EX-10 SERIES Ver.2. Ultra-slim Photoelectric Sensor. Amplifier built-in extraordinarily small and slim size. Ver.2.

Transcription

1 319 PHOTO PHOTO Utra-sim Photoeectric Sensor EX- SERIES Ver.2 Reated Information Ver.2 Genera terms and conditions... F-17 Gossary of terms / Genera precautions... P.1359~ / P.145 Sensor seection guide... P.23~ Korea s S-mark... P.14 Conforming to EMC Directive (Excuding EX-15 /17 ) Certified (Some modes ony) Recognition MEASURE CONTRO panasonic-eectric-works.net/sunx PNP output type avaiabe buit-in extraordinariy sma and sim size Smaest body, just mm.13 in thick It can be mounted in a very sma space as its size is just W H1 D mm W H.571 D.13 in (thru-beam, front sensing type). Fexibe mounting The diffuse refective type sensor is front sensing and is so thin that it gives an impression of being just pasted on the mounting base. The thru-beam type is avaiabe as front sensing type, as we as, side sensing type, aowing fexibe mounting. Thru-beam Front sensing type Side sensing type Diffuse refective Front sensing type separated EX- -S2 RT-6 BASIC PERFORMANCE Eectric power saving * The EX- series achieves reductions in power consumption of up to 65 %. These sensors contribute to environmenta friendiness. * Effective from production in October 2. A maximum 35 % reduction compared to conventiona sensors High-speed response time:.5 ms The sensor is suitabe for detecting sma and highspeed traveing objects.

2 Utra-sim Photoeectric Sensor EX- SERIES Ver.2 32 APPICATIONS Verifying position of PCBs Detecting ICs Detecting PCB rack EX-19 Transparent stick IC EX-15 EX-14 Detecting wafer cassette Detecting thin ring Checking for absence of capacitor in tray EX-14 PHOTO PHOTO MEASURE EX-14 EX-13E CONTRO BASIC PERFORMANCE Minimum sensing object: ø1 mm ø.39 in EX-, EX-E, EX-15 and EX-15E are incorporated with ø1 mm ø.39 in sit masks so that ø1 mm ø.39 in, or more, object can be detected. Hence, they are suitabe for precise positioning or sma s detection. Background suppression EX-(E), EX-15(E) ong sensing range: 1 m 1 ft A sensing range of 1 m 1 ft has been reaized with a sim size of just mm.13 in. It can be used to detect even wide IC trays. 1 m 1 ft EX-19 EX-14 Hardy affected by background Even a specuar background separated by mm in, or more, is not detected. (However, the background shoud be directy opposite. A spherica or curved background may be detected.) ENVIRONA RESISTANCE Incorporated an inverter countermeasure circuit * The EX- series become significanty stronger against inverter ight and other extraneous ight. * Effective from production in October 2. Background Fuorescent ight tube mm in Back object reiaby detected It can reiaby detect dark coor objects since it is convergent refective type. Waterproof IP67 The sensor can be hosed down because of its IP67 construction and the non-corrosive stainess stee mounting bracket. Note: However, take care that if it is exposed to water spashes during operation, it may detect a water drop itsef. Bending durabiity Fexibe cabe type EX- -R is avaiabe. It is most suitabe for moving s, such as robot arm, etc. The best distance is approx. mm in from the object. EX- -R separated EX- -S2 RT-6

3 321 Utra-sim Photoeectric Sensor EX- SERIES Ver.2 PHOTO PHOTO MEASURE CONTRO MOUNTING / SIZE Mountabe with M3 screws Non-corrosive stainess stee type mounting bracket is aso avaiabe. MS-EX-1 [Cod roed carbon stee (SPCC)] MS-EX- [Stainess stee (SUS34)] mounting bracket for the front sensing type Red beam makes beam aignment easy The red ED beam projected from the emitter heps you to aign the sensor heads. FUNCTIONS M3 screws Bright 2-coor indicator A convenient 2-coor indicator has been incorporated in the miniature body. MS-EX-2 [Cod roed carbon stee (SPCC)] MS-EX-12 [Stainess stee (SUS34)] mounting bracket for the side sensing type M3 screws VARIETIES Operation mode switch MS-EX-3 [Cod roed carbon stee (SPCC)] MS-EX-13 [Stainess stee (SUS34)] (-shaped mounting bracket) M3 screws EX-15 /17 Thru-beam type sensor incorporated with an operation mode switch on the bifurcation is aso avaiabe. It heps you to test the operabiity before start-up. 2-coor indicator Orange: Red: Operation indicator Green: Stabiity indicator Operation mode switch Operation indicator (Orange) Even for the thru-beam type sensor, ony three wires have to be connected. OTHERS separated EX- ess resources used * Based on environmenta considerations, simpified packaging is used in order to reduce waste. In addition, the bag is made from poyethyene which produces no toxic gases even when burned. * Effective from production in October 2. -S2 RT-6

4 Utra-sim Photoeectric Sensor EX- SERIES Ver ORDER GUIDE Type Appearance Sensing range 15 mm 5.96 in Mode No. (Note 2) EX-A EX-B Output operation Output Front sensing 5 mm in 1 m 1 ft EX-13A EX-13B EX-19A EX-19B NPN output Thru-beam Side sensing With operation mode switch on the bifurcation With operation mode switch on the bifurcation 15 mm 5.96 in EX mm 5.96 in 5 mm in EX-17 5 mm in EX-EA EX-EB EX-13EA EX-13EB 15 mm 5.96 in EX-15E 5 mm in EX-17E Switchabe either or Switchabe either or NPN open-coector transistor CONTRO Convergent refective (Diffused beam type) Front sensing 2 to 25 mm.79 to.94 in (Note 1) (Convergent point: mm in) EX-14A EX-14B PNP output Thru-beam Convergent refective (Diffused beam type) Front sensing Side sensing Front sensing 15 mm 5.96 in 15 mm 5.96 in 5 mm in 1 m 1 ft 5 mm in 2 to 25 mm.79 to.94 in (Note 1) (Convergent point: mm in) EX-A-PN EX-B-PN EX-13A-PN EX-13B-PN EX-19A-PN EX-19B-PN EX-EA-PN EX-EB-PN EX-13EA-PN EX-13EB-PN EX-14A-PN EX-14B-PN PNP open-coector transistor separated NOTE: Mounting bracket is not suppied with the sensor. Pease seect from the range of optiona sensor mounting brackets (six types). Notes: 1) The sensor does not detect even a specuar background if it is separated by mm in or more. (However, the background shoud be directy opposite. A spherica or curved background may be detected.) 2) The mode No. with P shown on the abe affixed to the thru-beam type sensor is the emitter, D shown on the abe is the receiver. (e.g.) of EX-A: EX-P, of EX-A: EX-AD EX- -S2 RT-6

5 323 Utra-sim Photoeectric Sensor EX- SERIES Ver.2 ORDER GUIDE Fexibe cabe type Fexibe cabe type is aso avaiabe for NPN output type. (excuding sensor with operation mode switch on the bifurcation EX-15 /17 ) When ordering this type, suffix -R to the mode No. (e.g.) Fexibe cabe type of EX-A is EX-A-R. 5 m ft cabe ength type 5 m ft cabe ength type (standard: 2 m ft) is aso avaiabe for NPN output type. (excuding fexibe cabe type) When ordering this type, suffix -C5 to the mode No. (e.g.) 5 m ft cabe ength type of EX-A is EX-A-C5. Designation Mode No. Description Sensor mounting bracket MS-EX-1 MS-EX- MS-EX-1 Mounting bracket for the front sensing type sensor [Cod roed carbon stee (SPCC)] (The thru-beam type sensor needs two brackets.) MS-EX-2 Mounting bracket for the side sensing type sensor [Cod roed carbon stee (SPCC)] (The thru-beam type sensor needs two brackets.) CONTRO separated Sensor mounting bracket Sit mask Sensor checker (Note) Mounting screw MS-EX-3 MS-EX- MS-EX-12 MS-EX-13 Sit on one side OS-EX-12 (Sit size ø1.2 mm ø.47 in) Sit on both sides Sit on one side OS-EX-15 (Sit size ø1.5 mm ø.59 in) Sit on both sides OS-EXE-12 (Sit size ø1.2 mm ø.47 in) CHX-SC2 MS-M2 -shaped mounting bracket sensor [Cod roed carbon stee (SPCC)] (The thru-beam type sensor needs two brackets.) Mounting bracket for the front sensing type sensor [Stainess stee (SUS34)] (The thru-beam type sensor needs two brackets.) Mounting bracket for the side sensing type sensor [Stainess stee (SUS34)] (The thru-beam type sensor needs two brackets.) -shaped mounting bracket [Stainess stee (SUS34)] (The thru-beam type sensor needs two brackets.) Sit on one side Sit on both sides Sensing range: 6 mm in [EX-19 ] 25 mm 9.43 in [EX-13, EX-17 ] Min. sensing object: ø2 mm ø.79 in Sensing range: 4 mm in [EX-19 ] 2 mm 7.74 in [EX-13, EX-17 ] Min. sensing object: ø1.2 mm ø.47 in Sensing range: mm 396 in [EX-19 ] 35 mm 13.7 in [EX-13 ] Min. sensing object: ø2 mm ø.79 in Sensing range: 5 mm in [EX-19 ] 3 mm. in [EX-13 ] Min. sensing object: ø1.5 mm ø.59 in Sensing range: 25 mm 9.43 in [EX-13E, EX-17E ] Min. sensing object: ø2 mm ø.79 in Sensing range: 2 mm 7.74 in [EX-13E, EX-17E ] Min. sensing object: ø1.2 mm ø.47 in It is usefu for beam aignment of thru-beam type sensors. The optimum receiver position is given by indicators, as we as an audio signa. Mounting screws with washers (5 pcs. ot). It can mount securey as it is spring washer attached. Materia: Cod roed carbon stee (SPCC) (Uni-chrome pated) Two M2 (ength 4 mm.157 in) pan head screws are attached. MS-EX-2 Materia: Cod roed carbon stee (SPCC) (Uni-chrome pated) Two M2 (ength mm in) pan head screws are attached. MS-EX-3 Materia: Stainess stee (SUS34) Two M2 (ength 4 mm.157 in) pan head screws [stainess stee (SUS34)] are attached. MS-EX-12 Materia: Stainess stee (SUS34) Two M2 (ength mm in) pan head screws [stainess stee (SUS34)] are attached. MS-EX-13 Note: Refer to the sensor checker CHX-SC2 pages for detais. EX- -S2 Sit mask OS-EX-12 OS-EX-15 OS-EXE-12 Exampe of mounting (OS-EXE-12) Tighten aong with the sensor mounting bracket. Sensor checker CHX-SC2 POWER Sensor checker CHX-SC2 EVE Materia: Cod roed carbon stee (SPCC) (Uni-chrome pated) Two M2 (ength 4 mm.157 in) pan head screws, and two M2 (ength mm in) pan head screws are attached. Materia: Stainess stee (SUS34) Two M2 (ength 4 mm.157 in) pan head screws [stainess stee (SUS34)] and two M2 (ength mm in) pan head screws [stainess stee (SUS34)] are attached. RT-6

6 Utra-sim Photoeectric Sensor EX- SERIES Ver SPECIFICATIONS Convergent refective Thru-beam Type (Diffused beam type) Thru-beam with operation mode switch on bifurcation Front sensing Side sensing Front sensing Side sensing Front sensing Front sensing Front sensing Side sensing Front sensing Side sensing Mode No. EX-A(-PN) EX-EA(-PN) EX-13A(-PN) EX-13EA(-PN) EX-19A(-PN) EX-14A(-PN) EX-15 EX-15E EX-17 EX-17E Item (Note 2) EX-B(-PN) EX-EB(-PN) EX-13B(-PN) EX-13EB(-PN) EX-19B(-PN) EX-14B(-PN) (Note 3) (Note 3) (Note 3) (Note 3) 2 to 25 mm.79 Sensing range 15 mm 5.96 in 5 mm in 1 m 1 ft to.94 in (Note 4) (Conv. point: mm in) 15 mm 5.96 in 5 mm in Min. sensing object ø1 mm ø.39 in opaque object (Competey beam interrupted object) Setting distance between emitter and receiver: 15 mm 5.96 in ø2 mm ø.79 in opaque object (Competey beam interrupted object) Setting distance between emitter and receiver: 5 mm in ø2 mm ø.79 in opaque object Competey beam interrupted object Setting distance between emitter and receiver: 1 m 1 ft ø.1 mm ø.4 in copper wire Competey beam interrupted object Setting distance: mm in Hysteresis 15 % or ess of operation distance (Note 4) ø1 mm ø.39 in opaque object (Competey beam interrupted object) Setting distance between emitter and receiver: 15 mm 5.96 in Repeatabiity (perpendicuar to sensing axis).5 mm.2 in or ess.1 mm.4 in or ess.5 mm.2 in or ess Suppy votage 12 to 24 V DC ± % Rippe P-P % or ess Current consumption : ma or ess, : ma or ess 13 ma or ess 25 ma or ess Output <NPN output type> <PNP output type> NPN open-coector transistor PNP open-coector transistor Maximum sink current: 5 ma Maximum source current: 5 ma Appied votage: 3 V DC or ess (between output and V) Appied votage: 3 V DC or ess (between output and +V) Residua votage: 2 V or ess (at 5 ma sink current) Residua votage: 2 V or ess (at 5 ma source current) 1 V or ess (at 16 ma sink current) 1 V or ess (at 16 ma source current) ø2 mm ø.79 in opaque object (Competey beam interrupted object) Setting distance between emitter and receiver: 5 mm in NPN open-coector transistor Maximum sink current: ma Appied votage: 3 V DC or ess (between output and V) Residua votage: 2 V or ess (at ma sink current) 1 V or ess (at 16 ma sink current) Utiization category DC-12 or DC-13 Short-circuit protection Response time Incorporated.5 ms or ess Operation indicator Orange ED (ights up when the output is ON) Orange ED (ights up when the output is ON), ocated on the bifurcation Incident beam indicator Stabiity indicator Environmenta resistance Green ED (ights up under stabe ight received condition or stabe dark condition) Red ED (ights up under ight received condition), ocated on the receiver Green ED (ights up under stabe ight received condition or stabe dark condition), ocated on the receiver Poution degree 3 (Industria environment) Protection IP67 (IEC) Ambient temperature 25 to +55 C 13 to +131 F (No dew condensation or icing aowed), Storage: 3 to +7 C 22 to +15 F Ambient humidity Ambient iuminance 35 to 5 % RH, Storage: 35 to 5 % RH Incandescent ight: 3, x at the ight-receiving face EMC EN Votage withstandabiity Insuation resistance Vibration resistance Shock resistance Emitting eement Materia Cabe (Note 5) 1, V AC for one min. between a suppy terminas connected together and encosure 2 MΩ, or more, with 25 V DC megger between a suppy terminas connected together and encosure to 5 Hz frequency, 3 mm. in ampitude in X, Y and Z directions for two hours each 5 m/s 2 acceeration (5 G approx.) in X, Y and Z directions for three times each Red ED (Peak emission waveength: 6 nm.27 mi, moduated) Encosure: Poyethyene terephthaate ens: Poyayate.1 mm 2 3-core (thru-beam type emitter: 2-core) cabtyre cabe, 2 m ft ong Encosure: Poyethyene terephthaate ens: Poyayate, Bifurcation: Poyayate.2 mm 2 3-core cabtyre cabe, 2 m ft ong (beyond bifurcation; from emitter / receiver to bifurcation:.5 m 1.64 ft ong) Cabe extension Extension up to tota 5 m 164 ft is possibe with.3 mm 2, or more, cabe (thru-beam type: emitter and receiver). Extension up to tota m 32 ft is possibe with.3 mm 2, or more, cabe. Weight Net weight (each emitter and receiver): 2 g approx., Gross weight: 6 g approx. Net weight: 2 g approx. Gross weight: 4 g approx. Net weight: 55 g approx., Gross weight: g approx. Accessories Mounting screws: 1 set Mounting screws: 1 set Mounting screws: 1 set, Adjusting screwdriver: 1 pc. Notes: 1) Where measurement conditions have not been specified precisey, the conditions used were an ambient temperature of +23 C F. 2) Mode Nos. having the suffix -PN are PNP output type. 3) Either or can be seected by the operation mode switch (ocated on the bifurcation). 4) The sensing range and the hysteresis of convergent refective type sensor are specified for white non-gossy paper (5 5 mm in) as the object. 5) The fexibe cabe type (mode Nos. having suffix -R ) has a.1 mm 2 3-core (thru-beam type emitter: 2-core) fexibe cabtyre cabe, 2 m ft ong. CONTRO separated EX- -S2 RT-6

7 325 Utra-sim Photoeectric Sensor EX- SERIES Ver.2 I/O CIRCUIT AND WIRING DIAGRAMS EX- EX-13 EX-19 EX-14 NPN output type separated I/O circuit diagram Wiring diagram D1 Coor code (Brown) +V Sensor circuit Tr ZD D2 (Back) Output (Note) (Bue) V 5 ma max. oad + 12 to 24 V DC ± % Brown oad Back (Note) Bue + 12 to 24 V DC ± % CONTRO Interna circuit Users circuit Note: The emitter of the thru-beam type sensor does not incorporate the output. Symbos D1: Reverse suppy poarity protection diode D2: Reverse output poarity protection diode ZD: Surge absorption zener diode Tr : NPN output transistor EX- -PN EX-13 -PN EX-19 -PN EX-14 -PN I/O circuit diagram Coor code (Brown) +V Note: The emitter of the thru-beam type sensor does not incorporate the back wire. Wiring diagram PNP output type Sensor circuit Tr D1 ZD D2 5 ma max. (Back) Output (Note) oad (Bue) V 12 to 24 V DC ± % Interna circuit Users circuit Note: The emitter of the thru-beam type sensor does not incorporate the output. Symbos D1: Reverse suppy poarity protection diode D2: Reverse output poarity protection diode ZD: Surge absorption zener diode Tr : PNP output transistor + Brown Back (Note) Bue oad 12 to 24 V DC ± % Note: The emitter of the thru-beam type sensor does not incorporate the back wire. + EX- -S2 RT-6

8 Utra-sim Photoeectric Sensor EX- SERIES Ver I/O CIRCUIT AND WIRING DIAGRAMS EX-15 EX-15E EX-17 EX-17E EX-17W I/O circuit diagram Sensor circuit Tr D1 ZD Interna circuit D2 Coor code (Brown) +V (Back) Output Users circuit oad ma max. (Bue) V Symbos D1: Reverse suppy poarity protection diode D2: Reverse output poarity protection diode ZD: Surge absorption zener diode Tr : NPN output transistor + 12 to 24 V DC ± % NPN output type EX-15, EX-15E, EX-17, EX-17E wiring diagram Brown Back Bue oad + 12 to 24 V DC ± % SENSING CHARACTERISTICS (TYPICA) CONTRO A modes Thru-beam type Excess gain Correation between setting distance and excess gain 5 5 EX-13 EX-17 EX- EX , Excess gain 5 5 EX Setting distance (m ft) separated EX- -S2 RT-6

9 327 Utra-sim Photoeectric Sensor EX- SERIES Ver.2 SENSING CHARACTERISTICS (TYPICA) separated CONTRO EX- EX- EX-E EX-15 EX-15E Parae deviation EX- EX-15 EX- EX-15 EX-E EX-15E EX-E EX-15E Operating point (mm in) Anguar deviation EX-13 EX-13E EX-17 EX-17E EX- EX-15 EX-E EX-15E θ θ EX- EX-E EX-15 EX-15E 2 2 Operating ange θ ( ) Parae deviation Anguar deviation Parae deviation with sit masks (ø1.2 mm ø.47 in) EX-13 EX-17 EX-13E 4 EX-17E EX-13 EX-13E EX-17 EX-17E Operating point (mm in) EX EX-13 EX-17 4 EX-13E EX-17E 2 θ θ 7.74 EX-13 EX-13E EX-17 EX-17E 2 2 Operating ange θ ( ) EX-13 /17 Sit on one side EX-13 /17 Sit on both sides EX-13E /17E Sit on one side EX-13E /17E Sit on both sides Operating point (mm in) Parae deviation Anguar deviation Parae deviation with sit masks (ø1.2 mm ø.47 in) 1, Operating point (mm in) , θ Operating ange θ ( ) Sit on both sides Sit on one side Operating point (mm in) Thru-beam type Thru-beam type Parae deviation with sit masks (ø1.5 mm ø.59 in) Sit on one side or both sides Sit on one side, sensing range: 35 mm 13.7 in Sit on both sides, sensing range: 3 mm.1 in Operating point (mm in) Thru-beam type Parae deviation with sit masks (ø1.5 mm ø.59 in) 1, Sit on one side Sit on both sides Operating point (mm in) *Optica properties of side sensing types (EX-E/13E/15E/17E) Due to the optica properties of side sensing types, note that sensing may be affected if mutipe sensors are positioned in such a way that optica axes intersect as shown in the diagram beow or more 1 -S2 RT Beam from 1 may be caught by There is no probem when sensors are instaed in parae (athough the distance between sensors shoud be 2 or more).

10 Utra-sim Photoeectric Sensor EX- SERIES Ver.2 32 SENSING CHARACTERISTICS (TYPICA) EX-14 Convergent refective type Sensing range (mm in) Sensing fieds Horizonta (eft and right) direction mm.276 in 5 5 mm in Non-gossy paper White N Operating point (mm in) Vertica (up and down) direction White 5 5 mm in Non-gossy paper 7.75 N4 mm.35 in Down Center Up Operating point (mm in) Correation between ightness and sensing range Sensing region N2 N4 N6 N Dark ightness ight N1 N2 N3 N4 N5 N6 N7 N N9 Distance to convergent point The sensing region (typica) is represented by obique ines in the eft figure. However, the sensitivity shoud be set with enough margin because of sight variation in products. ightness shown on the eft may differ sighty from the actua object condition. PRECAUTIONS FOR PROPER Mounting In case of mounting on tapped hoes (Unit: mm in) Side sensing Never use this product as a sensing device for personne protection. In case of using sensing devices for personne protection, use products which meet aws and standards, such as OSHA, ANSI or IEC etc., for personne protection appicabe in each region or country. Front sensing Sensing range (mm in) Correation between materia (5 5 mm in) and sensing range Back circuit board Back rubber sheet IC tray (Back) Gass epoxy printed circuit board (Green masked surface) Ceramic circuit board White non-gossy paper Stainess stee pate Auminum pate (Hair ine) Auminum-evaporated mirror Distance to convergent point The bars in the graph indicate the sensing range (typica) for the respective materia. However, there is a sight variation in the sensing range depending on the product. Further, if there is a refective object (conveyor, etc.) in the background of the sensing object, since it affects the sensing, separate it by more than twice the sensing range shown in the eft graph. Refer to Genera precautions. Operation mode switch (EX-15, EX-15E, EX-17 and EX-17E ony) Switch position Operation mode switch : D: Operation indicator (Orange) ights up when the output is ON. Description CONTRO separated Sensing direction Attached screw [M2 (ength )] M hoe tapped, deep Sensing direction Attached screw [M2 (ength )] M hoe tapped, deep The tightening torque shoud be.2 N m or ess. In case of using attached screws and nuts (Unit: mm in) Side sensing Front sensing Fat washers Sensing Sensing direction direction Nuts Spring washers Attached screw Attached screw [M2 (ength )] [M2 (ength )] Thickness of Thickness of mounting pate: 2.79 or ess mounting pate: or ess The tightening torque shoud be.2 N m or ess. Others mode is set when the switch is turned fuy cockwise ( side). mode is set when the switch is turned fuy countercockwise (D side). Do not use during the initia transient time (5 ms) (EX-15, EX-15E, EX-17, EX-17E : ms) after the power suppy is switched on. Excess bending of the cabe or stress appied to the cabe may disconnect the interna ead wire. EX- -S2 RT-6

11 329 Utra-sim Photoeectric Sensor EX- SERIES Ver.2 DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downoaded from our website. EX-A EX-B EX-13A EX-13B EX-19A EX-19B Sensor Beamreceiving Stabiity indicator (Green) Operation indicator (Orange) ø2.2 ø.7 mounting hoes ø2.5 ø.9 cabe, 2 m ft ong Beamemitting ø2.2 ø.7 mounting hoes ø2.5 ø.9 cabe, 2 m ft ong CONTRO EX-EA EX-EB EX-13EA EX-13EB Sensor Beamemitting Stabiity indicator (Green) Operation indicator (Orange) Beamreceiving ø2.2 ø.7 mounting hoes ø2.5 ø.9 cabe, 2 m ft ong ø2.2 ø.7 mounting hoes ø2.5 ø.9 cabe, 2 m ft ong separated EX- -S2 RT-6 EX-15 EX ø2.2 ø.7 mounting hoes ø2.5 ø.9 cabes Operation indicator (Orange) Beam- Beamemitting receiving ø3. ø.15 cabe, 2 m ft ong.69 Sensor Stabiity indicator (Green) Incident beam indicator (Orange) ø2.2 ø.7 mounting hoes Operation mode switch EX-15E EX-17E ø2.2 ø.7 mounting hoes Beamemitting Sensor Stabiity indicator (Green) Incident beam indicator (Orange) Beamreceiving ø2.5 ø.9 cabes Operation indicator (Orange) ø3. ø.15 cabe, 2 m ft ong 2-ø2.2 ø.7 mounting hoes Operation mode switch

12 Utra-sim Photoeectric Sensor EX- SERIES Ver.2 33 DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downoaded from our website. EX-14A EX-14B Sensor Beamreceiving Beam-emitting Stabiity indicator (Green) Operation.13 indicator (Orange) ø2.2 ø.7 mounting hoes ø2.5 ø.9 cabe, 2 m ft ong MS-EX-1 t M thru-hoe threads ø3.4 ø.134 mounting hoes Materia: Cod roed carbon stee (SPCC) (Uni-chrome pated) Two M2 (ength 4 mm.157 in) pan head screws are attached. Assemby dimensions Mounting drawing with EX-14 t Beamemitting Beamreceiving Sensor mounting bracket (Optiona) 2.77 (.7) 7.6 (.2) (4.9) (.193).13 (.) (.346) ø3.4 ø.134 mounting hoes CONTRO MS-EX-2 t Assemby dimensions Mounting drawing with EX-E and EX-13E Sensor mounting bracket (Optiona) separated t (2.3) (.91) 2-M thru-hoe threads Materia: Cod roed carbon stee (SPCC) (Uni-chrome pated) Two M2 (ength mm in) pan head screws are attached (1.3) (.51).25. Beamreceiving (7.45) (.293) EX- -S2 RT-6

13 331 Utra-sim Photoeectric Sensor EX- SERIES Ver.2 DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downoaded from our website. CONTRO MS-EX-3 t M thru-hoe threads Materia: Cod roed carbon stee (SPCC) (Uni-chrome pated) Two M2 (ength 4 mm.157 in) pan head screws and two M2 (ength mm in) pan head screws are attached. MS-EX- t M thru-hoe threads Materia: Stainess stee (SUS34) Two M2 (ength 4 mm.157 in) pan head screws [stainess stee (SUS34)] are attached. Sensor mounting bracket (Optiona) Assemby dimensions Mounting drawing with EX-14 (2.75) (.) (.7) (.2) Beamreceiving t Beam-emitting Beam-receiving..425 Assemby dimensions Mounting drawing with EX-14 t Beamemitting Sensor mounting bracket (Optiona) (9.3) (.366) (.7) (.2) (4.9) (.193) separated EX- MS-EX-12 t Assemby dimensions Mounting drawing with EX-E and EX-13E t.47 Sensor mounting bracket (Optiona) (1.3) (.51) (2.3) (.91) (7.45) (.293) S2 RT-6 2-M thru-hoe threads Materia: Stainess stee (SUS34) Two M2 (ength mm in) pan head screws [stainess stee (SUS34)] are attached Beam receiving

14 Utra-sim Photoeectric Sensor EX- SERIES Ver DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downoaded from our website. MS-EX t M thru-hoe threads Materia: Stainess stee (SUS34) Two M2 (ength 4 mm.157 in) pan head screws [stainess stee (SUS34)] and two M2 (ength mm in) pan head screws [stainess stee (SUS34)] are attached. Sensor mounting bracket (Optiona) Assemby dimensions Mounting drawing with EX-14 (2.75) (.) Beam-emitting Beam-receiving (.7) (.2) t CONTRO separated EX- -S2 RT-6