Ethernet Cat 5e & Cat 6 Patch Panels

Transcription

1 Ethernet Cat e & Cat Patch Panels Copper :: RJ/IDC Models EPPE-CTE & EPPE-CAT User Manual Applys to : EPPE-CTE :: EPPE-CAT Telect, Inc., All Rights Reserved, 9- A :: telect.com

2 Ethernet Cat e & Cat Patch Panels Copper :: RJ/IDC Models EPPE-CTE & EPPE-CAT. Overview Each compact patch panel has,, or 9, unshielded, Cat e or Cat ( & 9-port only), RJ connectors on the front and corresponding IDC punchdown connectors on the rear. Telect s patch panels offer simple and efficient interconnection in 0/00/000 Base-T, Fast, and Gigabit Ethernet applications. The panel enables speedy UTP interconnections to hubs, routers, and other active equipment. The -port panel is RU the and -port is RU and the 9-port is RU. and -port panels are available with or without tracer LEDs. (Tracer versions of Cat panels are shown on the right.) Telect also offers a handy signal tracer module as an accessory for quickly mapping out the signal path from panel to panel. Telect s signal tracer module provides selectable steady or pulsing LED modes. EPPE-CAT-ILD EPPE-CAT-ILD All panels mount flush to the front or rear of any 9-in., EIA- or WECO-spaced rack. See. Parts & Accessories on page for patch cords, 0 punch-down tool, and adapter plates for -in. racks. All Telect Ethernet patch panels are RoHS compliant. EPPE-CAT-IDC EPPE-CAT-9IDC Figure - Patch Panels Telect, Inc., All Rights Reserved, 9- A :: telect.com

3 Ethernet Cat e & Cat Patch Panels Copper :: RJ/IDC Models EPPE-CTE & EPPE-CAT. Specifications Physical: -Port Dimensions Width Height Depth Weight and -Port Dimensions Width Height Depth Weight 9-Port Dimensions Width Height Depth Weight Circuit Designation (Re-writable) Panel Material Performance: 9 in. (. mm). in. (. mm).9 in. (.0 mm). lb (0. kg) 9 in. (. mm).0 in. (. mm).9 in. (.0 mm). lb (. kg) 9 in. (. mm).9 in. (.0 mm).9 in. (. mm). lb (. kg) Above each numbered, silkscreened RJ port Cold-rolled.00 steel, electrogalvanized Cat e 00MHz + Cat 0MHz + Compliance IDC Block: Type Contact Construction Operating Life Cabling Electrical: Wiring for Dielectric Withstand Voltage/Current RJ Connector: Contact Construction Contact Resistance Insulation Resistance Insertion Life Housing Meets TIA/EIA--B.- Cat e /Cat, ISO/IEC 0 & EN 0- specifications 0 punchdown Phosphor bronze, 00μ in. nickel plating 0 re-terminations, min. - AWG, solid, UTP cable TA or TB 000 VAC 0Hz 0 max., > 00 Vdc Phosphor bronze, 0μ in. gold plating Cat e - mw per contact, Cat - mw per contact 00MW 0 insertions, < 0. db of insertion loss High-impact thermoplastic, UL9V-0 rated Telect, Inc., All Rights Reserved, 9- A :: telect.com

4 Ethernet Cat e & Cat Patch Panels Copper :: RJ/IDC Models EPPE-CTE & EPPE-CAT Table - Product Comparison Chart Model No. Ports Category Tracers? EPPE-CTE-ILD Cat e EPPE-CTE-ILD EPPE-CAT-ILD Cat EPPE-CAT-ILD EPPE-CTE-IDC Cat e EPPE-CTE-IDC EPPE-CAT-IDC Cat EPPE-CAT-IDC EPPE-CAT-IDC EPPE-CAT-9IDC 9. Installation Procedure steps:. Install patch panel on rack using four thread-forming screws, supplied.. Untwist no more than 0. in. (. mm) of conductors at termination end of cable. Untwisting more may induce unwanted EMI. yes no Telect, Inc., All Rights Reserved, 9- A :: telect.com

5 Ethernet Cat e & Cat Patch Panels Copper :: RJ/IDC Models EPPE-CTE & EPPE-CAT. Push down the 0 punch-down tool all of the way to the edge of the 0 connector to install twisted pairs and trim excess, as shown in the following illustration. (Use the following table to match up conductor colors with connectors. Table - Modular Wiring Configuration Color Code TB TA White-Blue Blue White-Orange Orange White-Green Green White-Brown Brown This procedure is complete. Signal Tracer Module The signal tracer module (Model EPPE-TRCR-MOD) allows you to light up all tracer LEDs in an Ethernet circuit ostensibly to trace problems or confirm interconnections. It requires four AA batteries. Figure - Installing Twisted Pairs The device consists of a test button on the front and a three-position sliding mode switch on the side. The switch settings are Steady on with the test button continually depressed Blinking with the test button continually depressed Steady on with the test button pressed only Once for on and once for off Keystone Connector Battery Compartment Test Button Mode Switch Figure - Signal Tracer Module Telect, Inc., All Rights Reserved, 9- A :: telect.com

6 Ethernet Cat e & Cat Patch Panels Copper :: RJ/IDC Models EPPE-CTE & EPPE-CAT. Dimensions.. -port Patch Panels NOTE: Dimensions are in in. (mm). PUNCH-DOWN CONNECTOR WIRE TIE DOWN LOCATION TB CAT TA 0 TB CAT TA TB CAT TA TB CAT TA 9 REAR VIEW 9.00 [.].0 [.9] 0. [.] CIRCUIT DESIGNATION AREA. [.]. [.] CAT. [.] END VIEW 0. [.] RJ (KEYSTONE) CONNECTOR FRONT VIEW.. -port Patch Panels NOTE: Dimensions are in in. (mm). PUNCH-DOWN CONNECTOR WIRE TIE DOWN LOCATION TB CAT TA 0 TB CAT TA TB CAT TA TB CAT TA 9 TB CAT TA TB CAT TA TB CAT TA 0 TB CAT TA 9 REAR VIEW 9.00 [.].0 [.9] 0. [.] CIRCUIT DESIGNATION AREA. [.] CAT 0.0 [.] [.9]. [.] END VIEW 0. [.] RJ (KEYSTONE) CONNECTOR FRONT VIEW Telect, Inc., All Rights Reserved, 9- A :: telect.com

7 Ethernet Cat e & Cat Patch Panels Copper :: RJ/IDC Models EPPE-CTE & EPPE-CAT. Parts & Accessories Item Part number Illustration Cat e Ethernet Patch Cords (Blue) Cat Ethernet Patch Cords (Blue) EPCE-CTE-BLXX (where XX is foot-length: 0, 0, 0, 0,, 0 ft are std. Custom lengths available.) EPCE-CAT-BLXX (where XX is foot-length: 0, 0, 0, 0,, 0 ft are std. Custom lengths available.) Signal Tracer Module (Requires four AA batteries. Batteries not included.) EPPE-TRCR-MOD 9-in. to -in. Panel Rack Adapter Punch-Down Tool 9 Telect, Inc., All Rights Reserved, 9- A :: telect.com