600 PDIP, SOIC, TSSOP A A A D D D B 5 0 C B B C C B B B NonInverting Amplifier 008 Microchip Technology Inc. DS7Hpage

2 MCP600/R/U//.0 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings...7.0V Current at Analog Input Pins (, )...± ma Analog Inputs (, )....0Vto.0V All Other Inputs and Outputs... 0.V to 0.V Difference Input Voltage... Output Short Circuit Current...Continuous Current at Output and Supply Pins...±0 ma Storage Temperature C to 50 C Maximum Junction Temperature (T J )...50 C ESD Protection On All Pins (HBM; MM)... kv; 00V Notice: Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. See Section.. Input Voltage and Current Limits. DC ELECTRICAL SPECIFICATIONS Electrical Characteristics: Unless otherwise indicated, T A = 5 C, =.8V to 5.5V, = GND, V CM = /, V L = /, R L = 0 kω to V L, and / (refer to Figure and Figure ). Input Offset Input Offset Voltage V OS.5.5 mv V CM = (Note ) Input Offset Drift with Temperature ΔV OS /ΔT A ±.0 µv/ C T A = 0 C to 5 C, V CM = Power Supply Rejection Ratio PSRR 86 db V CM = Input Bias Current and Impedance Input Bias Current: I B ±.0 pa Industrial Temperature I B 9 pa T A = 85 C Extended Temperature I B 00 pa T A = 5 C Input Offset Current I OS ±.0 pa Common Mode Input Impedance Z CM 0 6 Ω pf Differential Input Impedance Z DIFF 0 Ω pf Common Mode Common Mode Input Range V CMR V Common Mode Rejection Ratio CMRR db V CM = 0.V to 5.V, = 5V OpenLoop Gain DC OpenLoop Gain (Large Signal) A OL 88 db = 0.V to 0.V, V CM = Output Maximum Output Voltage Swing V OL, V OH 5 5 mv = 5.5V, 0.5V Input Overdrive Output Short Circuit Current I SC ±6 ma =.8V ± ma = 5.5V Power Supply Supply Voltage V Note Quiescent Current per Amplifier I Q µa I O = 0, = 5.5V, V CM = 5V Note : MCP600/R/U// parts with date codes prior to December 00 (week code 9) were tested to ±7 mv minimum/ maximum limits. : All parts with date codes November 007 and later have been screened to ensure operation at = 6.0V. However, the other minimum and maximum specifications are measured at.8v and 5.5V. DS7Hpage 008 Microchip Technology Inc.

3 MCP600/R/U// AC ELECTRICAL SPECIFICATIONS Electrical Characteristics: Unless otherwise indicated, T A = 5 C, =.8 to 5.5V, = GND, V CM = /, V L = /, /, R L = 0 kω to V L, and C L = 60 pf (refer to Figure and Figure ). AC Response Gain Bandwidth Product GBWP.0 MHz Phase Margin PM 90 G = V/V Slew Rate SR 0.6 V/µs Noise Input Noise Voltage E ni 6. µvpp f = 0. Hz to 0 Hz Input Noise Voltage Density e ni 8 nv/ Hz f = khz Input Noise Current Density i ni 0.6 fa/ Hz f = khz TEMPERATURE SPECIFICATIONS Electrical Characteristics: Unless otherwise indicated, =.8V to 5.5V and = GND. Temperature Ranges Industrial Temperature Range T A 0 85 C Extended Temperature Range T A 0 5 C Operating Temperature Range T A 0 5 C Note Storage Temperature Range T A C Thermal Package Resistances Thermal Resistance, 5LSC70 θ JA C/W Thermal Resistance, 5LSOT θ JA 56 C/W Thermal Resistance, 8LPDIP θ JA 85 C/W Thermal Resistance, 8LSOIC (50 mil) θ JA 6 C/W Thermal Resistance, 8LMSOP θ JA 06 C/W Thermal Resistance, LPDIP θ JA 70 C/W Thermal Resistance, LSOIC θ JA 0 C/W Thermal Resistance, LTSSOP θ JA 00 C/W Note: The industrial temperature devices operate over this extended temperature range, but with reduced performance. In any case, the internal Junction Temperature (T J ) must not exceed the Absolute Maximum specification of 50 C.. Test Circuits The test circuits used for the DC and AC tests are shown in Figure and Figure. The bypass capacitors are laid out according to the rules discussed in Section. Supply Bypass. / R N 0. µf µf MCP600X 0. µf µf R G R F C L R L / R N R G MCP600X R F C L R L FIGURE : AC and DC Test Circuit for Most Inverting Gain Conditions. V L V L FIGURE : AC and DC Test Circuit for Most NonInverting Gain Conditions. 008 Microchip Technology Inc. DS7Hpage

4 MCP600/R/U// N b E E e e D A A c φ A L L 008 Microchip Technology Inc. DS7Hpage 7

5 MCP600/R/U// PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO. X /XX Device Temperature Range Package Device: MCP600T: Single Op Amp (Tape and Reel) (SC70, SOT) MCP600RT: Single Op Amp (Tape and Reel) (SOT) MCP600UT: Single Op Amp (Tape and Reel) (SOT) MCP600: Dual Op Amp MCP600T: Dual Op Amp (Tape and Reel) (SOIC, MSOP) MCP600: Quad Op Amp MCP600T: Quad Op Amp (Tape and Reel) (SOIC, MSOP) Temperature Range: I = 0 C to 85 C E = 0 C to 5 C Package: LT = Plastic Package (SC70), 5lead (MCP600 only) OT = Plastic Small Outline Transistor (SOT), 5lead (MCP600, MCP600R, MCP600U) MS = Plastic MSOP, 8lead P = Plastic DIP (00 mil body), 8lead, lead SN = Plastic SOIC, (.99 mm body), 8lead SL = Plastic SOIC (.99 body), lead ST = Plastic TSSOP (.mm body), lead Examples: a) MCP600TI/LT: Tape and Reel, 5LD SC70 package b) MCP600TI/OT: Tape and Reel, 5LD SOT package. c) MCP600RTI/OT: Tape and Reel, 5LD SOT package. d) MCP600UTE/OT: Tape and Reel, Extended Temperature, 5LD SOT package. a) MCP600I/MS: 8LD MSOP package. b) MCP600I/P: 8LD PDIP package. c) MCP600E/P: Extended Temperature, 8LD PDIP package. d) MCP600I/SN: 8LD SOIC package. e) MCP600TI/MS: Tape and Reel, 8LD MSOP package. a) MCP600I/P: LD PDIP package. b) MCP600I/SL: LD SOIC package. c) MCP600E/SL: Extended Temperature, LD SOIC package. d) MCP600I/ST: LD TSSOP package. e) MCP600TI/SL: Tape and Reel, LD SOIC package. f) MCP600TI/ST: Tape and Reel, LD TSSOP package. 008 Microchip Technology Inc. DS7Hpage 7