Transcription

1 PORTABLE BELT CONVEYOR (Includes Tires / ZAM Galvanizing) TUBULAR HOUSING: - 10'' (25.4 cm) x 12 gauge (2.66 mm) galvanized BELT: - 15'' (38.1 cm) PVC Cresent pattern with slider bed backing HOPPER: - Spring supported canvas (collapsible with quick release handle) DISCHARGE SPOUT: - Black plastic with 12 (30.5 cm) round outlet HEAD END AND DRIVE BEARINGS: - 1 3/4 (44 mm) Ball, sealed DRIVE: - S-Drive on cresent face, lagged drive LENGTHS: - 60, 70 & 85 Models (18.29 m & m) WHEEL TREAD: - 60 Model (3.15 m), 70 Model ( 3.40 m), 85 Model (3.86 m) DRIVE CHOICES: - PTO, Electric LIFTING SYSTEMS: - Hydraulic cylinder on 60, 70 & 85 Models (18.29 m, m & m) (1) 4 x 24 on 60 Model, (1) 4 x 36 on 70 Model, (2) 4 x 24 on 85 Model RETURN BELT GUARDS: OPERATING ANGLE: OPERATING SPEED: CAPACITY: POWER REQUIRED: - Galvanized, Standard equipment - Up to 30 degrees of incline ft. ( m) per minute - Up to 6000 BPH (162 TPH). Capacity will decrease as operating angle increases Model - 15 HP (11 kw), 30 HP PTO 70 Model - 15 HP (11 kw), 40 HP PTO 85 Model - 20 HP (15 kw), 60 HP PTO - A belt conveyor will require less horsepower to move grain than a screw conveyor, perhaps only half the amount. OWNERSHIP ADVANTAGES:- Longer life. Up to 3 times the life of a comparable capacity screw conveyor. - Cleanout is complete limiting contamination between commodities. - Gentle handling of the crop, particularly at low belt speeds. Special Features of the Hutchinson/Mayrath Portable Belt Conveyor Galvanized tubular housing Standard galvanized return belt guards (wind guards) Larger 1 3/4 (44 mm) head and drive pulley bearings. Larger diameter 8 (20.3 cm) head pulley, 6 (15.2 cm) tail pulley and take-up pulley. Longer pulleys 18 (45.7 cm) for 15 (38.1 cm) wide belt. Minor misalignment does not cause belt damage. Belt is PVC cresent pattern that is resistant to stretching. Spring loaded belt tensioner on take-up pulley. Powder coat red paint on painted surfaces. Adjustable discharge spout. Adjustable return rollers to aid belt tracking. Adjustable hitch assembly for easier set-up. The maximum operating incline is 30 degrees. Capacity will decrease as the operating angle increases. If you would like assistance in determining the conveyor length you need, contact your dealer or the factory at

2 PORTABLE BELT CONVEYOR Shown in Transport Position Shown in Maximum Raised Position - What is the capacity of the belt conveyor? Generic Reference Only. Inclined Angle Belt Speed in FPM Capacity in BPH FPM ( m) 6000 BPH FPM ( m) 3300 BPH FPM ( m) 1750 BPH 03381A

3 PORTABLE BELT CONVEYOR (Includes Tires / ZAM Galvanizing) To order Hutchinson belt conveyors, add H, i.e. H10600B15P8; Mayrath use existing Catalog No. Belt Conveyor Complete with Power Take Off (PTO) Drive - with Tires Catalog No. Tube Diameter Length Weight List Price 10600B15P8 10 (25.4 cm) 60 (18.29 m) 3116 lbs. (1413 kg) 18, B15P8 10 (25.4 cm) 70 (21.34 m) 3522 lbs. (1598 kg) 20, B15P8 10 (25.4 cm) 85 (25.91 m) 5050 lbs. (2291 kg) 23, Add letter C to part no. for Belt Drive instead of Chain Drive, i.e B15PC8. Add $2, to List Price. Belt Conveyor Complete with Electric Motor Drive (Less Motor) - with Tires (Motor Pulley and bushing are included) Use 4.8 (12.2 cm) P.D. motor pulley for maximum capacity. Elec. Power No. of List Catalog No. Tube Diameter Length Required Belts Weight Price 10600B15E8 10 (25.4 cm) 60 (18.29 m) 15 HP (11 kw) lbs. (1448 kg) $18, B15E8 10 (25.4 cm) 70 (21.34 m) 15 HP (11 kw) lbs. (1632 kg) 20, B15E8 10 (25.4 cm) 85 (25.91 m) 20 HP (15 kw) lbs. (2291 kg) 24, Add letter C to part no. for Belt Drive instead of Chain Drive, i.e B15EC8. Add $2, to List Price. Optional Equipment Hydraulic Hoist Power Pack; 110 Volt (AC) Electric, (3 gallon capacity) - Catalog No., PP List Price $2, Portable Belt Conveyor Drive Change Over Kits Electric Drives include motor sheave, bushing and drive key. Catalog No. Description Weight - Pounds List Price D1015BP Drive Kit PTO 85 lbs. (39 kg) $ D1060BE Electric Drive for 60, 70 & 85 (18.29 m, m & m) 150 lbs. (68 kg) Rubber Belt Option - For operation below 20 F (-5 C) - Add R to Catalog No. ( i.e B15PR8 or 10600B15PCR8.) Add $15.00 per foot of conveyor to List Price, i.e. for 60 (18.29 m) conveyor, add $ NOTE: For additional accessories, see conveyor accessory pages in this section

4 36 & 50 (10.97 m & m) LOW PROFILE COMMODITY CONVEYORS (Includes Tires / ZAM Galvanizing) TUBULAR HOUSING: - 10'' (25.4 cm) x 12 gauge (2.66 m) galvanized w/full length wind guards BELT: - 15'' (38.1 cm) Rubber continuous chevron pattern with slider backing. - (PVC belt is optional.) RECEIVING HOPPER: - Low profile transfer hopper style with collapsible spring supported canvas DISCHARGE SPOUT: - Adjustable black plastic with 12 (30.5 cm) round outlet DRIVE FOR 36 MODEL: - Drive located at the head end with snub pulley; electric or hydraulic. DRIVE FOR 50 MODEL: - Electric S drive mounted in middle of conveyor. OPERATING SPEED: Feet per minute (235 mpm) for electric w/5.2 P.D. motor sheave CAPACITY: - Up to 5000 bph (135 tph); on electric drive model - Up to 4000 bph (108 tph); on hydraulic drive 36 model Capacity will decrease as operating angle increases. HORSEPOWER REQUIRED: - 10 HP (7.5 kw) - for 36 (10.97 m) model and 15 HP (11 kw) for 50 (15.24 m) model (30 HP PTO for Model 50). PRODUCT ADVANTAGES: - Gentle handling to maintain seed quality. - Exclusive belt alignment guide to maintain belt tracking. - Capable of handling commodity products. Ideal for receiving from bin unloaders. - Spring loaded belt take-up to keep constant tension on conveyor belt. On the 50 (15.24 m) model, a cogged belt drive option is available instead of the roller chain drive. To order, add the letter C to the catalog no., i.e. B10500ECR8. Add $2, to the List Price. PVC Crescent Top Conveyor Belt Option. Omit the R from the Catalog No., i.e. B10362EW8 or B10500E8. (PVC belts not recommended for operation below 25 F.) Deduct $ from list price for 36 (10.97 m) models and deduct $ from list price for 50 (15.24 m) models. To order Hutchinson belt conveyors, add H, i.e. HB10362ERW8 or HB10500ER8. Mayrath use existing catalog number, as shown above. LOW PROFILE COMMODITY CONVEYORS - with Tires Catalog No. Description Tube Dia. Length Weight List Price B10362ERW8-ES Electric 10 (25.4 cm) 36 (10.97 m) 2,290 lbs. (1039 kg) 15, B10362HRW8-ES Hydraulic 10 (25.4 cm) 36 (10.97 m) 2,225 lbs. (1009 kg) 16, B10500ER8 Electric 10 (25.4 cm) 50 (15.24 m) 2,900 lbs. (1315 kg) 18, B10500PR8 PTO 10 (25.4 cm) 50 (15.24 m) 3,080 lbs. (1397 kg) 19, *NOTE: If you wish to have the dual (hydraulic and electric) drive capability for the B10362ERW8-ES model, order the D10362H drive also. See page 5. NOTE: Electric motor is not included on electric drive models. Motor sheave, bushing and drive key are furnished. {Use a 10 HP (7.5 kw) motor on the 36 (10.97 m) model and a 15 HP (11 kw) motor on the 50 (15.24 m) model.} An optional 3.8 P.D. motor sheave & bushing is available on the 36 LPCC, which decreases the belt speed by approximately 200 feet per minute (60.96 meters per minute). The sheave Part No. is 3097A1 - List Price $ The bushing Part No. is 3086A1 - List Price $ An optional motor sheave is not available on 50 (15.24 m) models. NOTE: The 36 (10.97 m) hydraulic models do not include the hoses from the control valve to the tractor. A hydraulic drive 50 (15.24 m) model is not available. The 36 (10.97 m) hydraulic models require 15 gpm ( PSI (10342 kpa). NOTE: The older 36 (10.97 m) seed belt w/o the center take-up assembly can be updated with a center take-up. Order Catalog No CTP if the conveyor has a PVC belt; List Price $1, Order Catalog No CTR if the conveyor has a rubber belt; List Price $1,

5 36 & 50 (10.97 m & m) LOW PROFILE COMMODITY CONVEYOR 36 W/ELECTRIC DRIVE AT MAXIMUM INCLINE 50 W/ELECTRIC DRIVE AT MAXIMUM INCLINE 36 SHOWN IN TRANSPORT POSITION TREAD WIDTH FOR BOTH IS 9-5 (2.9 m) 50 SHOWN IN TRANSPORT POSITION LOW PROFILE COMMODITY CONVEYORS Drive Kits Catalog No. Description Weight List Price D10361E 36 (10.97 m) Electric Drive Kit 140 lbs. (64 kg) $ 1, D10361H* 36 (10.97 m) Hydraulic Drive Kit 215 lbs. (97 kg) $ 3, D10362H** 36 Hydraulic Drive Kit 100 lbs. (45 kg) $ 2, D10500P 50 (15.24 m) PTO Drive Kit 320 lbs. (146 kg) $ 2, D1060BE 50 Electric Drive Kit 150 lbs. (68 kg) $ * For units prior to Serial Number , use D10360H instead of D10361H. **If a customer requests to have both an electric and hydraulic drive installed at the same time on a B10362ERW-ES unit, then order Catalog No. D10362H. If a customer wants to convert a B10362ERW-ES and install a hydraulic drive and remove the electric drive, order Catalog No. D10361H. The change-over kits are for converting from one drive to the other. Electric drive kits do not include the electric motor. Motor sheave, bushing and drive key are provided. Hydraulic drive kits do not include the hoses from the control valve to the tractor. Hydraulic drives require 15 gpm ( PSI (10342 kpa). Optional Equipment NOTE: For additional accessories, see conveyor accessory pages in this section B B

6 BELT CONVEYOR TRANSFER HOPPER TUBULAR HOUSING: BELT: HOPPER: DISCHARGE SPOUT: WHEEL TREAD: DRIVE CHOICES: LIFTING SYSTEM: RETURN BELT GUARDS: OPERATING SPEED: CAPACITY: HORSEPOWER REQUIRED: OWNERSHIP ADVANTAGES: - 10'' (25.4 cm) x 12 gauge (2.66 mm) galvanized - 15'' (38.1 cm) PVC Crescent pattern with slider bed backing - Spring supported canvas - Black plastic (91.4 cm) - Electric or Hydraulic - Screw jack incorporated into carriage - Galvanized, Standard equipment ft.. ( m) per minute - Up to 6000 bushels per hour (162 TPH). Capacity will decrease as operating angle increases. - 5 HP (4 kw) electric - Requires 12 GPM (45 LPM) at 1000 PSI (6895 kpa) for hydraulic. - A belt conveyor will require less horsepower to move grain than a screw conveyor, perhaps only half the amount. - Longer life. Up to 3 times the life of a comparable capacity screw conveyor. - Cleanout is complete limiting contamination between commodities. - Gentle handling of the crop, particularly at low belt speeds. Special Features of the Hutchinson/Mayrath Belt Conveyor Transfer Hopper Galvanized tubular housing Standard galvanized return belt guards (wind guards) Longer pulleys for 15 (38.1 cm) wide belt. Minor misalignment does not cause belt damage. Belt is PVC cresent pattern that is resistant to stretching. Rubber belt option available for operating temperatures below 20 F (-5 C). Powder coat red paint on painted surfaces. Optional Features Available Adjustable undercarriage frame for optimum balance when maneuvering. Towable undercarriage with hitch and highway rated hubs, wheels and tires. Swing away package for use with Hutchinson and Mayrath portable belt conveyors A1 6

7 BELT CONVEYOR TRANSFER HOPPER Order drive choice, undercarriage, towing package and swing away package separately. Catalog No. Description Weight List Price B1015HR Mayrath basic hopper (Has rubber belt for operation below 20 F) 550 lbs. (249 kg) $5, HB1015HR Hutchinson basic hopper (Has rubber belt for operation below 20 F) 550 lbs. (249 kg) 5, E Electric motor drive. Includes motor mount, driven sheave, drive sheave, belts and guard. Does not include motor.* 95 lbs. (43 kg) H Hydraulic motor drive. Includes motor, connections to hopper, shielding and hoses. 45 lbs. (20 kg) 1, U Basic undercarrriage. Includes two 15 (38.1 cm) wheels for maneuvering, adjustable carriage and raising jack. 90 lbs. (41 kg) W Hopper end wheel package. Includes two hopper end wheels and mounting components. 30 lbs. (14 kg) W Caster End Wheel Kit (Wheels Swivel 360 F) 45 lbs. (20 kg) TU Towing package. Includes basic undercarriage with roadway wheels, tires and hitch. 120 lbs. (54 kg) 1, SA Swing away package. Includes two hopper end wheels with mounting components and discharge support system. (f/single Belts) 60 lbs. (27 kg) SA Swing-Away package with caster wheels 75 lbs. (34 kg) SA Swing Away package for adapting to LPCC Hopper 60 lbs. (27 kg) SA Swing away package for adapting to 10 (25.4 cm) Portable Grain Pump 60 lbs. (27 kg) SA Swing away package for Model 50 Mass-ter Mover 60 lbs. (27 kg) HS Hydraulic End Wheel Drive Kit f/hyd. Drive Transfer 185 lbs. (84 kg) 1, f/use with Single Belt Conveyors. (Must also order 1015H above.) PVC Belt Option - Remove R from Catalog No. (i.e. B1015H); Deduct $ from List Price. *Recommend a 5 HP (4 kw) motor. (See Item 1015E above.) 03425A1 7

8 DRIVE-OVER BELT CONVEYOR (Includes Tires) INCLINED TROUGH: - Flat bottom, troughed edges, 10 gauge (3.43 mm), 20 degree inclined angle. BELT: - 24'' (61.0 cm) PVC cresent pattern with slider bed backing, stainless steel belt splice and pin material. Rubber Belt option is not available. DISCHARGE SPOUT: - Adjustable angle with 16 x 21 (40.6 cm x 53.3 cm) rectangular outlet. DRIVE-OVER: - 5-1/2 (14.0 cm) clearance. 7 x 10 (2.13 m x 3.05 m) wide area. Ramps and dumping area a single unit. DRIVE: - S-Drive on cresent face of belt w/spring loaded take-up, lagged drive pulley. Conveniently located under the incline section. LENGTH: - Overall from hitch pin to spout end is 33-5 (10.19 m). DISCHARGE HEIGHT: - 3 feet 4 inches (10.2 m) DUMPING AREA: - Hopper sides 10 (3.05 m) long by 12 (30.5 cm) wide. Cable lift into position. UNDERCARRIAGE: - Rotating arm design using a hydraulic cylinder. DRIVE CHOICES: - Electric motor. Power take-off. Hydraulic motor. OPERATING BELT SPEED: feet ( m m) per minute CAPACITY: - Up to 10,000 bushels per hour (270 TPH). HORSEPOWER REQUIRED: - 10 HP (7.5 kw) electric. Hydraulic drive capacity minimum 20 gal./min ( PSI (12,066 kpa) (25 HP PTO). INCLINED LENGTH: - Standard incline section length is 64 (1.63 m). On stationary models, 5 (1.52 m) of additional length may be requested, which provides 20 (50.8 cm) of additional discharge height. OWNERSHIP ADVANTAGES: - Low drive-over clearance; only 5-1/2 (14.0 cm) high. - Extra wide 24 (61.0 cm) belt. - Smooth transition from horizontal to incline. - Optional greater discharge height. (Stationary models only) - Higher capacity with lower belt speeds. - PTO drive choice. - Undercarriage lift choices. - Receive from side dump wagons, as well as bottom dump and rear dump vehicles. - S type drive on return belt for greater drive efficiency and lower belt tension requirements. Includes snub pulley to give greater wrap at drive pulley for slip free operation. - Spring loaded belt take-up for lower operating belt tensions. - Guide roller assembly to keep belt tracking properly. - Walk across platform and handrail provided to cross conveyor. - Adjustable angle discharge spout. - Removable hitch tube. - Self cleaning wing type tail pulley. - Product surface area /2 (44.7 cm) wide. - Hopper shield dump width /2 (1.08 m). 8

9 DRIVE-OVER BELT CONVEYOR (Includes Tires) Catalog Drive Undercarriage List No. Type Lift Type Weight Price 24245E8 Electric Hydraulic Cylinder 3870 lbs. (1755 kg) $23, * 24245EH8 Electric Hydraulic Cylinder 3950 lbs. (1792 kg) 25, H8 Hydraulic Hydraulic Cylinder 3670 lbs. (1665 kg) 24, HV8 Hydraulic Hydraulic Cylinder 3700 lbs. (1678 kg 25, P8 PTO Hydraulic Cylinder 3720 lbs. (1687 kg) 23, NOTE: On electric drive models (24245E8), a hydraulic hand pump is provided for operation of the lift cylinder and a winch is provided to raise and lower the hopper panels. *The 24245EH8 electric drive model has a hydraulic power unit in place of the hand pump and winch. (Requires 230/460V, 3 PH, 50/60 Hz.) (1.3 GPM and 2 HP) To order Hutchinson belt conveyors, add H, i.e. H24245E8, Mayrath use existing Catalog No., as shown. NOTE: The optional control valve kit is provided on the 24245HV8 models. NOTE: On electric drives, the motor is not furnished. Motor sheave, bushing and drive key are furnished. A 10 HP (7.5 kw) 1750 RPM motor is required. (NOTE: For power recommendations on extended length stationary units, see page 12.) On hydraulic drives, the hoses to the hydraulic motor are not furnished. (See optional control valve kit on page 12.) On hydraulic lift undercarriages, the hoses to the cylinder are not provided. (See optional control valve kit on page 12.) For numbers listed without drive, select the desired drive from the options on the next page A

10 STATIONARY OPTIONS DRIVE-OVER BELT CONVEYOR OPTIONS Catalog List No. Description Weight Price 25243L00 Conveyor less ramps, drive & undercarriage 2400 lbs. $16, without incline section (1-6 discharge height) (1089 kg) 25243L05 Conveyor less ramps, drive & undercarriage 2690 lbs. 18, with 5-4 (1.63 m) incline section (3-4 discharge height) (1220 kg) 25243L10 Conveyor less ramps, drive & undercarriage 2960 lbs. 19, with 10-8 (3.25 m) incline section (5-2 discharge height) (1343 kg) 2524A Hopper panel lift kit (winch style) 20 lbs (9 kg) For these conveyor catalog numbers, select the desired drive from the table below. Discharge heights given are from bottom of main frame. (Not from top of pit.) DRIVE KITS POSSIBLE PIT CROSS SECTION (FOR NON PORTABLE MODELS) NOTE: For grating, see Mass-ter Mover Model 150, page 10, reference number 12. Catalog List No. Description Weight Price D2420E Electric drive kit (2-Belt) 140 lbs. (64 kg) $ D2421E Electric drive kit (3-Belt) for units with extended incline section 150 lbs. (68 kg) D2422E Electric drive kit (2-Belt) includes hyd. hand pump for axle lift 175 lbs. (79 kg) 1, (For portable units after Serial No ) D2420H Hydraulic drive kit 50 lbs. (23 kg) 2, D2420P PTO 80 lbs. (36 kg) Electric drive kit does not include motor, but does include motor sheave. {Use 5.0 (12.7 cm) P.D. 2 or 3-groove sheave.} For 25243L00 & 25243L05 models, a 10 HP (7.5 kw) 1750 RPM motor is required. For 25243L10 models, a 15 HP (11 kw) 1750 RPM motor is required. {Use 5.0 (12.7 cm) P.D. 3-groove sheave.} On hydraulic drive models, an optional control valve kit is available, which provides all hoses, fittings and valves to completely plumb the conveyors hydraulic system. NOTE: Does not include hoses from hydraulic power source to conveyor. To order specify catalog no. 2424H. List price is $ NOTE: For additional accessories, see conveyor accessory pages in this section.) PP0209 Hyd. Power Unit Retrofit Kit - List Price $2, (For Serial No and higher.) (230/460V, 3PH, 50/60 Hz)

11 Single Belts CONVEYOR ACCESSORIES Arc Axle Kits (Hub Mount Style) - with Tires Catalog Conveyor List No. Lengths Weight Price P3075A8 60 (18.29 m) 294 lbs. (134 kg) $3, & 85 (21.34 m & m) NOTE: P3075A8 Kits attach to 4-Bolt (5 Bolt Circle) or 5-Bolt (5-1/2 Bolt Circle) Hubs. Hub Mount Arc Axle Kit (For four, five or six bolt hubs) (Shown for four or five bolt hubs) Electric Drive Tractor Kit for Arc Axles Catalog No. A2031B1 A2031B2 Electric Drive Tractor Kits f/arc Axle Kits Listed above Volts 230/ /460 Phase 1 3 Fit on 60, 70 & 85 (18.29m, 21.34m & 25.91m) Single Belt Weight 250 lbs. (113 kg) 250 lbs. (113 kg) List Price $ 3, , Drive Over Conveyor Side Pull Undercarriage Kit Catalog List No. Weight Price 2424S 190 lbs. $2, (86 kg)

12 CONVEYOR ACCESSORIES Spout Liner Kit for Single and Low Profile Commodity Belt Conveyor Catalog No. Description Weight List Price N6402 Spout Liner 15 lbs. (7 kg) $ Field Repair Kits for Belting Catalog No. Description Weight List Price 1015AS-Set 15 (38.1 cm) Alligator Ready Set 1.0 lbs. (1 kg) $ AS-Set 24 (61.0 cm) Alligator Ready Set 1.5 lbs. (1 kg) $ Includes the correct components for four belt connections, but no installation tool. (NOTE: to order the Belt Splice Installation Tool, specify Part No List Price - $ (NOTE: to order the Hand Skiver Tool, specify Part No List Price - $ Skiver is used to remove crescents or chevron top at area of splice application. Staple driver for belt splice. Part No List Price $ Belt Repair Sections Part Belt Belt Repair List No. Type Width Section Length Price PVC 15 (38.1 cm) 3 (91.4 cm) $ Rubber 15 (38.1 cm) 3 (91.4 cm) $ PVC 24 (61.0 cm) 3 (91.4 cm) $ NOTE: For alternate lengths consult factory for pricing. NOTE: Repair section comes complete with splice applied to each end and includes hinge pin and splice section for connecting into an existing belt as damage or wear requires. Belt Connection Clamp Tool (aids in pulling belt ends together) Cat. No. A1015BC List Price - $125.00, wt lbs. (8 kg). Single Belts Dolly Wheel Kits Catalog Conveyor List No. Lengths Weight Price 2014D 60, 70 & lbs. $ 1, (18.29 m, m & m) (36 kg) Single Belt Dolly Wheels

13 HORIZONTAL CUSTOM BELT CONVEYOR NOTE: These conveyors are not intended for placement under perforated bin floors, due to access needed for maintenance. They are also not intended for reversing drives. HOUSING: BELT: DRIVE: HORSEPOWER: LENGTH: BELT SPEEDS: CAPACITIES: - 10'' (25.4 cm) diameter x 6 (15.2 cm) deep u-trough sections. 14 gauge (1.9 mm) galvanized x 5 (1.52 m) long. Fully enclosed, slider pan belt return with rollers on 10 (3.05 m) centers. - 15'' (38.1 cm) PVC crescent pattern with slider bed backing. NOTE: A rubber belt option is available for low temperature operation {below 20 (-5 C)} - Double reduction belt drive through a jackshaft to the head shaft. Provides a wide range of operating speeds and horsepowers. All motor sheaves are included. - From 3 HP (2.2 kw) to 15 HP (11 kw) depending on capacity, belt speed and conveyor incline angle (up to 10 degrees allowable.) - From 16 to 131 (4.88 m to m) in 5 (1.52 m) increments. Maximum depends on power required , 600 or 800 feet ( m, m or m) per minute depending on desired capacity to 6600 bushels per hour (78 to 178 TPH) depending on belt speed and conveyor incline angle (up to 10 degrees). DISCHARGE SPOUT: - Adjustable angle metal with 12-5/8 (32.1 cm) wide x 15-3/4 (4.59 m) long bottom opening. FEATURES: - Gentle economical way to convey seed or commodity grain horizontally. Adaptable for use under hopper bottom storage To select the basic horizontal custom belt conveyor, the following must be determined. 1. The length of conveyor required. 2. The incline angle, if any, of the conveyor. 3. The desired capacity in bushels per hours. (Charts are based on dry corn.) From the horizontal custom belt conveyor catalog number table, select the catalog number for the desired conveyor length. NOTE: The last three numbers of the catalog number designate the nominal pulley center length of the conveyor in feet. From the motor selection chart for the appropriate incline angle (0, 5 & 10 degrees given), find a length of conveyor longer than the conveyor length required. Use the lowest conveyor belt speed that will give the desired capacity. For instance, using the zero degree incline table for a 101 foot (30.78 m) long conveyor that will handle up to 3300 bu/hr (89 tph), select the 131 foot (39.93 m) length. This will determine the motor horsepower that will provide the capacity and belt speed for the conveyor length {7-1/2 HP (5.5 kw) at 400 FPM (12.2 mpm) for this example}. From the drive catalog number table, select the catalog number for the selected motor horsepower and belt speed. The drive list price is found at the bottom of the horizontal custom belt conveyor catalog number table. Both a conveyor catalog number and a drive catalog number must be ordered. NOTE: In cases where the conveyor will always operate at capacities (bu/hr) lower than those listed in the motor selection chart, it may be possible to go with somewhat longer lengths. In such cases, consult the factory for recommendations. In no case, will conveyors longer than 131 (40 m) be provided. 13

14 HORIZONTAL CUSTOM BELT CONVEYOR (Based on conveyor operating at capacities listed) * NOTE: In cases where the conveyor will always operate at capacities (bu./hr.) lower than those listed in the motor selection chart, it may be possible to go with somewhat longer lengths. In such cases, consult the factory for recommendations. In no case, will conveyors longer than 131 (40 m) be provided. *NOTE: Electric motors are NOT provided C

15 HORIZONTAL CUSTOM BELT CONVEYOR For the optional gated inlet, order Catalog No. UB01001 and specify quantity desired. (Wt. 47 lbs.) List Price is $ each. For the optional collapsible canvas inlet hopper, order Catalog No. UB (Wt. 22 lbs.) List price $ For Rubber Belt, add R to conveyor catalog number, i.e. UB150016R. Add $15.00/ft. of conveyor, i.e., add $ for UB150016R. (For operation below 20 F.) In conveying applications where inadvertant stoppage or slowing down of a conveyor may damage the conveyor or upstream equipment feeding it, there is a speed monitoring device available. Consult factory for pricing and information. To prevent damage due to a plugged discharge chute or spout, there is a plugged chute device available. Consult factory for pricing information. It is strongly recommended that some type of speed monitoring device be installed to prevent damage to the conveyor or upstream equipment feeding it. It is also recommended to install some type of plugged switch in the discharge weldment spout of the conveyor. Hutchinson/Mayrath offers this type of equipment (See page 17 for information, part numbers and pricing. 15

16 HORIZONTAL CUSTOM BELT CONVEYOR A 16

17 HORIZONTAL CUSTOM BELT CONVEYOR Part No Speed Switch List Price $ Part No Digital Tachometer List Price $ Part No Bin Switch List Price $ Part No Standard Mount List Price $ Part No Whirligig Target List Price $ Part No NEMA 4 Enclosure List Price $ Part No Side Mount Plate List Price $ Part No Conduit Adapter List Price $

18 040113A 18