THERMO KING TRUCK & TRAILER UNIT ALARM CODES THIS DOCUMENT SHOWS ALL CURRENT ALARM CODES FOR THERMO KING TRUCK AND TRAILER UNITS.
|
|
|
- Camilla Butler
- 7 years ago
- Views:
Transcription
1 THERMO KING TRUCK & TRAILER UNIT ALARM CODES THIS DOCUMENT SHOWS ALL CURRENT ALARM CODES FOR THERMO KING TRUCK AND TRAILER UNITS. NOT ALL CODES ARE POSSIBLE ON ANY INDIVIDUAL UNIT. IF THE ALARM APPLIES TO A MULTI-TEMP ZONE, THAT ZONE WILL BE IDENTIFIED. BE SURE TO RECORD ALL ALARMS THAT OCCUR. THEY ARE VALUABLE TO THE SERVICE TECHNICIAN. ALARMS MARKED WITH AN ASTERISK (*) MAY EXIST WITH ALARM CODE 84. THESE ALARMS MAY CLEAR AUTOMATICALLY. COLOR CODE DEFINITIONS OK TO RUN CHECK AS SPECIFIED TAKE IMMEDIATE ACTION 00 No Alarms Exist No action required. 01 Microprocessor Power Up Reset No action required. 02 Check Evaporator Coil Sensor Manually monitor load temperature. Report this alarm at the end of the day. 03 Check Return Air Sensor Manually monitor load temperature. Report this alarm at the end of the day. 04 Check Discharge Air Sensor Manually monitor load temperature. Report this alarm at the end of the day. 05 Check Ambient Temp Sensor Report this alarm at the end of the day. 06 Check Coolant Temp Sensor Report this alarm at the end of the day. 07 Check Engine RPM Sensor Report this alarm at the end of the day. 08 Unit Running on Coil Sensor Manually monitor load temperature. Report this alarm at the end of the day. 09* High Evaporator Temperature If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 10* High Discharge Pressure (or Temperature) If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 11 Unit Controlling on Alternate Sensor Manually monitor load temperature. Report this alarm at the end of the day. 12 Sensor or Digital Input Shutdown The unit (or zone) is no longer able to operate and has been shut down. Repair immediately. 13 Sensor Check Manually monitor load temperature. Report this alarm at the end of the day. 14 Defrost Terminate by Time Report this alarm at the end of the day. 15 Check Glow Plugs or Intake Air Heater If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 16 Manual Start Not Completed Report this alarm at the end of the day. 17* Engine Failed to Crank If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 18* High Engine Coolant Temperature If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 19* Low Engine Oil Pressure If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 20* Engine (Vapor Motor CR) Failed to Start If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 21* Cooling Cycle Check Manually monitor load temperature. Report this alarm at the end of the day. 22* Heating Cycle Check Manually monitor load temperature. Report this alarm at the end of the day. 23* Cooling Cycle Fault The unit (or zone) is no longer able to operate and has been shut down. Repair immediately. 24* Heating Cycle Fault The unit (or zone) is no longer able to operate and has been shut down. Repair immediately. 25 Alternator Check If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 26* Check Refrigeration Capacity Manually monitor load temperature. Report this alarm at the end of the day. 27* Vapor Motor RPM High (CR) If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 28 Pretrip or Self Check Abort Report this alarm at the end of the day. 29 Defrost Damper Circuit Check Manually monitor load temperature. Report this alarm at the end of the day. 30 Defrost Damper Stuck Closed The unit is no longer able to operate and has been shut down. Repair immediately. Page 1
2 31 Check Oil Pressure Switch If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 32 Refrigeration Capacity Low The unit (or zone) is no longer able to operate and has been shut down. Repair immediately. 33 Check Engine RPM Report this alarm at the end of the day. 34 Check Modulation Circuit Manually monitor load temperature. Report this alarm at the end of the day. 35 Check Run Relay Circuit If the unit shuts down on this alarm code repair immediately. 36* Electric Motor Failed to Run If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 37 Check Engine Coolant Level Report this alarm at the end of the day. 38 Electric Phase Reversed If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 39 Check Water Valve Circuit Manually monitor load temperature. Report this alarm at the end of the day. 40 Check High Speed Circuit If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 41 Check Engine Coolant Temp Report this alarm at the end of the day. 42 Unit Forced to Low Speed Report this alarm at the end of the day. 43 Unit Forced to Low Speed Modulation Report this alarm at the end of the day. 44 Check Fuel System If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 45 Check Hot Gas or Hot Gas Bypass Circuit If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 46 Check Air Flow Manually monitor load temperature. Report this alarm at the end of the day. 47 Remote Sensor Shutdown The unit (or zone) is no longer able to operate and has been shut down. Repair immediately. 48 Check Belts or Clutch If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 49 Reserved for CR 50 Reset Clock Report this alarm at the end of the day. 51 Check Shutdown Circuit If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 52 Check Heat Circuit If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 53 Check Economizer Valve Circuit If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 54 Test Mode Timeout Clear this alarm and restart the unit. 55 Check Engine Speeds Report this alarm at the end of the day. 56 Check Evaporator Fan Low Speed Report this alarm at the end of the day. 57 Check Evaporator Fan High Speed Report this alarm at the end of the day. 58 Check Condenser Fan Low Speed Report this alarm at the end of the day. 59 Check Condenser Fan High Speed Report this alarm at the end of the day. 60 Check Boost Circuit If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 61 Low Battery Voltage If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 62 Ammeter Out of Calibration If the unit shuts down on this alarm code repair immediately. 63* Engine or Vapor Motor Stopped If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 64 Pretrip Reminder Report this alarm at the end of the day. 65 Abnormal Temperature Differential If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 66 Low Engine Oil Level If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 67 Check Liquid Line Solenoid Circuit If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 68 Internal Controller Fault Code Report this alarm at the end of the day. 69 Check Remagnetization Circuit If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. Page 2
3 70 Hourmeter Failure Report this alarm at the end of the day. 71 Hourmeter 4 Exceeds Set Time Limit Report this alarm at the end of the day. 72 Hourmeter 5 Exceeds Set Time Limit Report this alarm at the end of the day. 73 Hourmeter 6 Exceeds Set Time Limit Report this alarm at the end of the day. 74 Controller Reset to Defaults Report this alarm at the end of the day. 75 Controller RAM Failure If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 76 Controller EPROM Failure If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 77 Controller EPROM Checksum Failure If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 78 Data Log EPROM Failure If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 79 Internal Data Logger Overflow Report this alarm at the end of the day. 80 Check Compressor Temp Sensor Report this alarm at the end of the day. 81 High Compressor Temp Report this alarm at the end of the day. 82 High Compressor Temp Shutdown If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 83 Low Engine Coolant Temp Manually monitor load temperature. Report this alarm at the end of the day. 84 Restart Null Report this alarm at the end of the day. 85 Forced Unit Operation Report this alarm at the end of the day. 86 Check Discharge Pressure Sensor Report this alarm at the end of the day. 87 Check Suction Pressure Sensor Report this alarm at the end of the day. 88 Reserved for CR 89 Check Electronic Throttling Valve Circuit If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 90 Electric Overload If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 91 Check Electric Ready Input If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 92 Sensor Grades Not Set Report this alarm at the end of the day. 93 Low Compressor Suction Pressure If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 94 Check Loader #1 Circuit If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 95 Check Loader #2 Circuit If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 96 Low Fuel Level If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 97 Failed Remote Return Air Sensor (CR) Report this alarm at the end of the day. 98 Check Fuel Level Sensor Report this alarm at the end of the day. 99 High Compressor Pressure Ratio If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 100* Heater Fan Failure (CR) If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 101 Controlling on Evap Coil Outlet Temp (CR) Manually monitor load temperature. Report this alarm at the end of the day. (WAS 94) 102* Low Evaporator Coil Temperature (CR) If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 103 Low Heater Fuel Level (CR) Manually monitor load temperature. Report this alarm at the end of the day. 104 Check Remote Fan Speed Manually monitor load temperature. Report this alarm at the end of the day. 105 Check Receiver Tank Press Sol Circuit If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 106 Check Purge Valve Circuit If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 107 Check Condenser Inlet Sol Circuit If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 108 Door Open Timeout Close doors. Report this alarm at the end of the day. Page 3
4 109 Check High Discharge Pressure Sensor Replaced by Alarm Code Check Suction Line Sol Circuit If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 111 Unit Not Configured Correctly Report this alarm at the end of the day. 112 Check Remote Fans If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 113 Check Electric Heat Circuit Manually monitor load temperature. Report this alarm at the end of the day. 114 Multiple Alarms - Can Not Run The unit (or zone) is no longer able to operate and has been shut down. Repair immediately. 115 Check High Pressure Cut Out Switch If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 116 Check High Pressure Cut In Switch Report this alarm at the end of the day. 117 Auto Switch from Diesel to Electric Normal operation does not affect performance. 118 Auto Switch from Electric to Diesel Normal operation does not affect performance. 119 Reserved for CR 120 Check Alternator Excite Circuit If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 121 Check PMW Liquid Injection Circuit If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 122 Check Diesel/Electric Circuit If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 123 Check Evap Coil Inlet Temp Sensor Manually monitor load temperature. Report this alarm at the end of the day. 124 Check Evap Coil Outlet Temp Sensor Report this alarm at the end of the day. 125 Check Tank Level Sensor If the unit shuts down on this alarm code repair immediately. Otherwise, report this alarm at the end of the day. 126 Check Back Pressure Regulator Manually monitor load temperature. Report this alarm at the end of the day. 127 Setpoint Not Entered Be sure the setpoint is adjusted to the required temperature. 128 Engine Run Time Maint Reminder #1 Report this alarm at the end of the day. 129 Engine Run Time Maint Reminder #2 Report this alarm at the end of the day. 130 Electric Run Time Maint Reminder #1 Report this alarm at the end of the day. 131 Electric Run Time Maint Reminder #2 Report this alarm at the end of the day. 132 Total Unit Run Time Maint Reminder #1 Report this alarm at the end of the day. 133 Total Unit Run Time Maint Reminder #2 Report this alarm at the end of the day. 134 Controller Power On Hours Report this alarm at the end of the day. 135 Check Spare Digital Inputs Report this alarm at the end of the day. 136 Check Spare Digital Outputs Report this alarm at the end of the day. 203 Check Redundant Return Air Sensor Manually monitor load temperature. Report this alarm at the end of the day. 204 Check Redundant Discharge Air Sensor Manually monitor load temperature. Report this alarm at the end of the day. Page 4
5 Revision History Rev 5 06 Oct 2003 Add Code 65 Page 5
V-MAC III Fault Assignments
V-MAC III Fault Assignments ELECTRICAL FAULTS Stp Circuit Failure Blink Sequence 4 Engine Oil Pressure Low Voltage / Open 1 1 P 100 4 128/143 4 Engine Oil Pressure High Voltage 1 1 P 100 3 128/143 9 Barometric
sip Sanyo Modbus Guide Technical Specification Pinouts, Cable Connections & Wiring Issue 2: February 2009 Synapsys Solutions Ltd, all rights reserved
Sanyo Section : Section : Section : Section : Section : sip Modbus Guide Configuration Modbus Table Technical Specification Pinouts, Cable Connections & Wiring Alarm Fault Codes Issue : February 009 Section
Indoor coil is too warm in cooling mode or too cold in heating mode. Reversing valve or coil thermistor is faulty
Codes Room Air Conditioner range: Indoor unit alarm s If timer lamp flashes for 1 second on, 1 second off, this indicates pre heating on the coil during heating mode and is not an error. If timer lamp
Diagnostic Fault Codes For Cummins Engines
Section - Diagnostic Fault Codes For Cummins Engines Applies to Engine Models T, T, QSL T, QSM, QS, QSK9, QSK, QST, QSK//8 Note: These fault codes are current at date of publication. Always refer to engine
MP-4000 Alarm List (Software version 2.4.3 or later)
Service Bulletin SUBJECT: MP4000 Alarm s BULLETIN: C 100 DATE: June 19, 2013 ALARM LIST Where it is possible the alarm number is kept the same as for MP-3000. MP-3000 holds alarm number from 0 to 127.
Table V. Troubleshooting Checklist for Refrigeration Systems. Air or non-condensable gas in system. Inlet water warm.
Table V Troubleshooting Checklist for Refrigeration Systems TROUBLE POSSIBLE CAUSE CORRECTIVE MEASURE High condensing pressure. Low condensing pressure. Air or non-condensable gas in system. Inlet water
Note: This information obtained from internet sources and not verified- use at your own risk!!!!
Cummins Engine Diagnostic Fault Codes for 2003 and later engines (generally for 2004 and later Alpines; see page 13 for earlier engine diagnostic codes): Note: This information obtained from internet sources
Fault codes DM1. Industrial engines DC09, DC13, DC16. Marine engines DI09, DI13, DI16 INSTALLATION MANUAL. 03:10 Issue 5.0 en-gb 1
Fault codes DM1 Industrial engines DC09, DC13, DC16 Marine engines DI09, DI13, DI16 03:10 Issue 5.0 en-gb 1 DM1...3 Abbreviations...3 Fault type identifier...3...4 03:10 Issue 5.0 en-gb 2 DM1 DM1 Fault
Failure code manual. content
Failure code manual content 一 wall split AC series 2 二 floor standing AC series. 4 三 portable AC series.. 5 四 dehumidifer 6 五 DC inverter single split series...7 六 DC inverter multi-split series 10 1 一
Cat Electronic Technician 2015C v1.0 Product Status Report 2/16/2016 9:19 AM
Cat Electronic Technician 2015C v1.0 Product Report 2/16/2016 9:19 AM Product Report Product ID Comments Unavailable H2A00626 3054 M313C (CRX13565) H2A00626 Engine Serial Number CRX13565 ECM Serial Number
AIR COOLED CHILLER CHILLED WATER PUMP CONTROL: The chilled water pump with the lowest runtime will automatically start when the outside air temperature rises above the system enable setpoint. When the
Cat Electronic Technician 2015A v1.0 Product Status Report 6/3/2015 4:41 PM
Cat Electronic Technician 2015A v1.0 Product Status Report 6/3/2015 4:41 PM Product Status Report Parameter Product ID Equipment ID Comments Value DHK00407 Machine Control 320D/323D (DHK00407) Parameter
Cat Electronic Technician 2015A v1.0 Product Status Report 4/20/2016 2:49 PM
Page 1 of 19 Cat Electronic Technician 2015A v1.0 Product Status Report 2:49 PM Product Status Report Parameter Value Product ID WRK00337 Equipment ID WRK00337 Comments A01-52 C9 330D (THX37891) Parameter
ON-Board Diagnostic Trouble Codes
ON-Board Diagnostic Trouble Codes The list below contains standard diagnostic trouble codes (DTC s) that are used by some manufacturers to identify vehicle problems. The codes provide below are generic
Signature and ISX CM870 Electronics
Signature and ISX CM870 Electronics Cummins West Training Center System Description General Information The Signature and ISX CM870 engine control system is an electronically operated fuel control system
HEATER, AIR CONDITIONING AND VENTILATION
55-1 GROUP 55 HEATER, AIR CONDITIONING AND VENTILATION CONTENTS GENERAL DESCRIPTION 55-2 HEATER AND AIR CONDITIONING SYSTEM 55-4 HEATER CONTROL 55-6 A/C-ECU 55-7 A/C COMPRESSOR 55-9 CONDENSER 55-9 DUCT
Cat Electronic Technician 2015C v1.0 Product Status Report 2/20/2016 4:34 PM
Cat Electronic Technician 2015C v1.0 Product Status Report 2/20/2016 4:34 PM Product Status Report Parameter Product ID Equipment ID Comments Value JGB00714 NOT PROGRAMMED Machine Control 345D (JGB00714)
Air conditioning, electrical testing
just a test. Air conditioning, electrical testing 01-253 Wire and component test using VAG1598 A test box Special tools and equipment VAG 1598 A test box and VAG 1598/11 adapter cable and VAG 1598/12 VAG1526
01-3 0000-00 6810-20 AIR CONDITIONING SYSTEM 1. FFH SPECIFICATION AIR CONDITIONING SYSTEM RODIUS 2004.09
0000-00 01-3 6810-20 1. FFH SPECIFICATION 01-4 0000-00 2. SYSTEM LAYOUT AND COMPONENTS 0000-00 01-5 01-6 0000-00 3. FFH GENERAL INFORMATION The system is to increase the coolant temperature quickly by
SAS light Check Engine Malfunction Indicator Lamp
SAS light Check Engine Malfunction Indicator Lamp Here's how to do it: In car ECM Diagnostics/ECM Reset procedure: 1) Sit in the driver's seat. 2) Turn the ignition key to the ON position and wait three
A/C-HEATER SYSTEM - AUTOMATIC
A/C-HEATER SYSTEM - AUTOMATIC 1995 Volvo 850 1995-96 Auto. A/C-Heater Systems Volvo 850 * PLEASE READ THIS FIRST * WARNING: To avoid injury from accidental air bag deployment, read and carefully follow
DTC Database (OBD-II Trouble Codes)
Auto Consulting S.a.s di Cofano A. & C. Attrezzature diagnostiche Elaborazioni elettroniche Formazione tecnica DTC Database (OBD-II Trouble Codes) Definitions for generic powertrain diagnostic trouble
Air Conditioning System
Air Conditioning System 1 Chonan Technical Service Training Center Chonan Technical Service Training Center 2 Objectives To understand the components of air conditioning system. To understand the control
SMM. Installation Operation Maintenance
SMM Configuration SMM Module for Scroll Units, H Generation Installation Operation Maintenance 1 0 L80 IM 022 GB SMM Configuration SMM Module for Scroll Units, H generation Foreword These installation,
HP 5 Microprocessor Control for Mammoth Water Source Heat Pumps
HP 5 Microprocessor Control for Mammoth Water Source Heat Pumps Operation and Maintenance Manual Model: 71028004 Applies to: Single Circuit Water-to-Water Twin Circuit Units Without DDC Controls MAMM WHSP
A/C refrigerant system, overview
Page 1 of 19 87-18 A/C refrigerant system, overview A/C refrigerant system, identification Typical A/C refrigerant system with expansion valve and receiver drier 1 - Evaporator 2 - Expansion valve 3 -
Basic Technology Series
Basic Technology Series Fundamentals of Car Air Conditioning 2007 Air Conditioning #003 The Rear Cooler Construction Fan Fan Filter Figure A : Trunk Figure B : Overhead Dual Air-Conditioner In This Issue
AUTOMATIC CONTROL HEATING, VENTILATION AND AIR CONDITIONING SYSTEM
SECTION 7D AUTOMATIC CONTROL HEATING, VENTILATION AND AIR CONDITIONING SYSTEM TABLE OF CONTENTS Description and Operation... 7D- General... 7D- FATC Control... 7D- FATC Input/Output Routing Diagram...
PANASONIC TROUBLE SHOOTING GUIDE
A General Guide To Room Style Products Pipework Pipe sizes and lengths should be as the relevant Technical Guide Both lines should be insulated No line accessories or oil traps should be fitted In cooling
MAINTENANCE INSTRUCTIONS. Thermia Robust heat pump
MAINTENANCE INSTRUCTIONS Thermia Robust heat pump 9 6 8 0-5 4 7 4 5 0 0 1 R e v. 3 Table of contents 1 Important information.................. 2 1.1 Product description....................... 2 1.2 General................................
Programmable Thermostat MODEL 3312026.XXX With Dehumidify 3312024.XXX With Out Dehumidify
Comfort Control Center 2 Thermostat Operating Instructions Programmable Thermostat MODEL 3312026.XXX With Dehumidify 3312024.XXX With Out Dehumidify TABLE OF CONTENTS About your new thermostat Features...2
SECTION 15750 PACKAGED ROOFTOP AIR CONDITIONING UNITS
SECTION 15750 PART 1 - GENERAL 1.01 DESCRIPTION A. Section includes requirements for roof mounted, self-contained units, with electric cooling, and electric or reverse refrigeration cycle (heat pump) heating
Table Z. Troubleshooting Chart for Air Conditioners. Cause
Troubleshooting Chart for Air Conditioners Type of Unit Complaint Cause With open-type compressor Electric motor will not start Power failure Check circuit for power source Compressor stuck Locate cause
HVAC SYSTEM (HEATER, VENTILATOR, AND A/C)
HVAC SYSTEM (HEATER, VENTILATOR, AND A/C) HEATER SYSTEM 1. Heater System A: GENERAL A semi-center type integrated air conditioning unit is used, where a high performance heater core and an evaporator core
National Grid Small Business Energy Efficiency Program Overview. Central New York Energy Expo March 30, 2010
National Grid Small Business Energy Efficiency Program Overview Central New York Energy Expo March 30, 2010 Agenda National Grid Cooler Retrofit Program Refrigeration 101 Smart Thermostat Controls, Anti-Sweat
Heater and Air Conditioner, Blend Air System, Troubleshooting 83.06
A/C Performance Diagnosis Problem Warm Airflow When the Air Conditioner is On, A/C Not Working, or Poor A/C Performance (dash outlet temperature is too high) Problem Warm Airflow When the Air Conditioner
CDS TROUBLESHOOTING SECTION I. VACUUM. 1.0. Weak vacuum at wand. Gauge reads normal (10hg to 14hg)
CDS TROUBLESHOOTING SECTION I. VACUUM 1.0. Weak vacuum at wand. Gauge reads normal (10hg to 14hg) 1.1. Clogged hoses or wand tube. Disconnect hoses and carefully check for an obstruction. 1.2. Excessive
Why and How we Use Capacity Control
Why and How we Use Capacity Control On refrigeration and air conditioning applications where the load may vary over a wide range, due to lighting, occupancy, product loading, ambient weather variations,
543-0032-00, 943-0032-00. User s Manual
543-0032-00, 943-0032-00 User s Manual 1 Comfort Alert Diagnostics Faster Service And Improved Accuracy The Comfort Alert diagnostics module is a breakthrough innovation for troubleshooting heat pump and
Commercial Refrigeration Temperature and Defrost Controls
Commercial Refrigeration Temperature and Defrost Controls UNI-LINE PRODUCT KNOWLEDGE 2010 Invensys. All Rights Reserved. The names, logos, and taglines identifying the products and services of Invensys
R22. K Control. Indoor Unit. Nomenclature. Compatibility PL H 3 G K H B. Unit style Heat Pump Horse Power
R22. K Control. Indoor Unit. Nomenclature. PL H 3 G K H B Compatibility Unit style Heat Pump Horse Power Control Boost Heaters R22. K Control. Outdoor Unit. Nomenclature. PU H 3 Y K A Compatibility Outdoor
Section 7. Evaporator thermistor. Under-and-over pressure safety switches. Connections to the ECU
Automatic Temperature Control Diagnosis and Repair Diagnosis of Automatic A/C Systems The most common automatic A/C system malfunctions tend to be the result of basic air conditioning problems. These problems
Bus Air Conditioning and Heating Unit
Bus Air Conditioning and Heating Unit Rearmount 68RM40-108 68RM40-118 68RM40-128 (with Electronic Thermostat) OPERATION AND SERVICE MANUAL BUS AIR CONDITIONING AND HEATING UNIT Rearmount 68RM40-108 68RM40-118
Features and Benefits
Refrigeration 2 eatures and Benefits Based on IR32 Parameters Real Time lock ( RT ) Model Specific (defrost based on real time 7 day 24 hour) HAP (Hazard Analysis and ritical ontrol Point) Alarm Available
SECTION 23 81 03 - PACKAGED ROOFTOP AIR CONDITIONING UNITS NON-CUSTOM
SECTION 23 81 03 - PACKAGED ROOFTOP AIR CONDITIONING UNITS NON-CUSTOM PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Packaged rooftop air conditioning unit (5 tons and smaller). 2. Roof curb. 1.2
AIR CONDITIONING LIFE EXTENDER ACX10 FIELD INSTALLATION AND PERFORMANCE EVALUATION
AIR CONDITIONING LIFE EXTENDER ACX10 FIELD INSTALLATION AND PERFORMANCE EVALUATION Tony Thorne Manager of Electrical Engineering Index Sensors and Controls, Stanwood, WA 98292 USA ABSTRACT Air conditioning
Section 6. Introduction to Automatic A/C. Automatic Temperature Control
Automatic Control Introduction to Automatic A/C The heating, ventilation and air conditioning (HVAC) system in a house contains a wall-mounted thermostat to control outlet temperatures, distribution and
2013 Tier 4 Compliant. High capacity and reliability. Low fuel consumption and noise. Let Vector units energize your bottom line.
2013 Tier 4 Compliant High capacity and reliability. Low fuel consumption and noise. Let Vector units energize your bottom line. TURNING TIER 4 COMPLIANCE INTO A BETTER MULTI-COMPARTMENT MODEL. Carrier
Training Syllabus to Instruct/Prepare for the ASE Transit Bus HVAC Test
APTA STANDARDS DEVELOPMENT PROGRAM RECOMMENDED PRACTICE American Public Transportation Association 1666 K Street, NW, Washington, DC, 20006-1215 APTA BTS-BMT-RP-001-10 Approved October, 2010 APTA Bus Maintenance
TSB #: 74 Date: 9/7/2013 HOLDEN VE/WM HVAC & A/C DIAGNOSTIC HINTS
HOLDEN VE/WM HVAC & A/C DIAGNOSTIC HINTS TSB #: 74 Date: 9/7/2013 Initial Once Read: In this technical bulletin we have listed diagnostic advice relating to the Holden VE/WM HVAC & A/C system. This information
PROCEDURES FOR SELF DIAGNOSTICS
PROCEDURES FOR SELF DIAGNOSTICS Baum Tools Unlimited Inc. March 31, 1999 TAU 2.1 READING ACTUAL VALUES 1. Remove the operating console from the TAU 2. At the upper side of the operating consol there is
ENGINE DIAGNOSTICS & CONTROL
ENGINE DIAGNOSTICS & CONTROL CONTROL SYSTEM WIRING DIAGRAM Page 1 Page 2 MONITORING SYSTEM AND CONTROL SYSTEM DEVICE RELATIONSHIP CHART : Applicable Component Input Battery Ignition switch A/C switch,
Diagnostic Trouble Code (DTC) Charts
Diagnostic Trouble Code (DTC) Charts Note: Before proceeding to the Pinpoint Test, refer to the Diagnostic Trouble Code (DTC) Descriptions for additional information to assist in diagnosis. 6.0L Diesel
COVERING MILLIONS Preferred Protection Plan, a Service Group Company www.sgifs.com PO Box 26830, Austin, TX 78755-0800.
COVERING MILLIONS Preferred Protection Plan, a Service Group Company www.sgifs.com PO Box 26830, Austin, TX 78755-0800. 1-877-565-0816 PPP-308 0903 rev 0408 BENEFITS New and Pre-Owned Vehicles Preferred
INSTALLATION MANUAL. Address card EKAC10B
INSTALLATION MANUAL 88 44 µchiller compact 70 64 4a 4b G G0 power supply G G0 power supply 50 5 50 5 4a 4b 5a 5b 4 5a 5b Installation manual READ THIS MANUAL ATTENTIVELY BEFORE STARTING UP THE UNIT. DO
SERVICE MANUAL FOR 6535 SERIES TWO TON HIGH EFFICIENCY PACKAGED HEAT PUMPS
SERVICE MANUAL FOR 6535 SERIES TWO TON HIGH EFFICIENCY PACKAGED HEAT PUMPS TABLE OF CONTENTS 1. Warnings...2 2. Accessibility Of Appliance...3 3. Unit Dimensions And Specifications...3 4. Unit Specifications
LG Air Conditioning Multi F(DX) Fault Codes Sheet. Multi Split Units
Multi Split Units If there is a fault on any LG Multi unit, an Error mark is indicated on the display window of the indoor unit, wired-remote controller, and LED s of outdoor unit control board. A two
Operational Overview and Controls Guide. Two or Three Pump IronHeart Lite with Variable Frequency Drives
DOCUMENT: ECSEQ6-0 EFFECTIVE: 09/23/10 SUPERSEDES: Operational Overview and Controls Guide Two or Three Pump IronHeart Lite with Variable Frequency Drives 6700 Best Friend Road. Norcross, GA 30071. (770)
HVAC SYSTEM (AUTO A/C) (DIAGNOSTICS) AC
HVAC SYSTEM (AUTO A/C) (DIAGNOSTICS) AC Page. Basic Diagnostic Procedure.... General Description...3 3. Electrical Components Location...6 4. A/C Control Module I/O Signal...8 5. Self-diagnosis...0 6.
Oil and Coolant Circulating Heating System. Model - OCSM
Oil and Coolant Circulating Heating System Model - OCSM Installation & Operation Manual 216280-000 REV 2 Identifying Your System The HOTSTART heating system is designed to heat fluids for use in marine
Single Zone LCD Thermostat Operating Instructions
Fan Cool Furnace *Heat Pump or Heat Strip On/Off F Single Zone LCD Thermostat Operating Instructions MODEL 3313192.XXX Cool/Furnace 3313193.XXX Cool/Furnace/Heat Pump 3313194.XXX Cool/Furnace/Heat Strip
Cat Electronic Technician 2015A v1.0 Product Status Report 3/15/2015 9:34 AM
Cat Electronic Technician 2015A v1.0 Product Status Report 3/15/2015 9:34 AM Product Status Report Comments Transmission (BJW01516) Transmission Serial Number BJW01516 Torque Converter Serial Number 6AT00753
REFRIGERATED TYPE COMPRESSED AIR DRYERS INSTRUCTION MANUAL. For Sales & Service please contact:
7610.478.16 8/99 INSTRUCTION MANUAL Models 8005, 8010, 8015 For Sales & Service please contact: CENTRAIR Air Systems & Supplies Phone: 705-722-5747 Fax: 705-722-5458 Email: sales@centrair.ca Website: www.centrair.ca
Powertrain DTC (P000-P0999) for EOBD Vehicles (Directive 98/69/EC of the European Parliament)
Powertrain DTC (P000-P0999) for EOBD Vehicles (Directive 98/69/EC of the European Parliament) 1 Trouble Fault location Probable cause code 1 P0000 No fault found - P0001 Fuel volume regulator control -
GLYCOL CHILLER SYSTEM TROUBLESHOOTING 101
GLYCOL CHILLER SYSTEM TROUBLESHOOTING 101 By Jim VanderGiessen Jr, Pro Refrigeration Inc. There is a good chance your glycol chiller system is often completely forgotten about, until that dreaded day you
Heat Pump Water Heater IOM Manual
Heat Pump Water Heater IOM Manual Installation Operation & Maintenance This manual is intended as an aid to qualified service personnel for proper installation, operation and maintenance of the heat pump
CONTENTS 1. IMPORTANT NOTICE 2 2. TECHNICAL SPECIFICATION 3 3. OPERATION DETAILS 4 4. WIRING DIAGRAM 11 5. EXPLOSION VIEW 12 6.
TCL WALL MOUNTED SPLIT-TYPE AIR CONDITIONERS SERVICE MANUAL No.TE051220 Models TAC-09CHSA/GI TAC-12CHSA/GI CONTENTS 1. IMPORTANT NOTICE 2 2. TECHNICAL SPECIFICATION 3 3. OPERATION DETAILS 4 4. WIRING DIAGRAM
Lotus Service Notes Section EMP
ENGINE MANAGEMENT SECTION EMP Sub-Section Page Diagnostic Trouble Code List EMP.1 3 'Lotus Scan' Diagnostic Tool EMP.2 43 Engine Management Component Location EMP.3 45 Mechanical Throttle Setting Procedure
User manual. Atec. 086L0130 Rev. 1 EN
User manual Atec 086L0130 Rev. 1 EN Thermia Värme AB reserves the right to make changes to components and specifications without prior notice. 2010 Thermia Värme AB. The Swedish language is used for the
OPERATOR S MANUAL. Supra 550, 650, 750, 850 & 950 TRUCK REFRIGERATION UNITS
OPERATOR S MANUAL Supra 550, 650, 750, 850 & 950 TRUCK REFRIGERATION UNITS CONTENTS Page Unit Identification... 2 Safety... 3 Pre-Trip Inspection... 4 Unit Operation... 6 Starting the Unit -- Road Operation...
POLICY BULLETIN Tecumseh Compressor Company Compressor Group
to Bulk Milk Coolers and Other System Page 1 of 5 Overall reliability can be enhanced if there exists a complete understanding of the features, system design, installation requirements, processing, charging
Variable Air Volume - VAV
Mode Enable Sensor Options Variable Air Volume - VAV The temperature of this sensor will determine if the unit is in heating, cooling or vent mode during occupied operation. The following options are available:
CGC s Hybrid System Loop Control
verview The CGC Group Hybrid Heat Pump System does NT operate with the same fluid loop temperatures as a conventional reversing Water Source Heat Pump system. The CGC system differs from a WSHP system
Heating and Air Conditioning
Heating and Air Conditioning S Y L L A B U S Your Course Learning Plan UAWLETC EK 4-13-06 A. General Course Information Course description: The Heating and Air Conditioning students of UAW-LETC will successfully
Technical Information
Date of last update: Oct-11 Ref: D7.8.4/1011/E Application Engineering Europe CORESENSE DIAGNOSTICS FOR STREAM REFRIGERATION COMPRESSORS CoreSense Diagnostics for Stream Refrigeration Compressors... 1
LG Air Conditioning - Universal Split Fault Codes Sheet. Universal Split Systems
Universal Split Systems If there is a fault on any LG Universal unit, a two digit number will appear on the remote controllers led display. If the unit does not have a remote controller the fault will
NO-FROST CUSTOMER SUPPORT INFORMATION INFORMATION ON THE NO-FROST TECHNOLOGY WHITE GOODS
INFORMATION INFORMATION ON THE TECHNOLOGY The -Frost refrigerators are different from the other static refrigerators in terms of their operational system. In normal refrigerators, in the freezing section,the
Engineering Recommendation on: Accumulators Revised 6-17-99 Issued January 10, 1979 Page 1 of 7
Issued January 10, 1979 Page 1 of 7 Accumulators have long been recognized by the industry as an effective means of maintaining good system balance by storing excess refrigerant as the condenser or evaporator
SERVICE INSTRUCTION R410A. SPLIT TYPE ROOM AIR CONDITIONER Universal Floor / Ceiling Duct / Cassette Wall Mounted / Floor type INVERTER MULTI
SERVICE INSTRUCTION SPLIT TYPE ROOM AIR CONDITIONER Universal Floor / Ceiling Duct / Cassette Wall Mounted / Floor type INVERTER MULTI R410A Models Indoor unit Outdoor unit AB*14LBAJ AB*18LBAJ AB*F14LAT
Model: AC-S13CG x 2. Model No: AC-S13CGx2.doc Version 1.0
Air Conditioner Service Manual 2 3 Model: AC-S13CG x 2 3 Content Technical specification.. 4 Performance curve.5 Outline & dimension of indoor unit..10 Outline & dimension of outdoor unit 11 Exploded view
User manual. 086U6297 Rev. 9 EN
User manual Atria Atria Duo Atria Duo Optimum Atria Optimum Comfort Diplomat Diplomat Duo Diplomat Duo Optimum Diplomat Duo Optimum G2 Diplomat Optimum Diplomat Optimum G2 086U6297 Rev. 9 EN Thermia Värme
MicroTech III Unit Controller for Water Source Heat Pump Units
Operation & Maintenance Data OM 931-3 Group: WSHP Part Number: 669479403 Date: May 2012 MicroTech III Unit Controller for Water Source Heat Pump Units 2012 McQuay International 800.432.1342 www.daikinmcquay.com
26 3213.13 Diesel Engine Driven Generators Page 1 of 6
Last Update: December 8, 2014 A. Description of System Consultant s Handbook Page 1 of 6 1. Provide a diesel engine driven electric generating unit, factory assembled, tested and certified to operate at
FAULT CODE READER OBD11 FOR PETROL ENGINES PART NO
FAULT CODE READER OBD11 FOR PETROL ENGINES PART NO 77004 HANDBOOK FAULT CODE READER FOR PETROL ENGINES with OBD11 INDEX Page 1. Introduction 4 2. Instructions 5 3. Common Terms 6 4. Precautions 6 5. Fault
Data Realty Colocation Data Center Ignition Park, South Bend, IN. Owner: Data Realty Engineer: ESD Architect: BSA LifeStructures
Data Realty Colocation Data Center Ignition Park, South Bend, IN Owner: Data Realty Engineer: ESD Architect: BSA LifeStructures Project Overview Data Realty is a data center service provider for middle
ASHRAE Boston Chapter Meeting Designing AC Refrigeration Systems Lessons Learned February 11, 2014
ASHRAE Boston Chapter Meeting Designing AC Refrigeration Systems Lessons Learned February 11, 2014 Explanation of the refrigeration cycle. Compressors. Benefits and operating characteristics. -Reciprocating
*.ppt 11/2/2009 12:48 PM 1
Digital Compressor Controller *.ppt 11/2/2009 12:48 PM 1 Copeland Scroll Digital Controller Simple Controller That Enables OEM s To Use Digital Scrolls Relieves OEM From Developing Special Controllers
SECTION 412-00 Climate Control System General Information and Diagnostics
412-00-i Climate Control System General Information and Diagnostics 412-00-i SECTION 412-00 Climate Control System General Information and Diagnostics CONTENTS PAGE DIAGNOSIS AND TESTING Climate Control
NSN 4120-01-21 4-3692
*TM 9-4120-388-14 TECHNICAL MANUAL Operator s, Unit, Direct Support, And General Support Maintenance Manual AIR CONDITIONER, VERTICAL, COMPACT, 18,000 BTU/HR 208 VOLT, 3 PHASE, 50/60 HERTZ NSN 4120-01-21
Fossil fuel heating equipment
Fossil fuel heating equipment principles and troubleshooting techniques Application Note This application note was written to provide you with an understanding of the basic principles of fossil fuel heating
Hot Water. Heat pump water heaters. Residential and Commercial R410a
Hot Water Heat pump water heaters Residential and Commercial R410a Heat pump technology Heat Pump Water Heating is a new idea using existing technology and is viewed as the latest generation of water heating
Hoshizaki America, Inc.
Hoshizaki America, Inc. Stackable Crescent Cuber Models KM-1301SAH/3, SWH/3, SRH/3 KM-1400SWH-M, SWH3-M KM-1601SAH/3, SWH/3, SRH/3 KM-1900SAH/3, SWH/3, SRH/3 KM-2100SWH3, SRH3 KM-2500SWH3, SRH3 KMH-2000SWH/3,
ALL IN ONE. Heat Pump Water Heater
ALL IN ONE Heat Pump Water Heater INSTALLATION AND OPERATION INSTRUCTIONS Please read this user s manual carefully before operate the unit. www.airtradecentre.com CONTENTS A. IMPORTANT REMARKS ------------------------------------------------------------------------------------------------
Performance Evaluation of a Heat Pump System for Simultaneous Heating and Cooling
for Simultaneous Heating and Cooling F. Sustainable Energy Centre, University of South Australia Mawson Lakes Boulevard, Mawson Lakes 5095 AUSTRALIA E-mail: Frank.@UniSA.edu.au Abstract The high efficiency
13. Troubleshooting. Indoor unit s LED indication of Corona DC inverter unit. Indoor unit s LED indication of Alfa DC inverter unit
Troubleshooting 13. Troubleshooting Indoor unit s LED indication of Corona DC inverter unit MCAC-HTSM-2007-11 E0 E1 E2 E3 E5 E6 P0 P1 P2 P3 P5 EEPROM error outdoor communication error Zero-crossing examination
SECTION 23 05 93 TESTING, ADJUSTING, AND BALANCING FOR HVAC INTRODUCTORY INFORMATION
SECTION 23 05 93 TESTING, ADJUSTING, AND BALANCING FOR HVAC INTRODUCTORY INFORMATION The purpose of this guide specification is to assist the specifier in correctly specifying Mechanical System Testing
Skills Canada National Competition Instructions and Competition Details 38 Refrigeration and Air Conditioning / Post - Secondary May 27-30, 2015 -
Skills Canada National Competition Instructions and Competition Details / Post - Secondary May 27-30, 2015 - Saskatoon 1. Test Project Details This project is designed to test the range of skills used
Wynn s Extended Care
Wynn s Extended Care Every car deserves to receive the very best care... especially yours. How Do You Keep Your Reliable Transportation Reliable? Count on Wynn s Because Wynn s has been caring for cars
Service manual. Website: www.andico.com.au CAUTION - BEFORE SERVICING THE UNIT, READ THE SAFETY - PRECAUTIONS IN THIS MANUAL.
Website: www.andico.com.au Service manual CAUTION - BEFORE SERVICING THE UNIT, READ THE SAFETY - PRECAUTIONS IN THIS MANUAL. - ONLY FOR AUTHORISED SERVICE PERSONNEL. MODELS: MPK1-09CR-QB8 MPK1-12ER-QB6
Application Engineering
Application Engineering February 2011 Electronic Unit Controller Table of Contents 1. Introduction and Features... 2 1.1 Technical Specifi cations... 3 1.2 Pressure Probe Error Bypass... 3 1.3 Bump Start...