5 axle Lowbed Semitrailer with Automatic Steering Model ST L3. (Lowbed length approx. 14,000 mm) Technical Specification no.

Transcription

1 5 axle Lowbed Semitrailer with Automatic Steering Model ST L3 (Lowbed length approx. 14,000 mm) Technical Specification no. ST L3 06/02

2 5 axle Lowbed Semitrailer with automatic steering Model ST L3 Technical Data: (refers to vehicle s basic equipment) Max. speed resulting from tyre & axle capacity approx. km/h 80 Technical fifth wheel load approx. kg 23,000 Axle load: rigid axle approx. kg (x 2) 14,000 Automatically steered axle approx. kg (x 3) 14,000 Total axle load approx. kg 70,000 Total weight approx. kg 93,000 Tare weight acc. to DIN approx. kg 23,000 Payload acc. to DIN approx. kg 70,000 Total length approx. mm 19,900 Total width approx. mm 3,500 Total height unladen approx. mm 3,850 Length gooseneck over fifth wheel inclination of gooseneck approx. mm 4,070 Width approx. mm 960 Lowbed length approx. mm 14,000 + Rear inclination approx. mm 1,540 Frame height laden approx. mm 1,500 Road clearance underneath platform approx. mm 950 Road clearance underneath axles approx. mm 470 / 370 Road clearance underneath supports approx. mm 590 Road clearance underneath landing gear approx. mm 630 Road clearance underneath tool box approx. mm 680 Wheelbase (fifth wheel to middle of 3rd axle) approx. mm 13,550 Wheelbase of 5 axle assembly (axle 1 to axle 2) approx. mm 1,450 (axle 2 to axle 3) approx. mm 1,600 (axle 3 to axle 4) approx. mm 1,600 (axle 4 to axle 5) approx. mm 1,600 Length of ramps (undivided) approx. mm 2,900 Width approx. mm 600 Climbing angle approx. 18 all figures acc. to DIN KÖGEL Fahrzeugwerke AG Technical Specification no. ST L3 06/02

3 5 axle Lowbed Semitrailer with automatic steering Model ST L3 Technical description: (Subject to changes in construction) 1/2 Dimension/weights see tables page 2. Chassis frame Axles Axle assembly & steering Brakes Wheels & tyres Landing gears Ground plates for landing Spare wheel carrier Floor Extra reinforced dropped construction, made of high tensile steel sections, electrically welded, with I-type longbeams. Upper coupler and 3 1/2 king pin to SAE standards, screwed, adjustable steering wedge, slide plate. 2 axles with tapered roller bearings capacity 14,000 kg each at 80 km/h. 3 steered knuckled axles, capacity 14,000 kg each at 80 km/h. S-cam brakes with slack adjusters, brake size 420 x 200 mm, covered brake drums. Axles with hub connection according to those of truck tractor. 5 axle assembly with hydraulic axle load compensation (+200 / -160 mm) with rubber stopper on each axle for damping at maximum compensation (dual circuit system). 1st and 2nd axle rigid. 3rd, 4th and 5th axle hydraulically force-steered with one each double-acting cylinder. Steering via fifth wheel coupling with automatic turning limit stop. Re-adjustment and pre-stressing of steering by means of hand pump. Electrical display for one man axle tracking by means of a nitrogen-assissted pressure tank. Special-cylinders designed for extreme effect of dust and sand. Hydraulic oil filling by means of hand pump on right hand side. Axle suspension by means of HD-leaf springs made of high quality spring steel. Wheel track approx. 2,275 mm. Dual line air brake system with brake pressure coontrol device, diaphragm-type brake cylinders, parking brake system with spring loaded brake cylinders acting on 1st and 2nd axles. 2 coupling heads for brake and reserve air, NATO compatible. Facility to brake when tractor is separated accidentally and brake connections are cut off. 10 detachable disc wheels with mounted 10 tubes and tyres 24-21, Model XZL tubeless, make MICHELIN + 1 complete spare wheel, make MICHELIN. Mechanically operated, foldable landing legs, designed for full load. Operation from right hand side. 2 ground plates, approx. 500 x 500 mm, for smooth underground to either use land gears in front of gear folding supports at rear. 2 units, mounted on gooseneck on left and right hand side above fifth wheel, suitable for 24-20,5 tyres (one unit for lowbed, plus one unit for tractor), with one detachable lifting device with winch. Lowbed, inclination and ramps of 6 mm checkered steel plates, above steering axles of 8 mm checkered steel plates. Crossbars welded on inclination and ramps as drive-up support. Ramps Lashing rings 2 pcs undivided, hinged ramps, 600 mm wide, with adjustable track width and spring-type lifters for one man operation. Max. outer width of ramps approx. 3,400 mm, minimum inner width approx. 1,700 mm. 6 pairs of lashing rings mounted as follows: 1 pair on gooseneck tensile force 125 kn 1 pair in front of lowbed tensile force 125 kn 2 pairs at centre of lowbed tensile force 80 kn 1 pair on lowbed at rear tensile force 125 kn 1 pair on rear inclincation tensile force 80 kn Diameters: Tensile force 125 kn = 26 mm Tensile force 80 kn = 22 mm Lashing Requirement for fastening of tanks considered to be loaded covers totally: equipment Position 1 4 units recovery tool for total 70 t Position 2 4 units special recovery tool for total 37 t four-courd chain (delivery scope of winch manufacturer) Electric equipment 2 three-chamber tailights, 2 marker lights on lowbed in front, 1 licence plate illumination, 1 convoy cross, Connection by means of plugs and junction lines, Electrical equipment for 24 Volt. KÖGEL Fahrzeugwerke AG Technical Specification no. ST L3 06/02

4 5 axle Lowbed Semitrailer with automatic steering Model ST L3 Technical description: (Subject to changes in construction) 2/2 Rope guides for rope winch Load fastening equipment Tool boxes On left and right hand side of gooseneck in front of platform. 2 each rope pulleys (=4 pcs) and 1 each rope pulleys (=4 pcs) On left side on top of gooseneck one rope pulley as well as 2 rope guide windows on frame above fifth wheel. On rear inclination: 1 rope pulley and 1 three-piece ope roller. 8 pcs. caterpillar guides. Distance by 100 mm adjustable each from 650 to 2,250 mm. Securing by means of spring plugs. 4 sheeve blocks in front and centre of lowbed, width approx. 600 mm, wedge approx. 30, adjustable by 5 x 100 mm to insert. Securing by means of spring plugs to limit the loaded vehicle towards the front. 4 sheeve blocks with tension spindle and corresponding openings in lowbed to limit the loaded vehicle towards the back. 3 between both longitudinal members in front of platform, lockable. Dimensions: Front Middle Rear (approx) Depth 700 mm 700 mm 1,200 mm Width 700 mm 700 mm 700 mm Height 400 mm 400 mm 300 mm Accessories Paintwork Identification plates Trailer design 2 in driving direction on right hand side, lockable. Dimensions: Front Rear (approx) Depth 900 mm 600 mm Width 800 mm 600 mm Height 600 mm 600 mm With bearing for 2 lifting jacks. Each side four orange reflectors 2 red triangular reflectors at rear 1 bracket for one-line licence plate at rear, 2 folding supports at rear, 4 wheel chocks with holders, 2 hydraulic jacks with 25 t capacity each, tools for axles and wheels, 1 wheelnut wrench, spiral hoses for brake and reserve-air. Steel parts sandblasted with 2 primary undercoating of Epoxy Zinc and 2 final Epoxy layers of dark sand colour, non-reflective in accordance with NATO regulations. Total layer thickness approx. 120µ, RAL Maker s name in German / English with identification of axle loads. Figures for tyre pressure, for centre of gravity etc., painted to the trailer. Suitable for the transport of 1 tank with 70 tons, or 2 tanks with max. 35 tons each and a total length of approx. 7,100 mm each. KÖGEL Fahrzeugwerke AG Technical Specification no. ST L3 06/02

5 KÖGEL 5 axle Special Lowbed Semitrailer Type ST L3 Offroad operation / 3 steering axles KÖGEL Fahrzeugwerke AG Pictures ST L3

6 KÖGEL 5 axle Special Lowbed Semitrailer Type ST L Air pumping tyres KÖGEL Fahrzeugwerke AG Pictures ST L3

7 KÖGEL 5 axle Special Lowbed Semitrailer Type ST L3 Offroad operation KÖGEL Fahrzeugwerke AG Pictures ST L3

8 KÖGEL 5 axle Special Lowbed Semitrailer Type ST L3 KÖGEL Fahrzeugwerke AG Pictures ST L3