Fire Sprinkler Hanging & Bracing Products. Innovative Hanging & Bracing Fire Protection Solutions

Transcription

1 Fire Sprinkler Hanging & Bracing Products Innovative Hanging & Bracing Fire Protection Solutions

2 Innovative Products From a Trusted Leader To help ensure the availability and operation of safety systems after an earthquake event, many building and industry codes now include requirements for the design and installation of seismic sway bracing for non-structural components, such as fire sprinkler, mechanical, electrical and plumbing systems. The innovative line of CADDY Bracing Systems was developed to help keep fire sprinkler systems intact after a seismic event and to minimize water damage resulting from leaks or ruptures. CADDY Bracing Systems provide contractors with high-quality, engineered solutions, which include rigid bracing, cable bracing and rod stiffeners. : Quick and easy installation Meets NFPA 13 Lower total installed cost culus Listed OSHPD Pre-Approved FM Approved 2

3 CADDY Bracing System Software Now it s easier than ever to select the correct CADDY bracing products for use in fire protection applications. ERICO has unveiled the CADDY Bracing Systems Calculator, a new web-based calculator which allows users to create and save designs for multiple projects while providing the necessary submittal forms. This timesaving calculator simplifies the selection of products and provides the necessary engineering calculations providing a complete solution to support rigid bracing, cable bracing and branch line restraints. No installation needed access via a current web browser Offers dynamic design preview and uses visual design tools Generates a complete submittal and project materials list Create, manage, and re-use designs Supports NFPA 13 including 2013 ed., IBC and other building codes 3

4 Pipe Hangers 115 Standard Duty Loop Hanger Page 15 Surge Restraint Page 16 Yook Hanger Page Stainless Steel Loop Hanger Page Galvanized Clevis Hanger Page Light Duty Clevis Hanger Page CADDY EZ RISER for Close Quarters Page CADDY EZ RISER Page Malleable Split Ring Hanger Page Malleable Split Ring Hanger for Copper Tube Page

5 CPVC Hanging System 107 Wraparound Strap for CPVC Pipe Page Hole Strap for CPVC Pipe Page Side Mount Strap for CPVC Pipe Page 29 SOSR Stand Off 2-Hole Strap for CPVC Pipe Page 30 CADDY MACROFIX PLUS NI with Easy Closure Page 31 3TW Fastener for SOSR Series Page 32 Easy Snap Grommet for Factory Punched Holes Page 32 Snap-On Nail Plate Page 33 Pipe Supports 721 Pipe Support with U-Bolt Page Adjustable Pipe Support Page Adjustable Pipe Support Assembly Page Adjustable Pipe Support Assembly with U-Bolt Page

6 CADDY ROD LOCK CADDY ROD LOCK Beam Clamp Page 39 CADDY ROD LOCK Anchor Screw Page 40 SN Series Nut Page 41 Structural Attachments 300 Universal Beam Clamp Page Universal Beam Clamp, Wide Mouth Page Stainless Steel Top-Mount Beam Clamp Page C Standard Retainer Strap Page 47 34SL Retrofit Retainer Strap Page 48 PH Multi-Purpose Purlin Clamp Page 49 PHSW Multi-Purpose Purlin Clamp with Swivel Page Malleable Iron Purlin Clamp Page

7 Structural Attachments 547/548 C-Clamp Page Steel Side Beam Attachment Page Malleable Iron Side Beam Attachment Page Universal Steel Side Beam Attachment Page Side Beam Attachment Page Threaded Steel Side Beam Attachment Page Steel Eye Socket Rod Hanger Page Offset Steel Eye Socket Rod Hanger Page Steel Wall or Ceiling Plate Page M Malleable Iron Wall or Ceiling Plate Page Standard Duty Welded Wall Bracket Page Heavy Duty Welded Wall Bracket Page A Single Concrete Insert Plate and Rod Page Concrete Insert Plate Page N Nut for 355 Series Page

8 Rigid Bracing System Bar Joist Attachment Page Adjustable I-Beam Attachment Page 70 I-Beam Attachment Page 71 Multi Attachment Page 72 Universal Structural Attachment Page 73 Easy Universal Sway Brace Page Standard Universal Sway Brace Page Quick Grip Jr. Lateral Sway Brace Page Quick Grip Lateral Sway Brace Page Shear Bolt Page 82 Shear Nut Page

9 Cable Bracing System Cable Spool Page 86 Crimping Sleeve Page 86 Stake Eye Kit Page 87 Loop Attachment Clip Page 88 No Pry Clip Page 88 Universal Restraint Clip Page 89 Universal Restraint Clip, Retrofit Page 90 Cable Cutter Page 91 Manual Swaging Tool Page 91 Multi-Size Manual Swaging Tool Page 92 Battery Powered Swaging Tool Page 92 Die Set for Battery Powered Swaging Tool Page

10 Branch Line Restraint System Branch Line Restraint Pipe Attachment Page 94 Branch Line Restraint Structure Attachment to Steel Page 95 Branch Line Restraint Structure Attachment to Wood/Concrete Page 96 Branch Line Restraint Structure Attachment to Threaded Hole Page 97 Bracing Accessories Strut Seismic Hinge Page 99 Pipe Rod Stiffener Page 100 Strut Rod Stiffener Page

11 Hardware Threaded Rod Page M Standard U-Bolt Page EM-HEX Rod Coupler Page R Hex Rod Reducer Page Hex Head Lag Screw Page Wood Drive Screw Page Tie Bolt Page

12 Anchors Drop-In Anchor Page 112 Flanged Drop-in Anchor Page 112 Spike Anchor Page 113 Wedge Expansion Anchor Bolt Page 114 Concrete Anchor Screw Page 115 Screw Drill Bits Page 115 HangerMate Vertical Mount Screw for Steel Page 116 HangerMate Vertical Mount Screw for Steel with Lock Nut Page 116 HangerMate Horizontal Mount Screw for Steel Page 117 HangerMate Horizontal Mount Screw for Steel with Lock Nut Page 117 HangerMate Vertical Mount Screw for Wood Page 118 HangerMate Horizontal Mount Screw for Wood Page

13 Anchors HangerMate Vertical Mount Screw for Concrete Page 119 HangerMate SDS Drill Bit for Hammer Drills Page 119 HangerMate Drill Bit Adaptor Page 120 HangerMate Tanged Drill Bit for Hammer Drills Page 120 HangerMate Hex Drive Socket Page 121 HangerMate Drive Sleeve Page

14 Pipe Hangers 115 Standard Duty Loop Hanger Page 15 Surge Restraint Page 16 Yook Hanger Page Stainless Steel Loop Hanger Page Galvanized Clevis Hanger Page Light Duty Clevis Hanger Page CADDY EZ RISER for Close Quarters Page CADDY EZ RISER Page Malleable Split Ring Hanger Page Malleable Split Ring Hanger for Copper Tube Page

15 115 Standard Duty Loop Hanger Pipe Hangers The 115 Standard Duty Loop Hanger, part of the CADDY line of fasteners and supports from ERICO, is ideal for suspending stationary, non-insulated pipe lines, including CPVC pipes, in fire sprinkler systems. A knurled insert nut helps simplify vertical adjustments and flared edges on the base (1/2 to 2 sizes) help protect pipes from coming into contact with any sharp edges of the hanger. Flared edges help prevent any sharp surfaces from coming into contact with the pipe (1/2 to 2 sizes) Retained insert nut helps ensure the loop hanger and insert nut stay together Recommended for the suspension of stationary non-insulated pipe lines Manufactured to use the minimum rod size permitted by NFPA for fire sprinkler piping Conforms with Federal Specification WW-H-171 (Type 10), Manufacturers Standardization Society (MSS) SP-58 and SP-69 (Type 10) Finish: Pre-galvanized Pipe Size Outer Diameter OD Rod Size RS A B C Static Load F EG 1/ /8 2 13/16 1 1/ lb EG 3/ / /16 15/ lb EG /8 3 1/4 1 3/8 15/ lb EG 1 1/ /8 3 9/16 1 1/2 15/ lb EG 1 1/ /8 3 13/16 1 5/8 15/ lb EG 2 2 3/8 3/8 4 1/4 1 7/8 15/ lb EG 2 1/2 2 7/8 3/8 5 9/ /16 1 9/ lb EG 3 3 1/2 3/8 6 9/16 3 1/2 1 15/ lb EG 3 1/2 4 3/8 7 1/16 3 3/4 1 15/ lb EG 4 4 1/2 3/8 7 9/ / lb EG 5 5 9/16 1/2 9 13/16 4 3/4 2 1/4 1,000 lb EG 6 6 5/8 1/2 11 5/16 6 5/16 3 5/16 1,000 lb EG 8 8 5/8 1/2 12 7/8 6 7/8 2 7/8 1,000 lb 15

16 Surge Restraint Pipe Hangers Surge restraint for 115 standard duty loop hangers Finish: CADDY ARMOUR Pipe Size SR6 1/2 2 Yook Hangers Use in place of U-hook Use with Model #43, size #16 x 2 L Wood Drive Screws Finish: Pre-galvanized Pipe Size Height H Width W Static Load F EG 1 1 1/4 6 7/8 2 13/ lb EG 1 1/ /8 3 1/2 250 lb EG 2 1/ /8 4 13/ lb EG 3 1/ /8 5 15/ lb For 2-1/2 thru 4 pipe sizes, use two drive screws per leg. 16

17 105 Stainless Steel Loop Hanger Pipe Hangers Recommended for the suspension of stationary stainless steel pipe lines Conforms with Federal Specification WW-H-171 (Type 10), Manufacturers Standardization Society (MSS) SP-58 and SP-69 (Type 10) Pipe Size Outer Diameter OD Rod Size RS Material: Stainless steel 304 A B C Static Load F S4 1/ /8 2 7/8 2 5/16 1 7/8 610 lb S4 3/ /8 3 1/8 2 3/8 1 7/8 610 lb S /8 3 3/8 2 9/16 1 7/8 610 lb S4 1 1/ /8 3 3/4 2 11/16 1 7/8 610 lb S4 1 1/ /8 4 1/ / lb S /8 3/8 4 7/16 3 1/16 1 7/8 610 lb S4 2 1/2 2 7/8 1/2 4 15/16 3 5/16 1 7/8 970 lb S /2 1/2 5 9/16 3 5/8 1 7/8 970 lb S4 3 1/2 4 1/2 6 1/16 3 7/8 1 7/8 970 lb S /2 5/8 6 9/16 4 1/8 1 7/8 1,250 lb S /16 5/8 7 5/8 4 11/16 1 7/8 1,250 lb S /8 3/4 8 3/4 5 1/16 1 3/4 1,600 lb S /8 3/4 10 3/4 6 1/16 1 3/4 1,800 lb Material: Stainless steel S /8 3/8 4 7/16 3 1/16 1 7/8 610 lb S /2 1/2 5 9/16 3 5/8 1 7/8 970 lb S /2 5/8 6 9/16 4 1/8 1 7/8 1,250 lb S /8 3/4 8 3/4 5 1/16 1 3/4 1,600 lb 17

18 401 Galvanized Clevis Hanger Pipe Hangers Recommended for the suspension of stationary non-insulated pipe lines Conforms with U.S. Federal Specification WW-H-171 (Type 1), Manufacturers Standardization Society (MSS) SP-58 and SP-69 (Type 1) Pipe Size Outer Diameter OD Rod Size RS A B C Static Load F Listings Approvals Finish: Electro-galvanized EG 1/ /8 2 1/8 1 1/16 1/4 610 lb cul, UL EG 3/ /8 2 3/8 1 3/16 3/8 610 lb cul, UL EG /8 2 13/16 1 1/2 9/ lb cul, UL EG 1 1/ /8 3 5/ /16 11/ lb cul, UL EG 1 1/ / /8 1 1/ lb cul, UL EG 2 2 3/8 3/8 4 1/2 2 5/8 1 1/8 610 lb cul, UL EG 2 1/2 2 7/8 1/2 5 1/ /16 1,130 lb cul, UL, FM EG 3 3 1/2 1/ /16 7/8 1,130 lb cul, UL, FM EG 3 1/2 4 1/2 6 1/2 3 11/16 1 3/8 1,130 lb cul, UL, FM EG 4 4 1/2 5/8 7 3/4 4 5/8 1 3/4 1,130 lb cul, UL, FM 18

19 401 Galvanized Clevis Hanger Pipe Size Outer Diameter OD Rod Size RS Finish: Electro-galvanized A B C Static Load F Listings Approvals EG 5 5 9/16 5/8 9 3/4 5 5/8 2 3/16 1,430 lb cul, UL, FM EG 6 6 5/8 3/4 11 3/4 7 1/ /16 1,940 lb cul, UL, FM EG 8 8 5/8 3/ /8 2,000 lb cul, UL, FM EG /4 7/8 16 1/2 9 1/16 2 9/16 3,600 lb EG /4 7/8 18 5/8 10 3/16 3 1/16 3,800 lb EG /4 12 1/8 4 3/8 4,200 lb EG /2 4 5/8 4,600 lb EG /8 26 3/ /8 4,800 lb EG / ,800 lb EG /4 34 1/8 18 5/8 5 11/16 4,800 lb - Finish: Hot-dip galvanized HD 1/ /8 2 1/8 15/16 1/4 610 lb cul, UL HD 3/ /8 2 3/8 1 1/16 3/8 610 lb cul, UL HD /8 2 13/16 1 3/8 9/ lb cul, UL HD 1 1/ /8 3 5/16 1 3/4 11/ lb cul, UL HD 1 1/ / /4 1 1/ lb cul, UL HD 2 2 3/8 3/8 4 1/2 2 9/16 1 1/8 610 lb cul, UL HD 2 1/2 2 7/8 1/2 5 1/4 2 13/16 1 1/16 1,130 lb cul, UL, FM HD 3 3 1/2 1/ /4 7/8 1,130 lb cul, UL, FM HD 4 4 1/2 5/8 7 3/4 4 1/4 1 3/4 1,130 lb cul, UL, FM HD 5 5 9/16 5/8 9 3/4 5 11/16 2 3/16 1,430 lb cul, UL, FM HD 6 6 5/8 3/4 11 3/4 6 7/8 2 11/16 1,940 lb cul, UL, FM HD 8 8 5/8 3/ /8 3 1/8 2,000 lb cul, UL, FM HD /4 7/8 16 1/2 9 1/16 2 9/16 3,600 lb HD /4 7/8 18 5/8 10 3/16 3 1/16 3,800 lb - Pipe Hangers 19

20 410 Light Duty Clevis Hanger Pipe Hangers Recommended for the suspension of stationary non-insulated pipe lines Conforms with U.S. Federal Specification WW-H-171 (Type 1), Manufacturers Standardization Society (MSS) SP-58 and SP-69 (Type 1) Finish: Electro-galvanized Pipe Size Outer Diameter OD Rod Size RS A B C Static Load F EG 1/ /8 2 1/8 1 1/16 1/4 150 lb EG 3/ /8 2 3/8 1 3/16 3/8 150 lb EG /8 2 3/4 1 1/2 9/ lb EG 1 1/ /8 3 5/ /16 11/ lb EG 1 1/ / /8 1 1/ lb EG 2 2 3/8 3/8 4 1/2 2 5/8 1 1/8 250 lb EG 2 1/2 2 7/8 1/2 5 1/ / lb EG 3 3 1/2 1/ /16 7/8 350 lb EG 3 1/2 4 1/2 6 1/2 3 11/16 1 3/8 400 lb EG 4 4 1/2 5/8 7 3/4 4 5/8 1 3/4 500 lb EG 5 5 9/16 5/8 9 3/4 5 5/8 2 3/ lb EG 6 6 5/8 3/4 11 3/4 7 1/ / lb EG 8 8 5/8 3/ /8 1,200 lb 20

21 512 CADDY EZ RISER for Close Quarters Pipe Hangers Innovative design eliminates loose hardware, simplifying installation Serrated flange-head bolts eliminate need for wrenches on both bolt and nut Short ears allow for use in spaces where full-sized risers do not fit Conforms with Federal Specification WW-H-171 (Type 8), Manufacturers Standardization Society (MSS) SP-58 and SP-69 (Type 8) Finish: Electro-galvanized Pipe Size Outer Diameter OD Hole Size HS A B Static Load F EG / lb EG 1 1/ /16 5 5/ lb EG 1 1/ /16 6 1/ lb EG 2 2 3/8 7/16 6 5/8 1 3/ lb EG 2 1/2 2 7/8 7/16 7 5/8 1 3/ lb EG 3 3 1/2 9/16 8 5/8 1 3/ lb EG 4 4 1/2 9/ /4 1 1/2 810 lb EG 5 5 9/16 9/ /16 1 1/2 1,160 lb EG 6 6 5/8 9/ /16 2 1,570 lb 21

22 510 CADDY EZ RISER Pipe Hangers Recommended for suspending vertical steel pipe risers Slotted holes make assembly easy, eliminating loose hardware Serrated flange-head bolts eliminate need for wrenches on both bolt and nut Conforms with Federal Specification WW-H-171 (Type 8), Manufacturers Standardization Society (MSS) SP-58 and SP-69 (Type 8) Pipe Size Outer Diameter OD Hole Size HS A B Static Load F Listings Finish: Electro-galvanized EG 1/ /16 8 1/ lb EG 3/ / lb EG / lb EG 1 1/ /16 9 7/ lb EG 1 1/ /16 9 7/ lb EG 2 2 3/8 7/ /4 1 3/ lb cul, UL EG 2 1/2 2 7/8 7/ / lb cul, UL EG 3 3 1/2 7/ /4 1 3/ lb cul, UL EG 3 1/2 4 9/ /8 1 3/ lb cul, UL EG 4 4 1/2 9/ /2 810 lb cul, UL EG 5 5 9/16 9/ /2 1 1/2 1,160 lb cul, UL EG 6 6 5/8 9/ ,570 lb cul, UL EG 8 8 5/8 11/ /4 2 2,500 lb cul, UL 22

23 510 CADDY EZ RISER Pipe Size Outer Diameter OD Hole Size HS A B Static Load F EG /4 11/ /8 2 2,500 lb EG /4 11/ /8 2 2,700 lb EG / /8 2 2,700 lb EG / /8 2 1/2 2,900 lb EG / /16 2 1/2 2,900 lb EG / /4 2 1/2 2,900 lb EG / /8 3 2,900 lb - Finish: Hot-dip galvanized HD 1/ /16 8 1/ lb HD / lb HD 1 1/ /16 9 7/ lb HD 1 1/ /16 9 7/ lb - Listings HD 2 2 3/8 7/ /4 1 3/ lb cul, UL HD 2 1/2 2 7/8 7/ / lb cul, UL HD 3 3 1/2 7/ /4 1 3/ lb cul, UL HD 4 4 1/2 9/ /2 810 lb cul, UL HD 5 5 9/16 9/ /2 1 1/2 1,160 lb cul, UL HD 6 6 5/8 9/ ,570 lb cul, UL HD 8 8 5/8 11/ /4 2 2,500 lb cul, UL Material: Stainless steel S4 1/ /16 8 1/ lb S4 3/ / lb S / lb S4 1 1/ /16 9 7/ lb S4 1 1/ /16 9 7/ lb S /8 7/ /4 1 3/ lb cul, UL S4 2 1/2 2 7/8 7/ / lb cul, UL S /2 7/ /4 1 3/ lb cul, UL S /2 9/ /2 810 lb cul, UL S /16 9/ /2 1 1/2 1,160 lb cul, UL S /8 9/ ,570 lb cul, UL S /8 11/ /4 2 2,500 lb cul, UL S /4 11/ /8 2 2,500 lb - Pipe Hangers Clamp is fitted for steel pipe and should be installed below a coupling or shear lug, with bolts torqued to recommended value. Slotted holes and bolts for pipe sizes up to 12 only. 23

24 455 Malleable Split Ring Hanger Pipe Hangers Recommended for the suspension of stationary non-insulated pipe lines Allows for piping runs close to ceiling or walls Conforms with Federal Specification WW-H-171 (Type 25), Manufacturers Standardization Society (MSS) SP-58 and SP-69 (Type 12) Material: Cast iron Pipe Size Outer Diameter OD Rod Size RS A B Static Load F Finish: Electro-galvanized EG 3/ /8 1 5/16 3/8 180 lb EG 1/ /8 1 1/2 3/8 180 lb EG 3/ /8 1 3/4 7/ lb EG /8 2 7/ lb EG 1 1/ /8 2 3/8 1/2 180 lb EG 1 1/ /8 2 5/8 1/2 180 lb EG 2 2 3/8 3/8 3 1/8 1/2 180 lb EG 2 1/2 2 7/8 1/2 3 1/4 5/8 300 lb EG 3 3 1/2 1/2 4 3/8 5/8 300 lb EG 4 4 1/2 1/2 5 3/8 11/ lb Finish: Plain PL 3/ /8 1 5/16 3/8 180 lb PL 1/ /8 1 1/2 3/8 180 lb PL 3/ /8 1 3/4 7/ lb PL /8 2 7/ lb PL 1 1/ /8 2 3/8 1/2 180 lb PL 1 1/ /8 2 5/8 1/2 180 lb PL 2 2 3/8 3/8 3 1/8 1/2 180 lb PL 2 1/2 2 7/8 1/2 3 1/4 5/8 300 lb PL 3 3 1/2 1/2 4 3/8 5/8 300 lb PL 4 4 1/2 1/2 5 3/8 11/ lb Bolt and rivet are carbon steel. 24

25 456 Malleable Split Ring Hanger for Copper Tube Pipe Hangers Recommended for the suspension of stationary non-insulated copper tube lines Allows for piping runs close to ceiling or walls Conforms with Federal Specification WW-H-171 (Type 25), Manufacturers Standardization Society (MSS) SP-58 and SP-69 (Type 12) Material: Cast iron Finish: Electro-galvanized Color: Brown Pipe Size Outer Diameter OD Rod Size RS A B Static Load F CP 3/ /8 15/16 5/ lb CP 1/ /8 1 1/8 3/8 180 lb CP 3/ /8 1 3/8 3/8 180 lb CP /8 1 5/8 3/8 180 lb CP 1 1/ /8 1 7/8 3/8 180 lb CP 1 1/ /8 2 1/8 3/8 180 lb CP 2 2 3/8 3/8 2 5/8 3/8 180 lb CP 2 1/2 2 7/8 1/2 3 3/8 5/8 180 lb CP 3 3 1/2 1/2 3 7/8 5/8 180 lb CP 4 4 1/2 1/2 5 5/8 180 lb Bolt and rivet are carbon steel. 25

26 CPVC Hanging System 107 Wraparound Strap for CPVC Pipe Page Hole Strap for CPVC Pipe Page Side Mount Strap for CPVC Pipe Page 29 SOSR Stand Off 2-Hole Strap for CPVC Pipe Page 30 CADDY MACROFIX PLUS NI with Easy Closure Page 31 3TW Fastener for SOSR Series Page 32 Easy Snap Grommet for Factory Punched Holes Page 32 Snap-On Nail Plate Page

27 107 Wraparound Strap for CPVC Pipe Includes flared edges to protect piping Rated for use with CPVC fire sprinkler pipe CPVC Hanger System Finish: Pre-galvanized Pipe Size Outer Diameter OD Hole Size HS A B C Hanger Spacing EG 3/ /32 1 1/4 2 3/8 1 3/16 6 Max EG /32 1 7/ /16 1 3/16 6 Max EG 1 1/ /32 1 5/8 3 1/16 1 3/16 7 Max EG 1 1/ /32 1 3/4 3 5/16 1 3/16 7 Max EG 2 2 3/8 7/32 1 7/8 3 11/16 1 3/16 8 Max 27

28 108 2-Hole Strap for CPVC Pipe CPVC Hanger System Includes flared edges to protect piping Rated for use with CPVC fire sprinkler pipe Finish: Pre-galvanized Pipe Size Outer Diameter OD Hole Size HS A B C Hanger Spacing EG 3/ /32 3 1/4 2 1/4 1 3/16 6 Max EG /32 3 1/2 2 1/2 1 3/16 6 Max EG 1 1/ /32 4 1/4 3 1/4 1 3/16 7 Max EG 1 1/ /32 4 7/16 3 7/16 1 3/16 7 Max EG 2 2 3/8 7/ / /16 1 3/16 8 Max 28

29 109 Side Mount Strap for CPVC Pipe Includes flared edges to protect piping Rated for use with CPVC fire sprinkler pipe CPVC Hanger System Finish: Pre-galvanized Pipe Size Outer Diameter OD Hole Size HS A B C Hanger Spacing EG 3/ /32 2 5/ /16 1 3/16 6 Max EG /32 2 5/8 1 15/16 1 3/16 6 Max EG 1 1/ / /16 2 5/16 1 3/16 7 Max EG 1 1/ /32 3 3/16 2 1/2 1 3/16 7 Max EG 2 2 3/8 7/32 3 5/ /16 8 Max 29

30 SOSR Stand Off 2-Hole Strap for CPVC Pipe CPVC Hanger System Includes flared edges to protect piping Rated for use with CPVC fire sprinkler pipe Finish: Pre-galvanized Pipe Size Hole Size HS A B C Hanger Spacing Standard Packaging Quantity Listings SOSR075 3/ /16 3 5/8 1 6 Max 100 pc cul, UL SOSR075B10 3/ /16 3 5/8 1 6 Max 10 x 10 pc - SOSR / / Max 100 pc cul, UL SOSR100B / / Max 10 x 10 pc - SOSR / /16 3 5/8 1 6 Max 100 pc cul, UL SOSR125B10 1 1/ /16 3 5/8 1 6 Max 10 x 10 pc - SOSR / /8 4 1/2 1 7 Max 100 pc cul, UL SOSR150B10 1 1/ /8 4 1/2 1 7 Max 10 x 10 pc - SOSR /4 1 8 Max 100 pc cul, UL SOSR200B /4 1 8 Max 10 x 10 pc

31 CADDY MACROFIX PLUS NI with Easy Closure Contains easy closing mechanism Plastic washers help prevent crushing the CPVC or plastic pipe and assure a floating fit Flared edges and specially designed welding area help protect CPVC piping CPVC Hanger System Nut Included: Yes Finish: Electro-galvanized Pipe Size Outer Diameter OD Rod Size RS Width W Thickness T Static Load F Listings Approvals EG 1/ /8 1 3/16 1/ lb cul, UL EG 3/ /8 1 3/16 1/ lb cul, UL, FM EG /8 1 3/16 1/ lb cul, UL, FM EG 1 1/ /8 1 3/16 1/ lb cul, UL, FM EG 1 1/ /8 1 3/16 5/ lb cul, UL, FM EG /8 1 3/16 5/ lb cul, UL, FM EG 2 1/2 2 7/ /8 1 3/16 5/ lb cul, UL EG 3 3 1/ /8 1 3/16 5/ lb cul, UL EG 3 1/ /8 1 3/16 3/ lb EG /2 3/8 1 3/16 3/ lb cul, UL EG 5 5 1/ /8 1 3/16 3/ lb

32 3TW Fastener for SOSR Series CPVC Hanger System Backing nut for use with SOSR on composite wood joist installations Finish: CADDY ARMOUR Screw Diameter Sc Height H Length L Width W 3TW #10 7/16 1 1/2 1 1/4 Easy Snap Grommet for Factory Punched Holes Snap grommet into a factory punched hole of any shape Provides anti-rattle protection Provides 360 protection of conduit, plumbing and fire sprinkler plumbing in metal studs Material: Polyethylene Copper Tube Size EMT Conduit Size Rigid Conduit/Pipe Size ESGFP 1 Max 1/2, 3/4, 1 1/2, 3/4,

33 Snap-On Nail Plate Protects electrical and mechanical installation through studs For wood and metal studs Press-on installation No tools required Breakable tabs permit multiple plates to be ganged together Holes on legs and surface of plate are provided to secure with nail or screw CPVC Hanger System Finish: CADDY ARMOUR Hole Size HS 304B2 3/16 1 3/8 3 1/8 A B 33

34 Pipe Supports 721 Pipe Support with U-Bolt Page Adjustable Pipe Support Page Adjustable Pipe Support Assembly Page Adjustable Pipe Support Assembly with U-Bolt Page

35 721 Pipe Support with U-Bolt Stanchion type support where vertical adjustment is not needed U-bolt provides additional stability Pipe Supports Finish: Plain Pipe Size A B C PL 2 1/2 3 5/ PL 3 3 7/ PL 4 4 3/ PL / PL 6 5 7/ PL / PL / PL / PL / PL / PL / PL / Install in accordance with applicable code. 35

36 722 Adjustable Pipe Support NPT pipe welded to pipe saddle with a NPT pipe lock nut allowing for vertical adjustment in the pipe stanchion Conforms with Federal Specification WW-H-171 (Type 39), Manufacturers Standardization Society ANSI /MSS-SP-58 (Type 38) Finish: Plain Pipe Size G Angle A PL 4 1 1/ / PL 6 1 1/ / PL 8 1 1/ / PL / /4 Install in accordance with applicable code. Pipe Supports 723 Adjustable Pipe Support Assembly Supports horizontal pipe from stanchions where vertical adjustment is needed Conforms with Federal Specification WW-H-171 (Type 38, 39), Manufacturers Standardization Society ANSI /MSS-SP-58 (Type 38) Finish: Plain Pipe Size Rod Size RS A B PL 2 1/2 1 1/2 2 11/ / / PL 3 1 1/2 2 7/8 8 1/8 12 5/ PL 4 2 1/2 3 3/4 9 7/ / PL 6 2 1/2 4 3/4 10 7/ / PL 8 2 1/2 6 11/ /8 16 7/8 Gussets furnished on 8 and larger. Install in accordance with applicable code. 36

37 724 Adjustable Pipe Support Assembly with U-Bolt Supports horizontal pipe from stanchions where vertical adjustment is needed Conforms with Federal Specification WW-H-171 (Type 38, 39), Manufacturers Standardization Society ANSI /MSS-SP-58 (Type 37, 38) Finish: Plain Pipe Size Rod Size RS A B PL 2 1/2 1 1/2 3 1/8 8 3/8 12 7/ PL 3 1 1/2 3 7/ / / PL 4 2 1/2 4 1/4 9 15/ / PL 6 2 1/2 5 1/2 11 3/ / PL 8 2 1/ / / PL / / / PL /2 9 3/ /8 19 3/8 Gussets furnished on 8 and larger. Install in accordance with applicable code. Pipe Supports 37

38 CADDY ROD LOCK CADDY ROD LOCK Beam Clamp Page 39 CADDY ROD LOCK Anchor Screw Page 40 SN Series Nut Page

39 CADDY ROD LOCK Beam Clamp Easy push-to-install design allows installers to simply push the threaded rod through the mounting hole, instantly locking it into position Works with slightly damaged threads and minor burrs on the threaded rod Reduces installation time up to 60% Material: Cast iron Finish: Electro-galvanized Rod Size RS Flange Thickness FT Height H For use on plain and electro zinc plated hardware only. Recognizing that torque wrenches are generally not used or available on many job sites, the setscrew should be tightened so it contacts the I-beam and then an additional 1/2 turn added. Length L Width W A Static Load F CRLB37EG 3/8 1/8 7/16 1 3/ lb CADDY ROD LOCK 39

40 CADDY ROD LOCK Anchor Screw For use with concrete and solid brick Works with slightly damaged threads and minor burrs on the threaded rod Reduces installation time up to 35% Finish: Electro-galvanized Rod Size RS A B C Drill Bit Size Drill Hole Depth Static Load F CRLA37EG 3/8 2 7/8 1 1/4 7/8 5/ lb CADDY ROD LOCK For use on plain and electro zinc plated hardware only. Tested in 3000 psi (20.67 Mpa) concrete. 40

41 SN Series Nut Allows side mounting of nut to threaded rod Reduces the need for threading compared to standard nuts and washers Ideal for retrofit projects, such as trapeze installations Works with slightly damaged threads and minor burrs on the threaded rod Reduces installation time up to 50% Finish: Electro-galvanized For use on plain and electro zinc plated hardware only. Rod Size RS A B Static Load F SN25 1/4 3/4 7/8 500 lb SN37 3/8 3/4 7/8 1,350 lb SN50 1/2 3/4 7/8 2,250 lb CADDY ROD LOCK 41

42 Structural Attachments 300 Universal Beam Clamp Page Universal Beam Clamp, Wide Mouth Page Stainless Steel Top-Mount Beam Clamp Page C Standard Retainer Strap Page 47 34SL Retrofit Retainer Strap Page 48 PH Multi-Purpose Purlin Clamp Page 49 PHSW Multi-Purpose Purlin Clamp with Swivel Page Malleable Iron Purlin Clamp Page

43 547/548 C-Clamp Page Steel Side Beam Attachment Page Malleable Iron Side Beam Attachment Page Universal Steel Side Beam Attachment Page Side Beam Attachment Page Threaded Steel Side Beam Attachment Page Steel Eye Socket Rod Hanger Page Offset Steel Eye Socket Rod Hanger Page Steel Wall or Ceiling Plate Page M Malleable Iron Wall or Ceiling Plate Page Standard Duty Welded Wall Bracket Page Heavy Duty Welded Wall Bracket Page A Single Concrete Insert Plate and Rod Page Concrete Insert Plate Page N Nut for 355 Series Page

44 300 Universal Beam Clamp Conforms with Federal Specification WW-H-171 (Type 23), Manufacturers Standardization Society ANSI /MSS-SP-58 (Type 19 and 23), install in accordance with ANSI/MSS-SP-69 Rod Size RS Flange Thickness FT A Screw Diameter Sc Torque TQ Static Load 1 F1 Static Load 2 F2 Standard Packaging Quantity Listings Approvals Finish: Electro-galvanized EG 3/8 13/16 Max 1 1/8 3/8 5 ft lb 500 lb 250 lb 100 pc cul, UL, FM EG 1/2 13/16 Max 1 1/8 7/16 8 ft lb 950 lb 760 lb 50 pc cul, UL, FM EG 5/8 13/16 Max 1 1/8 3/8 5 ft lb 950 lb 760 lb 50 pc cul, UL EG 3/4 13/16 Max 1 1/8 3/8 5 ft lb 950 lb 760 lb 50 pc cul, UL EG 7/8 13/16 Max 1 1/8 3/8 5 ft lb 950 lb 760 lb 50 pc cul, UL Finish: Plain PL 3/8 13/16 Max 1 1/8 3/8 5 ft lb 500 lb 250 lb 100 pc cul, UL, FM PL 1/2 13/16 Max 1 1/8 7/16 8 ft lb 950 lb 760 lb 50 pc cul, UL, FM PL 5/8 13/16 Max 1 1/8 3/8 5 ft lb 950 lb 760 lb 50 pc cul, UL Structural Attachments PL 3/4 13/16 Max 1 1/8 3/8 5 ft lb 950 lb 760 lb 50 pc cul, UL PL 7/8 13/16 Max 1 1/8 3/8 5 ft lb 950 lb 760 lb 50 pc cul, UL Setscrew must be tightened and torqued onto the sloped side of the I-beam. Recognizing that torque wrenches are generally not used or available on many job sites, the setscrew should be tightened so it contacts the I-beam and then an additional 1/4 to 1/2 turn added. 44

45 310 Universal Beam Clamp, Wide Mouth Universal beam clamp for thick beams Conforms with Federal Specification WW-H-171 (Type 23), Manufacturers Standardization Society ANSI /MSS-SP-58 (Type 19 and 23), install in accordance with ANSI/MSS-SP-69 Rod Size RS Flange Thickness FT A Screw Diameter Sc Torque TQ Static Load 1 F1 Static Load 2 F2 Finish: Electro-galvanized EG 3/8 1 1/4 Max 1 3/8 5 ft lb 500 lb 250 lb EG 1/2 1 1/4 Max 1 1/2 11 ft lb 950 lb 760 lb Finish: Plain PL 3/8 1 1/4 Max 1 3/8 5 ft lb 500 lb 250 lb PL 1/2 1 1/4 Max 1 1/2 11 ft lb 950 lb 760 lb Setscrew must be tightened and torqued onto the sloped side of the I-beam. Recognizing that torque wrenches are generally not used or available on many job sites, the setscrew should be tightened so it contacts the I-beam and then an additional 1/4 to 1/2 turn added. Structural Attachments 45

46 305 Stainless Steel Top-Mount Beam Clamp Pressed steel beam clamp Conforms with Federal Specification WW-H-171 (Type 23), Manufacturers Standardization Society ANSI /MSS-SP-58 (Type 19 and 23), install in accordance with ANSI/MSS-SP-69 Structural attachment to top flange of metal beams, purlins, channel, or angle iron Material: Stainless steel 304 Rod Size RS Flange Thickness FT A Screw Diameter Sc Screw Length L Torque TQ Static Load F S4 3/8 5/8 Max 7/8 3/8 1 1/2 5 ft lb 500 lb S4 1/2 5/8 Max 7/8 3/8 1 1/2 5 ft lb 1,130 lb Set screw must be tightened and torqued onto the sloped side of the I-beam, channel, or angle iron flange. Recognizing that torque wrenches are generally not used or available on many job sites, the setscrew should be tightened so it contacts the I-beam and then an additional 1/4 to 1/2 turn added. Structural Attachments 46

47 300C Standard Retainer Strap RS W L Retainer strap for beam clamps Finish: Electro-galvanized Rod Size Length Width 300C3706EG 3/8 6 15/16 300C3708EG 3/8 8 15/16 300C3710EG 3/ /16 300C3712EG 3/ /16 300C3714EG 3/ /16 300C3716EG 3/ /16 300C3718EG 3/ /16 300C5008EG 1/2 8 15/16 300C5010EG 1/ /16 300C5012EG 1/ /16 300C5014EG 1/ /16 300C5016EG 1/ /16 300C6206EG 5/ /16 300C6208EG 5/ /16 300C6210EG 5/ /16 300C6212EG 5/ /16 300C6214EG 5/ /16 300C7506EG 3/ /16 300C7508EG 3/ /16 300C7510EG 3/ /16 300C7514EG 3/ /16 300C8706EG 7/ C8708EG 7/ C8714EG 7/ Field bend and use jam nut over hanger rod to secure. Add 2 to width of flange to determine minimum length strap required. Structural Attachments 47

48 34SL Retrofit Retainer Strap Retrofit retainer strap for beam clamps Finish: Electro-galvanized Rod Size RS 034SL0600EG 3/ /8 034SL0800EG 3/ /8 034SL1000EG 3/ /8 034SL1200EG 3/ /8 034SL1400EG 3/ /8 A B Field bend and use jam nut over hanger rod to secure. Add 2 to width of flange to determine minimum length strap required. Structural Attachments 48

49 PH Multi-Purpose Purlin Clamp Attaches to bottom of purlins and beams to support threaded rod Finish: Electro-galvanized Rod Size RS Flange Thickness FT B Torque TQ Static Load 1 F1 Static Load 2 F2 Nut Included PH4 1/4 1/4 Max 3/4 Min 30 in lb 200 lb 160 lb No PH6 3/8 1/4 Max 3/4 Min 30 in lb 200 lb 160 lb No PH6FP 3/8 1/4 Max 3/4 Min 30 in lb 200 lb - Yes A jam nut is required for fire protection applications. Refer to Static Load 1 when attaching to C and Z purlins. Refer to Static Load 2 when attaching to a flat flange. Recognizing that torque wrenches are generally not used or available on many job sites, the setscrew should be tightened so it contacts the I-beam and then an additional 1/4 to 1/2 turn added. Structural Attachments 49

50 PHSW Multi-Purpose Purlin Clamp with Swivel Attachment to bottom of purlins and beams to support threaded rod Swivel feature option for attachment to purlins under sloped roofs Finish: Electro-galvanized Rod Size RS Flange Thickness FT B Torque TQ Static Load 1 F1 Static Load 2 F2 Nut Included PHSW4 1/4 1/4 Max 3/4 Min 30 in lb 200 lb 160 lb No PHSW6 3/8 1/4 Max 3/4 Min 30 in lb 200 lb 160 lb No PHSW6FP 3/8 1/4 Max 3/4 Min 30 in lb 200 lb - Yes A jam nut is required for fire protection applications. Refer to Static Load 1 when attaching to C and Z purlins. Refer to Static Load 2 when attaching to a flat flange. Recognizing that torque wrenches are generally not used or available on many job sites, the setscrew should be tightened so it contacts the I-beam and then an additional 1/4 to 1/2 turn added. Structural Attachments 50

51 315 Malleable Iron Purlin Clamp Attaches to lower flange of metal beams or purlins Supports 45 flanges up to 2 long, and 90 flanges up to 1-1/2 high Material: Cast iron Rod Size RS Flange Thickness FT A B Screw Diameter Sc Torque TQ Pipe Size Static Load F Finish: Electro-galvanized EG 3/8 1 Max 2 1 1/2 3/8 5 ft lb 4 Max 400 lb Finish: Plain PL 3/8 1 Max 2 1 1/2 3/8 5 ft lb 4 Max 400 lb Setscrew must be tightened and torqued onto the sloped side of the I-beam. Install in accordance with applicable code. Recognizing that torque wrenches are generally not used or available on many job sites, the setscrew should be tightened so it contacts the I-beam and then an additional 1/4 to 1/2 turn added. 547/548 C-Clamp For use on steel beams and purlins Finish: Plain Rod Size RS A B Screw Diameter Sc Screw Length L Torque TQ Static Load F Setscrew must be tightened and torqued onto the sloped side of the I-beam. Recognizing that torque wrenches are generally not used or available on many job sites, the setscrew should be tightened so it contacts the I-beam and then an additional 1/4 to 1/2 turn added. Listings Approvals PL 3/ /16 3/8 1 3/4 5 ft lb 250 lb cul, UL, FM PL 1/2 1 1/8 1 1/4 1/2 1 3/4 11 ft lb 250 lb FM Structural Attachments 51

52 325 Steel Side Beam Attachment Fastens to the wall or the side of a joist to support hanger rod Conforms with Federal Specification WW-H-171 (Type 35), Manufacturers Standardization Society ANSI /MSS-SP-58 (Type 34) Rod Size RS Hole Size HS Hole Type A Static Load 1 F1 Finish: Electro-galvanized Static Load 2 F EG 3/8 7/16 Plain 1 5/ lb 1,150 lb EG 1/2 9/16 Plain 1 5/ lb 1,150 lb EG 5/8 11/16 Plain 1 3/8 850 lb 2,000 lb EG 3/4 13/16 Plain 1 3/4 900 lb 3,500 lb EG 7/8 15/16 Plain 2 1/2 900 lb 3,600 lb EG 1 1 1/16 Plain 2 1/2 900 lb 3,700 lb Finish: Plain PL 3/8 7/16 Plain 1 5/ lb 1,150 lb PL 1/2 9/16 Plain 1 5/ lb 1,150 lb PL 5/8 11/16 Plain 1 3/8 850 lb 2,000 lb PL 3/4 13/16 Plain 1 3/4 900 lb 3,500 lb PL 7/8 15/16 Plain 2 1/2 900 lb 3,600 lb PL 1 1 1/16 Plain 2 1/2 900 lb 3,700 lb Refer to Static Load 1 when used with lag screw. Refer to Static Load 2 with bolt to steel. Follow fastener manufacturer s recommended shear and pull-out strength when fastening to the structure. Fastener not included. Install in accordance with applicable code. Structural Attachments 52

53 327 Malleable Iron Side Beam Attachment Pre-threaded structural attachment fastened to wall or the side of a joist to support hanger rod where two #43 Wood Drive Screws are necessary for proper support Rod Size RS A B Screw Diameter Sc Finish: Electro-galvanized Static Load F EG 3/8 2 3/8 15/16 # lb EG 1/2 2 3/4 1 5/16 # lb Finish: Plain PL 3/8 2 3/8 15/16 # lb PL 1/2 2 3/4 1 5/16 # lb Load rating dependent on wood structure strength. Follow fastener manufacturer s recommended shear and pull-out strength when fastening to the structure. Fastener not included. Structural Attachments 53

54 326 Universal Steel Side Beam Attachment Fastens to the wall or the side of a joist to support hanger rod Either 3/8 or 1/2 fasteners can be used to reduce inventories Conforms with Federal Specification WW-H-171 (Type 35), Manufacturers Standardization Society ANSI /MSS-SP-58 (Type 34) Hole Size 1 HS1 Hole Size 2 HS2 Hole Size 3 HS3 Finish: Electro-galvanized A Static Load 1 F1 Static Load 2 F EG 7/16 9/16 9/32 1 5/ lb 620 lb Finish: Plain PL 7/16 9/16 9/32 1 5/ lb 620 lb Refer to Static Load 1 when used with lag screw. Refer to Static Load 2 with bolt to steel. Follow fastener manufacturer s recommended shear and pull-out strength when fastening to the structure. Fastener not included. Install in accordance with applicable code. Structural Attachments 54

55 329 Side Beam Attachment Supports pipe from wood, concrete or steel strutures Pre-threaded Finish: Electro-galvanized Rod Size RS Hole Size 1 HS1 Hole Size 2 HS2 Height H Length L Width W Static Load F EG 3/ lb Structure Fastener Type Fastener Quantity UL Nominal Pipe Size FM Nominal Pipe Size #14 x 2 Drive Screw 2 2 Max 3 Max Wood (Pre-drilling not Required) Wood (1/4 Pilot Hole Required) Steel (Minimum 16 GA) Install in accordance with applicable code. 1/4 x 1 1/2 Lag Bolt 2 2 Max 3 Max 1/4 x 2 Lag Bolt 2 2 Max 3 1/2 Max 3/8 x 3 Lag Bolt, Washer 1 2 Max 3 1/2 Max 1/2 x 3 Lag Bolt 1 4 Max 4 Max 3/8 Bolt, Washer, Nut 1 4 Max 4 Max 1/4 x 1 Self Drill & Tap Screw 2 4 Max 4 Max Concrete 3/8 Bolt 1 4 Max 4 Max Structural Attachments 55

56 328 Threaded Steel Side Beam Attachment Fastens to wall or the side of a joist to support hanger rod Pre-threaded Conforms with Federal Specification WW-H-171 (Type 35), Manufacturers Standardization Society ANSI /MSS-SP-58 (Type 34) Structural Attachments Rod Size RS Hole Size 1 HS1 Hole Size 2 HS2 Finish: Electro-galvanized A B C Static Load 1 F1 Refer to Static Load 1 when used with lag screw. Refer to Static Load 2 with bolt to steel. Follow fastener manufacturer s recommended shear and pull-out strength when fastening to the structure. Fastener not included. Install in accordance with applicable code. Static Load 2 F EG 3/8 17/32 13/32 2 9/ /4 560 lb 620 lb Finish: Plain PL 3/8 17/32 13/32 2 9/ /4 560 lb 620 lb PL 1/2 17/32 13/32 2 9/ /4 560 lb 620 lb 56

57 37 Steel Eye Socket Rod Hanger Joins hanger rod to a structure Finish: Pre-galvanized Rod Size RS Pipe Size Hole Size 1 HS1 Hole Size 2 HS2 Height H Width W Static Load F EG 3/8 3/4 4 1/2 1/4 2 1/4 1 1/8 250 lb EG 1/2 2 1/2 6 11/16-2 3/4 1 1/2 760 lb Load rating dependent on wood structure strength. Structural Attachments 57

58 38 Offset Steel Eye Socket Rod Hanger Structural attachment used to join hanger rod to a structure Provides full vertical rod adjustment Finish: Electro-galvanized Rod Size RS Pipe Size Hole Size 1 HS1 Hole Size 2 HS2 Height H Width W C D Static Load F EG 3/8 4 Max 1/2 1/4 3 1/4 1 1/8 1 3/16 3/4 250 lb Load rating dependent on wood structure strength. For 3/8 rod through 2 pipe, use two Model #43 Wood Drive Screws. For 3/8 rod through 4 pipe, use one Model #42 1/2 x 3 Lag Screw. Structural Attachments 58

59 365 Steel Wall or Ceiling Plate Structural attachment to support hanger rod from a ceiling or a wall Rod Size RS Hole Size HS Finish: Electro-galvanized A B Pipe Size Static Load F EG 3/8 5/16 5/16 2 1/4 2 Max 100 lb Finish: Copper electro plated CP 3/8 5/16 5/16 2 1/4 2 Max 100 lb Finish: Plain PL 3/8 5/16 5/16 2 1/4 2 Max 100 lb Follow fastener manufacturer s recommended shear and pull-out strength when fastening to the structure. Fastener not included. Structural Attachments 59

60 365M Malleable Iron Wall or Ceiling Plate Structural attachment to support hanger rod from a ceiling or a wall Material: Cast iron Rod Size RS Hole Size HS Finish: Electro-galvanized A B Pipe Size Static Load F 365M0037EG 3/8 5/16 15/ /16 2 Max 180 lb 365M0050EG 1/2 5/16 15/ /16 3 1/2 Max 180 lb Finish: Copper electro plated 365M0037CP 3/8 5/16 15/ /16 2 Max 180 lb 365M0050CP 1/2 5/16 15/ /16 3 1/2 Max 180 lb Finish: Plain 365M0037PL 3/8 5/16 15/ /16 2 Max 180 lb 365M0050PL 1/2 5/16 15/ /16 3 1/2 Max 180 lb Follow fastener manufacturer s recommended shear and pull-out strength when fastening to the structure. Fastener not included. Structural Attachments 60

61 352 Standard Duty Welded Wall Bracket Wall attachment to support or suspend static piping Conforms with Federal Specification WW-H-171 (Type 32), Manufacturers Standardization Society ANSI /MSS-SP-58 (Type 32) Finish: Plain Height H Width W A B C D E Hole Size HS Static Load F PL /2 1 1/4 1 1/ /16 1,500 lb PL /2 21 1/2 1 1/4 1 1/ /16 1,500 lb PL /2 1 1/4 1 1/ /16 1,500 lb Follow fastener manufacturer s recommended shear and pull-out strength when fastening to the structure. Fastener not included. Install in accordance with applicable code. Structural Attachments 61

62 353 Heavy Duty Welded Wall Bracket Wall attachment to support or suspend static piping Conforms with Federal Specification WW-H-171 (Type 33), Manufacturers Standardization Society ANSI /MSS-SP-58 (Type 33) Finish: Plain Height H Width W A B C D E Hole Size HS Static Load F PL /4 1 1/2 7/ /16 3,000 lb PL /8 1 3/ /16 3,000 lb PL /2 1 1/4 1 1/ /16 3,000 lb PL /4 1 1/2 1 1/ /16 3,000 lb Follow fastener manufacturer s recommended shear and pull-out strength when fastening to the structure. Fastener not included. Install in accordance with applicable code. Structural Attachments 62

63 370A Single Concrete Insert Plate and Rod Used to support hanger rod from metal deck-poured concrete ceiling For use when adjustment for concrete thickness is needed Finish: Plain Rod Size RS A B C Static Load F 370A0037PL 3/ / lb 370A0050PL 1/ / lb 370A0062PL 5/ / lb Threaded rod supplied with an Electro Zinc Plated finish. Maximum load ratings are dependent on many factors, which include, but are not limited to: type of concrete, depth of slab, location of anchor in slab, and depth of anchor in slab. Consult a professional engineer regarding anchor positioning. Structural Attachments 63

64 355 Concrete Insert Plate Structural attachment in all grades of concrete Knockout keeps interior empty during pour Allows for horizontal rod adjustment up to 1-1/4 355N Nut required for UL Listing and FM Approval Conforms with Federal Specification WW-H-171 (Type 19), Manufacturers Standardization Society ANSI /MSS-SP-58 (Type 18) Finish: Plain Rod Size RS PL 3/8, 1/2, 5/8, 3/4, 7/8 A B C Pipe Size Static Load F 1 5/8 3 9/ Max 1,200 lb Rod should be threaded through the nut until it tightens against the top of the insert. For installation, place knockout side down on concrete form and nail in place. Wire 12 piece of #4 reinforcing rod on both sides. After concrete pour, knockout can be removed with a screwdriver. Install in accordance with applicable code. Structural Attachments 64

65 355N Nut for 355 Series Insert nut for model 355 Concrete Insert Conforms with Federal Specification WW-H-171 (Type 19), Manufacturers Standardization Society ANSI /MSS-SP-58 (Type 18) Reduced support spacing is required. Install in accordance with applicable code. Rod Size RS Finish: Electro-galvanized A Pipe Size Static Load F 355N0025EG 1/4 1 1/4-240 lb 355N0037EG 3/8 1 1/4 4 Max 610 lb 355N0075EG 3/4 1 1/4 8 Max 1,200 lb 355N0087EG 7/8 1 1/4 10 Max 1,200 lb Finish: Plain 355N0025PL 1/4 1 1/4-240 lb 355N0037PL 3/8 1 1/4 4 Max 610 lb 355N0050PL 1/2 1 1/4 8 Max 1,130 lb 355N0062PL 5/8 1 1/4 8 Max 1,200 lb 355N0075PL 3/4 1 1/4 8 Max 1,200 lb 355N0087PL 7/8 1 1/4 10 Max 1,200 lb Structural Attachments 65

66 Rigid Bracing System The CADDY line of innovative rigid bracing products was designed to provide superior performance and meet the highest seismic load requirements. The products have been designed with the end user in mind and provide contractors with labor-saving features to promote quick and easy installation. The system of products supports lateral and longitudinal bracing and offers a wide range of structural and pipe attachments. : Patent-pending lateral braces eliminate need for multiple trips up and down ladders Adjustable design can be used with different brace pipe sizes, providing flexibility on the jobsite and reducing contractor inventory Snap-off bolt heads help make installation and inspection quick and easy Single wrench size installs all products For use with brace pipe lengths up to 19-8 (6m) culus Listed FM Approved OSHPD Pre-Approved (OPA ) to the 2010 California Building Code Bar Joist Attachment Page Adjustable I-Beam Attachment Page 70 I-Beam Attachment Page 71 Multi Attachment Page

67 Universal Structural Attachment Page 73 Easy Universal Sway Brace Page Standard Universal Sway Brace Page Quick Grip Jr. Lateral Sway Brace Page Quick Grip Lateral Sway Brace Page Shear Bolt Page 82 Shear Nut Page

68 Rigid Bracing System Bar Joist Attachment Can be installed on bar joists or I-beams Thumb spring retainer allows for ease of positioning Snap-off bolt head helps enable easy installation and inspection of seismic sway braces No assembly required No loose parts Meets NFPA -13 requirements for seismic sway bracing 68

69 Bar Joist Attachment Flange Thickness FT A B C Rigid Bracing System Finish: Electro-galvanized CSBBARJEG 1/4 1/ /2 Finish: Hot-dip galvanized CSBBARJHD 1/4 1/ /2 UL Loads Brace Direction to Structure Service Pipe Size Rating Parallel ,000 lb Perpendicular ,740 lb FM Loads Brace Direction to Structure Service Pipe Size Horizontal Capacity per Installation Angle from Vertical Parallel N/A 1,410 lb 2,110 lb 2,540 lb 2,830 lb Perpendicular N/A 1,740 lb 1,710 lb 2,060 lb 2,300 lb 69

70 Rigid Bracing System Adjustable I-Beam Attachment No loose parts No assembly required Snap-off bolt head helps enable easy installation and inspection of seismic sway braces Meets NFPA -13 requirements for seismic sway bracing Flange Thickness FT A Height H Finish: Electro-galvanized Length L CSBIB075085EG 1/4 3/ /2 2 1/ /4 CSBIB075145EG 1/4 3/4 8 1/2 14 1/2 2 1/ /4 CSBIB125180EG 3/4 1 1/ /2 21 1/2 3 1/8 Finish: Hot-dip galvanized CSBIB075085HD 1/4 3/ /2 2 1/ /4 CSBIB075145HD 1/4 3/4 8 1/2 14 1/2 2 1/ /4 CSBIB125180HD 3/4 1 1/ /2 21 1/2 3 1/8 Width W UL Loads Brace Direction to Structure Service Pipe Size Rating Parallel ,740 lb Perpendicular ,740 lb Brace Direction to Structure Service Pipe Size FM Loads Horizontal Capacity per Installation Angle from Vertical Parallel N/A 1,620 lb 1,710 lb 1,010 lb 1,110 lb Perpendicular N/A 1,620 lb 2,300 lb 2,820 lb 3,140 lb 70

71 I-Beam Attachment Rigid Bracing System Snap-off bolt head helps enable easy installation and inspection of seismic sway braces Meets NFPA -13 requirements for seismic sway bracing Finish: Electro-galvanized Flange Thickness FT Height H Width W CSBBC075EG 1/4 3/4 2 1/2 2 3/4 UL Loads Brace Direction to Structure Service Pipe Size Rating Parallel 1-4 1,200 lb Perpendicular 1-8 2,015 lb Brace Direction to Structure Service Pipe Size FM Loads Horizontal Capacity per Installation Angle from Vertical Parallel N/A 1,190 lb 1,680 lb 1,160 lb 1,280 lb Perpendicular N/A 1,620 lb 1,710 lb 1,010 lb 1,110 lb 71