LINEAR SLIDE CYLINDER LCG SERIES

Transcription

1 Highly accurate, rigid LINEAR SLIDE CYLINDER LCG SERIES LINEAR SLIDE CYLINDER LCG SERIES CC-852A

2 Highly accurate, LCG Series linear slide cylinder. ( 6, 8, 2, 6, 20, or 25) The air cylinder s wide guide improves accuracy and rigidity. The linear guide table acts as the sliding table to provide outstanding accuracy, rigidity, and easy of use. rigid, and easy to use Installation holes on two surfaces Wide linear guide Increased design freedom Design is easily made since symmetrical stoppers, multiside piping, and two-surface installation and positioning holes are provided. Change to symmetrical Ample option variations Standard, position locking, and clean specification models are available. Varied options include a stopper for adjustable stroke and a stopper with a shock absorber. * The shock absorber stopper cannot be used for clean model specifications. Sliding table Change to symmetrical Arrows ( ) show the piping direction. Standard port for back piping provided for all bore sizes Improved accuracy The linear guide's table is used for the sliding table. Accuracy is improved over conventional products. Parallelism 0.03 mm ( 2-30 mm stroke) End plate perpendicularity 0.05 mm Easier to use The cylinder and linear slide are now designed together, reducing design work hours. Design for symmetrical stopper installation and multiside piping improve the degree of freedom and ease of use. Linear slide cylinder Cylinder switch installation groove Higher rigidity 0.05 (mm) Displacement 0 Applications Radial moment Storage of small parts in tray or removal of parts from tray 5 30 Load moment (N m) Feeding of small parts Symmetric stopper The slide table material has been changed from conventional aluminum to stainless steel or steel. Rigidity is further increased by using this slide table together with the wide guide. ( 2-30 mm stroke) LCS (Conventional CKD product) LCG LCG Series products Double acting single rod LCG Linear guide with four guide ball rows (excluding 6 and 8) Four rows of guide balls ensure stable operation in any load direction. The guide ball contact is narrower than the two-row layout guide, so the frictional resistance generated during rotation is low. This enables smooth operation with increased accuracy and rigidity. Double acting position locking LCG-Q Double acting single rod (clean room specifications) LCG-P7 4-row layout, 2-point contact Guide ball Rotary shaft center Rotary shaft center Contact width (2-point) Model variation 2-row layout, 4-point contact Rotary shaft center Guide ball Contact width (4-point) Bore size Stopper for adjustable stroke Single side adjustment range 0 to 5 mm 2-color switch selectable The proximity 2-color display switch is selectable. Switches are flush with the panel for a neat appearance. RoHS Directive-compliant Environmentally harmful substances, including lead and hexavalent chrome, have been eliminated. Stroke length (mm) Stock absorber stopper Shock cushioned at stroke end * Custom order rustproof products are available. Refer to page 54 for details.

3 Series variation Linear slide cylinder LCG Series LCG Series Series variation : Standard : Option : Available : Not available Option Stopper for adjustable stroke Shock absorber type stopper Variation Model no. JIS symbol Bore size (mm) Stroke length (mm) Stopper position Stopper position 2 Stopper position 3 Stopper position 4 Stopper position and 3 Stopper position 2 and 4 Stopper position Stopper position 2 Stopper position 3 Stopper position 4 Stopper position and 3 Stopper position 2 and 4 Switch Page S S2 S3 S4 S5 S6 A A2 A3 A4 A5 A6 ø6 Double acting single rod type LCG ø8 ø2 ø6 ø20, ø25 Double acting position locking type LCG-Q ø8 ø2 ø6 23 ø20, ø25 ø6 Double acting single rod type Clean room specifications LCG-P7* ø8 ø2 ø6 3 ø20, ø25 Intro Intro 2

4 Safety precautions Always read this section before starting use. When designing and manufacturing a device using CKD products, the manufacturer is obligated to check that device safety mechanical mechanism, pneumatic control circuit, or water control circuit and the system operated by electrical control that controls the devices is secured. It is important to select, use, handle, and maintain the product appropriately to ensure that the CKD product is used safely. Observe warnings and precautions to ensure device safety. Check that device safety is ensured, and manufacture a safe device. WARNING This product is designed and manufactured as a general industrial machine part. It must be handled by an operator having sufficient knowledge and experience in handling. 2 Use this product in accordance of specifications. This product must be used within its stated specifications. It must not be modified or machined. This product is intended for use as a general-purpose industrial device or part. It is not intended for use outdoors or for use under the following conditions or environment. Note that this product can be used when CKD is consulted prior to use and the customer consents to CKD product specifications. The customer must provide safety measures to avoid risks in the event of problems. Use for special applications requiring safety including nuclear energy, railroad, aviation, ship, vehicle, medical equipment, equipment, or applications coming into contact with beverage or food, amusement equipment, emergency shutoff circuits, press machine, brake circuits, or for safeguard. 2 Use for applications where life or assets could be adversely affected, and special safety measures are required. 3 Observe corporate standards and regulations, etc., related to the safety of device design and control, etc. ISO 444, JIS B 8370 (pneumatic system rules) JFPS 2008 (principles for pneumatic cylinder selection and use) Including High Pressure Gas Maintenance Law, Occupational Safety and Sanitation Laws, other safety rules, body standards and regulations, etc. 4 Do not handle, pipe, or remove devices before confirming safety. Inspect and service the machine and devices after confirming safety of the entire system related to this product. 2 Note that there may be hot or charged sections even after operation is stopped. 3 When inspecting or servicing the device, turn off the energy source (air supply or water supply), and turn off power to the facility. Discharge any compressed air from the system, and pay enough attention to possible water leakage and leakage of electricity. 4 When starting or restarting a machine or device that incorporates pneumatic components, make sure that the system safety, such as pop-out prevention measures, is secured. 5 Observe warnings and cautions on the pages below to prevent accidents. The safety cautions are ranked as DANGER, WARNING and CAUTION in this section. DANGER: When a dangerous situation may occur if handling is mistaken leading to fatal or serious injuries, or when there is a high degree of emergency to a warning. WARNING: When a dangerous situation may occur if handling is mistaken leading to fatal or serious injuries. CAUTION: When a dangerous situation may occur if handling is mistaken leading to minor injuries or physical damage. Note that some items described as CAUTION may lead to serious results depending on the situation. In any case, important information that must be observed is explained. Intro 3 Disclaimer. CKD cannot be held liable for any business interruption, loss of profit, personal injury, delay cost, or any other ancillary or indirect loss, cost, or damage resulting from the use of or faults in the use of CKD products. 2. CKD cannot be held responsible for the following damage: Damage resulting from failure of CKD parts due to fire from reasons not attributable to CKD, or by intentional or negligence of a third party or customer. 2 When a CKD product is assembled into customer equipment, damage that could have been avoided if customer equipment were provided with functions and structure, etc., generally accepted in the industry. 3 Damage resulting from use exceeding the scope of specifications provided in CKD catalogs or instruction manuals, etc., or from actions not following precautions for installation, adjustment, or maintenance, etc. 4 Damage resulting from production modifications not approved by CKD, or from faults due to combination with other software or other connected devices.

5 Pneumatic components Safety precautions Always read this section before starting use. Refer to Pneumatic cylinders (CB-029SA) for the general details on cylinders and cylinder switch. Design & Selection. Common CAUTION Refer to the LCG Selection Guide on pages 47 to 50 when selecting the cylinder. When using the cylinder where it could be subject to water or oil exposure, where it could corrode, or where high levels of dust are present, the cylinder could be damaged or malfunction. Protect the product with a cover. Precautions for using type with switch When using the T*V switch with the cylinder with a stopper for adjustable stroke (S3**, S4**, S5**, S6**) or shock absorber stopper (A3**, A4**, A5**, A6**), the head side switch could interfere with the stopper. Install the switch on the side opposite the stopper. When using a switch with a stroke of less than 30, one switch is installed in each of the two grooves on the body. Check the direction of leads in design. A powerful magnet placed near this product could magnetize the table and cause the switch to malfunction. 2. Position locking type LCG-Q CAUTION Do not use a 3-position valve. Do not use this cylinder with a 3-position valve, especially with a closed center metal seal. The lock is not applied if pressure is sealed on the port having the lock. Even if the lock is applied, air leaking from the valve may enter the cylinder or the lock may be released over time. Installation & Adjustment. Common; Piping CAUTION When changing a piping port position, apply adhesive to M3 and M5 plug (hexagon socket head set screw). (Low intensity adhesive such as LOCTITE 222, 22, THREE BOND 344 recommended) Precautions for piping joint Install a flow control valve when piping. The applicable joints are shown as below. Descriptions Port Joint outer Bore size Port size dimension Applicable joints diameter B (mm) A SC3W-M3-4 ø6 M3 4 SC3WU-M3-4 SC3W-M3-3.2 SC3WU-M3-3.2 GWS3-M3-S GWS4-M3-S ø8 or less ø8 5.5 SC3W-M5-4 SC3W-M5-6 ø or less ø2 5.5 GWS4-M5-S GWS4-M5 SC3W-M5-4 M5 SC3W-M5-6 ø6 6.5 GWS4-M5-S ø3 GWS4-M5 or less GWL4-M5 GWL6-M5 GWS6-M5 SC3W-6-4, 6, 8 ø20 8 GWS4-6 Rc/8 ø25 9 GWS8-6 GWL6-6 GWS6-6 GWL4-6 ø5 or less A øb Intro 4

6 LCG Series Installation & Adjustment 2. Common; installation CAUTION Do not dent or scratch or otherwise compromise flatness of the installation or table surface. Maintain flatness of the corresponding installed component on the body or table at 0.02 mm or less. Observe the following values for the bolt insertion length and tightening torque when installing this product. <Fig. > A B Observe the following valves for bolts at the stopper and in nut tightening torque. <Fig. A> Stopper bolt Stopper block Stopper 2 Stopper bolt mounting nut 3 Stopper block mounting bolt Stopper mounting bolt Hexagon socket set screw stopper with rubber cushion Stopper block Stopper 3 Stopper block mounting bolt L Shock absorber 2 Shock absorber mounting nut Stopper mounting bolt Shock absorber A B Descriptions Applicable bolts Tightening torque (N m) Applicable bolts Tightening torque (N m) Max. screw depth L (mm) LCG-6 M3 x to. M4 x to LCG-8 M3 x to. M4 x to LCG-2 M4 x to 2.4 M5 x to 5. 8 LCG-6 M5 x to 5. M6 x to LCG-20 M5 x to 5. M6 x to LCG-25 M6 x to 8.6 M8 x to Observe the following bolt insertion lengths and tightening torque when installing the jig on the slide table or end plate. <Fig. 2> L L Model Stopper mounting bolt 2 Stopper bolt mounting nut 3 Stopper block mounting bolt 2 Shock absorber mounting nut (N m) (N m) (N m) LCG to to to 0.8 LCG to to to 0.8 LCG to to to 0.8 LCG to to to.8 LCG to to to.8 LCG to to to 3.5 Sources of magnetism such as steel plates near the cylinder switch could cause the cylinder to malfunction. Keep at least 0 mm from the cylinder. (Same for all bore size) 0mm and over Magnetic source such as steel plate Table Descriptions Applicable bolts Tightening torque (N m) Max. screw-in length L (mm) LCG-6 M3 x LCG-8 M3 x LCG-2 M4 x LCG-6 M5 x LCG-20 M5 x LCG-25 M6 x End plate Descriptions Applicable bolts Tightening torque (N m) Screw-in length L (mm) LCG-6 M3 x to 6 LCG-8 M3 x to 7 LCG-2 M4 x to 9 LCG-6 M5 x to 9 LCG-20 M5 x to LCG-25 M6 x to If cylinders are adjacent, the cylinder switch could malfunction. Check that the following distance is maintained between cylinder surfaces. (Same for all bore size) 20mm and over 20mm and over The CKD shock absorber is treated as a consumable. Replace the shock absorber if energy absorption performance drops or if movement is no longer smooth. Intro 5

7 LCG Series 3. Position locking type LCG-Q CAUTION The locking mechanism functions at the stroke end, so applying the stopper with the external stopper at mid-stroke prevents the locking mechanism from functioning and the load may drop. Before setting the load, check that the locking mechanism functions correctly. If piping on the side with the lock is thin and long, or if the speed controller is separated from the cylinder port, exhaust may slow, taking time for the lock to function. This may also occur if the silencer on the solenoid valve s EH. port is clogged. Supply a pressure higher than the minimum working pressure to the port having the locking mechanism. During Use & Maintenance. Common CAUTION Apply AFJ grease (THK) to guide rails once a month or every,000,000 operations, whichever is sooner. Check for table corrosion. The table is made of martensitic stainless steel 6 to 6 in diameter or alloy steel 20 or 25 in diameter. Use in a hot, humid environment or contact with water due to condensation, etc., could cause rust. 2. Position locking type LCG-Q WARNING If pressure is supplied to port (A) in the locked state with neither port pressurized, locks may not be releasable or may be released suddenly, causing the piston rod to pop out, which is extremely dangerous. When releasing the locking mechanism, supply pressure to port (B) and check that no load is applied to the locking mechanism. Port Port Side without locking mechanism A B W After manually operating the locking mechanism, return the locking mechanism to the original position. Do not use a manual override except during adjustment, because this may be dangerous. Release the lock when installing or adjusting the cylinder. The lock could be damaged if the cylinder is installed while the lock is applied. Do not use multiple cylinders synchronized. Do not move one workpiece using more than two position locking cylinders synchronized. One of the cylinder s locks may not be released. Use the flow control valve with meter-out control. Locks may not be released during meter-in control. Use the side with the lock with the cylinder stroke end. If the cylinder s piston does not reach the stroke end, the lock may not be applied or may not be released. How to release Screw a hexagon socket head cap screw (M3 20) into the stopper piston, and pull the bolt up 3 mm with a force of 20N and over. The stopper piston moves and the lock is released during horizontal no-load installation or with the rod port pressurized. When the hand is released, the stopper piston is returned by the internal spring and enters the piston rod slot, locking the cylinder. If slower speed is to be increased with the quick exhaust valve, the cylinder may move out faster than the lock pin and prevent the lock pin from being released correctly. Do not use a quick exhaust valve with the position locking cylinder. CAUTION If negative pressure is applied to the locking mechanism, the lock may be released. Use a discrete solenoid valve or use an individual exhaust manifold. Hexagon socket head cap screw M3 x 20 Coil spring Stopper piston Piston rod slot 3 When unlocked When locked Intro 6

8 Linear slide cylinder double acting single rod type LCG Series Bore size: ø6, ø8, ø2, ø6, ø20, ø25 JIS symbol Specifications Descriptions LCG Bore size mm ø6 ø8 ø2 ø6 ø20 ø25 Actuation Working fluid Double acting Compressed air Max. working pressure MPa 0.7 Min. working pressure MPa 0.5 (Note ) Withstanding pressure MPa Ambient temperature -0 to 60 (to be unfrozen) (Note 2) Port size Body side surface M3 M5 Rc/8 Rear body M3 M5 Rc/8 Stroke tolerance mm (Note 3) 0 Working piston speed mm/s 50 to 500 (Note 4) Cushion Rubber cushioned Lubrication Not required (when lubricating, use turbine oil Class one ISOVG 32.) Allowable energy absorption J Refer to the table 3 on Page 47. Note : 0.2 MPa when using the shock absorber stopper 6 in diameter. Note 2: The maximum temperature is 50 when the switch 6 in diameter is used when installing on a steel plate. Note 3: When not using a stopper, a slight gap may exist between the end plate and floating bushing. Note 4: Use the stopper for adjusting the stroke between 50 and 200 mm/s. Stroke length Bore size (mm) Standard stroke length (mm) ø6 0, 20, 30, 40, 50 ø8 0, 20, 30, 40, 50, 75 ø2 0, 20, 30, 40, 50, 75, 00 ø6 0, 20, 30, 40, 50, 75, 00, 25 ø20 0, 20, 30, 40, 50, 75, 00, 25, 50 ø25 0, 20, 30, 40, 50, 75, 00, 25, 50 Note: Stroke length other than above is not available.

9 Switch specifications /2 color indicator Descriptions Applications Proximity 2 wire Proximity 3 wire Proximity 2 wire Proximity 3 wire T2H/T2V T2WH/T2WV T3H/T3V T3WH/T3WV F2H/F2V F2YH/F2YV F3H/F3V F3YH/F3YV Programmable Controller dedicated Programmable Controller and relay Programmable Controller dedicated Programmable Controller and relay Output type - NPN output - NPN output Power voltage - 0 to 28V DC - 0 to 28V DC Load voltage 0 to 30V DC 24V DC 0% 30V DC or less 0 to 30V DC 24V DC 0% 30V DC or less Load current 5 to 20mA 00mA or less 50mA or less 5 to 20mA 00mA or less 50mA or less Light LED (ON lighting) Red/green LED (ON lighting) LED (ON lighting) Red/green LED (ON lighting) LED (ON lighting) Red/green LED (ON lighting) LCG Series Specifications LED (ON lighting) Leakage current ma or less 0 A or less ma or less 0 A or less Descriptions Applications T0H/T0V Programmable Controller and relay Reed 2 wire T5H/T5V Programmable controller, relay IC circuit (without light), serial connection Load voltage 2/24VDC 0VAC 5/2/24VDC 0VAC Load current 5 to 50mA 7 to 20mA 50mA or less 20mA or less Light Leakage current LED (ON lighting) 0mA Without indicator light Red/green LED (ON lighting) Cylinder weight Basic type (Unit: g) Bore size Basic stroke type (mm) (mm) ø ø ø ø ,220,40,620 - ø20,260,260,260,380,500,920 2,20 2,50 2,800 ø25 2,070 2,070 2,070 2,230 2,430 3,240 3,660 4,080 4,530 Additional variations and options (stoppers) (Unit: g) Bore size Option and stopper symbol (mm) S to S4 S5, S6 A to A4 A5, A6 ø ø ø ø ø ø

10 LCG Series 3 How to order Without switch LCG With switch Model no. 8 A Bore size 40 B Stroke length Note on model no. selection Note : Use stopper parts for the adjustable stroke on page 6 when changing the adjustable stroke range. Note 2: When using a shock absorber, refer to the stopper dimensions table on page 2 for the adjustable stroke range. Note 3: Refer to stopper dimensions on page 2 for port locations. Note 4: If no stopper is provided, the standard port locations are () and (3) below. Note 5: The stopper for adjustable stroke and shock absorber stopper combination is available as a customized part. Note 6: Selectable only when using a stopper. Note 7: Refer to the selection table on page 4 for option combinations. Note 8: A**, A2**, A5**, and A6** at ø6 to ø8-0st or ø2 to ø25-20st or less cannot be adjusted with the standard stopper, and are available only as customized parts. Note 9: When installing two switches with ø6-0st S*** or A***, select the F*H switch. <Example of model number> LCG-2-40-F2H-R-ADT Model: Linear slide cylinder double acting single rod type LCG A Bore size : ø2 B Stroke length : 40mm C Switch model no. : Proximity and 2 wire Axial lead wire D Switch quantity : With one on rod end E Other options : shock absorber type Stopper position With side or base port Material, alloy steel (nitriding) S5 LCG 2 40 F2H* R ADT D Switch quantity C Switch model no. E Option Stopper position Symbol A Bore size 6 ø6 8 ø8 2 ø2 6 ø6 20 ø20 25 ø25 B Stroke length (mm) C Switch model no. Axial Radial lead wire lead wire Descriptions Contact Indicator Lead wire F2H* F2V* 2-wire One color indicator F3H* F3V* 3-wire Proximity F2YH* F2YV* 2 color indicator 2-wire F3YH* F3YV* 3-wire T0H* T5H* T0V* T5V* Reed One color indicator 2-wire T2H* T2V* 2-wire One color indicator T3H* T3V* 3-wire T2WH* T2WV* T3WH* T3WV* *Lead wire length Blank Proximity m (standard) 3 3m (option) 5 5m (option) D Switch quantity R H D One on rod end One on head end Two E Option Blank No option 2 color indicator 2-wire 3-wire S Stopper for adjustable stroke Bore size (ø) Bore size ø6 ø8 ø2 ø6 ø20 ø25 Adjustable stroke single side 5mm Note, Note 5, Note 7 S** Stopper position (Changeable to 4 ) S2** Stopper position 2 (Changeable to 3 ) S3** Stopper position 3 (Changeable to 2 ) S4** Stopper position 4 (Changeable to ) S5** Stopper position and 3 S6** Stopper position 2 and 4 Stopper installation position A Shock absorber type stopper Note 2, Note 5, Note 7 A** Stopper position (Changeable to 4 ) A2** Stopper position 2 (Changeable to 3 ) A3** Stopper position 3 (Changeable to 2 ) A4** Stopper position 4 (Changeable to ) A5** Stopper position and 3 A6** Stopper position 2 and 4 ** section Blank Port at stopper section: no port Stopper installation position D Port at stopper section: with side or base port Note 3, Note 6 Blank Stopper block material: Rolled steel T Stopper block material: Alloy steel (nitriding) Note 6

11 LCG Double acting, single rod selection table (Combination with stopper for adjustable stroke and shock absorber stopper) Model no. symbol LCG LCG Series How to order : Available -: Not available Option symbol Stopper for adjustable stroke Shock absorber type stopper Bore size Stroke length S S2 S3 S4 S5 S6 A A2 A3 A4 A5 A6 ø6, ø8 ø2 to ø and over 0 to and over Option symbol D: with stopper section port and T: stopper block alloy steel (nitriding) combined as shown in the selection table above. 4

12 LCG Series How to order switch If ø6 to ø2 If ø6 to ø25 SW F2H SW T2H3 Switch model no. (Page 3 item C ) Switch model no. (Page 3 item C ) How to order stopper set Stopper section and stopper for adjustable stroke or shock absorber stopper set Use when changing from standard to stopper for adjustable stroke or with shock absorber stopper LCG 2 S 2 D Bore size (Page 3 item A ) A B Stopper type S Stopper for adjustable stroke A Shock absorber type stopper Stopper installation position For stopper position or 4 2 For stopper position 2 or 3 C Port at stopper section Blank No port D With side and bottom ports Precautions for ordering stopper set S0 is included in the stopper for adjustable stroke parts for the stopper for adjustable stroke set. When installing at position or 2 (refer to page 3), add parts shown on the right based on the stoke or adjustable stroke length. Model no. symbol LCG Series -: not available Option symbol Discrete stopper for adjustable stroke Adjustable stroke length (mm) Bore size Stroke length ø6, ø8 0 S and over Addition not required S02-0 S ø2 to ø25 20 S02 S03-30 and over Addition not required S02 S03 5

13 LCG Series How to order How to order the discrete stopper for adjustable stroke Hexagon socket head set screw with urethane Use for changing the adjustable stroke range or setting to the middle stroke LCG 2 S02 Precautions for ordering discrete stopper Only when installing the discrete stopper for an adjustable stroke or discrete shock absorber stopper at installation position or 2 (refer to page 3), the combination will be as shown on the right depending on the stroke or adjustable stroke length. Bore size (Page 3 item A ) Model no. symbol LCG Series -S, S2, S5, S6 -A, A2, A5, A6 A Adjustable stroke range S0 S02 S03 Single 5mm (standard) Single 5mm Single 25mm -: combination not available Discrete stopper for adjustable stroke Option symbol Discrete shock Adjustable stroke length (mm) absorber type stopper Bore size Stroke length S ø6, ø8 20 and over S0 S02 - A0 ø2 to ø25 Designate S0, S02, or S03 for A. Note: S03 is not used for ø6 or ø8. Depending on the type, the incompatible models or adjustable stroke ranges may differ from the above values. 0 S S02 S and over S0 S02 S03 A0 How to order the discrete shock absorber stopper Sets of shock absorber and stopper cap Use for changing from the stopper for an adjustable stroke to the shock absorber stopper. LCG 2 A0 Shock absorber Stopper cap Bore size (Page 3 item A ) Note: Some models may not be available depending on the type. Refer to Page 3. Refer to Page 2 for adjustable stroke range of a shock absorber type stopper. Applicable shock absorber model No. Model Shock absorber model no. LCG-6 NCK LCG-8 NCK LCG-2 NCK LCG-6 NCK LCG-20 NCK LCG-25 NCK Discrete stopper block model no. display Use when changing from standard to stopper for adjustable stroke or with shock absorber stopper LCG 2 SB T Bore size (Page 3 item A ) A Stopper block SB ø6, ø8: 30 mm stroke or less ø2 to ø25: 50 mm stroke or less SB2 ø6, ø8: 40 mm stroke and over ø2 to ø25: 75 mm stroke and over B Material Blank T Stopper block material: Rolled steel Stopper block material: Alloy steel (nitriding) 6

14 LCG Series Internal structure and parts list LCG A B C A section for ø6 A section for ø8 B section for ø6, ø8, ø2 C section for ø Parts list No. Parts name Material Remarks No. Parts name Material Remarks Hexagon socket head cap screw Alloy steel Zinc chromate 7 Cushion rubber (H) Urethane rubber 2 Floating bush A Alloy steel Zinc chromate 8 Guard gasket Nitrile rubber 3 Floating bush B Stainless steel ø8: steel 9 C type snap ring Only ø8 to 25 ø8: Steel ø2 to 25: Stainless steel 4 C type snap ring Only ø8 to 25 ø2 to 25: Stainless steel 20 Guard Aluminum alloy Chromate 5 Rod packing seal Nitrile rubber 2 End plate Aluminum alloy Alumite 6 Metal gasket Nitrile rubber 22 Hexagon socket head cap screw Alloy steel Zinc chromate 7 Rod bushing Aluminum alloy Alumite 23 Plug Stainless steel 8 Piston rod Stainless steel ø6 to 6: Stainless steel 24 Table 9 Cylinder body Aluminum alloy Hard alumite ø20, 25: Steel 0 Cushion rubber (R) Urethane rubber 25 Hexagon socket head set screw Stainless steel ø6: Only 0, 40, 50st 26 Floating bush A Stainless steel Spacer Aluminum alloy ø8: Only 0st 27 Floating bush B Stainless steel ø2, 6, 20, 25: Only 0, 20st 28 Hexagon socket head set screw Stainless steel Only ø6 2 Magnet spacer Aluminum alloy Chromate 29 Rod bushing A Stainless steel 3 Magnet Plastic 30 Cap Aluminum alloy Chromate 4 Piston Aluminum alloy Chromate 3 Piston A Aluminum alloy Chromate 5 Plug Stainless steel 32 Piston B Aluminum alloy Chromate 6 Piston packing seal Nitrile rubber Repair parts list Bore size (mm) Kit No. Repair parts number ø6 LCG-6K ø8 LCG-8K ø2 LCG-2K ø6 LCG-6K ø20 LCG-20K ø25 LCG-25K 7

15 Internal structure and parts list Configuration with stopper Type with stopper section port on side or base (Symbol D) LCG Series Internal structure and parts list Type without stopper section port Parts list No. Parts name Material Remarks No. Parts name Material Remarks Stopper bolt Alloy steel Nickeling Stopper block 2 Hexagon nut Alloy steel Nickeling (stopper block symbol: blank) Steel 7 3 Stopper A Aluminum alloy Alumite Stopper block Alloy steel 4 Gasket Urethane rubber (stopper block symbol: T) Nitriding Nickeling 5 Hexagon socket head cap screw Alloy steel Zinc chromate 8 Stopper B Aluminum alloy Alumite 6 Hexagon socket head cap screw Alloy steel Zinc chromate 9 Stopper bolt Alloy steel Nickeling 0 Cushion rubber Urethane rubber 8

16 LCG Series Dimensions (bore size: ø6) LCG-6 Stroke length: 0, 20, 30 (Main fixing holes in this drawing are for the 20 mm stroke.) RD 2-M3 depth 3 Piping port 2-main body fixing hole (Refer to A-A' cross section.) depth W A M3 depth 4 Common port (plug) M3 depth D A' 20 L2 L 3 x 2-M3 depth depth 3 2-M2.6 depth 3.5 V M2.6 depth M3 depth 3 Piping port (plug) 2-R.5 D, E oval hole section dimensions HD 0.5 ø6 ø3.4 M4 depth depth 3 20 E 2 A-A' cross section 5 Y depth 3 Dimensions table per stroke length Stroke length L L V W Y RD HD

17 Dimensions (bore size: ø6) LCG Series Dimensions LCG-6 Stroke length: 40, 50 (Main fixing holes in this drawing are for the 50 mm stroke.) depth 3 n-main body fixing hole (Refer to A-A' cross section.) W D P=20 P x (n-) L2 L 4 x 2-M3 depth 3 V M2.6 depth M3 depth 3 Piping port (plug) HD depth 3 P=20 P x (n-) E 5 Y depth 3 Dimensions table per stroke length Stroke length L L n 3 4 V W Y RD 25.5 HD

18 LCG Series Dimensions (bore size: ø8) LCG-8 Stroke length: 0, 20, 30 (Main fixing holes in this drawing are for the 30 mm stroke.) RD 2-M5 depth 4 Piping port depth W A 2-main body fixing hole (Refer to A-A' cross section.) M3 depth 4 Common port (plug) M3 depth D 7 A' L2 L 3 x 2-M3 depth depth 3 2-M2.6 depth 3.5 V M5 depth 4 Piping port (plug) 2-R.5 D, E oval hole section dimensions HD 5.5 ø6.8 ø3.4 M4 depth depth E 3 A-A' cross section depth 3 Dimensions table per stroke length Stroke length L L V W 6 26 RD 24 4 HD 23

19 Dimensions (bore size: ø8) LCG Series Dimensions LCG-8 Stroke length: 40, 50, 75 (Main fixing holes in this drawing are for the 50 mm stroke.) depth 3 n-main body fixing hole (Refer to A-A' cross section.) W D 7 30 P=20 P x (n-) 9 L2 L 4 x 2-M3 depth 3 V M3 depth 3 2-M5 depth 4 Piping port (plug) HD 5.5 P x (n-) P=20 E depth 3 6 Y depth 3 Dimensions table per stroke length Stroke length L L n V W Y RD 4 HD 32 2

20 LCG Series Dimensions (bore size: ø2) LCG-2 Stroke length: 0, 20, 30, 40, 50 (Main fixing holes in this drawing are for the 30 mm stroke.) RD 2-M5 depth 4 Piping port depth W A n-main body fixing hole (Refer to A-A' cross section.) 2-M3 depth 5 Common port (plug) D A' P=30 P x (n-) L2 L 3 x 2-M4 depth 4 2-M3 depth 3.5 V M3 depth 5 2-M5 depth 4 Piping port (plug) M4 depth depth 4 2-R.5 D, E oval hole section dimensions HD ø9 ø4.5 M5 depth depth 4 P x (n-) P=30 E 6 A-A' cross section 8 Y depth 4 Dimensions table per stroke length Stroke length L 9 0 L n 2 3 V W Y RD HD 27 3

21 Dimensions (bore size: ø2) LCG Series Dimensions LCG-2 Stroke length: 75, 00 (Main fixing holes in this drawing are for the 00 mm stroke.) depth 4 4-main body fixing hole (Refer to A-A' cross section.) W D L2 L 4 x 2-M4 depth 4 V M3 depth 5 2-M5 depth 4 Piping port (plug) 3 3 HD depth E 8 Y depth 4 Dimensions table per stroke length Stroke length L L V 6 4 W Y RD 2.5 HD 36 4

22 LCG Series Dimensions (bore size: ø6) LCG-6 Stroke length: 0, 20, 30, 40, 50 (Main fixing holes in this drawing are for the 30 mm stroke.) RD 2-M5 depth 4 Piping port W A n-main body fixing hole (Refer to A-A' cross section.) 2-M3 depth 4 Common port (plug) D 9 43 A' P=30 P x (n-) 2.5 L2 L 3 x 2-M5 depth 5 2-M3 depth 5 V M4 depth 6 2-M5 depth 4 Piping port (plug) M5 depth R3 D, E oval hole section dimensions HD ø9.8 ø5.5 M6 depth 9 P x (n-) P=30 E 2 A-A' cross section 8 Y Dimensions table per stroke length Stroke length L L n 2 3 V W Y T0/5* RD T2/3* HD 36.5 T2/3W* RD HD 34 5

23 Dimensions (bore size: ø6) LCG Series Dimensions LCG-6 Stroke length: 75, 00, 25 (Main fixing holes in this drawing are for the 75 mm stroke.) n-main body fixing hole (Refer to A-A' cross section.) W D P=30 P x (n-) L2 L 4 x 2-M5 depth 5 V M4 depth 6 2-M5 depth 4 Piping port (plug) 4 HD P=30 P x (n-) E 8 Y Dimensions table per stroke length Stroke length L L n 4 5 V W Y T0/5* RD 7 T2/3* HD 53.5 T2/3W* RD 9.5 HD 5 6

24 LCG Series Dimensions (bore size: ø20) LCG-20 Stroke length: 0, 20, 30, 40, 50 (Main fixing holes in this drawing are for the 30 mm stroke.) RD 2-Rc/8 Piping port 2-main body fixing hole (Refer to A-A' cross section.) W A 2-M5 depth 5 Common port (plug) M5 depth D A' L2 L 3 x 2-M5 depth 5 2-M5 depth 7 V M4 depth 6 2-Rc/8 Piping port (plug) 2-R3 D, E oval hole section dimensions HD ø0 ø5.5 M6 depth 9 40 E 27 A-A' cross section 6 Y Dimensions table per stroke length Stroke length L L V W Y T0/5* RD T2/3* HD 49.5 T2/3W* RD HD 47 7

25 Dimensions (bore size: ø20) LCG Series Dimensions LCG-20 Stroke length: 75, 00, 25, 50 (Main fixing holes in this drawing are for the 00 mm stroke.) n-main body fixing hole (Refer to A-A' cross section.) W D 49.5 P=40 P x (n-) L2 L 4 x 2-5 depth 5 V M4 depth 6 2-Rc/8 Piping port (plug) 20.5 HD 9 8 P x (n-) P=40 E 6 Y Dimensions table per stroke length Stroke length L L n V W Y T0/5* RD 6 T2/3* HD 6 T2/3W* RD 8.5 HD

26 LCG Series Dimensions (bore size: ø25) LCG-25 Stroke length: 0, 20, 30, 40, 50 (Main fixing holes in this drawing are for the 30 mm stroke.) RD 2-Rc/8 Piping port W A n-main body fixing hole (Refer to A-A' cross section.) 2-Rc/8 Common port (plug) M5 depth 7 D A' 49.5 P=40 P x (n-) 5 L2 L V x 2-M6 depth 6 2-M5 depth 7 2-Rc/8 Piping port (plug) 2-R3 D, E oval hole section dimensions M8 depth 2 ø.5 ø HD M6 depth P x (n-) P=40 E 33 A-A' cross section 8.5 Y Dimensions table per stroke length Stroke length L L n V W Y T0/5* RD T2/3* HD 59 T2/3W* RD HD

27 Dimensions (bore size: ø25) LCG Series Dimensions LCG-25 Stroke length: 75, 00, 25, 50 (Main fixing holes in this drawing are for the 00 mm stroke.) n-main body fixing hole (Refer to A-A' cross section.) W D 49.5 P=40 P x (n-) 5 L2 L 4 x 2-M6 depth 6 V M5 depth 7 2-Rc/8 Piping port (plug) 9 9 HD 9 6 depth 6 P x (n-) P=40 E 8.5 Y Dimensions table per stroke length Stroke length L L n V W Y T0/5* RD 8.5 T2/3* HD 79.5 T2/3W* RD 2 HD 77 20

28 LCG Series Dimensions: Option Stopper for adjustable stroke (S to S6) For ø8 D F 2-I Piping port G E B C C 2-L Piping port H A Shock absorber stopper (A to A6) For ø8 2-I Piping port B J J 2-L Piping port A K H Note : F, H, and L dimensions apply only to that with a stopper section port (S*D*, A*D*). Note 2: The adjustable stroke range for the stopper is 5 mm on a side. Note 3: S3** to S6** and A3** to A6** are not available for that with position locking. Symbol Bore size (mm) A B C D E F G H I J K L Shock absorber type stopper Stroke adjustment range (single side) ø M3 depth M3 depth 3 9 ø M5 depth M5 depth 4 7 ø M5 depth M5 depth ø M5 depth M5 depth 4 5 ø Rc/ M5 depth 4 3 ø Rc/ M5 depth 4 0 2

29 M E M O 22

30 Linear slide cylinder double acting position locking type LCG-Q Series Bore size: ø8, ø2, ø6, ø20, ø25 JIS symbol Specifications Descriptions LCG-Q Bore size mm ø8 ø2 ø6 ø20 ø25 Actuation Working fluid Double acting Compressed air Max. working pressure MPa 0.7 Min. working pressure MPa 0.5 Withstanding pressure MPa Ambient temperature Port size Stroke tolerance -0 to 60 (to be unfrozen) Body side surface M5 Rc/8 Rear body mm None (Note ) 0 Working piston speed mm/s 50 to 500 Cushion Position locking mechanism Rubber cushioned Head end Holding force N At PULL, theoretical thrust 0.7 (at 0.7 MPa) Lubrication Not required (when lubricating, use turbine oil Class one ISOVG 32.) Allowable energy absorption J Refer to the table 3 on Page 47. Note : When not using a stopper, a slight gap may exist between the end plate and floating bushing. Stroke length Bore size (mm) ø8 0, 20, 30, 40, 50, 75 ø2 0, 20, 30, 40, 50, 75, 00 Note: Stroke length other than above is not available. Standard stroke length (mm) ø6 0, 20, 30, 40, 50, 75, 00, 25 ø20 0, 20, 30, 40, 50, 75, 00, 25, 50 ø25 0, 20, 30, 40, 50, 75, 00, 25, 50 23

31 Switch specifications /2 color indicator Descriptions Applications T0H/T0V Programmable Controller and relay Reed 2 wire T5H/T5V Programmable controller, relay IC circuit (without light), serial connection Load voltage 2/24VDC 0VAC 5/2/24VDC 0VAC Load current 5 to 50mA 7 to 20mA 50mA or less 20mA or less Light Descriptions Applications Leakage current LED (ON lighting) 0mA Without indicator light LCG-Q Series Specifications Proximity 2 wire Proximity 3 wire Proximity 2 wire Proximity 3 wire T2H/T2V T2WH/T2WV T3H/T3V T3WH/T3WV F2H/F2V F2YH/F2YV F3H/F3V F3YH/F3YV Programmable Controller dedicated Programmable Controller and relay Programmable Controller dedicated Programmable Controller and relay Output type - NPN output - NPN output Power voltage - 0 to 28V DC - 0 to 28V DC Load voltage 0 to 30V DC 24V DC 0% 30V DC or less 0 to 30V DC 24V DC 0% 30V DC or less Load current 5 to 20mA 00mA or less 50mA or less 5 to 20mA 00mA or less 50mA or less Light LED (ON lighting) Red/green LED (ON lighting) LED (ON lighting) Red/green LED (ON lighting) LED (ON lighting) Red/green LED (ON lighting) LED (ON lighting) Leakage current ma or less 0 A or less ma or less 0 A or less Red/green LED (ON lighting) Cylinder weight Position locking type (Unit: g) Bore size Basic stroke type (mm) (mm) ø ø , ø ,070,400,590,800 - ø20,50,50,50,630,750 2,70 2,460 2,760 3,050 ø25 2,450 2,450 2,450 2,60 2,80 3,620 4,040 4,460 4,90 Additional variations and options (stoppers) Bore size Option and stopper symbol (mm) S, S2 A, A2 ø ø ø ø ø (Unit: g) 24

32 LCG-Q Series How to order Without switch LCG-Q With switch 8 40 S2 LCG-Q 2 40 F2H* R ADT Symbol A Bore size 8 ø8 2 ø2 6 ø6 20 ø20 25 ø25 Descriptions Model no. A Bore size B Stroke length D Switch quantity B Stroke length (mm) Bore size (ø) Note on model no. selection Note : Use stopper parts for the adjustable stroke on page 6 when changing the adjustable stroke range. Note 2: When using a shock absorber, refer to the stopper dimensions table on page 2 for the adjustable stroke range. Note 3: Refer to stopper dimensions on page 2 for port locations. Note 4: If no stopper is provided, the standard port locations are () and (3) below. Note 5: The stopper for adjustable stroke and shock absorber stopper combination is available as a customized part. Note 6: Selectable only when using a stopper. Note 7: Refer to the selection table on page 26 for option combinations. Note 8: A** and A2** at ø8-0st or ø2 to ø25-20st or less cannot be adjusted with the standard stopper, and are available only as customized parts. <Example of model number> LCG-Q-2-40-F2H-R-ADT C Switch model no. Model: Linear slide cylinder double acting position locking type LCG-Q A Bore size : ø2 B Stroke length : 40mm C Switch model no. : Proximity and 2 wire Axial lead wire D Switch quantity : With one pc. on rod end E Other options : shock absorber type Stopper position With side or base port Material, alloy steel (nitriding) E Option Stopper position C Switch model no. Axial Radial lead wire lead wire F2H* F2V* Contact Indicator Lead wire Proximity One color 2-wire F3H* F3V* indicator type 3-wire F2YH* F2YV* 2 color 2-wire F3YH* F3YV* indicator type 3-wire T0H* T5H* T2H* T0V* T5V* T2V* Reed Proximity One color indicator type 2-wire One color 2-wire T3H* T3V* indicator type 3-wire T2WH* T2WV* T3WH* T3WV* *Lead wire length Blank 2 color m (standard) 3 3m (option) 5 5m (option) D Switch quantity R H D One on rod end One on head end Two E Option Blank No option 2-wire indicator type 3-wire S Stopper for adjustable stroke Bore size ø8 ø2 ø6 ø20 ø25 Adjustable stroke single side 5mm Note, Note 5, Note 7 S** Stopper position Stopper S2** Stopper position 2 installation position A Shock absorber type stopper Note 2, Note 5, Note 7 A** Stopper position Stopper A2** Stopper position 2 ** section Blank Port at stopper section: no port installation position D Port at stopper section: with side or base port Note 3, Note 6 Blank Stopper block material: Rolled steel T Stopper block material: Alloy steel (nitriding) Note 6

33 LCG-Q position locking type selection table (Combination with stopper for adjustable stroke and shock absorber stopper) Model no. symbol LCG-Q base LCG-Q Series How to order : Available -: Not available Option symbol Stopper for adjustable stroke Shock absorber type stopper Bore size Stroke length S S2 S3 S4 S5 S6 A A2 A3 A4 A5 A6 ø8 ø2 to ø and over to and over Option symbol D: with stopper section port and T: stopper block alloy steel (nitriding) combined as shown in the selection table above. 26

34 LCG-Q Series How to order switch If ø8 to ø2 If ø6 to ø25 SW F2H SW T2H3 Switch model no. (Page 25 item C ) Switch model no. (Page 25 item C ) How to order stopper set Stopper section and stopper for adjustable stroke or shock absorber stopper set Use when changing from standard to stopper for adjustable stroke or with shock absorber stopper LCG 2 S 2 D Bore size (Page 25 item A ) A B Stopper type S Stopper for adjustable stroke A Shock absorber type stopper Stopper installation position For stopper position or 4 2 For stopper position 2 or 3 C Port at stopper section Blank No port D With side and bottom ports Precautions for ordering stopper set S0 is included in the stopper for adjustable stroke parts for the stopper for adjustable stroke set. When installing at position or 2 (refer to page 25), add parts shown on the right based on the stoke or adjustable stroke length. Model no. symbol LCG-Q Series -: not available Discrete stopper for adjustable stroke Option symbol Adjustable stroke length (mm) Bore size Stroke length ø8 ø2 to ø25 0 S and over Addition not required S02-0 S S02 S03-30 and over Addition not required S02 S03 27

35 How to order the discrete stopper for adjustable stroke LCG-Q Series How to order Hexagon socket head set screw with urethane Use for changing the adjustable stroke range or setting to the middle stroke LCG 2 S02 Precautions for ordering discrete stopper Only when installing the discrete stopper for an adjustable stroke or discrete shock absorber stopper at installation position or 2 (refer to page 25), the combination will be as shown on the right depending on the stroke or adjustable stroke length. Bore size (Page 25 item A ) Model no. symbol LCG Series -S, S2 -A, A2 A Adjustable stroke range S0 S02 S03 Single 5mm (standard) Single 5mm Single 25mm Discrete stopper for adjustable stroke Option symbol Discrete shock Adjustable stroke length (mm) absorber type stopper Bore size Stroke length S ø8 20 and over S0 S02 - A0 ø2 to ø25 Indicate S0, S02 or S03 in A section. Note: S03 is not used for ø8. Depending on the type, the incompatible models or adjustable stroke ranges may differ from the above values. -: combination not available 0 S S02 S and over S0 S02 S03 A0 How to order the discrete shock absorber stopper Sets of shock absorber and stopper cap Use for changing from the stopper for an adjustable stroke to the shock absorber stopper. Shock absorber Stopper cap LCG 2 A0 Bore size (Page 25 item A ) Note: Some models may not be available depending on the type. Refer to page 25. Refer to page 2 for adjustable stroke range of a shock absorber type stopper. Applicable shock absorber model No. Model Shock absorber model no. LCG-8 NCK LCG-2 NCK LCG-6 NCK LCG-20 NCK LCG-25 NCK Discrete stopper block model no. display Use when changing from standard to stopper for adjustable stroke or with shock absorber stopper LCG 2 SB T Bore size (Page 25 item A ) A Stopper block SB ø8: 30 mm stroke or less ø2 to ø25: 50 mm stroke or less SB2 ø8: 40 mm stroke and over ø2 to ø25: 75 mm stroke and over B Material Blank T Stopper block material: Rolled steel Stopper block material: Alloy steel (nitriding) 28

36 LCG-Q Series Internal structure and parts list LCG-Q Y Y' Y-Y' cross section Parts list No. Parts name Material Remarks No. Parts name Material Remarks Hexagon socket head cap screw Alloy steel Zinc chromate 8 Sleeve Carbon steel Nitriding 2 End plate Aluminum alloy Alumite 9 Hexagon socket head cap screw Alloy steel Zinc chromate 3 Stopper Aluminum alloy Alumite 0 Hexagon socket head cap screw Alloy steel Zinc chromate 4 Cushion rubber (H) Urethane rubber Coil spring Steel 5 Guard Aluminum alloy 2 Stopper guard Aluminum alloy Alumite 6 Gasket Nitrile rubber 3 Stopper piston Carbon steel Nitriding 7 Joint ring ø8: stainless steel 4 Stopper packing seal Nitrile rubber ø2 to 25: chromate ø2 to 25: aluminum alloy 5 Head cover Aluminum alloy Alumite Repair parts list Bore size Repair parts number Kit No. (mm) Position locking unit repair parts Basic unit repair parts ø8 LCG-Q-8K ø2 LCG-Q-2K ø6 LCG-Q-6K 4 4 ø20 LCG-Q-20K 6 8 ø25 LCG-Q-25K Note: Basic unit repair part numbers correspond to the double acting single rod parts list on page 7. 29

37 Dimensions LCG-Q Series Dimensions LCG-Q Base head side edge 2 A B C M3 depth 3 stopper release tap Symbol Bore size (mm) A B C ø ø ø ø ø Note: Dimensions other than the above are the same as for the double acting single rod model. 30

38 Linear slide cylinder double acting acting single single rod type rod clean type clean room specifications room specifications LCG-P7* LCG-P7* Series Series Bore size: ø6, ø8, ø2, ø6, ø20, ø25 Bore size: ø6, ø8, ø2, ø6, ø20, ø25 JIS symbol Specifications Descriptions LCG-P73 Bore size mm ø6 ø8 ø2 ø6 ø20 ø25 Actuation Working fluid Double acting Compressed air Max. working pressure MPa 0.7 Min. working pressure MPa 0.5 Withstanding pressure MPa Ambient temperature -0 to 60 (to be unfrozen) (Note ) Port size Body side surface M3 M5 Rc/8 Rear body M3 M5 Rc/8 Relief port size M3 M5 Rc/8 Stroke tolerance mm +2.0 (Note 2) 0 Working piston speed mm/s 50 to 500 Cushion Lubrication Rubber cushioned Not available Allowable energy absorption J Refer to the table 3 on Page 47. Note : The maximum temperature is 50 when the switch 6 in diameter is used when installing on a steel plate. Note 2: When not using a stopper, a slight gap may exist between the end plate and floating bushing. Stroke length Bore size (mm) ø6 0, 20, 30, 40, 50 ø8 0, 20, 30, 40, 50, 75 ø2 0, 20, 30, 40, 50, 75, 00 Note: Stroke length other than above is not available. Standard stroke length (mm) ø6 0, 20, 30, 40, 50, 75, 00, 25 ø20 0, 20, 30, 40, 50, 75, 00, 25, 50 ø25 0, 20, 30, 40, 50, 75, 00, 25, 50 3

39 Switch specifications /2 color indicator Descriptions Applications T0H/T0V Programmable Controller and relay Reed 2 wire T5H/T5V Programmable controller, relay IC circuit (without light), serial connection Load voltage 2/24VDC 0VAC 5/2/24VDC 0VAC Load current 5 to 50mA 7 to 20mA 50mA or less 20mA or less Light Descriptions Applications Leakage current LED (ON lighting) 0mA Without indicator light LCG-P7* Series Specifications Proximity 2 wire Proximity 3 wire Proximity 2 wire Proximity 3 wire T2H/T2V T2WH/T2WV T3H/T3V T3WH/T3WV F2H/F2V F2YH/F2YV F3H/F3V F3YH/F3YV Programmable Controller dedicated Programmable Controller and relay Programmable Controller dedicated Programmable Controller and relay Output type - NPN output - NPN output Power voltage - 0 to 28V DC - 0 to 28V DC Load voltage 0 to 30V DC 24V DC 0% 30V DC or less 0 to 30V DC 24V DC 0% 30V DC or less Load current 5 to 20mA 00mA or less 50mA or less 5 to 20mA 00mA or less 50mA or less Light LED (ON lighting) Red/green LED (ON lighting) LED (ON lighting) Red/green LED (ON lighting) LED (ON lighting) Red/green LED (ON lighting) LED (ON lighting) Leakage current ma or less 0 A or less ma or less 0 A or less Red/green LED (ON lighting) Cylinder weight Clean room specifications (Unit: g) Bore size Basic stroke type (mm) (mm) ø ø ø , ø ,020,350,540,750 - ø20,520,520,520,640,760 2,80 2,470 2,770 3,060 ø25 2,460 2,460 2,460 2,620 2,820 3,630 4,050 4,470 4,920 Additional variations and options (stoppers) Bore size Option and stopper symbol (mm) S to S4 S5, S6 ø ø ø ø ø ø (Unit: g) 32