Control Components (August 2015)

Size: px

Start display at page:

Download "Control Components (August 2015)"

Martina King
7 years ago
Views:

1 Control Components (August 2015) New Generation (G4) CNC 5hp (with exchange) New Generation (G4) CNC C-axis (with exchange) Call for special pricing Call for special pricing LCD Monitor with VGA Card (Replaces CRT Monitor ) VGA Card ISA VGA Card PCI LCD Monitor only $525 $95 $95 $430 G4 CNC Motherboard complete (with exchange) $475 NOTE: Must update G4 software if changing from fan to fanless mb G3 CNC Motherboard complete $595 AT Power Supply (G3 CNC) $75 ATX Power Supply (G4 CNC) $75 rp_control_components.doc pg 1 of 3

995-17-011 995-17-014 996-16-019 $525 $95 $95 $430 G4 CNC Motherboard complete (with exchange) 995-17-015 $475 NOTE: Must update G4 software if changing from fan

2 Control Components (August 2015) IP68 Medical Grade Keyboard Oil Resistant - Made in USA $295 Auxiliary Power Supply Kit For older G3 CNC only (Provides higher 12VDC for more reliable collet-closer operation) $50 OmniTurn Servo Amp, w/exchange $525 AMC Servo Amp, w/exchange (For old-style G2 & G3 CNC) $250 MC2 Exchange Refurbished MC2-B Exchange Refurbished $1,000 $1,000 Servo Motor Thermal Overload (G4 and late G3 CNC) $10 Thermal Overload w/heater (refurb) W43 Heater only (new) (G3 CNC pre-2007) $85 $45 12V Relay (3-pole) (Used everywhere except latest spindle-drive circuit board) $16 rp_control_components.doc pg 2 of 3

Refurbished MC2-B Exchange Refurbished 995-49-001 995-49-004 $1,000 $1,000 Servo Motor Thermal Overload (G4 and late G3 CNC) 995-15-015 $10 Thermal Overload w/heater (refurb) W43

3 Control Components (August 2015) Solid-state Hard Drive (For G3 or G4 CNC) $125 Monochrome Video Card (For G3 w/amber CRT Monitor) $82 OmniTurn Programming & Service Manual (Specify G3 or G4) $50 USB Floppy Drive Emulator (Provides USB compatibility for old-style CNC) $150 rp_control_components.doc pg 3 of 3

Programming & Service Manual (Specify G3 or G4) 999-59-001 $50 USB Floppy Drive Emulator

4 Control Panel Components (February 2014) Control On/Off Switch Assembly Control On/Off Switch Assembly (G4) $40 $40 Servo On Switch Assembly $40 Cycle Start Switch Assembly $40 Motion Stop Switch Assembly $40 Spindle Auto / Off Switch Assembly $40 Collet Open/Close Assembly (G4) C-Axis Jog Switch Assembly (G4) $40 $40 Spindle Override Pot (G3) Spindle Override Pot (G4) Feedrate Override Pot (G4) $20 $20 $20 Jog Switch Assembly $113 Emergency Stop Switch Assembly $40 rp_control_panel_components.doc pg 1 of 1

Open/Close Assembly (G4) C-Axis Jog Switch Assembly (G4) 995-12-202 995-12-203 $40 $40 Spindle Override Pot (G3) Spindle Override Pot (G4) Feedrate Override Pot

5 Palm Box Components (August, 2015) Picture Description Part Number Price Complete Palm Box Assembly $350 Collet Open Button Assembly $25 Collet Close Button Assembly $25 Emergency Stop Push Button Assembly $40 Cycle Start Push Button Assembly $40 rp_palm_box_components.doc pg 1 of 1

Close Button Assembly 998-12-101 $25 Emergency Stop Push Button Assembly 998-12-104

6 X & Z Axis Components (June 2014) Linear way assembly: Includes 2 bearing block trucks 2 assemblies needed per axis X axis 10 travel 18 (460 mm) X axis 12 travel 21 (520 mm) Z axis 5 travel 11 (280 mm) Z axis 8 travel - 18 ( 460 mm) $425 $450 $425 $425 Bearing Block Trucks (Set of 2) $225 Ballscrew Only Ballscrew & Thrust Bearing $950 $1,130 Thrust Bearing Assembly $180 Motor Coupling, Helical $55 Motor Coupling, Huco $55 Axis Motors (MTE) One Year warranty $950 rp_x&z_axis_components.doc pg 1 of 1

Trucks (Set of 2) 992-08-012 $225 Ballscrew Only Ballscrew & Thrust Bearing 992-08-011 992-08-002 $950 $1,130 Thrust Bearing Assembly 992-08-003 $180 Motor

7 Spindle Drive and Motor Compartment Components July 2016 Spindle Encoder All Attachments (All GT s until 2007: see Direct-mount Encoder, below $475 Encoder Belt GT75 all attachments except HLV Encoder Belt GTJr $12 $12 Encoder Pulley (aluminum type) Encoder Side $60 Encoder Pulleys: Spindle Side GT75 & GTJr DSM, DV HSL HC, AHC, HNC $60 $60 $60 $60 Encoder Cable $44 Direct-mount Encoder, 5hp only (1/4 shaft) $250 Direct-mount Encoder, 5hp only (3/8 shaft) $250 Old 5hp Motor Pulley Only (PolyVee) $125 Motor Pulley Kit 5hp/CAX: GT-75/Jr $500 Motor Pulley Kit 5hp/CAX: Attachment $750 rp_spindle_drive_components.doc pg 1 of 3

193-22-001 093-22-002 293-22-001 $60 $60 $60 $60 Encoder Cable 995-07-003 $44 Direct-mount Encoder, 5hp only (1/4 shaft) 995-16-105 $250 Direct-mount Encoder, 5hp only (3/8 shaft) 995-16-103 $250

8 Spindle Drive and Motor Compartment Components July 2016 PolyV 310J10 Belt PolyV 290J10 Belt PolyV 360J10 Belt PolyV 300J10 Belt PolyV 380J10 Belt Spindle Drive Belt C-Axis Cog Type (pre-2001/late 2000: slide s/n w/o PTI ) $36 $36 $36 $36 $36 For GT75 & GTJr (300H100) $25 Spindle Drive Belt 5hp/CAX Herringbone Type For GT-75 or GT-Jr $60 Dunham Collet Closer With Drawtube Dunham Collet Closer Complete $2,175 $2,625 Dunham Drawtube Only $250 Dunham Collet Closer Rebuild Kit: Dunham Seals Kit Dunham Bearings Only Bearings and Seals Disogrin Drawtube Seal A $65 $160 $225 $45 Spindle drives GT75/GTJr. Standard Inverter Attachment Standard Inverter C-axis, current, w/exchange $795 $795 $2,500 rp_spindle_drive_components.doc pg 2 of 3

GT-Jr 693-21-001 $60 Dunham Collet Closer With Drawtube Dunham Collet Closer Complete 693-08-200 693-09-100 $2,175 $2,625 Dunham Drawtube Only 693-08-211 $250 Dunham Collet Closer Rebuild Kit: Dunham

9 Spindle Drive and Motor Compartment Components July 2016 New Spindle Complete Cam Lock, w/exchange $3,500 Drawtube Plug Spindle $50 Brake Resistor: 5HP Inverter Drive (40 ohms 500W) Brake Resistor: C-Axis Yaskawa (8.5 ohms 500W) Brake Resistor: C-Axis Yaskawa Short Cycle (8.5 ohms 1000W) Brake Resistor: C-Axis Baumuller Short Cycle (15 ohms 1000W) $125 $125 $350 $350 rp_spindle_drive_components.doc pg 3 of 3

(8.5 ohms 500W) Brake Resistor: C-Axis Yaskawa Short Cycle (8.

10 Pneumatic Components (August 2016) Mac Single Solenoid Valve Only $62 Select this component to replace failed solenoid valve. Includes mounting screws and gasket. Mac Single Solenoid Valve w/manifold $105 Select this component to add solenoid valve to existing air-pack. Includes mounting tie-rods and gasket. Use cable p/n (below) for electrical connection. Mac Single Solenoid Valve w/flow-control $115 Select this component to replace obsolete solenoid valve with integral regulator. Same as except with flow-control and plug. Mac Single Solenoid Valve Complete $120 Select this component to add standalone solenoid valve. Includes manifold, end plate, fittings and 12V connector w/cable. Mac Double Solenoid Valve Only $100 Select this component to replace failed solenoid valve. Includes mounting hardware and gasket. Mac Double Solenoid Valve/manifold $116 Select this component to add solenoid valve to existing air-pack. Includes mounting tie-rods and gasket. Use cable p/n (below) for electrical connection. rp_pneumatic_components.doc pg 1 of 3

Use cable p/n 997-15-011 (below) for electrical connection. Mac Single Solenoid Valve w/flow-control 997-15-206 $115 Select this component to replace obsolete solenoid valve with integral regulator.

11 Pneumatic Components (August 2016) Mac Double Solenoid Complete $164 Select this component to add standalone solenoid valve. Includes manifold, end plate, fittings and 12V connector w/cable. Mac Solenoid Valve w/regulator No longer available: If air solenoid has failed, use above. If regulator has failed use , which is plus flow control. Mac Valve Connector and Cable $15 Select this component if you are adding additional station to existing air pack. Route cable to 12vdc source to actuate air valve. Six feet long. Festo Single Solenoid (12V) No longer available: Use Single Mac Festo Replacement To replace Festo air for pneumatic/manual collet closer: Use Dual Mac Single Replacement $131 $236 Festo Double Solenoid (12V) No longer available: Use Double Mac Festo Replacement $175 Main Regulator Assembly w/gauge $75 rp_pneumatic_components.doc pg 2 of 3

If regulator has failed use 997-15-206, which is 997-15-204 plus flow control.

12 Pneumatic Components (August 2016) Collet Closer Regulator Assembly $60 Main Regulator Plastic Bowl Main Regulator Zinc Bowl Filter Element $15 $20 $40 Air Lubricator Bowl Air Lubricator w/bracket & Fittings $35 $150 rp_pneumatic_components.doc pg 3 of 3

997-11-008 997-11-012 997-11-022 $15 $20 $40 Air Lubricator Bowl Air Lubricator

13 Additional Components March 2014 Z Axis Scale X Axis Scale $18 $18 Rubber way cover, 5 or 8 Travel (cut 8 to fit) $30 Bellows Cover for GT75 & GTJr (Accordion Way Cover) $205 M Function Diagnostic Console Very useful for trouble-shooting Your OmniTurn CNC! $275 Coolant Pump Only Coolant Pump Flange $235 $31 Bolt Down Kit To secure GT-75 or GT-Jr to floor when aligned with Zip Loader or bar feeder $115 rp_additional_components.doc pg 1 of 2

14 Additional Components March 2014 Collet Closer Air Switch Kit To inhibit Cycle Start if collet or chuck is not clamped $125 Parts Catcher Kit $750 Instant start, dual fluorescent Work Lamp Kit (includes Brackets) $150 Feet (GT75 & GTJr) Price for Four $56 Vibration Isolation Pad (GT75 & GTJr) Price for Four $68 PLC Kit 16 INPUTS & 14 OUTPUTS $1,095 rp_additional_components.doc pg 2 of 2

Brackets) 491-09-002 $150 Feet (GT75 & GTJr) Price for Four 691-13-001 $56 Vibration Isolation Pad (GT75 & GTJr)

Providing Answers For All Your Machine Tool Needs

Providing Answers For All Your Machine Tool Needs STANDARD FEATURES FANUC MXP-200FA CONTROL Spindle Features Body Structure POWERFUL 20 HP H / L SHIFTING SPINDLE MOTOR HARDENED & GROUND BOXWAY CONSTRUCTION