Component catalogue 2013

Transcription

1 Component catalogue 2013

2 Head Office Helvar Oy Ab Yrittäjäntie 23 FI Karkkila Finland Tel: United Kingdom Helvar Ltd Hawley Mill Hawley Road Dartford Kent, DA2 7SY United Kingdom Tel: +44 (0) Finland Helvar Oy Ab Vetotie 3 FI Vantaa Tel: Germany Helvar GmbH Philipp-Reis-Straße 4-8 DE Heusenstamm Germany Tel: +49 (0) 6104 / Italy Helvar S.r.l. Via W-Tobagi 26/1 IT Peschiera Borromeo (MI) Italy Tel: Sweden Helvar AB Åsögatan 155 SE Stockholm Sweden Tel: +46 (0) Hungary Helvar Kft. Lomb u. 31/b. HU-1139 Budapest Hungary Tel: Russia Representative Office of Helvar Oy Ab Sadovnicheskaya naberezhnaya Moscow Russia Tel: + 7 (495) France Helvar Bureau France 12 Allée Joséphine de Beauharnais FR Saint-Leu-la-Forêt France Tel: China Helvar Lighting (Suzhou) Co., Ltd. 15F International Building, 2 Suzhou Avenue West, SIP, Suzhou, Tel: Helvar has representatives all over the world. For additional information, please visit

3 LED drivers and accessories Dimmable constant current LED drivers 4 Non-dimmable constant current LED drivers 11 LED wiring & connectivity, dimensions 20 Accessories for Helvar LED drivers 24 1 Digital DALI controllable electronic ballasts EL-iDim for T5-fluorescent lamps 28 EL-iDim for T8-fluorescent lamps 30 EL-iDim, EL-iDim-c for Compact fluorescent lamps 32 Wiring diagrams & technical characteristics 33 Switch-Control information 35 Analogue (1-10 V) controllable electronic ballasts EL-sc for T5-fluorescent lamps 38 EL-sc for T8-fluorescent lamps 40 EL-sc for Compact fluorescent lamps 41 Wiring diagrams & technical characteristics 42 Switch-Control information 43 Standard electronic ballasts EL-ngn5, EL-s, EL-su for T5-fluorescent lamps 46 EL-s, EL-su EL-ngn, EL-es for T8-fluorescent lamps 52 EL-ngn5, EL-s, EL-TCs for Compact fluorescent lamps 55 Wiring diagrams & technical characteristics Electronic ballasts for HID-lamps EP-h Electronic ballasts for HID-lamps 67 5 Ballasts for fluorescent T8 s 230 V 50 Hz V 50 Hz V 50 Hz 75 Wiring diagrams, dimensions and delivery information 76 Ballasts for compact fluorescent lamps 230 V 50 Hz V 50 Hz 80 Wiring diagrams, dimensions and delivery information 81 Ballasts & ignitors for HID-lamps Ballasts for high pressure mercury lamps 84 Ballasts for high pressure sodium lamps 86 Power reduction ballasts for high pressure sodium 88 Ballasts for metal halide lamps 89 Ballasts for HID-lamps (220 V) 91 Wiring diagrams, dimensions and delivery information 92 Electronic superimposed pulse ignitors 94 General information and instructions for use Electronic ballasts 98 Magnetic ballasts 100 Quantity of ballasts for MCB s 102 Wire release instructions 108 EL-s wiring options 109 markings 110 Sensors idim Sense idim Concept 112 Minisensor3 Minisensor 116 SL-PIR-SW, SL-PIR-AN SL-MW-SW, µdim sensors SL-MW-AN, SL-MW-DA 117 MIMO2, MIMO3 MIMO2 Constant light sensor, MIMO3 sensor xxx TK V Ballast controller ballast compatibility & approvals 126 A

4 freedom in lighting LED Drivers Helvar s LED offering includes a range of Constant Current drivers including dimmable and nondimmable solutions. The LED drivers can be used for indoor and outdoor applications for spot lights, down lights, flood lights and linear strip lighting. The Helvar LED range is designed for easy installation and long life. All drivers provide power with high efficiency. The dimmable drivers ensure reliable and smooth dimming from 1 % %. Helvar s LED drivers are complemented by a full and compatible range of Helvar controls and sensor solutions, suitable for both luminaire based (μdim, idim, MIMO3) and networked applications (DIGIDIM Router). Outlook Further exciting LED product developments are in the pipeline for 2013, showing Helvar s continuous commitment to supporting luminaire manufacturers in making a successful transition to LED. Stay in tune with our website for continuous new LED products. 2

5 Helvar s LED drivers have been developed based on our expertise and knowledge of the key LED applications in the lighting market. Following look-up table provides an easy LED driver summary. The table links each LED driver to its typical application area. In addition it lists it control interface and maximum power rating. More detail can be found on the product pages. Driver type Switching 1-10 V DALI DMX Max.output Power LL6-U-CC LL20-U-CC LL1x20-E-DA LC1x30-E-CC LC1x30-E-AN LC1x30-E-DA LL1x40-E-CC LL1x40-E-DA LL2x35-E-CC x35 16 LL2x35-E-DA x35 9 LL1x70-E-CC LL1x70-E-DA OL1x60-E-CC OL1x100-E-CC OL1x100-E-CC LC50-U-DX To download the Helvar LEDesign calculator go to: Page 3

6 LL1x20-E-DA * 1x20 W Dimmable DALI LED driver Selectable constant current output: 350 / 500 / 700 ma Maximum 20 W load 20 W V, Hz DALI control input, 1 %-100 % dimming range Low stand-by power 0.3 W Protected up to 4 kv power network fast transients High efficiency, 0.86 * Preliminary information. For availability please check with your sales representative Connections Alternative parallel connection L N (+) I n Switch-Control DALI (-) I tot = 350 / 500 / 700 ma I 2 I 1 Note: Not suitable for load side switching operation. I fv = I 1 + I I n = 350 / 500 / 700 ma +/- 5% Mains Characteristics Voltage range DC range VAC VDC, starting voltage > 190 VDC Max mains current at full load A Frequency 0 / Hz U-OUTmax (abnormal) 80 V Stand-by power 0.3 W Load Output Output current 350 / 500 / 700 ma Max output power 20 W Efficiency, at full load, typical 0.86 I-OUT 350 ma 500 ma 700 ma P-out (max) 20 W 20 W 19.6 W U-OUT V V V λ 0.89c 0.92c 0.92c max Operating Conditions and Characteristics Max.temperature at tc point 75 C Ambient temperature range C Storage temperature range C Maximum relative humidity no condensation Life time h, at TC max (90 % survival rate) Connections and Mechanical Data Wire size mm 2 Wire type solid core and fine-stranded Maximum driver to LED wire length 5m Weight 110 g IP rating IP20 Conformity & Standards General and safety requirements EN Particular safety requirements for d.c. or a.c. supplied electronic controlgear for LED modules, acc. to EN Thermal protection class EN61347, C5e Mains current harmonics, acc. to EN Limits for Voltage Fluctuations and Flicker, acc to EN Radio Frequency Interference, acc. to EN Immunity standard, acc. to EN Performance requirements, acc to EN Digital adressing lighting interface (DALI) ** EN Compliant with relevant EU directives ENEC, CE & SELV marked ** with additional extensions Note: See page 22 for dimensions, (no. 2) 4

7 LC1x30-E-DA 1x30 W Dimmable DALI LED driver Selectable constant current output: 350 / 500 / 700 ma (custom currents on request) Maximum 30 W load DALI control input, 1 %-100 % dimming range Low stand-by power 0.3 W Protected up to 4 kv power network fast transients High efficiency, 0.86 Optional click-on strain relief for independent use External NTC thermal input idim compatible 30 W VAC, Hz Connections L N DALI Switch-Control Alternative parallel connection I n NTC I 2 (-) (+) I fv = 350 / 500 / 700 ma I 1 I fv I fv = I 1 + I I n = 350 / 500 / 700 ma +/- 5% Note: Not suitable for load side switching operation. Mains Characteristics Voltage range DC range VAC VDC, starting voltage > 190 VDC Max mains current at full load A Frequency 0 / Hz U-OUT max (abnormal) 80 V Stand-by power 0.3 W Load Output Output current (I-OUT) 350 / 500 / 700 ma (custom output currents ma on request) Max output power 30 W Efficiency, at full load, typical 0.86 I-OUT 350 ma 500 ma 700 ma P-out (max) 21 W 30 W 30 W U-OUT V V V λ 0.90c 0.94c 0.94c max Operating Conditions and Characteristics Max.temperature at tc point 75 C Ambient temperature range C * (* Independent use t a max = +45 C) Storage temperature range C Maximum relative humidity no condensation Life time h, at TC max (90 % survival rate) Connections and Mechanical Data Wire size mm 2 Wire type solid core and fine-stranded Maximum driver to LED wire length 5m (1 m with NTC) Weight 123 g (+17 g, strain relief LC1x30-SR) Thermal sensor input Input for external NTC thermal sensor NTC trigger point 8.2 kω IP rating IP20 Conformity & Standards General and safety requirements EN Particular safety requirements for d.c. or a.c. supplied electronic controlgear for LED modules, acc. to EN Thermal protection class EN61347, C5e Mains current harmonics, acc. to EN Limits for Voltage Fluctuations and Flicker, acc to EN Radio Frequency Interference, acc. to EN Immunity standard, acc. to EN Performance requirements, acc to EN Digital adressing lighting interface (DALI) ** EN Compliant with relevant EU directives ENEC, CE & SELV marked ** with additional extensions Note: See page 22 for dimensions, (no. 3 & 4) /1 5

8 LC1x30-E-AN 1x30 W 1x30 Вт Dimmable dimmbarer управляемый 1-10 ( V LED V) В LED driver светодиодный Konverter драйвер 1x30 W LED 1-10v 可调驱动 可选恒流输出电流 350 /500/ Selectable Выбор Einstellbarer выходного constant Konstantstrom: тока: current 350 output: / mA // /мА / / 700 ma ma 最大负载30w Maximale Maximum Last Максимальная 30 Wvon нагрузка load30 W 30 Вт 1-10 V 控制输入 调光范围1 %-100 % 1-10 диапазон V control VDC analoge яркости input, Steuerung, 1 1%-100 %-100%%Dimmbereich dimming range % 暂态过电压保护4kv 高压 高效率, 0.86 Protected Защита Kurzschlussfest отup пиковых to 4 kv скачков power network напряжения fast transients до 4 кв 卡扣式卡线槽可选用 High efficiency, Эффективность Schutz vor Netztransienten bis zu 4 KV 外接NTC负温度系数电阻补偿 Hohe Effizienz, click-on 0.86 Optional Прищёлкиваемый strain кабельный relief forзажим independent (заказывается use отдельно) 与MIMO3和 μdim 传感器兼容 WWВт VAC, VAC, В, Hz Hz Гц Optionale External Вход дляntc датчика Zugentlastung thermal температуры inputfür den unabhängigen Einsatz ansteckbar sensor compatible MIMO3 and μdim Совместим с датчиками MIMO3 и μdim NTC Eingang für Temperaturüberwachung Kompatibel mit MIMO3 und μdim Connections Схемы Schaltbild подключения 接线方式 Alternative parallel connection Parallelschaltung Alternative 可用并联接线 Расчёт тока L N 1-10 V NTC Home In Prev I2 Next (-) (+) I1 Ifv = 350 / 500 / 700 ma Ifv Ifv = I1 + I In = 350 / 500 / 700 ma +/- 5% Anmerkung: Der Lastausgang nicht geschaltet Note: Not suitable for load sidedarf switching operation.werden. 备注 不适合负载侧开关操作 Внимание: Выключатель в цепи светодиодов недопустим Netzeigenschaften Основные Mains Characteristics 电源特点 параметры Spannungsbereich Напряжение питания 电压范围 264VAC VAC- 264 В Voltage range VAC DC Постоянное Betrieb напряжение В, 直流范围 280VDC, VDC, DC range VDC, 开始电压 (Zündspannung запуск >при 190VDC) >VDC 190 В > 190 > VDC starting voltage 190 Макс. Max. Strom потребляемый at full ток А 满载时最大工作电流 ma Max mains current load mA A Frequenz Частота 00 // Hz / Гц 频率 Hz Hz Frequency (abnormal) 80 V Макс. выходное напряжение U-OUT 80 В 最大输出电压 非常态 80 (abnormal) 80 V U-OUT max max Lastausgang Выход 满载输出 Load Output 输出电流 (I-OUT) 500/350 / ma/ 700 ma Ausgangsstrom Выходной ток (I-OUT) (I-OUT) 350 / ma 500 ма Output current (I-OUT) 350 // 500 最大输出功率 30 W Макс. max. Ausgangsleistung выходная мощность 30 Вт W Max output power 30 W 满载时效率 Wert 0.86 нагрузка) Эффективность Effizienz bei 0.86 Efficiency, atvolllast, full (полн. load,typischer typical 0.86 I-OUT I-OUT I-OUT P-out (max) P-out P-out (макс) (max) U-OUT U-OUT U-OUT λ λ λ η@ max η@ max η η@@макс. max 350 ma ma ма 21 W WВ V V c 60 V 0.90c0.90c 0.90c ma ma ма 30 W WВ V V c 60 V 0.94c0.94c 0.94c ma ma ма 30 W WВ V V c 43 V 0.94c0.94c 0.94c Operating Conditions and Characteristics 正常工作条件和特点 Параметры at tc point 75 C Betriebsbedingungen Max.temperature 最高温度tc点 75 C Макс. Max.Temperatur температура amвtc точке Punkt tc 75 C Ambient temperature range 工作环境温度范围 C C* * Umgebungstemperaturbereich Окружающая температура * (* Independent use t = +45 C) C a max (* 独立使用 ta max = +45 C) = +45 C) (*unabhängige (* Выносной Montage монтаж t ta макс. = +45 C) Storage temperature range C a max C 储存温度范围 Lagertemperaturbereich C Температура хранения no Maximum relative humidity condensation 最大相对湿度 无凝结 Maximale Luftfeuchtigkeit keine Kondensation Макс. допустимая влажность без конденсации Life time h, at max 使用寿命 TC最高点 50TC000h Lebensdauer (90 % noch im Betrieb) h, bei Tc tc max Срок службы 000час, при макс. (90 % survival rate) (90 % 使用率) (10% смертность) 6 Подключение Verdrahtungand undmechanical mechanische Daten Connections Data 接线方式和技术参数 Провод Leitungsdurchmesser mm мм mm222 Wire size 0.5 接线尺寸 или mmодножильный Тип Leitungstyp провода гибкий Massivleitung oder feindrähtig Wire type solid core and fine-stranded 接线型号 实芯线 Макс. Maximale длина Leitungslänge проводов vom матрице Konverter5m 5м zur(1 м 5 m датчика (1 m NTC) mit NTC) Maximum driver to LED кwire length (1LED mдо with NTC) LED驱动的最长接线长度 5m (гр NTC 最长1m) Масса 126 Gewicht 126 Weight 126 gg 2 重量 126 g (+17гр (+17 g, g, кабель-зажим Zugenlastung LC1x30-SR) LC1x30-SR) (+17 strain relief LC1x30-SR) (+17 g, 卡线槽LC1x30-SR) Вход Eingang термодатчика NTC: Терморезистор Temperaturabschaltung Thermal sensor input Input for external(ntc) über 负温度系数输入 外部NTC负温度系数输入 Порог externen срабатывания 8.2 kω NTCsensor Sensor NTC thermal NTC 触发点 8.2 kω Класс NTC-Auslösepunkt IP IP20 8,2 kω kω NTC trigger point 8.2 IP 等级 IP20 IP rating Klasse IP20 IP20 IP Соответствие стандартам 一致性和标准性 Normenтребования & Standards Conformity & Standards Основные безопасности EN 总则和安全标准 EN Allgemeine und Sicherheitsstandard EN Основные требования безопасности, касающиеся General and safety requirements EN LED驱动特殊安全标准 EN Besondere Anforderungen an gleichoder электронных сонтроллеров для светодиодов EN Particular safety requirements for d.c. or a.c. supplied 热保护等级 EN61347, C5e wechselstromversorgte Класс термозащиты EN61347, C5e electronic controlgear forelektronische LED modules, acc. to EN 电流谐波 EN Betriebsgeräte für LED-Module Стабилизация напряжения EN Thermal protection class EN61347, C5e 电压波动和频闪限制 EN Temperaturschutz EN61347, C5e Допустимые EN Mains currentфлуктуации harmonics, питания acc. to EN 无线电频率干扰 EN Grenzwerte für Oberschwingungsströme Радиочастотные EN помехи Limits for Voltage Fluctuations and Flicker, acc to EN 绝缘标准 EN Begrenzung von Spannungsänderungen, Устойчивость EN Radio Frequency Interference, acc. to EN 性能标准 EN Spannungsschwankungen und Flicker Требования производительности EN Immunity standard, acc. to EN V 控制标准 EN Störaussendung EN В EN Performance requirements, acc to EN Störfestigkeit EN V Control acc. to EN 具备欧盟相关认证 Arbeitsweise EN Соответствие различным директивам ЕС ENEC, CE & SELV Compliant ENEC, CE и SELV отмечены with relevant EU directives 1-10 VDC analoge Steuerung EN ENEC, CE &der SELV marked Einhaltung entsprechenden EU-Richtlinien ENEC-, CE- und SELV-Kennzeichnung Note: Anmerkung: Размеры See page см.für на22стр. Abmessungen for dimensions, ( 3 3&и4) 4)siehe (no.seite 3 & 4)22 (3 und 4) 备注 尺寸详见P (no. Helvar данные Technische Data is subject могут Änderungen быть to change изменены vorbehalten. without безnotice. Weitere предварительного More Informationen information уведомления. finden at:sie auf подробнее unserer Internetseite см. 如有修改 恕不另行通知 更多信息请点击 /1

9 LL1x40-E-DA * 1x40 W Dimmable DALI LED driver Adjustable constant current output: 350 ma (default) ma DALI control input 1 % % dimming range Low standby power 0.4 W Protected up to 4 kv power network fast transients High efficiency, 0.89 Overload, open & short circuit protection Suitable for Class I, II or SELV luminaire External NTC thermal input Current setting resistor input Optional click-on strain relief for independent use * Preliminary information. For availability please check with your sales representative Connections 40 W VAC, Hz Alternative parallel connection In I fv = ma I2 I1 Switch-Control I fv = I 1 + I I n L N DALI Note: Not suitable for load side switching operation. R NTC Current setting (p.21) Resistor R output I fv open 350 ma 3.9 kω 500 ma 1.0 kω 700 ma 0 Ω 1050 ma Mains Characteristics Voltage range DC range VAC VDC, starting voltage > 190 VDC Max mains current at full load A Frequency 0 / Hz U-OUT max (abnormal) 100 V Stand-by power 0.4 W Load Output Output current (I-OUT) 350 ma (default) ma Max output power 40 W Efficiency, at full load, typical 0.89 I-OUT 350 ma 1050 ma P-out (max) 28 W 40 W U-OUT V V λ max Operating Conditions and Characteristics Max.temperature at tc point 75 C Ambient temperature range C * Storage temperature range C Maximum relative humidity no condensation Life time h, at TC max (90 % survival rate) Connections and Mechanical Data Wire size mm 2 Wire type solid core and fine-stranded Maximum driver to LED wire length 5m (1 m with NTC) Weight 150 g (+10 g, strain relief LL1x40-SR) Thermal sensor input Input for external NTC thermal sensor NTC trigger point 8.2 kω IP rating IP20 Conformity & Standards General and safety requirements EN Particular safety requirements for d.c. or a.c. supplied electronic controlgear for LED modules, acc. to EN Thermal protection class EN61347, C5e Mains current harmonics, acc. to EN Limits for Voltage Fluctuations and Flicker, acc to EN Radio Frequency Interference, acc. to EN Immunity standard, acc. to EN Performance requirements, acc to EN Digital adressing lighting interface (DALI) ** EN Compliant with relevant EU directives ENEC, CE & SELV marked * with additional extensions Note: See page 22 for dimensions, (no. 8) 7

10 LL1x70-E-DA 1x70 W Dimmable DALI LED driver Adjustable constant current output: 350 ma (default) ma Dali control input 1 %-100 % dimming range Low standby power 0,4 W Protected up to 4 kv power network fast transients Overload, short & open circuit protection Accept DC mains in case of central emergency battery High efficiency, > 0.91 Suitable for class I luminaires Current setting resistor input 70 W VAC Hz Connections I fv = ma L N R DA Switch-Control Note: Not suitable for load side switching operation. Driver output and current setting circuit are not isolated from mains Current setting (p. 21) Resistor R output I fv open 350mA 8.2 kω 500mA 0 Ω 700mA Mains Characteristics Voltage range DC range VAC VDC, starting voltage > 195 VDC Max mains current at full load A Frequency 0 / Hz U-OUT max (abnormal) 400 V Stand-by power 0.4 W Load Output Output current (I-OUT) 350 ma (default) ma Max output power 70 W Efficiency, at full load, typical 0.91 I-OUT 350 ma 700 ma P-out (max) 70 W 70 W U-OUT V V λ max Operating Conditions and Characteristics Max.temperature at tc point 75 C Ambient temperature range C * Storage temperature range C Maximum relative humidity no condensation Life time h, at TC max (90 % survival rate) Connections and Mechanical Data Maximum driver to LED wire length Weight IP rating Conformity & Standards 5 m 242 g IP20 General and safety requirements EN Particular safety requirements for d.c. or a.c. supplied electronic controlgear for LED modules, acc. to EN Thermal protection class EN61347, C5e Mains current harmonics, acc. to EN Limits for Voltage Fluctuations and Flicker, acc to EN Radio Frequency Interference, acc. to EN Immunity standard, acc. to EN Performance requirements, acc to EN Digital adressing lighting interface (DALI) * EN Compliant with relevant EU directives ENEC & CE marked * with additional extensions Note: See page 22 for dimensions, (no. 7) /1

11 LL2x35-E-DA * 2x35 W Dimmable DALI LED driver Adjustable constant current output: 350 ma (default) ma Two independent SELV rated output channels DALI control input 1 % % dimming range Low standby power 0,5 W Protected up to 4kV power network fast transients High efficiency, 0.9 Overload, open & short circuit protection Suitable for Class I or II luminaire External NTC thermal input Current setting resistor input 2x35 W VAC Hz * Preliminary information. For availability please check with your sales representative Connections I fv = ma L N DA Switch-Control Note: Not suitable for load side switching operation. Wrong wiring will serious damage the product PE needs not to be connected in class II luminaires if they are suitably designed NTC Current setting (p. 21) Resistor R output I fv open 350mA 0 Ω 700mA R Mains Characteristics Voltage range DC range VAC VDC, starting voltage > 190 VDC Max mains current at full load A Frequency 0 / Hz U-OUT max (abnormal) 120 V Stand-by power 0.5 W Load Output Output current (I-OUT) 350 ma (default) ma Max output power 35 W / channel Efficiency, at full load, typical 0.9 I-OUT 350 ma 700 ma P-out (max) / channel 35 W / ch 35 W / ch U-OUT V V λ (both channels loaded) η (both ch max) Operating Conditions and Characteristics Max.temperature at tc point 80 C Ambient temperature range C Storage temperature range C Maximum relative humidity no condensation Life time h, at TC max (90 % survival rate) Connections and Mechanical Data Maximum driver to LED wire length Weight IP rating NTC trigger point Conformity & Standards 5 m 365 g IP kω General and safety requirements EN Particular safety requirements for d.c. or a.c. supplied electronic controlgear for LED modules, acc. to EN Thermal protection class EN61347, C5e Mains current harmonics, acc. to EN Limits for Voltage Fluctuations and Flicker, acc to EN Radio Frequency Interference, acc. to EN Immunity standard, acc. to EN Performance requirements, acc to EN Digital adressing lighting interface (DALI) ** EN Compliant with relevant EU directives ENEC,CE & SELV marked ** with additional extensions Note: See page 22 for dimensions, (no. 8) 9

12 LC50-U-DX3 3 channel DMX LED driver 50 W Max. total output power 50 W Smooth dimming range 0.1 % % 50 W V, Hz Default output current 350 ma Programmable output current ( ma) Programmable DMX512 start address Optional DMX programming dongle (LC50-PR) High efficiency, 0.89 (at full load, 230 VAC) High power factor > 0.97c (at full load, 230 VAC) Connections (+) Ch1 (-) (+) Ch2 (-) (+) Ch3 (-) (+) NTC (-) (+) DMX in (-) (shield) GND L N NTC DMX in (+) DMX in (-) DMX in (shield) L N Note: Not suitable for load side switching operation. Mains Characteristics Voltage range Max mains current at full load Frequency U-OUT max (abnormal) Load Output VAC A 50 / 60 Hz 60 V Output current (default) 350 ma Output current range (programmable) ma Max. total output power 50 W Max. individual channel power 50 W Efficiency, at full load, typical 0.89 I-OUT 350 ma ma P-out (max) 50 W 50 W U-OUT V V λ > 0.9c > 0.9c max Operating Conditions and Characteristics Max.temperature at tc point 85 C Ambient temperature range C Storage temperature range C Maximum relative humidity no condensation Life time h, at tc max. (90 % survival rate) Connections and Mechanical Data Wire size mm 2 Wire type solid core and fine-stranded Maximum driver to LED wire length 5 m Weight 350 g IP rating 20 Conformity & Standards General and safety requirements EN Particular safety requirements for d.c. or a.c. supplied electronic controlgear for LED modules, acc. to EN Thermal protection class EN 61347, C5e Mains current harmonics, acc. to EN Radio Frequency Interference, acc. to EN Immunity standard, acc. to EN Performance requirements, acc to EN Compliant with relevant EU directives CE, UL pending, VDE & ENEC pending, SELV Optional USB to DMX programming dongle LC50-PR 10 Note: See page 22 for dimensions, (no. 5) /1

13 LL6-U-CC 1x6 W Constant Current LED driver Selectable constant current output: 350 / 700 ma Universal supply voltage range Short circuit protection Protected up to 4 kv power network fast transients High efficiency, 0.80 Linear enclosure with strain relief for independent use Accepts DC mains in case of central emergency battery 6 W V, Hz Connections Alternative parallel connection I n (-) I 2 I 1 I tot = 350 / 700 ma L N (+) I fv I fv = I 1 + I I n = 350 / 700 ma +/- 5% Note: Not suitable for load side switching operation. Mains Characteristics Voltage range Max mains current at full load Frequency Maximum circuit power U-OUT max (abnormal) Load Output VAC VDC 50 ma (at 240 VAC) 140 ma (at 100 VAC) 0 / Hz 9 W 25 V Output current 350 / 700 ma Efficiency, at full load, typical 0.80 Max output power 7.0 W I-OUT 350 ma 700 ma P-out (max) 5.6 W 7.0 W U-OUT λ max Operating Conditions and Characteristics Max.temperature at tc point 80 C Ambient temperature range C Storage temperature range C Maximum relative humidity no condensation Life time h, at tc max (90 % survival rate) Connections and Mechanical Data Wire size mm 2 Wire type solid core and fine-stranded Maximum driver to LED wire length 5 m Weight 65 g IP rating 20 Conformity & Standards General and safety requirements EN Particular safety requirements for d.c. or a.c. supplied electronic controlgear for LED modules, acc. to EN Thermal protection class EN61347, C5e Mains current harmonics, acc. to EN Limits for Voltage Fluctuations and Flicker, acc to EN Radio Frequency Interference, acc. to EN Immunity standard, acc. to EN Performance requirements, acc to EN Compliant with relevant EU directives ENEC, CE & SELV marked Note: See page 22 for dimensions, (no. 1) /1 11

14 LL20-U-CC 1x20 W Constant Current LED driver Selectable constant current output: 350 / 700 ma Universal supply voltage range 20 W V, Hz Short circuit protection Protected up to 4 kv power network fast transients High efficiency, 0.86 Linear enclosure with strain relief for independent use Accepts DC mains in case of central emergency battery Connections L N 2 A max (+) Alternative parallel connection I n (-) Supply Voltage Chaining* (only LL20-U-CC) I tot = 350 / 700 ma I 2 I 1 I fv = I 1 + I I n = 350 / 700 ma +/- 5% * max number of converters depends on supply voltage and load (7 pcs. max at full load) Note: Not suitable for load side switching operation. Mains Characteristics Voltage range Max mains current at full load Frequency Maximum circuit power U-OUT max (abnormal) Load Output VAC VDC 100 ma (at 240 VAC) 230 ma (at 100 VAC) 0 / Hz 23 W 50 V Output current 350 / 700 ma Efficiency, at full load, typical 0.86 Max output power 20 W I-OUT 350 ma 700 ma P-out (max) 15 W 20.3 W U-OUT λ max Operating Conditions and Characteristics Max.temperature at tc point 80 C Ambient temperature range C Storage temperature range C Maximum relative humidity no condensation Life time h, at TC max (90 % survival rate) Connections and Mechanical Data Wire size mm 2 Wire type solid core and fine-stranded Maximum driver to LED wire length 5m Weight 110 g IP rating 20 Conformity & Standards General and safety requirements EN Particular safety requirements for d.c. or a.c. supplied electronic controlgear for LED modules, acc. to EN Thermal protection class EN61347, C5e Mains current harmonics, acc. to EN Limits for Voltage Fluctuations and Flicker, acc to EN Radio Frequency Interference, acc. to EN Immunity standard, acc. to EN Performance requirements, acc to EN Compliant with relevant EU directives ENEC, CE & SELV marked 12 Note: See page 22 for dimensions (no.2) /1

15 LC1x30-E-CC 1x30 W Constant Current LED driver Selectable constant current output: 350 / 500 / 700 ma (fixed) Maximum 30 W load Short circuit protection High efficiency, 0.86 Optional click-on strain relief for independent use External NTC thermal input Protected up to 4 kv power network fast transients 30 W VAC, Hz Connections L N Alternative parallel connection I n NTC I 2 (-) (+) I fv = 350 / 500 / 700 ma I 1 I fv I fv = I 1 + I I n = 350 / 500 / 700 ma +/- 5% Note: Not suitable for load side switching operation. Mains Characteristics Voltage range DC range VAC VDC, starting voltage > 190 VDC Max mains current at full load A Frequency 0 / Hz U-OUT max (abnormal) 80 V Load Output Output current (I-OUT) 350 / 500 / 700 ma Max output power 30 W Efficiency, at full load, typical 0.86 I-OUT 350 ma 500 ma 700 ma P-out (max) 21 W 30 W 30 W U-OUT V V V λ 0.93c max Operating Conditions and Characteristics Max.temperature at tc point 75 C Ambient temperature range C * (* Independent use t a max = +45 C) Storage temperature range C Maximum relative humidity no condensation Life time h, at TC max (90 % survival rate) Connections and Mechanical Data Wire size mm 2 Wire type solid core and fine-stranded Maximum driver to LED wire length 5m (1 m with NTC) Weight 115 g (+17 g, strain relief LC1x30-SR) Thermal sensor input Input for external NTC thermal sensor NTC trigger point 8.2 kω IP rating IP20 Conformity & Standards General and safety requirements EN Particular safety requirements for d.c. or a.c. supplied electronic controlgear for LED modules, acc. to EN Thermal protection class EN61347, C5e Mains current harmonics, acc. to EN Limits for Voltage Fluctuations and Flicker, acc to EN Radio Frequency Interference, acc. to EN Immunity standard, acc. to EN Performance requirements, acc to EN Compliant with relevant EU directives ENEC, CE & SELV marked Note: See page 22 for dimensions (no. 3 & 4) /1 13

16 LL1x40-E-CC * 1x40 W Constant Current LED driver Adjustable constant current output: 350 ma (default) ma Protected up to 4kV power network fast transients 40 W VAC Hz High efficiency, 0.89 Overload, open & short circuit protection Suitable for Class I, II or SELV luminaire External NTC thermal input Current setting resistor input * Preliminary information. For availability please check with your sales representative Connections In I2 I fv = ma I1 I fv = I 1 + I I n L N Note: Not suitable for load side switching operation. R NTC Current setting (p.21) Resistor R output I fv open 350 ma 3.9 kω 500 ma 1.0 kω 700 ma 0 Ω 1050 ma Mains Characteristics Voltage range DC range VAC VDC, starting voltage > 190 VDC Max mains current at full load A Frequency 0 / Hz U-OUT max (abnormal) 100 V Load Output Output current (I-OUT) 350 ma (default) ma Max output power 40 W Efficiency, at full load, typical 0.89 I-OUT 350 ma 1050 ma P-out (max) 28 W 40 W U-OUT V V λ max Operating Conditions and Characteristics Max.temperature at tc point 75 C Ambient temperature range C Storage temperature range C Maximum relative humidity no condensation Life time h, at TC max (90 % survival rate) Connections and Mechanical Data Wire size mm 2 Wire type solid core and fine-stranded Maximum driver to LED wire length 5m (1 m with NTC) Weight 150 g (+17 g, strain relief LL1x40-SR) Thermal sensor input Input for external NTC thermal sensor NTC trigger point 8.2 kω IP rating IP20 Conformity & Standards General and safety requirements EN Particular safety requirements for d.c. or a.c. supplied electronic controlgear for LED modules, acc. to EN Thermal protection class EN61347, C5e Mains current harmonics, acc. to EN Limits for Voltage Fluctuations and Flicker, acc to EN Radio Frequency Interference, acc. to EN Immunity standard, acc. to EN Performance requirements, acc to EN Compliant with relevant EU directives ENEC, CE & SELV marked Note: See page 22 for dimensions, (no.6) 14

17 LL1x70-E-CC 1x70 W Constant Current LED driver Overload, short & open circuit protection Suitable for class I luminaires 70 W VAC Hz Adjustable constant current output: 350 (default) to 700 ma Maximum 70 W load Accept DC mains in case of central emergency battery High efficiency > 0.91 Protected up to 4 kv power network fast transients Suitable for Class I luminaires Current setting resistor input Connections I fv = ma L N R Note: Not suitable for load side switching operation. Driver output and current setting circuit are not isolated from mains Mains Characteristics Voltage range DC range VAC VDC, starting voltage > 195 VDC Max mains current at full load A Frequency 0 / Hz U-OUT max (abnormal) 400 V Load Output Output current (I-OUT) 350 (default) to 700 ma Max output power 70 W Efficiency, at full load, typical > 0.91 I-OUT 350 ma 700 ma P-out (max) 70 W 70 W U-OUT V V λ max Operating Conditions and Characteristics Max.temperature at tc point 75 C Ambient temperature range C Storage temperature range C Maximum relative humidity no condensation Life time h, at TC max (90 % survival rate) Connections and Mechanical Data Wire size mm 2 Wire type solid core and fine-stranded Maximum driver to LED wire length 5 m Weight 227 g IP rating IP20 Conformity & Standards General and safety requirements EN Particular safety requirements for d.c. or a.c. supplied electronic controlgear for LED modules, acc. to EN Thermal protection class EN61347, C5e Mains current harmonics, acc. to EN Limits for Voltage Fluctuations and Flicker, acc to EN Radio Frequency Interference, acc. to EN Immunity standard, acc. to EN Performance requirements, acc to EN Compliant with relevant EU directives ENEC & CE marked Current setting (p. 21) Resistor R output I fv open 350mA 8.2 kω 500mA 0 Ω 700mA Note: See page 23 for dimensions (no.7) /1 15

18 LL2x35-E-CC * 2x35 W Constant Current LED driver Adjustable constant current output: 350 ma (default) ma Two independent SELV rated output channels Protected up to 4 kv power network fast transients High efficiency 0.91 overload open & short circuit protection Suitable for Class I or II luminaire External NTC thermal input Current setting resistor input 2x35 W VAC, Hz * Preliminary information. For availability please check with your sales representative. Connections I fv = ma L N R Note: Not suitable for load side switching operation. Wrong wiring will serious damage the product PE needs not to be connected in class II luminaires if they are suitably designed NTC Current setting (p. 21) Resistor R output I fv open 350mA 0 Ω 700mA Mains Characteristics Voltage range DC range VAC VDC, starting voltage > 190 VDC Max mains current at full load A Frequency 0 / Hz U-OUT max (abnormal) 120 V Load Output Output current (I-OUT) 350 ma (default) ma Max output power 35 W / channel Efficiency, at full load, typical 0.91 I-OUT 350 ma 700 ma P-out (max) / channel 35 W / ch 35 W / ch U-OUT V V λ (both channels loaded) η (both ch max) Operating Conditions and Characteristics Max.temperature at tc point 80 C Ambient temperature range C Storage temperature range C Maximum relative humidity no condensation Life time h, at TC max (90 % survival rate) Connections and Mechanical Data Maximum driver to LED wire length Weight IP rating NTC trigger point Conformity & Standards 5 m 365 g IP kω General and safety requirements EN Particular safety requirements for d.c. or a.c. supplied electronic controlgear for LED modules, acc. to EN Thermal protection class EN61347, C5e Mains current harmonics, acc. to EN Limits for Voltage Fluctuations and Flicker, acc to EN Radio Frequency Interference, acc. to EN Immunity standard, acc. to EN Performance requirements, acc to EN Compliant with relevant EU directives ENEC,CE & SELV marked Note: See page 23 for dimensions, (no. 8) 16

19 OL1x60-E-CC 1x60 W Constant Current LED driver Selectable constant current output: 350 / 700 / 1400 ma Maximum 63 W load Short circuit protection Open circuit protection Protected up to 4 kv power network fast transients High efficiency > 0.90 Suitable for outdoor use IP65 Double insulated enclosure 60 W VAC, Hz 17 Connections Alternative parallel connection I n L N E (+) (-) I tot = 350 / 700 / 1400 ma I 2 I 1 I fv Note: Not suitable for load side switching operation. I fv = I 1 + I I n = 350 / 700 / 1400 ma +/- 5% Mains Characteristics Voltage range VAC Max mains current at full load A Frequency Hz U-OUT max (abnormal) 113 V Load Output Output current (I-OUT) 350 / 700 / 1400 ma Max output power 63 W Efficiency, at full load, typical 0.9 I-OUT 350 ma 700 ma 1400 ma P-out (max) 31.5 W 63 W 58.8 W U-OUT V V V λ 0.94c max Operating Conditions and Characteristics Max.temperature at tc point 85 C Ambient temperature range C Storage temperature range C Maximum relative humidity 100 % Life time: h, at 75 C TC h, at 85 C TC (90 % survival rate) Connections and Mechanical Data Connection wires length Maximum driver to LED wire length Weight IP rating Conformity & Standards 0.3 m 5 m 490 g IP65 General and safety requirements EN Particular safety requirements for d.c. or a.c. supplied electronic controlgear for LED modules, acc. to EN Thermal protection class EN61347, C5e Mains current harmonics, acc. to EN Limits for Voltage Fluctuations and Flicker, acc to EN Radio Frequency Interference, acc. to EN Immunity standard, acc. to EN Performance requirements, acc to EN Compliant with relevant EU directives ENEC, CE & SELV marked Note: See page 23 for dimensions(no. 9) /1 17

20 OL1x100-E-CC1 1x100 W Constant Current LED driver Selectable constant current output: 700 / 1050 ma Maximum 105 W load Short circuit protection Open circuit protection Protected up to 4 kv power network fast transients High efficiency > 0.91 Suitable for outdoor use IP65 Double insulated enclosure 100 W VAC, Hz 18 Connections Alternative parallel connection I n L N E (+) (-) I tot = 700 / 1050 ma I 2 I 1 I fv I fv = I 1 + I I n = 700 / 1050 ma +/- 5% Note: Not suitable for load side switching operation. Mains Characteristics Voltage range VAC Max mains current at full load A Frequency Hz U-OUT max (abnormal) 144 V Connections and Mechanical Data Connection wires length Maximum driver to LED wire length Weight IP rating 0.3 m 5 m 750 g IP65 Load Output Output current (I-OUT) 700 / 1050 ma Max output power 105 W Efficiency, at full load, typical 0.91 I-OUT 700 ma 1050 ma P-out (max) 84 W 105 W U-OUT V V λ max Operating Conditions and Characteristics Max.temperature at tc point 85 C Ambient temperature range C Storage temperature range C Maximum relative humidity 100 % Life time: h, at 75 C TC h, at 85 C TC (90 % survival rate) Conformity & Standards General and safety requirements EN Particular safety requirements for d.c. or a.c. supplied electronic controlgear for LED modules, acc. to EN Thermal protection class EN61347, C5e Mains current harmonics, acc. to EN Limits for Voltage Fluctuations and Flicker, acc to EN Radio Frequency Interference, acc. to EN Immunity standard, acc. to EN Performance requirements, acc to EN Compliant with relevant EU directives ENEC & CE marked 18 Note: See page 22 for dimensions (no. 10) /1

21 OL1x100-E-CC2 1x100 W Constant Current LED driver Selectable constant current output: 1400 / 2100 ma Maximum 101 W load Short circuit protection Open circuit protection Protected up to 4 kv power network fast transients High efficiency > 0.91 Suitable for outdoor use IP65 Double insulated enclosure 100 W VAC, Hz 18 Connections Alternative parallel connection I n L N E Note: Not suitable for load side switching operation. (+) (-) I tot = 1400 / 2100 ma I 2 I 1 I fv I fv = I 1 + I I n = 1400 / 2100 ma +/- 5% Mains Characteristics Voltage range VAC Max mains current at full load A Frequency Hz U-OUT max (abnormal) 92 V Connections and Mechanical Data Connection wires length Maximum driver to LED wire length Weight IP rating 0.3 m 5 m 750 g IP65 Load Output Output current (I-OUT) 1400 / 2100 ma Max output power 101 W Efficiency, at full load, typical 0.91 I-OUT 1400 ma 2100 ma P-out (max) 101 W 101 W U-OUT V V λ max Operating Conditions and Characteristics Max.temperature at tc point 85 C Ambient temperature range C Storage temperature range C Maximum relative humidity 100 % Life time: h, at 75 C TC h, at 85 C TC (90 % survival rate) Conformity & Standards General and safety requirements EN Particular safety requirements for d.c. or a.c. supplied electronic controlgear for LED modules, acc. to EN Thermal protection class EN61347, C5e Mains current harmonics, acc. to EN Limits for Voltage Fluctuations and Flicker, acc to EN Radio Frequency Interference, acc. to EN Immunity standard, acc. to EN Performance requirements, acc to EN Compliant with relevant EU directives ENEC & CE marked Note: See page 22 for dimensions (no. 10) /1 19

22 LED wiring & connectivity Helvar have a range of LED drivers suited for either in-built and independent luminaire usage. In order to have safe and reliable LED driver operation, the LED luminaires will need to comply with the relevant standards and regulations (e.g. IEC/EN ). The LED luminaire shall be designed to adequately protect the LED drivers from dust, moisture and pollution. The luminaire manufacturer is responsible for the correct choice and installation of the LED drivers according to the application and product datasheets. Specifications of the LED drivers may never exceed the operating conditions as per the product datasheets. Wiring considerations Installation & operational considerations Wire type and cross section Please refer to datasheets connections & mechanical data Wiring insulation According to recommendations in EN Maximum wire lengths Please refer to datasheets connections & mechanical data Wire connections Please refer to datasheets connections diagram Miniature Circuit Breakers (MCB) Type-C MCB s with trip characteristics in according to EN are recommended. Please refer to page 102 for the exact maximum number of LED drivers per MCB. LED driver earthing LED drivers are designed to support different luminaire classifications, like Class I or Class II fittings (no earth required). Please check the individual LED driver type for its exact safety class rating. For Helvar LED drivers to have a reliable operation and EMC performance, the luminaires are expected to have an earth connection. When using a SELV-rated LED driver, then the SELV driver output has to be insulated from the luminaire earth connection (ref. EN luminaire standard). Maximum tc temperature Reliable operation and lifetime is only guaranteed if the maximum tc point temperature is not exceeded under the conditions of use. Strain Relief for independent use Some of the Helvar LED drivers allow use both inside the luminaire and outside the luminaire, via a strain relief. The strain relief provides reliable fastening method for the mains and LED output wiring. Ensure that the LED driver does not exceed temperature higher than specified on the product datasheets. The general preferred installation position of LED drivers is to have the top cover facing upwards. Switch-Control The Helvar DALI dimmable LED drivers feature Switch-Control. This feature provides basic On/Off and Up/Down dimming functionality through a standard momentary switch. Switch-Control and DALI controls may not be connected simultaneously. For more accurate Switch-Control operational information please refer to page 35 (EB section) L N Switch-Control 20 T A /2

23 Current setting resistor The Helvar LL1x40, LL1x70 and LL2x35 driver platforms feature an adjustable constant current output. An external resistor can be inserted in to the current setting terminal, allowing the user to adjust the LED driver output current. When no external resistor is connected, then the LED drivers will operate at their default lowest current level. A standard through-hole resistor can be used for the current setting. To achieve the most accurate output current it is recommended to select a quality low tolerance resistor. When bending the external resistor, then please handle carefully to avoid damaging the component (see picture right). For the resistor / current value selection, please refer to the enclosed tables below. LL1x70- & LL2x35- R (Ω) 0 1k 1k2 1k5 1k8 2k2 2k7 3k3 3k9 4k7 5k6 6k8 8k2 10k 12k 15k 22k 27k 33k 39k 47k 56k 68k 82k 100k 150k 330k 1M I out (ma) T A /2 21

24 Dimensions With strain relief (LL1x40-SR) T A /2

25 ± ± ± ± LL6-U-CC 2 LL20-U-CC, LL1x20-E-DA 3 LC1x30-E-CC, LC1x30-E-DA, LC1x30-E-AN 4 LC1x30-E-CC, LC1x30-E-DA, LC1x30-E-AN (+ LC1x30-SR) 5 LC50-U-DX3 6 LL1x40-E-CC, LL1x40-E-DA (+ LL1x40-SR) 7 LL1x70-E-CC, LL1x70-E-DA 8 LL2x35-E-CC, LL2x35-E-DA 9 OL1x60-E-CC 10 OL1x100-E-CC1, OL1x100-E-CC2 T A /2 23

26 LED driver accessories LC1x30-SR Easy to assemble click-on strain relief for LC1x30 series Allows independent driver usage Screws for internal cable clamps included Cable clamps allowing different cable thicknesses LL1x40-SR Easy to assemble click-on strain relief for LL1x40 series Allows independent driver usage Screws for internal cable clamps included Cable clamps allowing different cable thicknesses Each pack includes 2 x strain reliefs LC50-PR USB to DMX programming dongle for the LC50-U-DX3 Configuring the LED driver parameters Setting the LED driver DMX start address Helvar DMX LED configurator Software downloadable from: For more information please see Technical note LED-TN-005 LC50-U-DX3 Operational & Configuration information 24

27 25

28 freedom in lighting electronic BALLASTS One of the first companies to develop and manufacture electronic ballasts, Helvar s history in these products extends back to the early 1980s. Since that time, Helvar has remained at the forefront, offering a comprehensive range of innovative electronic ballasts covering all relevant applications with T5, T8 and compact fluorescent lamps. The tables below show lamp categories where ballast combinations are found. Page For T5 lamps For T8 lamps For compact lamps For HID lamps Digital DALI electronic ballasts EL-iDim EL-iDim-c Analogue controllable electronic ballasts EL-sc STANDARD electronic BALLASTS EL-s EL-su EL-ngn EL-ngn EL-es EL-TCs EP-h

29 DALI electronic ballasts EL-iDim / EL-iDim-c DALI ballasts are designed for a broad range of applications from the smallest intelligent luminaires to major lighting installations in large building complexes. What s more, they offer the important advantage of enabling everything to be achieved with the same ballasts. EL-iDim / EL-iDim-c DALI ballasts are also fully compatible with Helvar idim sensors, the combination creating the latest high-tech innovation available to the lighting market. With out-of-box functionality, the Helvar system is moreover, easy to install and use, and maintenance costs are always kept to a minimum. In the design of EL-iDim / EL-iDim-c, customer input played a crucial role leading to superior features such as: OCC technology, guaranteeing the highest possible: EEI = A1 BAT Remarkable low stand-by power Smooth and stepless dimming from 100 % to 1 % Multi-lamp operation, allowing one ballast to drive all HE-T5 lamps Multi-lamp operation between several compact lamps EL-iDim-c ballast are suitable for use both in single and twin lamp operation The ballasts also have an in-built data register capable of storing information on running hours, energy consumption, mains voltage, lamp voltage etc. This can be very useful in large installations where the lighting management and maintenance is centralized in one monitoring room. OCC TM - Optimum CATHODE CONTROL The proven OCC TM - Optimum Cathode Control technology used in Helvar EL-s, EL-sc, EL-iDim and EL-TCs electronic ballast ranges. OCC TM ensures that the electrical parameters supplied to the lamp are always optimum, minimising system losses and maximising lamp lifetime. The achieved energy saving is considerable compared to existing ballasts on the market. 27