GPS Relevant. ISO-Standards

Transcription

1 R P L PS 8-Point Procedure A1 M A R L 60 7 ISO-Standards E 0,1 M R A F M 0,1 M R A E PS 8-Point Procedure A A -0,8/Rz 1, ,005 A -0,2 A 0, ± 0,2 E 0 M LP 4 A1 R -0,8/Rz 1, A1 A A C B PS Relevant P A1 232 ± 0,2 E D 0,005 D 0,005 A LP E D U A L ,005 E PS 8-Point Procedure LP UZ 60 7 UZ 4-0,2 A1 0 M PS 8-Point Procedure ,2 A1 eometrical Product Specifications (PS) order 25t Edition August 2013 A E 0,02 A C B F 0,1 M R A M -0,8/Rz 1,2 PS 8-Point Procedure A -0,2 R M L UZ P PS 8-Point Procedure 0,005-0,8/Rz 1,2 Per Bennic L ,005 E LP D P DK-3500 Vaerloese 0,02 A 0,005 PB Metrology Consulting Birkevej 11 Denmark C B F 232 ± 0,2 E E F D A1 0 M per@bennic.dk web: A 60 7

2 List of PS relevant ISO-standards Page 1 of 21 Introduction Tis document contains a table sowing a list of PS-relevant ISO-standards - status May Te standards are mentioned in te order of increasing s. Tis Edition 25 of te list replace te May 2013, 24 t edition. Canges in tis list are marked wit colour codes in te left column of te table (see te colours codes in te bottom of tis page). 21 documents ave ad a new status from te 24 t to te 25 t edition. Te list contains all PS relevant ISO standards in te following PS-matrix system categories: S S S Fundamental PS standards lobal PS standards eneral PS standards But te list is not complete and exaustive in te category: S Complementary PS standards A few process specific complementary standards are in te list. Te list also include standards concerning te drawing picture/views, not part of te PS matrix system. Te list contains more tan 250 standard documents. Te documents can be split up into tree types: - ISO standards wic are in force at te moment for te tolerancing of drawings and/or for te verification (measurement) of requirements given on drawings. - ISO standards witdrawn. Te list is far from complete for tis type. Te mentioned witdrawn standards are only given because tey are te most important for te interpretation of older drawings, and standards were te rules of interpretation are canged in later editions. - Working documents, not finalised, but expected to be stable in teir content and is expected to be publised wit tis content. Te table - its design and content Te columns contain te following information: Column #1 - Te designation of type sow te different type of ISO documents, e.g.: ISO ISO - standard Oter types of ISO documents tan ISO standards exist: ISO/TR (Tecnical Report) wit an informative and educational content, ISO/TS (Tecnical Specification) wit a content as a standard, but wit a sorter development time and a sorter lifetime before re or reconfirmation is needed, ISO/R (Recommendation) former designation for a standard. Tis designation is not used anymore for new standards. New documents or documents wit major cange of are marked wit colour in column #1 New status ISO 18 New or cange of status in te 15 t version - November 2011 ISO 12 New or cange of status in te 16 t version - January 2012 ISO 14 New or cange of status in te 17 t version - Marc 2012 ISO 19 New or cange of status in te 18 t version - April 2012 ISO 17 New or cange of status in te 19 t version - May 2012 ISO 33 New or cange of status in te 20 t version - August 2012 ISO 25 New or cange of status in te 21 t version - October t 2012 ISO 8 New or cange of status in te 22 t version - December t 2012 ISO 25 New or cange of status in te 23 rd version - February 2013 ISO 23 New or cange of status in te 24 t version - May 2013 ISO 21 New or cange of status in te 25 t version - August 2013

3 List of PS relevant ISO-standards Page 2 of 21 Column #2 - ISO (and CEN) documents ave a uniq for identification. A series of standards concerning te same s can ave te same, but will ten ave different part s. Column #3 - In tis column every document is designed to explain its present status: P T Te document is in force at te moment. Te document is witdrawn (Te cell in te table is darkened to make it more visible) WD, CD, DIS and FDIS is designations for ISO working documents in te different stages of development. Mentioned in te order tey appear in te development process: WD CD DIS FDIS UP Working document in a working group under an ISO Tecnical Committee. Te first sketc for te standard. Official proposal for te content. Ballot take place in te ISO Tecnical Committee Draft International Standards. Ballot take place in ISO - wit tecnical comments Final Draft International Standard. Ballot take place in ISO - wit editorial comments Under Publication Column #4 - Edition Te is not necessary uniq. Examples exist, were two documents wit te same ave te same edition. Te is a more safe and uniq identification. Working documents ave no edition in te table. Column #5 - of te document. Observe tat CEN standards based on ISO standards may ave a later date and tan te identical ISO standard. Column #6 - mont Column #7 - PS-matrix relation - Te relation to te PS-matrix system is identified by te following letters in te table (see figure 1): F B P M T U Fundamental PS standard lobal PS standard eneral PS standard Process specific complementary PS standard - eneral tolerances Macine element specific complementary PS standard - Tolerance systems for special geometries Not part of te PS-matrix system - Drawing picture/views Not part of te PS-matrix system - miscellaneous

4 List of PS relevant ISO-standards Page 3 of 21 F Fundamental PS standards lobal PS standards PS or related standards wic deal wit or ave inflnce on more or all PS standard cains eneral PS-Matrix 1. Linear size standards cain 2. Linear distance standards cain 3. Radius distance standards cain 4. Arc lengt standardscain 5. Angle size standards cain (tolerance in degrees) 6. Angle distance standards cain (tolerance in degrees) 7. Form of a line (independent of a datum) standards cain 8. Form of a line (dependent of a datum) standards cain 9. Form of a surface (independent of a datum) standards cain 10. Form of a surface (dependent of a datum) standards cain 11. Orientation standards cain 12. Location standards cain 13. Circular run-out standards cain 14. Total run out standards cain 15. Datum standard cains 16. Rougness profile standards cain 17. Waviness profile standards cain 18. Primary profile standards cain 19. Surface imperfection standards cain 20. Edges standards cain Complementary PS-Matrix Process specific eneral tolerance standards A1. Macining standards cain A2. Casting standards cain A3. Plastic moulding standards cain A4. Welding standards cain A5. Termal cutting standards cain A6. Coating standards cains Macine element specific tolerance standards B1. Screw tread standards cains B2. ears standards cains B3. Splines standards cains P M B Figure 1 - PS-matrix system ierarcy Column #8 - Te full title is given. Observe tat te designation eometrical Product Specifications (PS) in te tittle identifies te PS standards updated and modernised by ISO/TC 213.

5 List of PS relevant ISO-standards Page 4 of 21 ISO/R 1 T Standard reference temperature for industrial lengt measurements ISO 1 T B Standard reference temperature for industrial lengt measurements (witdrawn ) ISO 1 P B eometrical product specification (PS) - Standard reference temperature for geometrical product specification and verification ISO 3 P U Preferred s - Series of preferred s ISO 7-1 T ? M Pipe treads were pressure-tigt joints are made on te treads -- Part 1: Designation, dimensions and tolerances ISO 7-1 P M Pipe treads were pressure-tigt joints are made on te treads Part 1: Dimensions, tolerances and designation ISO 7-1 C1 P C M Pipe treads were pressure-tigt joints are made on te treads -- Part 1: Dimensions, tolerances and designation - Tecnical Corrigendum 1:2007 ISO 7-2 T ? M Pipe treads were pressure-tigt joints are made on te treads -- Part 2: Verification by means of limit gauges ISO 7-2 P M Pipe treads were pressure-tigt joints are made on te treads -- Part 2: Verification by means of limit gauges ISO 14 P M Straigt-sided splines for cylindrical safts wit internal centering Dimensions, tolerances and verification ISO 17 P U uide to te use of preferred s and of series of preferred s ISO/R 68 T ? ISO general purpose screw treads -- Basic profile ISO 68 T ? M ISO general purpose screw treads -- Basic profile ISO 68-1 P M ISO general purpose screw treads -- Basic profile -- Part 1: Metric screw treads ISO 68-2 P M ISO general-purpose screw treads -- Basic profile -- Part 2: Inc screw treads ISO/R 128 T ? T Tecnical drawings - general principles of presentation ISO 128 T T Tecnical drawings - general principles of presentation - witdrawn ISO P T Tecnical drawings - eneral principles of presentation - Part 1: Introduction and index ISO FDIS T Tecnical product documentation (TPD) -- eneral principles of presentation -- Part 15: Presentation of sipbuilding drawings ISO P T Tecnical drawings - eneral principles of presentation - Part 20: Basic conventions for lines ISO P T Tecnical drawings - eneral principles of presentation - Part 21: Preparation of lines for CAD systems ISO P T Tecnical drawings - eneral principles of presentation - Part 22: Basic conventions and applications for leader lines and reference lines ISO P T Tecnical drawings - eneral principles of presentation - Part 24: Lines on mecanical engineering drawings ISO FDIS T Tecnical drawings - eneral principles of presentation - Part 24: Lines on mecanical engineering drawings ISO P T Tecnical drawings - eneral principles of presentation - Part 25: Lines on sipbuilding drawings

6 List of PS relevant ISO-standards Page 5 of 21 ISO P T Tecnical drawings - eneral principles of presentation - Part 30: basic conventions for views ISO P T Tecnical drawings - eneral principles of presentation - Part 34: Views on mecanical engineering drawings ISO P T Tecnical drawings - eneral principles of presentation - Part 40: Basic conventions for cuts and sections ISO P T Tecnical drawings - eneral principles of presentation - Part 44: Sections on mecanical engineering drawings ISO P T Tecnical drawings - eneral principles of presentation - Part 50: Basic conventions for representing areas and cuts and sections ISO/TS P T Tecnical product documentation (TPD) -- eneral principles of presentation Part 71: Simplified representation for mecanical engineering drawings ISO 129 T Tecnical drawings - Dimensioning - eneral principles, definitions, metods of execution and special indications (witdrawn ) ISO P Tecnical drawings - Indication of dimensions and tolerances - Part 1: eneral principles ISO NP Tecnical drawings - Indication of dimensions and tolerances - Part 1: eneral principles ISO T eometrical Product Specifications (PS) - Indication of dimensions and tolerances - Part 2: Mecanical engineering drawings - Te content is moved before publication to ISO ISO CD Tecnical product documentation (TPD) -- Indication of dimensions and tolerances -- Part 2: Dimensioning of mecanical engineering drawings ISO FDIS T Tecnical product documentation (TPD) -- Indication of dimensions and tolerances -- Part 4: Dimensioning for sipbuilding drawings ISO T ? M Pipe treads were pressure-tigt joints are not made on te treads -- Part 1: Dimensions, tolerances and designation ISO T M Pipe treads were pressure-tigt joints are not made on te treads -- Part 1: Dimensions, tolerances and designation ISO P M Pipe treads were pressure-tigt joints are not made on te treads -- Part 1: Dimensions, tolerances and designation ISO T ? M Pipe treads were pressure-tigt joints are not made on te treads -- Part 2: Verification by means of limit gauges ISO P M Pipe treads were pressure-tigt joints are not made on te treads -- Part 2: Verification by means of limit gauges ISO/R 261 T ? M ISO general purpose metric screw treads -- eneral plan ISO 261 T ? M ISO general purpose metric screw treads -- eneral plan ISO 261 P M ISO general purpose metric screw treads -- eneral plan ISO/R 262 T ? M ISO general-purpose metric screw treads Selected sizes for screws, bolts and nuts ISO 262 T ? M ISO general-purpose metric screw treads Selected sizes for screws, bolts and nuts ISO 262 P M ISO general-purpose metric screw treads Selected sizes for screws, bolts and nuts ISO 263 P M ISO inc screw treads -- eneral plan and selection for screws, bolts and nuts -- Diameter range 0.06 to 6 in ISO 273 P U Fasteners -- Clearance oles for bolts and screws

7 List of PS relevant ISO-standards Page 6 of 21 ISO/R 286 T ISO system of limits and fits -- Part I : eneral, tolerances and deviations (witdrawn ) ISO T ISO system of limits and fits - Part 1: Bases of tolerances, deviations and fits. (witdrawn ) ISO P eometrical Product Specification (PS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits ISO Cor1 P eometrical product specifications (PS) -- ISO code system for tolerances on linear sizes -- Part 1: Basis of tolerances, deviations and fits Corrigendum 1:2013 ISO T ISO system of limits and fits - Part 2: Tables of standard tolerance grades and limit deviations for oles and safts (witdrawn ) ISO Cor 1 T ? ISO system of limits and fits - Part 2: Tables of standard tolerance grades and limit deviations for oles and safts - Corrigendum 1 (witdrawn ) ISO P eometrical Product Specification (PS) ISO code system for tolerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for oles and safts ISO Cor 1 P eometrical product specifications (PS) -- ISO code system for tolerances on linear sizes -- Part 2: Tables of standard tolerance classes and limit deviations for oles and safts Corrigendum 1:2013 ISO 296 T ? M Macine tools -- Self-olding tapers for tool sanks ISO 296 P M Macine tools -- Self-olding tapers for tool sanks ISO 297 T ? M 7/24 tapers for tool sanks for manual canging ISO 297 P M 7/24 tapers for tool sanks for manual canging ISO 370 T B Toleranced dimensions - Conversions from inces to millimetres and vice versa (witdrawn ) ISO/R 406 T ? Tecnical drawings -- Linear and angular tolerancing -- Indications on drawings ISO 406 T ? Tecnical drawings -- Linear and angular tolerancing -- Indications on drawings ISO 406 T Tecnical drawings - Tolerancing of linear and angular dimensions (te content will be included in ISO :2011) (witdrawn ) ISO/R 463 T Dial gauges reading 0,01 and 0,001 mm (witdrawn ) ISO 463 P eometrical Product Specifications (PS) Design and metrological caracteristics of mecanical dial gauges ISO 463 C1 P C eometrical Product Specifications (PS) - Dimensional measuring equipment - Design and metrological caracteristics of mecanical dial gauges TECHNI- CAL CORRIENDUM 1 ISO 463 C2 P C eometrical Product Specifications (PS) - Dimensional measuring equipment - Design and metrological caracteristics of mecanical dial gauges TECHNI- CAL CORRIENDUM 2 ISO 468 T Surface rougness - Parameters, teir vals and general rules for specifying requirements (witdrawn ) ISO 724 T ? M ISO metric screw treads -- Basic dimensions ISO 724 P M ISO general-purpose metric screw treads -- Basic dimensions ISO 724 Cor 1 P C M ISO general-purpose metric screw treads -- Basic dimensions - Corrigendum 1 ISO 725 T ISO inc screw treads -- Basic dimensions (witdrawn ) ISO 725 P M ISO inc screw treads -- Basic dimensions

8 List of PS relevant ISO-standards Page 7 of 21 ISO/R 965/I T ? M ISO general-purpose metric screw treads -- Tolerances -- Part I: Principles and basic data ISO T ? M ISO general-purpose metric screw treads -- Tolerances -- Part 1: Principles and basic data ISO P M ISO general-purpose metric screw treads -- Tolerances -- Part 1: Principles and basic data ISO Cor 1 P C M ISO general-purpose metric screw treads Tolerances -- Part 1: Principles and basic data Corrigendum 1 ISO FDIS M ISO general-purpose metric screw treads -- Tolerances -- Part 1: Principles and basic data ISO/R 965/II T ? M ISO general purpose metric screw treads -- Tolerances -- Part II: Limits of sizes for general purpose external and internal screw treads -- Medium quality ISO T ? M ISO general purpose metric screw treads -- Tolerances -- Part 2: Limits of sizes for general purpose external and internal screw treads -- Medium quality ISO P M ISO general purpose metric screw treads -- Tolerances -- Part 2: Limits of sizes for general purpose external and internal screw treads -- Medium quality ISO/R 965/III T ? M ISO general purpose metric screw treads -- Tolerances -- Part III: Deviations for constructional screw treads ISO T ? M ISO general purpose metric screw treads -- Tolerances -- Part 3: Deviations for constructional screw treads ISO P M ISO general purpose metric screw treads -- Tolerances -- Part 3: Deviations for constructional screw treads ISO Cor 1 P C M ISO general purpose metric screw treads Tolerances -- Part 3: Deviations for constructional screw treads - Corrigendum 1 ISO P M ISO general purpose metric screw treads -- Tolerances -- Part 4: Limits of sizes for ot-dip galvanized external screw treads to mate wit internal screw treads tapped wit tolerance position H or after galvanizing ISO P M ISO general purpose metric screw treads -- Tolerances -- Part 5: Limits of sizes for internal screw treads to mate wit ot-dip galvanized external screw treads wit maximum size of tolerance position before galvanizing ISO/R 1101/I T M Tolerances of form and of position - Part 1: eneralities, symbols, indications on drawings (Witdrawn ) ISO/R 1101/II T Tecnical drawings - Tolerances of form and of position - Part II: Maximum material principle (witdrawn ) - replaced by ISO 2692:1988 ISO 1101 Extract T Tecnical drawings - eometrical tolerancing - Toleranced caracteristics and symbols - Examples of indication and interpretation (Witdrawn ) ISO 1101 T Tecnical drawings - eometrical tolerancing - Tolerancing of form, orientation, location and run-out - eneralities, definitions, symbols, indications on drawings (witdrawn ) ISO 1101 T eometrical Product Specification (PS) - eometrical tolerancing - Tolerances of form, orientation, location and run-out (Witdrawn ) ISO 1101 P eometrical Product Specifications (PS) -- eometrical tolerancing -- Tolerances of form, orientation, location and run-out (cancels and replaces: ISO 1101:2004 and ISO 10578:1992)

9 List of PS relevant ISO-standards Page 8 of 21 ISO 1101 Cor 1 P eometrical Product Specifications (PS) -- eometrical tolerancing -- Tolerances of form, orientation, location and run-out - Corrigendum 1 - NEW ISO 1101 Amd 1 DIS eometrical product specifications (PS) -- eometrical tolerancing -- Tolerances of form, orientation, location and run-out - Amendment 1 ISO 1101 A2 WD eometrical Product Specifications (PS) - eometrical tolerancing - Tolerancing of form, orientation, location and runout - Amendment 2: Indication of default specifications and special operators ISO 1101 A3 WD eometrical Product Specifications (PS) - eometrical tolerancing - Tolerancing of form, orientation, location and runout - Amendment 3: ISO 1119 T Series of conical tapers and taper angles (witdrawn ) ISO 1119 T eometrical Product Specifications (PS) - Series of conical tapers and taper angles (witdrawn ) ISO 1119 P eometrical Product Specifications (PS) - Series of conical tapers and taper angles ISO 1302 T ? Tecnical drawings - Metod of indicating surface texture on drawings (witdrawn ) ISO 1302 T Tecnical drawings - Metod of indicating surface texture (witdrawn ?) ISO 1302 T Tecnical drawings - Metod of indicating surface texture (witdrawn ?) ISO 1302 P eometrical Product Specifications (PS) - Indication of surface texture in tecnical product documentation ISO 1302 A1 WD eometrical Product Specifications (PS) - Indication of surface texture in tecnical product documentation ISO 1302 A2 DIS eometrical Product Specifications (PS) - Indication of surface texture in tecnical product documentation - Amendment 2 Indication of material ratio requirements ISO/R 1501 T M ISO miniature screw treads (witdrawn ) ISO 1501 P M ISO miniature screw treads ISO/R 1502 T ? M ISO general purpose metric screw treads -- auging ISO 1502 T ? M ISO general purpose metric screw treads -- auging ISO 1502 P M ISO general-purpose metric screw treads auges and gauging ISO/R 1660 T Tecnical drawings - Tolerances of form and of position - Part III: Dimensioning and tolerancing of profiles (witdrawn ) ISO 1660 T ? Tecnical drawings -- Dimensioning and tolerancing of profiles ISO 1660 P Tecnical drawings - Dimensioning and tolerancing of profiles ISO 1660 DIS eometrical product specifications (PS) -- eometrical tolerancing -- Profile tolerancing ISO/R 1661 T Tecnical drawings - Tolerances of form and position - Part IV: Practical examples of indications on drawings (witdrawn ) ISO 1829 T Selection of tolerance zones for general purposes (witdrawn ) - Replaced by ISO 286-1:2010 ISO 1878 T Classification of instruments and devices for measurement and evaluation of te geometrical parameters of surface finis (witdrawn )

10 List of PS relevant ISO-standards Page 9 of 21 ISO 1879 T Instruments for te measurement of surface rougness by te profile metod - Vocabulary (witdrawn ) ISO 1880 T Instruments for te measurement of surface rougness by te profile metod - Contact (stylus) instruments of progressive profile transformation - Profile recording instruments (witdrawn ) - replaced by ISO 3274:1996 ISO/R 1938 P ISO system of limits and fits - Part II: Inspection of plain workpieces ISO FDIS eometrical product specifications (PS) - Dimensional measurement equipment Part 1: Plain limit gauges of linear size ISO 1947 T System of cone tolerances for conical workpieces from C = 1:3 to 1:500 and lengts from 6 to 630 mm (witdrawn ) ISO 2538 T Limits and fits Series of angles and slopes on wedges and prisms (witdrawn ) ISO 2538 P eometrical product specifications (PS) - Series of angles and slopes on prisms ISO FDIS eometrical product specifications -- Wedges -- Part 1: Series of angles and slopes ISO FDIS eometrical product specifications -- Wedges -- Part 2: Dimensioning and tolerancing ISO T Rougness comparison specimens - Part 1: Turned, ground, bored, milled, saped, and planed (witdrawn ) ISO T Rougness comparison specimens - Part 1: Turned, ground, bored, milled, saped, and planed (witdrawn ) ISO T ? Rougness comparison specimens - Part 2: Spark-eroded, sot blasted and grit blasted and polised (witdrawn ) ISO T Rougness comparison specimens - Part 2: Spark-eroded, sot blasted and grit blasted and polised (witdrawn ) ISO T Rougness comparison specimens - Part 3: Cast surfaces (witdrawn ) ISO 2692 T Tecnical drawings - eometrical tolerancing - Maximum material principle (cancels and replaces ISO 1101/II:1974) (witdrawn ) ISO 2692 Amd1 T Tecnical drawings - eometrical tolerancing - Maximum material principle - Amendment 1: Least material requirement (witdrawn ) ISO 2692 P eometrical product specifications (PS) - eometrical tolerancing - Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR) ISO 2692 DIS eometrical product specifications (PS) - eometrical tolerancing - Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR) ISO 2768 T P Permissible macining variations in dimensions witout tolerance indication (witdrawn ) ISO P P eneral tolerances - Part 1: Tolerances for linear and angular dimensions witout individual tolerances ISO P P eneral tolerances - Part 2: eometrical tolerances for features witout individual tolerance indications ISO 2901 T ? M ISO metric trapezoidal screw treads -- Basic profile and maximum material profiles

11 List of PS relevant ISO-standards Page 10 of 21 ISO 2901 P M ISO metric trapezoidal screw treads Basic profile and maximum material profiles ISO 2902 P M ISO metric trapezoidal screw treads eneral plan ISO 2903 T ? M ISO metric trapezoidal screw treads -- Tolerances ISO 2903 P M ISO metric trapezoidal screw treads Tolerances ISO 2904 P M ISO metric trapezoidal screw treads Basic dimensions ISO 3040 T Tecnical drawings - Dimensioning and tolerancing - Cones (witdrawn ) ISO 3040 P eometrical product specifications (PS) -- Dimensioning and tolerancing Cones ISO 3040 AMD1 DIS eometrical product specifications (PS) -- Dimensioning and tolerancing Cones - Amendment 1 ISO 3274 T Instruments for te measurement of surface rougness by te profile metod -- Contact (stylus) instruments of consecutive profile transformation -- Contact profile meters, system M (witdrawn ) ISO 3274 P eometrical product specifications (PS) - Surface texture: Profile metod - Nominal caracteristics of contact (stylus) instruments ISO 3274 C1 P C eometrical product specifications (PS) - Surface texture: Profile metod - Nominal caracteristics of contact (stylus) instruments - Tecnical Corrigendum 1:1998 ISO 3508 P M Tread run-outs for fasteners wit tread in accordance wit ISO 261 and ISO 262 ISO 3599 T Vernier callipers reading to 0,1 and 0,05 mm - New edition out for balloting - witdrawn replaced by ISO :2011 and ISO :2011 ISO 3611 T Micrometer callipers for external measurement (witdrawn ) ISO 3611 P eometrical product specifications (PS) -- Dimensional measuring instruments -- Micrometers for external measurements; Design and metrological caracteristics ISO 3650 T auge blocks (witdrawn ) ISO 3650 P eometrical Product Specifications (PS) -- Lengt standards -- auge blocks ISO 3650 C1 P eometrical Product Specifications (PS) -- Lengt standards -- auge blocks TECHNICAL CORRIENDUM 1 ISO 3670 T Blanks for plug gauges and andles (taper lock and tri-lock) and ring gauges - Design and general dimensions (witdrawn ) ISO 4156 T M Straigt cylindrical involute splines - Metric module, side fit - eneralities, dimensions and inspection - witdrawn ISO P M Straigt cylindrical involute splines -- Metric module, side fit -- Part 1: eneralities ISO P M Straigt cylindrical involute splines -- Metric module, side fit -- Part 2: Dimensions ISO P M Straigt cylindrical involute splines -- Metric module, side fit -- Part 3: Inspection

12 List of PS relevant ISO-standards Page 11 of 21 ISO T Surface rougness -- Terminology -- Part 1: Surface and its parameters (witdrawn ) ISO T Surface rougness -- Terminology -- Part 2: Measurement of surface rougness parameters (witdrawn ) ISO 4287 P eometrical product specifications (PS) - Surface texture: Profile metod - Terms, definitions and surface texture parameters ISO 4287 C1 P C eometrical product specifications (PS) - Surface texture: Profile metod - Terms, definitions and surface texture parameters - Tecnical corrigendum 1: 1998 ISO 4287 C2 P C eometrical product specifications (PS) - Surface texture: Profile metod - Terms, definitions and surface texture parameters - Tecnical corrigendum 2: 2005 ISO 4287 A1 P eometrical Product Specifications (PS) - Surface texture: Profile metod - Terms, definitions and surface texture parameters - AMENDMENT 1: Peak count parameter ISO 4287 Amd 2 DIS eometrical Product Specifications (PS) -- Surface texture: Profile metod -- Terms, definitions and surface texture parameters ISO 4288 T Rules and procedures for te measurement of surface rougness using stylus instruments (witdrawn ) ISO 4288 P eometrical product specifications (PS) - Surface texture: Profile metod - Rules and procedures for te assessment of surface texture ISO 4288 C1 P C eometrical product specifications (PS) - Surface texture: Profile metod - Rules and procedures for te assessment of surface texture - Tecnical Corrigendum 1:1998 ISO 4291 P Metods for te assessment of deviation from roundness - Measurement of variation in radius ISO 4292 P Metods for te assessment of deviation from roundness - Measurement by two and tree-point metods ISO T ? U Tolerances for fasteners -- Part 1: Bolts, screws and nuts wit tread diameters between 1,6 (inclusive) and 150 mm (inclusive) and product grades A, B and C ISO P U Tolerances for fasteners -- Part 1: Bolts, screws, studs and nuts -- Product grades A, B and C ISO/DIS 4910 T Vocabulary for terms used for cones - Newer publised!!!! ISO 5166 T System of cone fits for cones from C = 1 : 3 to 1 : 500, lengts from 6 to 630 mm and diameters up to 500 mm (witdrawn ) ISO 5408 T M Cylindrical screw treads -- Vocabulary - witdrawn ISO 5408 P M Screw treads -- Vocabulary ISO 5436 T Calibration specimens - Stylus instruments - s, calibration and use of specimens (witdrawn ) ISO P eometrical product specifications (PS) - Surface texture: Profile metod; Measurement standards - Part 1: Material measures ISO T eometrical product specifications (PS) - Surface texture: Profile metod; Measurement standards - Part 2: Software measurement standards ISO C1 T C eometrical product specifications (PS) - Surface texture: Profile metod; Measurement standards - Part 2: Software measurement standards -- Tecnical Corrigendum 1:2006

13 List of PS relevant ISO-standards Page 12 of 21 ISO C2 T C eometrical product specifications (PS) - Surface texture: Profile metod; Measurement standards - Part 2: Software measurement standards -- Tecnical Corrigendum 2:2008 ISO P eometrical product specifications (PS) - Surface texture: Profile metod; Measurement standards - Part 2: Software measurement standards ISO 5458 T Tecnical drawings - eometrical tolerancing - Positional tolerancing (witdrawn ?) ISO 5458 P eometrical Product Specifications (PS) - eometrical tolerancing - Positional tolerancing ISO 5459 T Tecnical drawings - eometrical tolerancing - Datums and datum systems for geometrical tolerancing - Witdrawn ISO 5459 P eometrical Product Specifications (PS) - eometrical tolerancing - Datums and datum-systems ISO/TR 5460 P Tecnical drawings - eometrical tolerancing - Tolerancing of form, orientation, location and run-out - Verification principles and metods - uidelines ISO 5864 T ? M ISO inc screw treads -- Allowances and tolerances ISO 5864 P M ISO inc screw treads -- Allowances and tolerances ISO 6318 T Measurement of roundness - Terms definitions and parameters of roundness (witdrawn ) ISO 6410 T ? M Tecnical drawings -- Conventional representation of treaded parts ISO P M Tecnical drawings -- Screw treads and treaded parts -- Part 1: eneral conventions ISO P M Tecnical drawings -- Screw treads and treaded parts -- Part 2: Screw tread inserts ISO P M Tecnical drawings -- Screw treads and treaded parts -- Part 3: Simplified representation ISO 6411 P M Tecnical drawings -- Simplified representation of centre oles ISO 6413 P M Tecnical drawings -- Representation of splines and serrations ISO 6906 T Vernier callipers reading 0,02 mm - New edition out for balloting - witdrawn replaced by ISO :2011 and ISO :2011 ISO 7083 P Tecnical drawings - Symbols for geometrical tolerancing - Proportions and dimensions ISO T ? M Tool sanks wit 7/24 taper for automatic tool cangers -- Part 1: Sanks Nos. 40, 45 and Dimensions - Witdrawn ISO P M Tool sanks wit 7/24 taper for automatic tool cangers -- Part 1: Dimensions and designation of sanks of forms A, AD, AF, U, UD and UF ISO T ? M Tool sanks wit 7/24 taper for automatic tool cangers -- Part 2: Retention knobs for sanks Nos. 40, 45 and Dimensions and mecanical caracteristics ISO P M Tool sanks wit 7/24 taper for automatic tool cangers -- Part 2: Dimensions and designation of sanks of forms J, JD and JF ISO P M Tool sanks wit 7/24 taper for automatic tool cangers Part 3: Retention knobs for sanks of forms AC, AD, AF, UC, UD, UF, JD and JF ISO 7863 P Heigt setting micrometers and riser blocks

14 List of PS relevant ISO-standards Page 13 of 21 ISO 8015 T F Tecnical drawings - Fundamental tolerancing principle - witdrawn ISO 8015 P F eometrical product specifications (PS) -- Fundamentals -- Concepts, principles and rules ISO 8062 T P Castings - System of dimensional tolerances (witdrawn ) ISO 8062 T P Castings - System of dimensional tolerances and macining allowances witdrawn: 2007-?-? ISO P P eometrical Product Specifications (PS) - Dimensional and geometrical tolerances for moulded parts - Part 1: Vocabulary ISO/TS P P eometrical product specifications (PS) - Dimensional and geometrical tolerances for moulded parts - Part 2: Rules ISO P P eometrical product specifications (PS) - Dimensional and geometrical tolerances for moulded parts - Part 3: eneral dimensional and geometrical tolerances and macining allowances for castings ISO C1 P C P eometrical product specifications (PS) - Dimensional and geometrical tolerances for moulded parts - Part 3: eneral dimensional and geometrical tolerances and macining allowances for castings - Tecnical Corrigendum 1 ISO WD P eometrical Product Specifications (PS) -- Dimensional and geometrical tolerances for moulded parts -- Part 4: eneral tolerances for castings (according to te PS rules) ISO P Surface plates - Part 1: Cast iron ISO P Surface plates - Part 2: ranite ISO 8785 P eometrical product specifications (PS) - Surface imperfections - Terms, definitions and parameters ISO 9013 T P Welding and allied processes Quality classification and dimensional tolerances of termally cut (oxygen/fl gas flame) surfaces (witdrawn 2002) ISO 9013 P P Termal cutting Classification of termal cuts eometrical product specification and quality ISO 9013 A1 P A P Termal cutting Classification of termal cuts eometrical product specification and quality - Amendment 1 - ONLY te CEN-standard - NOT te ISO-standard ISO 9121 DIS eometrical product specifications (PS) - Dimensional measuring instruments: Internal micrometer wit two point contact) - Design and metrological requirements ISO 9493 P eometrical product specifications (PS) - Dimensional measuring instruments: Dial test indicator (lever type) - Design and metrological requirements ISO T P Tecnical drawings - Simplified representation of moulded, cast and forged parts (witdrawn ) ISO P P eometrical product specifications (PS) -- Drawing indications for moulded parts in tecnical product documentation (TPD) ISO P eometrical product specifications (PS) - Acceptance and reverification tests for coordinate measuring macines (CMM) - Part 1: Vocabulary ISO C1 P C eometrical product specifications (PS) - Acceptance and reverification tests for coordinate measuring macines (CMM) - Part 1: Vocabulary - Tecnical Corrigendum 1: 2002 ISO T Coordinate metrology - Part 2: Performance assessment of coordinate measuring macines (witdrawn )

15 List of PS relevant ISO-standards Page 14 of 21 ISO T eometrical product specifications (PS) - Acceptance and reverification tests for coordinate measuring macines (CMM) - Part 2: CMMs used for measuring size (witdrawn ) ISO P eometrical Product Specifications (PS) -- Acceptance and reverification tests for coordinate measuring macines (CMM) -- Part 2: CMMs used for measuring linear dimensions ISO P eometrical product specifications (PS) - Acceptance and reverification tests for coordinate measuring macines (CMM) - Part 3: CMMs wit te axis of a rotary table as te fourt axis ISO P eometrical product specifications (PS) - Acceptance and reverification tests for coordinate measuring macines (CMM) - Part 4: CMMs used in scanning measuring mode ISO C1 P C eometrical product specifications (PS) - Acceptance and reverification tests for coordinate measuring macines (CMM) - Part 4: CMMs used in scanning measuring mode - Tecnical Corrigendum 1:2002 ISO T eometrical product specifications (PS) - Acceptance and reverification tests for coordinate measuring macines (CMM) - Part 5: CMMs using multiplestylus probing systems (witdrawn ) ISO P eometrical Product Specifications (PS) -- Acceptance and reverification tests for coordinate measuring macines (CMM) -- Part 5: CMMs using single and multiple stylus contacting probing systems ISO P eometrical product specifications (PS) - Acceptance and reverification tests for coordinate measuring macines (CMM) - Part 6: Estimation of errors in computing aussian associated features ISO C1 P C eometrical product specifications (PS) - Acceptance and reverification tests for coordinate measuring macines (CMM) - Part 6: Estimation of errors in computing aussian associated features - Tecnical Corrigendum 1:2007 ISO P eometrical Product Specifications (PS) -- Acceptance and reverification tests for coordinate measuring macines (CMM) -- Part 7: CMMs equipped wit imaging probing systems ISO FDIS eometrical Product Specifications (PS) -- Acceptance and reverification tests for coordinate measuring macines (CMM) -- Part 8: CMMs wit optical distance sensors ISO FDIS eometrical product specifications (PS) -- Acceptance and reverification tests for coordinate measuring macines (CMM) -- Part 9: CMMs wit multiple probing systems ISO DIS eometrical product specifications (PS) -- Acceptance and reverification tests for coordinate measuring macines (CMM) -- Part 10: Laser trackers for measuring point-to-point distances ISO WD eometrical product specifications (PS) -- Acceptance and reverification tests for coordinate measuring macines (CMM) -- Part 11: Computed Tomograpy ISO T Tecnical drawings - Tolerancing of orientation and location - Projected tolerance zone (Witdrawn Te content is now in ISO 1101:2012) ISO T B Tecnical drawings - Dimensioning and tolerancing - Non-rigid parts (witdrawn ) ISO P B eometrical product specifications (PS) -- Dimensioning and tolerancing Non-rigid parts ISO Cor 1 P B eometrical product specifications (PS) -- Dimensioning and tolerancing Non-rigid parts - Corrigendum 1 - only relevant for te Frenc language version

16 List of PS relevant ISO-standards Page 15 of 21 ISO T eometrical product specifications (PS) - Surface texture: Profile metod - Metrological caracteristics of pase corrected filters - Witdeawn revised by ISO :2011 ISO C1 T C eometrical product specifications (PS) - Surface texture: Profile metod - Metrological caracteristics of pase corrected filters - Tecnical Corrigendum 1: Witdeawn revised by ISO :2011 ISO P eometrical product specifications (PS) - Surface texture: Profile metod - Motif parameters ISO C1 P C eometrical product specifications (PS) - Surface texture: Profile metod - Motif parameters - Tecnical Corrigendum 1:1998 ISO P eometrical product specifications (PS) - Surface texture: Profile metod - Calibration of contact (stylus) instruments ISO C1 P C eometrical product specifications (PS) - Surface texture: Profile metod - Calibration of contact (stylus) instruments - Tecnical Corrigendum 1:2003 ISO/TS T eometrical product specifications (PS) - Cylindricity - Part 1: Vocabulary and parameters of cylindrical form - witdrawn Marc 2011 ISO P eometrical product specifications (PS) - Cylindricity - Part 1: Vocabulary and parameters of cylindrical form ISO/TS T eometrical product specifications (PS) - Cylindricity - Part 2: Specification operators - witdrawn Marc 2011 ISO/TS C1 T C eometrical product specifications (PS) - Cylindricity - Part 2: Specification operators - Tecnical Corrigendum 1 - witdrawn Marc 2011 ISO P eometrical product specifications (PS) - Cylindricity - Part 2: Specification operators ISO/TS T eometrical product specifications (PS) - Roundness Part 1: Vocabulary and parameters of roundness - witdrawn Marc 2011 ISO P eometrical product specifications (PS) - Roundness Part 1: Vocabulary and parameters of roundness ISO/TS T eometrical product specifications (PS) - Roundness Part 2: Specification operators - witdrawn Marc 2011 ISO/TS C1 T C eometrical product specifications (PS) - Roundness Part 2: Specification operators - Tecnical Corrigendum 1 - witdrawn Marc 2011 ISO P eometrical product specifications (PS) - Roundness Part 2: Specification operators ISO/TS T eometrical product specifications (PS) - Straigtness Part 1: Vocabulary and parameters of straigtness - witdrawn Marc 2011 ISO P eometrical product specifications (PS) - Straigtness Part 1: Vocabulary and parameters of straigtness ISO/TS T eometrical product specifications (PS) - Straigtness Part 2: Specification operators - witdrawn Marc 2011 ISO/TS C1 T C eometrical product specifications (PS) - Straigtness Part 2: Specification operators - Tecnical Corrigendum 1 - witdrawn Marc 2011 ISO P eometrical product specifications (PS) - Straigtness Part 2: Specification operators ISO/TS T eometrical product specifications (PS) - Flatness Part 1: Vocabulary and parameters of flatness - witdrawn Marc 2011

17 List of PS relevant ISO-standards Page 16 of 21 ISO P eometrical product specifications (PS) - Flatness Part 1: Vocabulary and parameters of flatness ISO/TS T eometrical Product Specifications (PS) - Flatness Part 2: Specification operators - witdrawn Marc 2011 ISO/TS C1 T C eometrical Product Specifications (PS) - Flatness Part 2: Specification operators - Tecnical Corrigendum 1 - witdrawn Marc 2011 ISO P eometrical Product Specifications (PS) - Flatness Part 2: Specification operators ISO/PAS T eometrical product specification (PS) -- Coordinate measuring macines (CMM): Testing te performance of CMMs using single-stylus contacting probing systems - witdrawn ISO P eometrical product specifications (PS) -- Dimensional measuring equipment: Electronic digital indicator gauge Design and metrological caracteristics ISO P eometrical product specifications (PS) -- Dimensional measuring instruments; Heigt gauges Design and metrological caracteristics ISO P eometrical product specifications (PS) - Dimensional measuring instruments: Part 1 - Callipers - Design and metrological requirements (cancels and replaces: ISO 3599:1976 and ISO 6906:1984) ISO P eometrical product specifications (PS) - Dimensional measuring instruments: Part 2 - Calliper dept gauges - Design and metrological requirements (cancels and replaces: ISO 3599:1976 and ISO 6906:1984) ISO P T Tecnical product documentation (TPD) -- Dimensioning and indication of knurling ISO P eometrical product specifications (PS) - Surface texture: Profile metod - Surfaces awing stratified functional properties - Part 1: Filtering and measurement conditions ISO C1 P C eometrical product specifications (PS) - Surface texture: Profile metod - Surfaces awing stratified functional properties - Part 1: Filtering and measurement conditions - Tecnical Corrigendum 1:1998 ISO P eometrical product specifications (PS) - Surface texture: Profile metod - Surfaces awing stratified functional properties - Part 2: Heigt caracterisation using te linear material ratio curve ISO C1 P C eometrical product specifications (PS) - Surface texture: Profile metod - Surfaces awing stratified functional properties - Part 2: Heigt caracterisation using te linear material ratio curve - Tecnical Corrigendum 1:1998 ISO P eometrical product specifications (PS) - Surface texture: Profile metod - Surfaces awing stratified functional properties - Part 3: Heigt caracterisation using te material probability curve ISO T Tecnical drawings - Corners - Vocabulary and indication on drawings (witdrawn ??) ISO P Tecnical drawings - Edges of undefined sape - Vocabulary and indications ISO P P Welding eneral tolerances for welded constructions Dimensions for lengts and angles -- Sape and position ISO T B eometrical Product Specification (PS) - Inspection by measurement of workpieces and measuring equipment - Part 1: Decision rules for proving conformance or nonconformance wit specifications - Witdrawn July 2013

18 List of PS relevant ISO-standards Page 17 of 21 ISO P B eometrical Product Specification (PS) - Inspection by measurement of workpieces and measuring equipment - Part 1: Decision rules for proving conformance or nonconformance wit specifications requirements (cancels and replaces: ISO/TS :1998) ISO/TS T B eometrical Product Specification (PS) - Inspection by measurement of workpieces and measuring equipment - Part 2: uide to te estimation of uncertainty in PS measurement, in calibration of measuring equipment and in product verification - witdrawn April 2011 ISO/TS C1 T C B eometrical Product Specification (PS) - Inspection by measurement of workpieces and measuring equipment - Part 2: uide to te estimation of uncertainty in PS measurement, in calibration of measuring equipment and in product verification - Tecnical Corrigendum 1: witdrawn April 2011 ISO P B eometrical product specifications (PS) -- Inspection by measurement of workpieces and measuring equipment -- Part 2: uidance for te estimation of uncertainty in PS measurement, in calibration of measuring equipment and in product verification ISO Cor1 P B eometrical product specifications (PS) -- Inspection by measurement of workpieces and measuring equipment -- Part 2: uidance for te estimation of uncertainty in PS measurement, in calibration of measuring equipment and in product verification - Corrigendum 1:2013 ISO/TS T B eometrical Product Specification (PS) - Inspection by measurement of workpieces and measuring equipment - Part 3: uidelines for acieving agreements on measurement uncertainty statements - witdrawn April 2011 ISO P B eometrical Product Specification (PS) - Inspection by measurement of workpieces and measuring equipment - Part 3: uidelines for acieving agreements on measurement uncertainty statements ISO/TS P B eometrical Product Specification (PS) - Inspection by measurement of workpieces and measuring equipment - Part 4: Background on functional limits and specification limits in decision rules ISO DIS B eometrical Product Specifications (PS) -- Inspection by measurement of workpieces and measuring equipment -- Part 5: Uncertainty in testing indicating measuring instruments ISO/TR P B eometrical product specifications (PS) -- Inspection by measurement of workpieces and measuring equipment -- Part 6: eneralized decision rules for te acceptance and rejection of instruments and workpieces ISO P eometrical Product Specification (PS) - Dimensional Tolerancing - Linear Sizes ISO A1 DIS eometrical Product Specification (PS) - Dimensional Tolerancing - Linear Sizes - Amendment 1 ISO P eometrical product specifications (PS) -- Dimensional tolerancing -- Part 2: Dimensions oter tan linear sizes ISO CD eometrical product specifications (PS) -- Dimensional tolerancing -- Part 3: Angular sizes ISO P B eometrical Product Specifications (PS) - Extraction ISO/TR P F eometrical Product Specifications (PS) - Master plan ISO/TR DIS F eometrical Product Specifications (PS) - Master plan ISO T F eometrical Product Specifications (PS) - Fundamentals - Concepts, principles and rules - Te content is moved to te next edition of ISO Project canged/stopped June 2011

19 List of PS relevant ISO-standards Page 18 of 21 ISO P B eometrical Product Specifications (PS) - eometrical features - Part 1: eneral terms and definitions ISO P B eometrical Product Specifications (PS) - eometrical features - Part 2: Extracted median line of a cylinder and a cone, extracted median surface, local size of an extracted feature ISO A1 DIS B eometrical Product Specifications (PS) - eometrical features - Part 2: Extracted median line of a cylinder and a cone, extracted median surface, local size of an extracted feature - Amendment 1 ISO P B eometrical Product Specifications (PS) - eneral concepts and requirements for PS measuring equipment ISO C1 P C B eometrical Product Specifications (PS) - eneral concepts and requirements for PS measuring equipment - Tecnical Corrigendum 1:2006 ISO CD B eometrical Product Specifications (PS) - Textual equivalents for dimensional and geometrical tolerancing - Part 1: Dimensional and geometrical tolerancing ISO CD B eometrical Product Specifications (PS) - Textual equivalents for dimensional and geometrical tolerancing - Part 2: Surface texture ISO/TS P eometrical Product Specifications (PS) - Coordinate measuring macines (CMMs): Tecniqs for evaluation of te uncertainty of measurement - Part 1: Overview and metrological caracteristics ISO/TS CD eometrical Product Specifications (PS) - Coordinate measuring macines (CMMs): Tecniqs for evaluation of te uncertainty of measurement - Part 2: Use of multiple measurement strategies ISO/TS T eometrical Product Specifications (PS) - Coordinate measuring macines (CMM): Tecniqs for evaluation of te uncertainty of measurement - Part 3: Use of calibrated workpieces or standards (Witdrawn ) ISO P eometrical Product Specifications (PS) - Coordinate measuring macines (CMM): Tecniqs for determining of te uncertainty of measurement - Part 3: Use of calibrated workpieces or measurement standards ISO/TS P eometrical Product Specifications (PS) - Coordinate measuring macines (CMM): Tecniqs for evaluation of te uncertainty of measurement - Part 4: Use of computer simulation ISO/TS WD eometrical Product Specifications (PS) - Coordinate measuring macines (CMM): Tecniqs for evaluation of te uncertainty of measurement - Part 5: Use of statistical estimation ISO/TS WD eometrical Product Specifications (PS) - Coordinate measuring macines (CMM): Tecniqs for evaluation of te uncertainty of measurement - Part 6: Use of un-calibrated workpieces ISO P ? T Tecnical drawings -- Symbolic presentation and indication of adesive, fold and pressed joints ISO P T Tecnical drawings -- Simplified representation and dimensioning of oles ISO P T Tecnical Product Documentation (TPD) -- Heat-treated ferrous parts -- Presentation and indications ISO DIS T Tecnical product documentation -- Heat-treated ferrous parts -- Presentation and indications ISO/TR P B eometrical Product Specifications (PS) - Systematic errors and contributions to measurement uncertainty of linear dimensional measurements d to termal inflnces ISO FDIS M Metric series wires for measuring screw

20 List of PS relevant ISO-standards Page 19 of 21 ISO/TR T eometrical product specification (PS) - Linear and angular dimensioning and tolerancing: ± limit specifications - Step dimensions, distances, angular sizes and radii (witdrawn ) - NOT replaced ISO/TS P B eometrical Product Specifications (PS) - Filtration - Part 1: Overview and basic concepts ISO DIS B eometrical Product Specifications (PS) - Filtration - Part 1: Overview and basic concepts ISO/TS P B eometrical Product Specifications (PS) - Filtration - Part 20: Linear profile filters: Basic concepts ISO DIS B eometrical Product Specifications (PS) - Filtration - Part 20: Linear profile filters: Basic concepts ISO P B eometrical product specifications (PS) -- Filtration Part 21: Linear profile filters: aussian filters (cancels and revises ISO 11562:1996 and ISO Cor 1:1998) ISO/TS P B eometrical product specifications (PS) - Filtration - Part 22: : Linear profile filters: Spline filters ISO DIS B eometrical product specifications (PS) - Filtration - Part 22: : Linear profile filters: Spline filters ISO/TS P B eometrical product specifications (PS) -- Filtration Part 28: Profile filters: End effects ISO/TS P B eometrical product specifications (PS) - Filtration - Part 29: Linear profile filters: Spline Wavelets ISO DIS B eometrical product specifications (PS) - Filtration - Part 29: Linear profile filters: Spline Wavelets ISO/TS P B eometrical product specifications (PS) -- Filtration Part 30: Robust profile filters: Basic concepts ISO DIS B eometrical product specifications (PS) -- Filtration -- Part 30: Robust profile filters: Basic concepts ISO/TS P B eometrical Product Specifications (PS) - Filtration - Part 31: Robust profile filters: aussian regression filters ISO/TS P B eometrical product specifications (PS) - Filtration - Part 32: Robust profile filters: Spline filters ISO DIS B eometrical product specifications (PS) -- Filtration -- Part 32: Robust profile filters: Spline filters ISO/TS P B eometrical product specifications (PS) - Filtration - Part 40: Morpological profile filters: Basic concepts ISO DIS B eometrical product specifications (PS) - Filtration - Part 40: Morpological profile filters: Basic concepts ISO/TS P B eometrical Product Specifications (PS) - Filtration - Part 41: Morpological profile filters: Disk and orizontal segment filters ISO DIS B eometrical Product Specifications (PS) - Filtration - Part 41: Morpological profile filters: Disk and orizontal segment filters ISO/TS P B eometrical Product Specifications (PS) - Filtration - Part 49: Morpological profile filters: Scale space tecniqs ISO DIS B eometrical Product Specifications (PS) - Filtration - Part 49: Morpological profile filters: Scale space tecniqs