BNI EIP Z009 IP67 Module, Unmanaged Switch

Transcription

1 BNI EIP Z009 IP67 Module, Unmanaged Switch

2 Balluff Ethernet IP, BNI EIP Z016 1 Notes to the User 1.1 About this guide Structure of the guide Typgraphical Conventions Symbols Abbreviations 2 2 Safety 2.1 Intended Use General Safeety Notes Meaning of the warnings 3 3 Getting Started 3.1 Connection overview Mechanical connection Electrical connection Ethernet connection Connecting sensors 5 4 Technical Data 4.1 Dimensions Mechanical Data Operating conditions Electrical Data Ethernet Port Function Indicators 7 5 Included Material 5.1 Included Material 17 6 Appendix Ordering code 18 Bit Layout 18

3 1 Notes to the User 1.1 About this guide This guide describes the Balluff Ethernet IP Fieldbus Module BNI EIP-, which enables expanded communication down to the lowest level so as to provide improved process optimizing and preventive maintenance. This module is IP67 protected and features a rugged metal IP67 housing. The device is ideal for use in harsh industrial environments. 1.2 Structure of the guide 1.3 Typographical Conventions Syntax Cross-references The Guide is organized so that the sections build on one another. Section 2. Basic safety informations. Section 3: The main steps for installing the device. Section 4: Technical data for the device. The following typographical conventions are used in this Guide. Numbers Decimal numbers are shown without additional indicators (e.g. 123), Hexadecimal numbers are shown with the additional indicator hex (e.g. 00hex). Cross-references indicate where further information on the topic can be found ("see Section 4.2 ). 1.4 Symbols Note, tip This symbol indicates general notes. 1.5 Abbreviations BNI Balluff Network Interface EIP Ethernet IP EMC Electromagnetic Compatibility FE Function Ground Attention! This symbol in connection with the word "Attention" warns of a possible hazardous situation for the health of persons or for equipment damage. Disregard of these warning notes may result in injury or damage to equipment. Always observe the described measures for preventing this danger. 2

4 2 Safety 2.1 Intended Use The BNI EIP- serves as a unmanaged switch module for connecting to a Ethernet IP network. 2.2 General Safety Notes Installation and startup Installation and startup are to be performed only by trained personnel. Any damage resulting from unauthorized manipulation or improper use voids the manufacturer's guarantee and warranty. The device is an equipment in accordance with EMC Class A. Such equipment may generate RF noise. The operator is responsible for taking the appropriate measures before using. The device may be operated only using an approved power supply (see 4 Technical Data ). Only approved cables may be used. 2.3 Meaning of the warnings Operation and testing The operator is responsible for ensuring that local prevailing safety regulations are followed. When defects and non-clearable faults in the device occur, take it out of service and secure against unauthorized use. Approved use is ensured only when the housing is fully installed. Caution! This symbol in connection with the word "Caution" warns of a possible hazardous situation for the health of persons or for equipment damage. Disregard of these warning notes may result in injury or damage to equipment. Always observe the described measures for preventing this danger. 3

5 3 Getting Started 3.1 Connection Overview Connection overview BNI EIP Z009 1 Mounting hole 2 Port label 3 Status LED 4 Ethernet IP Port 5 5 Ethernet IP Port 6 6 Ethernet IP Port 7 7 Ethernet IP Port 8 8 Ethernet IP Port 4 9 Ethernet IP Port 3 10 Ethernet IP Port 2 11 Ethernet IP Port 1 12 Power supply 13 Ethernet IP Uplink Port 4

6 3 Getting Started 3.2 Mechanical connection 3.3 Electrical connection Supply voltage The module is attached using 2 M6 screws and 2 washers. Isolation pad as accessory available Power (7/8 Mini 4-pin plug) PIN Signal Demand V Output Power V Input Power (not used for the 8 O modules) 3 0 V Input Power Common 4 0 V Output Power Common 24 V DC. Total current <9A. The total current of all modules may not exceed 9A even when daisy chaining the actuator supply. Function ground Note! The FE connection from the housing to the machine must be low-impedance and kept as short as possible. 3.4 Ethernet Connection The Ethernet connection is made using the M12 females (D-coded). Ethernet Port: (M12, D-coded, female) PIN Requirement 1 Tx+ 2 Rx+ 3 Tx- 4 Rx- 5

7 4 Technical Data 4.1 Dimensions 4.2 Mechanical Data Housing material Die-case zinc, matte nickel plated Enclosure rating per IEC IP 67 (only when plugged-in and threaded-in) Supply voltage 7/8 4-pin male Dimensions (W x H x D in mm) 68 x 224 x 30.9 Mounting type 2-hole screw mount Ground strap attachment M4 Weight Approx. 580gr. 4.3 Operating conditions Operating temperature T a Storage temperature EMC - EN /3/4/5/6 - EN C C -25 C C - Severity level 4A/3A/4B/2A/3A - Gr.1, CL. A Shock/vibration EN , EN EN , EN Electrical Data Supply voltage V DC, per EN Ripple <1% Input current at 24 V 130 ma 6

8 4 Technical Data 4.5 Ethernet Port Ethernet IP Uplink port 1 x 10Base-/100Base-Tx Connection for Ethernet IP Uplink port Standard Ethernet IP ports Connection for standard Ethernet ports Cable types per IEEE Data transmission rate Max. cable length Flow control M12, D-coded 8 x 10Base-/100Base-Tx M12, D-coded Shielded twisted pair, min. STP CAT 5/ STP CAT 5e 10/100 Mps 100 m Half Duplex/Full Duplex (IEEE x- Pause) 4.6 Function Indicators LED indicators Ethernet IP / module LED 1-9: Indication: Module / Uplink port Port LED: Link Port LED: Data transmission rate LED Indicator Function LED 1 Green/Red Power Status LED 4 Red/Off Module Status LED 7 Yellow/Off Data transfer Uplink port active/inactive LED 9 Yellow/Off Data trans. Rate Uplink port: 100Mbit/s / 50 Mbit/s LED indicators ports Each M12 Port is assigned two 2-color LEDs which indicate the configuration or operating states. LED LNK Off Yellow Green blinking LED 100 Yellow/Off Function LED Ethernet link is inactive Ethernet link is active Data transfer is active Data trans. Rate: 100 Mibit/s / 50 Mbit/s 7

9 5 Included Material 5.1 Included Material The BNI EIP consists of the following components: IO-block 4 blind plugs M12 Ground strap Screw M4x6 20 labels 8

10 6 Appendix Ordering code BNI EIP Z009 Balluff Network Interface IO-Link interface Functions 950 = IP 67 module, unmanaged switch Variant 000 = Standard version Mechanical version Z009 = Die-cast zinc housing Material: 1. Balluff housing version Uplink: 1 x M12x1 internal thread Power: 7/8 external thread Ethernet Ports: 8 x M12x1 internal thread 9

11 Balluff GmbH Schurwaldstrasse Neuhausen a.d.f. Germany Tel Fax balluff@balluff.de ν