Tips for the Driver- for Passenger Door operation

Size: px

Start display at page:

Download "Tips for the Driver- for Passenger Door operation"

Aubrey Griffin
7 years ago
Views:

1 Tips for the Driver- for Passenger Door operation Passenger Door Operation Operate the pneumatic doors only when the vehicle comes to complete halt or moving not more than 3 KMPH. Start the vehicle only when the doors are completely closed or moving not more than 3 KMPH.. Passenger presses Stop Switch to signal the driver for doors operation. Driver pushes the button provided on the dash board to open / close the passenger doors, after applying parking brake. On pressing the Green button, the front door opens and closes. On pressing the Black button, the rear door opens and closes. On pressing the Red button, both the door closes( MASAT). On pressing the Red button, both the door opens and closes( HUIMIN). Front door Open / Close Rear door Open / Close Rear door Open / Close Both Door Open / Close Emergency Door Reset Rear leaf disable

2 Tips for the Driver- for Passenger Door operation On pressing the Disable button, only the front leaf of front door opens and rear leaf of front door remains closed. Emergency Door reset Rear leaf disable Rear Door Open/ Close Front door Open / Close Rear door Open / Close Both Door Open / Close Light on the dash board blinks and the door open audio warning sounds until the passenger doors are securely closed.

3 Ramp Operation Tips for the Driver for Ramp operation Apply Parking brake, while operating Ramp. Ramp operation is to be done manually at specified halt zones for up-loading wheel chairs. Vehicle should only be started after the Ramp is put inside and Ramp engaged warning indicator lamp is Off.

4 Tips for the Driver for AC Operation Air conditioning controllers Buttons 1. Numeric Display 2. Ventilation Control key (VENT) 3. Cooling Control Key ( AUTO) 4. Refresh control key ( RENOV) 5. Key (INCREASE) 6. Key (DECREASE) 7. Key internal/external temperature check Indicator lights 8. Indicator cooling mode 9. Indicator automatic mode 10. Indicator ventilation mode low velocity 11. Indicator ventilation mode high velocity 12. Indicator refreshment mode off 13. Indicator refreshment mode on 14. Indicator internal/external temp checking

5 Tips for the Driver for AC Operation Auto mode By pressing the key AUTO the system will control all the available functions automatically and searches for better climatic conditions with respect to the set point temperature. To disable press again the key AUTO. Cooling Mode If the internal temperature of the vehicle is above the set-point then the equipment will start operate in the COOLING MODE automatically. In this mode the evaporator s blower will start automatically but the ventilation velocity can be changed manually. Ventilation Mode By pressing the key VENT the ventilation mode will start to operate at low velocity. To select high velocity once again press the key VENT. To turn the ventilation mode off once again press the key VENT. When the AUTO MODE is on the ventilation velocity is usually automatic.

6 Tips for the Driver for AC Operation Roof heating In AUTO MODE if the internal temperature of the vehicle is below the set-point then the equipment will initiate operating in the ROOF HEATING MODE. For this manual heating valve in engine compartment should be ON Air refreshment In the AUTO MODE the refreshment will work according to the set-point temperature in both the cooling mode and heating mode. The air refreshment can be manually activated by pressing the key RENOV. It will work for 10 seconds and will close automatically, going back to auto mode. Internal and external temperature By pressing the key TEMP the display will show the external temperature for 5 seconds an after this the display will return to the show internal temperature. Programming the set-point To program the set-point temperature press the key INCREASE or DECREASE until the desired temperature is found. For 5 seconds the display keeps blinking and when it stops blinking the new internal temperature is reprogrammed. Safety features The controller on the dashboard is equipped with an failure system monitor. When there is any system failure occurred then a message is displayed.

7 Tips for the Driver for AC Operation. Driver overhead AC Blower Speed control Demister Blower Speed control Before starting the air conditioning system, the following should be checked. All belts are tight. All rotating parts are free from obstruction ( Ex: Fan & Belts) Open heater valve during cold climates

8 Calibration of Gas Leak Sensor

9 Tips for the Driver for Destination Indication Board ( MobiTec ) Guidelines for Drivers (MobiTec Destination System) When starting the Engine, the power of Display boards should h ld b be iin switched it h d OFF mode. d ICU The USB port should always be capped with the Cap provided, the Cap should only be removed whenever the USB Stick is inserted and thereafter the Cap should be placed back on the port. Do not Play with any keys of the ICU in the running condition of Bus, it may cause the ICU to get hung or any other th irreparable i bl damage d to t the th ICU. ICU Before switching off the engine, firstly switch off the power of the Display boards. After switching on the power of the ICU, do not press any key until the display on ICU screen appears. Display board switch ICU

10 Tips for the Driver for Destination Indication Board (MobiTec)

11 Tips for the Driver for Destination Indication Board (MobiTec)

12 Tips for the Driver for Destination Indication Board (MobiTec)

13 Tips for the Driver for Destination Indication Board (MobiTec)

14 Tips for the Driver for Destination Indication Board (MobiTec)

15 Tips for the Driver for Destination Indication Board (MobiTec)

Multi-information Display (see MID )

Driving Position Memory (see Seats ) Power Mirrors (see Mirrors ) Indicators/Gauges (see Instrument Panel ) Multi-information Display (see MID ) HomeLink (see HomeLink ) Navigation System (see Navigation