HDD/DVD VIDEO RECORDER RD-XS55KU. Quick Reference

Transcription

1 /DVD VIDEO RECORDER RD-XS55KU Quick Reference This booklet is to help you start up your recorder and experience a basic operation. To learn about the recorder and obtain its full performance, refer to the Owner s Manual. ( I xx is reference page in the INSTALLATION GUIDE, and O xx in the OPERATIONS GUIDE.) IMPORTANT: Before starting your hook-up and installation of your DVD recorder, please review the safety instructions on I - I 9 in the INSTALLATION GUIDE. Notes on This unit contains a hard disc drive (). A is subject to shock, shakes, and environmental changes such as temperature, which can damage data stored on the disc. Observe the following instructions. Do not shock or shake the unit (especially during operation). Do not use the unit on a shaky or unstable surface. Do not place the unit on a location where it is not horizontal. Do not cover the ventilation holes for the cooling fan. Do not use in a location where the temperature rises or changes rapidly. Do not disconnect the power plug from a wall outlet while the unit is turned on. Do not disconnect the power plug from a wall outlet or break power supply to the unit. Before disconnecting the power plug, be sure to press the power button and make sure the unit ends the finishing process and the power turns off completely. If the power plug is disconnected or power supply is disrupted while the unit is recording, all recorded content will be erased. Toshiba is not liable for any damage or loss of recorded data caused by shock, shakes, misoperation or malfunction. P H PM

2 Make sure the following accessories are supplied. Supplied accessories Remote control... Batteries (AAA)... Coaxial cable... Video/audio cable... G-LINK cable... LAN cable... Power cord... OWNER S MANUAL (INSTALLATION GUIDE)... OWNER S MANUAL (OPERATIONS GUIDE)... Preparing the remote control Open the cover. Insert Close batteries (AAA size). Make sure to match the + and on the batteries to the marks inside the battery compartment. the cover. Point the remote control at the remote sensor and press the buttons. Connections Connect Connect Connect 4 Connect 5 If 6 Connect your cable box to the RF IN (FROM ANT.) terminal or the INPUT jacks on the recorder. If you use the DSS set top box control function I 4, connect your satellite set top box to the INPUT jacks. If you are not using a cable box, disconnect the antenna cable from your TV, and connect it to the RF IN (FROM ANT.) terminal on the recorder. Then skip to step.) the supplied G-LINK cable to the G-LINK jack on the recorder. Place the transmitter as close as possible to the signal sensor of the cable box. the supplied coaxial cable of this recorder to the RF OUT (TO TV) terminal on the recorder and your TV. the supplied video/audio cable to the OUTPUT jacks on the recorder and your TV. you record from a VCR, connect it to the recorder. The following inputs are available: Rear: INPUT jacks, INPUT jacks Front: INPUT jacks (Open the lid on the left corner of the front panel.) the power cord of the recorder to a wall outlet. Make sure that the powered recorder lights the ON/STANDBY indicator on the front panel. 0 0 Within about 7 m ( ft) Distance: Angle: About 7 m ( ft) from the front of the remote sensor About 0 in each direction of the front of the remote sensor

3 Refer to the owner s manual of each connected equipment as well. Select one of these connections. Set top box Cable box Place close to the signal sensor of the set top box. G-LINK cable (supplied) COMPONENT OUTPUT (See I 8.) (Red) (White) (Yellow) Antenna cable (not supplied) HDMI OUTPUT (See I 6.) 6 To wall outlet 4 (Red) (White) (Yellow) 5 Coaxial cable (supplied) Power cord (supplied) LAN(0/00) (See O 46.) Video/audio cable (supplied) VCR Antenna splitter (not supplied) Types of an antenna terminal may vary depending on the TV. Check your type on your TV, and connect properly using either method as shown. If the TV has an S-video input, connect the recorder with an S-video cable. When using an S-video cable, do not connect the yellow video cable. To S-video input VHF/UHF To video input To audio input TV The RF OUT (TO TV) terminal (step ) is for tuner pass through only. To view pictures from the recorder, the video cables must be connected.

4 Start Settings Preparation Turn on the equipment (TV, VCR, etc.) connected to the recorder. Select the corresponding video input on your TV. ON/STANDBY on the front panel or on the remote control. When the power turns on, ON/STANDBY indicator changes color from red (standby mode) to green (operation). After a few seconds, a startup screen appears. The following icon will appear on the top right corner of the screen. Loading When the icon disappears, the recorder is ready to operate. Note To turn the recorder off, press ON/STANDBY again. When the recorder is turned on for the first time, the Welcome screen will be displayed after the Loading icon has disappeared. ENTER to start your setup. The next screen appears. Make the TV Guide On Screen setup (next page). In the United States, TV Guide and other related marks are registered marks of Gemstar-TV Guide International, Inc. and/or one of its affiliates. In Canada, TV Guide is a registered mark of Transcontinental Inc., and is used under license by Gemstar-TV Guide International, Inc. Aux Etats Unis TV Guide et d autres marques relatives sont des marques déposées de Gemstar-TV Guide International, Inc. et/ou d une de ses sociétés affiliées. Au Canada TV Guide est une marque déposée de Transcontinental Inc., utilisée sous licence de Gemstar-TV Guide International. Inc. The TV Guide On Screen system is manufactured under license from Gemstar-TV Guide International, Inc. and/or one of its affiliates. Le système TV Guide On Screen est fabriqués sous licence de Gemstar- TV Guide International, Inc. et/ou d une de ses sociétés affiliées. Start ON/STANDBY indicator The TV Guide On Screen system is protected by one or more of the following issued United States patents 6,498,895, 6,48,556, 6,,877, 6,9,794; 6,54,0; 5,940,07; 4,908,7; 4,75,578; 4,706,. Le système TV Guide On Screen est protégés par un ou plusieurs brevets émis aux Etats Unis, comme le 6,498,895, 6,48,556, 6,,877, 6,9,794; 6,54,0; 5,940,07; 4,908,7; 4,75,578; 4,706,. Please note that over-the-air or cable access to stations carrying TV Guide On Screen data is required for the TV Guide On Screen system to operate. TV Guide On Screen does not work with satellite programming. Toshiba does not provide the TV Guide On Screen data. Instead, the data is provided by a third party, which is responsible for the accuracy and availability of the data. Additionally, occasional compatibility issues may exist between the TV Guide On Screen system contained in your /DVD Video Recorder and the data provided by the third party. In the event that you experience any performance issues with your TV Guide On Screen system, please do not hesitate to contact the Toshiba America Consumer Products, L.L.C. Consumer Solutions Department by calling (800) 6-8 or by visiting 4

5 TV Guide On Screen Setup Setup selection Reminder Your DVD Recorder is equipped with the TV Guide On Screen Interactive Program Guide, which provides program listings, one-touch recording, and more all subscription FREE! Please follow the on-screen setup instructions to enable your TV Guide On Screen system now. Or, press the GUIDE Key on your DVD Recorder remote at any time. 4 Cable service STEP : Configuring for Cable To supply your DVD Recorder with correct program listings, the TV Guide On Screen system needs to know if your DVD Recorder receives its signal from a cable service. Do you have cable service connected to this DVD recorder? No What would you like to do now? Set up TV Guide On Screen now Remind me to set it up later Don t remind me again Using your DVD Recorder remote, move up or down to highlight your answer. Instructions are provided at the bottom for each screen. / to select Set up TV Guide On Screen Now, then press ENTER. Country STEP : Identifying Your Location To supply your DVD Recorder with correct program listings, the TV Guide On Screen system needs to know your DVD Recorder s location. 5 Cable Using your DVD Recorder remote, move up or down to highlight your answer. / to select, then press ENTER. If the answer is No, you will go to step. connection STEP : Configuring for Cable You have indicated that you have cable service. Now the TV Guide On Screen system needs some additional information. Is a cable box connected to this DVD Recorder? No Which country is your DVD Recorder located in? USA Canada Using your DVD Recorder remote, move up or down to highlight your answer. / to select, then press ENTER. Zip Using your DVD Recorder remote, move up or down to highlight your answer. / to select, then press ENTER. or postal code STEP : Identifying Your Location To supply your DVD Recorder with the correct program listings, the TV Guide On Screen system needs to know the town or city where your DVD Recorder is installed. 6 Cable If you select, the DSS set top box control function is disabled. To use this function, select No and make the setting of I 4. input STEP : Configuring for Cable Your DVD Recorder has more than one input jack. To operate properly with your cable box, the TV Guide On Screen system needs to know which one your cable box is plugged into. You may have to look at the back of your DVD Recorder if you are unsure, as an incorrect selection will result in a blue or snowy screen while watching TV. Please enter the 5-digit ZIP code where your DVD Recorder is located: = = = = = Please indicate which DVD Recorder input the cable box is plugged into. TUNER Line Using your DVD Recorder remote, move up, down, left, or right to enter your information. Enter to confirm. Input your numbers by either below, then press ENTER: Number buttons / to select a number, then / to move to another field 5 Using your DVD Recorder remote, move up or down to highlight your answer. / to select, then press ENTER. If you select TUNER, you will go to step 7. If you select Line, you will go to step 8. (Continued)

6 Settings (Continued) 7 Tuning channel for the cable box STEP : Configuring for Cable To operate properly with your cable box, the TV Guide On Screen system needs to know the channel your DVD Recorder is on when using the cable box. The most commonly used output channel is 0. Please consult your cable box provider if you are unsure, as an incorrect selection will result in a blue or snowy screen while watching TV. What is your DVD Recorder tuned to when using the cable box? Ch Ch Ch 4 Cable box code testing STEP : Configuring for Cable Cable testing in progress... please do not press any keys on any remote control. Now testing code 06 (Toshiba)... Using your DVD Recorder remote, move up or down to highlight your answer. Enter to continue. / to select, then press ENTER. When testing is done, the following screen automatically appears. 8 Read 9 Cable the instruction and the diagram, and confirm the G-LINK cable is properly installed. If OK, press ENTER. box brand name STEP : Configuring for Cable Selecting the correct cable box brand from the list is needed to automatically receive program listings. If you do not know the cable box brand, please consult your cable provider. STEP : Configuring for Cable The TV Guide On Screen system needs to locate the correct code for yourcable box brand in order to work properly. Is your cable box now tuned to channel 09? No Test the code again Using your DVD Recorder remote, move up or down to highlight your answer. What brand of cable box is connected to this DVD Recorder? Not listed Archer Cable Cinema Cabletenna / to select, then press ENTER. If your answer is, and: if you selected TUNER at step 6, you will go to step. if you selected Line at step 6, you will go to step. 0 Using your DVD Recorder remote, move up or down through the list to find your brand (move down for more brands). / to select, then press ENTER. Cable box preparation STEP : Configuring for Cable The TV Guide On Screen will conduct a series of tests to find the correct code to control your cable box. Antenna connection STEP : Configuring for Antenna To supply your DVD Recorder with correct program listings, the TV Guide On Screen system needs to know if you have attached an antenna to your DVD Recorder to receive over-the-air stations. Do you have an antenna connected to your DVD Recorder? No Follow steps A and B below A: Please tune your cable box to channel 0 B: Make sure to leave your cable box turned ON Using your DVD Recorder remote, move up or down to highlight your answer. / to select, then press ENTER. Once you have completed these steps, press Enter on the DVD Recorder remote to begin testing. Follow the instructions, then press ENTER. 6

7 Confirmation STEP 4: Confirming Your Settings You have entered the following TV Guide On Screen system settings. If any setting is marked INCOMPLETE, you will not be able to use the feature until you complete that portion of TV Guide On Screen system setup. ZIP code (USA) Cable Box on input TUNER Ch. Cable Box selected: code 06 (Toshiba) Are the above settings correct?, end setup No, repeat setup process Using your DVD Recorder remote, move up or down to highlight your answer. / to select, then press ENTER. Notes If you move to another area or change your cable box or antenna and cable configulation, redo the TV Guide On Screen setup. TV Guide and select SETUP with /, then press ENTER. If TV Guide On Screen system is not available or has any troubles in your area, try another method to control channels. See C: Satellite set top box setting I 4. The settings are all complete. Proceed to the next page to begin your operation. 4 Confirmation Congratulations! You have completed the setup of your TV Guide On Screen system.up-to-date listings will begin loading over the next 4 hours when your DVD Recorder is powered off. It may take more than one day for all eight days of listings to update. During this period feel free to use your DVD Recorder. The guide will automatically receive updates during the period when your DVD Recorder is turned off. If you have changed the location or cable configuration settings, you will receive any changes to your local channel lineup within 4 hours. Enter to continue. You have successfully completed the setup! ENTER. 5 Information Helpful information. To receive your channel lineup and program listings, leave your cable box ON. Your DVD Recorder should be turned OFF overnight.. To view program listings, press the GUIDE key on your DVD Recorder remote.. You must redo TV Guide On Screen system setup if you: Move your DVD Recorder to a new ZIP or postal code Cancel cable service or change cable boxes To enter the TV Guide On Screen system setup, press the GUIDE key, then go to the Menu Bar and highlight Setup. Enter to continue. Read the information and press ENTER. 7

8 Operations Whenever you operate the recorder: Turn on the equipment (TV, VCR, etc.) connected to the recorder. Select the corresponding video input on your TV. ON/STANDBY to turn the recorder on. Notes on Loading While the icon is flashing: The recorder is checking the status and reading data of the and the DVD drive for startup. (If the DVD drive does not contain a disc, the recorder consumes less time to startup, because it does not need to read data from the DVD drive.) The recorder cannot respond to any operations of buttons other than CH/Page and INPUT SELECT. Operate all other functions after the icon has disappeared. Never unplug the recorder, as the unit and recorded data may be damaged. Loading a disc OPEN/CLOSE to open the disc tray. DVD-RAM disc with cartridge (TYPE/TYPE/TYPE4) Face the side to use (for double sided disc) or the printed side (for single sided disc) up, and insert the cartridge into the tray frame following the direction of the arrow on the cartridge. Disc without cartridge After loading a disc, press OPEN/CLOSE again to close the disc tray. Place a disc in the inside hollow. Disc selection The recorder is compatible with the following discs. DVD-RAM DVD-R DVD-RW Which should be used to record? It depends on the purpose of use. Purpose Recording Recording copy-once programs Editing Playing on a device other than this recorder DVD-RAM (on compatible device) DVD-R No No (on most DVD players) DVD-RW No No (on most DVD players) This is a brief explanation. For more details, see O, O 8. Therefore, DVD-RAM is better for recording, and DVD-R/RW for distribution of recorded contents. DVD-RAM DVD-RAM DVD-R DVD-RW Note on DVD-R/RW recording When recording directly on a DVD-R/RW, or when recording contents which will be copied to a DVD-R/ RW later, make the settings. See O 9. A recorded DVD-R/RW needs to be finalized to play on another DVD player. Notes Some DVD-R/DVD-RW discs may be incompatible due to laser pick-up and disc design. DVD-R/DVD-RW must be recorded using DVD-Video method for video playback. 8

9 Selecting a channel INPUT SELECT to select the input to which the cable box is connected (ch/ch/4ch/line, page 5, 6). CH/Page or the number buttons. If you did not connect a cable box: CH/Page or the number buttons. Recording a current program or DVD to select a media to record on. : To record on the. DVD : To record on a DVD-RAM/R/RW disc. The or DVD indicator illuminates. REC MODE repeatedly to select a recording mode. The recorder stores 5 user recording modes to facilitate the selection of picture and sound quality. Each time you press REC MODE, the indicator on the front panel display changes. SP: Standard setting. (Default at factory set) LP: For longer recording, but inferior to SP in picture quality. MN: Customized setting of bit rate. You can set one recording mode as default. Also you can customize each recording mode. See O 8. REC. Recording starts. To stop recording STOP. Note One recording cannot exceed 9 hours even if the is selected. When a DVD disc is used, the time that can be recorded varies according to the recording mode and the residual capacity of the disc. Checking the disc capacity REMAIN. The disc capacity is displayed at the bottom of the screen. To turn it off, press REMAIN again. 9

10 Operations Recording from a connected VCR INPUT SELECT repeatedly so that L-, L-, or L- appears on the front panel display, corresponding to the input in which the device is connected. Each time you press the button, the indicator changes. L-: To record pictures from equipment connected to the INPUT jacks on the rear panel. L-: To record pictures from equipment connected to the INPUT jacks on the front panel. L-: To record pictures from equipment connected to the INPUT jacks on the rear panel. Perform steps - of Recording a current program (page 9). REC of this recorder to start recording. 4 Start playback of the source content on the connected equipment. 5 When recording is completed, press STOP. Playing recorded contents CONTENT MENU. CONTENT MENU Title List appears. CONTENT MENU Title List / Page 00: 006/0/4 07:00 am TV:4 (0:5:45) 006/0/9 09:00 pm TV: (0:5:40) 006/0/4 :00 pm TV:6 (0:9:50) 006/04/07 07:00 am TV:8 (0:54:0) / / / to select a title (chapter). The following buttons are available., DVD: To switch the drive. PICTURE SEARCH: To turn the page. : To view chapters in the current title. ENTER. 006/04/07 :00 am TV:4 (0:0:08) 006/04/08 09:00 pm TV:0 (0:5:8) Playback starts from a selected title (chapter). To stop playback STOP. 0

11 Erasing content On CONTENT MENU, select an unnecessary title (chapter). QUICK MENU. A Quick Menu appears. CONTENT MENU Title List Page Quick Menu / Title : information Create thumbnail 004/06/08 07:00 High speed dubbing am TV:4 Rate conversion dubbing (0:5:45) Chapter function Edit function 004/06/ 09:00 Special playback pm mode TV: Save captured images (0:5:40) Disc information Display changeover 004/07/ :00 Specific page pm jump TV:4 Title delete (0:0:08) Exit / / / to select Title delete. CONTENT MENU Title List Page Quick Menu / Title : information Create thumbnail 004/06/08 07:00 High speed dubbing am TV:4 Rate conversion dubbing (0:5:45) Chapter function Edit function 004/06/ 09:00 Special playback pm mode TV: Save captured images (0:5:40) Disc information Display changeover 004/07/ :00 Specific page pm jump TV:4 Title delete (0:0:08) Exit 4 ENTER. 5 The confirmation message appears. / to select or No then press ENTER again. Copying recorded contents On CONTENT MENU, select a title (chapter). QUICK MENU. The Quick Menu appears. / / / to select High speed dubbing, then press ENTER. CONTENT MENU High Speed Library Dubbing 006/04/0 09:00pm TV:4 006/0/4 :00 pm TV:6 (0:9:50) 006/04/07 07:00 am TV:8 (0:54:0) 006/04/08 09:00 pm TV:0 (0:5:8) 006/0/4 :00 pm TV:6 (0:9:50) 006/04/07 07:00 am TV:8 (0:54:0) 006/04/08 09:00 pm TV:0 (0:5:8) (0:5:40) Copy (Saves ) Move (Deletes ) Same Disc (Saves ) Network (Saves ) 4 5 / to select Copy, Move, Same Disc or Network. To copy from the to a loaded disc, select Copy. For details, see O 00. ENTER. Copying starts. Playing a DVD-video disc Load a disc. DVD. PLAY. When a top menu appears Some DVD video discs may include a top menu, on which you can view the structure of contents or select a scene. Most of the top menus automatically appear in certain scenes, and also are displayed on demand. Actual operation of the top menu depends on the disc. This section explains a general example of how to operate a top menu. Also refer to the instructions of the disc itself. ) TOP MENU. ) / / / to select the title you want. If the titles in the top menu are assigned a number, you can directly locate a specific title by pressing its designated number with the number buttons. ) ENTER. Changing the playback speed To skip by the specific time. To go back by the specific time. To skip chapters/tracks. To play in slow-motion. To play in fast reverse or fast forward. To play frame by frame. To stop playback. To pause playback.

12 Operations Using the TV Guide On Screen services As you have done TV Guide On Screen setup, you can do the following services of TV Guide. LISTINGS: Check out up to 8 days on on-screen listings RECORDINGS: Keep track of everything you record SEARCH: Sort by keyword, movies, sports, HDTV, and more SCHEDULE: Review and modify scheduled recordings and reminders SETUP: Change defaults to your preference or redo the setup TV Guide. The TV Guide Listings appears. Main service 8:0 RECORDINGS LISTINGS SEARCH Menu now for Listings Options Move to highlight any show Enter to tune to current show in glid Menu for more current show options INFO Select To Video window Info Box the service by pressing /, then press ENTER. See the next page for the services. exit the TV Guide mode, press TV Guide. A program in the video window appears in a full screen. You may use the following buttons: / / / : Moves the highlight. ENTER: Makes a selection or executes an action. Menu: Displays a Panel Menu which you can choose options. Info: (while INFO is displayed) Changes the Info Box size. Opens a Help screen when you move the highlight on the service bar. CH/Page: Turns the page.

13 LISTINGS Whenever you enter the TV Guide mode, you will first see this service. ing Info opens a Help screen. Operate following the guidance. Notes On a Panel Menu, an option may have arrows on both sides. / to cycle the selection. On a Panel Menu, pressing Menu cancels any changes and closes the menu. Selecting a program Selecting a channel Setting a program to remind or record Locking/unlocking the video window, etc. SEARCH You can select programs by category or by keyword. ing Info opens a Help screen. Operate following the guidance. Searching by category (Alphabetical, HDTV, Movies, Sports, Children, Educational,, Variety, Series) Searching by entering a keyword, etc. RECORDINGS You can display a list of previously recorded or currently recording programs on the recorder or the currently loaded DVD-RAM disc. ing Info opens a Help screen. Operate following the guidance. Listing programs in alphabetical order or by date and time Playing recorded program from where was last stopped or the beginning Deleting recorded programs, etc. SCHEDULE You can set, review, edit, or delete recording or remind events. ing Info opens a Help screen. Operate following the guidance. Setting a recording event from the frequency selection (Once, Regularly, Weekly) Setting a reminder from the frequency selection (Once, Regularly, Weekly) Deleting recording or reminder events. Editing a recording event, etc. SETUP You can change defaults. Also you may redo the setup from here. ing Info opens a Help screen. Operate following the guidance. Arranging the position the channel appears in Listings Changing the tuning channel number Switching channels on/off in Listings Changing Info Box size Extending a recording s start or end time Adjusting the time you receive a reminder. Executing the setup again, etc.

14 Operations Program recording with TV Guide On Screen TV Guide. CONTENT MENU Title List / Page :9 Welcome to Using RECORDINGS Menu now for Listings Options Move to highlight any show Enter to tune to current show in glid Menu for more current show options LISTINGS TODAY :00AM :0AM bcd Nightline BOX Rainfield Limpsons GBS Dave Live Jay Lean QBS Charles Rose Fisher Spin Town Everybody loves... Bill & Greg SEARCH INFO / to select LISTINGS. A list of TV programs is displayed on the menu. CONTENT MENU Title List / Page :9 RECORDINGS LISTINGS SEARCH TODAY :00AM :0AM bcd Nightline S WCVS :00 :5 : INFO Welcome to Using BOX GBS QBS Rainfield Charles Rose Fisher Everybody loves... Limpsons Dave Live Jay Lean Spin Town Bill & Greg / to select a TV program and press REC. Recording starts. Notes To record satellite TV programs, set a program recording manually. (next page) When you cannot download data of the TV program list, you can set a recording manually. (next page) To stop programed recording ) TV Guide. ) / / / to select a TV program currently being recorded. ) REC repeatedly until the recording icon disappears. 4

15 Getting more information on a TV program TV Guide. / to select a TV program. CONTENT MENU Title List / Page 8:0 Welcome to Using RECORDINGS Menu now for Listings Options Move to highlight any show Enter to tune to current show in glid Menu for more current show options LISTINGS TODAY :00AM :0AM bcd Nightline BOX Rainfield Limpsons GBS Dave Live Jay Lean QBS Charlie Rosa Fisher Spin Town Everybody loves... Bill & Greg SEARCH CONTENT MENU Title List / Page :9 RECORDINGS LISTINGS SEARCH TODAY :00AM :0AM Nightline bcd S WCVS :00 :5 : Welcome to Using BOX GBS QBS Rainfield Charles Rose Fisher Everybody loves... Limpsons Dave Live Jay Lean Spin Town Bill & Greg INFO INFO Setting program recording manually TV Guide. / to select SCHEDULE and press Menu. The Schedule Options menu appears. / to select new manual recording and press ENTER. The Record Options menu appears. 4 / to select an item for program recording. date: number buttons to enter the date (Month/Day/Year). start: number buttons and / to set the start time. end: number buttons and / to set the end time. Info to display the program s information. CONTENT MENU Title List / Page :9 RECORDINGS LISTINGS SEARCH TODAY :00AM :0AM Nightline bcd Welcome to Using S WCVS : BOX GBS QBS Rainfield Charles Rose Fisher Everybody loves... :00 :5 Limpsons Dave Live Jay Lean Spin Town Bill & Greg INFO 5 When channel: number buttons to select a channel. input: Select a recording source. TUNER-TV broadcasts Line,, -Satellite TV etc. recorder: / to select a recording media. quality: / to select a picture quality. O 4 frequency: / to select how often programed recording is executed. finishing the setting press ENTER. To return to the service menu Menu when choosing options of a service menu. 5

16 Using EASY NAVI Open EASY NAVI Main Menu, a main gate to the functions of this recorder. From this menu, you can access the desired functions. EASY NAVI. Sound is muted and the following GUI appears. (Actual displays vary depending on operational status.) Finder Cursor EASY NAVI Appears when the finder shows the current broadcast. Main Menu TV:ch /0/4 07:00am TV:8 (00:54:0) Play Time 00:0:5 TR Disc Time Slip Recorded title last selected TV Viewing TV Guide On Screen Play Contents DV Recording Delete Title Dubbing Finalize (R/RW) Format (RAM/RW) Setup / / / to select an item. Refer to the table below. ENTER. You can access the function. Functions Operating the finder (For the, DVD-RAM, DVD-R/RW recorded on this recorder and not finalized yet) ) When the cursor is on the finder, press /. You can view thumbnails of recorded contents. You can select the drive by pressing or DVD. ) When you find a desired content, press PLAY or ENTER. The content is played. ing ENTER enlarges the finder s playback picture to the full of the screen. ) To stop, press STOP. A current channel broadcast appears. ( TV:xxxch accompanies.) ing REC starts recording. Item TV Viewing Play Contents TV Guide On Screen DV Recording Delete Title Dubbing Finalize (R/RW) Format (RAM/RW) Setup Function Return to current broadcast channel. Recorded contents are listed in a thumbnail view. The TV Guide On Screen SCHEDULE appears. The setting menu for recording contents from equipment connected to the DV terminal. You can delete the current title displayed in the finder window. You can access a menu to dub the current content. You can execute the DVD-Video finalizing process on the loaded disc. You can format the loaded disc. A setup menu appears. Page* 60 (0) () () 4 7 * Pages in OPERATIONS GUIDE. ( ) in this booklet.