GTD-1C00VS14. Description: RJ45 1x1 Table Up Through Hole 10G Base-T Contact Area : 50μ Gold LED:L-Green;R-Green

Transcription

1 To: Customer P/N: UDE P/N: Description: RJ45 1x1 Table Up Through Hole 10G Base-T Contact Area : 50μ Gold LED:L-Green;R-Green Spec No. GTD Update Date 2015/7/14 Revision E Approved Checked Prepared

2 1. MECHANICAL DIMENSION 1.1 Product Dimension General Tolerance : X.X : ± 0.38 X.XX : ±

3 1.2 Recommended PCB Layout Component Side of Board All dimension tolerance are ±0.05mm unless otherwise specified - 2 -

4 1.3 Panel Cutout - 3 -

5 1.4 Standard RJ45 Plug Specification - All dimensions follow : FCC subpart F, 68,500, Figure (C)(2)(i) & (C)(2)(ii) & (C)(3)(i) IEC All plugs must be meeting the requirements of plug Go & No-Go gauge. Gauge follow : FCC subpart F, 68,500, Figure (C)(4)(i) & (C)(5)(i) - There must be no damage to Housing and Locking Latch. - There must be no nicks and cuts in cable. - Durability : 750 cycles generally - 4 -

6 2. REQUIREMENTS 2.1 Design and Construction Product shall be of design, construction and physical dimensions specified on applicable. 2.2 Material Terminal Parts ( Terminal:Underplating :50μ" min. Nickel overall ) RJ Terminal : PH. Bronze, Thickness=0.30mm Finish : Contact Area :50μ" Gold Solder Tail : 120μ" min. Mt.Tin Input Terminal : Brass, Thickness=0.35mm Finish : 120μ" min. Mt.Tin Module Terminal : Brass, Thickness=0.30mm Finish : 120μ" min. Tin Plastic Parts <UL94V-0> Housing : LCP, Black Case : PA6T, Black Spacer : PA6T,Black Shield Parts Shield : Stainless steel, Thickness=0.20mm, Pre-soldering - 5 -

7 2.3 Operating and Storage Temperature Operating Temperature : 0 C to +70 C Storage Temperature : -40 C to +85 C 2.4 RJ45 specifications Insulation Resistance : 500MΩ min. Insertion force with the latch depressed :22N max Removal force with the latch depressed : 44N max Locking Force of Plug Latch : 50N 60+/-5 sec Durability : 2500 cycles 2.5 Performance and Test Description Product is designed to meet electrical, mechanical and environmental performance requirements specified in below table. All tests are performed at ambient environmental conditions per MIL-STD-1344A and EIA-364 unless otherwise specified. 2.6 Packaging and Packing All parts shall be packaged and packed to protect against physical damage corrosion and deterioration during shipment and storage

8 3. ELECTRICAL CHARACTERISTICS 3.1 Schematic INPUT RJ45 OUTPUT TRD1+ R8 TRCT1 R7 TRD1- R9 1 : 1 75Ω C1 TRP1+ C2 TRP1- TRD2+ R2 TRCT2 R1 TRD2- R3 1 : 1 75Ω C3 TRP2+ C6 TRP2- TRD3+ R4 TRCT3 R6 TRD3- R5 1 : 1 75Ω C4 TRP3+ C5 TRP3- TRD4+ R10 TRCT4 R12 TRD4- R11 1 : 1 300Ω C7 TRP4+ C8 TRP4- IET+ R13 IETCT R15 IET- R14 1 : 1 Shield 2KV 1000pF L3 L1 Green Green L4 L2 Emitting Color λp (nm) Green ~2.6 V 10μA max

9 3.2 Transmitter filter & Receiver filter Type : Balance low pass 100Ω impedance Insertion Loss 5MHZ 200MHZ 400MHZ db Max db Max db Max 3.3 Return Loss 100MHz -24 db Min load 100Ω 200MHz -18 db Min load 100Ω 300MHz -15 db Min load 100Ω 400MHz -10 db Min load 100Ω 500MHz - 8 db Min load 100Ω 3.4 Reflected CM to Diff Conversion(REF) 50MHZ 100MHZ 200MHZ 300MHZ 400MHZ 500MHZ -30 db Min -27 db Min -24 db Min -22 db Min -21 db Min -20 db Min - 8 -

10 3.5 Reflected Diff to CM Conversion(REF) 1MHZ 100MHZ 400MHZ 500MHZ -48 db Min -35 db Min -24 db Min -24 db Min 3.6 CM to DM Conversion(REF) 50MHZ 100MHZ 200MHZ 300MHZ 400MHZ 500MHZ -48 db Min -42 db Min -36 db Min -33 db Min -30 db Min -28 db Min 3.7 CM to CM Attenuation 1MHZ 500MHZ 800MHZ 1000MHZ -22 db Min -20 db Min -20 db Min -17 db Min 3.8 Cross Talk 1 MHz -34 db Min 350 MHz -23 db Min 500 MHz -23 db Min - 9 -

11 3.9 5th channel common mode pick up Line side D CM to PHY side E diff: 1-400MHz - 7dB Max ( must be between 0dB and -7dB) KHz, 0.1V 8mA DC BIAS Input (R8-R9), Input(R2-R3), Input (R4-R5), Input(R10-R11): 160 μh min. Input (R13-R14): 40 μh min HiPot Test Input(R8-R9) Input(R2-R3) Input(R4-R5) Input(R10-R11) To Output(C1-C2) : 1500Vac 60s or 2250Vdc 60s To Output(C3-C6) : 1500Vac 60s or 2250Vdc 60s To Output(C4-C5) : 1500Vac 60s or 2250Vdc 60s To Output(C7-C8) : 1500Vac 60s or 2250Vdc 60s

12 4. ORDER INFORMATION G T D - 1 C 00 VS1 4 A B C D A. LED Code : L-Green;R-Green. <Refer to Schematic of LED> B. Mechanical Code : w/ UDE Small logo, w/ T&S Spring C. Schematics Code : VS1 : VS1 circuit D. Plating Code : Underplating Solder Tail 50μ " min. Nickel overall 120μ " min. Bright Tin 120μ " min. Matted Tin Contact Area A : Gold Flash 1 : C : 6μ " gold 6 : B : 10μ " gold D : 15μ " gold 2 : F : 30μ " gold 3 : G : 50μ " gold 4 : Gold Flash 6μ " gold 15μ " gold 30μ " gold 50μ " gold

13 5. IR REFLOW TEMPERATURE PROFILE

14 6. Revision History Issue Date Revision Comments Operator 2013/12/17 A Initial Release. Bin 2014/11/24 B Update Mechanical Drawing Ken 2014/12/4 C Update Panel Cutout Drawing Ken 2015/7/2 D Update High Frequence SPEC Jeffrey 2015/7/14 E Change General Tolerance from.x :± 0.38;..XX ± 0.25 to.x :± 0.38;..XX ± 0.20,product width from to 17.53,and update Panel Cutout Poter