CARBON SHEET. HOT ROLLED SHEETS/PICKLED & OILED HR Sheets/Pickled & Oiled thru 6-4 HSLA Sheets thru 6-4 SCS Sheet...
|
|
- Aubrey Flynn
- 7 years ago
- Views:
Transcription
1 CARBON SHEET HOT ROLLED SHEETS/PICKLED & OILED HR Sheets/Pickled & Oiled thru 6-4 HSLA Sheets thru 6-4 SCS Sheet thru 6-4 COLD ROLLED SHEETS thru 6-5 GALVANIZED SHEETS thru 6-7 GALVANNEALED SHEETS ALUMINIZED SHEETS SHEARED SHEET BLANKS TOLERANCES Alro warehouses use state-of-the-art equipment for handling orders. 6-1
2 ASTM CS TYPE B HOT ROLLED SHEETS HOT ROLLED PICKLED & OILED SHEETS A prime quality low carbon sheet suitable for forming, punching, welding, etc. Sheets will be furnished in standard mill edge unless sheared edge is specified. Hot rolled sheets are commercial quality and in most sizes temper flat to improve flatness and relieve internal stress. HIGH-STRENGTH-LOW-ALLOY (HSLA) Sheets SPECIFICATION: HR HSLA-F Temper Flat *GR 60 *16 ga is GR 50 High Strength Sheet Steels have higher strength properties along with improved formability, weldability and/or atmospheric corrosion resistance than normally obtained from conventional carbon sheet steels. These desirable properties are obtained through selected chemical composition and controlled mill processing. High strength steels lend themselves to applications where weight reduction is a major factor. SCS (Stretched Clean Surface) HR Sheet SCS is a patented process where the material is stretcher leveled, producing a dead flat product. After the material is stretched flat, it is brushed to remove the upper 2 layers of scale leaving a smooth, clean surface. The final layer of scale, which is left on the sheet, will inhibit rust without the need for oil. It can even be painted without the costly clean up required for pickled and oiled. HOT ROLLED SHEETS/ HOT ROLLED PICKLED & OILED SHEETS 6-2 Sq. Ft. Sheet Continued on next page CSB CSB P&O HSLA-F GR x X 48 x X 7 36 x X X 36 x X X 36 x X X 48 x X X X 48 x X X X 48 x X X 60 x X X 60 x X X 60 x X X 72 x X X 72 x X X 72 x X X 72 x X 8 48 x X X 48 x X X 60 x X X X SCS
3 HOT ROLLED SHEETS/ HOT ROLLED PICKLED & OILED SHEETS Sq. Ft. Sheet CSB CSB P&O HSLA-F GR x X X 48 x X X x X X 36 x X X 36 x X X 48 x X X X 48 x X X X 48 x X X 60 x X X 60 x X X 60 x X X 72 x X X 72 x X X 72 x X X 72 x X 96 x X x X X 36 x X X 36 x X X 48 x X X X 48 x X X X 48 x X X 60 x X X 60 x X X 60 x X X 72 x X X 72 x X X 72 x X X 72 x X X X 96 x X x X X 36 x X X 36 x X X 48 x X X X 48 x X X X 48 x X X 60 x X X 60 x X X 60 x X X 72 x X X X 72 x X X X 72 x X X X 72 x X X X x X X 48 x X X SCS Continued on next page 6-3
4 HOT ROLLED SHEETS/ HOT ROLLED PICKLED & OILED SHEETS Sq. Ft. Sheet CSB CSB P&O HSLA-F GR 60 SCS x X X 36 x X X 36 x X X 48 x X X X X 48 x X X X X 48 x X X X 60 x X X X 60 x X X X 60 x X X X 72 x X 72 x X 72 x X x X X 36 x X X 36 x X X 48 x X X X X 48 x X X X X 48 x X X X 60 x X X X 60 x X X X 60 x X X X x X X 48 x X X COLD ROLLED SHEETS Commercial Quality These sheets are rolled to a close thickness tolerance and possess a fine surface finish. Cold Rolled Sheets are suitable for stamping, forming and moderate drawing operations. Very desirable nickel or chrome plating results can be secured. Also, Cold Rolled Sheets provide an excellent base for baked enamel and lacquer finishes. Sq. Ft. Sheet x x x x x x Continued on next page
5 COLD ROLLED SHEETS Commercial Quality Sq. Ft. Sheet x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x Visit the Alro Web Site 6-5
6 GALVANIZED SHEETS Commercial Quality (Lock Form Quality) A continuous mill annealing and galvanizing process produces sheets with a tight, even coat of spangle that will not flake or peel in forming operations. Normally stocked in a G-90 coating weight. Sq. Ft. Sheet 7 48 x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x Continued on next page
7 GALVANIZED SHEETS Commercial Quality (Lock Form Quality) Sq. Ft. Sheet x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x
8 GALVANNEALED SHEETS Commercial Quality Galvannealed sheet is carbon steel coated with zinc on both sides by the continuous hot dip process. Immediately as the strip exits the coating bath, the zinc coating is subjected to an in-line heat treatment that converts the entire coating to a zinc iron alloy, giving the sheet a better surface for painting. Normally stocked in an A-60 coating weight. Sq. Ft. Sheet x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x Visit the Alro Web Site
9 ALUMINIZED SHEETS Commercial Quality Aluminized coated carbon steel sheets have an aluminum and silicon alloy coating on both sides. They are principally used in heat-resisting applications and also where corrosion and heat are involved. Sq. Ft. Sheet x x x x x x x x x x x x x x x x x x x x x x x x x SHEARED SHEET BLANKS Investment conscious customers rely on Alro Steel to provide them with sheared sheet blanks. A battery of shears, working around the clock, assure availability of material to meet production schedules. This results in reduced inventory and handling costs, less in-plant scrap accumulations, and provides customers with quality blanks ready for immediate processing. Contact us today and learn more about The Alro Difference! ALRO
10 HOT AND COLD ROLLED SHEET TOLERANCES MANUFACTURERS STANDARD GAGE Hot Rolled, HR P&O, Cold Rolled Galvanized, Galvannealed Tolerance Pounds Pounds Range Tolerance Equiv. Square Equiv. Range Square Gauge HR P&O CR Foot Gauge Foot Guideline only. Some products are not produced in all gauge ranges. 6-10
11 Shearing Shearing sheet metal and plate steel is performed in most of Alro s steel warehouses. We ll shear your order to your exact specifications, place your material on a skid for safe transporting and safe handling after your order is delivered to your specified location. We are capable of shearing plate up to 1/2 thick. capacities vary depending on the grade of the material. Please inquire. Sheared products are wrapped for protection and skidded for delivery. Laser Cutting Technology Laser cutting is an excellent process for carbon steel, stainless steel and aluminum. Other advantages include: High quality cuts High precision cut parts Higher speeds than precision plasma under 1/8 inch Minimal clean up Narrow kerf width Smallest heat affected zone To request a burning quote for your existing CAD drawing please send it along in an , to: burnprints@ Contact us today ALRO
12 Visit the Alro Web Site to learn more about The Alro Difference! Search ALRO (2576) Home Online Store Metals Industrial Supplies Plastics Processing Catalogs e-business News Locations Contact Careers January 05, 2015 Alro Plastics: 5-Axis Waterjet Cutting Alro's plastics processing capabilities have reached a new level of sophistication with the addition of a new Flow 5-Axis Waterjet Cutter! Waterjet - Alro Plastics SmartCell Michigan Walter/Blaxx Metals Industrial Supplies Plastics Cold Finished Bars Bronze Grinding & Sanding Fluids & Lubricants ABS Nylon Hot Rolled Bars Rebar Hole Making Die Sets & Supplies Acetals PEEK Aluminum Tool Steel Boring Punches Acrylic Plexiglas Stainless Drill Rod Threading Fasteners Cast Nylons Polycarbonate Hot Rolled Plate Flat Ground Stock Milling Machinery Delrin Polyethylene Carbon Sheet Cast Iron Turning & Grooving Hand/Power Tools Fiberglass PTFE Structural Chrome Plated Bar Reaming Material Handling Laminates TIVAR Tubing/Pipe Expanded Metal Tool Holding Shelving Makrolon Tooling Board Alloys Grating Work Holding Tool Storage Medical Grades UHMW-PE Brass Strapping Sawing Paper Products Micarta Urethane Copper Wire Mesh Shop Supplies Metals Processing Saw Cutting Flame Cutting Waterjet Cutting Shearing Plate Laser Cutting Plasma Cutting Tube Laser Cutting Press Brake/Forming Production Precision Saw Cutting Grinding Thermal Processing Precision Aluminum Plate Sawing Industrial Supply Services Calibration Chain Sling Inspection/Certification Band Saw Preventative Maintenance Band Saw Repair Band Saw Blade Welding Cutting Tool Resharpening Tool Repair (indexable tools, toolholders, etc.) Cost Savings Analysis Customer In-Plant Training Coolant Lab Testing Plastics Processing Bending & Gluing CAD/CAM CNC Routing & Machining CNC Saw Cutting Drilling and Tapping Fiberglass Saw Cutting Plastics Processing Rod and Tube Cutting Plastic Welding Waterjet Cutting (5 Axis) Contact us today ALRO
Perfection Spring & Stamping Corp. 1449 E. Algonquin Rd. Mount Prospect, IL 60056 USA www.pss-corp.com 411@pss-corp.com
Perfection Spring & Stamping Corp. 1449 E. Algonquin Rd. Mount Prospect, IL 60056 USA www.pss-corp.com 411@pss-corp.com Raw Material Type, Alloy, & Finishes By Manufacturing Method 1. Punch Press Department
More informationTARIFF CODE and updates standard
TARIFF CODE and updates standard No HS CODE AHTN CODE PRODUCT DESCRIPTION PRODUCT TYPE STANDARDS IDENTIFIED 7207 Semi finished products of iron or non alloy steel Containing by weight less than 0.25% of
More informationSpecifications for Programs: 737, 747, 757, 767, 777, 787
= Performed by GKN BAC 5000 AN General Sealing 6-262, 6-265, 6-267, 6-270 PSD for 787 Only: 6-242, 6-269, 6-271 PSD for 777 Only: 6-261,6-264, 6-266, 6-269, 6-271 BAC 5004 L Installation of Permanent Fasteners
More informationStock & Reference Guide
Stock & Reference Guide Stock & Reference Guide Boyd Metals of Fort Smith 600 South 7th Street P.O. Bo 89 Fort Smith, rkansas 72902089 (479) 7829060 Fa (479) 7823980 Fa (479) 7820424 (800) 3238806 Boyd
More informationValve Steel. Valve Steel
Valve Steel Valve Steel BÖHLER-UDDEHOLM Precision Strip AB is one of the world s leading manufacturers of high quality strip steel. More than a century s experience of cold rolling has given us a unique
More informationChapter 5 - Aircraft Welding
Chapter 5 - Aircraft Welding Chapter 5 Section A Study Aid Questions Fill in the Blanks 1. There are 3 types of welding:, and, welding. 2. The oxy acetylene flame, with a temperature of Fahrenheit is produced
More informationFLAME CuTTIng te la P is utting B c
FLAME CUTTING Both Oxy-LPG and Oxy-acetylene processes are acceptable for sectioning all thicknesses of BISPLATE. With these processes, the following techniques are recommended: Gas pressure to be the
More informationSECTION 15140 - PIPE HANGERS AND SUPPORTS
Part I - GENERAL 1.01 SECTION INCLUDES A. The work covered under this section consists of the furnishing of all necessary labor, supervision, materials, equipment, and services to completely execute the
More informationDSM http://www.dsmmfg.com 1 (800) 886-6376
DESIGN GUIDE FOR BENT SHEET METAL This guide discusses how the bends are made, what thicknesses of sheet metal are commonly used, recommended bend radius to use when modeling the part, some practical limits
More informationNingbo Yinzhou Keao Prototyping & Mould Factory Services include : CNC machining prototypes,
Ningbo Yinzhou Keao Prototyping & Mould Factory Services include : CNC machining prototypes, STEREOLITHOGRAPHY (SLA) Selective Laser Sintering (SLS) RTV MOLDING AND CAST URETHANE PROTOTYPES Tel : +86 574
More informationTABLE OF CONTENTS 2 Heavy-Wall Seamless & Welded Carbon Steel Pipe. 4 Alloy Pipe & Tube. 6 Chrome-Moly Pipe. 7 Low-Temp Pipe
PRODUCT CATALOG TABLE OF CONTENTS 2 Heavy-Wall Seamless & Welded Carbon Steel Pipe 4 Alloy Pipe & Tube 6 Chrome-Moly Pipe 7 Low-Temp Pipe 9 Services amerpipe.com 1.800.316.5737 sales@amerpipe.com 18333
More informationSTOCK LIST & BUYER S GUIDE
STOCK LIST & BUYER S GUIDE common Decimal equivalents 1/64 =.0156 1/32 =.0312 1/16 =.0625 3/32 =.0937 1/8 =.125 3/16 =.1875 7/32 =.2187 1/4 =.250 9/32 =.2812 5/16 =.3125 3/8 =.375 7/16 =.4375 1/2 =.500
More informationClaims Management Policy
Claims Management Policy INTRODUCTION ARCELORMITTAL DOFASCO CLAIMS MANAGEMENT POLICY This general claims policy covers light flat rolled sheet products produced at all ArcelorMittal Dofasco flat rolled
More informationAUSTENITIC STAINLESS DAMASCENE STEEL
AUSTENITIC STAINLESS DAMASCENE STEEL Damasteel s austenitic stainless Damascene Steel is a mix between types 304L and 316L stainless steels which are variations of the 18 percent chromium 8 percent nickel
More informationSHEET METAL DESIGN HANDBOOK
SHEET METAL DESIGN HANDBOOK Forming Basics. 2 Critical Dimensions Embosses and Offsets Bend Radius Bend Relief Forming Near Holes Form height to thickness ratio Edge Distortion Laser cutting 5 Tolerances
More informationEberl Iron Works, Inc.
Eberl Iron Works, Inc. Order Form Manual for Stair Pans, Stair Treads and Bent Plate NEW: VISIT US ONLINE AT WWW.STAIRPANS.COM Eberl Iron Works, Inc. 128 Sycamore St. Buffalo, NY 14204 Ph: 716-854-7633,
More informationSTANDARD SPECIFICATIONS SECTION 05500 METAL FABRICATIONS
STANDARD SPECIFICATIONS SECTION 05500 METAL FABRICATIONS PART 1 GENERAL 1.1 DESCRIPTION A. Section includes requirements for providing metal fabricated items like castings, gratings, hatchways, ladders,
More informationALLOY C276 DATA SHEET
ALLOY C276 DATA SHEET //// Alloy C276 (UNS designation N10276) is a nickel-molybdenum-chromium-iron-tungsten alloy known for its corrosion resistance in a wide range of aggressive media. It is one of the
More informationSECTION 15076 CEMENT-MORTAR LINED AND COATED STEEL PIPE
SECTION 15076 CEMENT-MORTAR LINED AND COATED (CML&C) STEEL PIPE PART 1 GENERAL 1.01 DESCRIPTION This section designates the requirements for steel pipe fabrication, test in shop, installation of steel
More informationNorth American Stainless
North American Stainless Flat Products Stainless Steel Grade Sheet 430 (S43000)/ EN 1.4016 Introduction: SS430 is a low-carbon plain chromium, ferritic stainless steel without any stabilization of carbon
More informationManufacturing, Supply & Quality Plan for Tower Bolts. SL Tower Bolt Market Penetration
Manufacturing, Supply & Quality Plan for Tower Bolts Project: SL Tower Bolt Market Penetration Document History Version Date Original Document First Submission Feb 9, 2013 Rev1 Requested Revisions Comments
More informationHOME RESEARCH & DEVELOPMENT SECTORS WHY PROFILES STEEL STRIP & PLATES LOGISTICAL SERVICES. Presentation. Europe. Quality.
HOME SECTORS Presentation Europe PROFILES WHY Quality United States STEEL STRIP & PLATES SERVICES Finishing Ethiopia CUSTOM-MADE PROFILES INNOVATIVE EXPERTISE Always the best one-stop-shopping solution
More informationNorth American Stainless
North American Stainless Long Products Stainless Steel Grade Sheet 2205 UNS S2205 EN 1.4462 2304 UNS S2304 EN 1.4362 INTRODUCTION Types 2205 and 2304 are duplex stainless steel grades with a microstructure,
More informationDuplex Stainless Steel Fabrication. Gary M. Carinci TMR Stainless Consultant for International Molybdenum Association
Duplex Stainless Steel Fabrication Gary M. Carinci TMR Stainless Consultant for International Molybdenum Association 1 Promoting molybdenum - as a material with superior properties and performance in a
More informationCATHODIC PROTECTION SYSTEM DESIGN
CATHODIC PROTECTION SYSTEM DESIGN Presented By DENIS L ROSSI P.E. CORROSION ENGINEER New England C P Inc. Corrosion Fundamentals What is corrosion? It is defined as the degradation or deterioration of
More informationHamilton Form Company, Ltd Custom Designs, Flexible Solutions
Hamilton Form Company, Ltd Custom Designs, Flexible Solutions 1 IFC 2 CUSTOM DESIGNS, FLEXIBLE SOLUTIONS Hamilton Form has been designing and building custom steel forms for the precast industry since
More informationFRICTION MATERIALS & BONDING SERVICES
FRICTION MATERIALS & BONDING SERVICES World Class Friction Materials & Bonding Services The Industry Leader Midwest Brake has been a leading supplier of non asbestos industrial friction material and bonding
More informationNorth American Stainless
North American Stainless Flat Products Stainless Steel Sheet T409 INTRODUCTION NAS 409 is an 11% chromium, stabilized ferritic stainless steel. It is not as resistant to corrosion or high-temperature oxidation
More informationIntroduction. ε 1 θ=55 ε 2. Localized necking Because ν=0.5 in plasticity, ε 1 =-2ε 2 =-2ε 3. ε 3,ε 2
SHEET METALWORKING 1. Cutting Operation 2. Bending Operation 3. Drawing 4. Other Sheet-metal Forming 5. Dies and Presses 6. Sheet-metal Operation 7. Bending of Tube Stock 1 Introduction Cutting and forming
More information60.12. Depend-O-Lok FxE Expansion Coupling. System No. Submitted By Spec Sect Para Location Date Approved Date. DEPEND-O-LOK FxE EXPANSION COUPLING
60.1 D-O-L FxE expansion couplings are a bolted, split-sleeve design that provides for expansion and contraction at the coupled joint. These couplings are furnished with restraint rings that, when affixed
More informationproducer of zinc, aluminium, magnesium die casting and plastic moulding
producer of zinc, aluminium, magnesium die casting and plastic moulding FAM Technika Odlewnicza is a modern producer of zinc, aluminium, magnesium die casting and plastic moulding. The Company is one of
More informationALLOY 6022 SHEET. Higher Strength with Improved Formability SUPPLYING THE WORLD S BEST
SUPPLYING THE WORLD S BEST DESCRIPTION 6022 is a heat treatable low copper, Al-Si-Mg sheet alloy developed by Alcoa to satisfy the needs of automotive manufacturers for closure panels, such as a hood,
More informationGUARDRAIL POST STEEL
GUARDRAIL POST STEEL Guardrail posts meeting materials certification are evaluated and checked for: 1. Dimensional acceptance 2. Physical test results a. Chemical b. Physical 3. Galvanized or painted coating
More informationThere is no upside to. down time
EXPANDED and PERFORATED Data and Specifications 30 Similar to Type 302 with excellent mechanical properties, resistance to many corrosive agents. Useful where sanitation and cleanliness are important.
More informationCopper-Nickel Mill Products
Copper-Nickel Mill Products Copper-Nickel Rod, Sheet, Plate, and Tubing ALASKAN COPPER & BRASS COMPANY History W hen Alaskan Copper Works was founded as a marine coppersmithing company in 9, one of its
More informationHigh-strength and ultrahigh-strength. Cut sheet from hot-rolled steel strip and heavy plate. voestalpine Steel Division www.voestalpine.
High-strength and ultrahigh-strength TM steels Cut sheet from hot-rolled steel strip and heavy plate Josef Elmer, Key account manager voestalpine Steel Division www.voestalpine.com/steel Weight savings
More informationNorth American Stainless
North American Stainless Flat Products Stainless Steel Grade Sheet 310S (S31008)/ EN 1.4845 Introduction: SS310 is a highly alloyed austenitic stainless steel designed for elevated-temperature service.
More informationCaps STANDARD WEIGHT Inches / Pounds
Standard Caps you are here: Home > Weldbend Catalog > Fittings > Caps Caps STANDARD WEIGHT Inches / Pounds For Metric Units >Click Here Nominal Pipe Size Outside Inside Wall Thickness (T) Length (E) Pipe
More informationAISI O1 Cold work tool steel
T OOL STEEL FACTS AISI O1 Cold work tool steel Great Tooling Starts Here! This information is based on our present state of knowledge and is intended to provide general notes on our products and their
More informationMueller. Pipe Repair Products. Saddles Tapping Sleeves Pipe Repair Clamps A complete selection for all types of pipe... all from a single source.
Mueller Pipe Repair Products Saddles Tapping Sleeves Pipe Repair Clamps A complete selection for all types of pipe... all from a single source. SERVICE SADDLES Mueller service saddles, available in bronze,
More informationCT-02 CABLE TRAY SYSTEMS
CT-02 CABLE TRAY SYSTEMS SYSTEMS THAT MAKE SENSE Introduction B-Line Systems was formed in 96 and has over 30 years experience manufacturing cable tray systems in which it has grown to become the industry
More informationIHSS-N1 WELDED HONEYCOMB CORE SPECIFICATION. Generated: Sergiy Papyshev Engineering. Approved: Don Prysi Manufacturing. Approved: Merzuk Ramic Quality
IHSS-N1 WELDED HONEYCOMB CORE SPECIFICATION Generated: Sergiy Papyshev Engineering Approved: Don Prysi Manufacturing Approved: Merzuk Ramic Quality Approved: Steven Barnett Administrative DATE DATE DATE
More informationSPECIFICATIONS FOR STEEL PIPE
SPECIFICATIONS FOR STEEL PIPE Published pipe standards serve three functions. 1. They dictate manufacturing and testing requirements and prescribed methods of measuring the required mechanical and physical
More informationSynergy THE O NEAL FAMILY OF COMPANIES
Synergy Family is synonymous with synergy at O Neal Industries (ONI). As part of the nation s largest family-owned group of metals service centers, each ONI company and each individual operation have the
More informationStructural Bolting. Notice the Grade 5 has a much smaller head configuration and a shorter shank then the A325 structural bolt. Rev.
Structural Bolting ASTM A325 and ASTM A490 are the two U.S. standard structural bolts. When looking at the mechanical requirements of bolts it appears that an ASTM A325 and SAE J429 Grade 5 are identical
More informationSECTION 02720 SANITARY SEWER AND STORM DRAIN SYSTEMS
SECTION 02720 SANITARY SEWER AND STORM DRAIN SYSTEMS PART 1 GENERAL 1.01 SECTION INCLUDES A. The requirements for pipe material and installation in sewer and drainage collection systems. All materials
More informationCALCULATION & DRAFTING STANDARDS MANUAL PROCEDURE: C&D 515 Bill of Materials Standard REV 0.0 5/6/04
BROWN MINNEAPOLIS TANK PAGE 1 OF 7 PURPOSE: Create and Drawing Uniformity Create, explain, and establish a standard bill of materials to be placed on every drawing (except the overall tank elevation and
More informationPIPING SYSTEM - ABRASIVE SLURRIES Engineering Standard Specification. 96 B. Riutta
PIPING SYSTEM - ABRASIVE SLURRIES Engineering Standard Specification Number: 3503-11.2.610 Rev. 2 Rubber Lined Steel Pipe and Fittings Mechanically Coupled Plain End Type System Issued Revised Approved
More informationQSTE... hot-rolled high strength cold forming sheet steel as per EN 10 149
QSTE... hot-rolled high strength cold forming sheet steel as per QStE hot-rolled high strength cold forming sheet steel Steels labelled QStE are a class of fine grain micro-alloyed thermo-mechanically
More informationTechnical Services & Capabilities
Technical Services & Capabilities Machining Welding MIG TIG Robotic TIG Friction Stir Welding Solution Heat Treat & Artificial Aging Assemblies & Fabrication Bike Frame Specialists Technical Services Product
More informationNAS: A REFERENCE IN THE STAINLESS STEEL INDUSTRY
NAS: A REFERENCE IN THE STAINLESS STEEL INDUSTRY Cristobal Fuentes CEO of NAS Investor and Analyst s Day London, 8 th November 2011 Table of Contents I. Company Overview II. Raw Materials III. Integrated
More informationEmbedded Parts Introduction - Anchors
In the plant construction or process plants such as chemical, petrochemical, gas or power plants various disciplines are brought into contact and built on each other. Civil, mechanical, electro technical
More informationFlexible Printed Circuits Design Guide
www.tech-etch.com/flex Flexible Printed Circuits Design Guide Multilayer SMT Assembly Selective Plating of Gold & Tin-Lead Fine Line Microvias Cantilevered & Windowed Leads 1 MATERIALS CONDUCTOR Copper
More informationDESCRIPTION. Stud Bolts for Pressure-Temperature Piping 2-1. General Purpose End-to-End Studs 2-2. Tap End Stud Bolts 2-3. Double End Stud Bolts 2-4
DESCRIPTION PAGE B7 Studs and Nuts Stud Bolts for Pressure-Temperature Piping 2-1 General Purpose End-to-End Studs 2-2 Tap End Stud Bolts 2-3 Double End Stud Bolts 2-4 Sigma Fasteners, Inc. Section 2 STUD
More informationFLEXIBLE CIRCUITS MANUFACTURING
IPC-DVD-37 FLEXIBLE CIRCUITS MANUFACTURING Below is a copy of the narration for DVD-37. The contents of this script were developed by a review group of industry experts and were based on the best available
More informationSection 4: NiResist Iron
Section 4: NiResist Iron Section 4 Ni-Resist Description of Grades...4-2 201 (Type 1) Ni-Resist...4-3 202 (Type 2) Ni-Resist...4-6 Stock Listings...4-8 4-1 Ni-Resist Description of Grades Ni-Resist Dura-Bar
More informationThe world leader in conveyor pulleys
The world leader in conveyor pulleys You ask. We Deliver. Chantland pulleys and rollers come in virtually any diameter, wall thickness, length, shaft size or end type. They re built from stainless steel,
More informationProducts. EschmannStahlGrades Plastic Mould Steel Hot Work Tool Steel Cold Work Tool Steel Overview
Products EschmannStahlGrades Plastic Mould Steel Hot Work Tool Steel Cold Work Tool Steel Overview High quality, Comprehensive and applicationoriented We Have the Right Solution High Quality and Quickly
More informationFlex Circuit Design and Manufacture.
Flex Circuit Design and Manufacture. Hawarden Industrial Park, Manor Lane, Deeside, Flintshire, CH5 3QZ Tel 01244 520510 Fax 01244 520721 Sales@merlincircuit.co.uk www.merlincircuit.co.uk Flex Circuit
More informationHow To Run A Test Lab In Rourkela
TESTING LABORATORY ROURKELA 1. Background: Keeping in view of the growing demand of quality of the products of the industries, Govt. has established Testing Laboratory, Rourkela, under the Directorate
More informationSeamless stainless tubes for hydraulic and instrumentation systems
Seamless stainless tubes for hydraulic and instrumentation systems stock assortment integrated production technical knowledge network of sales and service Reduce your lifecycle costs When selecting tubes
More informationJames M. Pleasants Company
James M. Pleasants Company SUBMITTAL DATA GAINESVILLE MECHANICAL DECEMBER 20, 2013 PROJECT: GSU: J-183 HUMANITIES LAW BLDG. QUOTE NO:12116 ENGINEER: STEVENS & WILKINSON GASKETED PLATE HEAT EXCHANGER Tag:
More informationGENERAL PROPERTIES //////////////////////////////////////////////////////
ALLOY 625 DATA SHEET //// Alloy 625 (UNS designation N06625) is a nickel-chromium-molybdenum alloy possessing excellent resistance to oxidation and corrosion over a broad range of corrosive conditions,
More informationNORTHFIELD METAL PRODUCTS
NORTHFIELD METAL PRODUCTS CUSTOM METAL & PLASTIC COMPONENT MANUFACTURING SINCE 1974 PROGRESS through engineering & design WHO WE ARE Northfield Metal Products, located in Waterloo Ontario Canada, has been
More informationMetal Pressfitting Pipe Systems
VdS Guidelines for water extinguishing systems VdS 2100-26-3en Requirements and test methods Part 3: Additional provisions for Pipe Systems made of galvanized steel VdS 2100-26-3en : 2012-04 (01) Publishing
More informationSECTION 08332 COILING COUNTER DOORS. Display hidden notes to specifier. (Don't know how? Click Here)
SECTION 08332 COILING COUNTER DOORS Display hidden notes to specifier. (Don't know how? Click Here) PART 1 GENERAL 1.1 SECTION INCLUDES A. Coiling Metal Counter Doors. B. Coiling Counter Fire Doors. 1.2
More informationLecture slides on rolling By: Dr H N Dhakal Lecturer in Mechanical and Marine Engineering, School of Engineering, University of Plymouth
Lecture slides on rolling By: Dr H N Dhakal Lecturer in Mechanical and Marine Engineering, School of Engineering, University of Plymouth Bulk deformation forming (rolling) Rolling is the process of reducing
More informationNorth American Stainless
Introduction: North American Stainless Flat Products Stainless Steel Grade Sheet 309S (S30908)/ EN1.4833 SS309 is a highly alloyed austenitic stainless steel used for its excellent oxidation resistance,
More informationIntroduction to JIGS AND FIXTURES
Introduction to JIGS AND FIXTURES Introduction The successful running of any mass production depends upon the interchangeability to facilitate easy assembly and reduction of unit cost. Mass production
More informationMaking Clock Wheel & Pinion Cutters
Making Clock Wheel & Pinion Cutters When making hand made clocks or in repair work an odd size cutter is sometimes needed. Sometimes just one pinion is required and does not justify the cost of a commercial
More information(Issued 1 Dec. 1965) CRD-C 45-65 METHOD OF TEST FOR THERMAL CONDUCTIVITY OF LIGHTWEIGHT INSULATING CONCRETE 1
CRD-C 45-65 METHOD OF TEST FOR THERMAL CONDUCTIVITY OF LIGHTWEIGHT INSULATING CONCRETE 1 Scope 1. This method of test covers a procedure for measuring the thermal conductivity of lightweight concrete of
More informationThe creation of tooling using the selective laser sintering process. Scott Schermer S.C. Johnson
The creation of tooling using the selective laser sintering process Scott Schermer S.C. Johnson 1 TOOLING utilizing traditional rapid prototyping machines to produce metal inserts. 2 LaserForm ST-100?
More informationHow To Write A Recipe Card
Forging stock standards guideline Issue n 10 FORGING STOCK 30 Microstructure 34 Grain size Air melted (except if δ ferrite or problem 1 per batch) 50 Cleanness/ Inclusion See EN 2157-2. 51 Macrostructure
More informationPAAM COMMERCIAL PRIVATE LIMITED
METAL PACKAGING We at Paam Group have been providing vast range of packaging products to our customers based on their preferences, needs and specifications. We provide all the materials required in metal
More informationGAS DISTRIBUTION PRODUCTS STEEL SERVICE TEES
GAS DISTRIBUTION PRODUCTS STEEL SERVICE TEES CONTINENTAL INDUSTRIES ABOUT US THE ULTIMATE CONNECTION Our Company Continental Industries, headquartered in Tulsa, Oklahoma, was formed in 1958 and is today
More informationSECTION 05 7360 ALUMINUM HANDRAIL AND RAILING SYSTEMS WITH DECORATIVE METAL PANEL INFILLS
1 SECTION 05 7360 ALUMINUM HANDRAIL AND RAILING SYSTEMS WITH DECORATIVE METAL PANEL INFILLS PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and
More informationStainless steel grade chart
Stainless steel grade chart ATLAS STEELS METAL DISTRIBUTION Chemical analysis (%) specified C Si Mn P S Cr Mo Ni Other Austenitic stainless steels 253MA S30815 0.05 1.1-2.0 0.8 0.040 0.030 20.0-22.0 10.0-12.0
More informationWire EDM Fundamentals
29 2 Wire EDM Fundamentals Revolutionizing Machining Wire Electrical Discharge Machining (EDM) is one of the greatest innovations affecting the tooling and machining industry. This process has brought
More informationCopper and Copper Alloy Tube, Pipe and Fittings
Copper and Copper Alloy Tube, Pipe and Fittings COPPER and COPPER ALLOY TUBE and PIPE Seamless Copper Pipe: Copper pipe is almost pure copper manufactured to the requirements of ASTM B 42 - Standard Specification
More informationASTM A860/A860M-09 Standard Specification for Wrought High Strength. Ferritic Steel Butt Welding Fittings. 1. Scope :- 2. Reference Documents :-
Standard Specification for Wrought High Strength Ferritic Steel Butt Welding Fittings 1. Scope :- 1.1 This specification covers wrought high strength ferritic steel butt-welding fitting of seamless and
More informationTITANIUM FABRICATION CORP.
TITANIUM FABRICATION CORP. Titanium, Zirconium, and Tantalum Clad Construction General Considerations In many applications, particularly for large pressure vessels designed for high temperature and pressure,
More informationLiftAlloy Chain Slings
CHAIN SLING BASICS Slings Lift-All chain slings meet or exceed all OSHA, ASME B30.9 and NACM standards and regulations. chain slings, available in 80 for 7/32" and 7/8"- /4" and 00 for 9/32"-3/4", are
More informationWIRE TIES FOR OVERHEAD LIFTING
Phone: (720) 554-0900 Fax: (720) 554-0909 technical@galvanizeit.org WIRE TIES FOR OVERHEAD LIFTING 1. Scope 1.1 The wire tie guideline covers common practices and procedures in the galvanizing industry
More information1.02 SYSTEM DESCRIPTION
1 OF 7 MODULAR MEZZANINES GUIDE SPECIFICATIONS FOR PART 1 - GENERAL 1.01 RELATED WORK A. SECTION 03 30 00: Cast in Place Concrete (and Concrete Finishing) 1. The area where mezzanine is installed shall
More informationTubing Data. Contents. Tubing Selection. Tubing Handling. Tubing Material. Tubing Outside Diameter Hardness. Tubing Wall Thickness
www.swagelok.com Tubing Data Contents Tubing Selection... 1 Tubing Handling.... 1 Gas Service... 2 Tubing Installation.... 2 Suggested Allowable Working Pressure Tables Carbon Steel Tubing... 3 Stainless
More informationTechCut 4 Precision Low Speed Saw
Product Brochure TechCut 4 Precision Low Speed Saw 3" - 6" Blade Range Digital Speed Display 1-Micron Sample Indexing Spring-Loaded Dressing Stick Attachment All Aluminum & Stainless Steel Construction
More informationLathe Milling Attachment
Lathe Milling Attachment By L C. MASON BY CLEVERLY stacking cold-rolled flat stock together, T-slots and slide for this lathe milling attachment are made without costly machinery. In fact, only two tools,
More informationAIRPORT SECURITY FENCING. A. American Society for Testing and Materials (ASTM):
SECTION 02832 AIRPORT SECURITY FENCING PART 1-GENERAL 1.1 SUMMARY A. Section includes: Construct airport security chain-link fence and gate at specified areas and conforming lines, grades, details indicated
More informationALLOY 2205 DATA SHEET
ALLOY 2205 DATA SHEET UNS S32205, EN 1.4462 / UNS S31803 GENERAL PROPERTIES ////////////////////////////////////////////////////// //// 2205 (UNS designations S32205 / S31803) is a 22 % chromium, 3 % molybdenum,
More informationZero peel strength of acrylic pressure sensitive adhesive is at about 45 C (-50 F).
PRODUCT BULLETIN Aluminum Polyimide Acrylic (3M 966) PSA First Surface Aluminum Coated Polyimide Tape with Acrylic 3M 966 Adhesive TAPES Sheldahl Brand Materials first surface aluminized polyimide tape
More informationAnodes and Misc Equipment
Anodes and Misc Equipment Application: Platinised Titanium Anodes Platinised titanium anodes are recommended for use in the following electrolytic processes:- Precious metal electroplating - e.g. Au, Pt,
More informationROOF DRAINS TABLE OF CONTENTS
Pictorial Index Product Recommendations Roof Drain Selection Factors Sizing Placement Material & Characteristics Pipe Connection Commonly Specified Options Typical Installations TABLE OF CONTENTS ROOF
More information2.3. Continuous Hot-Dip Galvanizing versus General (Batch) Galvanizing Rev 1.0 Jan 2011. GalvInfoNote. Introduction. Continuous Galvanizing
2. Coating Processes and Surface Treatments GalvInfoNote 2.3 Introduction Continuous Hot-Dip Galvanizing versus General (Batch) Galvanizing There are two different processes for applying a zinc coating
More informationThe Coating Machinery Experts Supplier Questionnaire
Date: Completed by: Company Data 1.1 General Data Full company name, legal form and address: Short form of company name: Country: USt. ID/ VAT Reg./ N.IVA/ NIPIC/ UID Nr./ ID TVA: Company homepage: www.
More informationTIG WELDING TIPS by Tom Bell
(This is a two-part document, with general tig welding first followed by one aluminum-specific.) TIG WELDING TIPS by Tom Bell 1. The bigger the rod, the easier it is to feed. Use larger diameter rods (3/32
More informationNorth American Stainless Long Products
North American Stainless Long Products 1 North American Stainless North American Stainless is part of the most competitive stainless steel manufacturing group in the world, Acerinox, S.A. The development
More informationCarton - Straight Link Machine Chain (Order Unit is Feet )
Straight Link Machine Individual chain links shown actual size in reference section page 44. Carton Uses: General utility; farm and animal Standard Material: Low carbon steel Standard Finish: Bright (BRT),
More informationDESIGN PROTOTYPE TOOL & DIE BUILD PRODUCTION SERVICE & SUPPORT
DESIGN PROTOTYPE TOOL & DIE BUILD PRODUCTION SERVICE & SUPPORT THE PTM ADVANTAGE PTM has been producing metal stampings since 1972. Our expertise and experience is wide ranging, to include detail part
More information