HP A9891A Smart Array 6404 Controller Installation Guide

Transcription

2 Legal Notices The information in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this manual, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be held liable for errors contained herein or direct, indirect, special, incidental or consequential damages in connection with the furnishing, performance, or use of this material. Warranty A copy of the specific warranty terms applicable to your Hewlett-Packard product and replacement parts can be obtained from your local Sales and Service Office. U.S. Government License Proprietary computer software. Valid license from HP required for possession, use or copying. Consistent with FAR and , Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor's standard commercial license. Copyright Notice Copyright 2007 Hewlett-Packard Development Company L.P. All rights reserved. Reproduction, adaptation, or translation of this document without prior written permission is prohibited, except as allowed under the copyright laws. Trademark Notices UNIX is a registered trademark in the United States and other countries, licensed exclusively through The Open Group Localized Documentation This Installation Guide has been translated to: 2

3 Contents 1. Smart Array 6404 Controller HP-UX Installation Smart Array 6404 Controller Components Smart Array 6404 HP-UX Installation Prerequisites Preparing for the Smart Array 6404 Controller Installation Installing Smart Array 6404 Controller Hardware (Offline) Installing Smart Array 6404 Controller Hardware (Online) Smart Array 6404 HP-UX Software Installation Locating Software for the Smart Array 6404 Controller Installing Software for Smart Array 6404 Controller Install the Software After HP-UX Installation Verifying the Installation Setting up a Smart Array 6404 Controller As a Boot Device Array Configuration Limitations Offline Configuration of HP-UX 11i v1 Using Ignite-UX Using ORCA (IA Platforms Only) Smart Array 6404 Controller OpenVMS Installation Smart Array 6402 Controller Components Smart Array 6404 OpenVMS Installation Prerequisites Smart Array 6404 OpenVMS Quick Installation Install Smart Array 6404 Controllers Smart Array 6404 OpenVMS Software Installation Installing the Smart Array Controller to a System Running OpenVMS Installing the Smart Array Controller as a Boot Device Using ORCA ORCA Limitations Configuring Your Logical Boot Drive Issues and Restrictions Issues and Restrictions Awareness A. Declaration of Conformance 3

4 Contents 4

5 1 Smart Array 6404 Controller HP-UX Installation Chapter 1 5

6 Smart Array 6404 Controller HP-UX Installation Smart Array 6404 Controller Components Smart Array 6404 Controller Components Figure 1-1 Smart Array 6404 Controller Table 1-1 Item ID Controller Components Description 1 Internal SCSI connector, port A1* 2 Internal SCSI connector, port A2* 3 External SCSI connector, port A1* 4 External SCSI connector, port A2* 5 Controller battery 6 Battery-backed cache module 7 Connector for expansion board NOTE Do not use both the internal and external connectors on one port simultaneously. The card will not function if both connectors on one port are used. 6 Chapter 1

7 Smart Array 6404 Controller HP-UX Installation Smart Array 6404 HP-UX Installation Prerequisites Smart Array 6404 HP-UX Installation Prerequisites Before installing the Smart Array 6404 controller, ensure that the following hardware and software prerequisites are met: Check the RAID-01 (ciss) HP Smart Array Controller Driver Release Notes for your HP-UX version for known problems or other information needed for installation. These documents are available in the Smart Array (RAID) section of Confirm that the Smart Array 6404 controller and software are supported on the HP server with the version of HP-UX that you are using; see the HP Smart Array RAID Controllers Support Matrix located in the Smart Array (RAID) section of for more information. Check the HP server s documentation to determine if additional tools are required for component installation at Check the HP server s documentation for specific instructions on controller installation. Check your system hardware documentation to determine if OL* or OLAR are supported. For detailed instructions and information on using the OL* feature, see Interface Card OL* Support Guide for 11i v2 or later. For detailed instructions and information on using the OLAR feature, see Configuring HP-UX for Peripherals for 11i v1. For detailed information about slots in entry-level Integrity servers, see the I/O Slot Matrix - Entry Level Integrity Servers in the System Administration section of You can view, download, or print all documentation from Confirm that you have the Smart Array 6404 controller software bundle (RAID-01). This bundle is included on CD or available on the web at Confirm that HP-UX super-user privileges are available; they are necessary to complete the installation. Confirm that the /usr/bin, /usr/sbin, and /sbin directories are in your PATH by logging in as root and using the echo $PATH command. Take note of the configuration of the system before adding/removing components. For more information about the required operating system versions, see the RAID-01 (ciss) HP Smart Array Controller Driver Release Notes. Chapter 1 7

8 Smart Array 6404 Controller HP-UX Installation Preparing for the Smart Array 6404 Controller Installation Preparing for the Smart Array 6404 Controller Installation WARNING Before installing a Smart Array 6404 Controller in a server, backup all data. This step is mandatory if the disks were not previously configured on a Smart Array Controller, because the data format will not be recognized and the existing data will not be preserved. CAUTION In systems using external data storage, be sure that the server is the first unit powered down and the last unit to be powered back up. Doing this ensures that the system will not erroneously mark the disk drives as FAILED. WARNING To reduce the risk of personal injury or damage to the equipment, consult the safety information and user documentation provided with your server before attempting installation. Many computers are capable of producing energy levels that are considered hazardous. These computers are intended to be serviced by qualified personnel trained to deal with those hazards. Do not remove enclosures or attempt to bypass any interlocks that may be provided for the purpose of removing these hazardous conditions. CAUTION Electrostatic discharge (ESD) can damage electronic components. Be sure that you are properly grounded before continuing the installation procedure. The Smart Array Controllers contain electronic components that can easily be damaged by small amounts of static electricity. To avoid damage, follow these guidelines: Store the controller in its antistatic plastic bag until you are ready to install it Work in a static-free area, if possible Handle the controller only by the edges. Do not touch electronic components or electrical traces If you must lay the controller down, place it on a non-conductive mat or surface Before beginning installation, and without removing the Smart Array Controller from its antistatic bag, inspect the controller for any signs of obvious damage, such as chipped or loose components. Contact HP if the controller is damaged. 8 Chapter 1

9 Smart Array 6404 Controller HP-UX Installation Installing Smart Array 6404 Controller Hardware (Offline) Installing Smart Array 6404 Controller Hardware (Offline) Step 1. Power off the system. If the system is running, shut it down. Wait for the system to shut down completely, and then power off the system. Power off any peripheral devices that are attached to the server. Unplug the AC power cord(s) from the outlet, and then from the server and peripheral devices. Step 2. Access the system controller bay. Open the system to gain access to the PCI backplane. Step 3. Install the controller. Insert the controller into the fastest-performance PCI slot available. For detailed information about slots in entry-level Integrity servers, see the I/O Slot Matrix - Entry Level Integrity Servers in the System Administration section of Slide the controller edge-connector into the PCI slot until it is fully seated. Secure the controller. Step 4. Reassemble the system. Step 5. Power on the system. Power on any peripheral devices that are attached to the server. Power on the system. Installing Smart Array 6404 Controller Hardware (Online) If your system has one or more slots that support OL* or OLAR and you want to use OL* or OLAR to install the controller in one of those slots follow these steps: Step 1. Confirm that the latest version of the ciss driver (Smart Array Controller software) is installed on your system. See the Verifying the Installation section in the HP Smart Array 6400 Series Controller Support Guide. Step 2. Install the Smart Array Controller in your HP-UX system according to the procedure described in the latest edition of the Interface Card OL* Support Guide for 11i v2 or later, or Configuring HP-UX for Peripherals for 11i v1. These documents can be viewed or downloaded at or a hard copy can be ordered from HP. TIP To improve performance, install the Smart Array Controller in a PCI-X 133 MHz slot or available PCI 4X slot. NOTE See the HP Smart Array Controller Support Matrix, located in the Smart Array (RAID) section of to find out if your server supports OL* or OLAR. Chapter 1 9

10 Smart Array 6404 Controller HP-UX Installation Smart Array 6404 HP-UX Software Installation Smart Array 6404 HP-UX Software Installation Locating Software for the Smart Array 6404 Controller The driver, utilities and manpages for the Smart Array 6404 controller are located at the HP Software Depot. Go to Search for A9891A. Click Receive for Free. Select the HP-UX version that your system is running, and fill-out the customer information form. Then click Next. In the Documents column next to the Download Software column, click on Download/Installation Instructions for additional information. Click on the depot that corresponds with the OS you are running to download the driver, utilities and manpages for the Smart Array Controllers. NOTE HP recommends that you install the latest version of the Smart Array 6400 Series Controller firmware. For current firmware recommendations, see the HP Smart Array RAID Controllers Support Matrix. For instructions on how to obtain and install adapter firmware, see the HP Smart Array 6400 Series Support Guide. These documents are available in the Smart Array (RAID) section of Installing Software for Smart Array 6404 Controller The driver, utilities and manpages for the Smart Array 6404 Controller are contained in the RAID-01 bundle located in the downloaded depot. They can be installed using the Software Distributor (SD). The SD is a tool for installing software on HP-UX host systems; it can also be used to remove software from HP-UX host systems. The instructions for using the SD to install or remove the driver, utilities and manpages for the Smart Array 6404 Controller can be downloaded at The RAID-01 bundle is composed of several files that will be copied to the appropriate directories on the host system. User space utilities can be viewed in the /opt/raidsa/bin directory. Install the Software After HP-UX Installation Here are the steps to load the Smart Array 6404 software, using the HP-UX swinstall program. Step 1. Log on to the system as root. Step 2. Insert the software media into the appropriate drive. If the software is being loaded from a CD-ROM, go to step 3; otherwise, go to step 4. The software can also be located at 10 Chapter 1

11 Smart Array 6404 Controller HP-UX Installation Smart Array 6404 HP-UX Software Installation Step 3. Mount the CD-ROM drive by using the System Administration Manager (SAM). Run SAM using the following command: $ sam NOTE System Administration Manager (SAM) is deprecated in HP-UX 11i v3, and replaced by System Management Homepage (SMH). When you start SAM, the SMH command is automatically called. For more information, see the smh(1m) man page. Select Disk and File System Select Disk Devices Select the CD-ROM drive that contains your software media Select Mount from the Actions Menu Specify the mount directory and deselect the At Every System Boot option Step 4. Run the swinstall program using the following command: $ /usr/sbin/swinstall This opens the Software Selection window. Step 5. Change the Source Depot Type and Source Host Name, if necessary, and enter the software location in the Source Depot Path field. If installing from CD-ROM, the software location is the mount directory. Select the OK button to return to the Software Selection window. Step 6. The Software Selection window now contains a list of available software to install. Step 7. Highlight the Smart Array 6404 software, for example: RAID-01 B RAID SA; Supptd HW=A7143A/A9890A/A9891A Choose Mark for Install from the Actions menu; this chooses the highlighted software. Step 8. From the Actions menu, select the Install... menu. This begins product installation and opens the Install Analysis window. Step 9. Click OK in the Install Analysis window when the Status field displays a Ready message. Step 10. Click YES in the Confirmation window to start software installation. When the processing is finished, the Status field displays a Ready message. Select Done. The Note window opens. Step 11. Click OK in the Note window to reboot. The user interface disappears and the system reboots. When the system comes back up, log on to the system as root and view the /var/adm/sw/swagent.log and /var/adm/sw/swinstall.log files to view error or warning messages that may have occurred during the installation. Step 12. Verify that all installed Smart Array 6404 controllers have a software state of CLAIMED, by running the ioscan -fnc ext_bus grep ciss command. Chapter 1 11

12 Smart Array 6404 Controller HP-UX Installation Verifying the Installation Verifying the Installation After the system reboots, verify that the installation was successful by following these steps: Step 1. Issue the swlist command: swlist If the Smart Array Controller is installed correctly, the generated output will look similar to the following: When running HP-UX 11i v1 the generated output will look like this: RAID-01 B RAID SA; Supptd HW=A7143A/A9890A/A9891A When running HP-UX 11i v2 the generated output will look like this: RAID-01 B RAID SA; Supptd HW=A7143A/A9890A/A9891A When running HP-UX 11i v3 the generated output will look like this: RAID-01 B RAID SA; Supptd HW=A7143A/A9890A/A9891A Step 2. Issue the ioscan -kfnd ciss command: ioscan -kfnd ciss If the Smart Array Controller software is installed correctly, the generated output will look similar to this: # ioscan -kfnd ciss Class I H/W Path Driver S/W State H/W Type Description ======================================================================== ext_bus 4 0/3/1/0/4/0 ciss CLAIMED INTERFACE PCI-X SmartArray 6404 RAID Controller /dev/ciss4 ext_bus 7 0/3/1/0/5/0 ciss CLAIMED INTERFACE PCI-X SmartArray 6404 RAID Controller /dev/ciss7 ext_bus 6 0/5/1/0/4/0 ciss CLAIMED INTERFACE PCI-X SmartArray 6402 RAID Controller /dev/ciss6 If the software is not installed correctly, re-install it using swinstall. 12 Chapter 1

13 Smart Array 6404 Controller HP-UX Installation Setting up a Smart Array 6404 Controller As a Boot Device Setting up a Smart Array 6404 Controller As a Boot Device The Smart Array 6404 Controller can be set up as a boot device. NOTE For PA-RISC systems, use Ignite/UX and saconfig to create the logical drives. For Integrity systems, use the Option ROM Configuration for Arrays (ORCA) to create the logical drives. Array Configuration Limitations For the most efficient use of drive space, do not mix drives of different capacities within the same array. The configuration utility treats all physical drives in an array as if they have the same capacity as the smallest drive in the array. The excess capacity of any larger drives is wasted because it is unavailable for data storage. The probability that an array will experience a drive failure increases with the number of physical drives in the array. If you configure a logical drive with RAID 5, keep the probability of failure low by using no more than 14 physical drives in the array. Offline Configuration of HP-UX 11i v1 Using Ignite-UX To set up a Smart Array 6404 Controller as a boot device, you must install HP-UX 11i v1 on one of the controller s logical drives. For PA systems follow this procedure: Step 1. Start Ignite-UX from the HP-UX 11i v1 Core OS Install and Recovery Media. The Ignite-UX Welcome screen displays: Welcome to Ignite-UX! Use the <tab> key to navigate between fields, and the arrow keys within fields. Use the <return/enter> key to select an item. Use the <return/enter> or <space-bar> to pop-up a choices list. If the menus are not clear, select the "Help" item for more information. Hardware Summary: System Model: 9000/800/A500-5X [ Scan Again ] Disks: 3 (204.6GB) Floppies: 0 LAN cards: 1 CD/DVDs: 0 Tapes: 0 Memory: 4096Mb Graphics Ports: 0 IO Buses: 7 CPUs: 1 [ H/W Details ] [ Install HP-UX ] [ Run a Recovery Shell ] [ Advanced Options ] [ Reboot ] [ Help ] Step 2. Select Run a Recovery Shell. The Recovery Shell screen displays: NOTE: Creating the second RAM disc and mounting on /dev... * Generating device file for the second ramdisc... * Loading mkfs to make a file system... version 4 layout sectors, blocks of size 1024, log size 1024 blocks Chapter 1 13

14 Smart Array 6404 Controller HP-UX Installation Setting up a Smart Array 6404 Controller As a Boot Device unlimited inodes, largefiles not supported data blocks, free data blocks 1 allocation units of blocks, data blocks last allocation unit has data blocks * Loading mount to mount/dev/ram1 file system... * Mounting /dev/ram1 file system succeeded! * Copying /dev.old files back to /dev succeeds! * Loading insf to create disk device files... * Creating disk device files... * Loading in a shell... NOTE: Pushing a shell, you will have to use "reboot" to reboot the system when done. Use the "loadfile" command to bring in more commands as you need them. # Step 3. At the recovery shell prompt, enter: loadfile -l INSTCMDS/opt/raidsa/bin/ciss_insf # loadfile -l INSTCMDS /opt/raidsa/bin/ciss_insf # Step 4. At the next prompt, enter: /opt/raidsa/bin/ciss_insf and verify that the device file for the Smart Array 6404 Controller has been created. # /opt/raidsa/bin/ciss_insf Installing special file for Smart Array 6404 /dev/ciss3 installed # Step 5. At the prompt enter: loadfile -l INSTCMDS /opt/raidsa/bin/saconfig # loadfile -l INSTCMDS /opt/raidsa/bin/saconfig # Step 6. Configure the array(s) and logical drive(s) following the instructions for the saconfig configuration utility. The entire path /opt/raidsa/bin/saconfig /dev/cissx needs to be entered for saconfig to run. Step 7. Once the logical drive(s) and array(s) have been configured, exit the recovery shell by entering reboot at the prompt. The system will reboot and you will be returned to the Boot Console Handler (BCH) prompt. Step 8. At the BCH prompt, start Ignite-UX from the HP-UX 11i v1 Core OS Install and Recovery Media. The Ignite-UX Welcome screen displays (see Step 1). Step 9. Select Install HP-UX. 14 Chapter 1

15 Smart Array 6404 Controller HP-UX Installation Setting up a Smart Array 6404 Controller As a Boot Device Step 10. Select the kind of installation (Guided or Advanced) you want to do. The installation starts, and the Ignite-UX graphical interface (GUI) appears. Step 11. Under the Basic tab, select the configuration to use according to the HP-UX system you are using. Step 12. Still under the Basic tab, for the root disk for the installation, select the Smart Array 6404 logical drive you want to install the HP-UX operating system on. Step 13. Continue with (and finish) the installation as usual. Step 14. Once the installation has completed, you can boot from that Smart Array 6404 logical drive. Using ORCA (IA Platforms Only) This section describes how to use ORCA, a simple ROM-based configuration utility that runs on all Integrity Servers. For IA or Integrity systems follow this procedure: Configuring Your Logical Boot Drive When using an HP Smart Array controller as your boot controller, use the Option Rom Configuration for Arrays (ORCA) utility to configure your logical boot drive. The ORCA utility can only be accessed when the system is booting. Step 1. Press the F8 key when the prompt appears on the screen during boot to start ORCA and configure your logical boot drive. Step 2. Select the Create Logical Drive Step 3. Use the Arrow keys, Spacebar, and Tab key to navigate around the screen and set up the logical drive, including an online spare drive if one is required. NOTE You cannot use ORCA to configure one spare drive to be shared among several arrays. Step 4. Press the Enter key to accept the settings Step 5. Press the F8 key to confirm the settings and save the new configuration. After several seconds, the Configuration Saved screen is displayed. NOTE Pressing F8 at the ORCA prompt may not start ORCA on all terminals. If ORCA does not start when F8 is pressed, reboot and use esc 8 at ORCA prompt to start ORCA. Chapter 1 15

16 Smart Array 6404 Controller HP-UX Installation Setting up a Smart Array 6404 Controller As a Boot Device 16 Chapter 1

17 2 Smart Array 6404 Controller OpenVMS Installation Chapter 2 17

18 Smart Array 6404 Controller OpenVMS Installation Smart Array 6402 Controller Components Smart Array 6402 Controller Components Figure 2-1 Smart Array 6402 Controller Table 2-1 Item ID Controller Components Description 1 Internal SCSI connector, port A1* 2 Internal SCSI connector, port A2* 3 External SCSI connector, port A1* 4 External SCSI connector, port A2* 5 Controller battery 6 Battery-backed cache module 7 Connector for expansion board NOTE Do not use both the internal and external connectors on one port simultaneously. The card will not function if both connectors on one port are used. 18 Chapter 2

19 Smart Array 6404 Controller OpenVMS Installation Smart Array 6404 OpenVMS Installation Prerequisites Smart Array 6404 OpenVMS Installation Prerequisites Before installing the Smart Array 6404 controller, ensure that you have the following software and firmware: OpenVMS Version V8.2-1 (or later) for Integrity servers. TCP/IP Version 5.5 or later. Smart Array firmware Version 2.58 or later. Refer to the website to download Version 2.58 firmware. From the HP website, choose Software and Driver Downloads. Once on this page, enter the product number of your smart array controller, and choose Download Driver and Software (firmware). HP Insight Management Agents for OpenVMS V3.3 or later and any prerequisite software. Software documentation and downloads can be obtained from the following website: HP Array Configuration Utility (ACU-XE) for Integrity Servers Version 6.4 or later and any prerequisite documentation. Software documentation and downloads can be obtained from the following website: Also make sure that you review the following documentation: Check the Smart Array 6404 Release Notes available at in the IO Cards and Networking Software section for known problems or other information needed for installation. Confirm that the Smart Array 6404 controller and software are supported on the HP Integrity server and I/O slot chosen. Refer to the Smart Array 6404 Controller Support Matrix located in the IO Cards and Networking Software section for more information. Chapter 2 19

20 Smart Array 6404 Controller OpenVMS Installation Smart Array 6404 OpenVMS Quick Installation Smart Array 6404 OpenVMS Quick Installation Before installing a Smart Array 6404 Controller in a server, backup all data. This step is mandatory if the disks were not previously configured on a Smart Array Controller, because the data format will not be recognized and the existing data will not be preserved. Install Smart Array 6404 Controllers WARNING To reduce the risk of personal injury or damage to the equipment, consult the safety information and user documentation provided with your server before attempting installation. Many computers are capable of producing energy levels that are considered hazardous. These computers are intended to be serviced by qualified personnel trained to deal with those hazards. Do not remove enclosures or attempt to bypass any interlocks that may be provided for the purpose of removing these hazardous conditions. CAUTION Electrostatic discharge (ESD) can damage electronic components. Be sure that you are properly grounded before continuing the installation procedure. The Smart Array Controllers contain electronic components that can easily be damaged by small amounts of static electricity. To avoid damage, follow these guidelines: Store the controller in its antistatic plastic bag until you are ready to install it Work in a static-free area, if possible Handle the controller only by the edges. Do not touch electronic components or electrical traces If you must lay the controller down, place it on a non-conductive mat or surface Before beginning installation, and without removing the Smart Array Controller from its antistatic bag, inspect the controller for any signs of obvious damage, such as chipped or loose components. Contact HP if the controller is damaged. Installing the Controller for External Storage The controller comes pre-configured. You do not have to set any jumpers or connectors. CAUTION In systems using external data storage, be sure that the server is the first unit powered down and the last unit to be powered back up. Doing this ensures that the system will not erroneously mark the disk drives as failed. NOTE Do not connect a SCSI cable to an external SCSI port without either disabling the card using OLAR or powering down the system. Adding the SCSI cable by hot-plugging it can cause bus errors, or possibly the controller to lock up, and in rare cases, electrical damage. 20 Chapter 2

21 Smart Array 6404 Controller OpenVMS Installation Smart Array 6404 OpenVMS Quick Installation Step 1. Access the system controller bay If the system is running, shut it down. Wait for the system to shut down completely, and then power off the system. Open the system to gain access to the PCI backplane. For better performance, insert the controller into the fastest performance PCI slot available. Step 2. Install the controller Slide the controller edge-connector into the PCI slot until it is fully seated. Secure the controller and reassemble the system. Connecting Controller For Internal Storage This section provides information on how to connect the Smart Array 6404 controller for internal storage. For more information on cable routing review the latest edition of the Smart Array (A9891A) Cable Routing on docs.hp.com. Step 1. Power down the system and open any access panels and covers giving you access to the internal SCSI cabling and the PCI slots. Step 2. Install the Smart Array PCI-X RAID card (A9891A) in a full-length PCI slot. There may be a specific slot required on your server, please see your server documentation for details. Step 3. Remove the SCSI cable(s) connecting the internal disks to the built-in SCSI controller. Step 4. Route the new SCSI cables(s) from the internal disks to the Smart Array cards. Step 5. Replace access panels and covers CAUTION Do not operate the server for long periods without the access panel installed. Operating the server without the access panel results in improper airflow and improper cooling that can lead to thermal damage. WARNING To reduce the risk of personal injury or damage to the equipment, consult the safety information and user documentation provided with your server before attempting installation. Many computers are capable of producing energy levels that are considered hazardous. These computers are intended to be serviced by qualified personnel trained to deal with those hazards. Do not remove enclosures or attempt to bypass any interlocks that may be provided for the purpose of removing these hazardous conditions. Chapter 2 21

22 Smart Array 6404 Controller OpenVMS Installation Smart Array 6404 OpenVMS Software Installation Smart Array 6404 OpenVMS Software Installation Installing the Smart Array Controller to a System Running OpenVMS Step 1. Install the controller according to the instructions in the section titled Install Smart Array 6400 Controller. Step 2. Make sure your Smart Array firmware is Version 2.58 or later. Refer to the website to download Version 2.58 firmware. From the HP website, choose Software and Driver Downloads. Once on this page, enter the product number of your smart array controller, and choose Download Driver and Software (firmware). Step 3. Web based utilities are provided for monitoring and configuring the smart array controller and the attached storage running with OpenVMS. The monitoring function is made available as part of the HP Insight Management Agents kit for OpenVMS Version 3.3. After you have installed the controller, you need to install HP Insight Management Agents for OpenVMS V3.3. Software documentation and downloads can be obtained from the following website: Step 4. Online controller array configuration and maintenance functions are provided using the SA6400A Array Configuration Utility for Smart Array Controllers (ACU-XE) Version 6.4. The ACU-XE utility is installed separately from the HP Insight Management Kit, but requires the facilities provided by the Management kit. You can download the HP Array Configuration Utility for Integrity Servers Version 6.4 from the following website: The Smart Array Configuration Utility is fully compatible with HP Insight Management Agents for OpenVMS Version 3.3. Installing the Smart Array Controller as a Boot Device Use the following steps to install the smart array controller prior to installing the operating system. When using an HP Smart array controller as your boot controller, use the Option Rom Configuration for Arrays (ORCA) utility to configure your logical boot drive. The ORCA utility can only be accessed when the system is booting. Refer to the Section below titled Using Orca for instructions on how to use this ROM-based utility. Step 1. Power down the system. Step 2. Install the controller according to the instructions in the section titled Install Smart Array 6400 Controller. Step 3. Power up the system. Step 4. During initialization verify that your firmware is at If you need firmware Version 2.58, refer to the website to download Version 2.58 firmware, and choose Software and Driver Downloads. Enter the product number for your smart array controller and choose Download Driver and Software (firmware). Step 5. Start the Orca program. See the Section (below) titled Using Orca. Step 6. Exit out of Orca after configuring drives. The system will continue to initialize other devices in the system. 22 Chapter 2

23 Smart Array 6404 Controller OpenVMS Installation Smart Array 6404 OpenVMS Software Installation Step 7. Once you are at the Boot menu, you are ready to install OpenVMS. Refer to the HP OpenVMS Upgrade and Installation manual for complete instructions on installing OpenVMS Version The drivers for the smart array 6404 and 6404 controllers are included in the OpenVMS Version software. Step 8. After installing OpenVMS, install HP TCP/IP Version 5.5 or later, which is included on your OpenVMS media. Step 9. Web based utilities are provided for monitoring and configuring the smart array controller and the attached storage running with OpenVMS. The monitoring function is made available as part of the HP Insight Management Agents kit for OpenVMS Version 3.3. After you have installed the controller and OpenVMS, you need to install HP Insight Management Agents for OpenVMS V3.3. Refer to the following website for the Insight Management Agents Version 3.3 software downloads and documentation on how to monitor the smart array: Step 10. Online controller array configuration and maintenance functions are provided using the SA6400A Array Configuration Utility for Smart Array Controllers (ACU-XE) Version 6.4. The ACU-XE utility is installed separately from the HP Insight Management Kit, but requires the facilities provided by the Management kit. You can download the HP Array Configuration Utility for Integrity Servers Version 6.4 from the following website: The Smart Array Configuration Utility is fully compatible with HP Insight Management Agents for OpenVMS Version 3.3. Chapter 2 23

24 Smart Array 6404 Controller OpenVMS Installation Using ORCA Using ORCA This section describes how to use ORCA, a simple ROM-based configuration utility that runs on all operating systems. ORCA Limitations For the most efficient use of drive space, do not mix drives of different capacities within the same array. The configuration utility treats all physical drives in an array as if they have the same capacity as the smallest drive in the array. The excess capacity of any larger drives is wasted because it is unavailable for data storage. The probability that an array will experience a drive failure increases with the number of physical drives in the array. If you configure a logical drive with RAID 5, keep the probability of failure low by using no more than 14 physical drives in the array. Configuring Your Logical Boot Drive When using an HP Smart Array controller as your boot controller, use the Option Rom Configuration for Arrays (ORCA) utility to configure your logical boot drive. The ORCA utility can only be accessed when the system is booting. NOTE When using terminal emulators that do not correctly map to the function keys, press Esc 8 keys, instead of the F8 key to enter the configuration utility after the Smart Array banner is displayed. Step 1. Press the F8 key when the prompt appears on the screen during boot to start ORCA and configure your logical boot drive. Step 2. Select the Create Logical Drive Step 3. Use the Arrow keys, Spacebar, and Tab key to navigate around the screen and set up the logical drive, including an online spare drive if one is required. NOTE You cannot use ORCA to configure one spare drive to be shared among several arrays. Step 4. Press the Enter key to accept the settings Step 5. Press the F8 key to confirm the settings and save the new configuration. After several seconds, the Configuration Saved screen is displayed. NOTE Newly created logical drives are invisible to the operating system. To make the new logical drives available for data storage, format them using the instructions given in the operating system documentation. 24 Chapter 2

25 Smart Array 6404 Controller OpenVMS Installation Issues and Restrictions Issues and Restrictions Issues and Restrictions Awareness In order to use the smart array controllers, A9890A and A9891A, with OpenVMS, you must ensure that your smart array controllers are running Version 2.58 firmware. Refer to the website to download Version 2.58 firmware. From the HP website, choose Software and Driver Downloads. Once on this website, enter the product number of your smart array controller, and choose Download Driver and Software (firmware). For smart array controller restrictions and limitations, review the HP Smart Array 6400 Series Controller Support Guide which can be found at the following website: When reporting errors or issues, the System Event Analyzer (SEA) in the WEBES diagnostic suite incorrectly identifies the SA6400 Smart Array cards as SA5304 cards. This will be corrected in a future release. Chapter 2 25

26 Smart Array 6404 Controller OpenVMS Installation Issues and Restrictions 26 Chapter 2

27 A Declaration of Conformance Appendix A 27

28 Declaration of Conformance Figure A Series Declaration of Conformance 28 Appendix A

29 Declaration of Conformance Figure A Declaration of Conformance Appendix A 29

30 Declaration of Conformance 30 Appendix A