APPENDIX 1: ATTACHMENT REQUIREMENTS FOR WIND UPLIFT RESISTANCE

Transcription

1 APPENDIX 1: ATTACHMENT REQUIREMENTS FOR WIND UPLIFT NCE Table Application Type Description Page 1A-1 Wood New, Reroof (Tear-Off), Recover C-1 Mechanically Attached Insulation, Bonded Roof Cover 4 1A-2 Wood New, Reroof (Tear-Off), Recover C-2 Plate-Bonded Roof Cover 4 1B Wood New, Reroof (Tear-Off), Recover D-1 Insulated, Mechanically Attached Roof Cover 5 1C Wood New, Reroof (Tear-Off), Recover E Non-Insulated, Mechanically Attached Roof Cover 5 2A-1 Steel or Conc. New, Reroof (Tear-Off), Recover B-1 Mech. Attached Base Insulation, Bonded Top Insulation, Bonded Roof Cover 6-9 2A-2 Steel or Conc. New, Reroof (Tear-Off), Recover B-2 Mech. Attached Base Insulation, Bonded Temp Roof, Bonded Top Insulation, Bonded Roof Cover 10 2B-1 Steel or Conc. New, Reroof (Tear-Off), Recover C-1 Mechanically Attached Insulation, Bonded Roof Cover B-2 Steel or Conc. New, Reroof (Tear-Off), Recover C-2 Plate-Bonded Roof Cover C-1 Steel or Conc. New, Reroof (Tear-Off), Recover D-1 Insulated, Mechanically Attached Roof Cover (Stress Plates) C-2 Steel or Conc. New, Reroof (Tear-Off), Recover D-1 Insulated, Mechanically Attached Roof Cover (Battens) A-1 Concrete New, Reroof (Tear-Off) A-1A Bonded Insulation, Bonded Roof Cover A-2 Concrete New, Reroof (Tear-Off) A-1B Bonded Temp Roof, Bonded Insulation, Bonded Roof Cover B Concrete New, Reroof (Tear-Off) F Non-Insulated, Bonded Roof Cover 35 4A LWIC New, Reroof (Tear-Off) A-1A Bonded Insulation, Bonded Roof Cover B LWIC New, Reroof (Tear-Off) or Recover D-1 Insulated, Mechanically Attached Roof Cover 43 4C LWIC New, Reroof (Tear-Off) F Non-Insulated, Bonded Roof Cover A CWF New, Reroof (Tear-Off) A-1A Bonded Insulation, Bonded Roof Cover 46 5B CWF New, Reroof (Tear-Off) A-2 Mech. Attached Anchor Sheet, Bonded Insulation, Bonded Roof Cover 46 6A Gypsum Reroof (Tear-Off) A-1A Bonded Insulation, Bonded Roof Cover 47 6B Gypsum Reroof (Tear-Off) A-2 Mech. Attached Anchor Sheet, Bonded Insulation, Bonded Roof Cover 48 7A Various Recover A-1A Bonded Insulation, Bonded Roof Cover B Steel Recover C-2 Plate-Bonded Roof Cover 56 7C Steel Recover D-1 Insulated, Mechanically Attached Roof Cover 56 7D Steel Recover D-2 Insulated, Mechanically Attached Roof Cover (RMA Strips) 56 7E Steel Recover E Non-Insulated, Mechanically Attached Roof Cover 57 7F Various Recover F Non-Insulated, Bonded Roof Cover 57 Prepared by: Robert Nieminen, PE Appendix 1, Page 1 of 57

2 The following notes apply to the systems outlined herein: 1. The evaluation herein pertains to above-deck roof components; deck-attachment details pertain to as-tested conditions under TAS 114, Appendix J. Roof decks shall be in accordance with FBC (HVHZ) requirements to the satisfaction of the AHJ. 2. Unless otherwise noted, fasteners and stress plates for insulation attachment shall be as follows. Fasteners shall be of sufficient length for the following engagements: Wood : Firestone All-Purpose or Heavy-Duty Fasteners with Firestone Insulation Fastening Plates. Minimum 1-inch plywood penetration or wood plank embedment. Steel : Firestone All-Purpose or Heavy-Duty Fasteners with Firestone Insulation Fastening Plates. Minimum ¾-inch steel penetration, engage the top flute of the steel deck. Concrete : Firestone Heavy-Duty or Concrete Drive Fasteners with Firestone Insulation Fastening Plates. Minimum 1.25-inch embedment. Fasteners installed with a pilot hole in accordance with the fastener manufacturer s published installation instructions. 3. Unless otherwise noted, insulation may be any one layer or combination of polyisocyanurate, polystyrene, wood fiberboard, perlite or gypsum-based roof board that meets the QA requirements of F.A.C. Rule 61G20-3 and is documented as meeting FBC (HVHZ) 1516 and, for foam plastic, FBC Chapter 26, when installed with the roof cover. 4. If mechanical attachment to the structural deck through lightweight insulating is proposed, field withdrawal resistance testing shall be performed to confirm equivalent or determine enhanced fastening patterns and density. All testing and fastening design shall be in compliance with Testing Application Standard TAS 105 and Roofing Application Standard RAS 117 and/or RAS 137. Calculations shall be prepared, signed and sealed by a qualified design professional. 5. Preliminary insulation attachment for Types C-2 and D = Minimum four fasteners per 4 x 8 ft board or minimum two fasteners per 4 x 4 ft board. 6. Unless otherwise noted, insulation adhesive application rates are as follows. Ribbon or bead width is at the time of application; the ribbons/beads shall expand as noted in the manufacturer s published instructions: Firestone : Continuous ½ to ¾-inch beads, 12- Firestone : Continuous ¾ to 1-inch wide ribbons, 12- Firestone : Continuous ¾ to 1-inch wide ribbons, 12- Firestone : Continuous ¾ to 1-inch wide ribbons, 12-3M CR-20: Continuous 2½ to 3½-inch ribbons, 12- Note: When multiple layers(s) of insulation and/or coverboard are installed in ribbon-applied adhesive, adhesive ribbons shall be staggered from layer-to-layer a distance of one-half the ribbon spacing. Note: The maximum edge distance from the adhesive ribbon to the edge of the insulation board shall be not less than one-half the specified ribbons spacing. 7. Unless otherwise noted, all insulations are flat stock or taper board of the minimum thickness noted. Tapered ISO 95+ or Tapered at the following thickness limitations may be substituted with the following Maximum Design Pressure () limitations. In no case shall these values be used to increase the listings in the tables; rather if listing below meets or exceeds that listed for a particular system in the tables, then the thinner board listed below may be used as a drop-in for the equivalent thicker material listed in the table. Firestone : psf (Min. 0.5-inch thick) Firestone : psf (Min. 0.5-inch thick) Firestone : psf (Min. 0.5-inch thick) Firestone : psf (Min. 0.5-inch thick) 3M CR-20: psf (Min. 1.0-inch thick Tapered ISO 95+ only) 8. Bonded polyisocyanurate insulation boards shall be maximum 4 x 4 ft. 9. Perimeter and corner areas shall comply with the enhanced uplift pressure requirements of these areas. Fastener densities shall be increased, as calculated in compliance with Roofing Application Standard RAS 117 and/or RAS 137 by a qualified design professional. *This extrapolation is not permitted for systems marked with an asterisk*. Prepared by: Robert Nieminen, PE Appendix 1, Page 2 of 57

3 10. For assemblies marked with an asterisk*, the maximum design pressure () limitation listed shall be applicable to all roof pressure zones (i.e., field, perimeters and corners). Neither rational analysis, nor extrapolation is permitted for enhanced attachment at enhanced pressure zones (i.e., perimeters, corners and extended corners). 11. Fastener spacing for mechanical attachment is based on a minimum fastener resistance value in conjunction with the maximum design pressure () listed for a specific system. Should the fastener resistance be less than that required, as determined by the Building Official, a revised fastener spacing prepared, signed and sealed by a qualified design professional may be submitted. Said revised fastener spacing shall utilize the withdrawal resistance value taken from Testing Application Standard TAS 105 and calculations in compliance with Roofing Application Standard RAS 117 or RAS For bonded insulation or membrane over existing substrates in a recover installation, the existing roof system shall be capable of resisting project design pressures on its own merit to the satisfaction of the AHJ, as documented through field uplift testing in accordance with TAS For Type D, steel deck applications, the roof membrane shall be run with its length perpendicular to the steel deck flutes. 14. For recover installations, the existing roof shall be examined in accordance with FBC For Recover Applications using Type C-2 or D, the insulation is optional. Alternatively, ISOGARD HD, ISO 95+,, other polyisocyanurate, Dens, Dens Prime,, SECUROCK Glass-Mat Roof Board, GreenGuard Roofing Insulation Boards, Insulfoam EPS with necessary slip sheet or wood fiberboard may be used as a separator board, preliminarily attached prior to roof cover installation. The separator component shall be documented as meeting FBC (HVHZ) 1516 and, for foam plastic, FBC Chapter 26, when installed with the roof cover in Recover applications. 15. For membrane attachment using batten-strips, batten-strip end laps shall be spliced with sufficient dimension to allow for minimum 2-fasteners at each batten-strip lap. 16. For adhered membrane systems, side laps shall be minimum 3-inch wide sealed with min. 1.5-inch heat weld. Membrane adhesive application rates are as follows: Membrane Adhesive Method Rate UltraPly Bonding Adhesive (UP-BA) Contact Application 45 to 60 ft 2 /gal Water Based Bonding Adhesive-S (WBBA-S) Contact Application 100 to 120 ft 2 /gal. Water Based Bonding Adhesive-P () Contact Application 100 to 120 ft 2 /gal. Single-Ply LVOC Bonding Adhesive (LVOC-BA) Contact Application 45 to 60 ft 2 /gal Single-Ply LVOC Bonding Adhesive (LVOC-BA-) Contact Application 45 to 60 ft 2 /gal XR XR Bonding Adhesive (XR-BA) Substrate Application 70 to 90 ft 2 /gal XR Water Based Bonding Adhesive-P () Substrate Application 100 to 120 ft 2 /gal. XR XR Stick Membrane Adhesive Substrate Application Continuous ¾ to 1-inch wide ribbons XR Substrate Application Continuous ¾ to 1-inch wide ribbons 17. For InvisiWeld installations, care shall be taken to ensure that the InvisiWeld Plates do not line-up with seams in the TPO membrane. This condition precludes proper induction welding of the membrane to the InvisiWeld Plates. 18. Vapor Barrier / Temp Roof noted herein consists of 1 or 2 plies Type IV (4) M or Type VI (6) M or 1 ply MB Base, SBS Base, SBS PolyBase or SBS Premium Base in hot asphalt. 19. An optional air/vapor barrier of V-Force Vapor Barrier Membrane, self-adhered, may be installed atop steel roof decks (Tables 2A through 2C) prior to installation of any steel deck roof assembly noted herein. 20. = Maximum Design Pressure is the result of testing for wind load resistance based on allowable wind loads. Refer to FBC (HVHZ) 1620 and RAS 128 for determination of design wind pressures. Prepared by: Robert Nieminen, PE Appendix 1, Page 3 of 57

4 TABLE 1A-1: WOOD DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE C-1: MECHANICALLY ATTACHED INSULATION, BONDED ROOF COVER Type Fasten Attach ULTRAPLY TPO SYSTEMS W-1. W-2. W-3. W-4. W-5. Min. 19/32-inch plywood or wood plank; 24 span; 8d nails 6 Min. 19/32-inch plywood or wood plank; 24 span; x 2-3/8 ring shank nails 6 Min. 19/32-inch plywood or wood plank; 24 span; 8d nails 6 Min. 19/32-inch plywood or wood plank; 24 span; 8d nails 6 Min. 19/32-inch plywood or wood plank; 24 span; x 2-3/8 ring shank nails 6 Min. 2-inch ISO 95+ See Note 2 1 per 1.78 ft 2 LVOC-BA-, WBBA-S, Min. 1-inch See Note 2 1 per 1.6 ft 2 LVOC-BA-, LVOC-BA Min. 0.5-inch SECUROCK Gypsum-Fiber Roof Board, Dens or Dens Prime Min. 0.5-inch SECUROCK Gypsum-Fiber Roof Board or Dens Prime Min. 0.5-inch SECUROCK Gypsum-Fiber Roof Board See Note 2 1 per 1.6 ft 2 WBBA-S, See Note 2 1 per 1.6 ft 2 / LVOC-BA See Note 2 1 per 1.78 ft 2 LVOC-BA-, LVOC-BA TABLE 1A-2: WOOD DECKS - NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE C-2: PLATE-BONDED ROOF COVER Insulation Layer Fasten Attach Density / Pattern Roof Cover W-6. Min. 19/32-inch plywood or wood plank; 24 span; 8d nails 6 (Optional) One or more layers,, preliminarily attached Firestone Heavy Duty Fasteners and InvisiWeld Plates Max. 6- in rows max. 72- bonded to InvisiWeld Plates with RhinoBond Portable Plate Bonding Tool and weighted RhinoBond Cooling Clamps W-7. Min. 19/32-inch plywood or wood plank; 24 span; 8d nails 6 (Optional) One or more layers,, preliminarily attached Firestone Heavy Duty Fasteners and InvisiWeld Plates 12 parts per 4 x 8 ft board bonded to InvisiWeld Plates with 1 per 2.67 ft 2 RhinoBond Portable Plate Bonding Tool and weighted RhinoBond Cooling Clamps W-8. Min. 19/32-inch plywood or wood plank; 24 span; #8 screws 6 (Optional) One or more layers,, preliminarily attached Firestone Heavy Duty Fasteners and InvisiWeld Plates Max. 6- in rows max. 60- bonded to InvisiWeld Plates with RhinoBond Portable Plate Bonding Tool and weighted RhinoBond Cooling Clamps Prepared by: Robert Nieminen, PE Appendix 1, Page 4 of 57

5 W-9. W-10. Min. 19/32-inch plywood or wood plank; 24 span; 8d nails 6 Min. 19/32-inch plywood or wood plank; 24 span; 10d nails 4 at perimeter; 8d nails 6 in field TABLE 1B: WOOD DECKS - NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE D-1: INSULATED, MECHANICALLY ATTACHED ROOF COVER Insulation Roof Cover Type Attach Membrane Fasten Attach Optional min. 1-inch ISO 95+ or followed by min inch Dens, Dens Prime or SECUROCK Gypsum-Fiber Roof Board, min. 0.5-inch ISOGARD HD, min. 1-inch or min inch ISOGARD HD Composite Prelim. attached Prelim. attached (min. 60-mil) Firestone HD Fasteners with Firestone HD Seam Plates Firestone HD Fasteners with Firestone HD Seam Plates 5- within 6-inch wide laps spaced 114- Laps sealed with 1.5-inch heat weld. 6- within 6-inch wide laps spaced Laps sealed with 5-inch heat weld that encapsulates plates TABLE 1C: WOOD DECKS - NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE E: NON-INSULATED, MECHANICALLY ATTACHED ROOF COVER Roof Cover Membrane Fasten Attach W-11. Min. 19/32-inch plywood or wood plank; 24 span; 8d nails 6 Firestone HD Fasteners with Firestone HD Seam Plates 6- within 6-inch wide laps spaced 72- Laps sealed with 1.5-inch heat weld Prepared by: Robert Nieminen, PE Appendix 1, Page 5 of 57

6 TABLE 2A-1: STEEL OR CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE B-1: MECHANICALLY FASTENED BASE INSULATION, BONDED TOP INSULATION, BONDED ROOF COVER Type Fastener Attach Type Attach ULTRAPLY TPO SYSTEMS SC-1. Min. 22 ga., type B, Grade 33 steel or strutural 2 Optional min. 1.5-inch ISO 95+ followed by See Note 2 1 per 2 ft min. 0.5-inch Tapered ISO 95+ LVOC-BA-, WBBA-S, SC-2. Min. 22 ga., type B, Grade 33 steel or strutural Min. 1.5-inch See Note 2 1 per 2.7 ft 2 Optional min. 1.5-inch followed by min. 0.5-inch Tapered ; ; ; LVOC-BA- SC-3. Min. 22 ga., type B, Grade 33 steel or strutural 2 Optional min. 1.5-inch followed by Min. 2-inch See Note 2 1 per 4 ft min. 0.5-inch Tapered ; ; ; LVOC-BA- SC-4. Min. 22 ga., type B, Grade 33 steel or strutural Min. 2-inch ISO 95+ See Note 2 1 per 4 ft 2 Min. 1.5-inch ISOGARD HD Composite ; ; ; LVOC-BA- SC-5. Min. 22 ga., type B, Grade 33 steel or strutural See Note 2 ; ; 1 per 2.7 ft 2 Min. 1.5-inch ISOGARD HD Composite ; LVOC-BA- SC-6. Min. 22 ga., type B, Grade 33 steel or strutural See Note 2 1 per 2 ft 2 Min. 0.5-inch ISOGARD HD LVOC-BA-, LVOC-BA SC-7. Min. 22 ga., type B, Grade 33 steel or strutural Min. 2-inch ISO 95+ See Note 2 1 per 2 ft 2 Min. 0.5-inch ISOGARD HD ; ; LVOC-BA-, LVOC-BA SC-8. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or strutural Min. 2-inch ISO 95+ See Note 2 1 per 1 ft 2 Min. 0.5-inch ISOGARD HD ; ; / WBBA-S, -S SC-9. Min. 22 ga., type B, Grade 33 steel or strutural See Note 2 1 per 2 ft 2 Min inch Dens, Dens Prime or, I.S.O. Stick or 3M CR-20 / UP-BA SC-10. Min. 22 ga., type B, Grade 33 steel or strutural See Note 2 1 per 2 ft 2 Min inch Dens Prime or SECUROCK, I.S.O. Stick or 3M CR-20 / LVOC-BA- SC-11. Min. 22 ga., type B, Grade 33 steel or strutural See Note 2 1 per 2 ft 2 inch Tapered ISO 95+ followed by min Optional min. 1.5-inch ISO 95+ or min inch ISOGARD HD LVOC-BA-, WBBA-S, SC-12. Min. 22 ga., type B, Grade 33 steel or strutural Min. 0.5-inch Dens Prime or SECUROCK Gypsum-Fiber Roof Board See Note 2 1 per 4 ft 2 Optional min. 1.5-inch followed by min. 0.5-inch Tapered ; ; ; LVOC-BA- Prepared by: Robert Nieminen, PE Appendix 1, Page 6 of 57

7 SC-13. SC-14. SC-15. SC-16. SC-17. SC-18. SC-19. SC-20. SC-21. SC-22. SC-23. SC-24. Min. 22 ga., type B, Grade 33 steel or strutural Min. 22 ga., type B, Grade 33 steel or strutural Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or strutural Min. 22 ga., type B, 50 ksi steel; 6 spans; #12-24 x 1-1/4 HWH screw 6 or strutural Min. 22 ga., type B, 50 ksi steel; 6 spans; 5/8 puddle welds 6 or strutural Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or strutural Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or strutural Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or strutural Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or strutural Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or strutural Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or strutural Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or strutural TABLE 2A-1: STEEL OR CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE B-1: MECHANICALLY FASTENED BASE INSULATION, BONDED TOP INSULATION, BONDED ROOF COVER Type Fastener Attach Type Attach Min. 0.5-inch Dens, Dens Prime or SECUROCK Gypsum- Fiber Roof Board Min. 0.5-inch Dens, Dens Prime or SECUROCK Gypsum- Fiber Roof Board or See Note 2 1 per 2 ft 2 followed by min inch FiberTop C or S See Note 2 1 per 2 ft 2 inch Dens Prime or SECUROCK Gypsum- followed by Min Fiber Roof Board See Note 2 See Note 2 Min. 2-inch ISO 95+ See Note 2 or See Note 2 Min. 2-inch ISO 95+ See Note 2 1 per 1.6 ft 2 Min. 0.5-inch Dens Prime or SECUROCK ; ; ; ; ; ;, 6-inch LVOC-BA- LVOC-BA-, WBBA-S, -S LVOC-BA- 1 per 1.78 ft 2 Min. 1.5-inch ISOGARD HD Composite, 12- LVOC-BA- 1 per 1.78 ft 2 Min inch SECUROCK Gypsum-Fiber Roof Board Min. 2-inch ISO 95+ See Note 2 1 per 1 ft 2 Min. 0.5-inch ISOGARD HD Min. 2-inch ISO 95+ See Note 2 1 per 1 ft 2, 6- LVOC-BA- 1 per 1.6 ft 2 or LVOC-BA- ; ; 1 per 1.6 ft 2 Min. 0.5-inch ISOGARD HD ;, 6-2 Min. 0.5-inch Dens Prime or SECUROCK Min. 2-inch ISO 95+ See Note 2 1 per 1 ft ; ; ;, 4- ; ;, 4-inch ; ; ;, 4- Min. 2-inch ISO 95+ See Note 2 1 per 1 ft 2, 6-2 followed by min Min. 2-inch ISO 95+ See Note 2 1 per 1 ft inch ISOGARD HD or min. 19/32-inch plywood, 6- LVOC-BA- LVOC-BA- / WBBA-S, LVOC-BA- LVOC-BA- LVOC-BA- Prepared by: Robert Nieminen, PE Appendix 1, Page 7 of

8 TABLE 2A-1: STEEL OR CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE B-1: MECHANICALLY FASTENED BASE INSULATION, BONDED TOP INSULATION, BONDED ROOF COVER Type Fastener Attach Type Attach SC-25. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or strutural Min. 2-inch ISO 95+ See Note 2 1 per 1 ft 2 ; ;, 4-inch LVOC-BA SC-26. Min. 22 ga., type B, Grade 33 steel; 6 spans; two (2) Traxx/5 screws 6 or strutural Min. 1.5-inch See Note 2 1 per 1 ft 2 Min. 1.5-inch ; ; LVOC-BA SC-27. Min. 22 ga., type B, Grade 80 steel; 6 spans; two (2) Traxx/5 screws 6 or strutural Min. 2-inch ISO 95+ See Note 2 1 per 1 ft 2 ; ;, 4-inch LVOC-BA SC-28. Min. 22 ga., type B, Grade 80 steel; 6 spans; two (2) Traxx/5 screws 6 or strutural Min. 2-inch ISO 95+ See Note 2 1 per 1 ft 2 Min. 0.5-inch ISOGARD HD ; ; ;, 4- LVOC-BA ULTRAPLY TPO XR SYSTEMS: SC-29. Min. 22 ga., type B, Grade 33 steel or strutural Min. 0.5-inch Dens, Dens Prime or SECUROCK Gypsum- Fiber Roof Board See Note 2 1 per 2 ft 2 inch FiberTop C or S or Min inch Dens Prime or SECUROCK Gypsum-Fiber Roof followed by min Board ; ; XR / XR-BA SC-30. Min. 22 ga., type B, Grade 33 steel or strutural Min inch ISO 95+ See Note 2 1 per 4 ft 2 ; ; ; XR / I.S.O. Spray S, XR Stick, 12-inch SC-31. Min. 22 ga., type B, Grade 33 steel or strutural Min. 0.5-inch Dens or SECUROCK Gypsum- Fiber Roof Board See Note 2 1 per 2 ft 2 followed by optional min. 0.5-inch FiberTop C or S wood fiber, Min. 0.5-inch Dens Prime or SECUROCK or min. 19/32-inch plywood XR / I.S.O. Spray S, XR Stick, 12-inch SC-32. Min. 22 ga., type B, Grade 33 steel or strutural Min. 0.5-inch Dens or SECUROCK Gypsum- Fiber Roof Board 2 followed by min See Note 2 1 per 2 ft inch ISOGARD HD XR / I.S.O. Spray S, XR Stick, 4-inch SC-33. Min. 22 ga., type B, Grade 33 steel or strutural See Note 2 1 per 2 ft 2 inch FiberTop C or S wood fiber or Min inch Dens Prime or SECUROCK Gypsum- followed by min Fiber Roof Board ; ; ; XR / I.S.O. Spray S, XR Stick, 12-inch SC-34. Min. 22 ga., type B, Grade 33 steel or strutural 2 Optional min. 1-inch ISO 95+ followed by See Note 2 1 per 2 ft min. 0.5-inch ISOGARD HD ; ; ; XR / I.S.O. Spray S, XR Stick, 12-inch SC-35. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or strutural See Note 2 1 per 1.6 ft 2 Min. 0.5-inch Dens Prime or SECUROCK ; ; ;, 6- XR / I.S.O. Spray S, XR Stick, 6-inch Prepared by: Robert Nieminen, PE Appendix 1, Page 8 of 57

9 TABLE 2A-1: STEEL OR CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE B-1: MECHANICALLY FASTENED BASE INSULATION, BONDED TOP INSULATION, BONDED ROOF COVER Type Fastener Attach Type Attach SC-36. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or strutural Min. 2-inch ISO 95+ See Note 2 ; ; 1 per 1.6 ft 2 ;, 6- XR / I.S.O. Spray S, XR Stick, 6-inch SC-37. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or strutural Min. 2-inch ISO 95+ See Note 2 1 per 1.6 ft 2 Min. 0.5-inch ISOGARD HD ; ; ;, 6- XR / I.S.O. Spray S; XR Stick, 6-inch SC-38. Min. 22 ga., type B, Grade 33 steel; 6 spans; two (2) Traxx/5 screws 6 or strutural 2 Min. 0.5-inch Dens Prime or SECUROCK Min. 2-inch ISO 95+ See Note 2 1 per 1 ft ; ;, 4-inch XR / I.S.O. Spray S, XR Stick, 4-inch Prepared by: Robert Nieminen, PE Appendix 1, Page 9 of 57

10 TABLE 2A-2: STEEL OR CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE B-2: MECHANICALLY FASTENED BASE INSULATION, BONDED TEMP ROOF, BONDED TOP INSULATION, BONDED ROOF COVER Insulation Temp Roof Type Fasten Attach Type Attach ULTRAPLY TPO SYSTEMS SC-39. Min. 22 ga., type B, Grade 33 steel or struct. conc. Min inch FM Approved perlite See Note 2 1 per 2 ft 2 Type IV or Type VI in hot Two plies Firestone asphalt followed by Min inch Dens Prime or SECUROCK Gypsum-Fiber Roof Board Hot asphalt or I.S.O. Stick LVOC-BA-, LVOC- BA, WBBA-S, SC-40. SC-41. SC-42. Min. 22 ga., type B, Grade 33 steel or struct. conc. Min. 22 ga., type B, Grade 33 steel or struct. conc. Min. 22 ga., type B, Grade 33 steel or struct. conc. Min inch Dens or min. 0.5-inch SECUROCK Gypsum- Fiber Roof Board Min inch Dens or min. 0.5-inch SECUROCK Gypsum- Fiber Roof Board Min inch Dens or min. 0.5-inch SECUROCK Gypsum- Fiber Roof Board See Note 2 1 per 4 ft 2 Force Vapor Barrier Membrane, selfadhered V-Force SB ; V- See Note 2 1 per 4 ft 2 Force Vapor Barrier Membrane, selfadhered V-Force SB ; V- See Note 2 1 per 4 ft 2 Force Vapor Barrier Membrane, selfadhered V-Force SB ; V- One or more layers min. 1.5-inch ISO 95+, optional min. 0.5-inch Tapered ISO 95+ One or more layers min. 1.5-inch ISO 95+, optional min. 0.5-inch Tapered ISO 95+ ; Min. 0.5-inch FiberTop C or S or ISOGARD HD or Min inch Dens Prime or SECUROCK Gypsum-Fiber Roof Board; or Min. 19/32-inch plywood One or more layers min. 1.5-inch ISO 95+, optional min. 0.5-inch Tapered ISO 95+ ; Min inch Dens or LVOC-BA-, LVOC- BA, WBBA-S, LVOC-BA-, LVOC- BA, WBBA-S, LVOC-BA, WBBA-S, ULTRAPLY TPO XR SYSTEMS SC-43. Min. 22 ga., type B, Grade 33 steel or struct. conc. Min inch Dens or min. 0.5-inch SECUROCK Gypsum- Fiber Roof Board See Note 2 1 per 4 ft 2 Force Vapor Barrier Membrane, selfadhered V-Force SB ; V- One or more layers min. 1.5-inch ISO 95+, optional min. 0.5-inch Tapered ISO 95+ ; Min. 0.5-inch FiberTop C or S or Min inch Dens Prime or XR / XR-BA Prepared by: Robert Nieminen, PE Appendix 1, Page 10 of 57

11 TABLE 2B-1: STEEL OR CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE C-1: MECHANICALLY ATTACHED INSULATION, BONDED ROOF COVER Type Fasten Attach ULTRAPLY TPO SYSTEMS SC-44. Min. 22 ga., type B, Grade 33 steel or strutural Min. 2-inch ISO 95+ See Note 2 1 per 4 ft 2 LVOC-BA- SC-45. Min. 22 ga., type B, Grade 33 steel or strutural Min inch ISO 95+ See Note 2 1 per 2.67 ft 2 LVOC-BA-, WBBA-S, SC-46. Min. 22 ga., type B, Grade 33 steel or strutural See Note 2 1 per 2 ft 2 LVOC-BA- SC-47. Min. 22 ga., type B, 50 ksi steel; 6 spans; 5/8 puddle welds 6 or strutural Min. 2-inch ISO 95+ See Note 2 1 per 2.67 ft 2 LVOC-BA SC-48. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or strutural Min. 2-inch ISO 95+ See Note 2 1 per 2.67 ft 2 LVOC-BA SC-49. Min. 22 ga., type B, Grade 33 steel or strutural Min. 1.5-inch See Note 2 1 per 2.67 ft 2 LVOC-BA-, WBBA-S, SC-50. Min. 22 ga., type B, Grade 33 steel or strutural Min. 1-inch See Note 2 1 per 2 ft 2 LVOC-BA-, WBBA-S, SC-51. Min. 22 ga., type B, Grade 33 steel or strutural Min. 1.5-inch ISOGARD HD Composite See Note 2 1 per 4 ft 2 LVOC-BA-, WBBA-S, SC-52. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or strutural Min. 1.5-inch ISOGARD HD Composite See Note 2 1 per 1.33 ft 2 / WBBA-S, SC-53. Min. 22 ga., type B, Grade 33 steel or strutural One or more layers, any Min. 0.5-inch ISOGARD HD See Note 2 1 per 2.67 ft 2 LVOC-BA- SC-54. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or strutural one or more layers, any Min. 0.5-inch ISOGARD HD See Note 2 1 per 1.33 ft 2 / WBBA-S, SC-55. Min. 22 ga., type B, Grade 33 steel or strutural (Optional for Recover) Min. 0.5-inch thick, any Min. 0.5-inch Dens Prime See Note 2 1 per 2.67 ft 2 LVOC-BA, WBBA-S SC-56. Min. 22 ga., type B, Grade 33 steel or strutural One or more layers, any Min inch SECUROCK See Note 2 1 per 2 ft 2 LVOC-BA-, WBBA-S, SC-57. Min. 22 ga., type B, 50 ksi steel; 6 spans; 5/8 puddle welds 6 or strutural One or more layers, any Min inch SECUROCK See Note 2 1 per 1.78 ft 2 LVOC-BA Prepared by: Robert Nieminen, PE Appendix 1, Page 11 of 57

12 TABLE 2B-1: STEEL OR CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE C-1: MECHANICALLY ATTACHED INSULATION, BONDED ROOF COVER Type Fasten Attach SC-58. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 one or more layers, any Min. 19/32-inch plywood Firestone HD HailGard Fastener 1 per 2.67 ft 2 LVOC-BA SC-59. Min. 22 ga., type B, 50 ksi steel; 6 spans; #12-24 x 1-1/4 HWH screw 6 or strutural Min. 1-inch See Note 2 1 per 1.6 ft 2 LVOC-BA SC-60. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 one or more layers, any Min. 19/32-inch plywood Firestone HD HailGard Fastener 1 per 1.6 ft 2 LVOC-BA SC-61. Min. 22 ga., type B, Grade 33 steel; 6 spans; 5/8 puddle weld 6 or strutural See Note 2 1 per 1.78 ft 2 LVOC-BA SC-62. Min. 22 ga., type B, 50 ksi steel; 6 spans; #12-24 x 1-1/4 HWH screw 6 or strutural One or more layers, any Min. 0.5-inch SECUROCK See Note 2 1 per 1.78 ft 2 LVOC-BA SC-63. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or strutural one or more layers, any Min. 0.5-inch ISOGARD HD See Note 2 1 per 1.33 ft 2 LVOC-BA SC-64. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or strutural Min. 1-inch ISOGARD HD Composite See Note 2 1 per 1.33 ft 2 LVOC-BA SC-65. Min. 22 ga., type B, Grade 33; 6 spans; Traxx/5 screw 6 steel or strutural one or more layers, any Min. 0.5-inch Dens Prime or SECUROCK See Note 2 1 per 1.33 ft 2 LVOC-BA SC-66. Min. 22 ga., type B, Grade 33; 6 spans; Traxx/5 screw 6 steel or strutural one or more layers, any Min. 19/32-inch plywood Firestone Insulation Fastening Plates Firestone HD Fasteners or Firestone Concrete Drive ( only) 1 per 2 ft 2 LVOC-BA SC-67. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or strutural Min. 2-inch ISO 95+ See Note 2 1 per 1.6 ft 2 LVOC-BA SC-68. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or strutural Min. 1.5-inch See Note 2 1 per 1.6 ft 2 LVOC-BA SC-69. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or strutural Min. 2-inch See Note 2 1 per 1 ft 2 / WBBA-S, Prepared by: Robert Nieminen, PE Appendix 1, Page 12 of 57

13 TABLE 2B-1: STEEL OR CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE C-1: MECHANICALLY ATTACHED INSULATION, BONDED ROOF COVER Type Fasten Attach SC-70. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or strutural Min. 2-inch See Note 2 1 per 1.6 ft 2 LVOC-BA SC-71. Min. 22 ga., type B, 60 ksi steel; 6 spans; 5/8 puddle welds 6 or strutural One or more layers, any Min. 0.5-inch SECUROCK See Note 2 1 per 1.78 ft 2 / UP-BA SC-72. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or strutural See Note 2 1 per 1.33 ft 2 LVOC-BA SC-73. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or strutural Min. 2-inch See Note 2 1 per 1.33 ft 2 LVOC-BA SC-74. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or strutural one or more layers, any Min. 0.5-inch Dens Prime or SECUROCK See Note 2 1 per 1 ft 2 LVOC-BA SC-75. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or strutural Min. 2-inch ISO 95+ See Note 2 1 per 1 ft 2 / UP-BA SC-76. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or strutural Min. 2-inch See Note 2 1 per 1 ft 2 LVOC-BA SC-77. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or strutural Min. 1.5-inch ISOGARD HD Composite See Note 2 1 per 1.33 ft 2 LVOC-BA SC-78. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or strutural one or more layers, any Min. 0.5-inch SECUROCK See Note 2 1 per 1 ft 2 LVOC-BA SC-79. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or strutural Min. 2-inch ISOGARD HD Composite See Note 2 1 per 1.33 ft 2 LVOC-BA SC-80. Min. 22 ga., type B, Grade 80 steel; 6 spans; two (2) Traxx/5 screws 6 or strutural Min. 2-inch ISO 95+ See Note 2 1 per 1 ft 2 / UP-BA SC-81. Min. 22 ga., type B, Grade 80 steel; 6 spans; two (2) Traxx/5 screws 6 or strutural Min. 2-inch See Note 2 1 per 1 ft 2 LVOC-BA Prepared by: Robert Nieminen, PE Appendix 1, Page 13 of 57

14 TABLE 2B-1: STEEL OR CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE C-1: MECHANICALLY ATTACHED INSULATION, BONDED ROOF COVER Type Fasten Attach SC-82. Min. 22 ga., type B, Grade 33 steel; 6 spans; two (2) Traxx/5 screws 6 or strutural one or more layers, any Min. 19/32-inch plywood Firestone Insulation Fastening Plates Firestone HD Fasteners or Firestone Concrete Drive ( only) 1 per 1 ft 2 LVOC-BA ULTRAPLY TPO XR SYSTEMS SC-83. Min. 22 ga., type B, Grade 33 steel or strutural One or more layers, any Min inch Dens Prime or min. 0.5-inch SECUROCK Gypsum-Fiber Roof Board See Note 2 1 per 2.67 ft 2 XR / XR-BA SC-84. Min. 22 ga., type B, Grade 33 steel or strutural One or more layers, any Min. 0.5-inch FiberTop C or S wood fiber See Note 2 1 per 2 ft 2 XR / XR-BA SC-85. Min. 22 ga., type B, Grade 33 steel or strutural See Note 2 1 per 2 ft 2 XR /, XR Stick, 12- SC-86. Min. 22 ga., type B, Grade 33 steel or strutural Min inch ISO 95+ See Note 2 1 per 4 ft 2 XR /, XR Stick, 12- SC-87. Min. 22 ga., type B, Grade 33 steel or strutural One or more layers, any Min inch Dens Prime or SECUROCK or min. 19/32-inch plywood See Note 2 1 per 2 ft 2 XR /, XR Stick, 12- SC-88. Min. 22 ga., type B, Grade 33 steel or strutural One or more layers, any (optional for recover) Min. 0.5-inch ISOGARD HD See Note 2 1 per 2.1 ft 2 XR /, XR Stick, 12- SC-89. Min. 22 ga., type B, Grade 33 steel or strutural One or more layers, any Min. 0.5-inch ISOGARD HD See Note 2 1 per 2 ft 2 XR /, XR Stick, 4- SC-90. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or strutural Min. 2-inch ISO 95+ See Note 2 1 per 1.6 ft 2 XR /, XR Stick, SC-91. Min. 22 ga., type B, Grade 33 steel; 6 spans; two (2) Traxx/5 screws 6 or strutural Min. 2-inch ISO 95+ See Note 2 1 per 1 ft 2 XR /, XR Stick, Prepared by: Robert Nieminen, PE Appendix 1, Page 14 of 57

15 TABLE 2B-2: STEEL OR CONCRETE DECKS - NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE C-2: PLATE-BONDED ROOF COVER SC-92. SC-93. SC-94. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or min. 2,500 psi Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or min. 2,500 psi Min. 22 ga., type B, Grade 33 steel or min. 2,500 psi Vapor & Air Barrier (Optional) See Note 19 (Optional) See Note 19 (Optional) See Note 19 Insulation One or more layers,, preliminarily attached One or more layers,, preliminarily attached One or more layers, Fasten Firestone Heavy Duty Fasteners or Firestone Concrete Drive ( only) and InvisiWeld Plates Firestone Heavy Duty Fasteners or Firestone Concrete Drive ( only) and InvisiWeld Plates Firestone Heavy Duty Fasteners and UltraPly TPO InvisiWeld Plates Attach Density / Pattern Max. 12- in rows max. 60- Max. 6- in rows max per 5.33 ft² (6 parts per 4x8 ft board) Per FM LPDS 1-29 / RAS 117 Roof Cover bonded to InvisiWeld Plates with RhinoBond Portable Plate Bonding Tool and weighted RhinoBond Cooling Clamps. bonded to InvisiWeld Plates with RhinoBond Portable Plate Bonding Tool and weighted RhinoBond Cooling Clamps. bonded to InvisiWeld Plates with RhinoBond Portable Plate Bonding Tool and weighted RhinoBond Cooling Clamps SC-95. Min. 22 ga., type B, 50 ksi steel; 6 spans; #12-24 x 1-1/4 HWH screw 6 or min. 2,500 psi V-Force with min. 3- inch side laps selfadhered to top flanges of steel deck Min. 2.5-inch ISO 95+, or ISOGARD HD Composite Firestone Heavy Duty Fasteners and UltraPly TPO InvisiWeld Plates 1 per 4 ft² (8 parts per 4x8 ft board) in a 24 x 24- inch grid bonded to InvisiWeld Plates with RhinoBond Portable Plate Bonding Tool and weighted RhinoBond Cooling Clamps SC-96. Min. 22 ga., type B, 50 ksi steel; 6 spans; #12-24 x 1-1/4 HWH screw 6 or min. 2,500 psi Min inch SECUROCK Gypsum- Fiber Roof Board followed by V-Force with min. 3-inch side laps self-adhered Min. 2.5-inch ISO 95+, or ISOGARD HD Composite Firestone Heavy Duty Fasteners and UltraPly TPO InvisiWeld Plates 1 per 4 ft² (8 parts per 4x8 ft board) in a 24 x 24- inch grid bonded to InvisiWeld Plates with RhinoBond Portable Plate Bonding Tool and weighted RhinoBond Cooling Clamps SC-97. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or min. 2,500 psi (Optional) See Note 19 One or more layers, Firestone Heavy Duty Fasteners and UltraPly TPO InvisiWeld Plates 1 per 4 ft² (8 parts per 4x8 ft board) Per FM LPDS 1-29 / RAS 117 bonded to InvisiWeld Plates with RhinoBond Portable Plate Bonding Tool and weighted RhinoBond Cooling Clamps SC-98. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or min. 2,500 psi (Optional) See Note 19 One or more layers, Firestone Heavy Duty Fasteners with alternating Rows of: 1.) Firestone UltraPly TPO InvisiWeld Plates 2.) Firestone Insulation Fastening Plates 1 per 2 ft² (16 parts per 4x8 ft board) in a 12 x 24- inch grid bonded to InvisiWeld Plates with RhinoBond Portable Plate Bonding Tool and weighted RhinoBond Cooling Clamps Prepared by: Robert Nieminen, PE Appendix 1, Page 15 of 57

16 TABLE 2B-2: STEEL OR CONCRETE DECKS - NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE C-2: PLATE-BONDED ROOF COVER Vapor & Air Barrier Insulation Fasten Attach Density / Pattern Roof Cover SC-99. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screws 6, or Min. 22 ga., type B, 60 ksi steel; 6 spans; 5/8 puddle welds 6 or min. 2,500 psi (Optional) See Note 19 One or more layers, Firestone Heavy Duty Fasteners and UltraPly TPO InvisiWeld Plates 1 per 2.7 ft² (12 parts per 4x8 ft board) Per FM LPDS 1-29 / RAS 117 bonded to InvisiWeld Plates with RhinoBond Portable Plate Bonding Tool and weighted RhinoBond Cooling Clamps SC-100. Min. 22 ga., type B, Grade 33 steel; 6 spans; two (2) Traxx/5 screws 6 or min. 2,500 psi (Optional) See Note 19 One or more layers, Firestone Heavy Duty Fasteners and UltraPly TPO InvisiWeld Plates 1 per 2 ft² (16 parts per 4x8 ft board) Per FM LPDS 1-29 / RAS 117 bonded to InvisiWeld Plates with RhinoBond Portable Plate Bonding Tool and weighted RhinoBond Cooling Clamps Prepared by: Robert Nieminen, PE Appendix 1, Page 16 of 57

17 TABLE 2C-1: STEEL OR CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE D-1: INSULATED, MECHANICALLY ATTACHED ROOF COVER (STRESS PLATES) Vapor & Air Barrier Insulation Roof Cover Type Attach Membrane Fasten Attach SC-101. SC-102. SC-103. SC-104. SC-105. SC-106. Min. 22 ga., type B, Grade 33 steel ; 6 spans; Traxx/5 screw 6 or struct. conc. Min. 22 ga., type B, Grade 80 steel or min. 20 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or struct. conc. Min. 22 ga., type B, Grade 80 steel or min. 20 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or struct. conc. Min. 22 ga., type B, Grade 80 steel or min. 20 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or struct. conc. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or Min. 22 ga., type B, 60 ksi steel; 6 spans; 5/8 puddle welds 6 or struct. conc. Min. 22 ga., type B, Grade 80 steel or min. 20 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or struct. conc. (Optional) See Note 19 (Optional) See Note 19 (Optional) See Note 19 (Optional) See Note 19 (Optional) See Note 19 (Optional) See Note 19 Min. 1-inch thick, Prelim. attached Prelim. attached Prelim. attached Prelim. attached Prelim. attached Prelim. attached or TPO XR Firestone HD Fasteners or Firestone Concrete Drive ( only) with Firestone HD Seam Plates or Barbed Seam Plates Firestone HD Plus Fasteners (steel only) or Firestone Concrete Drive ( only) with Firestone HD Plus Seam Plates Firestone HD Plus Fasteners (steel only) or Firestone Concrete Drive ( only) with Firestone HD Plus Seam Plates or Wide Weld Seam Plates Firestone HD Fasteners or Firestone Concrete Drive ( only) with Firestone HD Seam Plates Firestone HD Plus Fasteners (steel only) or Firestone Concrete Drive ( only) with Firestone HD Plus Seam Plates Firestone HD Fasteners or Firestone Concrete Drive ( only) with Firestone HD Seam Plates or Wide Weld Seam Plates 12- within 6-inch wide laps spaced 72- Laps sealed with 1.5-inch heat weld. 12- within 6-inch wide laps spaced 114- Laps sealed with 1.5-inch heat weld. 12- within 6-inch wide laps spaced 114- Laps sealed with 5-inch heat weld that encapsulates plates. 12- within 6-inch wide laps spaced 90- Laps sealed with 1.5-inch heat weld. 12- within 6-inch wide laps spaced 90- Laps sealed with 1.5-inch heat weld. 12- within 6-inch wide laps spaced 90- Laps sealed with 5-inch heat weld that encapsulates plates SC-107. Min. 22 ga., type B, 60 ksi steel; 6 spans; #12-24 x 1-1/4 HWH screw 6 V-Force with min. 3-inch side laps self-adhered to top flanges of steel deck Min. 0.5-inch ISO 95+, or ISOGARD HD See Note 2 (HD only) 1 per 8 ft 2 24x72-inch grid Firestone HD Fasteners with Firestone HD Seam Plates 12- within 6-inch wide laps spaced 114- Laps sealed with 1.5-inch heat weld SC-108. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or struct. conc. (Optional) See Note 19 Prelim. attached Firestone HD Fasteners or Firestone Concrete Drive ( only) with Firestone HD Seam Plates or Barbed Seam Plates 6- within 6-inch wide laps spaced 72- Laps sealed with 1.5-inch heat weld SC-109. SC-110. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or struct. conc. Min. 22 ga., type B, 50 ksi steel; 6 spans; #12-24 x 1-1/4 HWH screw 6 (Optional) See Note 19 Min inch SECUROCK Gypsum-Fiber Roof Board followed by V-Force with min. 3-inch side laps self-adhered Min. 3-inch ISO 95+ or Prelim. attached See Note 2 (HD only) 1 per 4 ft 2 24x24-inch grid or TPO XR Firestone HD Fasteners or Firestone Concrete Drive ( only) with Firestone HD Seam Plates Firestone HD Fasteners with Firestone HD Seam Plates 6- within 6-inch wide laps spaced 114- Laps sealed with 1.5-inch heat weld. 12- within 6-inch wide laps spaced 114- Laps sealed with 1.5-inch heat weld Prepared by: Robert Nieminen, PE Appendix 1, Page 17 of 57

18 TABLE 2C-1: STEEL OR CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE D-1: INSULATED, MECHANICALLY ATTACHED ROOF COVER (STRESS PLATES) Vapor & Air Barrier Insulation Roof Cover Type Attach Membrane Fasten Attach SC-111. Min. 22 ga., type B, 60 ksi steel; 6 spans; #12-24 x 1-1/4 HWH screw 6 V-Force with min. 3-inch side laps self-adhered to top flanges of steel deck Min. 0.5-inch ISO 95+, or ISOGARD HD See Note 2 (HD only) 1 per 5.3 ft 2 24x36-inch grid, 12-inch from board edges Firestone HD Fasteners with Firestone HD Seam Plates 12- within 6-inch wide laps spaced 142- Laps sealed with 1.5-inch heat weld SC-112. Min. 22 ga., type B, Grade 80 steel; 6 spans; Traxx/5 screw 6 or struct. conc. (Optional) See Note 19 Loose Laid Firestone HD Fasteners or Firestone Concrete Drive ( only) with Firestone HD Seam Plates 6- within 6-inch wide laps spaced 142- Laps sealed with 1.5-inch heat weld SC-113. Min. 22 ga., type B, 50 ksi steel; 6 spans; 5/8 puddle welds 6 (Optional) See Note 19 Min. 0.5-inch thick, Prelim. attached Firestone HD Fasteners with Firestone HD Seam Plates 6- within 7-inch wide laps spaced 89- Laps sealed with 1.5-inch heat weld SC-114. Min. 22 ga., type B, Grade 33 steel; 6 spans; 5/8 puddle weld 6 or struct. conc. (Optional) See Note 19 Prelim. attached (min. 60-mil) Firestone HD Fasteners or Firestone Concrete Drive ( only) with Firestone HD Seam Plates 6- within 6-inch wide laps spaced 114- Laps sealed with 1.5-inch heat weld SC-115. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or struct. conc. (Optional) See Note 19 Prelim. attached Firestone HD Plus Fasteners (steel only) or Firestone Concrete Drive ( only) with Firestone HD Plus Seam Plates 6- within 6-inch wide laps spaced 142- Laps sealed with 1.5-inch heat weld SC-116. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or Min. 22 ga., type B, 60 ksi steel; 6 spans; 5/8 puddle welds 6 or struct. conc. (Optional) See Note 19 Prelim. attached or TPO XR Firestone HD Plus Fasteners (steel only) or Firestone Concrete Drive ( only) with Firestone HD Plus Seam Plates 6- within 6-inch wide laps spaced 114- Laps sealed with 1.5-inch heat weld SC-117. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or struct. conc. (Optional) See Note 19 Prelim. attached Firestone HD Plus Fasteners (steel only) or Firestone Concrete Drive ( only) with Firestone HD Plus Seam Plates 6- within 6-inch wide laps spaced 90- Laps sealed with 5-inch heat weld that encapsulates plates SC-118. Min. 22 ga., type B, 60 ksi steel; 6 spans; #12-24 x 1-1/4 HWH screw 6 Two (2) layers, V-Force with min. 3-inch side laps self-adhered Min. 3-inch ISO 95+, or ISOGARD HD Composite See Note 2 (HD only) 1 per 5.3 ft 2 24x36-inch grid, 12-inch from board edges Firestone HD Fasteners with Firestone HD Seam Plates 12- within 6-inch wide laps spaced 142- Laps sealed with 1.5-inch heat weld SC-119. Min. 22 ga., type B, Grade 80 steel or min. 20 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or struct. conc. (Optional) See Note 19 Prelim. attached Firestone HD Plus Fasteners (steel only) or Firestone Concrete Drive ( only) with Firestone HD Plus Seam Plates 6- within 6-inch wide laps spaced 90- Laps sealed with 5-inch heat weld that encapsulates plates Prepared by: Robert Nieminen, PE Appendix 1, Page 18 of 57

19 SC-120. SC-121. SC-122. SC-123. SC-124. SC-125. SC-126. SC-127. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or struct. conc. Min. 22 ga., type B, Grade 80 steel or min. 20 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or struct. conc. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or struct. conc. Min. 22 ga., type B, Grade 80 steel; 6 spans; Traxx/5 screw 6 or struct. conc. Min. 22 ga., type B, Grade 80 steel or min. 20 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or struct. conc. Min. 22 ga., type B, Grade 80 steel or min. 20 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or struct. conc. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or struct. conc. TABLE 2C-2: STEEL OR CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE D-1: INSULATED, MECHANICALLY ATTACHED ROOF COVER (BATTENS) Insulation Roof Cover Type Attach Membrane Fasten Attach Prelim. attached Prelim. attached Prelim. attached Loose Laid Prelim. attached Prelim. attached Prelim. attached Prelim. attached Firestone HD Plus Fasteners (steel only) or Firestone Concrete Drive ( only) with Firestone Polymer Batten Strip Firestone HD Plus Fasteners (steel only) or Firestone Concrete Drive ( only) with Firestone Coiled Metal Batten Strip UltraPly QuickSeam R.M.A. Strips with Firestone HD Fasteners with Firestone Coiled Metal Batten Strip Firestone HD Fasteners with Firestone Coiled Metal Batten Strip Firestone HD Fasteners or Firestone Concrete Drive ( only) with Firestone Batten Strip or Coiled Metal Batten Strip Firestone HD Fasteners or Firestone Concrete Drive ( only) with Firestone Polymer Batten Strips Firestone HD Plus Fasteners (steel only) with Firestone Coiled Metal Batten Strip Firestone HD Fasteners or Firestone Concrete Drive ( only) with Firestone Coiled Metal Batten Strip or Firestone Polymer Batten Strip Fasteners 12- through batten within 6-inch wide laps spaced 114- Laps sealed with 5-inch heat weld that encapsulates batten. Fasteners 12- through batten within 6-inch wide laps spaced 90- Laps sealed with 5-inch heat weld that encapsulates batten. UltraPly QuickSeam R.M.A. Strips are applied over the insulation spaced 120- The batten is centered over each strip and fastened 6- Roof cover adhered to each strip by first priming with QuickPrime at the strip location, then rolling into place with a hand roller. Fasteners 6- through batten within 6-inch wide laps spaced 142- Laps sealed with 5-inch heat weld that encapsulates batten. Fasteners 6- through batten in field of the roof spaced 144- Battens sealed with 5-inch wide cover strip, with 1.5-inch heat weld on each side of the strip or by applying Firestone TPO QuickSeam Flashing atop batten. Fasteners 6- through batten within 6-inch wide laps spaced 114- Laps sealed with 5-inch heat weld that encapsulates batten. Fasteners 6- through batten within 6-inch wide laps spaced 142- Laps sealed with 5-inch heat weld that encapsulates batten. Fasteners 6- through batten within 6-inch wide laps spaced 90- Laps sealed with 5-inch heat weld that encapsulates batten SC-128. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 Prelim. attached Firestone HD Plus Fasteners (steel only) with Firestone Coiled Metal Batten Strip Fasteners 6- through batten within 6-inch wide laps spaced 114- Laps sealed with 5-inch heat weld that encapsulates batten SC-129. Min. 22 ga., type B, Grade 80 steel or min. 20 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or struct. conc. Prelim. attached Firestone HD Fasteners or Firestone Concrete Drive ( only) with Firestone Batten Strip or Coiled Metal Batten Strip or Firestone HD Plus Fasteners (steel only) or Firestone Concrete Drive ( only) with Firestone Polymer Batten Strip Fasteners 6- through batten within 6-inch wide laps spaced 114- Laps sealed with 5-inch heat weld that encapsulates batten Prepared by: Robert Nieminen, PE Appendix 1, Page 19 of 57

20 SC-130. SC-131. SC-132. SC-133. SC-134. SC-135. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or struct. conc. Min. 22 ga., type B, Grade 80 steel; 6 spans; Traxx/5 screw 6 Min. 22 ga., type B, Grade 80 steel or min. 20 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 Min. 22 ga., type B, Grade 80 steel or min. 20 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or struct. conc. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 or struct. conc. Min. 22 ga., type B, Grade 33 steel; 6 spans; Traxx/5 screw 6 TABLE 2C-2: STEEL OR CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE D-1: INSULATED, MECHANICALLY ATTACHED ROOF COVER (BATTENS) Insulation Roof Cover Type Attach Membrane Fasten Attach Min. 0.5-inch Dens, Dens Prime or SECUROCK Gypsum-Fiber Roof Board loose laid over min. 1.5-inch thick, Prelim. attached Loose Laid Prelim. attached Prelim. attached Prelim. attached Prelim. attached Firestone HD Plus Fasteners (steel only) or Firestone Concrete Drive ( only) with Firestone Batten Strip or Coiled Metal Batten Strip Firestone HD Plus Fasteners (steel only) with Firestone ¾ Polymer Batten Strips Firestone HD Fasteners with Firestone Coiled Metal Batten Strip Firestone HD Plus Fasteners (steel only) or Firestone Concrete Drive ( only) with Firestone Batten Strip or Coiled Metal Batten Strip Firestone HD Plus Fasteners (steel only) or Firestone Concrete Drive ( only) with Firestone Coiled Metal Batten Strip Firestone HD Plus Fasteners (steel only) with Firestone Coiled Metal Batten Strip Fasteners 6- through batten within 6-inch wide laps spaced 90- Laps sealed with 5-inch heat weld that encapsulates batten. Fasteners 6- through batten within 6-inch wide laps spaced 68- Laps sealed with 5-inch heat weld that encapsulates battens. Fasteners 6- through batten within 6-inch wide laps spaced 90- Laps sealed with 5-inch heat weld that encapsulates batten. Fasteners 6- through batten within 6-inch wide laps spaced 90- Laps sealed with 5-inch heat weld that encapsulates batten. Fasteners 6- through batten within 6-inch wide laps spaced 54- Laps sealed with 5-inch heat weld that encapsulates batten. Fasteners 6- through batten within 6-inch wide laps spaced 54- Laps sealed with 5-inch heat weld that encapsulates batten SC-136. Min. 22 ga., type B, Grade 80 steel; 6 spans; Traxx/5 screw 6 Loose Laid Firestone HD Plus Fasteners (steel only) with Firestone ¾ Polymer Batten Strips Lap Row: Fasteners 6- through battens within 6- inch wide laps spaced 142- Laps sealed with 5-inch heat weld that encapsulates the batten. Field Row: Fasteners 6- through battens in one intermediate row between laps. Batten strips covered with 5-inch wide strips sealed on both sides with 1.5-inch heat weld Prepared by: Robert Nieminen, PE Appendix 1, Page 20 of 57

21 TABLE 3A-1: CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1A: BONDED INSULATION, BONDED ROOF COVER Type Attach Type Attach ULTRAPLY TPO SYSTEMS C-1 with optional Tapered ISO 95+ Hot Asphalt Min. 0.5-inch Firestone FiberTop Hot Asphalt LVOC-BA * C-2 or Hot Asphalt (Optional) Tapered ISO 95+ Hot asphalt LVOC-BA * C-3 with optional Tapered ISO 95+ Hot Asphalt Min inch Dens, Dens Prime or Hot Asphalt / UP-BA * C-4 with optional Tapered ISO 95+ Hot Asphalt Min inch Dens Prime or SECUROCK Hot Asphalt / LVOC-BA * C-5 or (Optional) Additional layers of base insulation LVOC-BA * C-6 or, 8- (Optional) Additional layers of base insulation, 8- LVOC-BA * C-7, 4- (Optional) Additional layers of base insulation, 4- LVOC-BA * C-8 Min. 1.5-inch (Optional) Additional layers of base insulation / WBBA-S, * C-9 Min. 1.5-inch, 8- (Optional) Additional layers of base insulation, 8- / WBBA-S, * C-10 Min. 1.5-inch, 6- (Optional) Additional layers of base insulation, 6- / WBBA-S, * C-11 Min. 1.5-inch, 6- (Optional) Additional layers of base insulation, 6- LVOC-BA * C-12 Min. 1-inch Min. 1-inch / LVOC-BA * C-13 Min. two layers min inch ISO 95+ Min. 0.5-inch FiberTop C or S / LVOC-BA * C-14 Min inch Dens Prime or SECUROCK LVOC-BA * C-15 Min inch Dens or SECUROCK / UP-BA * Prepared by: Robert Nieminen, PE Appendix 1, Page 21 of 57

22 C-16 C-17 C-18 C-19 C-20 C-21 C-22 C-23 C-24 C-25 C-26 C-27 C-28 C-29 C-30 C-31 C-32 TABLE 3A-1: CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1A: BONDED INSULATION, BONDED ROOF COVER Type Attach Type Attach, 8- Two layers min. 1.5-inch ISO 95+, 8-, 4- Min. two layers min inch ISO 95+ One or more layers, min. 1.5-inch ISO 95+ One or more layers, min. 1.5-inch ISO 95+ Min inch Dens Prime or SECUROCK Min inch Dens Prime or SECUROCK min. 1-inch ISO 95+ or 0.5-inch Tapered ISO 95+; Min inch Dens Prime or Min inch Dens Prime or SECUROCK Min inch Dens Prime or SECUROCK, 8-, 8- LVOC-BA * / UP-BA * / WBBA-S *, 4- LVOC-BA * / LVOC-BA * Min. 0.5-inch ISOGARD HD / WBBA-S, * Min. 0.5-inch ISOGARD HD Min. 0.5-inch ISOGARD HD N/A 3M CR-20 (Optional) Additional layers base insulation 3M CR-20 3M CR-20 3M CR-20 or Min inch Dens or SECUROCK Min inch Dens Prime or SECUROCK LVOC-BA- LVOC-BA-, WBBA-S, LVOC-BA * * * 3M CR-20 / UP-BA * 3M CR-20 (Optional) Additional layers of base insulation LVOC-BA- LVOC-BA- Min. 1.5-inch (Optional) Additional layers of base insulation / WBBA-S, * Min. 1.5-inch, 6- (Optional) Additional layers of base insulation, 6-inch * * / WBBA-S, * (Optional) Additional layers of base insulation / UP-BA * Min. 1.5-inch, 6- (Optional) Additional layers of base insulation, 6-inch LVOC-BA- Min. 1-inch Min. 1-inch / LVOC-BA * * Prepared by: Robert Nieminen, PE Appendix 1, Page 22 of 57

23 C-33 C-34 C-35 C-36 C-37 C-38 C-39 C-40 C-41 C-42 TABLE 3A-1: CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1A: BONDED INSULATION, BONDED ROOF COVER Type Attach Type Attach Min. two layers min inch ISO 95+ Min. two layers min inch ISO 95+ One or more layers, min. 1.5-inch ISO 95+ One or more layers, min. 1.5-inch ISO 95+ Min. 0.5-inch FiberTop C or S / LVOC-BA * Min inch Dens, Dens Prime or Min inch Dens Prime or SECUROCK min. 1-inch ISO 95+ or 0.5-inch Tapered ISO 95+; Min inch Dens Prime or Min inch Dens Prime or SECUROCK / UP-BA * / LVOC-BA * / WBBA-S * / LVOC-BA * Min. 0.5-inch ISOGARD HD / WBBA-S, * Min. 0.5-inch ISOGARD HD Min. 1.5-inch, 6- Min. 0.5-inch ISOGARD HD or min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 19/32-inch plywood Min. 0.5-inch ISOGARD HD N/A, 6-inch LVOC-BA- LVOC-BA- LVOC-BA-, WBBA-S, WBBA- P LVOC-BA-, WBBA-S, * * * * C-43 Min. 1.5-inch, 6- (Optional) Additional layers of base insulation, 6-inch / WBBA-S, * C-44 C-45 C-46 C-47 C-48 Min. 1.5-inch, 6- (Optional) Additional layers of base insulation, 6-inch LVOC-BA- Min. 1-inch Min. 1-inch / LVOC-BA * Min. two layers min inch ISO 95+ Min. two layers min inch ISO 95+ Min. 0.5-inch FiberTop C or S / LVOC-BA * min. 1-inch ISO 95+ or 0.5-inch Tapered ISO 95+; Min inch Dens Prime or Min inch Dens Prime or SECUROCK Prepared by: Robert Nieminen, PE Appendix 1, Page 23 of * / WBBA-S * / LVOC-BA *

24 C-49 C-50 C-51 C-52 C-53 C-54 C-55 C-56 C-57 C-58 C-59 C-60 C-61 C-62 C-63 C-64 TABLE 3A-1: CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1A: BONDED INSULATION, BONDED ROOF COVER Type Attach Type Attach One or more layers, min. 1.5-inch ISO 95+ Min. 0.5-inch ISOGARD HD / WBBA-S, * Min. 0.5-inch ISOGARD HD, 4- N/A / WBBA-S, * Min. 0.5-inch ISOGARD HD, 4- N/A One or more layers, min. 1.5-inch ISO 95+ Min. 0.5-inch ISOGARD HD Min. 1.5-inch, 6- Min. 0.5-inch ISOGARD HD, 6-inch LVOC-BA- LVOC-BA- LVOC-BA- Min. 0.5-inch ISOGARD HD, 4- N/A / LVOC-BA * Min. 1-inch (Optional) Additional layers of base insulation and/or min. 0.5-inch Tapered ISO 95+ (Optional) Additional layers of base insulation and/or min. 0.5-inch Tapered (Optional) Additional layers of base insulation and/or min. 0.5-inch Tapered ISO 95+ or Tapered Min. 1.5-inch, 6- (Optional) Additional layers of base insulation * * * / WBBA-S, / WBBA-S, *, 6-inch LVOC-BA- LVOC-BA- Min. 1-inch Min. 1-inch / LVOC-BA * min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 0.5-inch ISOGARD HD min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 0.5-inch ISOGARD HD min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 0.5-inch FiberTop C or S min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 0.5-inch FiberTop C or S min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 0.5-inch FiberTop C or S * * / WBBA-S, * LVOC-BA * LVOC-BA -60.0* / WBBA-S, * / LVOC-BA * Prepared by: Robert Nieminen, PE Appendix 1, Page 24 of 57

25 C-65 C-66 C-67 C-68 C-69 TABLE 3A-1: CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1A: BONDED INSULATION, BONDED ROOF COVER Type Attach Type Attach min. 0.5-inch Tapered ISO 95+ or Tapered ; Min inch Dens Prime or min. 1-inch ISO 95+ or 0.5-inch Tapered ISO 95+; Min inch Dens Prime or min. 0.5-inch Tapered ISO 95+ or Tapered ; Min inch Dens Prime or min. 0.5-inch Tapered ISO 95+ or Tapered ; Min inch Dens Prime or min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 19/32-inch plywood / WBBA-S, * / WBBA-S * LVOC-BA * / LVOC-BA * LVOC-BA-, WBBA-S, WBBA- P * ULTRAPLY TPO XR SYSTEMS IN XR BONDING ADHESIVE C-70 C-71 C-72 C-73 C-74 C-75 Min inch Dens Prime or SECUROCK One or two layers min inch ISO 95+ Hot Asphalt N/A XR / XR-BA * Hot Asphalt ; I.S.O. Stick ; I.S.O. Stick Min inch Dens Prime or SECUROCK (Optional) Additional layer of base insulation or min. 0.5-inch Tapered ISO 95+ or min. 0.5-inch Tapered ISO 95+ or followed by min. 0.5-inch ISOGARD HD min. 0.5-inch Tapered ISO 95+ or followed by Min inch Dens Prime or min. 0.5-inch Tapered ISO 95+ or followed by Min inch Dens Prime or Hot Asphalt XR / XR-BA * ; ; XR / XR-BA * XR / XR-BA * XR / XR-BA * XR / XR-BA * Prepared by: Robert Nieminen, PE Appendix 1, Page 25 of 57

26 C-76 C-77 ULTRAPLY TPO XR SYSTEMS IN HOT ASPHALT C-78 C-79 C-80 C-81 C-82 C-83 C-84 C-85 (Optional) (Optional) TABLE 3A-1: CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1A: BONDED INSULATION, BONDED ROOF COVER Type Attach Type Attach Min inch Dens Prime or SECUROCK min. 0.5-inch Tapered ISO 95+ or Tapered ; Min inch Dens Prime or min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 0.5-inch FiberTop C or S Prepared by: Robert Nieminen, PE Appendix 1, Page 26 of 57 XR / XR-BA * XR / XR-BA Hot Asphalt N/A XR / Hot Asphalt * Hot asphalt (Optional) Additional layers of base insulation Hot asphalt XR / Hot Asphalt * Hot Asphalt N/A XR / Hot Asphalt * Hot Asphalt N/A XR / Hot Asphalt * (Optional) (Optional) ULTRAPLY TPO XR SYSTEMS IN I.S.O. SPRAY S OR XR STICK: C-86 C-87 C-88 Two layers min. 1.5-inch ISO 95+ Hot Asphalt Hot Asphalt ; I.S.O. Stick ; I.S.O. Stick ; I.S.O. Stick Min inch Dens Prime or SECUROCK Min inch Dens Prime or SECUROCK min. 0.5-inch Tapered ISO 95+ or followed by Min inch Dens Prime or min. 0.5-inch Tapered ISO 95+ or followed by Min inch Dens Prime or (Optional) Additional layer of base insulation or min. 0.5-inch Tapered ISO 95+ or (Optional) Additional layer of base insulation or min. 0.5-inch Tapered ISO 95+ or min. 0.5-inch Tapered ISO 95+ or followed by min. 0.5-inch ISOGARD HD Hot Asphalt XR / Hot Asphalt * Hot Asphalt XR / Hot Asphalt * XR / Hot Asphalt * XR / Hot Asphalt * ; ; ; XR / I.S.O Spray S, XR Stick, 12- XR / I.S.O Spray S, XR Stick, 4- (full coverage) XR / I.S.O Spray S, XR Stick, *

27 TABLE 3A-1: CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1A: BONDED INSULATION, BONDED ROOF COVER C-89 C-90 C-91 C-92 C-93 C-94 C-95 Type Attach Type Attach Min. 1-inch Insulfoam EPS (2 pcf) ; I.S.O. Stick ; I.S.O. Stick ; I.S.O. Stick ; I.S.O. Stick ; I.S.O. Stick ; I.S.O. Stick min. 0.5-inch Tapered ISO 95+ or followed by min. 0.5-inch ISOGARD HD min. 0.5-inch Tapered ISO 95+ or followed by min. 0.5-inch ISOGARD HD min. 0.5-inch Tapered ISO 95+ or followed by Min inch Dens Prime or min. 0.5-inch Tapered ISO 95+ or followed by Min inch Dens Prime or min. 0.5-inch Tapered ISO 95+ or followed by Min inch Dens Prime or min. 0.5-inch Tapered ISO 95+ or followed by min. 19/32-inch plywood Min inch Dens Prime or SECUROCK ; ; ; ; ; ; XR / I.S.O Spray S, XR Stick, 6- XR / I.S.O Spray S, XR Stick, 4- (full coverage) XR / I.S.O Spray S, XR Stick, 12- XR / I.S.O Spray S, XR Stick, 6- XR / I.S.O Spray S, XR Stick, 4- (full coverage) XR / I.S.O Spray S, XR Stick, 12- XR /, XR Stick, * -60.0* * Prepared by: Robert Nieminen, PE Appendix 1, Page 27 of 57

28 TABLE 3A-2: CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1B: BONDED TEMP ROOF, BONDED INSULATION, BONDED ROOF COVER Sys. Vapor Barrier / Temporary Roof Type Attach Type Attach ULTRAPLY TPO SYSTEMS: C-96 MB Base M, adhered in Min inch Dens, Dens Prime or / UP-BA * C-97 MB Base M, adhered in Min inch Dens Prime or SECUROCK / LVOC-BA * C-98 SBS Poly Torch or SBS Glass Torch Base, torch applied Min inch Dens, Dens Prime or / UP-BA * C-99 SBS Poly Torch or SBS Glass Torch Base, torch applied Min inch Dens Prime or SECUROCK / LVOC-BA * C-100, 6- (Optional) Additional layers of base insulation and/or min. 0.5-inch Tapered ISO 95+, 6- / WBBA-S, WBBA- P C-101 Min. 1-inch, 6- (Optional) Additional layers of base insulation and/or min. 0.5-inch Tapered, 6- / WBBA-S, WBBA- P * C-102 or, 6- (Optional) Additional layers of base insulation and/or min. 0.5-inch Tapered ISO 95+ or Tapered, 6- LVOC-BA * C-103 or, 6- min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 0.5-inch ISOGARD HD, 6- / WBBA-S, WBBA- P * C-104 or, 6- min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 0.5-inch ISOGARD HD, 6- LVOC-BA * C-105 or, 6- min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 0.5-inch FiberTop C or S, 6- LVOC-BA -60.0* C-106 or, 6- min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 0.5-inch FiberTop C or S, 6- / WBBA-S, WBBA- P * C-107 or, 6- min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 0.5-inch FiberTop C or S, 6- / LVOC-BA * Prepared by: Robert Nieminen, PE Appendix 1, Page 28 of 57

29 TABLE 3A-2: CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1B: BONDED TEMP ROOF, BONDED INSULATION, BONDED ROOF COVER Sys. Vapor Barrier / Temporary Roof Type Attach Type Attach C-108 or, 6- min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 0.5-inch Dens Prime or, 6- / WBBA-S, WBBA- P * C-109 or, 6- min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 0.5-inch Dens Prime or, 6- LVOC-BA * C-110 or, 6- min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 0.5-inch Dens Prime or, 6- / LVOC-BA * C-111 or, 6- min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 19/32-inch plywood, 6- LVOC-BA-, WBBA-S, * C-112 V-Force SB V-Force Vapor Barrier Membrane (Optional) Additional layers of base insulation / WBBA-S, WBBA- P C-113 V-Force WB V-Force Vapor Barrier Membrane (Optional) Additional layers of base insulation LVOC-BA C-114 V-Force SB V-Force Vapor Barrier Membrane N/A LVOC-BA * C-115 V-Force SB V-Force Vapor Barrier Membrane (Optional) Additional layers of base insulation / WBBA-S, WBBA- P C-116 V-Force WB V-Force Vapor Barrier Membrane (Optional) Additional layers of base insulation LVOC-BA C-117 V-Force SB V-Force Vapor Barrier Membrane (Optional) Additional layers of base insulation LVOC-BA * C-118 V-Force SB V-Force Vapor Barrier Membrane N/A LVOC-BA * C-119 V-Force SB V-Force Vapor Barrier Membrane min. 0.5-inch Tapered ISO 95+ ; Min. 0.5-inch ISOGARD HD / WBBA-S, WBBA- P * C-120 V-Force SB V-Force Vapor Barrier Membrane min. 0.5-inch Tapered ISO 95+ ; Min. 0.5-inch ISOGARD HD LVOC-BA * Prepared by: Robert Nieminen, PE Appendix 1, Page 29 of 57

30 TABLE 3A-2: CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1B: BONDED TEMP ROOF, BONDED INSULATION, BONDED ROOF COVER Sys. Vapor Barrier / Temporary Roof Type Attach Type Attach C-121 V-Force SB V-Force Vapor Barrier Membrane min. 0.5-inch Tapered ISO 95+ ; Min. 0.5-inch FiberTop C or S LVOC-BA -60.0* C-122 V-Force SB V-Force Vapor Barrier Membrane min. 0.5-inch Tapered ISO 95+ ; Min. 0.5-inch FiberTop C or S / WBBA-S, WBBA- P * C-123 V-Force SB V-Force Vapor Barrier Membrane min. 0.5-inch Tapered ISO 95+ ; Min. 0.5-inch FiberTop C or S / LVOC-BA * C-124 V-Force SB V-Force Vapor Barrier Membrane min. 0.5-inch Tapered ISO 95+ ; Min inch Dens Prime or SECUROCK Gypsum-Fiber Roof Board / WBBA-S, WBBA- P * C-125 V-Force SB V-Force Vapor Barrier Membrane min. 0.5-inch Tapered ISO 95+ ; Min inch Dens Prime or SECUROCK Gypsum-Fiber Roof Board LVOC-BA * C-126 V-Force SB V-Force Vapor Barrier Membrane min. 0.5-inch Tapered ISO 95+ ; Min inch Dens Prime or SECUROCK Gypsum-Fiber Roof Board / LVOC-BA * C-127 V-Force SB V-Force Vapor Barrier Membrane min. 0.5-inch Tapered ISO 95+ ; Min. 19/32-inch plywood LVOC-BA-, WBBA-S, * ULTRAPLY TPO XR SYSTEMS: C-128 or min. 0.5-inch Tapered ISO 95+ or followed by Min inch Dens Prime or XR / Hot Asphalt * C-129 or min. 0.5-inch Tapered ISO 95+ or followed by Min inch Dens Prime or XR / Hot Asphalt -60.0* C-130 or, 6- min. 0.5-inch Tapered ISO 95+ or followed by Min inch Dens Prime or, 6- XR / Hot Asphalt * Prepared by: Robert Nieminen, PE Appendix 1, Page 30 of 57

31 TABLE 3A-2: CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1B: BONDED TEMP ROOF, BONDED INSULATION, BONDED ROOF COVER Sys. Vapor Barrier / Temporary Roof Type Attach Type Attach C-131 or min. 0.5-inch Tapered ISO 95+ or followed by Min inch Dens Prime or XR / Hot Asphalt * C-132 or (Optional) Additional layer of base insulation or min. 0.5-inch Tapered ISO 95+ or XR / XR-BA * C-133 or min. 0.5-inch Tapered ISO 95+ or followed by min. 0.5-inch ISOGARD HD XR / XR-BA * C-134 or min. 0.5-inch Tapered ISO 95+ or followed by Min inch Dens Prime or XR / XR-BA * C-135 or (Optional) Additional layer of base insulation or min. 0.5-inch Tapered ISO 95+ or XR / XR-BA -60.0* C-136 or, 6- (Optional) Additional layer of base insulation or min. 0.5-inch Tapered ISO 95+ or, 6- XR / XR-BA * C-137 or min. 0.5-inch Tapered ISO 95+ or followed by min. 0.5-inch ISOGARD HD XR / XR-BA -60.0* C-138 or, 6- min. 0.5-inch Tapered ISO 95+ or followed by min. 0.5-inch ISOGARD HD, 6- XR / XR-BA * C-139 or min. 0.5-inch Tapered ISO 95+ or followed by Min inch Dens Prime or XR / XR-BA -60.0* C-140 or, 6- min. 0.5-inch Tapered ISO 95+ or followed by Min inch Dens Prime or, 6- XR / XR-BA * C-141 or (Optional) Additional layer of base insulation or min. 0.5-inch Tapered ISO 95+ or XR / XR-BA * C-142 or min. 0.5-inch Tapered ISO 95+ or followed by min. 0.5-inch ISOGARD HD XR / XR-BA * Prepared by: Robert Nieminen, PE Appendix 1, Page 31 of 57

32 TABLE 3A-2: CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1B: BONDED TEMP ROOF, BONDED INSULATION, BONDED ROOF COVER Sys. Vapor Barrier / Temporary Roof Type Attach Type Attach C-143 or min. 0.5-inch Tapered ISO 95+ or followed by Min inch Dens Prime or XR / XR-BA * C-144 or, 6- min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 0.5-inch FiberTop C or S, 6- XR / XR-BA C-145 or, 6- min. 0.5-inch Tapered ISO 95+ or Tapered ; Min inch Dens Prime or, 6- XR / XR-BA * C-146 V-Force SB V-Force Vapor Barrier Membrane N/A XR / XR-BA * C-147 V-Force SB V-Force Vapor Barrier Membrane min. 0.5-inch Tapered ISO 95+; Min. 0.5-inch FiberTop C or S XR / XR-BA C-148 V-Force SB V-Force Vapor Barrier Membrane min. 0.5-inch Tapered ISO 95+; Min inch Dens Prime or SECUROCK Gypsum-Fiber Roof Board XR / XR-BA * C-149 Firestone APP 80 Glass Base, torched or (Optional) Additional layer of base insulation or min. 0.5-inch Tapered ISO 95+ or XR / XR-BA * C-150 or (Optional) Additional layer of base insulation or min. 0.5-inch Tapered ISO 95+ or XR / I.S.O Spray S, XR Stick, * C-151 or (Optional) Additional layer of base insulation or min. 0.5-inch Tapered ISO 95+ or XR / I.S.O Spray S, XR Stick, 4- (full coverage) C-152 or min. 0.5-inch Tapered ISO 95+ or followed by min. 0.5-inch ISOGARD HD XR / I.S.O Spray S, XR Stick, 12- C-153 or min. 0.5-inch Tapered ISO 95+ or followed by min. 0.5-inch ISOGARD HD XR / I.S.O Spray S, XR Stick, * C-154 or min. 0.5-inch Tapered ISO 95+ or followed by min. 0.5-inch ISOGARD HD XR / I.S.O Spray S, XR Stick, 4- (full coverage) Prepared by: Robert Nieminen, PE Appendix 1, Page 32 of 57

33 TABLE 3A-2: CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1B: BONDED TEMP ROOF, BONDED INSULATION, BONDED ROOF COVER Sys. Vapor Barrier / Temporary Roof Type Attach Type Attach C-155 or min. 0.5-inch Tapered ISO 95+ or followed by Min inch Dens Prime or XR / I.S.O Spray S, XR Stick, 12- C-156 or min. 0.5-inch Tapered ISO 95+ or followed by Min inch Dens Prime or XR / I.S.O Spray S, XR Stick, * C-157 or min. 0.5-inch Tapered ISO 95+ or followed by Min inch Dens Prime or XR / I.S.O Spray S, XR Stick, 4- (full coverage) C-158 or min. 0.5-inch Tapered ISO 95+ or followed by min. 19/32-inch plywood XR / I.S.O Spray S, XR Stick, 12- C-159 Firestone APP 80 Glass Base, torched or (Optional) Additional layer of base insulation or min. 0.5-inch Tapered ISO 95+ or XR / I.S.O Spray S, XR Stick, * C-160 Firestone APP 80 Glass Base, torched or (Optional) Additional layer of base insulation or min. 0.5-inch Tapered ISO 95+ or XR / I.S.O Spray S, XR Stick, 4- (full coverage) C-161 or (Optional) Additional layer of base insulation or min. 0.5-inch Tapered ISO 95+ or XR / I.S.O Spray S, XR Stick, * C-162 or, 6- (Optional) Additional layer of base insulation or min. 0.5-inch Tapered ISO 95+ or, 6- XR / I.S.O Spray S, XR Stick, * C-163 or, 6- (Optional) Additional layer of base insulation or min. 0.5-inch Tapered ISO 95+ or, 6- XR / I.S.O Spray S, XR Stick, 4- (full coverage) * C-164 or min. 0.5-inch Tapered ISO 95+ or followed by min. 0.5-inch ISOGARD HD XR / I.S.O Spray S, XR Stick, 12- C-165 or min. 0.5-inch Tapered ISO 95+ or followed by min. 0.5-inch ISOGARD HD XR / I.S.O Spray S, XR Stick, * C-166 or, 6- min. 0.5-inch Tapered ISO 95+ or followed by min. 0.5-inch ISOGARD HD, 6- XR / I.S.O Spray S, XR Stick, * Prepared by: Robert Nieminen, PE Appendix 1, Page 33 of 57

34 TABLE 3A-2: CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1B: BONDED TEMP ROOF, BONDED INSULATION, BONDED ROOF COVER Sys. Vapor Barrier / Temporary Roof Type Attach Type Attach C-167 or, 6- min. 0.5-inch Tapered ISO 95+ or followed by min. 0.5-inch ISOGARD HD, 6- XR / I.S.O Spray S, XR Stick, 4- (full coverage) C-168 or min. 0.5-inch Tapered ISO 95+ or followed by Min inch Dens Prime or XR / I.S.O Spray S, XR Stick, 12- C-169 or min. 0.5-inch Tapered ISO 95+ or followed by Min inch Dens Prime or XR / I.S.O Spray S, XR Stick, * C-170 or, 6- min. 0.5-inch Tapered ISO 95+ or followed by Min inch Dens Prime or, 6- XR / I.S.O Spray S, XR Stick, 4- (full coverage) C-171 or min. 0.5-inch Tapered ISO 95+ or followed by min. 19/32-inch plywood XR / I.S.O Spray S, XR Stick, 12- C-172 or (Optional) Additional layer of base insulation or min. 0.5-inch Tapered ISO 95+ or XR / I.S.O Spray S, XR Stick, * C-173 or (Optional) Additional layer of base insulation or min. 0.5-inch Tapered ISO 95+ or XR / I.S.O Spray S, XR Stick, 4- (full coverage) C-174 or min. 0.5-inch Tapered ISO 95+ or followed by min. 0.5-inch ISOGARD HD XR / I.S.O Spray S, XR Stick, 12- C-175 or min. 0.5-inch Tapered ISO 95+ or followed by min. 0.5-inch ISOGARD HD XR / I.S.O Spray S, XR Stick, * C-176 or min. 0.5-inch Tapered ISO 95+ or followed by min. 0.5-inch ISOGARD HD XR / I.S.O Spray S, XR Stick, 4- (full coverage) C-177 or min. 0.5-inch Tapered ISO 95+ or followed by Min inch Dens Prime or XR / I.S.O Spray S, XR Stick, 12- Prepared by: Robert Nieminen, PE Appendix 1, Page 34 of 57

35 TABLE 3A-2: CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1B: BONDED TEMP ROOF, BONDED INSULATION, BONDED ROOF COVER Sys. Vapor Barrier / Temporary Roof Type Attach Type Attach C-178 or min. 0.5-inch Tapered ISO 95+ or followed by Min inch Dens Prime or XR / I.S.O Spray S, XR Stick, * C-179 or min. 0.5-inch Tapered ISO 95+ or followed by Min inch Dens Prime or XR / I.S.O Spray S, XR Stick, 4- (full coverage) C-180 or min. 0.5-inch Tapered ISO 95+ or followed by min. 19/32-inch plywood XR / I.S.O Spray S, XR Stick, 12- TABLE 3B: CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE F: NON-INSULATED, BONDED ROOF COVER Roof Cover Base Ply Application Top Ply Application C-181 N/A XR XR Stick, * C-182 N/A XR XR-BA * C-183 N/A XR XR Stick, * C-184 N/A XR XR-BA * C-185 C-186 One or two plies Firestone Type IV (4) M or Type VI (6) M or one ply of MB Base, SBS Base, SBS PolyBase or SBS Premium Base One or two plies Firestone Type IV (4) M or Type VI (6) M or one ply of MB Base, SBS Base, SBS PolyBase or SBS Premium Base Hot asphalt XR, * Hot asphalt XR XR Stick, * C-187 N/A XR Hot asphalt * C-188 N/A XR, * C-189 N/A XR Hot asphalt * Prepared by: Robert Nieminen, PE Appendix 1, Page 35 of 57

36 TABLE 4A: LIGHTWEIGHT CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1A: BONDED INSULATION, BONDED ROOF COVER Coverboard Struct LWC Type Attach Type Attach LWC-1 (Optional) Additional layer of base LVOC-BA-, LVOC- BA * LWC-2 Min. 1-inch (Optional) Additional layer of base insulation or min. 0.5-inch Tapered LVOC-BA-, LVOC- BA * LWC-3 (Optional) Min inch Tapered ISO 95+ or Tapered Min. 2-inch ISOGARD HD Composite LVOC-BA-, LVOC- BA * LWC-4 or Optional additional layers of base or followed by min. 0.5-inch ISOGARD HD LVOC-BA-, LVOC- BA * LWC-5 or Optional additional layers of base or followed by Min inch Dens Prime or SECUROCK Gypsum- Fiber Roof Board LVOC-BA-, LVOC- BA * LWC-6 or Optional additional layers of base or followed by min. 19/32-inch plywood LVOC-BA-, LVOC- BA * LWC-7 (Optional) Additional layer of base / WBBA-S, LWC-8 Min. 1-inch (Optional) Additional layer of base insulation or min. 0.5-inch Tapered / WBBA-S, * LWC-9 (Optional) Min inch Tapered ISO 95+ or Tapered Min. 2-inch ISOGARD HD Composite / WBBA-S, * Prepared by: Robert Nieminen, PE Appendix 1, Page 36 of 57

37 TABLE 4A: LIGHTWEIGHT CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1A: BONDED INSULATION, BONDED ROOF COVER LWC-10 LWC-11 LWC-12 LWC-13 LWC-14 LWC-15 LWC-16 LWC-17 LWC-18 LWC-19 Coverboard Struct LWC Type Attach Type Attach Min. 200 psi, min. 2-inch thick Celcore, Elastizell, Mearlcrete or Insulcel cellular LWIC. Min. 200 psi, min. 2-inch thick Celcore, Elastizell, Mearlcrete or Insulcel cellular LWIC. or or Min. 1-inch (Optional) Min inch Tapered ISO 95+ or Tapered or or or Optional additional layers of base or followed by min. 0.5-inch ISOGARD HD Optional additional layers of base or followed by Min inch Dens Prime or SECUROCK Gypsum- Fiber Roof Board (Optional) Additional layer of base (Optional) Additional layer of base insulation or min. 0.5-inch Tapered (Optional) Additional layers of base insulation Min. 2-inch ISOGARD HD Composite Optional additional layers of base or followed by min. 0.5-inch ISOGARD HD Optional additional layers of base or followed by Min inch Dens Prime or SECUROCK Gypsum- Fiber Roof Board Min inch Dens Prime or Optional additional layers of base or followed by min. 19/32-inch plywood / WBBA-S, / WBBA-S, LVOC-BA-, LVOC- BA LVOC-BA-, LVOC- BA * * * * / UP-BA * LVOC-BA-, LVOC- BA LVOC-BA-, LVOC- BA LVOC-BA-, LVOC- BA * * * / UP-BA * LVOC-BA-, LVOC- BA * Prepared by: Robert Nieminen, PE Appendix 1, Page 37 of 57

38 LWC-20 LWC-21 LWC-22 LWC-23 LWC-24 LWC-25 LWC-26 LWC-27 LWC-28 TABLE 4A: LIGHTWEIGHT CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1A: BONDED INSULATION, BONDED ROOF COVER Coverboard Struct LWC Type Attach Type Attach Min. 1-inch (Optional) Min inch Tapered ISO 95+ or Tapered or or Min. 1-inch (Optional) Min inch Tapered ISO 95+ or Tapered or (Optional) Additional layer of base (Optional) Additional layer of base insulation or min. 0.5-inch Tapered Min. 2-inch ISOGARD HD Composite Optional additional layers of base or followed by min. 0.5-inch ISOGARD HD Optional additional layers of base or followed by Min inch Dens Prime or SECUROCK Gypsum- Fiber Roof Board (Optional) Additional layer of base (Optional) Additional layer of base insulation or min. 0.5-inch Tapered Min. 2-inch ISOGARD HD Composite Optional additional layers of base or followed by min. 0.5-inch ISOGARD HD / WBBA-S, / WBBA-S, / WBBA-S, / WBBA-S, / WBBA-S, * * * * XR / XR-BA * XR / XR-BA * XR / XR-BA * XR / XR-BA * Prepared by: Robert Nieminen, PE Appendix 1, Page 38 of 57

39 LWC-29 LWC-30 LWC-31 LWC-32 LWC-33 LWC-34 LWC-35 LWC-36 LWC-37 TABLE 4A: LIGHTWEIGHT CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1A: BONDED INSULATION, BONDED ROOF COVER Coverboard Struct LWC Type Attach Type Attach or Min. 1-inch (Optional) Min inch Tapered ISO 95+ or Tapered or or or (Optional) Min inch Tapered ISO 95+ or Tapered or Optional additional layers of base or followed by Min inch Dens Prime or SECUROCK Gypsum- Fiber Roof Board (Optional) Additional layer of base (Optional) Additional layer of base insulation or min. 0.5-inch Tapered Min. 2-inch ISOGARD HD Composite Optional additional layers of base or followed by min. 0.5-inch ISOGARD HD Optional additional layers of base or followed by Min inch Dens Prime or SECUROCK Gypsum- Fiber Roof Board Optional additional layers of base or followed by min. 19/32-inch plywood Min. 2-inch ISOGARD HD Composite Optional additional layers of base or followed by min. 0.5-inch ISOGARD HD XR / XR-BA * XR / I.S.O Spray S, XR Stick, 12- XR / I.S.O Spray S, XR Stick, 12- XR / I.S.O Spray S, XR Stick, 12- XR / I.S.O Spray S, XR Stick, 12- XR / I.S.O Spray S, XR Stick, 12- XR / I.S.O Spray S, XR Stick, 12- XR / I.S.O Spray S, XR Stick, 6-inch XR / I.S.O Spray S, XR Stick, 6-inch * * -82.5* -82.5* Prepared by: Robert Nieminen, PE Appendix 1, Page 39 of 57

40 TABLE 4A: LIGHTWEIGHT CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1A: BONDED INSULATION, BONDED ROOF COVER LWC-38 LWC-39 LWC-40 LWC-41 LWC-42 LWC-43 LWC-44 LWC-45 LWC-46 Coverboard Struct LWC Type Attach Type Attach or Min. 1-inch (Optional) Min inch Tapered ISO 95+ or Tapered or or Min. 1-inch (Optional) Min inch Tapered ISO 95+ or Tapered Optional additional layers of base or followed by Min inch Dens Prime or SECUROCK Gypsum- Fiber Roof Board (Optional) Additional layer of base (Optional) Additional layer of base insulation or min. 0.5-inch Tapered Min. 2-inch ISOGARD HD Composite Optional additional layers of base or followed by min. 0.5-inch ISOGARD HD Optional additional layers of base or followed by Min inch Dens Prime or SECUROCK Gypsum- Fiber Roof Board (Optional) Additional layer of base (Optional) Additional layer of base insulation or min. 0.5-inch Tapered XR / I.S.O Spray S, XR Stick, 6-inch XR / I.S.O Spray S, XR Stick, 4-inch (full coverage) XR / I.S.O Spray S, XR Stick, 4-inch (full coverage) XR / I.S.O Spray S, XR Stick, 4-inch (full coverage) XR / I.S.O Spray S, XR Stick, 4-inch (full coverage) XR / I.S.O Spray S, XR Stick, 4-inch (full coverage) -60.0* XR / XR-BA * XR / XR-BA * Min. 2-inch ISOGARD HD Composite XR / XR-BA * Prepared by: Robert Nieminen, PE Appendix 1, Page 40 of 57

41 TABLE 4A: LIGHTWEIGHT CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1A: BONDED INSULATION, BONDED ROOF COVER LWC-47 LWC-48 LWC-49 LWC-50 LWC-51 LWC-52 LWC-53 LWC-54 LWC-55 Coverboard Struct LWC Type Attach Type Attach or or Min. 1-inch (Optional) Min inch Tapered ISO 95+ or Tapered or or or (Optional) Min inch Tapered ISO 95+ or Tapered Optional additional layers of base or followed by min. 0.5-inch ISOGARD HD Optional additional layers of base or followed by Min inch Dens Prime or SECUROCK Gypsum- Fiber Roof Board (Optional) Additional layer of base (Optional) Additional layer of base insulation or min. 0.5-inch Tapered XR / XR-BA * XR / XR-BA * Min. 2-inch ISOGARD HD Composite Optional additional layers of base or followed by min. 0.5-inch ISOGARD HD Optional additional layers of base or followed by Min inch Dens Prime or SECUROCK Gypsum- Fiber Roof Board Optional additional layers of base or followed by min. 19/32-inch plywood Min. 2-inch ISOGARD HD Composite XR / I.S.O Spray S, XR Stick, 12- XR / I.S.O Spray S, XR Stick, 12- XR / I.S.O Spray S, XR Stick, 12- XR / I.S.O Spray S, XR Stick, 12- XR / I.S.O Spray S, XR Stick, 12- XR / I.S.O Spray S, XR Stick, 12- XR / I.S.O Spray S, XR Stick, 6-inch * * -82.5* Prepared by: Robert Nieminen, PE Appendix 1, Page 41 of 57

42 TABLE 4A: LIGHTWEIGHT CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1A: BONDED INSULATION, BONDED ROOF COVER LWC-56 LWC-57 LWC-58 LWC-59 LWC-60 LWC-61 LWC-62 LWC-63 LWC-64 LWC-65 LWC-66 Coverboard Struct LWC Type Attach Type Attach Min. 200 psi, min. 2-inch thick Elastizell cellular LWIC. Min. 200 psi, min. 2-inch thick Celcore cellular LWIC. Min. 200 psi, min. 2-inch thick Mearlcrete cellular LWIC. Min. 200 psi, min. 2-inch thick Elastizell cellular LWIC. or or Min. 1-inch (Optional) Min inch Tapered ISO 95+ or Tapered or or Optional additional layers of base or followed by min. 0.5-inch ISOGARD HD Optional additional layers of base or followed by Min inch Dens Prime or SECUROCK Gypsum- Fiber Roof Board (Optional) Additional layer of base (Optional) Additional layer of base insulation or min. 0.5-inch Tapered Min. 2-inch ISOGARD HD Composite Optional additional layers of base or followed by min. 0.5-inch ISOGARD HD Optional additional layers of base or followed by Min inch Dens Prime or SECUROCK Gypsum- Fiber Roof Board XR / I.S.O Spray S, XR Stick, 6-inch XR / I.S.O Spray S, XR Stick, 6-inch XR / I.S.O Spray S, XR Stick, 4-inch (full coverage) XR / I.S.O Spray S, XR Stick, 4-inch (full coverage) XR / I.S.O Spray S, XR Stick, 4-inch (full coverage) XR / I.S.O Spray S, XR Stick, 4-inch (full coverage) XR / I.S.O Spray S, XR Stick, 4-inch (full coverage) -82.5* -60.0* 3M CR-20 (Optional) Additional layers base insulation 3M CR-20 / UP-BA * 3M CR-20 (Optional) Additional layers base insulation 3M CR-20 / UP-BA * 3M CR-20 (Optional) Additional layers base insulation 3M CR-20 / UP-BA * 3M CR-20 Min inch Dens or SECUROCK 3M CR-20 / UP-BA * Prepared by: Robert Nieminen, PE Appendix 1, Page 42 of 57

43 TABLE 4A: LIGHTWEIGHT CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1A: BONDED INSULATION, BONDED ROOF COVER LWC-67 LWC-68 LWC-69 LWC-70 Coverboard Struct LWC Type Attach Type Attach Min. 200 psi, min. 2-inch thick Celcore or Mearlcrete cellular LWIC. Min. 200 psi, min. 2-inch thick Elastizell cellular LWIC. Min. 200 psi, min. 2-inch thick Celcore cellular LWIC. Min. 200 psi, min. 2-inch thick Mearlcrete cellular LWIC. 3M CR-20 3M CR-20 3M CR-20 3M CR-20 Min inch Dens or SECUROCK Min inch Dens Prime or Min inch Dens Prime or Min inch Dens Prime or 3M CR-20 / UP-BA * 3M CR-20 / UP-BA * 3M CR-20 / UP-BA * 3M CR-20 / UP-BA * LWC-71 Min. 22 ga., type BV (0.5%), 60 ksi steel; 5 spans, 5/8 puddle welds 6 or structural TABLE 4B: LIGHTWEIGHT CONCRETE DECKS - NEW CONSTRUCTION, REROOF (TEAR-OFF) OR RECOVER SYSTEM TYPE D-1: MECHANICALLY ATTACHED ROOF COVER (THROUGH LWC TO ENGAGE STRUCTURAL DECK) Insulation Roof Cover LWC Min. 200 psi, min. 2- inch thick Elastizell Type Attach Membrane Fasteners Attachment (Optional) One or more layers,, min. 0.5-inch Prelim. Attach Firestone HD Fasteners or Firestone Concrete Drive ( only) with Firestone HD Seam Plates Fastened through to engage structural deck, 6- within 6-inch wide laps spaced 114- and sealed with a 1.5-inch heat weld Prepared by: Robert Nieminen, PE Appendix 1, Page 43 of 57

44 TABLE 4C: LIGHTWEIGHT CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE F: NON-INSULATED, BONDED ROOF COVER LWC ULTRAPLY TPO SYSTEMS: LWC-72 Min. 22 ga., type B, Grade 33 vented steel deck at max. 6 ft spans; Tek/5 screws 6 or min. 2,500 psi structural Min. 200 psi, min. 2-inch thick Approved cellular LWIC with optional 1-inch thick, 1.0 pcf EPS holey board. / UP-BA -67.5* LWC-73 Min. 22 ga., type B, Grade 33 vented steel deck at max. 5 ft spans; Tek/5 screws 6 or min. 2,500 psi structural Min. 200 psi, min. 2-inch thick Approved cellular LWIC with optional 1-inch thick, 1.0 pcf EPS holey board. When walkable, LWC is mechanically attached with Firestone Insulation Fastening Plates with Firestone HD Fasteners at a density of 1 per 2 ft 2. / UP-BA * LWC-74 structural Admixture, with optional 1-inch thick, 1.0 pcf EPS holey / UP-BA * ULTRAPLY TPO XR SYSTEMS: LWC-75 Min. 22 ga., type B, Grade 33 vented steel deck at max. 6 ft spans; Tek/5 screws 6 or min. 2,500 psi structural Min. 200 psi, min. 2-inch thick Celcore cellular LWIC with optional 1-inch thick, 1.0 pcf EPS holey board. XR / XR-BA LWC-76 Min. 22 ga., type B, Grade 33 vented steel deck at max. 6 ft spans; 5/8 puddle welds with washer 6 or min. 2,500 psi structural Min. 200 psi, min. 2-inch thick Celcore cellular LWIC with optional 1-inch thick, 1.0 pcf EPS holey board. When walkable, LWC is mechanically attached with Firestone Insulation Fastening Plates with Firestone HD Fasteners at a density of 1 per 2 ft 2. XR / XR-BA -90.0* LWC-77 Min. 22 ga., type B, Grade 33 vented steel deck at max. 6 ft spans; Tek/5 screws 6 or min. 2,500 psi structural Min. 250 psi, min. 2-inch thick Approved cellular LWIC with optional 1-inch thick, 1.0 pcf EPS holey board. When walkable, LWC is mechanically attached with Firestone Insulation Fastening Plates with Firestone HD Fasteners at a density of 1 per 2 ft 2. Note: To qualify the LWIC under this assembly, an ES Products FM-90 Fastener shall achieve a MCRF of 100 lbf when tested per TAS 105. XR / XR-BA -75.0* LWC-78 structural Min. 250 psi, min. 2-inch thick Approved cellular LWIC. Note: To qualify the LWIC under this assembly, an ES Products FM- 90 Fastener shall achieve a MCRF of 95 lbf when tested per TAS 105. XR / XR-BA * LWC-79 Min. 22 ga., type B, Grade 33 vented steel deck at max. 6 ft spans; 5/8 puddle welds with washers 6 Admixture, with optional 1-inch thick, 1.0 pcf EPS holey XR / XR-BA -52.5* LWC-80 Min. 22 ga., type B, Grade 33 vented steel deck at max. 6 ft spans; Traxx/5 screws 6 Admixture, with optional 1-inch thick, 1.0 pcf EPS holey XR / XR-BA -60.0* LWC-81 Min. 22 ga., type B, Grade 33 vented steel deck at max. 5 ft spans; Traxx/5 screws 6 Admixture, with optional 1-inch thick, 1.0 pcf EPS holey XR / XR-BA -82.5* LWC-82 Min. 22 ga., type B, Grade 33 vented steel deck at max. 6 ft spans; Tek/5 screws 6 Min. 300 psi, min. 2-inch thick Elastizell Lightweight Insulating Concrete, with optional 1-inch thick, 1.0 pcf EPS holey board. XR / XR-BA -82.5* LWC-83 Min. 22 ga., type B, Grade 33 vented steel deck at max. 4 ft spans; Traxx/5 screws 6 Admixture, with optional 1-inch thick, 1.0 pcf EPS holey XR / XR-BA -90.0* Prepared by: Robert Nieminen, PE Appendix 1, Page 44 of 57

45 TABLE 4C: LIGHTWEIGHT CONCRETE DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE F: NON-INSULATED, BONDED ROOF COVER LWC LWC-84 LWC-85 LWC-86 LWC-87 Min. 22 ga., type B, Grade 33 vented steel deck at max. 6 ft spans; Tek/5 screws 6 structural Min. 22 ga., type B, Grade 33 vented steel deck at max. 6 ft spans; 5/8 puddle welds with washers 6 structural Admixture, with optional 1-inch thick, 1.0 pcf EPS holey When walkable, LWC is mechanically attached with Firestone Insulation Fastening Plates with Firestone HD Fasteners at a density of 1 per 2 ft 2. Admixture, with optional 1-inch thick, 1.0 pcf EPS holey Min. 250 psi, min. 2-inch thick Elastizell Range II Lightweight Insulating Concrete with optional 1-inch thick, 1.0 pcf EPS holey board. When walkable, LWC is mechanically attached with Firestone Insulation Fastening Plates with Firestone HD Fasteners at a density of 1 per 2 ft 2. Min. 250 psi, min. 2-inch thick Elastizell Range II Lightweight Insulating Concrete with 1-inch thick, 1.0 pcf EPS holey board. XR / XR-BA -90.0* XR / XR-BA -90.0* XR / XR-BA -82.5* XR / XR-BA -90.0* LWC-88 structural Min. 250 psi, min. 2-inch thick Elastizell Range II Lightweight Insulating Concrete. No EPS holey board. XR / XR-BA * LWC-89 structural Admixture, with optional 1-inch thick, 1.0 pcf EPS holey XR / XR Stick; 4- (full coverage) -75.0* Prepared by: Robert Nieminen, PE Appendix 1, Page 45 of 57

46 CWF-1. Tectum CWF-2. Tectum CWF-3. Tectum CWF-4. CWF-5. Tectum or Fibroplank Tectum or Fibroplank TABLE 5A: CEMENTITIOUS WOOD FIBER DECKS - NEW CONSTRUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-1A: BONDED INSULATION, BONDED ROOF COVER Type Attach Type Attach, full coverage 3M CR-20 3M CR-20 (Optional) Min inch Dens, Dens Prime or (Optional) Min inch Dens Prime or SECUROCK (Optional) Min inch Dens or SECUROCK Gypsum- Fiber Roof Board (Optional) Min inch Dens, Dens Prime or (Optional) Min inch Dens Prime or SECUROCK / UP-BA / LVOC-BA-, full coverage / UP-BA 3M CR-20 / UP-BA -52.5* 3M CR-20 / LVOC-BA * TABLE 5B: CEMENTITOUS WOOD FIBER DECKS - NEW CONSTUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-2: MECHANICALLY ATTACHED ANCHOR SHEET, BONDED INSULATION, BONDED ROOF COVER Anchor Sheet Base Insulation Top Insulation Roof Cover / Type Fasten Attach Type Attach Type Attach Adhesive CWF-6. Tectum SBS Base, SBS Premium Base, MB Base or APP 160 Two Piece Locking Nail 9- in the min. 2-inch lap and 18- in two, equally spaced center rows Min. 1.5-inch ISO 95+ (Optional) Min inch Dens, Dens Prime or SECUROCK Gypsum-Fiber Roof Board / UP- BA CWF-7. Tectum SBS Base, SBS Premium Base, MB Base or APP 160 Two Piece Locking Nail 9- in the min. 2-inch lap and 18- in two, equally spaced center rows Min. 1.5-inch ISO 95+ (Optional) Min inch Dens Prime or SECUROCK Gypsum-Fiber Roof Board / LVOC-BA- Prepared by: Robert Nieminen, PE Appendix 1, Page 46 of 57

47 TABLE 6A: GYPSUM DECKS - REROOF (TEAR-OFF) SYSTEM TYPE A-1A: BONDED INSULATION, BONDED ROOF COVER (See Notes 1 & 12) Type Attach Type Attach ULTRAPLY TPO SYSTEMS: G-1. Existing poured gypsum or gypsum plank (Optional) Additional layers of base insulation LVOC- BA * G-2. Existing poured gypsum or gypsum plank Min inch Dens Prime or SECUROCK Gypsum-Fiber Roof Board LVOC- BA * G-3. Existing poured gypsum or gypsum plank Min inch Dens or SECUROCK Gypsum-Fiber Roof Board / UP-BA * G-4. Existing poured gypsum or gypsum plank (Optional) Min inch ISO 95+ Min. 0.5-inch ISOGARD HD / UP-BA G-5. Existing poured gypsum or gypsum plank 3M CR-20 (Optional) Additional layers base insulation 3M CR-20 LVOC- BA * G-6. Existing poured gypsum or gypsum plank 3M CR-20 Min inch Dens or SECUROCK Gypsum-Fiber Roof Board 3M CR-20 / UP-BA * G-7. Existing poured gypsum or gypsum plank 3M CR-20 Min inch Dens Prime or SECUROCK Gypsum-Fiber Roof Board 3M CR-20 LVOC- BA * G-8. Existing poured gypsum or gypsum plank (Optional) Min inch Dens, Dens Prime or / UP-BA * G-9. Existing poured gypsum or gypsum plank (Optional) Min inch Dens Prime or SECUROCK / LVOC-BA * ULTRAPLY TPO XR SYSTEMS: G-10. Existing poured gypsum or gypsum plank (Optional) Min inch ISO 95+ Min. 0.5-inch ISOGARD HD XR / XR Stick, 4- (full coverage) Prepared by: Robert Nieminen, PE Appendix 1, Page 47 of 57

48 TABLE 6B: GYPSUM DECKS - NEW CONSTUCTION OR REROOF (TEAR-OFF) SYSTEM TYPE A-2: MECHANICALLY ATTACHED ANCHOR SHEET, BONDED INSULATION, BONDED ROOF COVER (See Note 1) Anchor Sheet Base Insulation Top Insulation Type Fasten Attach Type Attach Type Attach Roof Cover / Adhesive G-11. Existing gypsum deck SBS Base, SBS Premium Base, MB Base or APP 160 Two Piece Locking Nail (MCRF > 105 lbf) 9- in the min. 2-inch lap and 18- in two, equally spaced center rows Min. 1.5-inch ISO 95+ (Optional) Min inch Dens, Dens Prime or SECUROCK Gypsum-Fiber Roof Board / UP- BA G-12. Existing gypsum deck SBS Base, SBS Premium Base, MB Base or APP 160 Two Piece Locking Nail (MCRF > 105 lbf) 9- in the min. 2-inch lap and 18- in two, equally spaced center rows Min. 1.5-inch ISO 95+ (Optional) Min inch Dens Prime or SECUROCK Gypsum-Fiber Roof Board / LVOC-BA- Prepared by: Robert Nieminen, PE Appendix 1, Page 48 of 57

49 TABLE 7A: RECOVER APPLICATIONS SYSTEM TYPE A-1A: BONDED INSULATION, BONDED ROOF COVER Substrate (See Notes 1 & 12) Type Attach Type Attach Roof Cover ULTRAPLY TPO SYSTEMS R-1 Existing asphaltic BUR or granule surface with optional Tapered ISO 95+ Hot Asphalt Min. 0.5-inch Firestone FiberTop Hot Asphalt LVOC-BA * R-2 Existing asphaltic BUR or granule surface Hot Asphalt (Optional) Tapered ISO 95+ Hot asphalt LVOC-BA * R-3 Existing asphaltic BUR or granule surface with optional Tapered ISO 95+ Hot Asphalt Min inch Dens, Dens Prime or SECUROCK Gypsum- Fiber Roof Board Hot Asphalt / UP-BA * R-4 Existing asphaltic BUR or granule surface with optional Tapered ISO 95+ Hot Asphalt Min inch Dens Prime or SECUROCK Gypsum-Fiber Roof Board Hot Asphalt / LVOC-BA * R-5 Existing asphaltic BUR or granule surface (Optional) Min inch Dens, Dens Prime or SECUROCK Gypsum- Fiber Roof Board / UP-BA * R-6 Existing asphaltic BUR or granule surface (Optional) Min inch Dens Prime or SECUROCK Gypsum-Fiber Roof Board / LVOC-BA * R-7 Existing asphaltic BUR or granule surface (Optional) Min. 1.5-inch ISO 95+ Min. 0.5-inch ISOGARD HD LVOC-BA * R-8 (Optional) Additional layers of base insulation and/or min. 0.5-inch Tapered ISO 95+ / WBBA-S, R-9 Min. 1-inch (Optional) Additional layers of base insulation and/or min. 0.5-inch Tapered / WBBA-S, * R-10 (Optional) Additional layers of base insulation and/or min. 0.5-inch Tapered ISO 95+ or Tapered LVOC-BA * R-11 min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 0.5-inch ISOGARD HD / WBBA-S, * R-12 min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 0.5-inch ISOGARD HD LVOC-BA * R-13 min. 0.5-inch Tapered ISO 95+ or Tapered ; Min inch Dens Prime or / WBBA-S, * Prepared by: Robert Nieminen, PE Appendix 1, Page 49 of 57

50 R-14 R-15 R-16 R-17 R-18 R-19 R-20 R-21 R-22 R-23 R-24 R-25 R-26 R-27 Substrate (See Notes 1 & 12) Existing asphaltic BUR or granule surface Existing asphaltic BUR or granule surface Existing asphaltic BUR or granule surface Existing asphaltic BUR or granule surface Existing asphaltic BUR or granule surface TABLE 7A: RECOVER APPLICATIONS SYSTEM TYPE A-1A: BONDED INSULATION, BONDED ROOF COVER Type Attach Type Attach min. 0.5-inch Tapered ISO 95+ or Tapered ; Min inch Dens Prime or min. 0.5-inch Tapered ISO 95+ or Tapered ; Min inch Dens Prime or 3M CR-20 (Optional) Additional layers base insulation 3M CR-20 Roof Cover LVOC-BA LVOC-BA- LVOC-BA- 3M CR-20 Min inch Dens or 3M CR-20 / UP-BA * Min. 1-inch or or 3M CR-20 Min inch Dens Prime or SECUROCK Gypsum-Fiber Roof Board (Optional) Additional layers of base insulation and/or min. 0.5-inch Tapered ISO 95+ (Optional) Additional layers of base insulation and/or min. 0.5-inch Tapered (Optional) Additional layers of base insulation and/or min. 0.5-inch Tapered ISO 95+ or Tapered min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 0.5-inch ISOGARD HD min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 0.5-inch ISOGARD HD min. 0.5-inch Tapered ISO 95+ or Tapered ; Min inch Dens Prime or min. 0.5-inch Tapered ISO 95+ or Tapered ; Min inch Dens Prime or (Optional) Additional layers of base insulation and/or min. 0.5-inch Tapered ISO 95+ (Optional) Additional layers of base insulation and/or min. 0.5-inch Tapered 3M CR-20 LVOC-BA- / WBBA-S, / WBBA-S, LVOC-BA- / WBBA-S, LVOC-BA- / WBBA-S, LVOC-BA- / WBBA-S, / WBBA-S, * * * * * * * * * * -60.0* Prepared by: Robert Nieminen, PE Appendix 1, Page 50 of 57

51 Substrate (See Notes 1 & 12) R-28 Existing asphaltic BUR R-29 R-30 Existing asphaltic BUR or granule surface R-31 Existing asphaltic BUR R-32 TABLE 7A: RECOVER APPLICATIONS SYSTEM TYPE A-1A: BONDED INSULATION, BONDED ROOF COVER Type Attach Type Attach or or or or or R-33 Existing asphaltic BUR R-34 Existing asphaltic BUR Min. 1-inch R-35 Existing asphaltic BUR R-36 Existing asphaltic BUR R-37 Existing asphaltic BUR R-38 Existing asphaltic BUR R-39 Existing asphaltic BUR R-40 Existing asphaltic BUR R-41 Existing asphaltic BUR R-42 Existing asphaltic BUR (Optional) Additional layers of base insulation and/or min. 0.5-inch Tapered ISO 95+ or Tapered (Optional) Additional layers of base insulation, 6-, 6-, 6-, 6-, 6-, 6-, 6-, 6-, 6-, 6- min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 0.5-inch ISOGARD HD min. 0.5-inch Tapered ISO 95+ or Tapered ; Min inch Dens Prime or Min inch Dens Prime or SECUROCK Gypsum-Fiber Roof Board (Optional) Additional layers of base insulation and/or min. 0.5-inch Tapered ISO 95+ (Optional) Additional layers of base insulation and/or min. 0.5-inch Tapered (Optional) Additional layers of base insulation and/or min. 0.5-inch Tapered ISO 95+ or Tapered min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 0.5-inch ISOGARD HD min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 0.5-inch ISOGARD HD min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 0.5-inch FiberTop C or S min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 0.5-inch FiberTop C or S min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 0.5-inch FiberTop C or S min. 0.5-inch Tapered ISO 95+ or Tapered ; Min inch Dens Prime or min. 0.5-inch Tapered ISO 95+ or Tapered ; Min inch Dens Prime or, 6-, 6-, 6-, 6-, 6-, 6-, 6-, 6-, 6-, 6- Roof Cover LVOC-BA- LVOC-BA-, WBBA-S, LVOC-BA-, WBBA-S, LVOC-BA-, WBBA-S, LVOC-BA-, WBBA-S, / WBBA-S, / WBBA-S, LVOC-BA- / WBBA-S, LVOC-BA- LVOC-BA / WBBA-S, / LVOC-BA- / WBBA-S, LVOC-BA -60.0* * -60.0* -60.0* * * * * * -60.0* * * * * Prepared by: Robert Nieminen, PE Appendix 1, Page 51 of 57

52 TABLE 7A: RECOVER APPLICATIONS SYSTEM TYPE A-1A: BONDED INSULATION, BONDED ROOF COVER Substrate (See Notes 1 & 12) R-43 Existing asphaltic BUR R-44 Existing asphaltic BUR Type Attach Type Attach, 6-, 6- min. 0.5-inch Tapered ISO 95+ or Tapered ; Min inch Dens Prime or min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 19/32-inch plywood, 6-, 6- Roof Cover / LVOC-BA- LVOC-BA-, WBBA-S, * * R-45 (Optional) Additional layers of base insulation and/or min. 0.5-inch Tapered ISO 95+ / WBBA-S, R-46 (Optional) Additional layers of base insulation and/or min. 0.5-inch Tapered ISO 95+ LVOC-BA * R-47 Min. 1-inch (Optional) Additional layers of base insulation and/or min. 0.5-inch Tapered LVOC-BA-, WBBA-S, * R-48 min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 0.5-inch ISOGARD HD / WBBA-S, * R-49 min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 0.5-inch ISOGARD HD LVOC-BA * R-50 min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 0.5-inch FiberTop C or S LVOC-BA -60.0* R-51 min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 0.5-inch FiberTop C or S / WBBA-S, * R-52 R-53 R-54 R-55 min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 0.5-inch FiberTop C or S min. 0.5-inch Tapered ISO 95+ or Tapered ; Min inch Dens Prime or min. 0.5-inch Tapered ISO 95+ or Tapered ; Min inch Dens Prime or min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 19/32-inch plywood / LVOC-BA- / WBBA-S, LVOC-BA- LVOC-BA-, WBBA-S, * * * * ULTRAPLY TPO XR SYSTEMS R-56 Min inch Dens Prime or SECUROCK Hot Asphalt N/A XR / Hot Asphalt * Prepared by: Robert Nieminen, PE Appendix 1, Page 52 of 57

53 TABLE 7A: RECOVER APPLICATIONS SYSTEM TYPE A-1A: BONDED INSULATION, BONDED ROOF COVER R-57 R-58 R-59 R-60 R-61 R-62 R-63 R-64 R-65 Substrate (See Notes 1 & 12) Existing granulesurfaced, asphaltic R-66 Existing asphaltic BUR R-67 R-68 R-69 Existing asphaltic BUR Type Attach Type Attach Min inch Dens Prime or SECUROCK or min. 0.5-inch Tapered ISO 95+ or followed by Min inch Dens Prime or min. 0.5-inch Tapered ISO 95+ or followed by Min inch Dens Prime or min. 0.5-inch Tapered ISO 95+ or followed by Min inch Dens Prime or Roof Cover XR / Hot Asphalt XR / Hot Asphalt XR / Hot Asphalt Hot Asphalt N/A XR / XR-BA * ; I.S.O. Stick;, 6- (Optional) Additional layer of base insulation or min. 0.5-inch Tapered ISO 95+ or min. 0.5-inch Tapered ISO 95+ or followed by min. 0.5-inch ISOGARD HD min. 0.5-inch Tapered ISO 95+ or Tapered ; Min inch Dens Prime or min. 0.5-inch Tapered ISO 95+ or followed by min. 0.5-inch ISOGARD HD min. 0.5-inch Tapered ISO 95+ or Tapered ; Min inch Dens Prime or min. 0.5-inch Tapered ISO 95+ or Tapered ; Min inch Dens Prime or min. 0.5-inch Tapered ISO 95+ or followed by min. 0.5-inch ISOGARD HD min. 0.5-inch Tapered ISO 95+ or followed by Min inch Dens Prime or min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 0.5-inch FiberTop C or S ; I.S.O. Stick; * * * XR / XR-BA * XR / XR-BA * XR / XR-BA * XR / XR-BA * XR / XR-BA * XR / XR-BA -60.0* XR / XR-BA * XR / XR-BA *, 6- XR / XR-BA Prepared by: Robert Nieminen, PE Appendix 1, Page 53 of 57

54 TABLE 7A: RECOVER APPLICATIONS SYSTEM TYPE A-1A: BONDED INSULATION, BONDED ROOF COVER Substrate (See Notes 1 & 12) R-70 Existing asphaltic BUR R-71 R-72 R-73 Existing asphaltic BUR R-74 R-75 R-76 R-77 R-78 R-79 R-80 R-81 Type Attach Type Attach Min inch Dens Prime or SECUROCK or min. 0.5-inch ISOGARD HD Min. 0.5-inch ISOGARD HD or or, 6- ; I.S.O. Spray S; ;, 6- ; I.S.O. Stick; ; I.S.O. Stick; ; I.S.O. Stick; ; I.S.O. Stick; ; I.S.O. Stick; ; I.S.O. Stick; ; I.S.O. Stick; min. 0.5-inch Tapered ISO 95+ or Tapered ; Min inch Dens Prime or min. 0.5-inch Tapered ISO 95+ or Tapered ; Min. 0.5-inch FiberTop C or S min. 0.5-inch Tapered ISO 95+ or Tapered ; Min inch Dens Prime or (Optional) Additional layer of base insulation or min. 0.5-inch Tapered ISO 95+ or (Optional) Additional layer of base insulation or min. 0.5-inch Tapered ISO 95+ or min. 0.5-inch Tapered ISO 95+ or followed by min. 0.5-inch ISOGARD HD min. 0.5-inch Tapered ISO 95+ or followed by min. 0.5-inch ISOGARD HD min. 0.5-inch Tapered ISO 95+ or followed by min. 0.5-inch ISOGARD HD min. 0.5-inch Tapered ISO 95+ or followed by Min inch Dens Prime or min. 0.5-inch Tapered ISO 95+ or followed by Min inch Dens Prime or, 6- Roof Cover XR / XR-BA * XR / XR-BA XR / XR-BA * N/A N/A ; I.S.O. Stick; ; I.S.O. Stick; ; I.S.O. Stick; ; I.S.O. Stick; ; I.S.O. Stick; ; I.S.O. Stick; ; I.S.O. Stick; XR / I.S.O. Spray S, XR Stick, 4-inch XR / I.S.O Spray S, XR Stick, 6-inch XR / I.S.O Spray S, XR Stick, 6-inch XR / I.S.O Spray S, XR Stick, 4-inch (full coverage) XR / I.S.O Spray S, XR Stick, 12-inch XR / I.S.O Spray S, XR Stick, 6-inch XR / I.S.O Spray S, XR Stick, 4-inch (full coverage) XR / I.S.O Spray S, XR Stick, 12-inch XR / I.S.O Spray S, XR Stick, 6-inch -82.5* * -82.5* -60.0* Prepared by: Robert Nieminen, PE Appendix 1, Page 54 of 57

55 R-82 R-83 Substrate (See Notes 1 & 12) TABLE 7A: RECOVER APPLICATIONS SYSTEM TYPE A-1A: BONDED INSULATION, BONDED ROOF COVER Type Attach Type Attach R-84 Existing asphaltic BUR R-85 Existing asphaltic BUR R-86 R-87 Min. 0.5-inch ISOGARD HD or Min inch Dens Prime or SECUROCK Min. 0.5-inch ISOGARD HD or Min inch Dens Prime or SECUROCK ; I.S.O. Stick; ; I.S.O. Stick; ; I.S.O. Spray S; ; ; I.S.O. Spray S; ; min. 0.5-inch Tapered ISO 95+ or followed by Min inch Dens Prime or min. 0.5-inch Tapered ISO 95+ or followed by min. 19/32-inch plywood (Optional) Min. 0.5-inch ISOGARD HD or Min inch Dens Prime or (Optional) Min. 0.5-inch ISOGARD HD, Min inch Dens Prime or or min. 19/32-inch plywood N/A ; I.S.O. Stick; ; I.S.O. Stick; ; I.S.O. Spray S; ; N/A Roof Cover XR / I.S.O Spray S, XR Stick, 4-inch (full coverage) XR / I.S.O Spray S, XR Stick, 12-inch XR / I.S.O Spray S, XR Stick, 4-inch XR / I.S.O Spray S, XR Stick, 4-inch XR / I.S.O Spray S, 4- XR / I.S.O Spray S, XR Stick, 4-inch Prepared by: Robert Nieminen, PE Appendix 1, Page 55 of 57

56 TABLE 7B: STEEL - RECOVER SYSTEM TYPE C-2: PLATE-BONDED ROOF COVER Note: All areas where the existing metal panels do not lay flush on the underlying purlin shall have a 0.25-inch diameter pilot hole pre-drilled into the panel prior to driving the Purlin Fastener into the purlin. Substrate (See Notes 1 & 11) Insulation Layer Fasten Attach Spacing R-88 Existing standing seam or lap seam metal roof covers having min. 3/16-inch to max. ¼-inch thick steel purlins spaced max. 60- One or more layers, any combination, preliminarily fastened per FM Approvals requirements Firestone Purlin Fasteners and InvisiWeld Plates are fastened through to purlins 12- along purlins bonded to InvisiWeld Plates with RhinoBond Portable Plate Bonding Tool and weighted RhinoBond Cooling Clamps R-89 Existing standing seam or lap seam metal roof covers having min. ¼-inch thick steel purlins spaced max One or more layers, any combination, preliminarily fastened per FM Approvals requirements Firestone Purlin Fasteners and InvisiWeld Plates are fastened through to purlins 6- along purlins bonded to InvisiWeld Plates with RhinoBond Portable Plate Bonding Tool and weighted RhinoBond Cooling Clamps R-90 Existing standing seam or lap seam metal roof covers having min. 3/16-inch to max. ¼-inch thick steel purlins spaced max. 60- One or more layers, any combination, preliminarily fastened per FM Approvals requirements Firestone Purlin Fasteners and InvisiWeld Plates are fastened through to purlins 6- along purlins bonded to InvisiWeld Plates with RhinoBond Portable Plate Bonding Tool and weighted RhinoBond Cooling Clamps TABLE 7C: STEEL - RECOVER SYSTEM TYPE D-1: INSULATED, MECHANICALLY ATTACHED ROOF COVER Note: All areas where the existing metal panels do not lay flush on the underlying purlin shall have a 0.25-inch diameter pilot hole pre-drilled into the panel prior to driving the Purlin Fastener into the purlin. R-91 (See Notes 1 & 11) Existing standing seam or lap seam metal roof covers having min. 3/16-inch to max. ¼-inch thick steel purlins spaced max. 90- Insulation Roof Cover Type Attach Membrane Fasteners Attach One or more layers, any combination Prelim. attached Firestone Purlin Fasteners and Firestone HD Seam Plates 12- within 6-inch wide laps spaced max. 90- to engage steel purlin. Laps sealed with 1.5- inch heat weld R-92 Existing standing seam or lap seam metal roof covers having min. 3/16-inch to max. ¼-inch thick steel purlins spaced max One or more layers, any combination Prelim. attached Firestone Purlin Fasteners and Firestone HD Seam Plates 6- within 6-inch wide laps spaced max to engage steel purlin. Laps sealed with 1.5- inch heat weld TABLE 7D: STEEL - RECOVER SYSTEM TYPE D-2: INSULATED, MECHANICALLY ATTACHED ROOF COVER (RMA STRIPS) Note: All areas where the existing metal panels do not lay flush on the underlying purlin shall have a 0.25-inch diameter pilot hole pre-drilled into the panel prior to driving the Purlin Fastener into the purlin. R-93 (See Notes 1 & 11) Existing standing seam or lap seam metal roof covers having min. 3/16-inch to max. ¼-inch thick steel purlins spaced max. 10- Insulation Roof Cover Type Attach Membrane Fasten Attach One or more layers, any combination Prelim. attached Firestone Purlin Fasteners and Firestone Coiled Metal Batten Strip Firestone UltraPly QuickSeam R.M.A. Strips are applied over the insulation spaced 120- positioned over each steel purlin location. The batten is centered over each strip and fastened into the purlins 6- Roof cover adhered to each strip by first priming the membrane underside with Firestone QuickPrime at the strip location, then rolling into place with a hand roller. The min. 2-inch side laps are sealed with a min. 1.5-inch outside heat weld Prepared by: Robert Nieminen, PE Appendix 1, Page 56 of 57

57 TABLE 7E: RECOVER APPLICATIONS SYSTEM TYPE E: NON-INSULATED, MECHANICALLY ATTACHED ROOF COVER Roof Cover R-94 Min. 22 ga., type B, Grade 80 steel XR Firestone HD Plus Fasteners (steel only) with Firestone HD Plus Seam Plates 12- within 6-inch wide laps spaced 114- Laps sealed with 1.5-inch heat weld R-95 Min. 22 ga., type B, Grade 33 steel or struct. conc. XR Firestone HD Fasteners with Firestone HD Seam Plates 6- within 6-inch wide laps spaced 114- Laps sealed with 1.5-inch heat weld R-96 Min. 22 ga., type B, Grade 80 steel XR Firestone HD Plus Fasteners (steel only) with Firestone HD Plus Seam Plates 6- within 6-inch wide laps spaced 114- Laps sealed with 1.5-inch heat weld TABLE 7F: RECOVER APPLICATIONS SYSTEM TYPE F: NON-INSULATED, BONDED ROOF COVER (See Notes 1 & 12) Type Roof Cover Application R-97 Existing asphaltic BUR or granule-surfaced roof cover XR, XR Stick, 12- R-98 Existing granule-surfaced, asphaltic roof cover XR, XR Stick, * R-99 Existing asphaltic BUR over structural deck XR, * R-100 Existing asphaltic BUR over structural deck XR XR Stick, * R-101 d SBS over structural deck XR XR Stick, R-102 d APP over structural deck XR XR Stick, R-103 Existing asphaltic BUR or granule surface over structural or steel deck XR Hot asphalt * Prepared by: Robert Nieminen, PE Appendix 1, Page 57 of 57