UNITRONIC Data Communication Systems

Transcription

1 Data Communication Systems 156 DeviceNet 162 PROFIBUS 168 CAN Bus 184 RS485/RS AS-Interface 191 Data Highway 194 Interbus 195 Genius 197 CC-Link 198 FOUNDATION Fieldbus 200 Sensor & Actuator Wiring 201 Flexible Data, Signal & Control Cable 205 Flexible UL/CSA Electronic Cable 208 Low Voltage UL/CSA Data, Communication & Control Cable 213 Flexible European Electronic Cable 221 Continuous Flex Data, Signal & Control Cable 227

2 Bus Cable & Connectors BUS CABLE & CONNECTORS Reference Bus Cable Attributes 159 Quick Select Chart 160 DeviceNet BUS DeviceNet, Gray 162 BUS DeviceNet FD, Gray 163 BUS DeviceNet, Violet 164 BUS DeviceNet FD, Violet 165 DeviceNet Field Wireable Connectors 166 DeviceNet PCB Connectors 166 DeviceNet Feed-Through Receptacles 167 DeviceNet T-Connectors 167 PROFIBUS BUS PB 168 BUS PB FD 169 BUS PB FD HYBRID 170 BUS PB TORSION 171 BUS PB FESTOON 172 EPIC Data PROFIBUS Connectors Screw Terminal EPIC Data PROFIBUS Connectors Fast Connect EPIC Data PROFIBUS Connectors Screw Terminal EPIC Data PROFIBUS Connectors LED Screw Terminal EPIC Data PROFIBUS Connectors Spring Type 156

3 EPIC Data PROFIBUS Connectors Fast Connect EPIC Data PROFIBUS Connectors LED Fast Connect EPIC Data PROFIBUS Connectors Screw Terminal EPIC Data PROFIBUS Connectors Fast Connect PROFIBUS Field Wireable M12 Connectors 182 PROFIBUS T-Connectors 182 PROFIBUS Termination Resistors 183 Bus Cable & Connectors CAN Bus BUS CAN 184 BUS CAN FD 185 EPIC Data CAN Bus Connectors Screw Terminal EPIC Data CAN Bus Connectors Screw Terminal CAN Bus Field Wireable M12 Connectors 188 CAN Bus T-Connectors 188 CAN Bus Termination Resistors 189 RS485/RS422 BUS LD & LD FD P 190 AS-Interface BUS ASi 191 BUS ASi FD 192 DIX-ASi 193 Cable Bushings for ASi Bus Cables; PG & Metric Data Highway BUS BlueFlex

4 Bus Cable & Connectors Interbus BUS Interbus 195 BUS Interbus FD 196 Genius BUS Genius 197 CC-Link BUS CC-Link 198 BUS CC-Link FD 199 FOUNDATION Fieldbus BUS FOUNDATION Fieldbus 200 Sensor & Actuator Wiring SENSOR FD 201 Multi-Conductor Continuous Flex Communication Cable with PUR Jacket; 300V M8 Field Wireable Sensor/Actuator Connectors 202 M12 Field Wireable Sensor/Actuator Connectors 203 Bus Cable in Other Catalog Sections PROFIBUS Cordsets 635 DeviceNet Cordsets

5 Reference Bus Cable Attributes Bus System DeviceNet PROFIBUS CAN Bus RS485/RS422 AS-Interface Part Number Oil Resistance Cable Attributes, see page 659 Flame Resistance Motion Type Mechanical Properties 4001, 4002 OR-01 FR-02 FL-02 MP , 6002 OR-01 FR-03 CF-02 MP , OR-02 FR-03 CF-02 MP , OR-00 FR-03 CF-02 MP , OR-04 FR-02 CF-02 MP , OR-02 FR-03 CF-02 MP OR-00 FR-01 FL-01 MP OR-00 FR-02 FL-01 MP OR-00 FR-02 FL-02 MP OR-00 FR-03 FL-01 MP OR-04 FR-03 FL-01 MP OR-04 FR-01 CF-02 MP , OR-04 FR-02 CF-02 MP OR-02 FR-03 CF-02 MP OR-04 FR-02 FL-02 (Torsion ±180 /m) MP OR-02 FR-03 FL-02 (Festoon bending: 70 mm min. bending radius) MP to OR-00 FR-02 FL-02 MP to OR-04 FR-02 CF-02 MP , OR-00 FR-01 FL-02 MP , OR-00 FR-01 FL-02 MP OR-04 FR-01 CF-02 MP OR-04 FR-02 CF-02 MP OR-04 FR-01 CF-02 MP OR-04 FR-02 CF-02 MP OR-04 FR-01 CF-02 MP OR-04 FR-02 CF-02 MP , OR-02 FR-03 CF-02 MP , OR-00 FR-01 FL-02 MP , OR-00 FR-00 FL-02 MP , , OR-04 FR-00 FL-02 MP , , , OR-04 FR-01 CF-02 MP , OR-02 FR-02 CF-02 MP Data Highway 3649FD OR-01 FR-02 CF-01 MP Interbus OR-00 FR-01 FL-02 MP OR-04 FR-01 FL-02 MP OR-00 FR-02 FL-02 MP , OR-04 FR-01 CF-02 MP OR-04 FR-02 CF-02 MP Genius OR-04 FR-02 CF-01 MP CC-Link FOUNDATION Fieldbus Sensor & Actuator Wiring OR-00 FR-03 FL-02 MP OR-04 FR-02 CF-02 MP OR-02 FR-03 FL-02 MP , OR-02 FR-03 FL-00 MP OR-02 FR-03 FL-02 MP to OR-04 FR-01 CF-02 MP Page 159

6 Quick Select Chart: Cable & Connectors Bus Systems Cable Applications Jacket DeviceNet PROFIBUS CAN Bus RS485, RS422 AS-Interface BUS DeviceNet Gray BUS DeviceNet Violet Stationary & Continuous Flex Stationary & Continuous Flex PVC Reference PVC, PUR, Halogen-free BUS PB Stationary PVC, Halogen-free BUS PB FD Continuous Flex PUR BUS PB FD HYBRID Continuous Flex PVC BUS PB TORSION Torsion Halogen-free PUR BUS PB FESTOON Festoon PVC BUS CAN Stationary PVC BUS CAN FD Continuous Flex Halogen-free PUR BUS LD Stationary PVC BUS LD FD P Continuous Flex PUR BUS ASi Stationary & Flexible PVC, Rubber, TPE BUS ASi FD Continuous Flex PUR, TPE Data Highway BUS BlueFlex Continuous Flex PVC Interbus BUS Interbus Stationary PVC, Halogen-free PUR BUS Interbus FD Continuous Flex PUR Genius BUS Genius Continuous Flex PUR CC-Link BUS CC-Link Stationary PVC BUS CC-Link FD Continuous Flex PUR FOUNDATION Fieldbus BUS FOUNDATION Fieldbus Stationary PVC All systems: Sensor & Actuator Wiring SENSOR FD Continuous Flex PUR Connectors for Bus Systems Connector Page DeviceNet Field Wireable Connectors 166 DeviceNet DeviceNet PCB Connectors 166 DeviceNet Feed-Through Receptacles 167 DeviceNet T-Connectors 167 EPIC Data PROFIBUS Connectors, EPIC Data PROFIBUS Connectors, PROFIBUS EPIC Data PROFIBUS Connectors, PROFIBUS Field Wireable M12 Connectors 182 PROFIBUS T-Connectors 182 PROFIBUS Termination Resistors 183 EPIC Data CAN BUS Connectors, EPIC Data CAN BUS Connectors, CAN Bus CAN Bus Field Wireable M12 Connectors 188 CAN Bus T-Connectors 188 CAN Bus Termination Resistors 189 Sensor/Actuator Field Wireable M8 and M12 Sensor/Actuator 202,

7 Reference Impedance Capacitance Voltage Page 12 pf/ft 300V pf/ft 300V pf/ft 250V pf/ft 250V pf/ft 600V pf/ft 300V pf/ft 600V pf/ft 250V pf/ft 250V pf/ft 250V pf/ft 250V pf/ft 300V pf/ft 300V pf/ft 300V pf/ft 250V pf/ft 250V pf/ft 300V pf/ft 300V pf/ft 300V pf/ft 300V V

8 BUS DeviceNet TM Gray DeviceNet THICK DeviceNet THIN BUS DeviceNet cables provide reliable data and power transfer between industrial automation devices like sensors, actuators & PLCs. The cables are designed to perform in harsh chemical & mechanical DeviceNet TM Construction Conductors: Stranded tinned copper Insulation: Power conductors: PVC; Data conductors: Polyethylene Shielding: Pairs: tri-laminated foil shield (100% coverage); tinned copper drain wire; overall foil wrap and braid (65% coverage) Jacket: Gray PVC Recommended Applications DeviceNet bus systems; wiring of automation devices like sensors, actuators, PLCs, and PCs Cable can supply device with power and data, wiring is minimized Communication rate up to 500 Kbps Oil-resistant PVC jacket Rate Table Lapp Systems Advantage Communication Rate Maximum Length: Trunk Cable Maximum Length: Drop Cable THICK THIN THICK THIN (feet) (meters) (feet) (meters) (feet) (meters) (feet) (meters) 125 Kbps Kbps Kbps For DeviceNet cordsets, see page 640 Cable Attributes, see page 659 OR-01 FR-02 FL-02 MP-01 OIL FLAME MOTION MECHANICAL Similar Cables BUS DeviceNet Violet MS-SC: page 528 Minimum Bend Radius: - for installation: 10 x cable diameter Characteristic Impedance: -20 C to +75 C 300V Nominal Capacitance: 12 pf/ft Color Code: - Power pair: Red & black - Data pair: Blue & white : UL: CL2 Canada: CSA AWM Part Number Type Conductor Description Nominal Outer Diameter (AWG/Pair) (inches) (mm) (lbs/mft) (lbs/mft) MS-SC Stationary 4001 Thick 18 AWG/1pr + 15 AWG/1pr Thin 24 AWG/1pr + 22 AWG/1pr Recommended 162

9 DeviceNet DeviceNet THICK DeviceNet THIN BUS DeviceNet FD cables provide reliable data and power transfer between industrial automation devices like sensors, actuators & PLCs. The cables are designed to perform in harsh chemical & mechanical BUS DeviceNet TM FD Gray Construction Conductors: Stranded tinned copper Insulation: Power conductors: PVC; Data conductors: Polyethylene Shielding: Pairs: tri-laminated foil shield (100% coverage); tinned copper drain wire; overall foil wrap and braid (65% coverage) Jacket: Gray PVC Recommended Applications DeviceNet bus systems; cable tracks and moving machine parts, wiring of automation devices like sensors, actuators, PLCs, and PCs Cable can supply device with power and data, wiring is minimized Communication rate up to 500 Kbps Oil-resistant PVC jacket Rate Table Lapp Systems Advantage Communication Rate Maximum Length: Trunk Cable Maximum Length: Drop Cable THICK THIN THICK THIN (feet) (meters) (feet) (meters) (feet) (meters) (feet) (meters) 125 Kbps Kbps Kbps For DeviceNet cordsets, see page 640 Cable Attributes, see page 659 OR-01 FR-03 CF-02 MP-01 OIL FLAME MOTION MECHANICAL Similar Cables BUS DeviceNet FD Violet MS-SC: page 528 Minimum Bend Radius: Characteristic Impedance: -20 C to +75 C 300V Nominal Capacitance: 12 pf/ft Color Code: - Power pair: Red & black - Data pair: Blue & white : UL: CL2 CM (6002) Canada: CSA AWM (6001) CSA CMG (6002) Part Number Type Conductor Description Nominal Outer Diameter (AWG/Pair) (inches) (mm) (lbs/mft) (lbs/mft) MS-SC Continuous Flex 6001 Thick 18 AWG/1pr + 14 AWG/1pr Thin 24 AWG/1pr + 22 AWG/1pr Recommended Section. Photographs are not to scale and are not true 163

10 BUS DeviceNet Violet DeviceNet THICK DeviceNet THIN BUS DeviceNet cables provide reliable data and power transfer between industrial automation devices like sensors, actuators & PLCs. The cables are designed to perform in harsh chemical & mechanical Recommended Applications DeviceNet bus systems; wiring of automation devices like sensors, actuators, PLCs, and PCs DeviceNet Construction Conductors: Stranded tinned copper Insulation: Power conductors: PVC (PVC jacket); polyethylene (Halogen-free jacket); Data conductors: Polyethylene Shielding: Pairs: tri-laminated foil shield; tinned copper drain wire; overall foil wrap and braid Jacket: Violet PVC or halogen-free Cable can supply device with power and data, minimizing wiring Communication rate up to 500Kbps Oil-resistant PVC or abrasion-resistant PUR Cable Attributes See attribute list by part number on page 159 OIL FLAME MOTION MECHANICAL Similar Cables BUS DeviceNet Gray MS-SC: page528 Minimum Bend Radius: - for installation: 7.5 x cable diameter - PVC: -20 C to +75 C - Halogen-free -25 C to +75 C 300V Color Code: - Power pair: Red & black - Data pair: Blue & white : UL: CMG PLTC ( , ) CL2 ( ) Canada: c(ul) CMG Characteristic Impedance: Nominal Capacitance: 12 pf/ft Part Number Type Conductor Description Nominal Outer Diameter (AWG/Pair) (inches) (mm) (lbs/mft) (lbs/mft) MS-SC Stationary: PVC Thick 18 AWG/1pr + 15 AWG/1pr Thin 24 AWG/1pr + 22 AWG/1pr Stationary: Halogen-Free & Flame Retardant (FRNC) Thick 18 AWG/1pr + 15 AWG/1pr Thin 24 AWG/1pr + 22 AWG/1pr Recommended 164

11 DeviceNet DeviceNet THICK FD P DeviceNet THIN FD P BUS DeviceNet FD cables provide reliable data and power transfer between industrial automation devices like sensors, actuators & PLCs. The cables are designed to perform in harsh chemical & mechanical Recommended Applications DeviceNet bus systems; cable tracks and moving machine parts; wiring of automation devices like sensors, actuators, PLCs, and PCs BUS DeviceNet FD Violet Construction Conductors: Stranded tinned copper Insulation: Power conductors: PVC (PVC jacket); polyethylene (PUR jacket); Data conductors: Polyethylene Shielding: Pairs: tri-laminated foil shield; tinned copper drain wire; overall foil wrap and braid Jacket: Violet PVC or PUR Cable can supply device with power and data, minimizing wiring Communication rate up to 500Kbps Oil-resistant PVC or halogen-free jacket options Cable Attributes See attribute list by part number on page 159 OIL FLAME MOTION MECHANICAL Similar Cables BUS DeviceNet FD Gray MS-SC: page 528 Minimum Bend Radius: - PUR: -40 C to +75 C - PVC: -10 C to +75 C Characteristic Impedance: Nominal Capacitance: 300V 12 pf/ft Color Code: - Power pair: Red & black - Data pair: Blue & white : UL: CMG ( , ) CMX ( , ) PLTC ( ) CLX2 ( , ) CL2 ( ) Canada: c(ul) CMG ( , ) c(ul) CMX ( , ) Part Number Type Conductor Description Nominal Outer Diameter (AWG/Pair) (inches) (mm) (lbs/mft) (lbs/mft) MS-SC Continuous Flex: PUR Thick 18 AWG/1pr + 15 AWG/1pr Thin 24 AWG/1pr + 22 AWG/1pr Continuous Flex: PVC Thick 18 AWG/1pr + 15 AWG/1pr Thin 24 AWG/1pr + 22 AWG/1pr Recommended 165

12 DeviceNet Field Wireable Connectors DN DN DN DN DN DN DN DeviceNet DN Nominal Current: max +85 C 250V/125V 4A or 9A Quick & easy on-site assembly Part Number Number of Positions PG Connection Min. Cable Diameter (mm) Max. Cable Diameter Nominal Voltage Nominal Current (mm) DN PG V 9A DN PG V 9A DN PG V 9A DN PG V 9A M12 Straight Male Connector, Screw Connection DN PG V 4A M12 Straight Female Connector, Screw Connection DN PG V 4A M12 90 Male Connector, Screw Connection DN PG V 4A M12 90 Female Connector, Screw Connection DN PG V 4A DeviceNet PCB Connectors DN DN DN C to 105 C Part Number End Connector Number of Positions Nominal Voltage Nominal Current PCB Connectors DN V 9A DN Female M V 4A DN Male M V 4A Photographs are not to scale and are not true representations of the products in question. 166

13 DeviceNet DN DeviceNet Feed-Through Receptacles DN C to 75 C Protection Rating: IP67 Part Number End Connector 1 End Connector 2 Nominal Voltage Nominal Current Feed-Through Receptacles DN V 9A DN Male M12 5-position Female M12 5-position 250V 4A DeviceNet T-Connectors DN DN DN C to 75 C Part Number End Connector 1 End Connector 2 End Connector 3 Nominal Voltage Nominal Current T-Connectors DN V 9A DN Female M12 5-position Female M12 5-position Male M12 5-position 250V 4A DN Female M12 5-position 250V 4A Photographs are not to scale and are not true representations of the products in question. 167

14 BUS PB BUS PB BUS PB FC PROFIBUS Construction Conductors: Solid and stranded bare copper Insulation: Polyethylene Shielding: Specially designed foil/tinned copper braid Jacket: Violet PVC (except : halogen-free) BUS PROFIBUS cables are designed for automation networks devices. Additional styles are available upon request (e.g., armored, high temperature, direct burial for outdoor, PROFIBUS PA for intrinsic safety). Recommended Applications Wiring of automation devices like sensors, actuators, PLCs, and PCs in dry or damp environments; PROFIBUS bus systems DP, FMS, and FIP Maximum Cable Length by Bit Rate for One Bus Segment Communication Rate Length of Cable Segment (feet) (meters) Kbps Kbps Kbps Mbps Mbps Maximum EMI protection Fast connect style for quick installation Communication rate up to 12.0 Mbit/s Lapp USA is a member of the PROFIBUS User Organization (PNO) Call your sales representative for additional styles Lapp Systems Advantage For PROFIBUS cordsets, see page 635 Cable Attributes See attribute list by part number on page 159 OIL FLAME MOTION MECHANICAL Similar Cables BUS PB FD MS-SC: page 528 EPIC Data Connectors page 173 Minimum Bend Radius: - for installation: 10 x cable diameter - PVC: -40 C to +80 C - Halogen-free: -30 C to +80 C Characteristic Impedance: Color Code: Red & green pair : UL: CMG (see table below) CMX ( ) CL3 ( , ) Canada: cul CMG (see table below) c UL CMX ( ) Nominal Capacitance: 9 pf/ft Part Number Jacket Type Nominal Conductor Description Outer Diameter (AWG/Pair) (inches) (mm) (lbs/mft) (lbs/mft) MS-SC Stationary PVC 22 AWG/1pr PVC 22 AWG/1pr UL/CSA CMX * PVC 24 AWG/1pr, 7 wire UL/CSA CMG Stationary: Fast Connect PVC 22 AWG/1pr UL/CSA CMG Halogen-free 22 AWG/1pr UL/CSA CMG *For applications where vibrations occur. Recommended 168

15 PROFIBUS BUS PB FD BUS PB FD P BUS PB FD P FC BUS PROFIBUS FD cables are designed for automation networks requiring fast and reliable data exchange between controllers and Construction Conductors: Stranded bare copper Insulation: Polyethylene Shielding: Specially designed foil/tinned copper braid Jacket: Violet polyurethane Recommended Applications PROFIBUS bus systems DP, FMS, and FIP Fast connect style for quick installation Communication rate up to 12 Mbit/s Lapp USA is a member of the PROFIBUS User Organization (PNO) Lapp Systems Advantage For PROFIBUS cordsets, see page 635 Cable Attributes See attribute list by part number on page 159 OIL FLAME MOTION MECHANICAL Similar Cables BUS PB TORSION MS-SC: page 528 EPIC Data Connectors: page 173 Minimum Bend Radius: & : 9 x cable diameter : 15 x cable diameter - for stationary use: -40 C to +80 C Nominal Capacitance: Color Code: 9 pf/ft Red & green pair : UL: CMX ( , ) Canada: c(ul) CMX ( , ) Additional: Torsion rated for Wind Market (± 150 /m) ( , ) Characteristic Impedance: Part Number Jacket Type Nominal Conductor Description Outer Diameter (AWG/Pair) (inches) (mm) (lbs/mft) (lbs/mft) MS-SC Continuous Flex PUR 24 AWG/1pr PUR 24 AWG/1pr UL/CSA CMX Continuous Flex: Fast Connect PUR 24 AWG/1pr UL/CSA CMX Recommended 169

16 UNTRONIC BUS PB FD HYBRID PB FD HYBRID BUS PB FD HYBRID is designed for automation networks devices. PROFIBUS Construction Conductors: Data pairs: stranded bare copper; Power conductors: stranded bare copper Insulation: Data pairs: Polyethylene; Power conductors: PVC Shielding: Screened pair and 4 control conductors twisted together with yarn; Data pairs: specially designed foil/tinned copper braid Jacket: Violet PVC Recommended Applications moving machine parts; PROFIBUS bus systems DP, FMS, and FIP Hybrid cable for data transmission and power supply Sunlight resistant Lapp USA is a member of the PROFIBUS User Organization (PNO) Cable Attributes, see page 659 OR-02 FR-03 CF-02 MP-01 OIL FLAME MOTION MECHANICAL Similar Cables BUS PB FD Strain Relief: page 502 Minimum Bend Radius: - for stationary use: 10 x cable diameter -5 C to +80 C Nominal Capacitance: 9 pf/ft Color Code: - Data pairs: Red & green - Power conductors: Black cores numbered 1, 2, 3, 4 Characteristic Impedance: 600V (not for power applications) : UL: CMG CL3 Canada: c(ul) CMG Part Number Jacket Type Conductor Description Approval Nominal Outer Diameter (AWG/Pair + AWG/Conductors) (inches) (mm) (lbs/mft) (lbs/mft) Non-Metallic Continuous Flex PVC 24 AWG/1pr + 16 AWG/4c UL/CSA CMG S2116 Recommended 170

17 PROFIBUS BUS PB TORSION BUS PB TORSION BUS PB TORSION is designed for automation networks devices. Construction Conductors: Stranded bare copper Insulation: Polyethylene Shielding: Specially designed foil/tinned copper braid Jacket: Violet halogen-free polyurethane Recommended Applications Torsion applications like robots; PROFIBUS bus systems DP, FMS, and FIP Communication rate up to 12 Mbit/s Lapp USA is a member of the PROFIBUS User Organization (PNO) Cable Attributes, see page 659 OR-04 FR-02 FL-02 MP-05 OIL FLAME MOTION MECHANICAL Similar Cables BUS PB FD MS-SC: page 528 EPIC Data Connectors: page 173 Minimum Bend Radius: - for stationary use: 4 x cable diameter Nominal Capacitance: Color Code: 9 pf/ft Red & green pair -25 C to +75 C 300V (not for power applications) : UL: CMX Canada: c(ul) CMX Characteristic Impedance: Part Number Jacket Type Conductor Description Approval Nominal Outer Diameter (AWG/Pair) (inches) (mm) (lbs/mft) (lbs/mft) MS-SC Torsion PUR 22 AWG/1pr UL/CSA CMX Recommended 171

18 BUS PB FESTOON BUS PB FESTOON BUS PB FESTOON is designed for automation networks devices. PROFIBUS Construction Conductors: Stranded bare copper Insulation: Polyethylene Shielding: Specially designed foil/tinned copper braid Jacket: Violet PVC Recommended Applications Festoon applications like cable trolleys; PROFIBUS bus systems DP, FMS, CL3 rating for installation in trays and FIP Communication rate up to 12 Mbit/s Sunlight resistant Lapp USA is a member of the PROFIBUS User Organization (PNO) Cable Attributes, see page 659 OR-02 FR-03 FL-02 MP-01 OIL FLAME MOTION MECHANICAL Similar Cables BUS PB FD MS-SC: page 528 EPIC Data Connectors: page 173 Minimum Bend Radius: - for stationary use: 4 x cable diameter Characteristic Impedance: Nominal Capacitance: 9 pf/ft - for stationary use: -40 C to +75 C 600V (not for power applications) Color Code: : Red & green pair UL: CMG CL3 Canada: c(ul) CMG Part Number Jacket Type Conductor Description Approval Nominal Outer Diameter (AWG/Pair) (inches) (mm) (lbs/mft) (lbs/mft) MS-SC Continuous Flex PVC 24 AWG/1pr UL/CSA CMG Recommended 172

19 PROFIBUS EPIC Data PROFIBUS Connectors 35 Screw Terminal EPIC Data PROFIBUS connectors are screw terminal, 9 pin D-Sub connectors with an integrated adjustable termination resistor. The cable entry is 35 angled. Connectors are available with additional programming/diagnostic interface. Usage Notes position. If used as a terminating connector the switch must be in the disconnected. Switch is clearly visible when connector is plugged in and operational. Design Dimensions: 54 mm x 40mm x 17 mm (L x W x H) Connection Type: Screw terminal For Cable Diameter: in (5-8 mm) Terminating Resistor: Integrated resistor combination that is connected by a sliding switch Interface: 9 pin D-Sub socket : 40g Insertion/Withdrawal Cycles: > 200 Standardized interfaces Cost-saving due to quick installation Easy to connect Small design Fully compatible with market standard - Operating: 0 C to +60 C - Transport & storage: -25 C to +80 C - Relative humidity: max. 75% at +25 C Protection Rating: Supply Voltage: Transmission Rate: IP V DC max. 12 Mbit/s Current Consumption: max ma Interfaces: - PROFIBUS station: 9 pin D-Sub socket - PROFIBUS cable: 4 terminal blocks for wires up to 1 mm 2 : UL: Programmable Controllers: Components Component Additional: CE & RoHS D -Sub pin assignment in accordance with PROFIBUS Part Number Cable Outlet Programming/Diagnostics EPIC Data PROFIBUS Connectors No Yes Photographs are not to scale and do not represent detailed images of the respective products. 173

20 EPIC Data PROFIBUS Connectors 35 Fast Connect PROFIBUS EPIC Data PROFIBUS connectors are fast connect, 9 pin D-Sub connectors with an integrated adjustable termination resistor. The cable entry is 35 angled. Connectors are available with additional programming/diagnostic interface. Usage Notes position. If used as a terminating connector the switch must be in the disconnected. Switch is clearly visible when connector is plugged in. Design Dimensions: 95 mm x 70 mm x 17 mm (L x W x H) Connection Type: Fast connect For Cable Diameter: in (5-8 mm) Terminating Resistor: Integrated resistor combination that is connected by a sliding switch Interface: 9 pin D-Sub socket : 50g Insertion/Withdrawal Cycles: > 200 Suitable for FC cables Standardized interfaces Cost-saving due to quick installation Easy to connect Fully compatible with market standard - Operating: 0 C to +60 C - Transport & storage: -25 C to +80 C - Relative humidity: max. 75% at +25 C Protection Rating: Supply Voltage: Transmission Rate: IP V DC (supplied from terminal) max. 12 Mbit/s Current Consumption: max ma Interfaces: - PROFIBUS station: 9 pin D-Sub socket - PROFIBUS cable: FC standard cable ø 0.64 mm : UL: Programmable Controllers: Components Component Additional: CE & RoHS D -Sub pin assignment in accordance with PROFIBUS Part Number Cable Outlet Cable Type Programming/Diagnostics EPIC Data PROFIBUS Connectors Solid No Solid Yes Stranded No Stranded Yes FC Stripping Tool page 259 Photographs are not to scale and do not represent detailed images of the respective products. 174

21 PROFIBUS EPIC Data PROFIBUS Connectors 90 Screw Terminal EPIC Data PROFIBUS connectors are screw terminal, 9 pin D-Sub connectors with an integrated adjustable termination resistor. The cable entry is 90 angled. Connectors are available with additional programming/ diagnostic interface. Usage Notes position. If used as a terminating connector the switch must be in the disconnected. Switch is clearly visible when connector is terminated. Design Dimensions: 64 mm x 40 mm x 17 mm (L x W x H) Connection Type: Screw terminal For Cable Diameter: in (5-8 mm) Terminating Resistor: Integrated resistor combination that is connected by a sliding switch Interface: 9 pin D-Sub socket : 40g Insertion/Withdrawal Cycles: > 200 Standardized interfaces Cost-saving due to quick installation Easy to connect Small Design Fully compatible with market standard - Operating: 0 C to +60 C - Transport & storage: -25 C to +80 C - Relative humidity: max. 75% at +25 C Protection Rating: IP20 Current Consumption: max ma Interfaces: - PROFIBUS station: 9 pin D-Sub socket - PROFIBUS cable: 4 terminal blocks for wires up to 1 mm 2 Supply Voltage: Transmission Rate: V DC (supplied from terminal) max. 12 Mbit/s : UL: Programmable Controllers: Components Component Additional: CE & RoHS D -Sub pin assignment in accordance with PROFIBUS Part Number Cable Outlet Programming/Diagnostics EPIC Data PROFIBUS Connectors No Yes Photographs are not to scale and do not represent detailed images of the respective products. 175

22 EPIC Data PROFIBUS Connectors 90 LED Screw Terminal PROFIBUS EPIC Data PROFIBUS connectors are screw terminal, 9 pin D-Sub connectors with an integrated adjustable termination resistor. The cable entry is 90 angled. Connectors are available with additional programming/ diagnostic interface. Usage Notes position. If used as a terminating connector the switch must be in the disconnected. Switch is clearly visible when connector is plugged in and operational. Design Dimensions: 64 mm x 40 mm x 17 mm (L x W x H) Connection Type: Screw terminal For Cable Diameter: in. (5-8 mm) Terminating Resistor: Integrated resistor combination that is connected by a sliding switch Interface: 9 pin D-Sub socket : 40g Insertion/Withdrawal Cycles: > status LEDs indicate: bus operation, station transmission, terminating resistance Easy troubleshooting Cost-saving due to quick installation Easy to connect Fully compatible with market standard Temperature: - Operating: 0 C to +60 C - Transport & storage: -25 C to +80 C - Relative humidity: max. 75% at +25 C Protection Rating: IP20 Current Consumption: max. 35 ma Interfaces: - PROFIBUS station: 9 pin D-Sub socket - PROFIBUS cable: 4 terminal blocks for wires up to 1 mm 2 Supply Voltage: Transmission Rate: V DC (supplied from terminal) max. 12 Mbit/s : UL: Programmable Controllers: Components Component Additional: CE & RoHS D -Sub pin assignment in accordance with PROFIBUS Part Number Cable Outlet Programming/Diagnostics EPIC Data PROFIBUS Connectors No Yes Photographs are not to scale and do not represent detailed images of the respective products. 176

23 PROFIBUS EPIC Data PROFIBUS Connectors 90 Spring Type EPIC Data PROFIBUS connectors are spring-type, 9 pin D-Sub connectors with an integrated adjustable termination resistor. The cable entry is 90 angled. Connectors are available with additional programming/diagnostic interface. Usage Notes position. If used as a terminating connector the switch must be in the disconnected. Contact is automatically created when the stripped conductor is inserted into the spring terminal. The orange lever must be pressed to break the connection. Switch is clearly visible when connector is plugged in and operational. Design Dimensions: 65 mm x 48 mm x 16 mm (L x W x H) Connection Type: Spring type For Cable Diameter: in. (5-8 mm) Terminating Resistor: Integrated resistor combination that is connected by a sliding switch Interface: 9 pin D-Sub socket : 40g Insertion/Withdrawal Cycles: > 200 Standardized interfaces Cost-saving due to quick installation Easy to connect Fully compatible with market standard Temperature: - Operating: 0 C to +60 C - Transport & storage: -25 C to +80 C - Relative humidity: max. 75% at +25 C Protection Rating: IP20 Current Consumption: max ma Interfaces: - PROFIBUS station: 9 pin D-Sub socket - PROFIBUS cable: 4 spring type terminals for wires up to 0.5 mm 2 (solid conductor) Supply Voltage: Transmission Rate: V DC (supplied from terminal) max. 12 Mbit/s : UL: Programmable Controllers: Components Component Additional: CE & RoHS D -Sub pin assignment in accordance with PROFIBUS Part Number Cable Outlet Cable Type Programming/Diagnostics EPIC Data PROFIBUS Connectors Solid No Solid Yes Photographs are not to scale and do not represent detailed images of the respective products. 177

24 EPIC Data PROFIBUS Connectors 90 Fast Connect PROFIBUS EPIC Data PROFIBUS connectors are fast connect, 9 pin D-Sub connector with an integrated adjustable termination resistor. The cable entry is 90 angled. Connectors are available with additional programming/diagnostic interface. Usage Notes position. If used as a terminating connector the switch must be in the disconnected. Switch is clearly visible when connector is plugged in and operational. Design Dimensions: 72 mm x 40 mm x 17 mm (L x W x H) Connection Type: Fast connect For Cable Diameter: in (5-8 mm) Terminating Resistor: Integrated resistor combination that is connected by a sliding switch Interface: 9 pin D-Sub socket : 40g Insertion/Withdrawal Cycles: > 200 Suitable for FC cables Standardized interfaces Cost-saving due to quick installation Easy to connect Fully compatible with market standard Temperature: - Operating: -25 C to +70 C - Transport & storage: -25 C to +80 C - Relative humidity: max. 75% at +25 C Protection Rating: Supply Voltage: Transmission Rate: IP V DC (supplied from terminal) max. 12 Mbit/s Current Consumption: max ma Interfaces: - PROFIBUS station: 9 pin D-Sub socket - PROFIBUS cable: FC standard cable ø 0.64 mm : UL: Programmable Controllers: Components Component Additional: CE & RoHS D -Sub pin assignment in accordance with PROFIBUS Part Number Cable Outlet Cable Type Programming/Diagnostics EPIC Data PROFIBUS Connectors Solid No Solid Yes Stranded No Stranded Yes FC Stripping Tool page 259 Photographs are not to scale and do not represent detailed images of the respective products. 178

25 PROFIBUS EPIC Data PROFIBUS Connectors 90 LED Fast Connect EPIC Data PROFIBUS connectors are fast connect, 9 pin D-Sub connector with an integrated adjustable termination resistor. The cable entry is 90 angled. Connectors are available with additional programming/diagnostic interface. Usage Notes position. If used as a terminating connector the switch must be in the disconnected. Switch is clearly visible when connector is plugged in and operational. Design Dimensions: 64 mm x 40 mm x 17 mm (L x W x H) Connection Type: Fast connect For Cable Diameter: in (5-8 mm) Terminating Resistor: Integrated resistor combination that is connected by a sliding switch Interface: 9 pin D-Sub socket : 40g Insertion/Withdrawal Cycles: > status LEDs indicate: bus operation, station transmission, terminating resistance Easy troubleshooting Visual connection control Cost-saving due to quick installation Easy to connect Fully compatible with market standard Temperature: - Operating: 0 C to +60 C - Transport & storage: -25 C to +80 C - Relative humidity: max. 75% at +25 C Protection Rating: Supply Voltage: Transmission Rate: IP V DC (supplied from terminal) max. 12 Mbit/s Current Consumption: max. 35 ma Interfaces: - PROFIBUS station: 9 pin D-Sub socket - PROFIBUS cable: FC standard cable ø 0.64 mm : UL: Programmable Controllers: Components Component Additional: CE & RoHS D -Sub pin assignment in accordance with PROFIBUS Part Number Cable Outlet Cable Type Programming/Diagnostics EPIC Data PROFIBUS Connectors Solid No Solid Yes Stranded No Stranded Yes FC Stripping Tool page 259 Photographs are not to scale and do not represent detailed images of the respective products. 179

26 EPIC Data PROFIBUS Connectors 180 Screw Terminal PROFIBUS EPIC Data PROFIBUS connectors are screw terminal, 9 pin D-Sub connectors with an integrated adjustable termination resistor. The cable entry is 180. Connectors are available with additional programming/ diagnostic interface. Usage Notes position. If used as a terminating connector the switch must be in the disconnected. Switch is clearly visible when connector is plugged in and operational. Design Dimensions: 68 mm x 39.5 mm x 17 mm (L x W x H) Connection Type: Screw terminal For Cable Diameter: in (5-8 mm) Terminating Resistor: Integrated resistor combination that is connected by a sliding switch Interface: 9 pin D-Sub socket : 40g Insertion/Withdrawal Cycles: > 200 Standardized interfaces Cost-saving due to quick installation Easy to connect Fully compatible with market standard Temperature: - Operating: 0 C to +60 C - Transport & storage: -25 C to +80 C - Relative humidity: max. 75% at +25 C Protection Rating: Supply Voltage: Transmission Rate: IP V DC (supplied from terminal) max. 12 Mbit/s Current Consumption: max ma Interfaces: - PROFIBUS station: 9 pin D-Sub socket - PROFIBUS cable: 4 terminal blocks for wires up to 1 mm 2 : UL: Programmable Controllers: Components Component Additional: CE & RoHS D -Sub pin assignment in accordance with PROFIBUS Part Number Cable Outlet Programming/Diagnostics EPIC Data PROFIBUS Connectors No Photographs are not to scale and do not represent detailed images of the respective products. 180

27 PROFIBUS EPIC Data PROFIBUS Connectors 180 Fast Connect EPIC Data PROFIBUS connectors are fast connect, 9 pin D-Sub connectors with an integrated adjustable termination resistor. The cable entry is 180. Connectors are available with additional programming/diagnostic interface. Usage Notes position. If used as a terminating connector the switch must be in the disconnected. Switch is clearly visible when connector is plugged in and operational. Design Dimensions: 70 mm x 35 mm x 17 mm (L x W x H) Connection Type: Fast connect For Cable Diameter: in (5-8 mm) Terminating Resistor: Integrated resistor combination that is connected by a sliding switch Interface: 9 pin D-Sub socket : 50g Insertion/Withdrawal Cycles: > 200 Suitable for FC cables Standardized interfaces Cost-saving due to quick installation Easy to connect Fully compatible with market standard Temperature: - Operating: -25 C to +70 C - Transport & storage: -25 C to +80 C - Relative humidity: max. 75% at +25 C Protection Rating: Supply Voltage: Transmission Rate: IP V DC (supplied from terminal) max. 12 Mbit/s Current Consumption: max. 12 ma Interfaces: - PROFIBUS station: 9 pin D-Sub socket - PROFIBUS cable: FC standard cable ø 0.64 mm : UL: Programmable Controllers: Components Component Additional: CE & RoHS D -Sub pin assignment in accordance with PROFIBUS Part Number Cable Outlet Cable Type Programming/Diagnostics EPIC Data PROFIBUS Connectors Solid No Stranded No FC Stripping Tool page 259 Photographs are not to scale and do not represent detailed images of the respective products. 181

28 PROFIBUS Field Wireable M12 Connectors PROFIBUS Quick and easy on-site assembly Robust shielded design Space-saving compact design -40 C to +85 C Screw Connection: PG 9 60V Coding: B-inverse Nominal Current: 4A Protection Rating: IP67 Contact Resistance: : RoHS Part Number Number of Positions Coding Conductor Cross Section (mm) Conductor Cross Section (AWG) Cable Diameter (mm) Min. Max. Min. Max. Min. Max. M12 Straight Male Connector, Screw Connection B-inverse M12 Straight Female Connector, Screw Connection B-inverse PROFIBUS T-Connectors Robust shielded design Space-saving compact design Standardized interfaces -25 C to +80 C 60V Screw Connection: Male M12 connector to female M12 connector and male M12 connector Nominal Current: 4A Coding: B-inverse Contact Resistance: Protection Rating: IP67 : RoHS Photographs are not to scale and are not true representations of the products in question. 182 Part Number Number of Pins Coding Nominal Voltage Nominal Current M12 T-Connector B-inverse 60V 4A

29 PROFIBUS PROFIBUS Termination Resistors Robust design Standardized interfaces Space-saving compact design Female connector with shielded design - Male: -25 C to +95 C - Female: -40 C to +85 C - Male: 60V - Female: 32V Coding: B-inverse Protection Rating: - Male: IP65/IP67/IP69K - Female: IP67 : RoHS Nominal Current: Contact Resistance: 4A Number of Part Number Coding Nominal Voltage Nominal Current Standard Pack Positions M12 Straight Male Connector with Integrated Termination Resistor B-inverse 60V 4A 5 M12 Straight Female Connector with Integrated Termination Resistor, Shielded B-inverse 32V 4A 5 Photographs are not to scale and are not true representations of the products in question. 183

30 BUS CAN BUS CAN BUS CAN is designed to the CAN open and ISO11898 standard. It is well suited for high-speed motion control and feedback bandwidth. Recommended Applications Motion control systems; assembly, welding, and material handling machines; single cable wiring of multi-input sensor blocks; smart sensors; pneumatic valves; barcode readers; drives and operator interfaces Construction Conductors: 7-wire strands of bare copper Insulation: Polyethylene Shielding: Foil wrap; tinned copper braid shield Jacket: Violet PVC CAN Bus Signal integrity in stationary motion applications Flame retardant Oil-resistant jacket Flexible for ease of routing Rate Table (ISO Recommendations) Distance (m) AWG Max. Rate m , m m km Cable Attributes, see page659 OR-00 FR-02 FL-02 MP-01 OIL FLAME MOTION MECHANICAL Similar Cables BUS CAN FD MS-SC: page 528 CAN Bus Connectors page 186 Minimum Bend Radius: 10 x cable diameter Nominal Capacitance: 12 pf/ft -30 C to +80 C 250V Color Code: DIN 47100: Chart 8, page Pair 1: White & brown - Pair 2: Green & yellow Characteristic Impedance: : UL: CMX Canada: cul CMX Recommended 184 Part Number Conductor Description Nominal Outer Diameter (AWG/Pair) (inches) (mm) (lbs/mft) (lbs/mft) MS-SC Stationary AWG/1pr AWG/2pr AWG/1pr AWG/2pr AWG/1pr AWG/2pr AWG/1pr AWG/2pr

31 CAN Bus BUS CAN FD BUS CAN FD Construction Construction: Insulation: Recommended Applications Rate Table (ISO Recommendations) Distance (m) AWG Max. Rate 22 Cable Attributes, see page 659 OIL MOTION Similar Cables BUS CAN CAN Bus Connectors Minimum Bend Radius: Nominal Capacitance: Color Code: Characteristic Impedance: : UL: CMX Canada: c UL CMX Part Number Conductor Description Nominal Outer Diameter (AWG/Pair) (inches) (mm) (lbs/mft) (lbs/mft) MS-SC Continuous Flex Recommended 185

32 EPIC Data CAN Bus Connectors 90 Screw Terminal CAN Bus EPIC with an integrated adjustable termination resistor. The cable entry is 90 interface. Usage Notes When used as a through connector the switch must be in the OFF Design Dimensions: 65 mm x 48 mm x 16 mm (L x W x H) Connection Type: Screw terminal For Cable Diameter: in (5-8 mm) Terminating Resistor: with slide switch Interface: 9 pin D-Sub socket : 40 g Insertion/Withdrawal Cycles: > 200 Temperature: Protection Rating: Transmission Rate: IP20 max. 1 Mbit/s With additional 24V DC output to supply external Easy to connect Standardized interfaces Small design Interfaces: 9 pin D-Sub socket 6 terminal blocks for wires up to 1 mm 2 : UL: Programmable Controllers: Components Component Part Number Cable Outlet Programming/Diagnostics EPIC Data CAN Bus Connectors Yes Photographs are not to scale and are not true representations of the products in question. 186

33 CAN Bus EPIC Data CAN Bus Connectors 180 Screw Terminal EPIC with an integrated adjustable termination resistor. The cable entry is 180. Usage Notes When used as a through connector the switch must be in the OFF ON position. No loose parts. Design Dimensions: 67.5 mm x 35 mm x 17 mm (L x W x H) Connection Type: Screw terminal For Cable Diameter: in (5-8 mm) Terminating Resistor: connectable with slide switch Interface: 9 pin D-Sub socket : 40 g Insertion/Withdrawal Cycles: > 200 Easy to connect Standardized interfaces Temperature: - Operating: 0 C to +60 C - Transport & storage: -25 C to +75 C Protection Rating: IP20 Interfaces: - CAN bus station: 9 pin D-Sub socket - CAN bus cable: 6 terminal blocks for wires up to 1 mm 2 - D-Sub assignments: Pin 2: CAN Low Pin 7: CAN High Pin 3: CAN Gnd Transmission Rate: max. 1 Mbit/s : UL: Programmable Controllers: Components Component Additional: CE & RoHS Part Number Cable Outlet Programming/Diagnostics EPIC Data CAN Bus Connectors No Photographs are not to scale and are not true representations of the products in question. 187

34 CAN Bus Field Wireable M12 Connectors CAN Bus Quick and easy on-site assembly Robust shielded design Space-saving compact design -40 C to +85 C Screw Connection: PG 9 60V Coding: A-standard Nominal Current: 4A Protection Rating: IP67 Contact Resistance: : RoHS Part Number Number of Positions Coding Conductor Cross-Section (mm) Conductor Cross-Section (AWG) Cable Diameter (mm) Min. Max. Min. Max. Min. Max. M12 Straight Male Connector, Screw Connection A-standard M12 Straight Female Connector, Screw Connection A-standard CAN Bus T-Connectors Robust shielded design Space-saving compact design Standardized interfaces -20 C to +90 C 60V Screw Connection: Female M12 connector to male M12 connector and female M12 connector Nominal Current: 4A Coding: A-standard Contact Resistance: Protection Rating: IP65/IP67 : RoHS Photographs are not to scale and are not true representations of the products in question. 188 Part Number Number of Pins Coding Nominal Voltage Nominal Current Standard Pack M12 T-Connector A-standard 60V 4A 5

35 CAN Bus CAN Bus Termination Resistor Robust design Standardized interfaces Space-saving compact design -25 C to +90 C Coding: A-standard 60V Protection Rating: IP65/IP67/IP69K Nominal Current: 4A : RoHS Number of Part Number Coding Nominal Voltage Nominal Current Standard Pack Positions M12 Straight Male Connector with Integrated Termination Resistor A-standard 60V 4A 5 Photographs are not to scale and are not true representations of the products in question. 189

36 BUS LD/LD FD P BUS LD BUS LD FD P BUS Long Distance (LD) cables are built after the RS-422 and protection. Recommended Applications Bus systems such as Modbus, SUCOnet P, Modulink P, VariNet-P; dry or tracks and moving machine parts Stationary Construction Conductors: Stranded bare copper Insulation: Polyethylene Shielding: braid Jacket: Violet PVC Continuous Flex Construction Conductors: Stranded bare copper Insulation: Polyethylene Shielding: braid Jacket: Violet polyurethane RS485/RS422 Maximum EMI protection PUR jacket resistant to tear, abrasion & mineral oils Flexible for ease of routing Cable Attributes See attribute list by part number on page 159 OIL FLAME MOTION MECHANICAL Similar Cables BUS PB MS-SC: page 528 Minimum Bend Radius: - Stationary cables: 8 x cable diameter - for installation: 6 x cable diameter - Stationary cables: -40 C to +80 C - for installation: -40 C to +80 C Characteristic Impedance: Nominal Capacitance: 18 pf/ft (800 Hz) Color Code: DIN 47100: Chart 8, page Pair 1: White & brown - Pair 2: Green & yellow - Pair 3: Gray & pink : UL: CM X (see below) Canada: CSA CMX (see below) 250V Recommended Section. Photographs are not to scale and are not true 190 Part Number Jacket Type Conductor Description Nominal Outer Diameter (AWG/Pair) (inches) (mm) (lbs/mft) (lbs/mft) MS-SC Stationary PVC 24 AWG/1pr PVC UL/CSA CMX 24 AWG/1pr PVC 24 AWG/2pr PVC 24 AWG/3pr Continuous Flex PUR 24 AWG/1pr PUR UL/CSA CMX 24 AWG/1pr PUR 24 AWG/2pr PUR UL/CSA CMX 24 AWG/2pr PUR 24 AWG/3pr PUR UL/CSA CMX 24 AWG/3pr

37 AS-Interface BUS ASi BUS ASi BUS ASi BUS ASi to larger conductor cross-sections. Recommended Applications Construction Stranded tinned copper technology with higher power demand can be connected to the Cable Attributes OIL Similar Cables Continuous Flex Cable Minimum Bend Radius: during installation: Peak Voltage: Test Voltage: Characteristic Impedance: Nominal Capacitance: Color Code: : Part Number Conductor Description Jacket Color Application Photographs are not to scale and are not true representations of the products in question. (lbs/mft) PVC Jacket Yellow EPDM Rubber Jacket Yellow Yellow TPE Jacket Yellow Red 19 (lbs/mft) 191

38 BUS ASi FD designed for data and power transfer between simple I/O devices on the and has a halogen-free PUR or oil-resistant TPE jacket. Recommended Applications data and power transmission between sensors, actuators, slaves, repeaters and master BUS ASi FD BUS ASi FD Construction Conductors: Stranded tinned copper Insulation: Polyurethane or TPE Jacket: Polyurethane or TPE AS-Interface Data and power transmission in one cable Quick connections to ASi-module due to piercing technology PUR-jacketed version is halogen-free and highly oil-resistant BUS ASi FD LD (Long Distance) allows even longer cable runs between modules Cable Attributes See attribute list by part number on page 159 OIL FLAME MOTION MECHANICAL Minimum Bend Radius: - for stationary use: 12 mm Similar Cables BUS ASi Test Voltage: Characteristic Impedance: Strain Relief: page V DIX -ASi: page PUR: - TPE: -40 C to +105 C -30 C to +105 C Peak Voltage: 300V Nominal Capacitance: Color Code: 24 pf/ft Blue & brown : UL: AWM (except & ) Canada: c(ru) AWM (except & ) Additional: ASi RoHS Part Number Approval Conductor Description Jacket Color Application (lbs/mft) (lbs/mft) PUR, FRNC, Halogen-Free Jacket UL/CSA AWM 2 x 16 AWG Yellow Data & power transmission UL/CSA AWM 2 x 16 AWG Black Transmission of 30V DC auxiliary power x 14 AWG Yellow Long distance, data & power transmission x 14 AWG Black Long distance, transmission of 30V DC auxiliary power TPE Jacket UL/CSA AWM 2 x 16 AWG Yellow Data & power transmission UL/CSA AWM 2 x 16 AWG Black Transmission of 30V DC auxiliary power Photographs are not to scale and are not true representations of the products in question. 192

39 AS-Interface DIX-ASi Cable Bushings for ASi Bus Cable; PG & Metric PG: page 502 Metric: page 502 Materials: NBR -40 C to +100 C Protection Class: IP54 IP68, 5 bar Color: Black (RAL 9005) : CE & RoHS Part Number Thread Type & Size Standard Pack Size DIX-ASi: PG PG DIX-ASi: Metric M20 50 Photographs are not to scale and are not true representations of the products in question. 193

40 BUS BlueFlex BUS BlueFlex BUS BlueFlex is designed for use in Rockwell/Allen Bradley DH, DH+, and Remote I/O networks. BlueFlex is constructed to withstand Data Highway Construction Conductors: Finely stranded tinned copper conductors Insulation: Shielding: braid (85% coverage) Jacket: Blue PVC Recommended Applications gauges; barcode readers; drives and operator interfaces. Signal integrity in continuous motion applications Flame- and oil-resistant jacket Flexible for ease of routing Cable Attributes, see page 659 OR-01 FR-02 CF-01 MP-01 OIL FLAME MOTION MECHANICAL MS-SC: page 528 Minimum Bend Radius: - for stationary use: 5 x cable diameter Characteristic Impedance: Nominal Capacitance: 17 pf/ft -20 C to +80 C Color Code: Blue/natural Test Voltage: 300V 3000V : UL: AWM 2661 Additional: RoHS Part Number Conductor Description Nominal Outer Diameter (AWG/Pair) (inches) (mm) (lbs/mft) (lbs/mft) MS-SC 3649FD 20 AWG/1pr Recommended Section. Photographs are not to scale and are not true 194