Board Mount Connector Footprint Design Process
|
|
- Andra Poole
- 7 years ago
- Views:
Transcription
1
2 Board Mount Connector Footprint Design Process STEP 1: Connector Selection Series Force to Engage (Max) Max SB LD FD Freq. SMP 2.0 lbs 10 lbs 15 lbs 40 GHz SMPM 3.5 lbs N/A 8.0 lbs 65 GHz SMPS 3.0 lbs N/A 4.0 lbs 100 GHz Select connector series and type based on performance requirements and packaging constraints Example Connector Selection: 2X Series Force to Disengage (Min) SB LD FD SMP 8 oz 2.0 lbs 5.0 lbs SMPM 10 oz N/A 3.0 lbs SMPS 7 oz N/A 2.0 lbs X X Series Mating Cycles (Min) SB LD FD SMP SMPM 500 N/A 100 SMPS 500 N/A 100 4X SB = Smooth Bore, LD = Limited Detent, FD = Full Detent STEP 2: PCB Definition Foil Surface Layer E MIL Megtron 6 Layer 6.57 MIL Foil Reference Layer E MIL PCB Side View All other layers Provide PCB Characteristics to the SV Microwave Team to begin simulation and optimization (see pages 15 & 16 for more information) 2
3 Board Mount Connector Footprint Design Process STEP 3: Footprint Design.085± ±0.05 2X MOUNTING THRU HOLES 13X PLATED THRU HOLES ± ± TYP TYP. 2X FOIL REFERENCE LAYER E2 2X SV Engineering develops customized PCB launch footprint based on design parameters of connector and PCB materials STEP 4: Simulation and Optimization VSWR Improvement over connector launch with Successive Design Iterations TDR Improvement over connector launch with Successive Design Iterations 3
4 Simulated vs. Measured Test Results Simulated VSWR for cabled connector launching to PCB closely matches lab tested results Thru-Hole SMP matched to Co-planar Waveguide in simulation software Surface Mount SMPM matched to Co-planar Waveguide in simulation software Measured 1.45 Measured 1.40 Simulated 1.40 Simulated VSWR 1.25 VSWR Frequency (GHz) Frequency (GHz) Simulated vs. Measured Results for Thru-Hole SMP Simulated vs. Measured Results for Surface Mount SMPM Electrical current loss through the launch minimized by matching trace and grounding pads to RF connector to ensure 50 ohm impedance throughout the system 4
5 SMP Series Board Mount Connectors SMP Edge Launch Male SB LD FD * CM * Note: Dimensions on Catchers Mitt do not match image shown in catalog SMP 2 Port Edge Launch Male SB LD FD SMP 4 Port Edge Launch Male SB LD FD 5
6 SMP Series Board Mount Connectors SMP Thru-Hole Male with Right Angle Contact SF SF SF Detent SB LD FD SMP 2 Port Thru-Hole Male with Right Angle Contact SB LD FD SMP 4 Port Thru-Hole Male with Right Angle Contact SB LD FD 6
7 SMP Series Board Mount Connectors SMP Thru-Hole Male with Right Angle Body SMP 2 Port Thru-Hole Male with Right Angle Body SF SF SF Detent SB LD FD SMP 4 Port Thru-Hole Male with Right Angle Body SF SF SF Detent SB LD FD SF SF SF Detent SB LD FD 7
8 SMP Series Board Mount Connectors SMP Edge Launch Male (custom PCB thickness) SB LD FD SMP Surface Mount Male with Right Angle Contact SB LD FD SMP Thru-Hole Male SF SF SF Detent SB LD FD 8
9 SMPM Series Board Mount Connectors SMPM Edge Launch Male FD SB SMPM 2 Port Edge Launch Male SB FD SMPM 4 Port Edge Launch Male SB FD 9
10 SMPM Series Board Mount Connectors SMPM Thru-Hole Male with Right Angle Body FD SB SMPM 2 Port Thru-Hole Male with Right Angle Body SF SF Detent SB FD SMPM 4 Port Thru-Hole Male with Right Angle Body SF SF Detent SB FD 10
11 SMPM Series Board Mount Connectors SMPM Thru-Hole Male with Right Angle Contact SF SF Detent FD SB SMPM 2 Port Thru-Hole Male with Right Angle Contact SB FD SMPM 4 Port Thru-Hole Male with Right Angle Contact SB FD 11
12 SMPM Series Board Mount Connectors SMPM Thru-Hole Female (Compliant Pin) SMPM Surface Mount Male with Right Angle Contact FD SB SMPM Thru-Hole Male FD SB 12
13 Hermetic Board Mount Connectors SMP Surface Mount Male with Glass Seal SB LD FD SMPM Surface Mount Male with Glass Seal SB FD SMPS Surface Mount Male with Glass Seal SB FD 13
14 SMPS Series Board Mount Connectors SMPS Surface Mount Male with Loose Contact SB FD SMPS Edge Launch Male X X X SB FD SMPS Surface Mount Male SB FD 14
15 Board Mount Connector Spec Request Form (Additional Copies Available on Website) Centrepark West Drive, Suite 100 West Palm Beach, FL Phone: (561) Fax: (561)
16 Board Mount Connector Spec Request Form Centrepark West Drive, Suite 100 West Palm Beach, FL Phone: (561) Fax: (561)
SMA Interface Mating Dimensions (Per MIL-STD-348)
SMA Series SMA 6 SMA Interface Mating Dimensions (Per MIL-STD-348) SMA Interface Dimensions MALE Inches/Millimeters 3 Minimum Nominal Maximum LTR in. mm in. mm in. mm A.250 6.35.263 6.68.. B.1790 4.55.1808
More informationSMA Connectors. RF Coax Connectors. Product Facts
SMA Connectors Product Facts Performance to 12.4 GHz and beyond Available in various base metal options, including stainless steel, brass and zinc diecast Uses industry standard crimp tools and processes
More informationThe Design & Test of Broadband Launches up to 50 GHz on Thin & Thick Substrates
The Performance Leader in Microwave Connectors The Design & Test of Broadband Launches up to 50 GHz on Thin & Thick Substrates Thin Substrate: 8 mil Rogers R04003 Substrate Thick Substrate: 30 mil Rogers
More informationIndex. 2.40 mm Connector Series. 2.40 mm Connectors (50 GHz)... Page. Interface Standards... 44. Specifications... 45. Connector Numbers...
Connector Series Index (50 GHz).... Page Interface Standards... 44 Specifications... 45 Connector Numbers... 46 Typical Test Data... 48 End : can be found in the Adapter section. : can be found in the
More informationConnector Launch Design Guide
WILD RIVER TECHNOLOGY LLC Connector Launch Design Guide For Vertical Mount RF Connectors James Bell, Director of Engineering 4/23/2014 This guide will information on a typical launch design procedure,
More informationBetween Series Adapters
Between Series Adapters Between Series Coaxial Transmission Line Adapters provide convenient transitions between popular series coaxial connectors. The adapter design provides a minimum length consistent
More informationHow to make a Quick Turn PCB that modern RF parts will actually fit on!
How to make a Quick Turn PCB that modern RF parts will actually fit on! By: Steve Hageman www.analoghome.com I like to use those low cost, no frills or Bare Bones [1] type of PCB for prototyping as they
More informationANOISON HPQN SERIES HPQN CONNECTORS INTERFACE DIMENSIONS. Description. Interface Dimensions 21 Characteristics
SERIES HPQN CONNECTORS DESCRIPTION CONTENT Designed by James Qu at Anoison in 2006, the HPQN is a quick locking version of the widely used type N connector. By replacing the threaded interface of the original
More informationConnectivity in a Wireless World. Cables Connectors 2014. A Special Supplement to
Connectivity in a Wireless World Cables Connectors 204 A Special Supplement to Signal Launch Methods for RF/Microwave PCBs John Coonrod Rogers Corp., Chandler, AZ COAX CABLE MICROSTRIP TRANSMISSION LINE
More informationOutside Plant Precision Cooling Site Monitoring and Services
Emerson Network Power Connectivity Solutions Johnson 299 Johnson Avenue Waseca, MN 56093 USA Tel: 800.247.8256 Fax: 507.833.6287 www.emersonnetworkpower.com/connectivity About Emerson Network Power Connectivity
More informationSMZ type 43 INTRODUCTION. The Radiall Type 43 coaxial connector range. Type 43 series - Features and benefits
INTRODUCTION The Radiall Type 43 coaxial connector range The Radiall range of Type 43 series connectors is fully approved (where applicable) to BT (British Telecom) standards as well as to British Standard
More informationW1 Connector W1 Adapter W1 Termination
Data Sheet W1 Connector W1 Adapter W1 Termination DC to 110 GHz A complete coaxial connector system with mode-free performance to 110 GHz Features Excellent RF Performance to 110 GHz 50Ω Impedance Low
More informationAntenna Part Number: FR05-S1-R-0-105
Fractus EZConnect Zigbee, RFID, ISM868/9 Chip Antenna Antenna Part Number: FR5-S1-R--15 This product is protected by at least the following patents PAT. US 7,148,85, US 7,22,822 and other domestic and
More informationGeneral Information. Lower Frequency Models Custom Designs Special Flanges Narrow Band Specials VSWR. Frequency ( GHz) COMMON SPECIFICATIONS
Waveguide Adapters General Information DC - 26.5 GHz High Performance 1.15 Typical VSWR Male or Female Connectors available Choke Flange Types available -65 o C to +125 o C Operating Temperature Midwest
More informationMAPD-007530-0001TB. Low Cost Two-Way GMIC SMT Power Divider 1700 2000 MHz Rev. V2. Features. Functional Diagram. Description. Ordering Information
Features Small Size and Low Profile Typical Insertion Loss: 0.6 db Typical Amplitude Balance: 0.2 db 1 Watt Power Handling Lead-Free SOT-26 Package 100% Matte Tin Plating over Copper Halogen-Free Green
More informationFakra. Coaxial connectors. DC 6 GHz
C-Blue D-Bordeaux GPS application GSM/Mobil Phone The FAKRA (Automobile Expert Group) has therefore defined a standardised connector system for the various communication applications in cars. Our FAKRA-compliant
More informationTimes Microwave Systems Hermetically Sealed Assemblies
SCOPE This Specification details the Electrical, Mechanical and Environmental Characteristics of Times Microwave Systems MILTECH 340.34 Diameter Hermetically Sealed Coaxial Transmission Lines. This product
More informationPRODUCT SPECIFICATION
ipass TM / ipass+ TM 0.8 mm PITCH I/O CONNECTOR SYSTEM EXTERNAL ipass / ipass+ of TABLE OF CONTENTS.0 SCOPE... 3.0 PRODUCT DESCRIPTION... 3. PRODUCT NAME AND SERIES NUMBER(S)... 3. DIMENSION, MATERIALS,
More informationUtilizing Time Domain (TDR) Test Methods For Maximizing Microwave Board Performance
The Performance Leader in Microwave Connectors Utilizing Time Domain (TDR) Test Methods For Maximizing Microwave Board Performance.050 *.040 c S11 Re REF 0.0 Units 10.0 m units/.030.020.010 1.0 -.010 -.020
More information23-26GHz Reflective SP4T Switch. GaAs Monolithic Microwave IC in SMD leadless package
CHS2411-QDG Description GaAs Monolithic Microwave IC in SMD leadless package The CHS2411-QDG (CHS2412-QDG, see Note) is a monolithic reflective SP4T switch in K-Band. Positive supply voltage only is required.
More informationUSB 3.0 INTERNAL CONNECTOR AND CABLE SPECIFICATION
USB 3.0 INTERNAL CONNECTOR AND CABLE SPECIFICATION Revision 1.0 August 20, 2010 2007-2010 Intel Corporation All rights reserved. Legal Disclaimers THIS SPECIFICATION IS PROVIDED AS IS WITH NO WARRANTIES
More informationCinch Connectivity Solutions. High Frequency End Launch Connectors
Cinch Connectivity Solutions High Frequency End Launch Connectors Applications High Frequency SMA End Launch Connectors For Microwave PC Board Substrates The Johnson Patent Pending High Frequency End Launch
More informationwww.tvsat.com.pl COAXICON Series Mobile Phone Switching Coax Connectors RF Coax Connectors Product Facts
COXICON Series Mobile Phone Switching Coax Connectors Product Facts ble to switch RF signal from internal to external antenna SMD component for standard pick & place Up to 2.4 GHz Up to 30,000 life cycles
More informationFractus Compact Reach Xtend
Fractus Compact Reach Xtend Bluetooth, Zigbee, 82.11 b/g/n WLAN Chip Antenna Antenna Part Number: FR5-S1-N--12 This product is protected by at least the following patents PAT. US 7,148,85, US 7,22,822
More informationMAURY. VNA Calibration Kits, Microwave Components & Adapters. Calibrate With Confidence IN THIS CATALOG:
MAURY VNA Calibration Kits, Microwave Components & Adapters IN THIS CATALOG: VNA Calibration Kits Calibration Standards Coaxial & Waveguide Adapters Connector Gage Kits Air Lines Torque Wrenches Manual
More informationJack to Jack adapters Plug to Plug U-Link connectors PCB Right angle plastic PCB Right angle - metal. Ordering Codes
BNC 75Ω RF CONNECTORS BNC 75Ω RF CONNECTORS To meet the need for higher performance, impedance matched cable interconnections, Amphenol offers a full line of 75 ohm BNC connectors. These connectors can
More informationTest Cable Assemblies
Test Cable Assemblies and Coaxial Passive Components DC-65 GHz 8851 SW Old Kansas Ave. Stuart, FL 34997 USA +1-772-286-9300 +1-800-544-5594 sales@emc-rflabs.com www.emc-rflabs.com Premium Test Cable Lab-Flex
More information1000 Series Miniature Slide Switches
Miniature Switches Features/Benefits Variety of actuators and terminations Panel mount tabs available Epoxy terminal seal compatible with bottom-wash cleaning RoHS compliant Typical Applications Test &
More informationENGINEERING COMMITTEE
ENGINEERING COMMITTEE Interface Practices Subcommittee AMERICAN NATIONAL STANDARD ANSI/SCTE 02 2006 Specification for F Port, Female, Indoor NOTICE The Society of Cable Telecommunications Engineers (SCTE)
More informationRufa 2.4 GHz SMD Antenna Part No. 3030A5839 / 3030A5887 Product Specification
Product Specification 1 Features Designed for 2.4 GHz applications: Bluetooth, Wi-Fi (802.11b/g), ZigBee, etc. Easy to integrate Low profile design for use with no ground beneath the antenna High efficiency
More informationWaveguide Coaxial Transitions
Waveguide Coaxial Transitions Coaxial Adaptors RA SERIES The Waveguide Solution offers a standard range of Waveguide to Coaxial Adaptors. All designs have been optimised to offer high performance within
More informationMCR08B, MCR08M. Sensitive Gate Silicon Controlled Rectifiers. Reverse Blocking Thyristors. SCRs 0.8 AMPERES RMS 200 thru 600 VOLTS
MCR8B, MCR8M Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors PNPN devices designed for line powered consumer applications such as relay and lamp drivers, small motor controls,
More informationMASW-007070-0001TB. GaAs SPST Switch, Absorptive, Single Supply, DC-4.0 GHz. Features. Pin Configuration 1,2,3,4. Description. Ordering Information
Features Operates DC - 4 GHz on Single Supply ASIC TTL / CMOS Driver Low DC Power Consumption 50 Ohm Nominal Impedance Test Boards are Available Tape and Reel are Available Lead-Free 4 x 6 mm PQFN Package
More informationCapacitor Self-Resonance
Capacitor Self-Resonance By: Dr. Mike Blewett University of Surrey United Kingdom Objective This Experiment will demonstrate some of the limitations of capacitors when used in Radio Frequency circuits.
More informationMultilevel Socket Technologies
Multilevel Socket Technologies High Performance IC Sockets And Test Adapters Overview Company Overview Over 5,000 products High Performance Adapters and Sockets Many Custom Designs & Turn-Key Solutions
More informationMAGNETIC CARD READER DESIGN KIT TECHNICAL SPECIFICATION
MAGNETIC CARD READER DESIGN KIT TECHNICAL SPECIFICATION Part Number: 99821002 Rev 21 FEBRUARY 2011 REGISTERED TO ISO 9001:2008 1710 Apollo Court Seal Beach, CA 90740 Phone: (562) 546-6400 FAX: (562) 546-6301
More information(11) PCB fabrication / (2) Focused assembly
Company Fact Sheet TTM Technologies, Inc. is a world-wide leader in the manufacture of technologically advanced PCBs, backplane and sub-system assemblies. Our Global Presence / Local Knowledge approach
More informationHigh Frequency Ceramic Solutions
Page 1 of 6 General Specifications - Mounting Part Number 2450AT43A100 Frequency Range 2400-2500 Mhz Peak Gain 2.0 dbi typ. (-V) Average Gain 0.5 dbi typ. (-V) 9.5 db min. Input Power Impedance Operating
More informationPRINTED CIRCUIT BOARD DESIGN AND MANUFACTURING CORP.
PRINTED CIRCUIT BOARD DESIGN AND MANUFACTURING CORP. Corporate Information Established in 2004 Headquarter office in San Jose, CA Production factory located in Binh Duong, Vietnam - Center of hi-tech industrial
More informationNBB-402. RoHS Compliant & Pb-Free Product. Typical Applications
Typical Applications Narrow and Broadband Commercial and Military Radio Designs Linear and Saturated Amplifiers 0 RoHS Compliant & Pb-Free Product NBB-402 CASCADABLE BROADBAND GaAs MMIC AMPLIFIER DC TO
More informationFusca 2.4 GHz SMD Antenna
Product Specification 1 Features Designed for 2.4 GHz applications: Bluetooth, Wi-Fi (802.11a/b/g/n), ZigBee, etc. as well as 2.3 GHz WiMAX, 2.5 GHz WiMAX and WiBro. Easy to integrate Low profile design
More informationENGINEERING COMMITTEE Interface Practices Subcommittee AMERICAN NATIONAL STANDARD ANSI/SCTE 123 2011
ENGINEERING COMMITTEE Interface Practices Subcommittee AMERICAN NATIONAL STANDARD ANSI/SCTE 123 2011 Specification for F Connector, Male, Feed-Through NOTICE The Society of Cable Telecommunications Engineers
More informationSTANDARD MICRO-D CONNECTORS
STANDARD MICRO-D CONNECTORS RECTANGULAR CONNECTORS Pigtail connector - Metal shell.............................. 56 Pigtail connector - Low profile - Metal shell.................... 58 Pigtail connector
More informationFlexible Circuit Simple Design Guide
Flexible Circuit Simple Design Guide INDEX Flexible Circuit Board Types and Definitions Design Guides and Rules Process Flow Raw Material Single Side Flexible PCB Single Side Flexible PCB (Cover layer
More informationSMA Series Subminiature RF Connectors
SMA Series Subminiature RF Connectors Screw-on mating Frequency range DC-18 GHz High performance Rugged construction ONLINE CATALOG 104 John W. Murphy Drive P.O. Box 510 New Haven, CT 06513 www.aepconnectors.com
More informationHigh Speed Characterization Report
ECUE-E-12-XXX-T1-P2 Mated with: UEC5-019-1-H-D-RA-1-A Description: FireFly Equalized Micro Flyover System, 36 AWG Micro Twinax Ribbon Cable Samtec, Inc. 2005 All Rights Reserved Table of Contents Cable
More informationAnalog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK v2.71 HMC42ST8 / 42ST8E AMPLIFIER,.4-2.2
More informationProduct Name Hexa-Band Cellular SMD Antenna GSM / CDMA / DCS / PCS / WCDMA /UMTS /HSDPA / GPRS / EDGE 800 MHz to 2200 MHz
Anam PA.25a Specification Part No. PA.25a Product Name Anam Hexa-Band Cellular SMD Antenna GSM / CDMA / DCS / PCS / WCDMA /UMTS /HSDPA / GPRS / EDGE 800 MHz to 2200 MHz Feature High Efficiency Multi-Band
More informationPCB Antenna with Cable Integration Application Note Version 2
PCB Antenna with Cable Integration Application Note Version 2 CONTENTS 1. BASICS 2. APPLICATIONS 3. SIZE 4. SHAPE 5. GROUND PLANE SIZE 6. BANDWIDTH 7. VSWR 8. GAIN 9. EFFICIENCY 10. TECHNOLOGY ADVANTAGES
More informationMADP-000504-10720T. Non Magnetic MELF PIN Diode
MADP-54-172T Features High Power Handling Low Loss / Low Distortion Leadless Low Inductance MELF Package Non-Magnetic Surface Mountable RoHS Compliant MSL 1 Package Style 172 Dot Denotes Cathode Description
More informationDesigning a Schematic and Layout in PCB Artist
Designing a Schematic and Layout in PCB Artist Application Note Max Cooper March 28 th, 2014 ECE 480 Abstract PCB Artist is a free software package that allows users to design and layout a printed circuit
More informationHIGH REPEATABILITY SPDT, BROADBAND 12 GHZ MAGNETIC-LATCHING RF RELAY
HIGH REPEATABILITY SPDT, BROADBAND 12 GHZ MAGNETIC-LATCHING RF RELAY SERIES RF121 RELAY TYPE RF Magnetic-Latching, SPDT, Through-hole Relay DESCRIPTION The ultraminiature RF121 relay is built on Teledyne
More informationN type Coaxial Connectors
N type Coaxial Connectors N Series Features 1. 50 ohms wide varieties standard connectors 2. Screw on locking 3. High durability 4. Applicable standard: MI-C-39012/MI STD 348-304 Products guide s Straight
More informationAnalog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK Typical Applications The HMC547LP3
More informationHow To Design An Ism Band Antenna For 915Mhz/2.4Ghz Ism Bands On A Pbbb (Bcm) Board
APPLICATION NOTE Features AT09567: ISM Band PCB Antenna Reference Design Atmel Wireless Compact PCB antennas for 915MHz and 2.4GHz ISM bands Easy to integrate Altium design files and gerber files Return
More informationA SURVEY AND TUTORIAL OF DIELECTRIC MATERIALS USED IN THE MANUFACTURE OF PRINTED CIRCUIT BOARDS.
A SURVEY AND TUTORIAL OF DIELECTRIC MATERIALS USED IN THE MANUFACTURE OF PRINTED CIRCUIT BOARDS. By Lee W. Ritchey, Speeding Edge, for publication in November 1999 issue of Circuitree magazine. Copyright
More informationMMIC packaging. 1. Introduction 2. Data interface. Data submittal methods. Data formats. Single chip & MCM solutions. Contents
MMIC packaging MMIC packaging Contents 1. Introduction Page 2 2. Data Interface Page 2 3. Microwave package design requirement Page 3 4. Materials Page 3 5. Package layout design guidelines Page 4 6. Package
More informationAgilent E5063A ENA Series Network Analyzer. 100 khz to 4.5/ 8.5/18 GHz
Agilent E5063A ENA Series Network Analyzer 100 khz to 4.5/ 8.5/18 GHz The Best Balance Between Price and Performance The E5063A is a low cost network analyzer for simple passive component testing up to
More informationDynamic & Proto Circuits Inc. Corporate Presentation
Dynamic & Proto Circuits Inc. Corporate Presentation 1 DAPC Facility 54,000 Sq.ft./6,000 Sq.M 2 Multilayer Process 3 Solder Mask Options BLUE BLACK RED GREEN DRY FILM CLEAR 4 Investing in Technology New
More informationProCurve External Access Point Antennas
Certified for use with ProCurve Wireless Access Point 420, the ProCurve family of access point antennas is specifically designed to meet the needs of today's most demanding wireless LAN deployments. ProCurve
More informationspinner Measurement & Calibration equipment for network analyzers
spinner Measurement & Calibration equipment for network analyzers Edition B 2011 High Frequency Performance Worldwide www.spinner-group.com SPINNER test & calibration equipment for best measurement results
More informationATC 600S Series Ultra-Low ESR, High Q, NPO RF & Microwave Capacitors
AC 600S Series Ultra-Low ESR, High Q, NPO RF & Microwave Capacitors Features: Lowest ESR in Class Highest Working Voltage in class 250V Standard EIA Size: 0603 Laser Marking (Optional) RoHS Compliant High
More informationFlexible PCB Antenna with Cable Integration Application Note Version 2
Flexible PCB Antenna with Cable Integration Application Note Version 2 CONTENTS 1. BASICS 2. APPLICATIONS 3. SIZE 4. SHAPE 5. GROUND PLANE SIZE 6. IMPEDANCE 7. BANDWIDTH 8. VSWR 9. GAIN 10. EFFICIENCY
More informationManaging Connector and Cable Assembly Performance for USB SuperSpeed
Whitepaper Managing Connector and Cable Assembly Performance for USB SuperSpeed Revision 1.0 February 1, 2013 Abstract USB 3.0 connector and cable assembly performance can have a significant impact on
More informationHIGH REPEATABILITY, BROADBAND TO-5 RELAYS DPDT
HIGH REPEATABILITY, BROADBAND TO-5 RELAYS DPDT SERIES RF00 RF00D RF00DD RF0 RF0D RF0DD RELAY TYPE Repeatable, RF relay Repeatable, RF relay with internal diode for coil transient suppression Repeatable,
More informationSwitch Selection Guide
Switch Selection Guide FREQUENCY RANGE (GHz) 0.1 0.2 0.5 1 2 4 8 12.4 18 40 0.1 18 SWITCHES WITH INTEGRATED DRIVERS MODEL OR SERIES PAGE REFLECTIVE SPST SWITCHES* DM86, FM86 DM86H, FM86H 1 18 F91 0.2 4
More informationAuthor(s) Affiliation. Author(s) repeat Author and Affiliation boxes as needed. Affiliation. Publication Information
Author(s) First Name Middle Name Surname Role Email SMPTE Member? Owen Robert Barthelmes Director of Engineering Affiliation obarthelme s@amphen olrf.com Y Organization Address Country Amphenol RF 4 Old
More informationSunridge MCB Series Miniature Coaxial Interconnect, 2.5mm or 2.0mm Mated Height
Sunridge MCB series coaxial product fulfills the rigorous requirements of high frequency data transmission in digital world. Constructed in supreme Teflon coax cable and advanced mechanical design, MCB
More informationAgilent Electronic Calibration (ECal) Modules for Vector Network Analyzers
Agilent Electronic Calibration (ECal) Modules for Vector Network Analyzers N4690 Series, 2-port Microwave ECal 85090 Series, 2-port RF ECal N4430 Series, 4-port ECal Technical Overview Control ECal directly
More information10/100BASE-T Copper Transceiver Small Form Pluggable (SFP), 3.3V 100 Mbps Fast Ethernet. Features. Application
Features Compliant with IEEE 802.3u standard Link distance at 100Mbps: up to 100m per IEEE802.3 EEPROM with serial ID functionality Detailed product information in EEPROM Industry standard small form pluggable
More informationTS5010 TeraTune Programmable Bandpass Filter
FEATURES 0MHz to 90MHz Tunability 240 Frequency Steps Constant Q, Two-pole Butterworth Bandpass 1W Power Handling 0µs Tuning Speed Serial/Parallel Modes -40C to +85C DESCRIPTION The TS5010 series of TeraTune
More information0.2 mm Pitch, 0.9 mm above the board, Flexible Printed Circuit ZIF Connectors
0.9 0.2 mm Pitch, 0.9 mm above the board, Flexible Printed Circuit ZIF Connectors FH43B Series Space saving 17.8mm(81 pos. shown) 2.77 Can be mounted over conductive traces. Features 1. Low-profile, small
More informationiva Cable & Antenna Analyzer
iva Cable & Antenna Analyzer VSWR, Return Loss Measurement & Distance to Fault The iva Series Cable & Antenna Analyzer is an exciting new product from Kaelus that enables users to accurately measure VSWR/return
More informationMULTI-FLEX CIRCUITS AUSTRALIA. International Suppliers of PRINTED CIRCUIT BOARDS
MULTI-FLEX CIRCUITS AUSTRALIA International Suppliers of PRINTED CIRCUIT BOARDS AUSTRALIA Multi-Flex Circuits Australia Leading suppliers of HIGH QUALITY PRINTED CIRCUIT BOARDS for every purpose OUR COMMITMENT
More informationValu Builds for Rigid Flex
s for Rigid Flex Stable, robust builds for cost effective rigid flex We have gathered a set of low cost standard materials, with yield friendly design guidelines, to produce a cost effective rigid flex
More informationPCB Board Design. PCB boards. What is a PCB board
PCB Board Design Babak Kia Adjunct Professor Boston University College of Engineering Email: bkia -at- bu.edu ENG SC757 - Advanced Microprocessor Design PCB boards What is a PCB board Printed Circuit Boards
More informationAvaya WLAN 9100 External Antennas for use with the WAO-9122 Access Point
Avaya WLAN 9100 External Antennas for use with the WAO-9122 Access Point Overview To optimize the overall performance of a WLAN in an outdoor deployment it is important to understand how to maximize coverage
More informationMeasurement & Modeling Device Characterization Solutions
Also Available from Maury Microwave Measurement & Modeling Device Characterization Solutions Featuring The Most Complete Selection of Load Pull Solutions in the Test & Measurement Industry Helping Your
More informationMASW-000823-12770T. HMIC TM PIN Diode SP2T 13 Watt Switch for TD-SCDMA Applications. Features. Functional Diagram (TOP VIEW)
Features Exceptional Loss = 0.35 db Avg @ 2025 MHz, 20mA Exceptional Loss = 0.50 db Avg @ 2025 MHz, 20mA Higher - Isolation = 31dB Avg @ 2025 MHz, 20mA Higher RF C.W. Input Power =13 W C.W.(-Ant Port)
More informationWAVEGUIDE COMPONENT Specifications and Design Handbook. Edition #7
WAVEGUIDE COMPONENT Specifications and Design Handbook Edition #7 CONTINENTAL MICROWAVE DIVISION Integrated Waveguide Assemblies Waveguide components are just the beginning. Continental Microwave Division
More informationPCB connectors SMD and also pin-in-paste types - are available as limited detent or smooth bore types.
coaxial connectors from Rosenberger combine the advantages of SMP connectors minimum board-to-board spaces and of SMA connectors high performance and high power rating. Minimum board-to-board distances
More informationPC/104, PC/104 -Plus, VarPol connectors
164 PC/104, PC/104 -Plus, VarPol connectors Definitions 166 Technical specifications 168 Hole specifications 169 PC/104 170 PC/104-Plus 172 Accessories: PC/104 and PC/104-Plus 174 VarPol angled pin header
More informationiva Cable & Antenna Analyzer
iva Cable & Antenna Analyzer VSWR, Return Loss Measurement & Distance to Fault The iva Series Cable & Antenna Analyzer is an exciting new product from Kaelus that enables users to accurately measure VSWR/return
More informationSymbol Parameters Units Frequency Min. Typ. Max. 850 MHz 14.8 16.3 17.8
Product Description Sirenza Microdevices SGC-689Z is a high performance SiGe HBT MMIC amplifier utilizing a Darlington configuration with a patented active-bias network. The active bias network provides
More informationPHASE SHIFT DUPLEXERS
-PORT WAVEGUIDE DIFFERENTIAL PHASE SHIFT CIRCULATORS (DUPLEXERS) AVERAGE POWER KW 00 0 DIFFERENTIAL PHASE SHIFT DUPLEXERS WAVEGUIDE TECHNOLOGY COAXIAL TECHNOLOGY 0. 0 00 FREQUENCY GHz General description
More informationOperating Temperature Range: -30 to +85ç (Note 1) Operating Humidity Range: 40 to 80%
All non- products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website search at www.hirose-connectors.com, or contact your Hirose sales representative.
More informationS-PARAMETER MEASUREMENTS OF MEMS SWITCHES
Radant MEMS employs adaptations of the JMicroTechnology test fixture depicted in Figure 1 to measure MEMS switch s-parameters. RF probeable JMicroTechnology microstrip-to-coplanar waveguide adapter substrates
More information1000 Series Miniature Slide Switches
Miniature Switches Features/Benefits Variety of actuators and terminations Panel mount tabs available Epoxy terminal seal compatible with bottom-wash cleaning RoHS compliant Typical Applications Test &
More informationINTELLIGENT INTERACTIVE SYNTHESIZER SURFACE MOUNT MODEL: MFSH615712-100
SURFACE MOUNT MODEL: MFSH6572 65-72 MHz FEATURES: Small Size, Surface Mount (.6" x.6") Low Phase Noise Standard Programming Interface Ultra Wide Tuning Range Lead Free - RoHS Compliant Patented REL-PRO
More informationSTRAFT-P98L15. Antenna tuner for cellular application. Features. Description. Applications. Benefits
Antenna tuner for cellular application Datasheet production data Features 50 nominal Input for a wide range of output impedances Wide operating frequency range (824 MHz to 2170 MHz) Specifically optimized
More informationOMNIYIG. .5 TO 2 GHz, 1 TO 4 GHz, 6 to 18 GHz Thin Film YIG-TUNED OSCILLATORS OUTLINE DIMESIONS MOUNTING SURFACE GND +15V + TUNE - HTR HTR
. TO Hz, 1 TO Hz, to 1 Hz Thin Film YITUNED OSCILLATORS Highly Reliable StateoftheArt ThinFilm Technology s. to 1 Hz oscillators employ thinfilm technology, coupled with aas FET transistors, and were designed
More informationAgilent X/P/K281C Adapters
Agilent X/P/K281C Adapters Including Options 006, 012, 013, 106 Operating and Service Manual Contents 1 Introduction 7 Product Overview 8 Options 8 Instruments Covered by Manual 10 2 Installation 11 Initial
More information2.0 Responsibilities. 2.1 Management is responsible for assigning all aspects of sample records and documents.
1.0 Purpose 1.1 This procedure describes the process for controlling and recording samples of our products provided to customers prior to their orders for their testing and evaluation. Procedure includes
More informationRF Connector Solutions
RF Connector Solutions C o n n e c t i n g I n n o v a t i o n t o A p p l i c a t i o n Winchester Electronics was established in 1941 and is today a global leader in the design, development, and deployment
More informationConnectors according to IEC 61076-4-101
Definitions Connectors according to IEC 61076-4-101 The hardmetric connector system ept hm 2.0 was developed and manufactured according to the international standard IEC 61076-4-101. Thus the user can
More informationCo-simulation of Microwave Networks. Sanghoon Shin, Ph.D. RS Microwave
Co-simulation of Microwave Networks Sanghoon Shin, Ph.D. RS Microwave Outline Brief review of EM solvers 2D and 3D EM simulators Technical Tips for EM solvers Co-simulated Examples of RF filters and Diplexer
More informationVDI Mixer/Amplifier/Multiplier Chains (MixAMCs)
VDI Mixer/Amplifier/Multiplier Chains (MixAMCs) VDI s MixAMCs provide high performance broadband downconversion and frequency extension of microwave spectrum analyzers into the THz range. Models are currently
More informationRF and Microwave Accessories. CD-ROM Catalog. Find the right component for your Rohde & Schwarz test & measurement equipment
RF and Microwave Accessories CD-ROM Catalog Find the right component for your Rohde & Schwarz test & measurement equipment Product group Typical applications Adapters Interchanging of various connector
More informationApplication Guide to RF Coaxial Connectors and Cables
Application Guide to RF Coaxial Connectors and Cables By: Michael J. Hannon Product Applications Engineer and Pat Malloy, Sr. Applications Engineer There is a wide variety of coaxial connectors and cables
More information