SOLENOID VALVES INDEX VALVES GENERAL CATALOG SERIES

Transcription

1 resenting our CD drawing data catalog VLVES GENEL CTLOG SOLENOID VLVES SEIES INDEX Characteristics 98 Basic Models and Configuration Series Specifications 102 Solenoid Valve Order Code 10 Manifold Order Code 105 Operating rinciple, Major arts and Materials 106 Dimensions of Solenoid Valve 107 Dimensions of Manifold 110 Handling Instructions and recautions 115 C Board Manifold 00 Series Specifications 118 Order Code 119 Dimensions 120 Made to Order 122 Handling Instructions and recautions

2 OWEFUL & LOW OWE CONSUMTION SOLENOID VLVES The solenoid valve 00 series achieves its highly reliable, powerful and low current basic performance into a thin body with valve width of 10mm. These reliable 2-, 3-, 5-port pilot type solenoid valve has features of flywheel diodes for surge suppression as standard equipment. Moreover, the 00 series line-up features detailed improvements in utility, including an J type manifold that offers excellent ease of assembly and maintenance, a twin solenoid whose length, wiring, and piping are the same as the single solenoid while maintaining functions of a double solenoid, and a C board manifold containing a print circuit board with connector. SOLENOID VLVES 00 SEIES SEIES ilot type solenoid valve 2-, 3-, 5-port Effective area 1.5mm 2 ower consumption 0.7W Optimum for operation of 625 double acting and single acting cylinders, pilot-operated valves and actuators, etc. 98

3 C BOD MNIFOLD 00 SEIES ilot type solenoid valve 2-, 3-, 5-port Effective area 1.5 ower consumption 0.7W Only available for 8 stations and 16 stations. SOLENOID VLVES 00 SEIES TWIN SOLENOID VLVES 00 SEIES New space-saving type valve is installable with the solenoid valve 00 series and the 00 series C board manifold. etains the basic performance and functions of a double solenoid while also achieving the piping and wiring configuration of a single solenoid. ilot type solenoid valve 5-port Effective area 1.5 ower consumption 0.7W 99

4 Basic Models and Configuration of 00 Series Single unit ilot type solenoid valve 00 series 2-, 3-port 5-port, 2-position Normally closed (NC) Normally open (NO) Single solenoid Double solenoid Twin solenoid Direct piping 01E1 Note (00E1 ) 01E1-11 (00E1-11 Note ) 00-E1 00-E2 00-KE2 Note Normally closed (NC) Normally open (NO) Single solenoid Double solenoid Sub-base piping 01E E E E2-25 Note: The 00E1, 00E1, and 00-KE2, 00-KE2 are for manifolds for combined mounting of 2-, 3-, 5-port valves. They cannot be used as a single unit. When using 2-, 3-port valves as a single unit, please use 01E1, 01E

5 Manifold 00 series Small sized manifold for 2-, 3-port valve 01MF F type (, ) manifold 01E1 01E M type (all port) manifold 01E1 01E MJ J type (all port, with quick fitting) manifold 01E1 01E1-11 quick fitting SOLENOID VLVES 00 SEIES 00MF F type (, ) manifold 00-E2 00-E1 00M type (all port) manifold 00-E2 00-E1 00MJ J type (all port, with quick fitting) manifold 00-E2 00-E1 00E1, 00E , 3-port valve for manifold only 00E1, 00E , 3-port valve for manifold only 00E1,00E , 3-port valve for manifold only Manifold for combined mounting for 2-, 3-, 5-port valve C board manifold Note 35 () 1 () 00MF F type (, ) manifold 00E1, 00E , 3-port valve for manifold only 00-E1 00-E2 35 () 1 () 35 () 1 () () 2 (B) 00M type (all port) manifold 00E1, 00E , 3-port valve for manifold only 00-E1 00-E2 35 () 1 () () 2 (B) 35 () 1 () 2 (B) () Twin solenoid valve 00MF F type (, ) manifold 00E1,00E , 3-port valve for manifold only 00-E1 00-KE2 Twin solenoid valve for manifold only 35 () 1 () 00M type (all port) manifold 00E1,00E , 3-port valve for manifold only 00-KE2 Twin solenoid valve for manifold only 35 () 1 () () 2 (B) 00MJ J type (all port, with quick fitting) manifold 00E1, 00E , 3-port valve for manifold only 00-E1 00-KE2 Twin solenoid valve for manifold only 35 () 1 () () 2 (B) Note: Only available for 8 stations or 16 stations. 101

6 SOLENOID VLVES 00 SEIES Basic Models and Valve Functions Basic model Direct piping, F type manifold 01E1 (00E1 Note ) 00-E1 00-E2 00-KE2 Note Cylinder operating speed How to obtain cylinder speed Item Number of positions Number of ports 2, 3 ports 5 ports Valve function Item Media Basic model Operation method ort size Note 2 Shock resistance m/s 2 {G} {10.0} (axial direction 25.0 {25.0}) Operating voltage range Wiring Note Color of lead wire Standard Option DC V Current m (ower consumption when rated voltage is applied: W) Surge suppression (as standard).55.5 (510%) 120 (0.6) With LED indicator 121 (0.6) Green (+) Black ( ) (610%) 105 (0.6) With LED indicator 106 (0.6) Blue (+) Black ( ) Grommet type lug connector type Flywheel diode (1210%) 55 (0.7) With LED indicator 56 (0.7) Brown (+) Black ( ) (210%) 28 (0.7) With LED indicator 29 (0.7) Maximum allowable leakage current m Insulation resistance MΩ Min. 100 Lead wire length Note Color of LED indicator Sub-base piping,, J type manifold Direct piping, F type manifold Sub-base piping,, J type manifold Max. 12/18 Max. 12/18 With built-in flywheel diode for surge suppression 300mm ed M30.5 Operating pressure range Ma {kgf/cm 2 } {2.07.1} esponse time Note 3 DC5V, DC12V ON/OFF ms DC6V, DC2V 01E1 (00E1 Note ) Normally closed (NC, standard) or Normally open (NO, option) Single solenoid 2 positions Double solenoid Minimum time to energize for self holding ms Twin solenoid emark: For optional specifications and order code, see p Note: The 00E1, 00E1, and 00-KE2, 00-KE2 are manifolds for combined mounting of 2-, 3-, 5- port valves. They cannot be used as a single unit. When using 2-, 3-port valves as a single unit, please use 01E1, 01E1-25. Specifications Notes: 1. For details, see the effective area on p For details, see the port size on p Values when air pressure is 0.5Ma {5.1kgf/cm 2 }. Values of 00-E2 and 00-KE2 are switching from the opposite position. emark: Conversion to psi., 1Ma=15psi., 1kgf/cm 2 =1.2psi., e.g. 0.2Ma=29psi. Note: See made to order on p E1 Effective areacv Note 1 mm Lubrication ir 00-E2 Internal pilot type Not required roof pressure Ma {kgf/cm 2 } 1.05 {10.7} Maximum operating frequency Hz 5 Operating temperature rangeatmosphere and media Mounting direction Solenoid Specifications Item ated voltage C 01E1 (00E1) 01E1 (00E1) 00-E1 00-E1 550 ny 00-E2 00-E2 00-KE2 Note 00-KE2 00-KE2 Max. 12 Max. 12 DC 5V DC 6V DC 12V DC 2V ed (+) Black ( ) Cylinder stroke Solenoid valve energized To obtain the time required for the cylinder to complete 1 stroke, add cylinder's delay time, t1 (time between energizing of solenoid valve and actual starting of cylinder), to the cylinder s max. operating time, t2. When a cushion is used, add the cushioning time, t3, to the above calculation. Standard cushioning time t3 is approximately 0.2 seconds. 00-E1 Measurement conditions ir pressure: 0.5Ma {5.1kgf/cm 2 } iping inner diameter and length: mm Fitting: Barb fitting BFBU-M3 Load Load ratio = (%) Cylinder theoretical thrust Cylinder stroke: 60mm (10, 16) 100 mm (20 32) Load Maximum operating speed Maximum operating speed Delay time Delay time S t1 t2 t3 Cylinder start Cushioning impact Cylinder stop Solenoid valve 00-E1 0.5Ma Time Fitting BFBU-M3 Load ratio Load ratio % 102

7 Flow ate Effective reacv mm 2 Ma Valve outlet pressure Supply pressure (Ma) Flow rate /min(n) 01E1 (00E1) 00-E1 00-E2 00-KE2 01E1 (00E1) 00-E1 00-E2 00-KE2 How to read the graph If supply pressure is 0.5Ma and flow is 75/min (N), the valve outlet pressure becomes 0. Ma. Basic model Standard (single valve) emarks 01E1 (00E1) 00-E1 00-E2 00-KE2 01E1 (00E1) 00-E1 00-E2 00-KE2 Basic model ort ort specifications ort size 01E1 (00E1 Note ) 00-E1 00-E2 00-KE Solenoid Valve ort Size 01E E E2-25,,,, B,, B When the quick fitting TS3-M3M is installed to,, B ports, the value becomes When the quick fitting TS3-M3M is installed to,, B ports on F type manifold, the value becomes When the quick fitting TS-M5M is installed to,, B ports on type manifold, the value becomes Female thread Female thread Female thread M30.5 M30.5 M50.8 Note: 00E1 is dedicated valve for manifold. Cannot be connected to the port with fitting. SOLENOID VLVES 00 SEIES Manifold Connection ort Size Manifold model ort Location of piping connection ort size 01MF 00MF 01M 00M 01MJ 00MJ, B, B, B Manifold Valve Manifold Manifold Manifold M50.8 M30.5 c1/8 c1/8 M50.8 c1/8 (Common for, ) c1/8 Quick fitting for c1/8 (Common for, ) Valve Mass Basic model 01E1 (00E1) 00-E1 00-E2 00-KE2 01E1 (00E1) 00-E1 00-E2 00-KE2 Mass (38) (5) 37 (60) 5 emark: Figures in parentheses ( ) are the mass with sub-base: -25. g Manifold Mass Manifold model 01MF 01M 01MJ 00MF 00M 00MJ Mass calculation of each unit n=number of units Block-off plate g 103

8 00 Series Solenoid Valve Order Code 2-, 3-port valve Number of valves 3-port 2-, 3-port valve Valve function Normally closed NC Mounting base Without mounting base Sub-base Without sub-base Muffler Without muffler Wiring Grommet type Blank Blank Blank Blank Blank Blank 2-port Normally open NO With mounting base With sub-base With muffler for direct piping Straight connector with LED indicator SL ttached to valve body at time of delivery. ttached to valve body at time of delivery. With muffler for sub-base piping L connector with LED indicator -75 -LL Basic model Voltage Direct piping 2-, 3-port 5-port single solenoid 5-port double solenoid 01E1 00-E1 00-E SL -LL DC5V DC6V DC12V DC2V Sub-base piping 2-, 3-port 5-port single solenoid 5-port double solenoid 01E1 00-E1 00-E SL -LL DC5V DC6V DC12V DC2V For manifold for combined mounting of 2-, 3-, 5-port valves Note 2-, 3-port for 00MF 5-port twin solenoid for 00MF 2-, 3-port for 00M, J 5-port twin solenoid for 00M, J Note: Cannot be used as a single unit. 00E1 00-KE2 00E1 00-KE SL -LL DC5V DC6V DC12V DC2V The muffler for direct piping is M30.5, cannot be used for subbase piping. The muffler for sub-base piping is M50.8, cannot be used for direct dditional arts (Sold Separately) Muffler Block-off plate For direct piping 10 KM-03 KM-05 For sub-base piping 00 M F -B F For F type manifold For, J type manifold 01 For 01M 00 For 00M

9 00 Series Manifold Order Code 2-, 3-port valve Number of valves 3-port 2-, 3-port valve Valve function Normally closed NC Wiring Grommet type Blank Blank Blank 2-port Normally open NO Straight connector with LED indicator SL L connector with LED indicator -LL SOLENOID VLVES 00 SEIES Manifold model Number of units Station Basic model Voltage Small sized manifold for 2-, 3-port valve 01M 2 20 F J stn. stn. -01E1-01E SL -LL DC5V DC6V DC12V DC2V Manifold for combined mounting of 2-, 3-, 5-port valve 00M 2 20 F J stn. stn. stn. stn. -00E1-00-E1-00-E2-00-KE2-00E1-00-E1-00-E2-00-KE SL -LL -SL -LL DC5V DC6V DC12V DC2V DC5V DC6V DC12V DC2V Valve mounting location from the left-hand side when facing, B port (1 20) Since twin solenoid valve needs two stations per valve to mount, the second station (solenoid S1 side) should be blank. Made to Order Lead wire length Grommet type with LED indicator Locking type manual override Specify the valve type for each station. -B 00-KE2-1L -3L For plug connector Length -1L: 1000 (mm) -3L: L

10 Operating rinciple, Major arts and Materials 3-port Normally closed (NC) Normally open (NO) Solenoid 01E1 De-energized Solenoid cover Column 01E1-11 De-energized lunger Flapper Manual override ilot valve body Body Lip seal End cover lunger spring lunger pin iston Stem Major arts and Materials Valve Manifold arts Body Stem Lip seal Mounting base Sub-base lunger Column Body Block-off plate Seal Materials luminum alloy (anodized) Synthetic rubber Steel (zinc plated) luminum alloy (anodized) Magnetic stainless luminum alloy (anodized) Steel (nickel plated) Synthetic rubber 5-port Single solenoid Double solenoid 1S2 Solenoid 2B E1 00-E2 Solenoid cover Column lunger 2B (De-energized condition after energizing of solenoid S1) 1S S1 00-KE2 (De-energized condition after energizing of solenoid S1) 1S2 12S1 Flapper Manual override ilot valve body Body 2B 1 32 lunger spring lunger pin iston 51 2B B Lip seal End cover Stem 2 106

11 Dimensions of Solenoid Valve for 2-, 3-port (Scale 3/, Unit mm) 01E E1 Manual override 3-M Mounting hole E Counter bore 3.2 Depth 1 Mounting hole E E1 SOLENOID VLVES 00 SEIES Manual override M Mounting hole 29.5 Options Made to Order Muffler: -75 For direct piping Order code for sold separately: KM MUFF Mounting base: To the top of the valve 1.2 Locking type manual override: -81 M30.5 For sub-base piping Order code for sold separately: KM Mounting hole M50.8 For wiring options and made to order, see p

12 17 Manual override Dimensions of Solenoid Valve 5-port, 2-position (Scale 3/, Unit mm) 00-E1 00-E1 Manual override 5-M Mounting hole Counter bore 3.2 Depth 1 Mounting hole 00-E E B 5-M Mounting hole Options Made to Order Muffler: -75 For direct piping Order code for sold separately: KM MUFF Mounting base: To the top of the valve 1.2 Locking type manual override: -81 M30.5 For sub-base piping Order code for sold separately: KM Mounting hole M50.8 8

13 Manual override Dimensions of Solenoid Valve 5-port, 2-position (Scale 3/, Unit mm) 00-E2 00-E Manual override 5-M Mounting hole E2-25 2B Counter bore 3.2 Depth 1 Mounting hole E2 SOLENOID VLVES 00 SEIES B M Mounting hole Options 00SOL Made to Order 00SOL Solenoid with straight connector: -SL 10 2 Solenoid with L connector: -LL Grommet type with LED indicator: -L Total length of valve 27.5 LED indicator B Total length of valve 21.5 LED indicator C Total length of valve LED indicator Model Code B C (Lead wire length) emarks 01E1,01E E1,00-KE2 00-E1-25,00-KE2 00-E2,00-E SL,-LL,-L: 300 (standard length) Made to order -1L: 1000, -3L: 3000 Length to the end of the valve or sub-base Total length to the end of the opposite side solenoid 109

14 Dimensions of Manifold for 2-, 3-port (Scale 3/, Unit mm) 01MF L Manual override Mounting hole 2-c1/8 With 1 plug 13.3 M stn.1 stn.2 stn.3 stn. stn L Manual override c1/8 With 2 plugs M50.8 With 1 plug 01E1, 01E1-11 Block-off plate -B Unit dimensions Model L Model L 01M2F M12F F F F F F F F F F F F F F F F F F M 01M 3.9 stn.1 stn.2 stn.3 stn. stn Mounting hole E1, 01E M For wiring options and made to order, see p. 11. Block-off plate -B Unit dimensions Model L Model L 01M M

15 Dimensions of Manifold for 2-, 3-port (Scale 3/, Unit mm) 01MJ 01MJ L Manual override Mounting hole -c1/8 With 2 plugs Quick fitting stn.1 stn.2 stn.3 stn. stn.5 01E1, 01E1-11 Block-off plate -B MJ Unit dimensions Model L Model L 01M2J M12J J J J J J J J J J J J J J J J J J SOLENOID VLVES 00 SEIES For wiring options and made to order, see p

16 L Manual override Mounting hole c1/8 With 1 plug M50.8 With 1 plug Mounting hole Dimensions of Manifold for Combined Mounting of 2-, 3-, 5-port Valves (Scale 3/, Unit mm) 00MF 00MF B 2B 2B M E1 00E1, 00E E Block-off plate -B stn.1 stn.2 stn.3 stn. stn.5 Example of twin solenoid valve combined mounting 112 For wiring options and made to order, see p. 11. Unit dimensions Model L Model L 00M2F M12F F F F F F F F F F F F F F F F F F

17 L Manual override Mounting hole c1/ Dimensions of Manifold for Combined Mounting of 2-, 3-, 5-port Valves (Scale 3/, Unit mm) 00M 00M With 2 plugs SOLENOID VLVES 00 SEIES 00-E1 1 00E1,00E E2 36 lug to B for mounting 00E1 lug to for mounting 00E1-11 Block-off plate -B 2-M50.8for each unit 2B M stn.1 stn.2 stn.3 stn. stn.5 Example of twin solenoid valve combined mounting L Mounting hole For wiring options and made to order, see p. 11. Unit dimensions Model L Model L 00M M

18 L Manual override Mounting hole 13 -c1/8 11 With 2 plugs Dimensions of Manifold for 5-port, 2-position (Scale 3/, Unit mm) 00MJ 00MJ E1 00E1, 00E Quick fittingfor each unit lug to B for mounting 00E1 lug to for mounting 00E E2 Block-off plate 00M2J M12J B 3J J J J J J J J B 7J J J J J J J J J Unit dimensions Model L Model L stn.1 stn.2 stn.3 stn. stn.5 Combined mounting of twin solenoid valve is acceptable. See p Options 00SOL Made to Order 00SOL Solenoid with straight connector: -SL Solenoid with L connector: -LL Grommet type with LED indicator: -L Total length of valve 27.5 LED indicator B Total length of valve 21.5 LED indicator C Total length of valve LED indicator Model 01E1, 01E1 00E1, 00E1, 00-E1, 00-E1,00-KE2, 00-KE2 00-E2, 00-E2 11 Code B C Lead wire length) emarks SL, -LL, -L: 300 (standard length) Made to order -1L: 1000, -3L: 3000 Length to the end of the valve Total length to the end of the opposite side solenoid

19 Handling Instructions and recautions Solenoid lug connector Manual override Internal circuit ttaching and removing plug connector Non-lock type DC5V, DC6V, DC12V, DC2V Standard solenoid (surge suppression) Lead wire DC5V Green Short circuit protection diode DC6V Blue DC12VBrown DC2Ved Solenoid Flywheel diode Lead wire: Black Solenoid with LED indicator (surge suppression) Order code-sl, -LL Lead wire DC5V Green DC6V Blue DC12VBrown DC2Ved LED indicator Light emitting diode Use fingers to insert the connector into the pin, push in until the lever claw catches on the convex section on the connector housing, and complete the connection. To remove the connector, squeeze the lever along with the connector, lift the lever claw up from the convex section on the connector housing, and pull out. Convex section in Connector housing Lever Indication of polarity DC Connector Contact Connector assembly To operate, press the manual override all the way down. The valve works the same as an energized state as long as the manual override is pushed down, and returns to the rest position upon release. In the double solenoid and twin solenoid, pressing the manual override on the S1 (S2) side switches the state of the S1 (S2) to energized state, and the unit remains in that state even after the manual override is released. To return to the rest position, operate the manual override on the S2 (S1) side. SOLENOID VLVES 00 SEIES Lead wire: Black LED indicator: ed Illustration shows the110 series. C The C board manifold is DC2V only. Crimping of connecting lead wire and contact Cautions: 1. Do not apply megger between the lead wires. 2. While there is no danger with a DC solenoid of a short circuit due to the wrong polarity, the valve will not operate. 3. Leakage current inside the circuit could result in failure of the solenoid valve to return or in other erratic operation. lways use within the range of the allowable leakage current. If circuit conditions, etc., cause the leakage current to exceed the maximum allowable leakage current, consult us.. For double solenoid and twin solenoid, avoid energizing both solenoids simultaneously. The valve could fall into a neutral state. To crimp lead wires into contacts, strip off mm of the insulation from the tip of the lead wire, insert into the contact, and crimp it. Be sure at this time to avoid catching the insulation on the wire as crimping section. Contact Hook Expose wire crimping section Expose wire mm Lead wire Equivalent to WG2226 Insulation crimp tab InsulationMaximum outer diameter1.7 Cautions: 1. Do not pull hard on the lead wire. 2. lways use the dedicated tool for crimping of connecting lead wire and contact. Contact: Model M Manufactured by Sumiko Tech, Inc. Crimping tool: Model F Manufactured by Sumiko Tech, Inc. Lock type To lock the manual override, use a small screwdriver to push down on the manual override all the way down and turn it clockwise 5 degrees. When locked, turning the manual override 5 degrees in a counterclockwise direction returns it to its original position, and releases the lock. ttaching and removing contact and connector Insert the contact with lead wire into a plug connector hole until the contact hook catches and is secured to the plug connector. Confirm that the lead wire cannot be easily pulled out. To remove, insert a tool with a fine tip (such as a small screwdriver) into the rectangular hole on the side of the plug connector to push up on the hook, and then pull out the lead wire. Illustration shows the 20 series. Cautions: 1. The 00 series are pilot type solenoid valves. s the result, the manual override cannot switch the main valve without supplying air from the port. 2. lways release the lock on the locking type before commencing normal operation. 3. Do not attempt to operate the manual override with a pin or other object having an extremely fine tip. It could damage the manual override button. Cautions: 1. Do not pull hard on the lead wire. It could result in defective contacts, breaking wires, etc. 2. If the pin is bent, use a small screwdriver, etc., to gently straighten out the pin, and then complete the connection to the plug connector. 115

20 Fitting ecommended fittings 01E1 arts ort port, port Note 1 port Note 2 port Quick fitting TS3-M3M TL3-M3M TLL3-M3M TS3-M3M TL3-M3M TLL3-M3M TS3-M3M TC fitting For urethane tube For nylon tube BFBU-M3 BF3BU-M3 BF-M3 BF3.2-M3 BFBU-M3 BF3BU-M3 BF-M3 BF3.2-M3 BFBU-M3 BF3BU-M3 BF-M3 BF3.2-M3 Muffler KM E1, 00-E2, 00-KE2 arts ort, B port, port Note 1 port Note 2 port Quick fitting TS3-M3M TS3-M3M TL3-M3M TLL3-M3M TS3-M3M TC fitting For urethane tube For nylon tube BFBU-M3 BF3BU-M3 BF-M3 BF3.2-M3 BFBU-M3 BF3BU-M3 BF-M3 BF3.2-M3 BFBU-M3 BF3BU-M3 BF-M3 BF3.2-M3 KM-03 Notes :1. For piping to the port only, TSH-M3M may also be used. 2. These fittings may be used for mounting a muffler to the port. 01E1-25 arts ort port port, port Quick fitting TS-M50 TS-M5M TSH-M5M TS-M50 TS-M5M TSH-M5M TS-M50 TS-M5M TSH-M5M Muffler Speed controller reference) KM SCE-M5 00-E1-25, 00-E2-25 arts ort, B port port, port Quick fitting TS-M50 TSH-M5 TS-M5M TSH-M5M TS-M50 TSH-M5 TS-M5M TSH-M5M TS-M50 TSH-M5 TS-M5M TSH-M5M Muffler KM

21 117 SOLENOID VLVES 00 SEIES

22 C BOD MNIFOLD 00 SEIES Manifold Basic Models and Specifications Item Basic model Type of mounting valve Manifold function Number of units 2-, 3-port 8 stations 16 stations 5-port, single solenoid 5-port, double solenoid 5-port, twin solenoid, manifold 00M8F 00M16F 00E1 00-E1 00-E2 00-KE2 ll port manifold 00M8 00M16 00E1 00-E1 00-E2 00-KE2 Wiring Connector type for flat cable (WG28) Note 1 : With short clip (standard) With long clip (option) Note 2 Common wiring Operating temperature range (atmosphere and media) C Shock resistance m/s 2 {G} Mounting direction Item Media esponse time Note DC5V, DC12V ms ON/OFF DC6V, DC2V Type Operating voltage range Wiring Basic model Operation method Effective areacv mm 2 Lubrication Operating pressure range Ma {kgf/cm 2 } roof pressure Ma {kgf/cm 2 } Maximum operating frequency Minimum time to energize for self holding Color of lead wire DC V Current (ower consumption when m rated voltage is applied: W) Maximum allowable leakage current m Insulation resistance Color of LED indicator For F type manifold For type manifold MΩ Header Box type, with short clip (roduct number scsc) Box type, with long clip (roduct number: LCSC) Hz ms DC5V 00E1 00E1 With built-in flywheel diode for surge suppression.55.5 (5±10%) 130 (0.7) Min. 100 lug connector type straight connector -SL: With dedicated lead wire for C board connection, with connector ed (+), Black ( ) ed Socket Note Strain relief Note Standard Open end type, with nose (roduct number: SC) lus common (standard) Minus common (option: -CM) Note {25.0} Notes: 1. For details about specifications, see the specifications of connector for flat cable. 2. For order codes, see p Solenoid Valve Specifications ny 00-E1 00-E2 ir Internal pilot type Not required {2.07.1} 1.05 {10.7} Max. 12/15 12 Max. 12 Max. 12/15 12 Max (6±10%) 115 (0.7) (12±10%) 65 (0.8) With attached (roduct number J) 00-KE2 00-E1 00-E2 00-KE2 Note: Values when air pressure is 0.5Ma {5.1kgf/cm 2 }. Values of 00-E2 and 00-KE2 are switching from the opposite position. emark: Conversion to psi., 1Ma=15psi., 1kgf/cm 2 =1.2psi., e.g. 0.2Ma=29psi. Solenoid Specifications Item Order code Blank -LC DC6V DC12V DC2V (2±10%) 0 (1.0) MIL-C conformity (made by Sumitomo 3M Ltd.) emark: While the connector has a center slot (groove), note that it has no key grooves for prevention of erroneous insertion. Note Included at time of delivery. 118 Item ated voltage Specifications of Connector for Flat Cable Flow ate Manifold Connection ort Size Manifold model ort Location of piping connection ort size 00MF 00M Mass Manifold model Ma Valve outlet pressure 00M8F M16F 00M8 00M16 How to read the graph If supply pressure is 0.5Ma and flow rate is 75/min (N), the valve outlet pressure becomes 0. Ma. Manifold Mass , B, B Supply pressure (Ma) E E E2 00-KE E E1 00-E2 00-KE Flow rate /min(n) Manifold Valve Manifold Manifold Mounting valve mass M50.8 M30.5 c1/8 c1/8 M50.8 c1/8 (Common for, ) 00E1 00-E1 00-E2 00-KE2 Block-off plate g

23 C Board Manifold 00 Series Order Code Common wiring Connector 2-, 3-port valve Number of ports 2-, 3-port valve Valve function Wiring lus common With short clip 3-port Normally closed NC Straight connector with LED indicator Blank Blank Blank Blank -SL 2-port Normally open NO -CM -LC SOLENOID VLVES 00 SEIES C board manifold for combined mounting of 2-, 3-, 5-port valve 00M Manifold model Number of units 8 16 F -CM -LC -CM -LC emark: 00E1 is 3-port, and normally closed (NC) as standard. Valve mounting location from the left-hand side when facing, B port (: 1 16) Since twin solenoid valve needs two stations per valve to mount, the second station (solenoid S1 side) should be blank. When selecting 00-E2, always enter -B for the next station. Station stn. stn. stn. stn. Basic model -00E E1-00-E2-00-KE2-00E1-00-E1-00-E2-00-KE SL -SL Specify the valve type for each station. Enter -B when closing a station with a block-off plate without mounting a valve. 00-E2 cannot be mounted to the last station. 00-KE2 cannot be assigned to the last station when ordering. DC5V DC6V DC12V DC2V DC5V DC6V DC12V DC2V dditional arts (Sold Separately) Made to Order For details, see p Block-off plate J type manifold J 00 M F -B F For F type manifold, J type manifold 119

24 Dimensions (Scale 1/2, Unit mm) 00M8F 00M16F D Connector for flat cable With short clip: Standard With long clip: -LC L c1/8 With 1 plug M Mounting hole 11 2-M50.8 With 1 plug 01E1, 01E E1 00-E2 Block-off plate -B Unit dimensions Model L D 00M8F M16F Option dimensions Type Short clip 12.5 Long clip 15.5 Example of twin solenoid valve combined mounting L Mounting hole

25 Dimensions (Scale 1/2, Unit mm) 00M8 00M D Only 16 stations Connector for flat cable With short clip: Standard With long clip: -LC L SOLENOID VLVES 00 SEIES Mounting hole 13 1 c1/8 Both sides 01E1, 01E E1 00-E2 lug to B for mounting 00E1 lug to for mounting 00E1-11 Block-off plate -B Unit dimensions Model L D 00M M B Type Short clip 12.5 Long clip 15.5 Example of twin solenoid valve combined mounting L Mounting hole Option dimensions 121

26 Made to Order variety of made to order items are available to further expansion of the range of applications for the C board manifolds compatible with the solenoid valve 00 series. Order Code 00M J type manifold Voltage Type of mounting valve J Number of units Station J type manifold Specifications The manifold, solenoid valve, and solenoid specifications are the same as the type manifold specifications. See p Manifold Connection ort Size Manifold model 00MJ ort, B Location of piping connection Manifold iping size c1/8 Quick fitting for c1/8 (, common) Manifold Mass Manifold model 00M16J 00 series manifold emarks 1. For the type of mounting valve, see p The order code for the block-off plate sold separately is 00M-B. Manifold Mass 00M8J E E E KE2 5 Block-off plate g Dimensions (Scale 1/2, Unit mm) 00M8J 00M16J D Only 16 stations 36.3 Unit dimensions Model L D 00M8J M16J Connector for flat cable With short clip: Standard With long clip: -LC Option dimensions Type Short clip 12.5 Long clip 15.5 L Mounting hole 1 c1/8 Both sides 16 01E1, 01E E1 00-E2 2-quick fittingfor each unit lug to B for mounting 00E1 lug to for mounting 00E1-11 2B Block-off plate -B

27 Handling Instructions and recautions (C Board Manifold) Solenoid lug connector Manifold Circuit configurations ttaching and removing plug connector rint circuit board For plus common type (standard) Operation example Lead wire: ed Solenoid q w i Lead wire: Black Control signal Corresponding to sequencer Output module is minus common type. q w e r t y u i Use fingers to insert the connector into the pin, push in until the lever claw catches on the convex section on the connector housing, and complete the connection. To remove the connector, squeeze the lever along with the connector, lift the lever claw up from the convex section on the connector housing, and pull out. + C Connector Lever Indication of polarity + C Exclusive lead wire for C board connection Connector assembly void use in the locations listed below, as it may result in deterioration of the print circuit board or shorts in the wiring. If use in such conditions is unavoidable, always provide a cover or other adequate protective measures. 1. Locations subject to high levels of dust or oil mists. 2. Locations subjected to salt, corrosive gases or conductive particles. 3. Locations directly subject to condensation, direct sunlight or other weather effects. SOLENOID VLVES 00 SEIES COM Minus common For minus common typeoption: -CM Operation example Lead wire: Black Solenoid qi: Solenoid 0108:Sequencer output terminal q w i Connector housing Convex section in Cautions: 1. Do not pull hard on the lead wire.it could result in defective contacts, shorted lines, etc. 2. If the pin is bent, use a small screwdriver, etc., to gently straighten out the pin, and then complete the connection to the plug connector. Lead wire: ed Control signal Dedicated lead wire for C board connection Corresponding to sequencer Output module is plus common type. q w e r t y u i COM lus common Cautions: 1. Do not apply megger between the lead wires. 2. While there is no danger with a DC solenoid of a short circuit due to the wrong polarity, the valve will not operate. 3. Leakage current inside the circuit could result in failure of the solenoid valve to return or in other erratic operation. lways use within the range of the allowable leakage current. If circuit conditions, etc., cause the leakage current to exceed the maximum allowable leakage current, consult us.. For double solenoid and twin solenoid, avoid energizing both solenoids simultaneously. The valve could fall into a neutral state. 5. Ensure that voltage drops due to resistance in the cable used remains within the voltage range for the solenoid valve. If the supplied voltage fails to reach the minimum required voltage, the valve could fail to operate properly. Order code by one unit For standard For -CM (Number of wires to use) Order code 00E1 00-E1 00-E2 00-KE2 Y Y Note Y Y Note Note: Y and Y are for dedicated lead wires for double solenoid (solenoid S1 side). Connector for flat cable qi: Solenoid 0108:Sequencer output terminal roduct number Header Clip MIL-C conformity (Made by Sumitomo 3M Ltd.) Triangle mark (First contact pin indication) Socket Flat cable (Equivalent to WG 28: MX. 10m) 123

28 Combined mounting for different type of valves In the 00 Series manifold for combined mounting of 2-, 3-, 5-port valves and C board manifold for combined mounting of 2-, 3-, 5- port valves, single solenoids may be combined with double solenoids, or with twin solenoids, and a total number of up to 8 or 16 solenoids can be mounted. In this case, observe the following precautions. 1. lways use a block-off plate (-B) to close the right station (the side with the higher numbered station) of the station where the double solenoid valve is mounted. 2. If using block-off plates (-B) for some reason other than the above Item 1, place them on the higher numbered stations side. 3. Connector pin numbers are allocated to stations in order from the left end of the manifold. For a double solenoid mounting, the upper pins are allocated to S2 and the lower ones to S1, with the upper S2 numbers being allocated the smaller pin numbers. nd for a twin solenoid mounting, the left side is allocated to S2 and the right side to S1, with the left-side S2 numbers being the smaller pin numbers. Example of an 8 units manifold, with single solenoid valves and 2 double solenoid valves mounted q w e r t S2 u S2 stn.1stn.2stn.3stn. stn.5stn.6 stn.7 stn.8 S1 y S1 i Connector pin locations for 8 units COM. u i t e q y r w emark: The standard is plus common wiring. Minus common wiring is optional (-CM). Example of an 8 units manifold, with 3 single solenoid valves and 2 double solenoid valves mounted q w e r t y u S2 S1 S2 S1 stn.1 stn.2stn.3 stn. stn.6 stn.8 Connector pin locations for 8 units COM. u t e q y r w emark: The standard is plus common wiring. Minus common wiring is optional (-CM). 12