How to setup a remote control of a radio across the mesh. Items needed:

Transcription

1 How to setup a remote control of a radio across the mesh Items needed: - Radio (Yaesu FT-897D used in this example) - Phone Patch (Kenwood PC-1A used here) - Mesh Node - ATA VoIP Adapter (Grandstream HT286 used here) - NTE6408 DIAC (could use NTE6409, 6411 or 6412, depending on the on-hook voltage presented) - Short chunk of telephone cable with RJ-11 - Short section of small coax with 1/8" mono plug - Cabling to connect phone patch to radio (setup specific) - VoIP system (I used the Asterisk server already installed on K5KTF-USB with an extension setup for this use). Details of my system, which may vary from your own setup: I used 2 mesh nodes, K5KTF-USB which is a USB modified node, so I can connect a USB-to-serial adapter cable (PL2303 compatible) that already had the drivers and modules loaded to use the usb-serial cable. I used a separate node, K5KTF-FT-897D, for the VoIP connection. I may at some point move the serial connection over to FT-897D, once I get a spare serial port level shifter to have the CAT cable and the VoIP all one one node. Also, I already have a VoIP system, Asterisk and Chameleon voice mail, already installed on K5KTF-USB, using callsigns as extensions (K5KTF=5583, NG5V=6458, CTECC=28322, etc), so a directory is not needed. Know the callsign/tactical, know their extension. 1 / 11

2 First we connect all the hardware: Whatever phone patch equipment you get will determine how it is connected. In this example. I acquired a KWD PC-1A at the most recent Belton swapfest for $10. I saw 3 or 4 of these floating around up there for about the same price, so they are probably not hard to come by. I wired my Turner Plus Three into the patch box, using just the 4 conductors (Mic/GND, PTT/GND), and tied the patch box to the radio's mic and external speaker jacks. 2 / 11

3 Next strip, screw conduction One more is tin, terminals the and cable, short when tighten across telephone the to CAT5 ring the voltage 2 phone from cable screws the from hits line. ATA on it. the This the to ATA back will the "auto mesh of the the answer" node patch LAN box. the port. The Attach phone RJ-11 the line into DIAC by the going to ATA, both intothen Time Setup DHCP to the reservations start phone configuring mesh to assign node software... in the 1-Host IP for DMZ the adapter. mode, and assign the ATA MAC address to the 3 / 11

4 Now use - it log SIP Extension Authenticate is K5KTF897= ) into SERVER number ATA ID: = the and Usually (on VoIP set my its the server's VoIP settings: same system, main as the wifi I assign extension IP (10.x.x.x) extensions numberbased on callsign, so for this 4 / 11

5 to below line leave At extension. Here Install USB-serial reach this - we Authenticate Name: NAT ONHOOK Polarity Other hung point, as will breakdown ser2net IP: default settings and setup How this you Reversal: The on VOLTAGE: PL2303/equiv IP) can you package 10.x.x.x Password: the (time test voltage other want mesh if this the zone, IP (if the end. This node VoIP option of whatever doing packages CallerID/etc etc) the depends with by DHCP DIAC this set using available, the is as on are setup serial reservation you a to installed USB-modded the softphone appear see port set DIAC the fit. to to and If done VoIP yes, you connect you or modules a use. node, to earlier server do VoIP help not This to also phone (the for loaded know should make that radio. ATA adapter and what (insmod) extension hang be sure dial a set tells setting up the your one ). the when radio's setting does, server the Edit the config file. You only need one line for this to work Make installed, specific I wrote sure a system script and you it that set uses. the runs 4800baud, port at boot speed time so to all match to my set CAT my your serial functions radio. port I have are to 4800 at a that LDG baud speed. AT-897Plus each Verify time. auto what tuner your You to localnode have to add a line to firewall to allow the ser2net to talk. Just set internal and external ports 5 / 11

6 Now the Last Win2000Pro Find ports. Manager node but and start You not Install reboots ser2net only Control least, desktop need the by the Perle Panel, crafting typing to and remote install TruePort Win7 and a ser2net client. 1, script you laptop...works name virtual should Here in {enter}. /etc/rc.d. it whatever serial I see use If on 2 you a port new Windows BOTH). you want, driver devices, like, you (google). PC and can (actually finish. set On this Then install, use up both open to it run asks my Device every to setup time 6 / 11

7 Either adapter in the Perle manager software or in Device Manager, open the settings for the TruePort 7 / 11

8 Set the left. either the 10.x.x.x IP or the node name under Host Name., then click on the COMx Port on 8 / 11

9 Set you Then the set in Connection earlier Device Manager, the mode radio open to node). LITE, the Apply Initiate COM and port connection, OK properties all the and way Port the out. Settings, port to 5001 set as (or appropriate whatever port 9 / 11

10 After Download Upon should The With auto-answer myself softphone HRD all starting just connect settings running and yet) and HRD, install requires should if are your and it set, Ham should will radio take attached, its OK ask own Radio the is all hear for on extension audio the radio use Deluxe and audio. way the from NOT type, out. HRD (free softphone settings the com a or has memory paid) port, setup a to TX and dial button, channel put the port 3CX it radio's speed. VoIP out and Softphone. setting. over (I server. extension. havent Set the appropriately, radio. fully It tested shouldit and it 10 / 11

11 If here Happy Jim K5KTF you (doing followed Meshing! this all from the memory steps and from find 2 I days missed ago something, :-) ) me and I will be glad to fix it 11 / 11