AXICIAT VA. RANGE 11 fan sizes, diam. 500 to 1250 mm. Higher sizes, consult us.

Transcription

1 APPLICATION Extraction or introduction of non loaded air in the tertiary or industrial field, requiring greater available pressure than with a propeller fan. Standard operating temperature from 20 C to + 40 C. Car park ventilation and smoke extraction. Smoke extraction F200/120 or F400/120 1 or 2 speeds RANGE 11 fan sizes, diam. 500 to 1250 mm. Higher sizes, consult us. CONSTRUCTION Short (standard) or long (optional) dip galvanised steel sheet shell. Multi blade aluminium fan with adjustable blade angle at rest. Two part aluminium moulded hub allowing the blade angle to be set at rest. Internal motor support. Single speed three phase 230/400 V - 50 Hz or 400/690 V - 50 Hz or two speed three phase 400 V - 50 Hz motor only, IP55, directly coupled to the hub. NUMBERING fan VA fan diam. number of blades ACCESSORIES Support legs (2 parts). Protection grille. Flexible M0 sleeve. Counter flange. Sound attenuators (consult us).

2 SELECTION TABLES - AIR AT +20 C - PRESSURE 1013 HPA The air flow rates in m 3 /h must be selected in the zones corresponding to the type of fan and the available pressure in Pa. Do not select fans outside these zones. 100 Pa 150 Pa 200 Pa 300 Pa 400 Pa 500 Pa 600 Pa Example of selection You are looking for a fan with a flow rate of m 3 /h and an available pressure of 300 Pa You select a VA fan with a 3 kw motor For higher flow rates or pressures, consult us.

3 AXIAL FANS fan LAY OUT 1 : SHORT SHELL fan LAY OUT 2 : LONG SHELL 1 speed 4 P rpm Three phase 230 / 400 V - 50 Hz 2 speeds 4 / 8 P / 750 rpm Three phase 400 V - 50 Hz - DAHLANDER coupling kw IN in A kw IN in A 0,37 0,55 / 0,09 0,55 0,75 / 0,12 0,75 1,1 / 0,18 1,1 1,5 / 0,25 1,5 2,2 / 0,37 2,2 3 / 0, / 0,75 4 5,5 / 1,1 5,5 7,5 / 1,5 7,5 9 / 1, / 2, / 3,2 18,5 19 / 4, / 4,5 You have selected a VA fan, LAYOUT 1-3 kw motor - smoke extraction 2 h at 200 Fan Motor

4 AXIAL FANS 1 speed 4 P rpm Three phase 230 / 400 V - 50 Hz 2 speeds 4 / 8 P / 750 rpm Three phase 400 V - 50 Hz - DAHLANDER coupling kw IN in A kw IN in A 0,55 0,75 / 0,18 0,75 0,9 / 0,15 1,1 1,25 / 0,16 1,5 1,6 / 0,2 2,2 2,5 / 0,31 3 3,7 / 0,46 4 4,2 / 0,53 5,5 5,2 / 0,65 7,5 6,3 / 0,8 11 8,4 / 1, ,5 / 1,6 18,5 15 / ,5 / 2, / 5 25 / 6 1 speed 4 P rpm Three phase 230 / 400 V - 50 Hz 2 speeds 4 / 8 P / 750 rpm Three phase 400 V - 50 Hz - DAHLANDER coupling kw IN in A kw IN in A 0,75 0,75 / 0,16 1,1 0,9 / 0,18 1,5 1,1 / 0,26 2,2 1,5 / 0,3 3 2,2 / 0,4 4 3 / 0,6 5,5 4 / 0,8 7,5 5,5 / 1, / / 3 18,6 16,5 / 3, / 4 You wish to run a VA in smoke extraction for 2 hours 400 C, you have chosen LAY OUT 1 (short shell) : Fan Motor 3 kw 2 H 400 C Note : the power values shown above are average powers which may vary depending on the motor manufacturer. When calibrating protective devices, refer to the indications on the motor plate.

5 ENCOMBREMENT F holes G on H 4 holes P (per leg) A B C D E F G H K L M N P Q Mass maxi Specify the air flow direction when ordering. Direction AH3 : standard version. If not specified when ordering : AXICIAT supplied for direction AH3.

6 ASSEMBLY ACCESSORIES Descripiton Set of support legs For fan placed on ground Flat grille Protection grille in compliance with EC standard Motor side flat grille Motor side protection grille for lay out 1 in compliance with EC norm Automatic flap Cuts off the natural draught when the fan is stopped To be positioned on discharge side Flexible sleeve Class M0, simplifies connection with the duct. For use with the counter flange. Counter flange For simplified connection between the flexible sleeve and the duct

7 ASSEMBLY ACCESSORIES Description Suction collector Set of antivibration mounts Antivibration shock absorbers for use with support legs ELECTRICAL ACCESSORIES Description Lockable local switch 20 A maxi with position contacts 1 speed 25 A maxi in compliance with 32 A maxi CE standards 20 A maxi in compliance with 2 speeds NFS standard not fitted 32 A maxi Magnetothermal ON/OFF circuit breaker three phase 400 V from 0,12 to 2,2 kw Sealed IP 55 box three phase 400 V from 3 to 7,5 kw magnetic trigger with alarm output three phase 400 V from 9 to 12,5 kw Frequency converter Manual control or with 0/10 V signal Control kit pressostat max. motor power 4 poles in kw Input / output voltage Mechanical protection 0,18 to 0,55 0,75 1,5 IP 20 2,2 3 to 4 three phase V IP 54 5,5 IP 54 7,5 IP IP IP 54 Potentiometer for manual remote control 1 pressostat 5 A cutting power pressure range 0.2 to 3 mbar 1 pressure pick-up with 2 meters plastic tubing