SCION tc COIL OVER SUSPENSION Preparation

Size: px
Start display at page:

Download "SCION tc 2005-2008 COIL OVER SUSPENSION Preparation"

Transcription

1 SCION tc COIL OVER SUSPENSION Preparation Part Number: PTR NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: Item # Quantity Reqd. Description 1 1 Front shock body, left 2 1 Front shock body, right 3 2 Upper bearing adapter 4 2 Rear shock body 5 2 M12 x 1.50 Nylock nut 6 2 Coil spring 9.00" 7 2 Coil Spring 7.00" 8 1 Hardware Kit #1 9 2 Hardware Kit #2 Hardware Kit #1 Contents Item # Quantity Reqd. Description 1 2 Bump -stop/isolator 2 2 Spring perch 3 1 Install Instructions 4 1 Spanner wrench 5 1 Hex wrench, 3/16" 6 4 1/4-20 SHCS Stainless 7 4 HHCS, M8 x 1.25 x M8 flat washer 9 4 M8 x 1.25 Metal locknut /8-24 FULL height locknut 11 2 Flat washer M Sleeve, lower shock eye 13 2 Sleeve, shock stud 14 2 Washer, cup Hardware Kit #2 Contents Item # Quantity Reqd. Description 1 2 Spring Perch 2 2 Lower eye fabrication 3 2 Upper coil adapter 4 2 Bump stop 5 4 Shock grommet 6 4 Bushings Recommended Sequence of Application Item # Accessory 1 TRD Sway Bar can be installed at the same time. 2 TRD Wheel/Tire Package 3 Vehicle Services Parts (may be required for reassembly) Item # Quantity Reqd. Description Conflicts None General Applicability Scion tc: all mo dels Recommended Tools Personal & Vehicle Protection Fender Cover Seat Cover Special Tools Spring Compressor Spanner wrench Installation Tools Impact Wrench Special Chemicals WD-40 or similar light oil Notes Notes Provided in kit Notes For disassembly only Notes Legend STOP: Damage to the vehicle may occur. Do not proceed until process has been complied with. OPERATOR SAFETY: Use caution to avoid risk of injury. CAUTION: A process that must be carefully observed in order to reduce the risk of damage to the accessory/vehicle and to ensure a quality installation TOOLS & EQUIPMENT: Used in Figures calls out the specific tools and equipment recommended for this process. REVISION MARK: This mark highlights a change in installation with respect to previous issue. Issue A: 04/04/ of 16 DIO

2 Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation These guidelines can be found in the "Accessory Installation Practices" document. This document covers such items as: Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). Safety (eye protection, rechecking torque procedure, etc.). Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). Front Suspension 1. Measure and Record Current Ride Height of Vehicle. (a) Measuring from center of axle to fender edge will prevent a discrepancy when changing wheels or tires. 2. Remove Front Wheel. 3. Remove Front Wiper Arms. 4. Remove Cowl Cover. 5. Disconnect Sway Bar Link Issue A: 04/04/ of 16 DIO

3 6. Disconnect Speed Sensor Wire (if equipped) 7. Remove Front Shock Absorber with Coil Spring (a) Remove the front suspension support dust cover. (save for re-use) (b) Loosen the lock nut. (do not remove the lock nut.) (c) Remove the 2 nuts on the lower side of the shock absorber with coil spring. (d) Remove the 3 nuts on the upper side of the shock absorber with coil spring. (1) Support the weight of the strut assembly when removing the last nut and ease the assembly out of the wheel well. Issue A: 04/04/ of 16 DIO

4 8. Disassemble Strut Assembly (a) Compress the coil spring. (b) Remove the lock nut. (c) Remove the suspension support. (save for reuse) (d) Remove the coil spring seat upper. (e) Save the rest of the assembly for the customer or discard at their request per your local state laws. 9. Assemble Front Coil-Over Assembly NOTE: Refer to the parts description and photo on pages 1&2 to identify the components of the TRD coil-overs. (a) Pull the rod out of a front shock body until it stops. (b) Thread a coil spring perch as far down the threaded area on the shock body as possible (it will contact the end link bracket). The lip on the coil spring perch should be facing the top of the shock. (c) Install a 1/4-20 set screw about 2-3 threads deep. Do not tighten it at this time. Issue A: 04/04/ of 16 DIO

5 (d) Thread a bump stop/isolator on one end of a front coil spring. TIP: Push the edge of the bump stop lip onto the flat surface under the top coil of the spring. Turn the bump stop clockwise while pressing down. Continue until the lip is fully positioned under the top coil (about 1.2 turns). The top surface of the bump stop will follow the shape of the spring s top surface. (e) Place the coil spring on the TRD shock with the bump stop at the top. (f) Position the upper bearing adaptor over the bump stop. NOTE: Make sure the protrusion is seated in the hole at the top of the bump stop/isolator. (g) Install the factory front suspension support dust seal over the protrusion on the top of the upper bearing adaptor. Issue A: 04/04/ of 16 DIO

6 (h) Place the factory front suspension support assembly over the upper bearing adaptor until it is seated on the dust seal. (i) Install the TRD-supplied M12 flat washer and M12 x 1.50 locknut on the shock shaft. Torque: 47.5 N m (483 kgf cm, 35 ft.-lbs.) (j) Install the factory dust cap on the front suspension support. (k) Apply a pre-load to the spring by handturning the spring perch to show 2 3/8 inches or 60mm of thread below the perch. NOTE: Apply a small amount of light lubricant (i.e. WD-40) to the shock body threads to make adjustment easier. HINT: With the perch at the bottom, make aligning marks on both the spring perch and the shock body for reference. 10. Install Coil-Over Assembly (a) Feed assembly up into fender apron and tighten 3 nuts holding assembly in place. Torque: 52 N m (530 kgf cm, 38 ft lbf) (b) Attach the coil-over to the knuckle assembly. Torque: 240 N m (2,450 kgf cm, 177 ft lbf) (c) Tighten the lock nut at the top of the coil-over shock assembly. Torque: 47 N m (480 kgf cm, 35 ft lbf) (d) Install suspension dust cover. (e) Install front speed sensor line. Torque: 19 N m (194 kgf cm, 14 ft lbf) Issue A: 04/04/ of 16 DIO

7 (f) Attach front stabilizer link. Torque: 74 N m (755 kgf cm, 55 ft lbf) HINT: Use a 6 mm hexagon wrench to hold the stud if the ball joint turns together with nut. (g) Install front wheel Torque: 103 N m (1,050 kgf cm, 76 ft lbf) (h) Install the cowl top ventilator louver. (i) Install wiper arms. (see illustration) (j) Install wiper arm head caps. (k) Inspect and adjust front wheel alignment. 11. Remove Rear OE Shock Assemblies (a) Fold rear seats forward. (b) Remove trunk interior components shown. Issue A: 04/04/ of 16 DIO

8 (c) Pull rear and top edges of No. 1 side trim assembly loose from the body. (d) Remove the deck trim side panel assemblies. (1) Remove luggage hooks. Insert a 3 mm hexagon wrench or small screw driver into hole A to disengage the claws, then remove luggage hook from side panel. (e) Remove rear wheels (f) Disconnect the skid control sensor wire. (1) Disconnect the skid control sensor connector. (2) Remove the bolt and wire bracket. (g) Disconnect rear stabilizer bar link. HINT: If the ball joint turns together with the nut, use a 5 mm hexagon wrench to hold the stud. Issue A: 04/04/ of 16 DIO

9 (h) Remove the shock absorber with coil spring. (1) Remove the bolt and nut from the lower suspension arm. NOTICE: Unscrew the bolt and not the nut. The nut is a locking nut. (2) Remove the 3 nuts. (3) Pull shock assembly from the vehicle. 12. Disassemble Rear Shock Assembly (a) Compress the coil spring. (b) Remove the lock nut. (1) Using a 6 mm hexagon wrench to hold the piston rod, remove the nut. (c) Disassemble the rest of the parts. (d) Save the No. 1 cushion washer, bracket subassembly, and the coil spring upper insulator for reuse. (e) Save the rest of the assembly for the customer or discard at their request per your local state laws. Issue A: 04/04/ of 16 DIO

10 (f) Remove the skirted area from the upper spring insulator using tin snips or a box cutter. NOTE: Be sure to cut it flush with the surrounding material to create a flat surface. 13. Assemble Rear Coil-Over (a) Pull the rod out of a rear shock body until it stops. Do not force it. (b) Thread a coil spring perch towards the bottom of the threaded area on the shock body. You should measure ¾ or 20mm of thread below the spring perch. Refer to picture for the proper orientation. (c) Insert two shock eye bushings (do not grease the outside of the bushings) from each side into the shock eye. Issue A: 04/04/ of 16 DIO

11 (d) Grease one of the 1" OD shock eye spacer tubes with chassis lube and insert it into the bushings inserted in Step 13-C. (e) Assemble the lower shock eye to the shock body using two M8 x 1.25 x 60 bolts, two M8 x 1.25 locknuts and four M8 flat washers. Torque: 19 N m (193 kgf cm14 ft.-lbs. (f) Press a bump stop down on the shock rod just past the bump stop ring as shown. (g) Place a coil spring onto the TRD shock assembly. (h) Place an upper coil spring adaptor onto the top of the spring. Issue A: 04/04/ of 16 DIO

12 (i) Place a factory rear shock absorber cushion washer on the shock shaft. NOTE: The flange of the washer faces up. (j) Install one suspension support grommet, with a 9/16" OD spacer tube inserted, into a rear spring front bracket sub-assembly from the bottom. Make sure the upper insulator is seated properly. NOTE: Place a thin layer of chassis lube on the outside surface of the spacer tube before inserting it into the grommets. (k) Place a second suspension support grommet over the spacer tube as it protrudes up through the top of the rear spring front bracket sub-assembly. See picture for the proper orientation. (l) Install the completed rear spring bracket on the shock shaft until it seats squarely on the rear shock absorber cushion washer. Issue A: 04/04/ of 16 DIO

13 (m) Install a 3/8-24 locknut and cup washer on the shock shaft. Torque: 27 N m (276 kgf cm, 20 ft.-lbs.) (n) Apply a pre-load to the spring by turning the spring perch so that ¾ or 20 mm of threads are showing below the spring perch. NOTE: Apply a small amount of light lubricant (i.e. WD-40) to the shock body threads to make adjustment easier. 14. Install Rear Coil-Over Assemblies (a) Attach top of coil-over assembly to the vehicle floor. Torque: 80 N m (816 kgf cm, 59 ft lbf) (b) Install lower nut and bolt finger tight. Issue A: 04/04/ of 16 DIO

14 (c) Connect the stabilizer link with nut. Torque: 44 N m (449 kgf cm, 32 ft lbf) HINT: If the ball joint turns together with the nut, use a 5 mm hexagon wrench to hold the stud. (d) Connect the wheel speed sensor and re-attach wire bracket. Torque: 5.0 N m (51 kgf cm, 44 in lbf) (e) Install rear wheel. (1) Tighten lug nuts in a star pattern. Torque: 103 N m (1,050 kgf cm, 76 ft lbf) (f) Lower vehicle and settle the suspension by bouncing the vehicle several times. (g) Fully tighten lower shock mount bolt. Torque: 140 N m (1,430 kgf cm, 103 ft lbf) 15. Adjust Vehicle Ride Height. (a) Drive vehicle around the block to settle the suspension. (b) Measure ride height in the same location as you did in the beginning of the process. (c) TRD recommends lowering the vehicle no more than 1 ¾ inches from stock ride height with this system. (d) Make notes as to which corners you would like to raise or lower at this point. Issue A: 04/04/ of 16 DIO

15 (e) Raise the vehicle. (f) Remove the wheels. (if necessary) (g) Loosen the spring perch set screw. (h) Use the reference marks made on the spring perch and shock body and turn the spring perch counterclockwise to lower the ride height or clockwise to raise the ride height. NOTE: Each full turn of the lower spring collar will result in approximately 1/16" of ride height change. 16 turns = 1 inch. (i) At lower than TRD recommended settings, proper alignment may not be possible and the rear upper spring perches may not stay properly seated. (j) Tighten the spring perch set screw. (k) Replace the wheels and torque the lug nuts. (l) Set the vehicle back on the ground. NOTE: Since the suspension "droops" when raised, drive a short distance to "settle" the suspension and then re-check the ride height. Item / Front Specified Condition Toe-In ' ( ) Total Toe mm ( in.) Camber -0 31' +- 45' ( ) Right-left error 45' (0.75 ) or less Caster 3 02' +- 45' ( ) Right-left error 45' (0.75 ) or less Item / Rear Specified Condition Toe-in 0 18' +- 6' ( ) Total Toe mm ( in.) Camber -0 56' +- 20' ( ) Cross Camber 30' (0.5 ) or less 16. Align Suspension Front and Rear. (a) Take vehicle to your local dealer for proper alignment. Issue A: 04/04/ of 16 DIO

16 Checklist. These points MUST be checked to ensure a quality installation. CHECK FOR: LOOK FOR: Accessory Function Checks Listen for clunk noises Confirm springs are fully seated properly. Vehicle Function Checks Confirm ABS VSC light is not on. Confirm speed sensor connector is fully seated. Issue A: 04/04/ of 16 DIO

REAR SHOCK ABSORBER WITH COIL SPRING

REAR SHOCK ABSORBER WITH COIL SPRING 278 OVERHAUL COMPONENTS: see page 272. 1. REMOVE TONNEAU COVER ASSY (SEE PAGE 7627) 2. REMOVE DECK BOARD SUBASSY (SEE PAGE 7627) 3. REMOVE BACK DOOR SCUFF PLATE (SEE PAGE 7627) 4. REMOVE DECK FLOOR BOX

More information

INSTALLATION INSTRUCTIONS COMPETITION SERIES COILOVER SUSPENSION SYSTEM 03+ Scion xb

INSTALLATION INSTRUCTIONS COMPETITION SERIES COILOVER SUSPENSION SYSTEM 03+ Scion xb INSTALLATION INSTRUCTIONS COMPETITION SERIES COILOVER SUSPENSION SYSTEM 03+ Scion xb NOTE: Progress Technology products should only be installed by a qualified licensed mechanic experienced in the installation

More information

SCION FR-S 2013 - PERFORMANCE AIR INTAKE Preparation 2.0L F-4

SCION FR-S 2013 - PERFORMANCE AIR INTAKE Preparation 2.0L F-4 Preparation 2.0L F-4 Part Number: PTR03-18130 Please see Page 12 for important Care and Maintenance information! Kit Contents Item # Qty. Service Part # Description 1 1 PTR03-18130-AC TRD Air Box Base

More information

TOYOTA Tundra 2007 - BACK-UP CAMERA SYSTEM Preparation

TOYOTA Tundra 2007 - BACK-UP CAMERA SYSTEM Preparation Preparation Part Number(s): PT233-34070, PT923-35070-11, PT923-35070-43 NOTE: Part number of this accessory may not be the same as part number shown. Back Up Monitor Kit Contents PT923-35070-11 / PT923-35070-43

More information

»Product» Safety Warning

»Product» Safety Warning C1200 Installation Instructions 2007-2016 Chevy/GM 1500 2/4wd 2" Strut Spacer Lift Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone Offroad

More information

2011-14 F250 6 RADIUS ARM KIT

2011-14 F250 6 RADIUS ARM KIT 92154000 Thank you for choosing Rough Country for your suspension needs. 2011-14 F250 6 RADIUS ARM KIT Rough Country recommends a certified technician installs this system. In addition to these instructions,

More information

WARNING TO END USER, INSTALLER AND SELLER OF THIS PART!

WARNING TO END USER, INSTALLER AND SELLER OF THIS PART! WARNING TO END USER, INSTALLER AND SELLER OF THIS PART! By installing this part you are accepting full responsibility and liability for proper wheel and tire fitment after installation. It is the installer

More information

FRONT SUSPENSION Click on the applicable bookmark to selected the required model year

FRONT SUSPENSION Click on the applicable bookmark to selected the required model year FRONT SUSPENSION 33A-2 FRONT SUSPENSION General Information GENERAL INFORMATION 33200010105 The front suspension on 2WD vehicles is an independent suspension system having the double wishbone combined

More information

INSTALLATION INSTRUCTIONS. 6111 Air Spring Kit 2011+ Ford F250/F-350 Single Wheel 2WD 2011+ Ford F350 Dually 2WD IMPORTANT NOTES

INSTALLATION INSTRUCTIONS. 6111 Air Spring Kit 2011+ Ford F250/F-350 Single Wheel 2WD 2011+ Ford F350 Dually 2WD IMPORTANT NOTES INSTALLATION INSTRUCTIONS 6111 Air Spring Kit 2011+ Ford F250/F-350 Single Wheel 2WD 2011+ Ford F350 Dually 2WD Thank you for purchasing a quality Hellwig Product. PLEASE READ THIS INSTRUCTION SHEET COMPLETELY

More information

LIFT-505. BMF Lift Kit. Yamaha Drive Gas or Electric. Installation Instructions

LIFT-505. BMF Lift Kit. Yamaha Drive Gas or Electric. Installation Instructions LIFT-505 BMF Lift Kit Yamaha Drive Gas or Electric Installation Instructions Contents of LIFT-505 Yamaha Drive BMF Lift Kit: a (1 ea.) BMF A-Arm Assembly b (1 ea.) Driver Side Shock Tower c (1 ea.) Passenger

More information

ReadyLift (Part# 66-5075) Strut Extension, Installation Instructions Toyota Tundra New Body Style 2WD & 4WD

ReadyLift (Part# 66-5075) Strut Extension, Installation Instructions Toyota Tundra New Body Style 2WD & 4WD SAFETY WARNING: recommends this system be installed by a professional technician. In addition to these instructions, professional knowledge of disassembly/ reassembly procedures and post installation checks

More information

SCION tc 2005 - DASH APPLIQUE Preparation

SCION tc 2005 - DASH APPLIQUE Preparation Preparation Part Number: PTS10-21051 Kit Contents Item # Quantity Reqd. Description 1 1 HVAC Center Vent Trim 2 1 Radio Cover Assy (2 pieces) 3 1 HVAC Control Panel (3 pieces) 4 1 Shift Surround 5 1 Driver

More information

STEERING HANDLEBAR/FRONT WHEEL/ FRONT SHOCK ABSORBER

STEERING HANDLEBAR/FRONT WHEEL/ FRONT SHOCK ABSORBER 14 14 STEERING HANDLEBAR/FRONT WHEEL/ SCHEMATIC DRAWING ------------------------------------------------- 14-1 SERVICE INFORMATION------------------------------------------------ 14-2 TROUBLESHOOTING-----------------------------------------------------

More information

Ford F-250 / 350 2-1/2 Coil Kit. Ford F-250, F350 2011-2015. Part#: 013255

Ford F-250 / 350 2-1/2 Coil Kit. Ford F-250, F350 2011-2015. Part#: 013255 Part#: 013255 Ford F-250 / 350 2-1/2 Coil Kit Ford F-250, F350 2011-2015 Rev.040815 491 W. Garfield Ave., Coldwater, MI 49036. Phone: 517-279-2135 Web/live chat: www.bds-suspension.com. E-mail: tech@bds-suspension.com

More information

MEASURING WHEEL ALIGNMENT

MEASURING WHEEL ALIGNMENT MEASURING WHEEL ALIGNMENT 2003-04 WHEEL ALIGNMENT Specifications & Procedures - Hummer - H2 Steering and vibration complaints are not always the result of improper alignment. One possible cause is wheel

More information

Model Year: 2010 Model: Prius Doc ID: RM000001Y3B015X. Title: ALIGNMENT / HANDLING DIAGNOSIS: FRONT WHEEL ALIGNMENT: ADJUSTMENT (2010 Prius)

Model Year: 2010 Model: Prius Doc ID: RM000001Y3B015X. Title: ALIGNMENT / HANDLING DIAGNOSIS: FRONT WHEEL ALIGNMENT: ADJUSTMENT (2010 Prius) Last Modified: 5-3-2010 6.4 N From: 200904 Model Year: 2010 Model: Prius Doc ID: RM000001Y3B015X Title: ALIGNMENT / HANDLING DIAGNOSIS: FRONT WHEEL ALIGNMENT: ADJUSTMENT (2010 Prius) ADJUSTMENT If the

More information

CorkSport Mazdaspeed 6 Rear Sway Bar 2006-2007 Mazdaspeed 6

CorkSport Mazdaspeed 6 Rear Sway Bar 2006-2007 Mazdaspeed 6 CorkSport Mazdaspeed 6 Rear Sway Bar 2006-2007 Mazdaspeed 6 Pre-Installation Notes: The CorkSport Rear Sway Bar is a great addition to improving the handling performance to the Mazdaspeed 6. It will minimize

More information

FRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER

FRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 FRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER Please read before beginning Stainless steel hardware

More information

16 April 2012 1032011-F 1994-2002 Dodge Adjustable Track bar with Relocation Bracket 1

16 April 2012 1032011-F 1994-2002 Dodge Adjustable Track bar with Relocation Bracket 1 16 April 2012 1032011-F 1994-2002 Dodge Adjustable Track bar with Relocation Bracket 1 BD Adjustable Track Bar w/bracket Dodge 2500-3500 4WD Models 1994-2002 Dodge 1500 4WD Model 1994-2001 P/N# 1032011-F

More information

MM Adjustable Tie-Rod Ends (MMTR-2, -4, -7)

MM Adjustable Tie-Rod Ends (MMTR-2, -4, -7) 3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com MM Adjustable Tie-Rod Ends (MMTR-2, -4, -7) PLEASE NOTE: The use of 1996-2004

More information

INSTALLATION INSTRUCTIONS. 6108 Air Spring Kit 2011+ Ford F250 Single Wheel 4WD 2011+ Ford F350 Dually 4WD (2011 F350 Single Wheel 4WD use p/n 6113)

INSTALLATION INSTRUCTIONS. 6108 Air Spring Kit 2011+ Ford F250 Single Wheel 4WD 2011+ Ford F350 Dually 4WD (2011 F350 Single Wheel 4WD use p/n 6113) INSTALLATION INSTRUCTIONS 6108 Air Spring Kit 2011+ Ford F250 Single Wheel 4WD 2011+ Ford F350 Dually 4WD (2011 F350 Single Wheel 4WD use p/n 6113) Thank you for purchasing a quality Hellwig Product. PLEASE

More information

Rating when used as a weight carrying hitch without spring bars:

Rating when used as a weight carrying hitch without spring bars: BOLT-TOGETHER WEIGHT DISTRIBUTING HITCH SYSTEM Rating when used as a weight distributing hitch with spring bars: Part Number 48051 4805 48053 48054 Max Tongue Weight 550 Ibs. 750 Ibs. 1000 Ibs. 1400 lbs.

More information

MUSTANG II IFS COMPLETE PARTS PACKAGE

MUSTANG II IFS COMPLETE PARTS PACKAGE MUSTANG II IFS COMPLETE PARTS PACKAGE Your Southern Rods & Parts Mustang II IFS Parts Package contains the following items: 1 pr) Upper Control Arms (2023) 1) Upper Arm Bolt Kit (MP-001-A) 1 pr) Lower

More information

88-98 Chevy / GMC Fullsize 4WD 6-Lug 2"- 2 1/2" Suspension Lift Installation Instructions

88-98 Chevy / GMC Fullsize 4WD 6-Lug 2- 2 1/2 Suspension Lift Installation Instructions 88-98 Chevy / GMC Fullsize 4WD 6-Lug 2"- 2 1/2" Suspension Lift Installation Instructions Safety Glasses Metric / Standard Wrenches & Sockets Floor Jack Jack Stands Hack Saw Ball Joint Seperator Measuring

More information

DANA 30 MANUAL HUB CONVERSION KIT

DANA 30 MANUAL HUB CONVERSION KIT DANA 30 MANUAL HUB CONVERSION KIT 12194 PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE YOU BEGIN Your safety and the safety of other motorists is very important. Your Jeep is an off road capable vehicle

More information

WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES

WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES 1998 Mitsubishi Montero 1997-98 WHEEL ALIGNMENT Mitsubishi - Specifications & Procedures Diamante, Eclipse, Galant, Mirage, Montero, Montero Sport, 3000GT RIDING

More information

1993 SUSPENSION Volkswagen Front. EuroVan

1993 SUSPENSION Volkswagen Front. EuroVan Article Text ARTICLE BEGINNING 1993 SUSPENSION Volkswagen Front EuroVan DESCRIPTION FWD independent suspension is an double-wishbone type with torsion bars mounted on upper control arm. Wheel is supported

More information

Volkswagen Jetta, Golf, GTI 1999, 2000 Brake System 47 Brakes - Hydraulic Components (Page GR-47)

Volkswagen Jetta, Golf, GTI 1999, 2000 Brake System 47 Brakes - Hydraulic Components (Page GR-47) 47 Brakes - Hydraulic Components (Page GR-47) FS III front brake calipers, servicing Front brake caliper piston, removing and installing FN 3 front brake calipers, servicing Front caliper piston, removing

More information

TRANS-05, Torque Tube Removal, Rebuilding, and Installation

TRANS-05, Torque Tube Removal, Rebuilding, and Installation TRANS-05, Torque Tube Removal, Rebuilding, and Installation Tools Metric Wrench Set Metric Socket Set Jack Stands (6 minimum) Floor Jack 8mm Cheesehead socket (also referred to as 12 point internal socket

More information

SELF-STEERING AXLE TABLE OF CONTENTS

SELF-STEERING AXLE TABLE OF CONTENTS SELF-STEERING AXLE TABLE OF CONTENTS Section 1 - Introduction Section 2 - Pre-Installation Check List Section 3 - Ride Height Adjustments Section 4 - Suspension Mount Section 5 - Axle Mount Section 6 -

More information

INSTRUCTIONS. FLHR/C/S (Road King) FRONT END LOWERING KIT 1WARNING -J03242 REV. 10-19-04. General. Removal (Left and Right Forks) Kit Number 54614-05

INSTRUCTIONS. FLHR/C/S (Road King) FRONT END LOWERING KIT 1WARNING -J03242 REV. 10-19-04. General. Removal (Left and Right Forks) Kit Number 54614-05 INSTRUCTIONS -J04 REV. 0-9-04 General FLHR/C/S (Road King) FRONT END LOWERING KIT This kit is designed for installation on 00 and later FLHR/C/S Model Motorcycles. Road King models use the conventional

More information

(A4) Suspension and Steering Sample Questions and Answers

(A4) Suspension and Steering Sample Questions and Answers (A4) Suspension and Steering Sample Questions and Answers Answers to these questions are found beginning on page 4 of this document 1. Two technicians are discussing the replacement of an inner tie rod

More information

2014-2015 GM 1500 Pick-Up 4WD 4" Suspension Lift Installation Instructions

2014-2015 GM 1500 Pick-Up 4WD 4 Suspension Lift Installation Instructions 2014-2015 GM 1500 Pick-Up 4WD 4" Suspension Lift Installation Instructions www.skyjacker.com Required Tool List: * Safety Glasses * Metric / Standard Wrenches & Sockets * Allen Wrenches * Floor Jack *

More information

WHEEL ALIGNMENT 4WD SA 6

WHEEL ALIGNMENT 4WD SA 6 SA6 WHEEL ALIGNMENT 4WD 1. MAKE FOLLOWING CHECKS AND CORRECT ANY PROBLEMS (a) Check the tires for wear and proper inflation. Cold tire inflation pressure: See page A25 (b) Check the wheel runout. Lateral

More information

6 inch A-Arm Lift Kit WARNING: 16-018/16-019. installation instructions. will fit CLUB CAR DS. included:

6 inch A-Arm Lift Kit WARNING: 16-018/16-019. installation instructions. will fit CLUB CAR DS. included: Revised May 205 6-08/6-09 6 inch A-Arm Lift Kit will fit CLUB CAR DS installation instructions included: Rear Lift Blocks Main Suspension Assembly Spindles A-Arms Rear Shock Mounting Plates U-Bolts WARNING:

More information

READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS PRIOR TO INSTALLATION OF SYSTEM AND OPERATION OF VEHICLE.

READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS PRIOR TO INSTALLATION OF SYSTEM AND OPERATION OF VEHICLE. 491 W. Garfield Ave., Coldwater, MI 49036 Phone: 517-279-2135 Web/live chat: www.bds-suspension.com E-mail: tech-bds@sporttruckusainc.com Product: GM Leaf Spring READ AND UNDERSTAND ALL INSTRUCTIONS AND

More information

Unit: mm(in) Item Standard value Service limit Axle shaft run out - 0.2(0.008)

Unit: mm(in) Item Standard value Service limit Axle shaft run out - 0.2(0.008) Rear Wheel/Brake/Suspension 13. Rear Wheel/Brake/Suspension Service Information 13-1 Troubleshooting 13-2 Rear Wheel 13-3 Rear Cushion 13-4 Rear Swing Arm 13-7 Service Information General Safety If the

More information

Installation manual. 3 suspension system. 2009-2013 Ford F150. Part # 23000. Part # 23000. Important customer information: 2009-2013 Ford F150

Installation manual. 3 suspension system. 2009-2013 Ford F150. Part # 23000. Part # 23000. Important customer information: 2009-2013 Ford F150 Installation manual 3 suspension system 2009-2013 Ford F150 Part # 23000 sj12112012rev.03 Part # 23000 2009-2013 Ford F150 3 suspension system Part # Description Qty. 23000-01 Driver side upper control

More information

Installation Guide for the TJ LCG PRO Suspension System (Low Center of Gravity) Available 4 or 5

Installation Guide for the TJ LCG PRO Suspension System (Low Center of Gravity) Available 4 or 5 INSTALLATION GUIDE Installation Guide for the TJ LCG PRO Suspension System (Low Center of Gravity) Available 4 or 5 Take every precaution to make this installation a safe procedure. Make safety the number

More information

4.5 LIFT BOX KIT 2009 2013 DODGE RAM 2500 & 3500 4WD DIESEL ENGINE ONLY FTS23031

4.5 LIFT BOX KIT 2009 2013 DODGE RAM 2500 & 3500 4WD DIESEL ENGINE ONLY FTS23031 4.5 LIFT BOX KIT 2009 2013 DODGE RAM 2500 & 3500 4WD DIESEL ENGINE ONLY FTS23031 Fabtech Motorsports 4331 Eucalyptus Ave. Chino, CA 91710 Tech Line 909-597-7800 Fax 909-597-7185 Web www.fabtechmotorsports.com

More information

758 Heavy-duty Ratchet Guy Wire Cutter

758 Heavy-duty Ratchet Guy Wire Cutter INSTRUCTION MANUAL 758 Heavy-duty Ratchet Guy Wire Cutter Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. Register this product

More information

Competition 4 & 6 suspension Lift Toyota Landcruiser & nissan patrol

Competition 4 & 6 suspension Lift Toyota Landcruiser & nissan patrol Competition 4 & 6 suspension Lift Toyota Landcruiser & nissan patrol Competition suspension Product Guidelines Guidelines for sale and recommendation of 4 (100mm) and 6 (150mm) Lifts for Toyota Landcruiser

More information

SLACK PERFORMANCE KARTS

SLACK PERFORMANCE KARTS SLACK PERFORMANCE KARTS SET UP GUIDE Thank you for purchasing a 2013 Slack Axiom Chassis. Performance Mfg. strives to provide you with the very best chassis and components on the market today. Your satisfaction

More information

POWER LOCK KIT GENERAL INSTALLATION -J04427 REV. 2007-12-04. Kit Number. Models. Additional Parts Required. Kit Contents

POWER LOCK KIT GENERAL INSTALLATION -J04427 REV. 2007-12-04. Kit Number. Models. Additional Parts Required. Kit Contents -J0 REV. 00--0 POWER LOCK KIT GENERAL Kit Number -0, 0-0 Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section of www.harleydavidson.com (English

More information

WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES

WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES For 1234 1992 WHEEL ALIGNMENT Subaru Specifications & Procedures Justy, Legacy, Loyale, SVX * PLEASE READ THIS FIRST * NOTE: Prior to performing wheel alignment,

More information

Volkswagen Jetta, Golf, GTI 1999, 2000 Brake System 46 Brakes - Mechanical Components (Page GR-46)

Volkswagen Jetta, Golf, GTI 1999, 2000 Brake System 46 Brakes - Mechanical Components (Page GR-46) 46 Brakes - Mechanical Components (Page GR-46) Front brakes Brake pads, removing and installing Brake pads, removing and installing FN 3 brake caliper, servicing FS III brake caliper, servicing Rear wheel

More information

Rebuild Instructions for 70001 and 70010 Transmission

Rebuild Instructions for 70001 and 70010 Transmission Rebuild Instructions for 70001 and 70010 Transmission Brinn, Incorporated 1615 Tech Drive Bay City, MI 48706 Telephone 989.686.8920 Fax 989.686.6520 www.brinninc.com Notice Read all instructions before

More information

DO NOT attempt to repair hub and wheel bearing assembly.

DO NOT attempt to repair hub and wheel bearing assembly. Page 1 of 6 HUB & WHEEL BEARINGS (WITH PULSE VACUUM HUBLOCK) DO NOT attempt to repair hub and wheel bearing assembly. Removal DO NOT remove hub lock assembly by prying on hub lock legs. This can crack

More information

Front brakes (FN- 3), servicing

Front brakes (FN- 3), servicing j a t Front brakes (FN- 3), servicing 46-1 Front brakes, servicing Note: Install complete repair kit. After replacing brake pads and before moving vehicle, depress brake pedal several times firmly to properly

More information

S&W Race Cars and Components, Inc.

S&W Race Cars and Components, Inc. S&W Race Cars and Components, Inc. 11 Mennonite Church Road Spring City, PA 19475 TECH & INFORMATION: 610-948-7303 ORDERS: 1-800-523-3353 OFFICE FAX: 610-948-7342 E-Z INFO FAX 610-792-1234 CAUTION!!! -

More information

Verify caster, camber and toe-in are correct before proceeding.

Verify caster, camber and toe-in are correct before proceeding. If rotating the tie rod end 360 degrees changes the toe-in too much, use the rack tie rod to make smaller adjustments. Put the tie rod end in the steering arm and snug the castle nut before adjusting.

More information

GTI VR6 Front Wheel Bearing DIY http://www.gtishrine.com

GTI VR6 Front Wheel Bearing DIY http://www.gtishrine.com GTI VR6 Front Wheel Bearing DIY http://www.gtishrine.com This procedure covers replacing the front wheel bearings. Tools and Parts required: Wheel Bearing Puller w/ ABS adapter. Available for rent from

More information

BILLET HEADLAMP WITH SHORT/TALL MOUNTS

BILLET HEADLAMP WITH SHORT/TALL MOUNTS -J099 REV. 00-0- BILLET HEADLAMP WITH SHORT/TALL MOUNTS GENERAL Kit Number 9-0, 9-0 Models Kit 9-0 is a -/ inch headlamp and kit 9-0 is a -/ inch headlamp. Both kits will fit the models listed in Table.

More information

TOYOTA TUNDRA 2015 Billet Grille w/led DRL

TOYOTA TUNDRA 2015 Billet Grille w/led DRL TOYOTA TUNDRA 2015 Billet Grille w/led DRL Part Number: 00016-34088 Accessory Code: BG3000 Conflicts Models 1794 and Platinum Kit Contents Item # Quantity Reqd. Description 1 2 LED DRL 2 1 Driver Box 3

More information

Pallet Jack. OWNER S MANUAL Model MH1230. Important Safety Instructions Assembly Instructions Parts and Hardware Identification

Pallet Jack. OWNER S MANUAL Model MH1230. Important Safety Instructions Assembly Instructions Parts and Hardware Identification OWNER S MANUAL Model MH1230 Important Safety Instructions Assembly Instructions Parts and Hardware Identification Pallet Jack CAUTION: Read, understand and follow ALL instructions before using this product

More information

13. REAR WHEEL/BRAKE/SUSPENSION

13. REAR WHEEL/BRAKE/SUSPENSION 13. REAR WHEEL/BRAKE/SUSPENSION 13 3.5~4.5kg-m 8.0~10.0kg-m 0.8~1.2kg-m 3.0~4.0kg-m 2.4~3.0kg-m 3.5~4.5kg-m 6.0~8.0kg-m 13-0 13. REAR WHEEL/BRAKE/SUSPENSION 13 REAR WHEEL/BRAKE/SUSPENSION SERVICE INFORMATION...

More information

FRONT WHEEL ALIGNMENT

FRONT WHEEL ALIGNMENT RONT SUSPNSION RONT WHL LINMNT 67 RONT WHL LINMNT JUSTMNT. INSPCT TIR (S P 67 ) 60H703. MSUR VHICL HIHT Vehicle height: ront Rear C 4W C C 373 0. mm (4.73 in.) 40.5 mm (.59 in.) 4W 0. mm (4.33 in.) 30.5

More information

DYNA RIDER FOOTBOARD KIT

DYNA RIDER FOOTBOARD KIT -J0 REV. 0-0-0 DYNA RIDER FOOTBOARD KIT GENERAL Kit Number 000 Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English

More information

TOYOTA TACOMA 2008- HANDS FREE BLU LOGIC Preparation

TOYOTA TACOMA 2008- HANDS FREE BLU LOGIC Preparation TOYOTA TACOMA 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00112 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:

More information

JK 2.5 Spring Lift Part # 1251000-1251002 # 1351000-1351002 # 1352000-1352002

JK 2.5 Spring Lift Part # 1251000-1251002 # 1351000-1351002 # 1352000-1352002 TeraFlex, Inc. 5241 South Commerce Dr. Murray, Utah 84107 Phone/801.288.2585 Fax/801.713.2313 www.teraflex.biz Rev. 2 December 2010 TT PRODUCT INSTALLATION GUIDE JK 2.5 Spring Lift Part # 1251000-1251002

More information

FRONT WHEEL ALIGNMENT

FRONT WHEEL ALIGNMENT 66 RONT SUSPNSION DJUSTMNT. INSPCT TIR (S P 8) 60I50 ront: Rear:. MSUR VHICL HIHT Vehicle height: ront ( ) Rear (D C) 95 mm (3.74 in.) 6 mm (.44 in.) Measuring points: : round clearance of front wheel

More information

AXLE SHAFTS - FRONT. 1998 Pontiac Bonneville MODEL IDENTIFICATION DESCRIPTION & OPERATION TROUBLE SHOOTING REMOVAL & INSTALLATION

AXLE SHAFTS - FRONT. 1998 Pontiac Bonneville MODEL IDENTIFICATION DESCRIPTION & OPERATION TROUBLE SHOOTING REMOVAL & INSTALLATION AXLE SHAFTS - FRONT 1998 Pontiac Bonneville 1998-99 DRIVE AXLES FWD Axle Shafts - Cars - "C", "G" & "H" Bodies GM Aurora, Bonneville, Eighty Eight, LeSabre, LSS, Park Avenue, Regency, Riviera MODEL IDENTIFICATION

More information

FRONT TURN SIGNAL RELOCATION KIT

FRONT TURN SIGNAL RELOCATION KIT -J0 REV. 00-0-0 FRONT TURN SIGNAL RELOCATION KIT GENERAL Kit Number -0 Models This kit fits 00 and later Dyna model motorcycles (except FXDSE), relocating the front turn signal from the handlebars to the

More information

Little British Car Co.

Little British Car Co. Little British Car Co. 29311 Aranel, Farmington Hills, MI 48334-2815, USA Tel: 248 489 0022 or 800 637 9640 Fax: 248 489 9665 On the web at: www.lbcarco.com E-mail: LBCarco@LBCarCo.com MGB Tube Rear Shock

More information

R O A D M A S T E R, I N C.

R O A D M A S T E R, I N C. R O A D M A S T E R, I N C. 6 28 1 2 "ā 1 2 " 4 8 ITEM QTY NAME PART # 1...4...1/2 x 1 1/4 BOLTS... 350094-00 2...4...1/2 LOCK WASHER... 350309-00 3...4...1/2 HEX NUT... 350258-00 4...2...SPACER PLATE...

More information

AM/FM ANTENNA RELOCATION KIT

AM/FM ANTENNA RELOCATION KIT -J0 REV. 008-09-0 AM/FM ANTENNA RELOCATION KIT GENERAL Kit Number 766-09 Models This kit is used to relocate a fender-mounted AM/FM antenna to a Detachable Tour-Pak on specific model motorcycles. For model

More information

SERVICE PARTS LIST PAGE 1 OF 6 BASE ASSEMBLY SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 12" DUAL BEVEL COMPOUND MITER SAW B27A

SERVICE PARTS LIST PAGE 1 OF 6 BASE ASSEMBLY SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 12 DUAL BEVEL COMPOUND MITER SAW B27A PAGE 1 OF 6 BASE ASSEMBLY 00 0 EXAMPLE: Component Parts (Small #) Are Included When Ordering The Assembly (Large #). SPECIFY CATALOG NO. AND NO. WHEN ORDERING PARTS 1 02-80-0050 Thrust Bearing (1) 2 05-80-0510

More information

92-00 Civic/ 94-01 Integra/ 93-97 Del Sol/ 92-95 CRX Rear Kit Part No. 75540

92-00 Civic/ 94-01 Integra/ 93-97 Del Sol/ 92-95 CRX Rear Kit Part No. 75540 92-00 Civic/ 94-01 Integra/ 93-97 Del Sol/ 92-95 CRX Rear Kit Part No. 75540 www.airliftperformance.com MN-514 (06409) NPR 4762 Please read these instructions completely before proceeding with installation

More information

LG G5 Chassis Brace Gen 5 Camaro THE MOST POWERFUL HEADERS ON THE PLANET Brought to you by LG Motorsports 972-429-1963

LG G5 Chassis Brace Gen 5 Camaro THE MOST POWERFUL HEADERS ON THE PLANET Brought to you by LG Motorsports 972-429-1963 LG G5 Chassis Brace Gen 5 Camaro THE MOST POWERFUL HEADERS ON THE PLANET Brought to you by LG Motorsports 972-429-1963 Thank you for purchasing LG Motorsports products for your Gen 5 Camaro. Parts Inventory:

More information

Section A. GENERAL INFORMATION

Section A. GENERAL INFORMATION Section A. GENERAL INFORMATION I. Description The information and instructions for attaching the sidecar to the right-hand side of the motorcycle are contained in this handbook and must be carefully observed.

More information

Front axle components, overview

Front axle components, overview just a test. Front axle components, overview 40-1 General Information Load bearing components and parts of the suspension must not be welded or straightened. Vehicles without drive axle must not be moved,

More information

specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1967-72 CHEVROLET PICKUP

specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1967-72 CHEVROLET PICKUP specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1967-72 CHEVROLET PICKUP CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect

More information

TABLE OF CONTENTS. I. TROUBLESHOOTING... 2 - Section 1.01: Common Problems/Solutions... 2

TABLE OF CONTENTS. I. TROUBLESHOOTING... 2 - Section 1.01: Common Problems/Solutions... 2 BAL Accu-Slide System I. Table of Contents TABLE OF CONTENTS I. TROUBLESHOOTING... 2 - Section 1.01: Common Problems/Solutions... 2 II. GETTING STARTED... 5 - Section 2.01: Tools You Will Need... 5 - Section

More information

Thank You For Choosing. INSTALLATION INSTRUCTIONS Portal Gear Hubs Polaris RZR 800. (installation performed on 60 Model) (Right) (Left)

Thank You For Choosing. INSTALLATION INSTRUCTIONS Portal Gear Hubs Polaris RZR 800. (installation performed on 60 Model) (Right) (Left) 740B Clifty Drive Madison, Indiana 47250 812-574-7777 INSTALLATION INSTRUCTIONS Portal Gear Hubs Polaris RZR 800 A (installation performed on 60 Model) Item Description Qty A Rotor 4 B Gear Box, L 2 C

More information

Rollator Cane and Brake Replacement SAFETY SUMMARY (CONTINUED)

Rollator Cane and Brake Replacement SAFETY SUMMARY (CONTINUED) Rollator Cane and Replacement Assembly, Installation and Operating Instructions SAVE THESE INSTRUCTIONS NOTE: Check ALL parts for shipping damage. If shipping damage is noted, DO NOT use. Contact Carrier/Dealer

More information

CAM-03, Camshaft Assembly Oil Seal Replacement

CAM-03, Camshaft Assembly Oil Seal Replacement CAM-03, Camshaft Assembly Oil Seal Replacement Tools Jack stands Floor Jack Metric Socket set Metric Wrench set Porsche Timing Belt Tension tool (P9201) Flywheel Lock (P9206) Balance Shaft Pin Spanner

More information

Tooling List 17mm Socket 17mm Wrench 24mm Wrench 26mm Wrench 3/8 Drive Ratchet Torque Wrench

Tooling List 17mm Socket 17mm Wrench 24mm Wrench 26mm Wrench 3/8 Drive Ratchet Torque Wrench Thank you for purchasing the CorkSport Rear Adjustable Camber Arms. By replacing your OEM camber arms with the CorkSport Adjustable Camber Arms, you will be able to dial in your suspension with +/- 5 degrees

More information

1000-LB. TRAILER JACK OWNER S MANUAL

1000-LB. TRAILER JACK OWNER S MANUAL 1000-LB. TRAILER JACK OWNER S MANUAL WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious

More information

BILLET HEADLAMP SHELL

BILLET HEADLAMP SHELL -J008 REV. 007-07- BILLET HEADLAMP SHELL GENERAL Kit Number 770-0 Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section of www.harleydavidson.com

More information

SB-C-CTS/10TW3 SKU# 94552 2008 & Up Cadillac CTS/CTS-V

SB-C-CTS/10TW3 SKU# 94552 2008 & Up Cadillac CTS/CTS-V INSTALLATION GUIDE for the SB-C-CTS/10TW3 SKU# 94552 2008 & Up Cadillac CTS/CTS-V If you choose to perform the installation yourself, it is absolutely vital that the Stealthbox be properly mounted to the

More information

R O A D M A S T E R, I N C.

R O A D M A S T E R, I N C. R O A D M A S T E R, I N C. MOUNTING BRACKET KIT 14 8 7 4 13 5 6 ITEM QTY NAME MATERIAL 1...6...1/2" x 2 1/2" BOLT... 350099-00 2...2...1/2" x 1 1/2" BOLT... 350095-00 3...8...1/2" LOCK WASHER... 350309-00

More information

Slide the new steering column shaft through the steering column from the driver compartment.

Slide the new steering column shaft through the steering column from the driver compartment. Slide the new steering column shaft through the steering column from the driver compartment. Push the column shaft through the steering column until the machined end is out past the column lower bushing.

More information

Char-Lynn Hydraulic Motor. Repair Information. 10 000 Series. October, 1997

Char-Lynn Hydraulic Motor. Repair Information. 10 000 Series. October, 1997 Char-Lynn Hydraulic Motor October, 1997 Repair Information Geroler Motor Two Speed 001 27 Retainer inside bore of valve plate bearingless motors only 4 15 16 3 6 35 Parts Drawing 25 2 2 1 19 17 36 40 47

More information

Installation manual. 4 suspension system. 2014-2016 Chevy or GMC 1500 4WD. Part # 14059. Part # 14059. Important customer information:

Installation manual. 4 suspension system. 2014-2016 Chevy or GMC 1500 4WD. Part # 14059. Part # 14059. Important customer information: Installation manual 4 suspension system 2014-2016 Chevy or GMC 1500 4WD Part # 14059 sj09052013rev.01 Part # 14059 2014-2016 Chevy or GMC 1500 4WD 4 suspension system Part # Description Qty. 14056-01 Upper

More information

Recall R136 Front Lower Ball Joints Check Torque or Replace

Recall R136 Front Lower Ball Joints Check Torque or Replace SERVICE DATE /00 Amended /00 TECHNICAL BULLETIN Recall R6 Front Lower Ball Joints Check Torque or Replace MODEL VIN Remove and destroy Bulletin S04-R6, dated /00. Replace with this Bulletin. Revisions

More information

TJ Quick Disconnect Instructions

TJ Quick Disconnect Instructions 1 TJ Quick Disconnect Instructions www.teraflex.com Kit #17012 Kit #17092 Kit #17010 Kit #17090 Important Notes: Prior to beginning this or any installation read these instructions to familiarize yourself

More information

Installation Guide 2010 BMW S1000RR Full Exhaust System

Installation Guide 2010 BMW S1000RR Full Exhaust System Installation Guide 2010 BMW S1000RR Full Exhaust System!! THIS PRODUCT IS DESIGNED FOR USE IN CLOSED COURSE RACING AND IS NOT INTENDED FOR HIGHWAY USE!! Congratulations on the purchase of your new TaylorMade

More information

Installation Instructions 4508 4508S

Installation Instructions 4508 4508S SYMPHONY Spread Lavatory Faucet with Speed Connect Drain Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American Standard faucets. Speed Connect

More information

12. REAR WHEEL/BRAKE/SUSPENSION

12. REAR WHEEL/BRAKE/SUSPENSION 12 12 12-0 SERVICE INFORMATION... 12-1 REAR BRAKE... 12-5 TROUBLESHOOTING... 12-2 REAR SHOCK ABSORBER... 12-8 REAR WHEEL... 12-3 REAR FORK... 12-9 SERVICE INFORMATION GENERAL INSTRUCTIONS When installing

More information

R O A D M A S T E R, I N C.

R O A D M A S T E R, I N C. R O A D M A S T E R, I N C. ROADMASTER, Inc. 6110 NE 127th Ave. Vancouver, WA 98682 6 13 11 MOUNTING BRACKET KIT Cable Tab 14 12 7 15 9 Cable Tab 360-896-0407 fax 360-735-9300 www.roadmasterinc.com ITEM

More information

Depending on which elastic support you have you can secure the V2 power unit to the following seat bracket tubes: EXTERNAL DIAMETER 27.

Depending on which elastic support you have you can secure the V2 power unit to the following seat bracket tubes: EXTERNAL DIAMETER 27. ASSEMBLY 1 - EPS V2 POWER UNIT (SOLUTION 5) 1.1 - POSITIONING INSIDE THE SEAT TUBE WITH ELASTIC SUPPORT IN THE SEAT BRACKET TUBE Depending on which elastic support you have you can secure the V2 power

More information

http://localhost/vida/jsp/information/xml/xmldocprintpreview.jsp

http://localhost/vida/jsp/information/xml/xmldocprintpreview.jsp Page 1 of 7 60: Wheel alignment V70 XC (01-) / XC70 (-07), 2001, B5244T3, AW50/51 AWD, L.H.D, YV1SZ58D811036138, 036138 5/4/2014 PRINT 60: Wheel alignment Wheel alignment, checking / adjusting Note! For

More information

TABLE OF CONTENTS. Section 1 - Assembling your new pit bike.

TABLE OF CONTENTS. Section 1 - Assembling your new pit bike. Orion Pit Bike Sales Owners Manual (All information and content is the property of Orion Pit Bike Sales. Any attempt to copy or resell is a direct violation of our copyright. All violators will be prosecuted)

More information

R O A D M A S T E R, I N C.

R O A D M A S T E R, I N C. R O A D M A S T E R, I N C. ROADMASTER, Inc. 6110 NE 127th Ave. Vancouver, WA 98682 12 10 3 11 4 5 13 7 8 360-896-0407 fax 360-735-9300 www.roadmasterinc.com ITEM QTY NAME MATERIAL 1... 4...1/2 x 1 1/2

More information

DLC:GH B6CJ6A HJEEA:B:CI

DLC:GH B6CJ6A HJEEA:B:CI SERIES 2 S E RI E S 2 DLC:GH B6CJ6A HJEEA:B:CI SERIAL NUMBER Z2SUPP_0211Rev B - READ THIS MANUAL DO NOT OPERATE THIS WHEELCHAIR WITHOUT FIRST READING AND UNDERSTANDING THIS TiLITE OWNERS MANUAL SUPPLEMENT.

More information

K3089B/K3089BMX 55717B/55717BMX 2007-2013 Jeep Wrangler JK 4WD 2 Door & 4 Door Stage 1 4 Lift Kit

K3089B/K3089BMX 55717B/55717BMX 2007-2013 Jeep Wrangler JK 4WD 2 Door & 4 Door Stage 1 4 Lift Kit 400 W. Artesia Blvd. Compton, CA 90220 Fax: (310) 747-3912 Ph: 1-800-776-0767 E-Mail: info@procompusa.com Website: www.procompusa.com Latest Revision: PRO COMP SUSPENSION K3086B/K3086BMX 2007-2013 Jeep

More information

Char-Lynn Spool Valve Hydraulic Motors. Repair Information. W Series Geroler Motors

Char-Lynn Spool Valve Hydraulic Motors. Repair Information. W Series Geroler Motors Char-Lynn Spool Valve Hydraulic Motors Repair Information W Series Geroler Motors with Parking Brake 004 Nut Key Ring, Retaining Bearing Ring, Retaining Ring, Retaining Washer (Thick), Pressure Washer,

More information

R O A D M A S T E R, I N C.

R O A D M A S T E R, I N C. R O A D M A S T E R, I N C. 11 10 20 12 4 18 19 1 2 13 16 ITEM QTY NAME MATERIAL 1...2... 1/2" x 3 1/2" BOLT... 350103-00 2...2... 1/2" x 2" BOLT... 350097-00 3...6... 1/2" x 1 1/2" BOLT... 350095-00 4...2...

More information

Round Housing with Side Ports

Round Housing with Side Ports Power Steering Steering Control Unit (SCU) Parts and Repair Information 5 Series Steering Control Units 001 Square Housing with Side Ports Round Housing with Side Ports T E L RP Round Housing with End

More information

Volkswagen Phaeton 44-2 Wheel and tire mounting Wheel mounting Mounting tires Pressing off tires Dismounting tires Mounting tires

Volkswagen Phaeton 44-2 Wheel and tire mounting Wheel mounting Mounting tires Pressing off tires Dismounting tires Mounting tires Wheel and tire mounting Стр. 1 из 1 Volkswagen Phaeton 44-2 Wheel and tire mounting Wheel mounting Wheel bolt to hub Torque specification: 120 Nm Mounting tires The tires are installed as usual, but note

More information