TIEROD CYLINDER. Ecological cylinder with compact switch SCG SERIES. Variations added CC-780A 4

Transcription

1 IEROD YLIDER S SERIES Ecological cylinder with compact switch Variations added 7

2 ew ecofriendly cylinder onventional switch ompact switch ew easytouse S Series (ø to ø) air cylinders Remove toxic substances and protect the environment by preventing contamination ort and needle on same plane ir supply/exhaust port and cushion needle installation on same side. ylinder installation/adjustment, etc., were easily. switch smaller than the conventional switch is used. his eliminates switch protrusion in installation, saving space. ew switch Switches are installed easily and smoothly with our original switch bracket. () Easily install switches. he mechanism sandwiches the tie rod, making the switch position adjustable without supporting the switch. switch owerful fixing () Fix with screws alone. Installation is completed by tightening screws after adjusting switches. type switch in the rail can be finely adjusted. Ecological product Harmful substances such as lead and hexavalent chrome that adversely affect the global environment are not used in the cylinder and cylinder switch. (Lead free soldered lead wire is used) Standard magnets Switches can be installed on all products. S Series roducts Standard type S Spacesaving Less installation space is required because the cylinder is up to mm shorter than the conventional cylinder. White roducts match a variety of equipment with a uniform white exterior. Model variation Stroke length (mm) to 0 age osition locking type SQ 7 Same dimensions for rubber scraper type (), coolant proof type (, ), spatter adherence prevention type () he dimensions of the rubber scraper type, coolant proof type, spatter adherence prevention type have been made the same as the standard type to improve installation performance. Lowspeed type Lowfriction type Doublerod type onrotating type S0 SU SD SM Directivecompatible Rubber scraper type oolant proof type S S, 7 Spatter adherence prevention type S 7

3 Safety recautions lways read before starting use When designing and manufacturing a device using D products, the manufacturer is obligated to check that device safety mechanical mechanism, pneumatic control circuit, or water control circuit and the system operated by electrical control that controls the devices is secured. It is important to select, use, handle, and maintain the product appropriately to ensure that the D product is used safely. Observe warnings and precautions to ensure device safety. heck that device safety is ensured, and manufacture a safe device. WRI his product is designed and manufactured as a general industrial machine part. It must be handled by an operator having sufficient knowledge and experience in handling. Use this product in accordance of specifications. ontact D when using the product outside the unique specifications range, when using it outdoors, and when using it under the conditions and environment below.do not attempt to modify or additionally machine the product. Use for special applications requiring safety including nuclear energy, railroad, aviation, ship, vehicle, medical equipment, equipment, or applications coming into contact with beverage or food, amusement equipment, emergency shutoff circuits, press machine, brake circuits, or for safeguard. Use for applications where life or assets could be adversely affected, and special safety measures are required. Observe corporate standards and regulations, etc., related to the safety of device design and control, etc. ISO, JIS B 0 (pneumatic system rules), JS 00 (principles for pneumatic cylinder use and selection), High ressure as Maintenance Laws Occupational Safety and Sanitation Laws, and other safety regulations, corporate standards, and regulations. Do not handle, pipe, or remove devices before confirming safety. Inspect and service the machine and devices after confirming safety of the entire system related to this product. ote that there may be hot or charged sections even after operation is stopped. When inspecting or servicing the device, turn off the energy source (air supply or water supply), and turn off power to the facility. Discharge any compressed air from the system, and pay enough attention to possible water leakage and leakage of electricity. When starting or restarting a machine or device that incorporates pneumatic components, make sure that the system safety, such as popout prevention measures, is secured. Observe warnings and cautions on the pages below to prevent accidents. he safety cautions are ranked as "DER", "WRI" and "UIO" in this section. DER: WRI: UIO: When a dangerous situation may occur if handling is mistaken leading to fatal or serious injuries, or when there is a high degree of emergency to a warning. When a dangerous situation may occur if handling is mistaken leading to fatal or serious injuries. When a dangerous situation may occur if handling is mistaken leading to minor injuries or physical damage. ote that some items described as "UIO" may lead to serious results depending on the situation. In any case, important information that must be observed is explained. Intro

4 neumatic components Safety recautions lways read before starting use Refer to neumatic ylinders o. B0S for general details on cylinders and cylinder switch. ierod cylinder S series Design & Selection. ommon UIO Install a flow control valve on the cylinder. Install a flow control valve on the cylinder. Use within the working piston speed of each series. UIO Either the rubber cushion type or air cushion type cushion mechanism is assembled in the cylinder. he purpose of the air cushion is to absorb kinetic energy that the piston has by using air compression, and prevent the piston and cover from colliding at the stroke end. hus, the cushion is not used to decelerate the piston near the stroke end. he table below shows kinetic energy that can be absorbed by the cushion. If kinetic energy exceeds these values, or if bouncing caused by air compression is to be avoided, consider using another cushioning unit.. osition locking type SQ UIO eep the cylinder load rate at % or less.if the load rate is high, the lock may not be released and the lock section could be damaged.. Lowfriction type SU WRI Durability differs based on the work conditions and model features. his cylinder has internal leakage.refer to the specifications (page ) for details on the leakage amount. UIO When using with a balancer, etc., it may be better not to install a speed controller to improve the supply and exhaust efficiency. Use of circuits (a) to (c) below is recommended depending on the application. (a) ension control (winder, etc.) (b)balancer (EDM Z axis, etc.) (mm) Rubber cushion llowable energy absorption J Effective cushion length (mm)..... ir cushion llowable energy absorption J roportional control valve (c)load control (polishing, etc.) roportional control valve Highrelief regulator... inetic energy (J) = / x weight (kg) x {speed (m/s)} (ote) alculating kinetic energy: he cylinder average speed is obtained with Va = L/. Va : verage speed (m/s) L : ylinder stroke (m) : Operation time (s) ylinder speed just before entering the cushion can be obtained with the following simple expression: Vm=L/ X (+. X /) Vm: Speed just before entering cushion (m/s) : ylinder load rate (%) When calculating kinetic energy, use Vm value as speed. Highrelief regulator (for jig selfweight cancellation) * Increase the piping volume as much as possible to improve the supply and exhaust features. Do not lubricate this product or features will be adversely affected. oor air quality worsens features and adversely affects durability. lways Use clean air with the following piping. Dryer ir filter ( m) Oil mist filter (removal of oil) Intro

5 S Series Install the speed controller near the cylinder. djustment may be unstable if assembled at a place away from the cylinder. enerally, the Speed is stable when the air pressure is higher and the load rate is lower. eep the load rate at % or lower.. oolant proof type S/ UIO Do not apply a deviated load onto the piston rod. Scraper or bearing life could be shortened. When using the or series and the coolant or water does not splatter, the piston rod's lubrication could be spent and cause the life to shorten.use the Series in this case.. Spatter adherence prevention type S WRI he durability of this cylinder in an environment containing spatter is higher than the general cylinder, but durability may be shorter than the general cylinder when used in other environments. Intro

6 S Series Installation & djustment. ommon UIO recautions for installing the switch ssembling the switch bracket When assembling the cylinder on the switch bracket, fit the tierod to be installed into the bracket, and move the switch so that it is at the center of the operation range (O range). hen, tighten the fixing bolts with a tightening torque of 0. to 0. m. he bracket position (, D) and switch positions (RD, HD) at which the maximum sensitivity is attained at both stroke ends are shown in the outline drawing. Rod cover Head cover RD/HD /D Marking color indicator switch Rod cover Head cover /D color indicator switch Moving the switch position in the stroke direction s a default, the switch is set to the maximum sensitivity. However, the color indicator switch can be finely adjusted approx. mm from the default installation position. If the adjustment range exceeds mm, or when adjusting the color indicator switch, loosen the switch bracket's fixing screw and move the bracket position. Fixing the switch When using the,, 0, or switch, use a flattip screwdriver with to mm grip,. mm or smaller tip width, and 0. mm or thinner (clock screwdriver, precision screwdriver, etc.), and tighten with a tightening torque of 0. to 0. m. When using *, J, Y, Y, YF, YF, YM, or YM, tighten with a tightening torque 0. to 0.7 m. he switch bracket rail has a mark mm from the rail end. Use this as a guide to the installation position when replacing the switch. Switch rail markings are set to default switch maximum sensitivity. Maximum sensitivity is changed when the switch is changed or when the switch bracket is moved. djust the position accordingly. Supply pressure exceeding minimum working pressure to ports having locks. If piping on the side with the lock is thin and long, or if the speed controller is separated from the cylinder port, exhaust may slow, taking time for the lock to function. his may also occur if the silencer on the valve's EXH. port is clogged.. Lowfriction SU UIO Do not apply a horizontal load to the cylinder. Install the cylinder so that the sliding guide is not twisted. Operation could become unstable because of fluctuations in load and resistance. When using a long stroke, the speed becomes unstable because of the piston rod s weight. Install a guide when using the long stroke. Operation of a guide having a large difference in stationary friction and moving friction could become unstable. void using where there is vibration. he product could be adversely affected by vibration, and result in unstable operation.. onrotating type SM UIO heck that the rotation torque is not applied to the piston rod. he nonrotating bushing could deform and life could drop remarkably. pply the load to the piston rod so that it is in the piston rod's axial direction. When fixing a workpiece to the end of the piston rod, pull the piston rod into the stroke end. hen, attach a wrench to the section protruding outside the parallel section of the rod, and tighten while making sure that the tightening torque is not applied to the cylinder.. osition locking type SQ UIO he lock functions at the stroke end. If the stopper is applied with an external stopper in the middle of the stroke, the lock may not function and result in dropping. onfirm that the lock functions before setting the load. When using the baffle cylinder and fixing a workpiece to the end of the piston rod, the rotation torque applied to the piston rod is as shown below. pplying a higher rotation torque to the piston rod could cause the operation of piston rod to fail. llowable rotation torque m Intro

7 S Series During use & Maintenance. osition locking type SQ WRI For safety purposes, prevent the load from dropping under its own weight during maintenance. If pressure is applied from port () in the locked state and with neither port pressurized, it may not be possible to release locks, or the lock may be released suddenly and cause the piston rod to pop out. his is extremely hazardous. When releasing the locking mechanism, supply pressure to port (B), and check that there is no load applied to the locking mechanism. ort W When stopping with an external shock absorber, etc., adjust in the same manner so that there is no bouncing. Regularly (once/twice a year) check that the holding section is not damaged this way. UIO If negative pressure is applied to the locking mechanism, the lock may be released. Use the solenoid valve as a discrete unit, or use an independently exhausted manifold. If the locking mechanism has been manually operated, check and then return it manually to the original position.do not use manual operations other than during adjustment, as this is very hazardous. ort Side without locking mechanism B W ort ort B Side without locking mechanism Release the lock when installing or adjusting the cylinder. he lock could be damaged if the cylinder is installed while the lock is applied. If lowering speed is to be increased with the quick exhaust valve, the cylinder may move out faster than the lock pin and prevent the locking pin from being released correctly. Do not use a position valve. Do not use a position valve. Do not use this cylinder with a position (especially closed center metal seal) valve.he lock will not be applied if pressure is sealed on the port having the locking mechanism.even if the lock is applied, the air that leaks from the solenoid valve may enter the cylinder, or the lock may be released over time. When using the cylinder with air cushion, if the air cushion needle on the lock mechanism side is tightened too tight, the piston could bounce at the stroke end causing the sleeve and stopper piston to collide and damage the locking mechanism. If the air cushion needle is opened too far, the piston could spring back at the stroke end and cause similar damage. djust the air cushion needle so that the piston does not bounce. Bouncing phenomenon Stopper piston Holder to contact Sleeve Do not use multiple cylinders. Do not move one workpiece using two or more position locking cylinders.it may not be possible to release one of the cylinder's locks. Use the speed controller with meterout control. It may not be possible to release the locks when used with meterin control. Use the side with the lock with the cylinder stroke end. If the cylinder's piston does not reach the stroke end, the lock may not be applied or may not be released. Releasing the locking type manual override Screw a release bolt into the stopper piston, and pull the bolt up the movement amount with a force of and over. he stopper piston moves and the lock is released. (During noload horizontal installation or counter side port is pressurized).when the hand is released, if the stopper piston returns by the internal spring and enters the piston rod groove, the piston is locked. Release bolt Stopper spring Stopper piston iston rod slot Movement Lock Lock release (mm) Lock Lock Release Movement release bolt M X M X M X M X M X M X Intro

8 S Series Releasing the nonlocking type manual override When the round nut is turned counterclockwise, the stopper piston moves and the lock is released. When the nut is turned clockwise to the lock position, the stopper piston returns. When it fits into the piston rod groove again, the piston is locked. Round nut Movement (mm) Lock Lock release Movement Lock Lock release..... Lowspeed SO WRI he O Series uses fluorinebased grease. Lighting a cigarette with fluorinebased grease on hands generates toxic gases.. Lowfriction SU UIO Do not disassemble this product. It may not be possible to maintain performance if disassembled. he repair parts of this product cannot be purchased without this products purchased. Intro

9 Variation ie rod cylinder S series S Series Variation : Standard, : Option, : ustom order, : ot available Mounting style ushion Option ccessory Variation Model o. JIS symbol (mm) Stroke length (mm) Max. stroke length(mm) Basic type xial foot type Rod side flange type Head side flange type Eye bracket type levis bracket type Rod side trunnion type Head side trunnion type enter trunnion type o cushion ir cushion on both sides Rubber cushion on both sides Bellows (0 ) iston rod material, stainless steel opper and FE free Rod eye Rod clevis Eye bracket levis bracket Eye bracket runnion type o. bracket Switch age LB F FB B B B D J M I Y B B B B Double acting single rod type Double acting position locking type Double acting lowspeed type Double acting lowfriction type Double acting doublerod type Double acting nonrotating type S SQ SO SU SD SM to to to to to to ontact D. ontact D. 7 Double acting rubber scraper type Doubleacting, coolant proof type Double acting spatter adherence prevention type S S, S to to to ontact D. 7 7

10 ie rod cylinder Double acting single rod type S series :,,,,, JIS symbol Specifications Descriptions S mm ctuation Working fluid Max. working pressure Ma Min. working pressure Ma Withstanding pressure Ma mbient temperature ort size Stroke tolerance Rubber cushioned mm ir cushioned Working piston speed mm/s ushion Effective air cushion length mm Lubrication llowable energy Rubber cushioned absorption J ir cushioned +. 0 Rc/ (to 0) Double acting ompressed air to 0 (to be unfrozen) Rc/ Rc/ (to 0) 0 (to 0), 0 ( to 0) (to 0), 0 (to 0), 0 ( to 0) to 0 (use it within the range of allowable energy absorption) Rubber cushion/air cushion can be selected.. ot required (When lubricating, use turbine oil lass ISO V)..... Rc/... Stroke length Standard stroke length (mm),, 7,,, 0,, 0,, 0,, 0 Max. stroke length (mm) vailable stroke length (mm) Min. stroke length (mm) ote : ustom stroke length is available per mm increment. ote : If the maximum stroke is exceeded, product specifications many not be met depending on operating conditions. onsult with D in this case. Min. stroke length of type with switch When installed on different planes Switch quantity When installed on the same plate Switch quantity (Unit: mm) (Unit: mm) 0

11 Min. stroke length of type with switch runnion type (, B) Switch quantity 0 (Unit: mm) S Series Specifications runnion type () Switch quantity (Unit: mm) Switch specifications One color/bicolor indicator/strong magnetic field proof Descriptions pplications ower voltage Load voltage Load current Light wire wire wire wire H/V/JH/JV YH/YV H/V YH/YV 0H/0V H/V YD controller controller, relay controller, relay controller, relay, I circuit (without indicator light), serial connection controller 0 to V D 0 to V D V D or less /V D 0V V //V D 0V V V D 0% to m (ote ) m or less m or less to m 7 to m 7 to 0 m m or less m or less 0 m or less to m LED Red/green LED LED Red/green LED LED Red/green LED (O lighting) (O lighting) (O lighting) (O lighting) (O lighting) (O lighting) ote : he maximum load current of m applies at.if the switch's ambient operating temperature exceeds, the load current becomes less than m.( to 0 m when 0.) With preventive maintenance output Descriptions pplications Installation position adjustment Red/green LED (O lighting) wire wire wire wire YFH/V controller YFH/V controller, relay YMH/V controller YMH/V controller, relay reventive maintenance output Yellow LED (O lighting) ower voltage Load voltage Load current Load voltage 0 to V D to m 0 to V D V D or less m or less VD or less 0 to V D to m 0 to V D V D or less m or less Load current m or less m or less to m or less m or less Light Output reventive maintenance output ote : he maximum load current of m applies at.if the switch's ambient operating temperature exceeds, the load current becomes less than m.( to 0 m when 0.) Weight (mm) Unit: kg roduct weight when stroke length =0 mm Stroke length: Switch weight ccessory weight Basic type Foot type Flange type Eye bracket type levis bracket type runnion type dditional weight (00) (LB) (F, FB) () (B) (, B, ) per mm rommet I Y

12 S Series How to order Without switch S LB B With switch S Model o. LB B H R J Mounting style ote B ote on model o. selection ote : he installation bracket is shipped with the product. (ote that trunnion type, rod side flange with bellows is assembled to ship.) ote : ustom stroke length is available per mm increment. ote : he instantaneous maximum temperature is that at which sparks, swarf, etc., temporarily contact bellows. ote : "I" and "Y" cannot be selected at the same time. <Example of model number> SLBBHDJI ort thread type D ushion E Stroke length ote Model: ierod cylinder, double acting single rod type Mounting style : xial foot type B : mm ort thread type : Rc thread D ushion : Both sides aircushioned E Stroke length : mm F Switch model o. : H switch, lead wire m Switch quantity : wo H Option : With bellows I ccessory : Rod eye (attachment) J F Switch model o. I I Switch quantity H Option ote I ccessory ote Descriptions Mounting style 00 Basic type LB xial foot type F Rod side flange type FB Head side flange type Eye bracket type B levis bracket type Rod side trunnion type B Head side trunnion type enter trunnion type B D ushion B ir cushion on both sides (basic type) D Rubber cushion on both sides ote: he rubber cushion is longer than the air cushion. E Stroke length (mm),, 7,,, 0,, 0,, 0,, 0 Switch model o. F xial lead wire 0H* H* H* H* YH* YH* YFH* YFH* YMH* YMH* YD* YD* ort thread type Blank Rc thread thread (custom order) thread (custom order) Radial lead wire 0V* V* V* V* YV* YV* YFV* YFV* YMV* YMV* JH* JV* *Lead wire length Blank m (standard) m (option) m (option) Switch quantity R H D H One on rod side One on head side wo hree ontact Indicator Lead wire color indicator Without indicator light color indicator color indicator color indicator (Without light for preventive maintenance output) color indicator (With light for preventive maintenance output ( color)) Strong magnetic field proof switch Offdelay type Option Max. ambient temperature J Bellows 0 M iston rod material (stainless steel) opper and FE free I ccessory I Y B B B B wire wire wire wire wire wire wire wire wire wire wire Instantaneous ambient temperature Rod eye Rod clevis (connector pin and split pin attached) Eye bracket levis bracket (connector pin and split pin attached) Eye bracket runnion type o. bracket

13 S Series How to order How to order switch Switch body + mounting bracket Switch body Switch bracket set S 0H SW 0H S Switch model o. ( F on previous page) ( B on previous page) Switch model o. ( F on previous page) Bracket ( B on previous page) ote: If a type switch of ecological is used, please consult with D. How to order mounting bracket Mounting bracket Foot (LB) Flange (F) (FB) ote Eye () levis (B) SLB SF S SB SLB SF S SB SLB SF S SB SLB SF S SB SLB SF S SB SLB SF S SB ote : Designate "SF(bore size)j" for the flange with bellows (F). ote : he foot (LB) is provided as a twopiece set.

14 S Series Internal structure and parts list S Rubber cushioned o. arts name Material Remarks o. arts name Material Remarks Rod nut ickeling Magnet lastic iston rod Industrial chrome plated Wear ring cetar resin Rod packing seal itrile rubber iston H, : aluminum alloy Bush Oil impregnated bearing alloy to : aluminum alloy die casting Rod cover luminum alloy die casting aint ushion needle Brass ylinder gasket itrile rubber eedle gasket itrile rubber 7 ushion packing seal itrile rubber, steel Only with air cushion 7 Head cover luminum alloy die casting aint ylinder tube luminum alloy Hard alumite ierod Zinc chromate plating iston R, : aluminum alloy Round nut Zinc chromate plating to : aluminum alloy die casting Hexagon socket head cap screw Zinc chromate plating 0 iston packing seal itrile rubber Bracket Stainless steel spring steel iston gasket itrile rubber Switch ushion rubber Urethane rubber Only with rubber cushion Repair parts list ir cushioned Rubber cushioned it number Repair parts number it number Repair parts number SB SD SB SD SB 7 SD 0 SB SB 0 SD SD SB SD ote: Specify the kit number when placing an order. ote: Specify the kit number when placing an order. Mounting bracket material Mounting style Material LB F/FB /B ast iron /B/ ast iron Remarks ickeling aint aint aint 7

15 S Series Double acting single rod type Dimensions Basic type (00) M MO (Width across flats) X + stroke length LL + stroke length M F V RD HD EE (port) ushion needle Q D Q SD J e Width across flats B J e MM SD D DB D D D DB 0 X + + stroke length + b d <With bellows > ote : Dimensions in parentheses are for the rubber cushion, which is longer than the air cushion. ( / ; + mm, / ; + mm, / ; +0 mm) ote : RD and HD in the dimensions indicate the switch end positions, and and D indicate the switch rail end positions. Basic type (00) basic dimensions B D DB D EE F J ote LL M MM M MO O Q 7. M Rc/. M0 X. (0). 0 M Rc/ M X. (0) M Rc/ 0.. M X. (0) 7. M Rc/. 7 M X. (0) 7 7. M0 Rc/ M X. (). M0 Rc/ M X. () 7 SD V ote X With bellows b d or less to to to 0 0 to 0 0 to 0 0 to 0 0 to to to 0. (). (). () 7. () (0) (0) With switch ote D ote RD ote HD ote () () () () () () () (). (.) (). (0.) (). (.) (). (0.) (). (.) (7). (7.) () (). (7.) (7). (.) ote : Refer to age 7 for HD, RD dimensions and dimensions of projecting section of color indicator type, preventive maintenance output switch.

16 S Series Dimensions xial foot type (LB) EE (port) M O F ushion needle V Q L + stroke length LL + stroke length RD HD D Q LH Width across flats B MM LD LB L L + stroke length L LB b + d L LR LS L + + stroke length ote : Dimensions in parentheses are for the rubber cushion, which is longer than the air cushion. ( / ; + mm, / ; + mm, / ; +0 mm) ote : RD and HD in the dimensions indicate the switch end positions, and and D indicate the switch rail end positions. xial foot type (LB) basic dimensions B EE F ote LL M MM O Q 7. Rc/ Rc/ Rc/ Rc/ Rc/ Rc/ M0 X. M X. M X. M X. M X. M X. (0) (0) (0) (0) () () With bellows LB L LD ote LH LR LS L b d or to to to 0 to L less () () () () 7 () 7 () With switch ote D ote RD ote <With bellows > HD ote () (). (.). (.). (.) () () () () () (7). (7.) () (). (0.). (0.). (7.) (7) () () () () (). (.) ote : Refer to age 7 for HD, RD dimensions and dimensions of projecting section of color indicator type, preventive maintenance output switch. V 0 to to 0 Installation dimensions ote L () 70 (7) 0 () () () () 0 to to to 0 7 7

17 Je Dimensions S Series Double acting single rod type Rod side flange type (F) FM X + stroke length FL LL + stroke length EE (port) ushion needle V M Q RD HD D Q F + stroke length X + + stroke length + b M d FH F Width across flats B MM FJ FD FF O <With bellows > ote : Dimensions in parentheses are for the rubber cushion, which is longer than the air cushion. ( / ; + mm, / ; + mm, / ; +0 mm) ote : RD and HD in the dimensions indicate the switch end positions, and and D indicate the switch rail end positions. Rod side flange type (F) basic dimensions B EE F J ote LL M MM O Q V 7. Rc/ Rc/ Rc/ Rc/ Rc/ Rc/ M0 X. M X. M X. M X. M X. M X. (0) (0) (0) (0) () () Installation dimensions With bellows F FD FF ote F FJ M FH FL FM b d or to to to 0 to 0 to 0 to 0 to less (0) (0) 0 () 0 () () () With switch ote () (). (.). (.). (.) () D ote () () () () (7). (7.) RD ote () (). (0.). (0.). (7.) (7) HD ote () () () () (). (.) ote : Refer to age 7 for HD, RD dimensions and dimensions of projecting section of color indicator type, preventive maintenance output switch. ote X () () () () 0 (0) 0 (0) 00 to to

18 S Series Dimensions Head side flange type (FB) F + stroke length V Q LL + stroke length RD HD D Q F FM FL ushion needle EE (port) F FH Width across flats B MM J e FJ + stroke length O FD F + + stroke length + b d <With bellows > ote : Dimensions in parentheses are for the rubber cushion, which is longer than the air cushion. ( / ; + mm, / ; + mm, / ; +0 mm) ote : RD and HD in the dimensions indicate the switch end positions, and and D indicate the switch rail end positions. Head side flange type (FB) basic dimensions B EE F J ote LL M MM O Q V 7. Rc/. M0 X. (0) Rc/ M X. (0) Rc/ 0.. M X. (0). Rc/. 7 M X. (0) 7. Rc/ M X. (). Rc/ M X. () 7 Installation dimensions ote F F FD ote FJ FL FM F With bellows b d or less to to to 0 0 to 0 0 to 0 0 to 0 0 to to to 0 (7) 7 () 7 0. () () (7) (7) (7) (7) 7 () (7) () 7 (7) With switch ote D ote RD ote HD ote () (). (.). (.). (.) () () () () () (7). (7.) () (). (0.). (0.). (7.) (7) () () () () (). (.) ote : Refer to age 7 for HD, RD dimensions and dimensions of projecting section of color indicator type, preventive maintenance output switch.

19 Dimensions S Series Double acting single rod type Eye bracket type () V Q + stroke length LL + stroke length RD HD D Q F l ushion needle Q EE (port) R E Width across flats B MM J e D J + stroke length + +stroke length b + d H0 O <With bellows > ote : Dimensions in parentheses are for the rubber cushion, which is longer than the air cushion. ( / ; + mm, / ; + mm, / ; +0 mm) ote : RD and HD in the dimensions indicate the switch end positions, and and D indicate the switch rail end positions. Eye bracket type () basic dimensions B EE F J ote LL M O Q V 7. Rc/ Rc/ Rc/ Rc/ Rc/ Rc/ M0 X. M X. M X. M X. M X. M X. (0) (0) (0) (0) () () Installation dimensions With bellows ote ote D E F I Q b d or to to to 0 to J less 0 0. (70.) (7) 7 () 7 () () () () () 7 () 7 () () () With switch ote () (). (.). (.). (.) () D ote () () () () (7). (7.) RD ote () (). (0.). (0.). (7.) (7) HD ote () () () () (). (.) ote : Refer to age 7 for HD, RD dimensions and dimensions of projecting section of color indicator type, preventive maintenance output switch. 0 to to 0 0 to to to 0 7 7

20 S Series Dimensions levis bracket type (B) V Q + stroke length LL + stroke length RD HD D Q F l ushion needle V W EE (port) R E D Width across flats B J e J + stroke length d MM H0 O + +stroke length + b <With bellows > ote : Dimensions in parentheses are for the rubber cushion, which is longer than the air cushion. ( / ; + mm, / ; + mm, / ; +0 mm) ote : he pin, split pin, and plain washer are included. ote : RD and HD in the dimensions indicate the switch end positions, and and D indicate the switch rail end positions. levis bracket type (B) basic dimensions B EE F J M MM O Q E 0. 7 F With switch. I 7 7 ote Rc/ Rc/ Rc/ Rc/ Rc/ Rc/ ote J () () 7 () 7 () () (). 0. V 0 0 D ote.. W 7 M0 X. M X. M X. M X. M X. M X. With bellows b.. RD ote HD ote ote LL (0) (0) (0) (0) () () () (). (.). (.). (.) () () () () () (7). (7.) () (). (0.). (0.). (7.) (7) () () () () (). (.) ote : Refer to age 7 for HD, RD dimensions and dimensions of projecting section of color indicator type, preventive maintenance output switch. d 7 7 or less to. 7 to to to to to 0 V 0 to to 700 Installation dimensions ote D. (70.) 0 (7) 0 7 () 7 () () () 700 to 0 7 7

21 Je Dimensions S Series Double acting single rod type Rod side trunnion type () X + stroke length LL + stroke length M F V HD EE (port) ushion needle Q D Q D e Width across flats B MM J e O E M F + stroke length b X + + stroke length + d <With bellows > ote : Dimensions in parentheses are for the rubber cushion, which is longer than the air cushion. ( / ; + mm, / ; + mm, / ; +0 mm) ote : Switches cannot be installed on the head side. ote : HD in the dimensions indicates the switch end positions, and D indicates the switch rail end positions. Rod side trunnion type () basic dimensions B EE F J ote LL M MM O Q V 7. Rc/. M0 X. (0) Rc/ M X. (0) Rc/ 0.. M X. (0). Rc/. 7 M X. (0) 7. Rc/ M X. (). Rc/ M X. () 7 Installation dimensions With switch ote ote ote ote D E F M X D HD () (7.) 7 () () () 7 0 () () () () 7.. (.) 7 07 () () ().. (.) 0 () () 0 (0) (7) 0 (7) () 0 (0) (). (7.). (.) With bellows With bellows b d or less to to to to 0 0 to to 0 0 to to to ote : Refer to age 7 for HD, RD dimensions and dimensions of projecting section of color indicator type, preventive maintenance output switch.

22 S Series Dimensions Head side trunnion type (B) X + stroke length LL + stroke length M F V RD EE (port) ushion needle Q Q D e J e Width across flats B MM J e O E M J + stroke length X + + stroke length + b d ote : Dimensions in parentheses are for the rubber cushion, which is longer than the air cushion. ( / ; + mm, / ; + mm, / ; +0 mm) ote : Switches cannot be installed on the head side. ote : RD in the dimensions indicates the switch end positions, and indicates the switch rail end positions. Head side trunnion type (B) basic dimensions B EE 7. Rc/ Rc/ Rc/ Rc/ Rc/ Rc/ Installation dimensions ote ote D E X J M () (7.). () 7 (7) () 7 7. (.) 7. 7 () 70. (7.). 0 0 (0) 0 () (0) 7 (7) F J <With bellows > M0 X. M X. M X. M X. M X. M X ote () (). (.). (.). (.) () ote LL (0) (0) (0) (0) () () With switch M. 7 ote RD () (). (0.). (0.). (7.) (7) MM O Q 7.. With bellows b.. d 7 7 V or less With bellows ote : Refer to age 7 for HD, RD dimensions and dimensions of projecting section of color indicator type, preventive maintenance output switch. to 0 0 to 0 0 to 0 0 to 0 0 to to to to to

23 Je Dimensions S Series Double acting single rod type enter trunnion type () EE (port) M F ushion needle V Q X + stroke length LL + stroke length RD HD D Q J e E stroke length Y + Z + stroke length b + d D e Width across flats B MM O M ( ) <With bellows > ote : Dimensions in parentheses are for the rubber cushion, which is longer than the air cushion. ( / ; + mm, / ; + mm, / ; +0 mm) ote : RD and HD in the dimensions indicate the switch end positions, and and D indicate the switch rail end positions. enter trunnion type () basic dimensions B 7 ote X () () () () 0 (0) 0 (0) 0 to to EE Rc/ Rc/ Rc/ Rc/ Rc/ Rc/ D E 7 F. 0. Installation dimensions 700 to 0 With switch M ote J 7 ote Y 7 (70) () 70 (7) 70 (7) () () D ote M0 X. M X. M X. M X. M X. M X. ote Z () () () () () () ote LL M (0) (0) (0) (0) (). () 7 With bellows RD ote b.. d 7 7 HD ote MM or less () (). (.). (.). (.) () () () () () (7). (7.) () (). (0.). (0.). (7.) (7) () () () () (). (.) ote : Refer to age 7 for HD, RD dimensions and dimensions of projecting section of color indicator type, preventive maintenance output switch. O 7 to Q.. to to V 0 to 0 0 to to 0

24 ie rod cylinder Double acting, position locking type SQ Series :,,,,, JIS symbol Specifications Descriptions mm ctuation Working fluid Max. working pressure Ma Min. working pressure Ma Withstanding pressure Ma mbient temperature ort size Stroke tolerance mm Working piston speed mm/s ushion Valid air cushion length mm osition locking mechanism Holding force Lubrication llowable energy absorption J ir cushioned Rc/ SQ Double acting ompressed air to 0 (to be unfrozen) Rc/ Rc/ (to 0), 0 (to 0), 0 ( to 0) to 0 (use it within the range of allowable energy absorption) ir cushion. Head side, rod side Max. thrust X 0.7 ot required (when lubricating, use turbine oil lass ISO V.)... Rc/.. Stroke length Standard stroke (mm),, 7,,, 0,, 0,, 0,, 0 Max. stroke length (mm) vailable stroke length (mm) Min. stroke length (mm) ote : ustom stroke length is available per mm increment. ote : If the maximum stroke is exceeded, product specifications many not be met depending on operating conditions. onsult with D in this case. Min. stroke length of type with switch When installed on different planes Switch quantity When installed on the same plate Switch quantity (Unit: mm) (Unit: mm) 0 7

25 Min. stroke length of type with switch runnion type (, B) Switch quantity 0 (Unit: mm) SQ Series Specifications runnion type () Switch quantity (Unit: mm) Switch specifications One color/bicolor indicator/strong magnetic field proof Descriptions pplications ower voltage Load voltage Load current Light ote : he maximum load current of m applies at.if the switch's ambient operating temperature exceeds, the load current becomes less than m.( to 0 m when 0.) With preventive maintenance output Descriptions pplications Installation position adjustment Red/green LED (O lighting) wire wire controller, relay wire wire YFH/V controller YFH/V ontroller and relay YMH/V controller YMH/V controller, relay reventive maintenance output Yellow LED (O lighting) ower voltage Load voltage Load current Load voltage 0 to V D to m 0 to V D V D or less m or less V D or less 0 to V D to m 0 to V D V D or less m or less Load current m or less m or less to m (ote ) m or less Light Output reventive maintenance output wire wire wire wire H/V/JH/JV YH/YV H/V YH/YV 0H/0V H/V YD controller controller controller, relay controller, relay, I circuit (without indicator light), serial connection controller 0 to V D 0 to V D V D or less /V D 0V V //V D 0V V V D 0% to m (ote ) m or less m or less to m 7 to m 7 to 0 m m or less m or less 0 m or less to m LED Red/green LED LED Red/green LED LED Red/green LED (O lighting) (O lighting) (O lighting) (O lighting) (O lighting) (O lighting) ote : he maximum load current of m applies at.if the switch's ambient operating temperature exceeds, the load current becomes less than m.( to 0 m when 0.) Weight (mm) Unit: kg roduct weight when stroke length =0 mm Stroke length: Switch weight ccessory weight Basic type Foot type Flange type Eye bracket type levis bracket type runnion type mm dditional weight (00) (LB) (F, FB) () (B) (, B, ) per mm rommet I Y

26 SQ Series How to order Without switch SQ LB B H With switch SQ Model o. Mounting style ote ote on model o. selection <Example of model number> SQLBBHHDI Model: ierod cylinder, double acting position locking type B D E F H I J M I LB B H H R M I B ort thread type D ushion E Stroke length ote ote : he installation bracket is shipped with the product. (ote that the trunnion type is assembled before shipment.) he mounting style and position locking mechanism R are not used. he mounting style B and position locking mechanism H are not used. ote : ustom stroke length is available per mm increment. ote : he instantaneous maximum temperature is that at which sparks, swarf, etc., temporarily contact bellows. ote : "I" and "Y" cannot be selected at the same time. F osition locking mechanism Switch model o. H Switch quantity I Option ote Mounting style : xial foot type : mm ort thread type : Rc thread ushion : Both sides aircushioned Stroke length : mm J ccessory osition locking mechanism : With head side position locking ote Switch model o. : H switch, lead wire m Switch quantity : wo Option : Basic position locking type ccessory : Rod eye (attachment) Descriptions Mounting style 00 Basic type LB xial foot type F Rod side flange type FB Head side flange type Eye bracket type B levis bracket type Rod side trunnion type B Head side trunnion type enter trunnion type B ort thread type Blank Rc thread thread (custom order) thread (custom order) D ushion B ir cushion on both sides (basic type) E Stroke length (mm),, 7,,, 0,, 0,, 0,, 0 F osition locking mechanism H With head side position locking R With rod side position locking Switch model o. xial lead wire 0H* H* H* H* YH* YH* YFH* YFH* YMH* YMH* YD* YD* Radial lead wire 0V* V* V* V* YV* YV* YFV* YFV* YMV* YMV* JH* JV* *Lead wire length Blank m (standard) m (option) m (option) H Switch quantity R One on rod side H One on head side D wo hree Option I Blank MO M M J ccessory I Y B B B B ontact Indicator Lead wire color indicator Without indicator light color indicator color indicator color indicator (Without light for preventive maintenance output) color indicator (With light for preventive maintenance output ( color)) wire wire wire wire wire wire wire wire wire Strong magnetic field proof switch wire Offdelay type wire Basic position locking type onlocking manual override (release bolt attached) Locking manual override iston rod material (stainless steel) opper and FE free Rod eye Rod clevis (pin and split pins attached) Eye bracket levis bracket (pin and split pins attached) Eye bracket runnion type o. bracket

27 SQ Series How to order How to order switch Switch body + mounting bracket Switch body Switch mounting bracket S 0H SW 0H S Switch model o. ( on previous page) ( B on previous page) Switch model o. ( on previous page) Bracket ( B on previous page) ote: If an ecological type switch is used, consult with D. How to order mounting bracket Mounting bracket Foot (LB) SLB SLB SLB SLB SLB SLB Flange (F) (FB) SF SF SF SF SF SF Eye () S S S S S S levis (B) SB SB SB SB SB SB ote : Foot (LB) is provided as pieces per set.

28 SQ Series Internal structure drawing With rod side position locking With head side position locking 7 0 7

29 SQ Series arts list arts list o. arts name Material Remarks o. arts name Material Remarks Rod nut ickeling 7 Head cover luminum alloy die casting ote aint iston rod Industrial chrome plated ierod Zinc chromate plating Rod packing seal itrile rubber Round nut Zinc chromate plating Bush Oil impregnated bearing alloy Hexagon socket head cap screw Zinc chromate plating Rod cover luminum alloy die casting ote aint Bracket Stainless steel spring steel ylinder gasket itrile rubber Switch 7 ushion packing seal itrile rubber, steel Stopper cover luminum alloy die casting aint ylinder tube luminum alloy Hard alumite Hexagon socket head cap screw Stainless steel iston R, : aluminum alloy ushion rubber B Urethane rubber to : aluminum alloy die casting Spring 0 iston packing seal itrile rubber Stopper piston,, : stainless steel iston gasket itrile rubber,, : steel Zinc chromate plating Magnet lastic iston packing seal B itrile rubber Wear ring cetar resin Sleeve to : stainless steel Industrial chrome plated iston H, : aluminum alloy, : steel to : aluminum alloy die casting O ring itrile rubber ushion needle Brass Housing luminum alloy eedle gasket itrile rubber ote : luminum alloy diecasting is used for the rod side position locking. ote : luminum alloy casting is used for the rod side position locking. Repair parts list it number SQB SQB SQB SQB SQB SQB Repair parts number ote: Specify the kit number when placing an order. Mounting bracket material Mounting style Material LB F/FB /B ast iron /B/ ast iron Remarks ickeling aint aint aint

30 Je SQ Series Dimensions Basic type (00) head side position locking M MO (Width across flats) V Q X + stroke length RD LL + stroke length HD D QB F ushion needle O M EE (port) Q SD QE Width across flats B MM J e D DB D D D DB SD QD Q QF View ote : RD and HD in the dimensions indicate the switch end positions, and and D indicate the switch rail end positions. Basic type (00) head side position locking basic dimension B D DB D 7. M M M M M0 M0 QB Q QD QE QF Q EE F Rc/. Rc/ Rc/ 0. Rc/ Rc/ Rc/ SD... 7 J LL M MM M MO M0 X. M X. M X. M X. M X. M X. With switch V X D RD HD ote : Refer to age 7 for HD, RD dimensions and dimensions of projecting section of color indicator type, preventive maintenance output switch. O 7 Q..

31 SQ Series Double acting position locking type Dimensions Basic type (00) rod side position locking QB RH D Q Je Q M EE (port) O F ushion needle V X + stroke length LL + stroke length RD QE SD Width across flats B MM J e QF View QD Q SD D DB D D D DB ote : RD and HD in the dimensions indicate the switch end positions, and and D indicate the switch rail end positions. Basic type (00) rod side position locking basic dimensions B D DB D EE F J LL M MM O Q 7. M Rc/. M0 X. M Rc/ M X. 7 M Rc/ 0... M X. 0. M Rc/.. 7 M X M0 Rc/ M X.. M0 Rc/ M X. 7 With switch QB Q QD QE QF Q SD V X D RD HD ote : Refer to age 7 for HD, RD dimensions and dimensions of projecting section of color indicator type, preventive maintenance output switch.

32 SQ Series Dimensions xial foot type (LB) head side position locking V Q RD L + stroke length LL + stroke length HD D QB F ushion needle O M Q QD EE (port) Q QE Width across flats B MM LH L LB L L + stroke length L LB LD LR LS QF View ote : RD and HD in the dimensions indicate the switch end positions, and and D indicate the switch rail end positions. xial foot type (LB) head side position locking basic dimensions B EE F LL M MM O Q 7. Rc/. M0 X. Rc/ M X. 7 Rc/ 0... M X. 0. Rc/.. 7 M X Rc/ M X.. Rc/ M X. 7 Installation dimensions With switch Q V L LB L LD L LH LR LS L D RD HD QB.. Q QD ote : Refer to age 7 for HD, RD dimensions and dimensions of projecting section of color indicator type, preventive maintenance output switch. QE QF

33 Dimensions SQ Series Double acting position locking type xial foot type (LB) rod side position locking Q Q QD EE (port) M O F ushion needle V QB L + stroke length LL + stroke length RD HD D Q QE L LH Width across flats B MM QF View LR LS LD LB L L + stroke length L LB ote : RD and HD in the dimensions indicate the switch end positions, and and D indicate the switch rail end positions. xial foot type (LB) rod side position locking basic dimensions Q B EE F LL M MM O Q 7. Rc/ Rc/ Rc/ Rc/ Rc/ Rc/ M0 X. M X. M X. M X. M X. M X Installation dimensions With switch V L 70 LB L LD 7 L 0 0 LH LR LS L D RD HD QB Q ote : Refer to age 7 for HD, RD dimensions and dimensions of projecting section of color indicator type, preventive maintenance output switch. QD 7.. QE QF

34 SQ Series Dimensions Rod side flange type (F) head side position locking FM V M Q X + stroke length LL + stroke length RD HD D QB ushion needle FL O EE (port) Q J e FH F QE Width across flats B MM FF Fj F + stroke length FD QD Q QF View ote : RD and HD in the dimensions indicate the switch end positions, and and D indicate the switch rail end positions. Rod side flange type (F) head side position locking basic dimensions B EE F J LL M MM O Q QB Q QD QE 7. Rc/. M0 X. Rc/ M X. 7 7 Rc/ 0... M X Rc/.. 7 M X Rc/ M X.. 0 Rc/ M X. Installation dimensions 7 With switch QF Q V X F FD FF F Fj M FH FL FM D RD HD ote : Refer to age 7 for HD, RD dimensions and dimensions of projecting section of color indicator type, preventive maintenance output switch.

35 Dimensions SQ Series Double acting position locking type Rod side flange type (F) rod side position locking Q FM FL O EE (port) ushion needle V M QB X + stroke length LL + stroke length RD HD D Q QE F FH Width across flats B MM Fj J e QF View QD FD FF F + stroke length Q ote : RD and HD in the dimensions indicate the switch end positions, and and D indicate the switch rail end positions. Rod side flange type (F) rod side position locking basic dimensions QF B EE F J LL M MM O Q QB 7. Rc/ Rc/ Rc/ Rc/ Rc/ Rc/ M0 X. M X. M X. M X. M X. M X Q V X F Installation dimensions FD 7 FF F 0 Fj With switch M FH FL FM D RD HD Q QD ote : Refer to age 7 for HD, RD dimensions and dimensions of projecting section of color indicator type, preventive maintenance output switch. QE

36 SQ Series Dimensions Head side flange type (FB) head side position locking V Q F + stroke length LL + stroke length RD HD D QB F FM FL O ushion needle EE (port) Q FH F QE Width across flats B MM J e FJ + stroke length FD QD QF Q View ote : RD and HD in the dimensions indicate the switch end positions, and and D indicate the switch rail end positions. Head side flange type (FB) head side position locking basic dimensions Q B EE F J LL M MM O Q 7. Rc/ Rc/ Rc/ Rc/ Rc/ Rc/ M0 X. M X. M X. M X. M X. M X V F F Installation dimensions With switch FD 7 FJ FL FM F D RD HD QB Q ote : Refer to age 7 for HD, RD dimensions and dimensions of projecting section of color indicator type, preventive maintenance output switch. QD 7.. QE QF

37 Dimensions SQ Series Double acting position locking type Head side flange type (FB) rod side position locking FM Q EE (port) FL O ushion needle V QB F + stroke length LL + stroke length RD HD D Q F QE F FH Width across flats B MM J e QF View QD Q FD FJ + stroke length ote : RD and HD in the dimensions indicate the switch end positions, and and D indicate the switch rail end positions. Head side flange type (FB) rod side position locking basic dimensions Q B EE F J LL M MM O Q 7. Rc/ Rc/ Rc/ Rc/ Rc/ Rc/ M0 X. M X. M X. M X. M X. M X V F F Installation dimensions With switch FD 7 FJ FL FM F D RD HD QB Q ote : Refer to age 7 for HD, RD dimensions and dimensions of projecting section of color indicator type, preventive maintenance output switch. QD 7.. QE QF

38 SQ Series Dimensions Eye bracket type () head side position locking O + stroke length V Q RD LL + stroke length HD D QB F I ushion needle Q EE (port) Q R E QE Width across flats B MM J e D H0 J + stroke length QD Q QF View ote : RD and HD in the dimensions indicate the switch end positions, and and D indicate the switch rail end positions. Eye bracket type () head side position locking basic dimensions B EE F J 7. Rc/ Rc/ Rc/ Rc/ Rc/ Rc/ Installation dimensions V D E F I J Q LL M MM O Q QB Q QD QE M0 X. M X. 7 M X. 0 M X. 0 M X. M X. With switch D.... RD HD ote : Refer to age 7 for HD, RD dimensions and dimensions of projecting section of color indicator type, preventive maintenance output switch. QF Q