Volkswagen Touareg - Anti-Theft Alarm Sy Стр. 1 из 5 96-10 Anti-Theft Alarm System General information Anti-theft alarm system functions are integrated with those of the Comfort System Central Control Module J393 Access/Start Control Module J518 transmits Information on activating and deactivating the anti-theft alarm to J393 via the Comfort System CAN-Bus. Should the anti-theft alarm system be triggered, the alarm source is stored in Comfort System Central Control Module J393 and can be checked 97-5, Comfort System Central Control Module J393 - Alarm sources, checking. Before troubleshooting or servicing, technicians must be familiar with the functions and operation specifics of the parking aid system. Always read the owners manual and review applicable system functions. Additional information: Owners Manual Self Study Program - Course Number 89E303 "The Touareg" Self Study Program - Course Number 89J303 "The Touareg Electrical System Design and Function" Wiring Diagrams Component Locations Anti-theft alarm system, activating and deactivating When vehicle is equipped from the factory with antitheft alarm system and trailer hitch package, the trailer can be integrated with the anti-theft alarm system 96-10, Trailer, integrating with anti-theft alarm system.
Стр. 2 из 5 Anti-theft alarm system is automatically switched on by locking the vehicle. Anti-theft alarm system is then activated immediately. In order to prevent anti-theft alarm system from triggering unnecessary alarms, close all windows and doors before locking the vehicle. Ant-theft alarm system, deactivating: Anti-theft alarm system is deactivated when the vehicle is unlocked via the unlock button on radiofrequency remote control, or when vehicle is opened with keyless access, or when the ignition is switched on. Unlocking vehicle mechanically (emergency opening) - Unlock vehicle at drivers door. Anti-theft alarm system remains activated, however no - Switch on ignition within 15 seconds. If the ignition is not switched on after 15 seconds the By switching on the ignition, the electronic immobilizer recognizes a valid vehicle key and deactivates the antitheft alarm system. Trailer, integrating with anti-theft alarm system When vehicle is equipped from the factory with anti-theft alarm system and trailer hitch package, the trailer can be integrated with the anti-theft alarm system. - Ensure trailer plug is securely connected to vehicle trailer wiring plug. - Lock vehicle.
Стр. 3 из 5 Anti-theft alarm system is then activated immediately. Trailer is now integrated with anti-theft alarm system. Alarm will be activated should trailer wiring be disconnected from vehicle trailer wiring plug. Anti-theft alarm system is deactivated when the vehicle is unlocked via the unlock button on radiofrequency remote control, or when vehicle is opened with keyless access, or when the ignition is switched on. Unlocking vehicle mechanically (emergency opening) - Unlock vehicle at drivers door. Anti-theft alarm system remains activated, however no - Switch on ignition within 15 seconds. If the ignition is not switched on after 15 seconds the By switching on the ignition, the electronic immobilizer recognizes a valid vehicle key and deactivates the antitheft alarm system. Alarm Horn H12, servicing Alarm Horn H12 is located at left in plenum chamber, beneath E-Box. Alarm Horn H12, removing and installing Special tools, testers and auxiliary items required
Стр. 4 из 5 Torque Wrench 5-50Nm VAG1331 (or 5-50 Nm equivalent) To remove the Alarm Horn H12 (Back-up horn), antitheft alarm system must be deactivated. Removing: Caution! Switch off all electrical consumers. Switch off ignition and remove ignition key. - Remove E-box in plenum chamber at left 97-4, Electronics box in left plenum chamber, removing and installing. - Remove bolt - 1 -.
Стр. 5 из 5 - Disengage connector - 2 - and disconnect it from Alarm Horn H12-1 -. Installing: Install in reverse order of removal, noting the following: If self-locking nut - 3 - has been loosened in order to remove bracket - 2 -, it must be replaced. - Torque all bolts and nuts according to value in table 96-11, Alarm Horn H12, tightening torques:. Alarm Horn H12, checking Alarm Horn H12, function can be checked using Comfort System Central Control Module J393 On Board Diagnostic (OBD) program function "Output Diagnostic Test Mode (DTM)" 97-5, Comfort System Central Control Module J393, Output Diagnostic Test Mode (DTM).