METROLOGIC INSTRUMENTS, INC. MetroSelect Configuration Guide

METROLOGIC INSTRUMENTS, INC. MetroSelect Configuration Guide

Copyright 2005 by Metrologic Instruments, Inc. All rights reserved. No part of this work may be reproduced, transmitted, or stored in any form or by any means without prior written consent, except by reviewer, who may quote brief passages in a review, or provided for in the Copyright Act of 1976. Products and brand names mentioned in this document are trademarks of their respective companies.

TABLE OF CONTENTS Introduction Symbol Key... ix Bar Code Configuration Methods Single-Code Method... x Multi-Code Method... x Need to Start Over? Recall Defaults... xi Section A: Code Types and Decode Rules UPC/EAN...1 Code 128...3 Code 39...4 Interleaved 2 of 5...6 Standard 2 of 5...9 Other 2 of 5 Codes...10 Codabar...12 Code 93...13 Code 11...13 Telepen...14 Plessey Codes...15 Other Decode Features...17 Configurable Code Lengths...18 RSS 14 Features...21 RSS Limited Features...23 RSS Expanded Features...25 Section B: Supplements Two Digit Supplements/Redundancy...1 Five Digit Supplements/Redundancy...1 Supplements Required/Not Required...2 Remote Supplemental Requirement...2 Bookland (978) Supplement Required...3 977 (2 Digit) Supplement Required...3 Table of Contents iii

Table of Contents iv TABLE OF CONTENTS 378/379 French Supplement Requirement...3 434/439 German Supplement Required...4 414/419 German Supplement Required...4 # System 2 Requires Supplements...4 # System 5 Requires Supplements...5 8711685 Requires 5-Digit Supplements...5 Coupon Code 128...5 Code 128 Group Separators...6 Code 128 ]C1 Extended Code Format...6 100 msec to Find Supplemental...6 200 msec to Find Supplemental...6 400 msec to Find Supplemental...7 Code ID s with Supplements...7 Allow 2/5 on 977 Bar Code...7 Allow 2 on 977 Bar Code...7 Beep Once/Twice on Supplements...8 ISBN Check Digit Transmission...8 Bookland to ISBN Conversion...9 ISBN Re-Formatting...9 ISSN Check Digit Transmission...10 ISSN Re-Formatting...10 977 to ISSN Conversion...10 Number System 4 Coupon Code 128...11 UPC Discard...11 Supplements and UPC in Same Line...11 Section C: Communications Enable RS-232...1 Load Keyboard Wedge Defaults...1 Enable Light Pen/Wand Communication...1 Enable Keyboard Wedge Emulation...1 Enable Stand-Alone Keyboard Scanner...1 Load OCIA Defaults...2 Enable OCIA Output...2

TABLE OF CONTENTS Load IBM 46xx Defaults...2 Enable IBM 46xx Communication...2 Low Speed USB...3 Enable No Communication Mode...3 Reserved...3 Section D: Scanner Operation Configuration Mode Options...1 Scan Buffers...2 Redundant Scans...4 Miscellaneous Decode Features...6 Depth of Field Adjustments...7 Same Symbol Time Outs...8 Barcode Absence...9 LED Options...10 Beeper Options...12 Inter-Character Data Transmission Delays...17 Inter-Record Data Transmission Delays...18 Communication Time Out Options...19 Host Scanner Commands...21 Power Save Modes...26 Japanese Double Field Support...30 Test Modes...35 Section E: Prefixes/Suffixes Configurable Prefixes, All Data...1 Configurable ID Characters, Code Specific...3 Identifiers Character...3 Standard Prefix Characters...8 Standard Suffix Characters...14 Longitudinal Redundancy Check (LRC)...16 Configurable Suffixes, All Data...17 Special Formats...20 Character Replacements...21 Table of Contents v

Table of Contents vi TABLE OF CONTENTS Section F: Code Formatting UPC/EAN...1 Codabar...5 Code 39...7 Code 11...9 Telepen...9 Plessey...10 2 of 5...12 Section G: RS-232 Enable RS-232 Mode...1 Parity Features...2 Baud Rates...3 Data/Stop Bits...5 Hardware Handshaking...6 Software Handshaking...9 Miscellaneous...12 Section H: Keyboard Enable Keyboard Emulation...1 Country/Scan Code Table Selects...2 Keyboard/System Type...4 Special Keyboard Features...5 Inter-Scan Code Delays...9 Control Sets...10 3151 Terminal Keyboard...12 Section I: OCIA Load OCIA Defaults...1 Enable OCIA...1 DTS/Siemens...1 DTS/Nixdorf...1 NCR-S...1 NCR-F...1

TABLE OF CONTENTS Section J: Light Pen/Laser Emulation Enable Light Pen Mode...1 Space/Bar Height...1 Transmit Code 39...1 Transmit as Scanned...1 Poll Light Pen Source...2 Light Pen Extra Toggle...2 10x Narrow Element Border...2 50x Narrow Element Border...2 Set Narrow Element Width...3 Laser Emulation...3 Section K: IBM 46xx Configuration Enable IBM 46xx Communication...1 Load IBM 46xx Defaults...1 IBM Ports...1 IBM Reserve Codes...2 Section M: Code Bytes Code Byte Usage...1 Code Bytes 0-5...2 Code Bytes 6-9...3 Reserved Codes...4 Code Byte/Code Type Table...5 ASCII Reference Table...6 Extended Key Code Reference Table...11 Section N: Miscellaneous Features Custom Defaults...1 Serial Program Mode...4 Software/Serial Number...4 Section O: Auxiliary Port Controls Disable AUX Port...1 Table of Contents vii

Table of Contents viii TABLE OF CONTENTS AUX Port and Secondary Device Data Formats When Using a Metrologic Device as a Secondary...1 When Using a Non-Metrologic RS-232 Device as a Secondary...3 Additional AUX Port Data Formats...4 AUX Port Baud Rates...6 AUX Port Parity...8 AUX Port Stop/Data Bits...9 Enable/Disable RTS/CTS Handshaking...10 Message AUX RTS/CTS...10 Character AUX RTS/CTS...10 Enable/Disable Port Mode 7...10 Enable/Disable D/E Commands...11 Enable/Disable F/L Commands...11 Enable/Disable M/O Commands...11 Enable/Disable XON/XOFF Handshaking...12 Enable/Disable ACK/NAK...12 AUX CTS/RTS Polarity...13 AUX Same Symbol Timeout...13 Main Output Port Auxiliary Data Formats...14 Inter-Character Delays...16 Section P: USB Full Speed USB...1 Low Speed USB...4 Section R: IS3480 / MS3580 / MS3780 Button Modes...1 Button Click Delay...1 Primary and Secondary Scan Patterns...2 Sweet Spot Mode (IS3480)...3 CodeGate (IS3480 / MS3580)...3 Depth of Field...3 IR Activation...4 TTL RS232...4 CodeGate (MS3780)...5

INTRODUCTION Your new scanner has been configured at the factory with a set of default communication protocols. Since many host systems have unique formats and protocol requirements, Metrologic provides a wide range of configurable features that may be selected with the use of this bar code configuration guide. Once the configuration is completed, the scanner stores the settings in nonvolatile memory or NOVRAM. NOVRAM saves the settings when the power is turned off. Symbol Key * (asterisk) Default Feature ~ (tilde) Feature requires the Multi-Code Configuration Method, see Bar Code Configuration Methods on page x. Important! Note Introduction ix

Bar Code Configuration Methods x BAR CODE CONFIGURATION METHODS Metrologic scanners can be bar code configured in two ways: the Single-Code Method and the Multi-Code Method. Single-Code Method Most features can be enabled or disabled using the Single-Code Method. 1. Power up the scanner. 2. Scan the bar code(s) for the desired feature(s). 3. Observe a multi-toned, save setting beep that indicates the configuration has been saved to NOVRAM. Multi-Code Method All features can be enabled or disabled using the Multi-Code Method. A feature marked with a ~ requires the Multi-Code Method. 1. Power up the scanner. 2. Scan the Enter/Exit Configuration Mode bar code. [3 beeps] 3. Scan the bar code(s) for the desired feature(s). [1 beep] 4. Scan the Enter/Exit Configuration Mode bar code [3 beeps] and save new configuration. Enter/Exit Configuration Mode ³ 9 9 9 9 9 9 To abort a configuration change, power off the scanner before scanning the Enter/Exit Configuration Mode bar code.

NEED TO START OVER? Scan the Recall Default bar code. This will erase all previous settings and return to the scanner s default communications protocol. Keyboard Wedge interface scanners will load keyboard wedge defaults. All other scanners will load RS-232 defaults. Metrologic manufactures custom OEM scanners, which load the OEM s defaults. For further information on the affects they have on Metrologic default communications protocols refer to Section N, Custom Defaults. Recall Defaults ³ 9 9 9 9 9 8 Need to Start Over? xi

SECTION A UPC/EAN * Enable UPC/EAN Disable UPC/EAN ³ 1 0 0 1 1 6 ³ 1 0 0 1 0 6 * Enable UPC-A Disable UPC-A ³ 1 0 0 2 1 6 ³ 1 0 0 2 0 6 * Enable UPC-E Disable UPC-E ³ 1 0 0 2 1 0 ³ 1 0 0 2 0 0 Code Types & Decode Rules A 1

Code Types & Decode Rules A 2 SECTION A UPC/EAN * Enable EAN-13 Disable EAN-13 ³ 1 0 0 2 1 1 ³ 1 0 0 2 0 1 * Enable EAN-8 Disable EAN-8 ³ 1 0 0 2 1 4 ³ 1 0 0 2 0 4 * Enable Auto Redundancy UPC-E Disable Auto Redundancy UPC-E ³ 1 0 1 1 0 4 ³ 1 0 1 1 1 4

SECTION A CODE 128 * Enable Code 128 Disable Code 128 ³ 1 0 0 1 1 3 ³ 1 0 0 1 0 3 Enable UCC/EAN-28 ]C1 Code Formatting Disable UCC/EAN-128 ]C1 Code Formatting ³ 1 0 0 3 1 4 ³ 1 0 0 3 0 4 For Coupon Code 128, see Section B, page 5. Code Types & Decode Rules A 3

Code Types & Decode Rules A 4 SECTION A CODE 39 * Enable Code 39 Disable Code 39 ³ 1 0 0 1 1 1 ³ 1 0 0 1 0 1 Enable MOD 43 Check on Code 39 * Disable MOD 43 Check on Code 39 ³ 1 0 0 2 1 3 The scanner will only scan Code 39 bar codes that have a valid Modulo 43 check digit. ³ 1 0 0 2 0 3 The scanner will not test Code 39 bar codes for a modulo 43 check digit. Transmit Mode 43 Check Digit on Code 39 * Do Not Transmit Mode 43 Check Digit on Code 39 ³ 1 0 7 7 1 5 This feature works in conjunction with Mode 43 Check on Code 39. Both options must be enabled for this feature to work. ³ 1 0 7 7 0 5 This option will not transmit Code 39 s Mod 43 check character.

SECTION A CODE 39 Enable Full ASCII Code 39 * Disable Full ASCII Code 39 ³ 1 0 0 2 1 7 ³ 1 0 0 2 0 7 Enable PARAF Support (Italian Pharmaceutical Codes) * Disable PARAF Support ³ 1 0 0 2 1 5 The scanner will convert Code 39 bar codes to PARAF format. ³ 1 0 0 2 0 5 The scanner will not convert code 39 bar codes to PARAF format. Enable TRI-OPTIC Code * Disable TRI-OPTIC Code ³ 1 0 0 3 1 2 ³ 1 0 0 3 0 2 Code Types & Decode Rules A 5

Code Types & Decode Rules A 6 SECTION A INTERLEAVED 2 OF 5 * Enable Interleaved 2 of 5 (ITF) Disable Interleaved 2 of 5 (ITF) ³ 1 0 0 1 1 5 ³ 1 0 0 1 0 5 Enable MOD 10 Check on ITF * Disable MOD 10 Check on ITF ³ 1 0 0 3 1 0 The scanner will only scan Interleaved 2 of 5 (ITF) Bar codes that have a Modulo 10 check digit. ³ 1 0 0 3 0 0 The scanner will not test Interleaved 2 of 5 (ITF) bar codes for a Modulo 10 check digit. Transmit MOD 10 Check Digit on ITF * Do Not Transmit MOD 10 Check Digit on ITF ³ 1 0 7 7 1 4 The scanner transmits Interleaved 2 of 5 (ITF) MOD 10 check character. ³ 1 0 7 7 0 4 The scanner will not transmit Interleaved 2 of 5 (ITF) MOD 10 check digit characters. This feature works in conjunction with Mod 10 Check on ITF. Both must be enabled for this feature to work.

SECTION A INTERLEAVED 2 OF 5 Enable ALT Check Digit ITF * Disable ALT Check Digit ITF ³ 1 0 0 7 1 7 ³ 1 0 0 7 0 7 Enable 12 Digit ITF Check Digit at 1 * Normal Check Digit ³ 1 0 0 9 1 0 ³ 1 0 0 9 0 0 This feature requires MOD 10 ITF Check Digit to be enabled. The 12- character ITF check digit calculation will start with 1 instead of 0. Enable ITF/Code 39 Filter * Disable ITF/Code 39 Filter ³ 1 0 0 4 1 6 ³ 1 0 0 4 0 6 Supports Code 39/ITF filters. This feature may adversely affect reading Codabar, Code 93 and some other non-standard symbologies. Code Types & Decode Rules A 7

Code Types & Decode Rules A 8 SECTION A INTERLEAVED 2 OF 5 ~ ITF Symbol Length Lock 1 ~ ITF Symbol Length Lock 2 ³ 9 0 1 6 0 0 To specify a 1 st ITF symbol length lock, scan the above bar code and the appropriate code bytes located in Section M. ³ 9 0 1 7 0 0 To specify a 2 nd ITF symbol length lock, scan the above bar code and the appropriate code bytes located in Section M. ~ ITF Minimum Symbol Length Refer to the Multi-Code Configuration Method on page x. ³ 9 0 3 4 0 0 To specify a minimum number of ITF characters to be decoded, scan the above bar code and the appropriate code bytes located in Section M.

SECTION A STANDARD 2 OF 5 Enable Standard 2 of 5 * Disable Standard 2 of 5 ³ 1 0 0 1 1 0 ³ 1 0 0 1 0 0 ~ Standard 2 of 5 Symbol Length Lock ³ 9 0 1 5 0 0 To specify a minimum number of ITF characters to be decoded, scan the above bar code and the appropriate code bytes located in Section M. Refer to the Multi-Code configuration method on page x. Code Types & Decode Rules A 9

Code Types & Decode Rules A 10 SECTION A OTHER 2 OF 5 CODES Enable Matrix 2 of 5 * Disable Matrix 2 of 5 ³ 1 0 0 0 1 5 ³ 1 0 0 0 0 5 Enable 15 Digit Airline 2 of 5 * Disable 15 Digit Airline 2 of 5 ³ 1 0 0 0 1 4 ³ 1 0 0 0 0 4

SECTION A Enable 13 Digit Airline 2 of 5 OTHER 2 OF 5 CODES * Disable 13 Digit Airline 2 of 5 ³ 1 0 0 3 1 3 ³ 1 0 0 3 0 3 Enable Hong Kong 2 of 5 * Disable Hong Kong 2 of 5 ³ 1 0 0 3 1 6 ³ 1 0 0 3 0 6 Code Types & Decode Rules A 11

Code Types & Decode Rules A 12 SECTION A CODABAR * Enable Codabar * Disable Codabar ³ 1 0 0 1 1 4 ³ 1 0 0 1 0 4 Enable Dual Field Codabar * Disable Dual Field Codabar ³ 1 0 0 0 1 2 ³ 1 0 0 0 0 2 Enable Tab in Dual Codabar * Disable Tab in Dual Codabar ³ 1 0 8 0 1 2 ³ 1 0 8 0 0 2 This feature requires Dual Field Codabar to be enabled. The scanner will insert a tab between the fields of the dual field Codabar.

SECTION A CODE 93 AND CODE 11 * Enable Code 93 Disable Code 93 ³ 1 0 0 1 1 2 ³ 1 0 0 1 0 2 Enable Code 11 * Disable Code 11 ³ 1 0 0 0 1 3 ³ 1 0 0 0 0 3 Code Types & Decode Rules A 13

Code Types & Decode Rules A 14 SECTION A Enable Telepen * Disable Telepen TELEPEN ³ 1 0 0 0 1 7 ³ 1 0 0 0 0 7 Enable ALPHA Telepen * Disable ALPHA Telepen ³ 1 0 0 0 1 6 ³ 1 0 0 0 0 6

SECTION A Enable MSI Plessey PLESSEY CODES * Disable MSI Plessey ³ 1 0 0 2 1 2 ³ 1 0 0 2 0 2 * No MSI Plessey Check Digit ³ 2 0 0 7 0 4 The scanner will not test MSI Plessey bar codes for a check digit. Enable MSI Plessey MOD 10/10 Check Digit * Enable MSI Plessey MOD 10 Check Digit ³ 2 0 0 7 3 4 The scanner will test MSI Plessey bar codes for a double Modulo 10 check digit. ³ 2 0 0 7 2 4 The scanner will test MSI Plessey bar codes for a single Modulo 10 check digit. Code Types & Decode Rules A 15

Code Types & Decode Rules A 16 SECTION A Transmit MSI Plessey Check Digit PLESSEY CODES * Do Not Transmit MSI Plessey Check Digit ³ 1 0 7 7 1 1 This option works in conjunction with one or both of the Enabled MSI Plessey Mode options. ³ 1 0 7 7 0 1 The scanner will not transmit MSI Plessey check digit characters. Enable UK Plessey * Disable UK Plessey ³ 1 0 0 1 1 7 ³ 1 0 0 1 0 7 Enable UK Plessey A to X Conversion * Disable UK Plessey A to X Conversion ³ 1 0 0 7 1 6 ³ 1 0 0 7 0 6

SECTION A OTHER DECODE FEATURES Enable Double Border Required/Large Inter-Character Space * Disable Double Border Required/Large Inter-Character Space ³ 1 0 0 0 1 1 ³ 1 0 0 0 0 1 ~ Minimum Symbol Length ~ Symbol Length Lock ³ 9 0 1 8 0 0 Omnidirectional default is 4. Combine this code with the proper Code Bytes, to specify the minimum number of characters in all non-upc/ean bar codes. ³ 9 0 1 9 0 0 This code combined with the proper Code Bytes, locks the bar code s length into place. Refer to the Multi-Code Configuration Method on page x. Code Types & Decode Rules A 17

Code Types & Decode Rules A 18 SECTION A CONFIGURABLE CODE LENGTHS There are seven bar code lock lengths available. Specific code types can be assigned to a lock length using the Multi-Code configuration method. Example: 1. Scan the enter/exit configuration bar code. 2. Scan the code length lock #1 bar code. 3. Scan the three Code Bytes that represent the code length. 4. Scan the matching code type lock #1 bar code. 5. Scan the three code bytes that represent the code type. Refer to the Code Type Table in Section M. 6. Repeat steps 2 through 5 for lock lengths 2 through 7 if desired. 7. Scan the enter/exit configuration bar code when finished to save settings. ~ Code Length Lock #1 ~ Code Type Lock #1 ³ 9 0 2 0 0 0 ³ 9 0 2 1 0 0 ~ Code Length Lock #2 ~ Code Type Lock #2 ³ 9 0 2 2 0 0 ³ 9 0 2 3 0 0

SECTION A ~ Code Length Lock #3 CONFIGURABLE CODE LENGTHS ~ Code Type Lock #3 ³ 9 0 2 4 0 0 ³ 9 0 2 5 0 0 ~ Code Length Lock #4 ~ Code Type Lock #4 ³ 9 0 2 6 0 0 ³ 9 0 2 7 0 0 ~ Code Length Lock #5 ~ Code Type Lock #5 ³ 9 0 2 8 0 0 ³ 9 0 2 9 0 0 Code Types & Decode Rules A 19

Code Types & Decode Rules A 20 SECTION A ~ Code Length Lock #6 CONFIGURABLE CODE LENGTHS ~ Code Type Lock #6 ³ 9 0 3 0 0 0 ³ 9 0 3 1 0 0 ~ Code Length Lock #7 ~ Code Type Lock #7 ³ 9 0 3 2 0 0 ³ 9 0 3 3 0 0

SECTION A RSS 14 FEATURES Enable RSS 14 * Disable RSS 14 ³ 1 0 0 4 1 3 ³ 1 0 0 4 0 3 * Transmit RSS 14 Check Digit Do Not Transmit RSS 14 Check Digit ³ 1 1 4 9 0 0 ³ 1 1 4 9 1 0 Code Types & Decode Rules A 21

Code Types & Decode Rules A 22 SECTION A * Transmit RSS 14 Application ID RSS 14 FEATURES Do Not Transmit RSS 14 Application ID ³ 1 1 4 9 0 1 ³ 1 1 4 9 1 1 Application identifier 01 is transmitted by default. * Transmit RSS 14 Symbology ID Do Not Transmit RSS 14 Symbology ID ³ 1 1 4 9 0 2 ³ 1 1 4 9 1 2 Symbology identifier ]e0 is transmitted by default.

SECTION A RSS LIMITED FEATURES Enable RSS Limited * Disable RSS Limited ³ 1 0 0 4 1 4 ³ 1 0 0 4 0 4 * Transmit RSS Limited Check Digit Do Not Transmit RSS Limited Check Digit ³ 1 1 4 9 0 3 ³ 1 1 4 9 1 3 Code Types & Decode Rules A 23

Code Types & Decode Rules A 24 SECTION A * Transmit RSS Limited Application ID RSS LIMITED FEATURES Do Not Transmit RSS Limited Application ID ³ 1 1 4 9 0 4 ³ 1 1 4 9 1 4 Application identifier 01 is transmitted by default. * Transmit RSS Limited Symbology ID Do Not Transmit RSS Limited Symbology ID ³ 1 1 4 9 0 5 ³ 1 1 4 9 1 5 Symbology identifier ]e0 is transmitted by default.

SECTION A RSS EXPANDED FEATURES Enable RSS Expanded * Disable RSS Expanded ³ 1 0 0 4 1 5 ³ 1 0 0 4 0 5 * Transmit RSS Expanded Symbology ID Do Not Transmit RSS Expanded Symbology ID ³ 1 1 4 9 0 6 ³ 1 1 4 9 1 6 Symbology identifier ]e0 is transmitted by default. Code Types & Decode Rules A 25

SECTION B Enable Two Digit Supplements SUPPLEMENTS/REDUNDANCY * Disable Two Digit Supplements ³ 1 0 1 2 1 7 ³ 1 0 1 2 0 7 * Enable Two Digit Redundancy Disable Two Digit Redundancy ³ 1 0 1 2 1 2 Twice before accepting data, the scanner will scan the bar code plus the two digit add on. ³ 1 0 1 2 0 2 When scanned, will not implement the two digit redundancy feature. Enable Five Digit Supplements * Disable Five Digit Supplements ³ 1 0 1 2 1 6 ³ 1 0 1 2 0 6 Supplements B 1

Supplements B 2 SECTION B Enable Five Digit Redundancy SUPPLEMENTS/REDUNDANCY * Disable Five Digit Redundancy ³ 1 0 1 2 1 1 Twice before accepting data, the scanner will scan the bar code plus the five digit add on. ³ 1 0 1 2 0 1 The scanner will not implement the five digit redundancy feature. Supplements are Required * Supplements are not Required ³ 1 0 1 2 1 3 All UPC/EAN labels that are scanned must have a supplement. ³ 1 0 1 2 0 3 UPC/EAN labels do not require a supplement to be scanned. Enable Remote Supplemental Requirement * Disable Remote Supplemental Requirement ³ 1 0 1 4 1 6 ³ 1 0 1 4 0 6

SECTION B Enable Bookland (978) Supplement Requirement SUPPLEMENTS * Disable Bookland (978) Supplement Requirement ³ 1 0 1 4 1 7 ³ 1 0 1 4 0 7 Enable 977 (2 digit) Supplemental Requirement * Disable 977 (2 digit) Supplemental Requirement ³ 1 0 1 3 1 4 The scanner will require a 2 digit supplement be scanned when an EAN-13 code begins with 977. ³ 1 0 1 3 0 4 The scanner will not require a 2 digit supplement be scanned whenever an EAN-13 code begins with 977. Enable 378/379 French Supplement Requirement * Disable 378/379 French Supplemental Requirement ³ 1 0 1 3 1 3 ³ 1 0 1 3 0 3 Supplements B 3

Supplements B 4 SECTION B SUPPLEMENTS Enable 434/439 German Supplemental Requirement * Disable 434/439 German Supplemental Requirement ³ 1 0 1 4 1 5 ³ 1 0 1 4 0 5 Enable 414/419 German Supplemental Requirement * Disable 414/419 German Supplemental Requirement ³ 1 0 1 4 1 3 ³ 1 0 1 4 0 3 Enable # System 2 Requires Supplements * Disable # System 2 Requires Supplements ³ 1 0 1 4 1 2 ³ 1 0 1 4 0 2

SECTION B SUPPLEMENTS Enable # System 5 Requires Supplements * Disable # System 5 Requires Supplements ³ 1 0 1 2 1 5 ³ 1 0 1 2 0 5 Enable 8711685 Requires 5-Digit Supplement * Disable 8711685 Requires 5-Digit Supplement ³ 1 0 7 6 1 3 The scanner will require a 5-digit supplement to be scanned when an EAN-13 code begins with 8711685. ³ 1 0 7 6 0 3 The scanner will not require a 5-digit supplement to be scanned when an EAN-13 code begins with 8711685. This feature is not available with all models. Enable Coupon Code 128 * Disable Coupon Code 128 ³ 1 0 0 3 1 5 ³ 1 0 0 3 0 5 Supplements B 5

Supplements B 6 SECTION B Enable Code 128 ]C1 Extended Code Format SUPPLEMENTS * Disable Code 128 ]C1 Extended Code Format ³ 1 0 1 4 1 1 The scanner will transmit a ]C1 at the beginning of the code 128 portion of the coupon code. ³ 1 0 1 4 0 1 The scanner will not transmit a ]C1 at the beginning of the code 128 portion of the coupon code. Enable 128 Group Separators * Disable 128 Group Separators ³ 1 0 1 4 1 4 GS (1DH) character will be transmitted with coupon Code 128 codes. ³ 1 0 1 4 0 4 GS (1DH) character will not be transmitted with coupon Code 128 codes. * 100 msec to Find Supplemental 200 msec to Find Supplemental ³ 3 0 1 3 1 0 The scanner will allot 100 milliseconds to find an add on after a main UPC/EAN bar code has been scanned. ³ 3 0 1 3 2 0 The scanner will allot 200 milliseconds to find an add on after a main UPC/EAN bar code has been scanned.

SECTION B SUPPLEMENTS 400 msec to Find Supplemental ³ 3 0 1 3 4 0 The scanner will allot 400 milliseconds to find an add on after a main UPC/EAN bar code has been scanned. Enable Code ID s with Supplements * Disable Code ID s with Supplements ³ 1 0 1 2 1 4 ³ 1 0 1 2 0 4 Allow 2/5 on 977 Bar Code Allow 2 on 977 Bar Code ³ 1 2 4 8 1 1 This feature allows either 2 or 5 digit supplements if 977 mode is active. ³ 1 2 4 8 0 1 This feature allows 2 digit supplements if 977 mode is active. Supplements B 7

Supplements B 8 SECTION B * Beep Once on Supplements SUPPLEMENTS Beep twice on Supplements ³ 1 1 8 4 0 6 ³ 1 1 8 4 1 6 Enable ISBN Check Digit Transmission Disable ISBN Check Digit Transmission ³ 1 0 1 3 1 5 ³ 1 0 1 3 0 5 This feature is not available with all models.

SECTION B SUPPLEMENTS Enable Bookland to ISBN Conversion * Disable Bookland to ISBN Conversion ³ 1 0 1 3 1 7 ³ 1 0 1 3 0 7 This feature is not available with all models. Enable ISBN Re-Formatting * Disable ISBN Re-Formatting ³ 1 0 1 3 1 6 ³ 1 0 1 3 0 6 This feature is not available with all models. Supplements B 9

Supplements B 10 SECTION B Enable ISSN Check Digit Transmission SUPPLEMENTS * Disable ISSN Check Digit Transmission ³ 1 1 5 1 1 5 ³ 1 1 5 1 0 5 Enable ISSN Re-Formatting * Disable ISSN Re-Formatting ³ 1 1 5 1 1 6 ³ 1 1 5 1 0 6 Transmit a hyphen with the barcode. Enable 977 to ISSN Conversion * Disable 977 to ISSN Conversion ³ 1 1 5 1 1 7 Convert 977 periodicals to ISSN format. ³ 1 1 5 1 0 7 Do not convert 977 periodicals to ISSN format.

SECTION B Enable Number System 4 Coupon Code 128 SUPPLEMENTS * Disable Number System 4 Coupon Code 9128 ³ 1 0 1 0 1 2 ³ 1 0 1 0 0 2 Supports Coupon Code 128 for Number System 4 bar codes. Enable UPC Discard * Disable UPC Discard ³ 1 0 1 0 1 3 ³ 1 0 1 0 0 3 Supports UPC discard if the Code 128 portion of the Coupon Code 128 is scanned. Allow Supplements and UPC in Same Line Disable Supplements and UPC in Same Line ³ 1 0 1 0 1 4 ³ 1 0 1 0 0 4 This feature requires 2 digit supplements be enabled as well as required redundancy and supplements. Supplements B 11

SECTION C * Enable RS-232 COMMUNICATIONS Load Keyboard Wedge Defaults ³ 4 1 5 5 5 4 The scanner will work with RS-232 ±12V serial output. ³ 9 9 9 9 9 4 Scan this before selecting Normal or Stand Alone Mode. Enable Light Pen/Wand Communication Enable Keyboard Wedge Emulation ³ 4 1 5 5 2 4 Use this option if a scanner is used in place of a light pen. ³ 5 1 5 5 1 4 3 Select if the scanner provides keyboard emulation by converting the scanned bar code data to the PC keyboard scan code equivalent. Enable Stand-Alone Keyboard Scanner ³ 5 1 5 5 1 5 3 Allows the scanner to be used without an external keyboard. Communications C 1

Communications C 2 SECTION C Load OCIA Defaults COMMUNICATIONS Enable OCIA Output ³ 9 9 9 9 9 3 Scan this before selecting Enable OCIA output. ³ 4 1 5 5 4 4 Select this option if the communications requirement is an Optically Coupled Interface Adapter (OCIA). This is a docked (by the host) serial interface. Load IBM 46xx Defaults Enable IBM 46xx Communication ³ 9 9 9 9 9 5 Scan this before selecting Enable IBM 46xx Communication ³ 4 1 5 5 0 4 Select this option for IBM 46xx SIOC/RS485 communications. Not all scanners support this interface. The correct interface board is required.

SECTION C COMMUNICATIONS Load Low Speed External USB Defaults Enable Low Speed USB Refer to Section P for full speed USB options. ³ 9 9 9 9 7 8 ³ 4 1 5 5 1 1 4 Load Low Speed Internal USB Defaults Enable No Communication Mode ³ 9 9 9 9 4 1 ³ 4 1 5 5 3 4 Select this option if the scanner does not interface with the host device. Reserved Reserved ³ 4 1 5 5 6 4 ³ 9 1 7 5 0 0 Communications C 3

SECTION D CONFIGURATION MODE OPTIONS Allow Configuration Mode on Power-Up * Allow Configuration Mode Anytime ³ 1 1 8 1 1 7 The scanner can only enter MetroSet mode before any bar codes are scanned. ³ 1 1 8 1 0 7 Allow MetroSet configuration at any time. Allow Configuration Codes on Power Up * Allow Configuration Codes Anytime ³ 1 1 8 1 1 6 Once a product bar code is scanned after power-up, the scanner will not accept configuration bar codes. ³ 1 1 8 1 0 6 Allows scanning of configuration bar codes any time. Enable Single Code Configuration Disable Single Code Configuration ³ 1 1 8 2 1 2 ³ 1 1 8 2 0 2 Scanner Operation D 1

Scanner Operation D 2 SECTION D SCAN BUFFERS * 1 Scan Buffer 2 Scan Buffers ³ 3 1 8 0 0 0 The scanner will scan one bar code in the scan field and not scan again until the bar code is removed from the scan field for the duration of the same symbol time out. ³ 3 1 8 0 1 0 The scanner will scan 2 bar codes in the scan field one time each. These 2 bar codes will not be scanned again until they are removed from the scan field for the duration of the same symbol time out. 3 Scan Buffers 4 Scan Buffers ³ 3 1 8 0 2 0 Same function as 2 Scan Buffers, but 3 bar codes are in the scan field. ³ 3 1 8 0 3 0 Same function as 2 Scan Buffers, but 4 bar codes are in the scan field.

SECTION D SCAN BUFFERS 5 Scan Buffers 6 Scan Buffers ³ 3 1 8 0 4 0 Same function as 2 Scan Buffers, but 5 bar codes are in the scan field. ³ 3 1 8 0 5 0 Same function as 2 Scan Buffers, but 6 bar codes are in the scan field. 7 Scan Buffers 8 Scan Buffers ³ 3 1 8 0 6 0 Same function as 2 Scan Buffers, but 7 bar codes are in the scan field. ³ 3 1 8 0 7 0 Same function as 2 Scan Buffers, but 8 bar codes are in the scan field. Scanner Operation D 3

Scanner Operation D 4 SECTION D REDUNDANT SCANS * 0 Redundant Scans 1 Redundant Scans ³ 3 0 1 1 0 0 Requires 1 good decode for a good scan. ³ 3 0 1 1 1 0 Requires 2 consecutive decodes of the same bar code data for a good scan. 2 Redundant Scans 3 Redundant Scans ³ 3 0 1 1 2 0 Requires 3 consecutive decodes of the same bar code data for a good scan. ³ 3 0 1 1 3 0 Requires 4 consecutive decodes of the same bar code data for a good scan.

SECTION D REDUNDANT SCANS 4 Redundant Scans 5 Redundant Scans ³ 3 0 1 1 4 0 Requires 5 consecutive decodes of the same bar code data for a good scan. ³ 3 0 1 1 5 0 Requires 6 consecutive decodes of the same bar code data for a good scan. 6 Redundant Scans 7 Redundant Scans ³ 3 0 1 1 6 0 Requires 7 consecutive decodes of the same bar code data for a good scan. ³ 3 0 1 1 7 0 Requires 8 consecutive decodes of the same bar code data for a good scan. Scanner Operation D 5

Scanner Operation D 6 SECTION D MISCELLANEOUS DECODE FEATURES * Enable Segmented UPC Decoding Disable Segmented UPC Decoding ³ 1 0 1 1 1 3 Enabling segmented UPC decoding aids in deciphering damaged or incomplete bar codes. ³ 1 0 1 1 0 3 Disable this feature when bar codes are in good reading condition. This will speed up decoding and improve over all accuracy. Optional Same Symbol Check * Normal Same Symbol Check ³ 1 1 8 1 1 3 Requires 1 different character between successive bar codes to consider the bar code new. ³ 1 1 8 1 0 3 Requires 3 different characters between successive bar codes to consider the bar code new.

SECTION D DEPTH OF FIELD ADJUSTMENTS Do not change these settings unless instructed by a Metrologic representative. * Optimize for Low Density Codes Optimize for High Density Codes ³ 4 1 8 7 9 0 ³ 4 1 8 7 1 3 0 Fixed for High Density Codes Fixed for Medium Density Codes ³ 4 1 8 7 0 0 ³ 4 1 8 7 1 0 Fixed for Low Density Codes ³ 4 1 8 7 2 0 For use with omnidirectional scanners only. Scanner Operation D 7

Scanner Operation D 8 SECTION D SAME SYMBOL TIME OUTS These numbers determine the length of time before a bar code can be rescanned after it is removed from the scan field. Single code fixed settings in msecs of No, 50, 100, 200, 500, 1200 (1.2 sec), 2000 (2.0 sec) and infinite are available. User configurable values can be set in user-configurable increments of 50 msecs to 6350 msecs (6.35 sec). No Same Symbol Time Out Same Symbol Time Out 100 msecs ³ 8 1 8 9 0 0 ³ 8 1 8 9 2 0 Same Symbol Time Out 200 msecs * Same Symbol Time Out 500 msecs ³ 8 1 8 9 4 0 ³ 8 1 8 9 1 0 0 Same Symbol Time Out 1200 msecs Same Symbol Time Out 2000 msecs ³ 8 1 8 9 2 4 0 ³ 8 1 8 9 4 0 0

SECTION D SAME SYMBOL TIME OUTS Infinite Same Symbol Time Out ~ Variable Same Symbol Time Out ³ 1 1 8 9 1 7 The scanner will not repetitively scan the same bar code. This option overrides the symbol rescan time-outs. ³ 9 1 8 9 0 0 Using the Multi-Code Method (page x), scan this bar code and a code byte sequence from Section M to set the same symbol time-out duration. Values range from 001 to 127 (50 to 6350 msecs). * Enable Bar Code Absence Detection Excludes the MS2000 Stratos Series. BARCODE ABSENCE Disable Bar Code Absence Detection ³ 1 1 8 2 0 0 ³ 1 1 8 2 1 0 Enable Stratos Bar Code Absence Detection * Disable Stratos Bar Code Absence Detection ³ 1 2 4 9 1 7 The scan field must be free of data for 50 milliseconds to accept a new bar code. ³ 1 2 4 9 0 7 Scanner Operation D 9

Scanner Operation D 10 SECTION D Flash Green LED if Rescan Allowed LED OPTIONS * Do not flash Green LED if Rescan Allowed ³ 1 1 8 3 1 3 ³ 1 1 8 3 0 3 This indicates same symbol timeout has elapsed. Reverse LED Functions * Normal LED Functions ³ 1 1 8 3 1 2 Red = Laser On Green = Good Read ³ 1 1 8 3 0 2 Green = Laser On Red = Good Read * Laser LED High Intensity Laser LED Low Intensity ³ 2 4 3 1 0 0 Laser LED Intensity is High or Normal. ³ 2 4 3 1 2 0 Laser LED is Low Intensity This feature is not available with all models.

SECTION D Laser LED Off LED OPTIONS * Scan LED High Intensity ³ 2 4 3 1 3 0 The laser LED does not signify laser ON. The LED will continue to light for all other functions. This feature is not available with all models. ³ 2 4 3 1 0 2 Scan LED Intensity is High or Normal. Scan LED Low Intensity ³ 2 4 3 1 2 2 Scan LED Off Scan LED Intensity is Low Intensity This feature is not available with all models. ³ 2 4 3 1 3 2 The scan LED does not signify barcode scanning. The LED will continue to light for all other functions. This feature is not available with all models. Scanner Operation D 11

Scanner Operation D 12 SECTION D BEEPER OPTIONS * Normal Tone Optional Tone 1 ³ 3 1 8 5 7 5 ³ 3 1 8 5 6 5 Optional Tone 2 Optional Tone 3 ³ 3 1 8 5 5 5 ³ 3 1 8 5 4 5 Optional Tone 4 Optional Tone 5 ³ 3 1 8 5 3 5 ³ 3 1 8 5 2 5

SECTION D Optional Tone 6 BEEPER OPTIONS No Beep ³ 3 1 8 5 1 5 ³ 3 1 8 5 0 5 * Enable Good Scan Beep Disable Good Scan Beep ³ 1 4 1 9 0 3 Enable good scan beep on power up. ³ 1 4 1 9 1 3 Disable good scan beep on power up. * Enable Button Beep Controls Disable Button Beep Controls ³ 1 1 9 7 0 1 This feature is not available with all models. ³ 1 1 9 7 1 1 This feature is not available with all models. Scanner Operation D 13

Scanner Operation D 14 SECTION D Next Beep Tone BEEPER OPTIONS Next Volume ³ 9 9 9 9 7 5 ³ 9 9 9 9 7 4 * Loudest Volume 2 nd Loudest Volume ³ 2 1 8 5 0 0 ³ 2 1 8 5 1 0 3 rd Loudest Volume No Volume ³ 2 1 8 5 2 0 ³ 2 1 8 5 3 0

SECTION D * Beep Once on Supplements BEEPER OPTIONS Beep Twice on Supplements ³ 1 1 8 4 0 6 ³ 1 1 8 4 1 6 Enable Fast Beep * Disable Fast Beep ³ 1 1 8 4 1 4 ³ 1 1 8 4 0 4 Scanner Operation D 15

Scanner Operation D 16 SECTION D Beep on BEL Command BEEPER OPTIONS * Ignore BEL Command ³ 1 1 8 4 1 7 ³ 1 1 8 4 0 7 The scanner beeps when it receives a BEL character from the host. If a number is sent within 200 msecs before the BEL character, then the scanner will beep that number of times. Enable Light Pen Toggle During Beep * Disable Light Pen Toggle During Beep ³ 1 1 6 9 1 3 ³ 1 1 6 9 0 3 The scanner will beep and toggle the light pen data line on a successful decode. This drives a good read indicator.

SECTION D INTER-CHARACTER DATA TRANSMISSION DELAYS Use these codes to select the amount of delay between sending data characters and Bar Code records from the scanner to the host. This helps prevent the scanner from overflowing host input buffers. * 1 msec Inter-Character Delay 10 msec Inter-Character Delay ³ 8 1 8 8 1 0 ³ 8 1 8 8 1 0 0 25 msec Inter-Character Delay ~ Variable msec Inter-Character Delay ³ 8 1 8 8 2 5 0 ³ 9 1 8 8 0 0 Scan this bar code and a sequence of code bytes in Section M to set the delay between characters sent to the host system. Delay range can be set from 1 to 255 msecs. Refer to the Multi-Code Configuration Method on page x. Scanner Operation D 17

Scanner Operation D 18 SECTION D INTER-CHARACTER DATA TRANSMISSION DELAYS No Inter-Character Delay ³ 8 1 8 8 0 0 INTER-RECORD DATA TRANSMISSION DELAYS ~ Variable Inter-Record Delay ³ 9 1 9 3 0 0 Turn Off Laser During Inter-Record Delay * Leave Laser On During Inter-Record Delay ³ 1 1 9 3 1 7 ³ 1 1 9 3 0 7

SECTION D Enable Communications Time Outs COMMUNICATION TIME OUT OPTIONS * Disable Communications Time Outs ³ 1 1 8 4 1 2 ³ 1 1 8 4 0 2 * Beep Before Transmit Beep After Transmit ³ 1 1 8 4 1 3 Scanner will beep before each label is transmitted. ³ 1 1 8 4 0 3 Scanner will beep after each label is transmitted. ~ Variable Communications Time Out * Default Communications Time Out (2 secs) ³ 9 1 9 1 0 0 ³ 8 1 9 1 4 0 0 Scanner Operation D 19

Scanner Operation D 20 SECTION D COMMUNICATION TIME OUT OPTIONS Short Communications Time Out (1 sec) Long Communications Time Out (4 secs) ³ 8 1 9 1 2 0 0 ³ 8 1 9 1 8 0 0 Three Beeps on Time Out * No Beeps on Time Out ³ 1 1 8 4 1 0 ³ 1 1 8 4 0 0 Razzberry Tone on Time Out * No Razzberry Tone on Time Out ³ 1 1 8 4 1 1 ³ 1 1 8 4 0 1

SECTION D HOST SCANNER COMMANDS Enable D/E Disable Command * Disable D/E Disable ³ 1 1 8 0 1 5 The scanner will disable scanning after it receives and ASCII D from the host device. It will enable scanning when it receives an ASCII E. ³ 1 1 8 0 0 5 Do not monitor D/E commands. Enable Z/R Type D/E Simulation * No Z/R Type D/E Simulation ³ 1 1 8 2 1 1 The scanner will disable scanning after it receives an ASCII Z from the host device. It will enable scanning when it receives an ASCII R. ³ 1 1 8 2 0 1 Do not monitor Z/R commands. Scanner Operation D 21

Scanner Operation D 22 SECTION D Enable F/L Laser Command HOST SCANNER COMMANDS * Disable F/L Laser Command ³ 1 1 8 0 1 4 The scanner will turn off the laser after receiving an ASCII F character. The laser will turn on after it receives an ASCII L character. ³ 1 1 8 0 0 4 Do not monitor F/L commands. Motor On/Off Using M/O Commands For use with omnidirectional scanners only. * Disable M/O Commands ³ 1 1 8 2 1 3 The scanner will turn the motor OFF after it receives an ASCII O character. The motor will turn ON after the scanner receives an ASCII M character. ³ 1 1 8 2 0 3 Do not monitor the M/O commands.

SECTION D Enable I Command HOST SCANNER COMMANDS Disable I Command ³ 1 1 5 9 1 7 ³ 1 1 5 9 0 7 Enable i Command Disable i Command ³ 1 1 5 9 1 6 ³ 1 1 5 9 0 6 Enable SI/SO Command Disable SI/SO Command ³ 1 2 5 0 1 4 ³ 1 2 5 0 0 4 Scanner Operation D 23

Scanner Operation D 24 SECTION D HOST SCANNER COMMANDS Use DTR Scan Disable * Do not use DTR Scan Disable ³ 1 1 8 1 1 5 The scanner will monitor the DTR input to determine if scanning should be allowed. A +12V active level enables decoding. A -12V inactive level disables decoding. ³ 1 1 8 1 0 5 Do not monitor the DTR input. Enable Pass Through Disable Pass Through ³ 1 2 4 7 1 1 ³ 1 2 4 7 0 1 The AUX scanner must be configured for the same Baud rate as the host, with STX prefix, Nixdorf ID characters and CR Terminator enabled. Activate on DC2 Character * Do Not Activate on DC2 Character ³ 1 1 8 1 1 0 ³ 1 1 8 1 0 0

SECTION D HOST SCANNER COMMANDS Transmit NO READ if DC2 Activated Do Not Transmit NO READ if DC2 Activated ³ 1 1 8 1 1 1 ³ 1 1 8 1 0 1 No Green LED During NO READ Xmit * Green LED During NO READ Xmit ³ 1 1 8 3 1 1 ³ 1 1 8 3 0 1 Scanner Operation D 25

Scanner Operation D 26 SECTION D POWER SAVE MODES Always Power Save Mode No Power Save Mode For use with omnidirectional scanners only. ³ 1 1 8 6 1 7 The scanner enters power save mode immediately after power-up and after each bar code scanned. ³ 8 1 8 6 0 0 The scanner will never enter power save mode. Power Save Mode in 1 minute Power Save Mode in 2 minutes ³ 8 1 8 6 1 0 The scanner enters power save mode when the scanner remains idle for 1 min. ³ 8 1 8 6 2 0 The scanner enters power save mode if the scanner remains idle for 2 min. Power Save in 5 Minutes Power Save in 10 Minutes ³ 8 1 8 6 5 0 The scanner enters power save mode if the scanner remains idle for 5 min. ³ 8 1 8 6 1 0 0 The scanner enters power save mode if the scanner remains idle for 10 min.

SECTION D POWER SAVE MODES Power Save in 20 Minutes Power Save in 30 Minutes For use with omnidirectional scanners only. ³ 8 1 8 6 2 0 0 The scanner enters power save mode if the scanner remains idle for 20 min. ³ 8 1 8 6 3 0 0 The scanner enters power save mode if the scanner remains idle for 30 min. Default Power Save Mode ³ 3 1 9 4 0 0 This feature is not available with all models. Some Metrologic scanners automatically wake or exit from the power save mode if the IR detects movement. Other Metrologic scanners wake if their multi-function Button is pressed. Please refer to the Installation and User s Guide specific to each product. Blink Power Save Mode ³ 3 1 9 4 1 0 The laser Blinks OFF & ON after a configured period of non-use. When the scanner recognizes a bar code it will exit the blink mode. This feature is not available with all models. Scanner Operation D 27

Scanner Operation D 28 SECTION D Laser OFF Power Save Mode POWER SAVE MODES Laser Motor OFF Power Save Mode ³ 3 1 9 4 2 0 The laser turns OFF after a configured period of non-use. ³ 3 1 9 4 3 0 The laser and motor turns OFF after a configured period of non-use. This feature is not available with all models. Dual #1 Power Save Mode Some Metrologic scanners automatically wake or exit from the power save mode if the IR detects movement. Other Metrologic scanners wake if their multi-function Button is pressed. Please refer to the Installation and User s Guide specific to each product. This feature is not available with all models. Dual #2 Power Save Mode ³ 3 1 9 4 4 0 The laser blinks OFF & ON after a configured period of non-use then the laser and motor turn OFF at thirtyminute intervals. Example 1: Example of Dual #1 Power Save Mode with the power save timeout set to 15 minutes. ³ 3 1 9 4 6 0 The laser turns OFF after a configured period of nonuse then the motor turns OFF at thirty-minute intervals. Example 2: Example of Dual #2 Power Save Mode with the power save timeout set to 15-minutes. This feature is not available with all models. This feature is not available with all models.

SECTION D * Enable Power Save Switch POWER SAVE MODES Disable Power Save Switch ³ 1 1 9 7 0 0 This feature is not available with all models. ³ 1 1 9 7 1 0 This feature is not available with all models. Scanner Operation D 29

Scanner Operation D 30 SECTION D JAPANESE DOUBLE FIELD SUPPORT To support Japanese Double Field Bar Codes, first make sure you have your scanner programmed to the following settings. Disable Segmented UPC Decoding Enable 2 scan buffers Disable bar code absence detection Enable normal code selects Then, scan the Enable Japan 2 Field bar code. Enable Japan 2 Field * Disable Japan 2 Field ³ 1 2 4 7 1 3 ³ 1 2 4 7 0 3 Next, select the matching bar codes that are used for double field symbols. Note that only UPC/EAN bar codes are allowed in double field mode. Select at least two characters for each bar code. The maximum is 4 upper and 4 lower bar codes. EXAMPLE To select 54 as the first two characters in the Upper Code pair 1: 1. Scan the Upper Code 1 Character 1 bar code (shown on page D-31) 2. Determine the correct Code Byte Value for the character 5 in 54 (Refer to Section M s ASCII Reference Table on pages M-6 to M-10) a. Scan Code Byte 0 b. Scan Code Byte 5 c. Scan Code Byte 3 3. Scan the Upper Code 1 Character 2 bar code (shown on page D-31) 4. Determine the correct Code Byte Value for the character 4 in 54. a. Scan Code Byte 0 b. Scan Code Byte 5 c. Scan Code Byte 2 To select 18 as the first two characters in the Lower Code pair 1: 1. Scan the Lower Code 1 Character 1 bar code (shown on page D-31) 2. Determine the correct Code Byte Value for the character 1 in 18 (refer to Section M s ASCII Reference Table) a. Scan Code Byte 0 b. Scan Code Byte 4 c. Scan Code Byte 9 3. Scan the Lower Code 1 Character 2 bar code (shown on page D-31) 4. Determine the correct Code Byte Value for the character 8 in 18. (Refer to Section M s ASCII Reference Table on pages M-6 to M-10) a. Scan Code Byte 0 b. Scan Code Byte 5 c. Scan Code Byte 6

SECTION D JAPANESE DOUBLE FIELD SUPPORT Upper Code 1 Character 1 Upper Code 1 Character 2 ³ 9 3 0 0 0 0 ³ 9 3 0 1 0 0 Lower Code 1 Character 1 Lower Code 1 Character 2 ³ 9 3 0 2 0 0 ³ 9 3 0 3 0 0 Upper Code 2 Character 1 Upper Code 2 Character 2 ³ 9 3 0 4 0 0 ³ 9 3 0 5 0 0 Scanner Operation D 31

Scanner Operation D 32 SECTION D JAPANESE DOUBLE FIELD SUPPORT Lower Code 2 Character 1 Lower Code 2 Character 2 ³ 9 3 0 6 0 0 ³ 9 3 0 7 0 0 Upper Code 3 Character 1 Upper Code 3 Character 2 ³ 9 3 0 8 0 0 ³ 9 3 0 9 0 0 Lower Code 3 Character 1 Lower Code 3 Character 1 ³ 9 3 1 0 0 0 ³ 9 3 1 1 0 0

SECTION D JAPANESE DOUBLE FIELD SUPPORT Upper Code 4 Character 1 Upper Code 4 Character 2 ³ 9 3 1 2 0 0 ³ 9 3 1 3 0 0 Lower Code 4 Character 1 Lower Code 4 Character 2 ³ 9 3 1 4 0 0 ³ 9 3 1 5 0 0 Scanner Operation D 33

Scanner Operation D 34 SECTION D Japanese Trial Time JAPANESE DOUBLE FIELD SUPPORT Enable Code Selects ³ 9 3 8 8 0 0 ³ 1 1 8 2 1 7 Scan the above bar code followed by the 3 code bytes in Section M that represent the timeout value desired if in special code select mode. 1 is equal to 100 milliseconds Example: If a 500 millisecond timeout is desired, scan the above code followed by code byte 0, code byte 0 and code byte 5. Enable Error Tone * Disable Error Tone ³ 1 1 8 5 1 3 ³ 1 1 8 5 0 3 Adds ability to sound RAZZ error tone when special code selects fail.

SECTION D Scanability ON TEST MODES * Scanability OFF ³ 1 1 8 0 1 7 ³ 1 1 8 0 0 7 The scanner will enter scanability test mode. Do not enable unless instructed to by a Metrologic representative. Scan Count Mode ON * Scan Count Mode OFF ³ 1 1 8 0 1 6 The scanner will enter scan count test mode and the scanner s firmware number will transmit to the host. Do not enable unless instructed to by a Metrologic representative. The Temporary Symbologies test code enables all major types of bar code symbologies, reduces the minimum number of characters required to 1, sets the minimum ITF characters required to 2, and adds the symbology name as a prefix to the transmission. This feature is disabled when power to the scanner is cycled OFF and ON. ³ 1 1 8 0 0 6 Temporary Symbologies ³ 9 9 8 0 4 1 Do not enable unless instructed to by a Metrologic representative Scanner Operation D 35

SECTION E CONFIGURABLE PREFIXES, ALL DATA Scan the Enter/Exit Configuration Mode bar code before trying to set this feature. Please refer to the Multi-Code method on page x. Enter/Exit Configuration Mode ~ Configurable Prefix Character #1 ³ 9 9 9 9 9 9 ³ 9 0 3 5 0 0 A prefix ID can be added and assigned for data transmission. Use this code with a 3-code byte sequence from Section M that represents the desired character. ~ Configurable Prefix Character #2 ~ Configurable Prefix Character #3 ³ 9 0 3 6 0 0 Assigns a 2 nd configurable prefix character. ³ 9 0 3 7 0 0 Assigns a 3 rd configurable prefix character. ~ Configurable Prefix Character #4 ~ Configurable Prefix Character #5 ³ 9 0 3 8 0 0 Assigns a 4 th configurable prefix character. ³ 9 0 3 9 0 0 Assigns a 5 th configurable prefix character. Prefixes/Suffixes E 1

Prefixes/Suffixes E 2 SECTION E ~ Configurable Prefix Character #6 CONFIGURABLE PREFIXES, ALL DATA ~ Configurable Prefix Character #7 ³ 9 0 4 0 0 0 Assigns a 6 th configurable prefix character. ³ 9 0 4 1 0 0 Assigns a 7 th configurable prefix character. ~ Configurable Prefix Character #8 ~ Configurable Prefix Character #9 ³ 9 0 4 2 0 0 Assigns a 8 th configurable prefix character. ³ 9 0 4 3 0 0 Assigns a 9 th configurable prefix character. ~ Configurable Prefix Character #10 * Clear all User Configurable Prefixes ³ 9 0 4 4 0 0 ³ 9 9 9 9 8 5

SECTION E CONFIGURABLE ID CHARACTERS, CODE SPECIFIC * Use Configurable Code ID Bytes as Prefixes Use Configurable Code ID Bytes as Suffixes ³ 1 0 5 5 0 7 User configured, code specific ID bytes are transmitted before the data. If using prefixes, user configured suffixes can not be used. ³ 1 0 5 5 1 7 User configured, code specific ID bytes are transmitted after the data. If using suffixes, user configured prefixes can not be used. IDENTIFIERS CHARACTER ~ Configurable UPC-A ID ~ Configurable UPC-E ID ³ 9 0 5 6 0 0 ³ 9 0 5 7 0 0 While using the Multi-Code method, scan this bar code followed by the 3 code byte bar codes in Section M that represent a unique ID character to be associated with this bar code type. (Refer to the Multi-Code Method on page x.) Prefixes/Suffixes E 3

Prefixes/Suffixes E 4 SECTION E CONFIGURABLE ID CHARACTERS, CODE SPECIFIC ~ Configurable EAN-8 ID ~ Configurable EAN-13 ID ³ 9 0 5 8 0 0 ³ 9 0 5 9 0 0 While using the Multi-Code method, scan this bar code followed by the 3 code byte bar codes in Section M that represent a unique ID character to be associated with this bar code type. (Refer to the Multi-Code Method on page x.) ~ Configurable Code 39 ID ~ Configurable Code 128 ID ³ 9 0 6 0 0 0 ³ 9 0 6 1 0 0

SECTION E CONFIGURABLE ID CHARACTERS, CODE SPECIFIC ~ Configurable Code 93 ID ~ Configurable Code 11 ID ³ 9 0 6 3 0 0 ³ 9 0 6 4 0 0 While using the Multi-Code method, scan this bar code followed by the 3 code byte bar codes in Section M that represent a unique ID character to be associated with this bar code type. (Refer to the Multi-Code method on page x.) ~ Configurable Telepen ID ~ Configurable TRI-OPTIC ID ³ 9 0 6 2 0 0 ³ 9 0 7 2 0 0 Prefixes/Suffixes E 5

Prefixes/Suffixes E 6 SECTION E CONFIGURABLE ID CHARACTERS, CODE SPECIFIC ~ Configurable Standard 2 of 5 ID ~ Configurable Interleaved 2 of 5 ID ³ 9 0 7 1 0 0 ³ 9 0 6 7 0 0 While using the Multi-Code method, scan this bar code followed by the 3 code byte bar codes in Section M that represent a unique ID character to be associated with this bar code type. (Refer to the Multi-Code method on page x.) ~ Configurable Matrix 2 of 5 ID ~ Configurable Airline 2 of 5 ID ³ 9 0 6 8 0 0 ³ 9 0 6 9 0 0

SECTION E ~ Configurable MSI Plessey ID CONFIGURABLE ID CHARACTERS CODE SPECIFIC ~ Configurable UK Plessey ID ³ 9 0 6 5 0 0 ³ 9 0 7 0 0 0 While using the Multi-Code method, scan this bar code followed by the 3 code byte bar codes in Section M that represent a unique ID character to be associated with this bar code type. (Refer to the Multi-Code method on page x.) ~ Configurable Codabar ID * Clear all Configurable Code Specific ID s ³ 9 0 6 6 0 0 ³ 9 9 9 9 8 3 Prefixes/Suffixes E 7

Prefixes/Suffixes E 8 SECTION E Enable STX Prefix STANDARD PREFIX CHARACTERS * Disable STX Prefix ³ 1 1 6 6 1 5 The scanner will transmit a Start of TeXt (ASCII 02H) before each bar code. ³ 1 1 6 6 0 5 Will not transmit a Start of TeXt (ASCII 02H) before each bar code. Enable Rockford-Thompson Mode * Disable Rockford- Thompson Mode ³ 1 0 5 5 1 3 ³ 1 0 5 5 0 3 Enable AIM ID Characters * Disable AIM ID Characters ³ 1 0 7 9 1 5 The scanner will transmit AIM symbology identifiers. Some scanner models may not support this feature. ³ 1 0 7 9 0 5 The scanner will not transmit AIM symbology identifiers.

SECTION E Enable UPC Prefix ID STANDARD PREFIX CHARACTERS * Disable UPC Prefix ID ³ 1 1 6 6 1 7 When enabled, the scanner will transmit a prefix before any UPC/EAN bar code. ³ 1 1 6 6 0 7 Do not send prefix ID Characters with UPC/EAN codes. The prefixes are as follows: A (UPC-A), E0 (UPC-E), F (EAN-13), and FF (EAN-8). Enable NCR Prefix ID * Disable NCR Prefix ID ³ 1 0 7 9 1 1 ³ 1 0 7 9 0 1 When enabled, the scanner will transmit a prefix before the following code types. The prefixes are as follows: A (UPC-A), E0 (UPC-E), FF (EAN-8), F (EAN-13), B1 (Code 39), B2 (ITF) and B3 (Code 128 & other codes). Prefixes/Suffixes E 9

Prefixes/Suffixes E 10 SECTION E Enable Nixdorf ID Characters STANDARD PREFIX CHARACTERS * Disable Nixdorf ID Characters ³ 1 0 7 9 1 7 This option transmits code identifiers before each bar code for many Siemens/Nixdorf registers. ³ 1 0 7 9 0 7 This option will not transmit Siemens/Nixdorf code identifiers. Enable SANYO ID Characters * Disable SANYO ID Characters ³ 1 0 7 9 1 6 Transmit Sanyo ID Characters. ³ 1 0 7 9 0 6 Do not transmit Sanyo ID Characters.

SECTION E Enable TEC Register Format ID Characters STANDARD PREFIX CHARACTERS Disable TEC Register Format ID Characters ³ 1 2 4 7 1 0 ³ 1 2 4 7 0 0 Enable TEC MA1530 ID Characters Disable TEC MA1530 ID Characters ³ 1 0 8 0 1 0 ³ 1 0 8 0 0 0 Enable Symbology Prefix Disable Symbology Prefix ³ 1 0 5 5 1 4 This option adds a symbology description in front of the bar code transmission. ³ 1 0 5 5 0 4 Do not add a symbology description in front of the bar code transmission. Prefixes/Suffixes E 11

Prefixes/Suffixes E 12 SECTION E Enable Manufacturer ID Prefix STANDARD PREFIX CHARACTERS * Disable Manufacturer ID Prefix ³ 1 0 5 5 1 2 Transmits METROLOGIC before all bar code data to identify the scanner as a Metrologic Scanner. ³ 1 0 5 5 0 2 The scanner will not transmit the manufacturer identification string. Enable C Prefix * Disable C Prefix ³ 1 0 5 5 1 1 ³ 1 0 5 5 0 1 Enable $ Prefix ID for UPC/EAN * Disable $ Prefix ID for UPC/EAN ³ 1 0 5 5 1 0 ³ 1 0 5 5 0 0

SECTION E Enable Tab Prefix STANDARD PREFIX CHARACTERS * Disable Tab Prefix ³ 1 1 6 6 1 1 The scanner will transmit a TAB (ASCII 09H) before each bar code. ³ 1 1 6 6 0 1 The scanner will not transmit a TAB. Enable SNI Beetle Mode * Disable SNI Beetle Mode ³ 1 1 6 1 1 1 ³ 1 1 6 1 0 1 Enable Cipher 1021 IDs * Disable Cipher 1021 IDs ³ 1 1 6 1 1 3 ³ 1 1 6 1 0 3 Prefixes/Suffixes E 13

Prefixes/Suffixes E 14 SECTION E STANDARD SUFFIX CHARACTERS * Enable CR Suffix Disable CR Suffix ³ 1 1 6 6 1 3 The scanner will transmit a Carriage Return after each bar code. ³ 1 1 6 6 0 3 The scanner will not transmit a Carriage Return after each bar code. * Enable LF Suffix Disable LF Suffix ³ 1 1 6 6 1 2 The scanner will transmit a Line Feed after each bar code. ³ 1 1 6 6 0 2 The scanner will not transmit a Line Feed after each bar code. This feature is Disabled when keyboard wedge defaults are loaded. Enable Tab Suffix * Disable Tab Suffix ³ 1 1 6 6 1 0 The scanner will transmit a TAB (ASCII 09H) after each bar code. ³ 1 1 6 6 0 0 The scanner will not transmit a TAB (ASCII 09H) after each bar code.

SECTION E Enable ETX Suffix STANDARD SUFFIX CHARACTERS * Disable ETX Suffix ³ 1 1 6 6 1 4 The scanner will transmit End of TeXt (ASCII 03H) after the bar code data. ³ 1 1 6 6 0 4 The scanner will not transmit End of TeXt (ASCII 03H). Enable UPC Suffix ID * Disable UPC Suffix ID ³ 1 1 6 6 1 6 The scanner will transmit a suffix after any UPC/EAN bar code. ³ 1 1 6 6 0 6 The scanner will not transmit a suffix after UPC/EAN bar codes. The suffixes are as follows: A (UPC-A), E (UPC-E), F (EAN-13) and F (EAN-8). Prefixes/Suffixes E 15

Prefixes/Suffixes E 16 SECTION E Enable Transmit of LRC Calculation LONGITUDINAL REDUNDANCY CHECK (LRC) * Disable Transmit of LCR Calculation ³ 1 0 7 8 1 1 The scanner outputs an LRC check character after the bar code. ³ 1 0 7 8 0 1 The scanner will not output an LRC (check character) after the bar code. * Start LRC on First Byte Start LRC on Second Byte ³ 1 0 7 8 0 0 The scanner will calculate the LRC check digit starting with the first character. ³ 1 0 7 8 1 0 The scanner will calculate the LRC check digit starting with the second character.

SECTION E CONFIGURABLE SUFFIXES, ALL DATA Scan the Enter/Exit Configuration Mode bar code before trying to set this feature. Refer to the Multi-Code Method on page x. Enter/Exit Configuration Mode ~ Configurable Suffix Character #1 ³ 9 9 9 9 9 9 ³ 9 0 4 5 0 0 A suffix ID can be added and assigned for data transmission. Use this code with a 3 code byte sequence from Section M that represents the desired character. ~ Configurable Suffix Character #2 ~ Configurable Suffix Character #3 ³ 9 0 4 6 0 0 Assigns a 2 nd configurable suffix character. ³ 9 0 4 7 0 0 Assigns a 3 rd configurable suffix character. Prefixes/Suffixes E 17

Prefixes/Suffixes E 18 SECTION E CONFIGURABLE SUFFIXES, ALL DATA ~ Configurable Suffix Character #4 ~ Configurable Suffix Character #5 ³ 9 0 4 8 0 0 Assigns a 4 th configurable suffix character. ³ 9 0 4 9 0 0 Assigns a 5 th configurable suffix character. While using the Multi-Code method, scan this bar code followed by the 3 code byte bar codes in Section M that represents the desired character. (Refer to the Multi-Code method on page x.) ~ Configurable Suffix Character #6 ~ Configurable Suffix Character #7 ³ 9 0 5 0 0 0 Assigns a 6 th configurable suffix character. ³ 9 0 5 1 0 0 Assigns 7 th configurable suffix character.

SECTION E ~ Configurable Suffix Character #8 CONFIGURABLE SUFFIXES, ALL DATA ~ Configurable Suffix Character #9 ³ 9 0 5 2 0 0 Assigns a 8 th configurable suffix character. ³ 9 0 5 3 0 0 Assigns a 9 th configurable suffix character. ~ Configurable Suffix Character #10 ³ 9 0 5 4 0 0 While using the Multi- Code method, scan this bar code followed by the 3 code byte bar codes in Section M that represent the desired character. (Refer to the Multi-Code method on page x.) Assigns a 10 th configurable suffix character. * Clear All User Configurable Suffixes ³ 9 9 9 9 8 4 Prefixes/Suffixes E 19

Prefixes/Suffixes E 20 SECTION E Enable SINEKO Mode SPECIAL FORMATS * Disable SINEKO Mode ³ 1 0 7 9 1 4 ³ 1 0 7 9 0 4 Enable Newcode Formatting Mode A * Disable Newcode Formatting Mode A ³ 1 1 6 7 1 1 ³ 1 1 6 7 0 1 Enable Newcode Formatting Mode B * Disable Newcode Formatting Mode B ³ 1 1 6 7 1 0 ³ 1 1 6 7 0 0

SECTION E CHARACTER REPLACEMENTS To replace a character: 1. Scan the Enter/Exit Configuration Mode bar code (located on page x, at the front of this guide). 2. Scan the Character to Replace Code (shown below). 3. Scan the ASCII Code Byte value of the character you wish to replace (refer to the ASCII reference table in Section M). 4. Scan the Replacement Character bar code. 5. Scan the ASCII Code Byte value of the replacement character. 6. Scan the Enter/Exit Configuration Mode bar code (located on page x, at the front of this guide). Character to Replace No Replacement ³ 9 3 8 6 0 0 ³ 8 3 8 6 0 0 Replacement Character ³ 9 3 8 7 0 0 Prefixes/Suffixes E 21

SECTION F * Transmit UPC-A Check Digit Do not Transmit UPC-A Check Digit UPC/EAN ³ 1 0 7 5 1 7 ³ 1 0 7 5 0 7 Transmit UPC-E Check Digit * Do Not Transmit UPC-E Check Digit ³ 1 0 7 5 1 6 ³ 1 0 7 5 0 6 Expand UPC-E to 12 Digits * Do Not Expand UPC-E To 12 Digits ³ 1 0 7 5 1 5 Expand UPC-E bar codes to the 12 digit equivalent, UPC-A bar codes. ³ 1 0 7 5 0 5 Do not expand UPC-E to the 12 digit equivalent, UPC-A bar code. Code Formatting F 1

Code Formatting F 2 SECTION F UPC/EAN Convert UPC-A to EAN-13 * Do Not Convert UPC-A to EAN-13 ³ 1 0 7 5 1 4 The scanner converts UPC-A to EAN-13 by transmitting a leading zero before the bar code. ³ 1 0 7 5 0 4 The scanner will not convert UPC-A to EAN-13. Transmit Lead Zero on UPC-E Do Not Transmit Lead Zero on UPC-E ³ 1 0 7 5 1 3 This option will transmit a zero before each UPC-E bar code. ³ 1 0 7 5 0 3 This option will not transmit a zero before each UPC-E bar code. Convert EAN-8 to EAN-13 * Do Not Convert EAN-8 to EAN-13 ³ 1 0 7 5 1 2 The scanner will transmit five zeros before the bar code to convert EAN-8 to EAN-13. ³ 1 0 7 5 0 2 The scanner will not convert EAN-8 to EAN-13.

SECTION F * Transmit UPC-A Number System UPC/EAN Do Not Transmit UPC-A Number System ³ 1 0 7 5 1 1 ³ 1 0 7 5 0 1 Metrologic strongly discourages using this feature. Duplicate numbers may result in the database. * Transmit UPC-A MFR # Do Not Transmit UPC-A MFR # ³ 1 0 7 6 1 1 ³ 1 0 7 6 0 1 * Transmit UPC-A ITEM # Do Not Transmit UPC-A ITEM # ³ 1 0 7 6 1 0 ³ 1 0 7 6 0 0 Code Formatting F 3

Code Formatting F 4 SECTION F * Transmit EAN-8 Check Digit Do Not Transmit EAN-8 Check Digit UPC/EAN ³ 1 0 7 9 1 0 ³ 1 0 7 9 0 0 * Transmit EAN-13 Check Digit Do Not Transmit EAN-13 Check Digit ³ 1 0 7 9 1 2 ³ 1 0 7 9 0 2 GTIN-14 Format No GTIN-14 Format ³ 1 0 7 5 1 0 ³ 1 0 7 5 0 0 This feature is not available with all models.

SECTION F CODABAR Transmit Codabar Start/Stop Characters * Do Not Transmit Codabar Start/Stop ³ 1 0 7 7 1 7 Transmits Codabar s start/stop characters before and after each bar code. ³ 1 0 7 7 0 7 Will not transmit Codabar s start/stop characters before and after each bar code. Convert Codabar Start/Stop Characters to Lowercase * Do Not Convert Codabar Start/Stop Characters to Lowercase ³ 1 1 5 1 1 0 ³ 1 1 5 1 0 0 Code Formatting F 5

Code Formatting F 6 SECTION F CODABAR Enable CLSI Editing ³ 1 0 7 7 1 6 CLSI type editing will be done before the information is transmitted to the host. This option will only work with 14 digit Codabar type lengths. * Do Not Enable CLSI Editing ³ 1 0 7 7 0 6 This option will not perform CLSI type editing before the information is transmitted to the host.

SECTION F CODE 39 Enable MOD 43 Check on Code 39 * Disable MOD 43 Check on Code 39 ³ 1 0 0 2 1 3 The scanner will only scan Code 39 bar codes that have a valid Modulo 43 Check Digit. ³ 1 0 0 2 0 3 The scanner will not test Code 39 bar codes for a Modulo 43 Check Digit. Transmit Mod 43 Check Digit on Code 39 * Do Not Transmit Mod 43 Check Digit on Code 39 ³ 1 0 7 7 1 5 This feature works in conjunction with Mod 43 Check on Code 39. Both must be enabled for this feature to work. ³ 1 0 7 7 0 5 This option will not transmit Code 39 s Mod 43 check character. Code Formatting F 7

Code Formatting F 8 SECTION F CODE 39 Transmit Code 39 Start/Stop Characters ³ 1 0 7 7 1 0 The scanner transmits Code 39 s start/stop characters before and after each bar code. * Do Not Transmit Code 39 Start/Stop Characters ³ 1 0 7 7 0 0 The scanner will not transmit Code 39 s start/stop characters before and after each bar code.

SECTION F Transmit Code 11 Check Digit CODE 11 AND TELEPEN * Do Not Transmit Code 11 Check Digit ³ 1 0 7 7 1 3 The scanner will transmit Code 11 check characters when used with the Enable Code 11 feature in Section A. ³ 1 0 7 7 0 3 The scanner will not transmit Code 11 check characters. Enable Convert Telepen ^L to E * Disable Convert Telepen ^L to E ³ 1 0 7 8 1 4 ³ 1 0 7 8 0 4 Code Formatting F 9

Code Formatting F 10 SECTION F Transmit UK Plessey Check Digit PLESSEY * Do Not Transmit UK Plessey Check Digit ³ 1 0 7 8 1 6 The scanner will transmit UK Plessey Check Digit characters when used with the Enable UK Plessey feature in Section A. ³ 1 0 7 8 0 6 Will not transmit UK Plessey Check Digit characters. Enable UK Plessey Special Format Disable UK Plessey Special Format ³ 1 0 7 8 1 5 ³ 1 0 7 8 0 5 Handle Incorrect UK Plessey Stop Character * Normal UK Plessey Stop Character Handling ³ 1 0 8 0 1 3 ³ 1 0 8 0 0 3

SECTION F PLESSEY * No MSI Plessey Check Digit ³ 2 0 0 7 0 4 The scanner will not test MSI Plessey bar codes for a check digit. Enable MSI Plessey MOD 10/10 Check Digit * Enable MSI Plessey MOD 10 Check Digit ³ 2 0 0 7 3 4 The scanner will test MSI Plessey bar codes for a double Modulo 10 check digit. ³ 2 0 0 7 2 4 The scanner will test MSI Plessey bar codes for a single Modulo 10 check digit. Transmit MSI Plessey Check Digit * Do Not Transmit MSI Plessey Check Digit ³ 1 0 7 7 1 1 This option works in conjunction with one or both of the Enabled MSI Plessey Mode options. ³ 1 0 7 7 0 1 The scanner will not transmit MSI Plessey s check digit characters. Code Formatting F 11

Code Formatting F 12 SECTION F 2 OF 5 Enable Mod 10 Check on ITF * Disable MOD 10 Check on ITF ³ 1 0 0 3 1 0 The scanner will only scan Interleaved 2 of 5 (ITF) bar codes that have a Modulo 10 check digit. ³ 1 0 0 3 0 0 The scanner will not test Interleaved 2 of 5 (ITF) bar codes for a Modulo 10 check digit. Transmit Mod 10 Check Digit on ITF * Do Not Transmit Mod 10 Check Digit on ITF ³ 1 0 7 7 1 4 The scanner transmits Interleaved 2 of 5 (ITF) Mod 10 check character. ³ 1 0 7 7 0 4 The scanner will not transmit Interleaved 2 of 5 (ITF) Mod 10 check digit character. This feature works in conjunction with Mod 10 check on ITF. Both must be enabled for this feature to work. Transmit Matrix 2 of 5 Check Digit * Do Not Transmit Matrix 2 of 5 Check Digit. ³ 1 0 7 8 1 2 ³ 1 0 7 8 0 2

SECTION G ENABLE RS-232 MODE * Enable RS-232 Mode ³ 4 1 5 5 5 4 When enabled the scanner will work with RS-232 ±12V serial output. RS-232 G 1

RS-232 G 2 SECTION G A parity bit is an extra data bit used to help catch data transmission errors. The scanner s parity must match the host s parity. PARITY FEATURES No Parity ³ 3 1 6 0 4 5 Odd Parity * Space Parity ³ 3 1 6 0 0 5 Select Odd Parity to set the parity bit to either 1 or 0 to ensure an odd number of bits are 1 s. ³ 3 1 6 0 1 5 Select to set the parity bit always 0. Even Parity Mark Parity ³ 3 1 6 0 2 5 Select to set the parity bit to either 1 or 0 to ensure an even number of bits are 1 s. ³ 3 1 6 0 3 5 Select to set the parity bit always 1.

SECTION G A Baud or Baud Rate is the speed at which data is transmitted. Select a Baud for the scanner that matches the host device. 115200 BAUD Rate BAUD RATES ³ 4 1 5 8 1 0 0 57600 BAUD Rate 38400 BAUD Rate ³ 4 1 5 8 9 0 ³ 4 1 5 8 8 0 19200 BAUD Rate 14400 BAUD Rate ³ 4 1 5 8 7 0 ³ 4 1 5 8 6 0 RS-232 G 3

RS-232 G 4 SECTION G BAUD RATES * 9600 BAUD Rate 4800 BAUD Rate ³ 4 1 5 8 5 0 ³ 4 1 5 8 4 0 2400 BAUD Rate 1200 BAUD Rate ³ 4 1 5 8 3 0 ³ 4 1 5 8 2 0 600 BAUD Rate 300 BAUD Rate ³ 4 1 5 8 1 0 ³ 4 1 5 8 0 0

SECTION G DATA/STOP BITS * 7 Data Bits 8 Data Bits ³ 1 1 6 0 0 3 ³ 1 1 6 0 1 3 Number of data bits transmitted for each character. 1 Stop Bit * 2 Stop Bits ³ 1 1 6 0 1 4 ³ 1 1 6 0 0 4 RS-232 G 5

RS-232 G 6 SECTION G Enable RTS/CTS Handshaking HARDWARE HANDSHAKING * Disable RTS/CTS Handshaking ³ 1 1 5 8 1 6 Output a Request to Send (RTS) signal and wait for a Clear To Send (CTS) signal before transmitting data. ³ 1 1 5 8 0 6 Do not use RTS/CTS handshaking. * Character RTS/CTS Message RTS/CTS ³ 1 1 5 8 1 5 Activate/Deactivate RTS signal for each character. ³ 1 1 5 8 0 5 Activate RTS before sending the first character and leave it active until after the last character has been transmitted. Invert RTS Polarity (RSV1) * Standard RTS Polarity ³ 1 2 4 5 1 0 +12V = Inactive -12V = Active ³ 1 2 4 5 0 0 Use standard RTS polarity -12V = Inactive +12V = Active

SECTION G Invert CTS Polarity (RSV2) HARDWARE HANDSHAKING * Standard CTS Polarity ³ 1 2 4 5 1 1 +12V = Inactive, do not send -12V = Active, OK to send ³ 1 2 4 5 0 1-12V = Inactive, do not send +12V = Active, OK to send Activate RTS, Do Not wait for CTS (RSV3) * Activate RTS, Wait for CTS ³ 1 2 4 5 1 2 Activate RTS for transmission but do not wait for CTS to send. ³ 1 2 4 5 0 2 Wait for CTS after activating RTS. Test CTS Not Present Before RTS (RSV4) * Do Not Test for CTS Present Before RTS ³ 1 2 4 5 1 3 Do not activate RTS if CTS is already present. ³ 1 2 4 5 0 3 Activate RTS without testing if CTS is already active. RS-232 G 7

RS-232 G 8 SECTION G CTS Scan Transmit HARDWARE HANDSHAKING * No CTS Scan Transmit ³ 1 2 0 4 1 7 The CTS line is used to allow a decoded bar code to be transmitted. Use reserved code 4 to ensure 1 bar code per CTS. This will prevent the scanner from gathering data until the CTS signal has been retracted. This feature is not available with all models. Enable DTR Support ³ 1 2 0 4 0 7 Do not support CTS scan transmit. * Disable DTR Support ³ 1 1 5 8 1 7 ³ 1 1 5 8 0 7 The scanner will stop scanning when the Data Terminal Ready (DTR) signal goes inactive. Enable RTS Counter Toggle * Disable RTS Counter Toggle ³ 1 1 5 9 1 5 ³ 1 1 5 9 0 5 The scanner will toggle the RTS line on a good decode.

SECTION G Enable XON/XOFF Handshaking SOFTWARE HANDSHAKING * Disable XON/XOFF Handshaking ³ 1 1 5 9 1 4 The scanner will stop transmission whenever an XOFF (ASCII 13H) is received. Transmission will resume after an XON (ASCII 11H) is received. ³ 1 1 5 9 0 4 The scanner will not test for XON/XOFF. Enable ACK/NAK * Disable ACK/NAK ³ 1 1 5 9 1 3 After transmitting data, wait for an ACK (06H) or a NAK (15H) response from the host. If ACK is received, complete the communications cycle and look for more bar codes. If NAK is received, retransmit the last set of bar code data and wait for ACK/NAK again. ³ 1 1 5 9 0 3 Do not support ACK/NAK handshaking. RS-232 G 9

RS-232 G 10 SECTION G Enable O/N Handshaking SOFTWARE HANDSHAKING Disable O/N Handshaking ³ 1 1 5 9 1 2 ³ 1 1 5 9 0 2 ACK/NAK handshaking (page G 9) must be enabled for this feature to work. Support BEL/CAN in ACK/NAK * Ignore BEL/CAN in ACK/NAK ³ 1 1 5 9 1 1 When BEL (07H) is received, the scanner beeps 3 times and exits the communications loop. If a CAN (18H) is received, then the scanner will exit the communications loop, silently. ³ 1 1 5 9 0 1 Ignore BEL/CAN characters in communication loop. Enable Razz Command Disable Razz Command ³ 1 1 8 4 1 5 When a z is received, the scanner will RAZZ once. Multiple razzes can be sounded if the character before the z is a number and is sent within 1 second of the z. The normal BEL commands must be activated for feature. ³ 1 1 8 4 0 5 Ignore z characters in communication loop.

SECTION G Enable XON/XOFF Scan Inhibit On SOFTWARE HANDSHAKING * Disable XON/XOFF Scan Inhibit Off ³ 1 1 6 0 1 1 This feature is not available with all models. ³ 1 1 6 0 0 1 This feature is not available with all models. Enable 5 Retries on ACK/NAK Time Out * Disable 5 Retries on ACK/NAK Time Out ³ 1 1 8 0 1 3 Allow up to 5 NAK retransmissions of the data before dropping out of the communications loop. ³ 1 1 8 0 0 3 Do not limit retransmission to 5 NAK cycles. Enable 5 NAK Retries Disable 5 NAK Retries ³ 1 1 5 8 1 4 ³ 1 1 5 8 0 4 RS-232 G 11

RS-232 G 12 SECTION G Enable French PC Term MISCELLANEOUS * Disable French PC Term ³ 1 1 6 1 1 0 The scanner transmits PC type make/break scan codes instead of ASCII data characters. The scan codes match a WYSE French PC Terminal Emulation. ³ 1 1 6 1 0 0 Do not transmit in French PC Term Mode. Enable USA Wyse PC Disable USA Wyse PC ³ 1 1 6 1 1 7 Enables USA Wyse PC style keyboard PCTERM mode. ³ 1 1 6 1 0 7 Disables USA Wyse PC style keyboard PCTERM mode. * Enable Receive Data Disable Receive Data ³ 1 2 5 0 0 6 ³ 1 2 5 0 1 6 Disable receive port after 5 seconds.

SECTION H ENABLE KEYBOARD EMULATION Load Keyboard Wedge Defaults ³ 9 9 9 9 9 4 Loads default settings for keyboard wedge mode. Enable Stand-Alone Keyboard Emulation * Enable Keyboard Wedge Emulation ³ 5 1 5 5 1 5 3 Use this with special standalone models that are not cabled for an external keyboard. When the Stand- Alone Mode is enabled, the scanner will send keyboard power on information and configure hardware to simulate a constant keyboard connection. ³ 5 1 5 5 1 4 3 Use this with an external keyboard. Transmit in wedge mode to allow standard PC keyboards to communicate when no bar code data is available. Keyboard H 1

Keyboard H 2 SECTION H COUNTRY/SCAN CODE TABLE SELECTS * USA Keyboard Switzerland Keyboard ³ 4 1 6 2 6 0 Enable USA Keyboard. ³ 4 1 6 2 8 0 Enable Swiss Keyboard Spain Keyboard Italy Keyboard ³ 4 1 6 2 5 0 Enable Spanish Keyboard ³ 4 1 6 2 4 0 Enable Italian Keyboard Germany Keyboard France Keyboard ³ 4 1 6 2 3 0 Enable German Keyboard ³ 4 1 6 2 2 0 Enable French Keyboard

SECTION H UK Keyboard COUNTRY/SCAN CODE TABLE SELECTS Belgium Keyboard ³ 4 1 6 2 1 0 Enable UK Keyboard. ³ 4 1 6 2 0 0 Enable Belgium Keyboard Japanese Keyboard IBM 4700 Financial Keyboard ³ 4 1 6 2 1 0 0 Enable Japanese Keyboard ³ 4 1 6 2 7 0 Enable IBM 4700 Financial Keyboard Sweden/Finland Keyboard ³ 4 1 6 2 9 0 Enable Sweden/Finland Keyboard Keyboard H 3

Keyboard H 4 SECTION H KEYBOARD/SYSTEM TYPE * AT Keyboard XT Keyboard ³ 2 1 6 2 1 5 If using an AT computer, scan the above bar code. (Includes IBM PS/2 and compatible models 50, 55, 60, 80) ³ 2 1 6 2 0 5 If using an XT computer, scan the above bar code. PS/2 Keyboard Terminal KB Emulation ³ 2 1 6 2 2 5 Scan the above code for PS/2 computer. (Includes IBM PC and compatible models 30, 70 and 8556) ³ 2 1 6 2 3 5 Scan the above code to enable terminal keyboard emulation mode.

SECTION H Transmit Make Code Only SPECIAL KEYBOARD FEATURES * Transmit Make/Break Code ³ 1 1 6 3 1 1 Do not scan unless instructed by a Metrologic representative. ³ 1 1 6 3 0 1 Do not scan unless instructed by a Metrologic representative. Do Not Transmit F0H Break Code * Transmit F0H Break Code ³ 1 1 6 3 0 0 The scanner will not transmit the F0H in the break-code sequence. ³ 1 1 6 3 1 0 The scanner will transmit the F0H in the break-code sequence. Transmit Cleanup Bit * Do Not Transmit Cleanup Bit ³ 1 1 6 3 1 5 ³ 1 1 6 3 0 5 Use for certain NEC computers. Keyboard H 5

Keyboard H 6 SECTION H Enable Alt Mode SPECIAL KEYBOARD FEATURES * Disable Alt Mode ³ 1 1 6 2 1 7 The scanner will duplicate the following keyboard sequence: Hold down ALT key and Type decimal number that corresponds to the appropriate character. ³ 1 1 6 2 0 7 Caution: If the host software application uses the right ALT key as a Hot key, ALT mode must be disabled. Enable Auto Detect Mode (AT/PS2) * Disable Auto Detect Mode (AT/PS2) ³ 1 1 6 2 1 4 Automatically detects caps lock status. ³ 1 1 6 2 0 4 The Auto Detect Caps Lock feature is not supported.

SECTION H Enable Caps Lock (XT) SPECIAL KEYBOARD FEATURES * Disable Caps Lock (XT) ³ 1 1 6 2 1 4 ³ 1 1 6 2 0 4 The Caps Lock feature is not supported. Send Numbers as Keypad Data * Send Numbers as Normal Data ³ 1 1 6 3 1 6 ³ 1 1 6 3 0 6 All data is sent as if it has been entered on a keypad. Enable Reserved Feature * Disable Reserved Feature ³ 1 1 6 4 1 0 ³ 1 1 6 4 0 0 Keyboard H 7

Keyboard H 8 SECTION H SPECIAL KEYBOARD FEATURES * Use Extended ASCII to Send Extended Key Codes Use Extended ASCII Characters as Extended ASCII ³ 1 1 6 3 0 3 Use extended ASCII characters to send PC keyboard keys such as F1, F2, etc See section M for details. ³ 1 1 6 3 1 3 Transmit extended ASCII codes via ALT mode. * Character KB Inhibit Message KB Inhibit ³ 1 1 6 3 0 4 ³ 1 1 6 3 1 4

SECTION H Inter-Scan Code Delay 800 Microseconds INTER-SCAN CODE DELAYS Inter-Scan Code Delay 7.5 msec ³ 8 1 6 5 8 0 The time specified represents the amount of time between individual 9 bit-scan codes. This parameter may need to be adjusted for operation with certain PC keyboard BIOS. ³ 8 1 6 5 7 5 0 The time specified represents the amount of time between individual 9 bit-scan codes. This parameter may need to be adjusted for operation with certain PC keyboard BIOS. Inter-Scan Code Delay 15 msec ~ Variable Inter-Scan Code Delay msec ³ 8 1 6 5 1 5 0 0 The time specified represents the amount of time between individual 9 bit-scan codes. ³ 9 1 6 5 0 0 Refer to the Multi-Code Configuration method on page x. This parameter may need to be adjusted for operation with certain PC keyboard BIOS. Keyboard H 9

Keyboard H 10 SECTION H CONTROL SETS In general, standard bar code symbologies will only encode the ASCII character set. Function keys, arrow keys and many other extended keys on an IBM compatible keyboard do not translate to ASCII characters. One method of bar coding the extended keys is to substitute the extended key codes when a specific ASCII control character found in the bar code stream. The Control Sets are specific translation of the ASCII (HEX) set. CONTROL SET #1 Enable Control Set #1 ³ 4 1 6 4 8 4 Disable Control Set #1 ³ 4 1 6 4 0 4

SECTION H CONTROL SET #1 ASCII (HEX) ASCII Control Extended Key 00H Null Numeric Keypad 01H SOH Num Lock 02H STX Down 03H ETX Numeric Keypad 04H EOT Insert 05H ENQ Delete 06H ACK System Request 07H BEL 08H BS 09H TAB Tab 0AH LF Caps Lock 0BH VT Shift Tab 0CH FF Alt 0DH CR Enter 0EH SO Control 0FH SI Up Arrow 10H DLE F1 11H DC1 F2 12H DC2 F3 13H DC3 F4 14H DC4 F5 15H NAK F6 16H SYN F7 17H ETB F8 18H CAN F9 19H EM F10 1AH SUB Home 1BH ESC Esc 1CH FS Page Up 1DH GS Page Down 1EH RS Print Screen 1FH US End Keyboard H 11

Keyboard H 12 SECTION H 3151 TERMINAL KEYBOARD * 3151 Terminal Keyboard ³ 3 1 6 4 0 0

SECTION I OCIA Load OCIA Defaults Enable OCIA ³ 9 9 9 9 9 3 ³ 4 1 5 5 4 4 Select this option if communications require OCIA (Optically Coupled Interface Adapter). This serial interface is clocked by the host. Enable DTS/Siemens * Enable DTS/Nixdorf ³ 2 1 7 7 0 6 ³ 2 1 7 7 1 6 Enable NCR-S Enable NCR-F ³ 2 1 7 7 3 6 ³ 2 1 7 7 2 6 OCIA I 1

SECTION J LIGHT PEN Enable Light Pen Mode ³ 4 1 5 5 2 4 Select this option if the scanner will be used in place of a light pen. It provides light pen emulation of each bar code scanned. * Bars High Spaces High ³ 1 1 6 9 1 7 ³ 1 1 6 9 0 7 Transmit Code 39 * Transmit as Scanned ³ 1 1 6 9 1 6 All bar codes will be decoded then transmitted as code 39 bar codes. ³ 1 1 6 9 0 6 All bar codes will be decoded and transmitted in their original symbology. Light Pen/Laser Emulation J 1

Light Pen/Laser Emulation J 2 SECTION J Poll Light Pen Source LIGHT PEN/SET NARROW ELEMENT BORDER * Do Not Poll Light Pen Source ³ 1 1 6 9 1 5 The scanner waits for an active source voltage before transmitting data. ³ 1 1 6 9 0 5 The scanner will not wait for an active source voltage before transmitting data. Enable Light Pen Extra Toggle * Disable Light Pen Extra Toggle ³ 1 1 6 9 1 1 ³ 1 1 6 9 0 1 The scanner beeps and toggles the light pen data line with an extra data pulse to condition the decoder. 10x Narrow Element Border * 50x Narrow Element Border ³ 1 1 6 9 1 2 This bar code allows the transmission of Light Pen/Wand emulation using a 10x border. ³ 1 1 6 9 0 2 This bar code allows the transmission of Light Pen/Wand emulation using a 50x border.

SECTION J SET NARROW ELEMENT WIDTH /LASER EMULATION * 1 ms Narrow Element Width 60 µs Narrow Element Width ³ 8 1 6 8 1 6 3 0 This option allows the transmission of Light/Pen Wand emulation a 1 ms narrow element width. ³ 8 1 6 8 1 0 0 This transmits at 60 µs narrow element width. 100 µs Narrow Element Width 500 µs Narrow Element Width ³ 8 1 6 8 1 6 0 This transmits at 100 µs narrow element width. ³ 8 1 6 8 8 2 0 This transmits at 500 µs narrow element width. ~ Variable Narrow Element Width Laser Emulation Refer to the Multi-Code Method on page x. ³ 9 1 6 8 0 0 ³ 9 9 9 9 7 9 Sets the minimum x-dimension in 6 µs increments. Scan this code followed by a 3 digit code byte sequence found in Section M. Light Pen/Laser Emulation J 3

SECTION K Load IBM 46xx Defaults IBM 46XX CONFIGURATION/IBM PORTS Enable IBM 46xx Communication ³ 9 9 9 9 9 5 Load default format settings for IBM 46xx systems. ³ 4 1 5 5 0 4 Select this option for IBM 46xx SIOC/RS485 communication. Not all scanners support this interface. The correct interface board is required. IBM Port 17B 3687-2 In Counter IBM Port 5B 1520 HH Laser ³ 3 1 7 2 5 0 ³ 3 1 7 2 6 0 * IBM Port 9B 4500 CCD HH BCR1 IBM Port 9B 4501 CCD HH BCR2 ³ 3 1 7 2 7 0 ³ 3 1 7 2 3 0 IBM 46xx Configuration K 1

IBM 46xx Configuration K 2 SECTION K IBM RESERVE CODES IBM Reserve #1 IBM Reserve #2 ³ 3 1 7 2 0 0 ³ 3 1 7 2 1 0 IBM Reserve #3 ³ 3 1 7 2 2 0 IBM Reserve #5 ³ 3 1 7 2 4 0

SECTION M CODE BYTE USAGE User configurable prefixes, symbol length and other features that use these code bytes for configuration, require that the scanner be in configuration mode. Scan the Enter/Exit Configuration Mode bar code before starting the configuration cycle. Single code configuration mode does not work for these multi-code sequences. Enter/Exit Configuration Mode ³ 9 9 9 9 9 9 EXAMPLE User configurable prefix/suffix characters (Section E) can be saved into the scanner by scanning the 3 digit decimal equivalent of the ASCII character into the appropriate character location with the code byte bar codes. To add an asterisk (*) as a prefix scan the following bar codes in order: 1. Enter/Exit Configuration Mode (3 beeps) 2. Configurable Prefix 1 (1 beep) 3. Code Byte 0 (1 beep) 4. Code Byte 4 (2 beeps) 5. Code Byte 2 (3 beeps) 6. Enter/Exit Configuration Mode (3 beeps) Code Bytes M 1

Code Bytes M 2 SECTION M CODE BYTES 0-5 Code Byte 0 Code Byte 1 ³ 0 ³ 1 Code Byte 2 Code Byte 3 ³ 2 ³ 3 Code Byte 4 Code Byte 5 ³ 4 ³ 5

SECTION M CODE BYTES 6-9 Code Byte 6 Code Byte 7 ³ 6 ³ 7 Code Byte 8 Code Byte 9 ³ 8 ³ 9 Code Bytes M 3

Code Bytes M 4 SECTION M RESERVED CODES ~ Enable Reserved Code ³ 9 9 9 9 8 8 Contact a Metrologic customer service representative for additional details on this feature. ~ Disable Reserved Code ³ 9 9 9 9 8 7

SECTION M CODE BYTE/CODE TYPE TABLE CODE BYTE CODE TYPES 004 UPC-A 002 UPC-E 003 EAN-8 005 EAN-13 080 Code 39 081 Codabar 082 Interleaved 2 of 5 083 Code 128 084 Code 93 091 MSI Plessey 092 Code 11 093 Airline 2 of 5 (15 digits) 094 Matrix 2 of 5 095 Telepen 096 UK Plessey 098 Standard 2 of 5 097 Airline (13 digits) 099 TRI-OPTIC Code Bytes M 5

Code Bytes M 6 SECTION M ASCII REFERENCE TABLE HEX VALUE DECIMAL VALUE/ CODE BYTE VALUE CHARACTER CONTROL KEYBOARD EQUIVALENT 00 000 NUL @ 01 001 SOH A 02 002 STX B 03 003 ETX C 04 004 EOT D 05 005 ENQ E 06 006 ACK F 07 007 BEL G 08 008 BS H 09 009 HT I 0A 010 LF J 0B 011 VT K 0C 012 FF L 0D 013 CR M 0E 014 SO N 0F 015 SI O 10 016 DLE P 11 017 DC1 Q 12 018 DC2 R 13 019 DC3 S 14 020 DC4 T 15 021 NAK U 16 022 SYN V 17 023 ETB W 18 024 CAN X 19 025 EM Y 1A 026 SUB Z

SECTION M ASCII REFERENCE TABLE HEX VALUE DECIMAL VALUE/ CODE BYTE VALUE CHARACTER CONTROL KEYBOARD EQUIVALENT 1B 027 ESC [ 1C 028 FS \ 1D 029 GS ^ 1E 030 RS _ 1F 031 US 20 032 SP space, blank 21 033! 22 034 23 035 # 24 036 $ 25 037 % 26 038 & 27 039 apostrophe 28 040 ( 29 041 ) 2A 042 * 2B 043 + 2C 044, comma 2D 045 - minus 2E 046. period 2F 047 / 30 048 0 number zero 31 049 1 number one 32 050 2 33 051 3 34 052 4 35 053 5 Code Bytes M 7

Code Bytes M 8 SECTION M ASCII REFERENCE TABLE HEX VALUE DECIMAL VALUE/ CODE BYTE VALUE CHARACTER CONTROL KEYBOARD EQUIVALENT 36 054 6 37 055 7 38 056 8 39 057 9 3A 058 : 3B 059 ; 3C 060 < less than 3D 061 = 3E 062 > greater than 3F 063? 40 064 @ shift P 41 065 A 42 066 B 43 067 C 44 068 D 45 069 E 46 070 F 47 071 G 48 072 H 49 073 I letter l 4A 074 J 4B 075 K 4C 076 L 4D 077 M 4E 078 N

SECTION M ASCII REFERENCE TABLE HEX VALUE DECIMAL VALUE/ CODE BYTE VALUE CHARACTER CONTROL KEYBOARD EQUIVALENT 4F 079 O letter O 50 080 P 51 081 Q 52 082 R 53 083 S 54 084 T 55 085 U 56 086 V 57 087 W 58 088 X 59 089 Y 5A 090 Z 5B 091 [ shift K 5C 092 \ shift L 5D 093 ] shift M 5E 094 ^, shift N 5F 095 _, shift 0, underscore 60 096 accent grave 61 097 a 62 098 b 63 099 c 64 100 d 65 101 e 66 102 f 67 103 g 68 104 h 69 105 i Code Bytes M 9

Code Bytes M 8 SECTION M ASCII REFERENCE TABLE HEX VALUE DECIMAL VALUE/ CODE BYTE VALUE CHARACTER CONTROL KEYBOARD EQUIVALENT 36 054 6 37 055 7 38 056 8 39 057 9 3A 058 : 3B 059 ; 3C 060 < less than 3D 061 = 3E 062 > greater than 3F 063? 40 064 @ shift P 41 065 A 42 066 B 43 067 C 44 068 D 45 069 E 46 070 F 47 071 G 48 072 H 49 073 I letter l 4A 074 J 4B 075 K 4C 076 L 4D 077 M 4E 078 N

SECTION M EXTENDED KEY CODE REFERENCE TABLE KEY AT SCAN CODE PS2 SCAN CODE 3151 PREFIX/SUFFIX VALUE HEX = DECIMAL 75H 48H 63H 80H = 128 72H 50H 60H 81H = 129 74H 4DH 6AH 82H = 130 6BH 4BH 61H 83H = 131 Insert 70H 52H 67H 84H = 132 Delete 71H 53H 64H 85H = 133 Home 6CH 47H 6EH 86H = 134 End 69H 4FH 00H 87H = 135 Page Up 7DH 49H 00H 88H = 136 Page Down 7AH 51H 00H 89H = 137 Right Alt 11H 38H 00H 8AH = 138 Right Ctrl 14H 1DH 39H 8BH = 139 Reserved 00H 00H 00H 8CH = 140 Reserved 00H 00H 00H 8DH = 141 Numeric Keypad Enter 5AH 1CH 79H 8EH = 142 Numeric Keypad / 4AH 35H 00H 8FH = 143 F1 05H 3BH 07H 90H = 144 F2 06H 3CH 0FH 91H = 145 F3 04H 3DH 17H 92H = 146 F4 0CH 3EH 1FH 93H = 147 F5 03H 3FH 27H 94H = 148 F6 0BH 40H 2FH 95H = 149 F7 83H 41H 37H 96H = 150 F8 0AH 42H 3FH 97H = 151 F9 01H 43H 47H 98H = 152 F10 09H 44H 4FH 99H = 153 F11 78H 57H 56H 9AH = 154 F12 07H 58H 5EH 9BH = 155 Numeric + 79H 4EH 00H 9CH = 156 Code Bytes M 11

Code Bytes M 12 SECTION M EXTENDED KEY CODE REFERENCE TABLE KEY AT SCAN CODE PS2 SCAN CODE 3151 PREFIX/SUFFIX VALUE HEX = DECIMAL Numeric - 7BH 4AH 7CH 9DH = 157 Numeric * 7CH 37H 00H 9EH = 158 Caps Lock 58H 3AH 14H 9FH = 159 Num Lock 77H 45H 00H A0H = 160 Left ALT 11H 38H 00H A1H = 161 Left CTRL 14H 1DH 11H A2H = 162 Left Shift 12H 2AH 12H A3H = 163 Right Shift 59H 36H 59H A4H = 164 Print Screen Multiple 00H 00H A5H = 165 Tab 0DH 0FH 0DH A6H = 166 Shift Tab 8DH 8FH 65H A7H = 167 Enter 5AH 1CH 5AH A8H = 168 ESC 76H 01H 08H A9H = 169 Left ALT Make 11H 36H 00H AAH = 170 Left ALT Break 11H B6H 00H ABH = 171 Left CTRL Make 14H 1DH 00H ACH = 172 Left CTRL Break 14H 9DH 00H ADH = 173 * Left ALT + 1 character 11H 36H 00H AEH = 174 * Left CTRL + 1 character 14H 1DH 00H AFH = 175 * Send 58H C0H = 192 Clear 6FH C1H = 193 Jump 76H C2H = 194 Send Line 7EH C3H = 195 Erase EOF 6DH C4H = 196 Send - Make Only 58H C5H = 197 * Example: 1 st Configurable Prefix = 174 2 nd Configurable Prefix = 065 Scanner will transmit <left ALT Make> A <Left ALT Break>

SECTION N CUSTOM DEFAULTS Metrologic manufactures several scanners for OEM applications. These scanners may use a different set of defaults than the standard Metrologic factory defaults. Scanning the following bar codes will restore the default factory settings. Enable Factory Defaults ³ 8 4 6 6 0 0 Scan this code followed by the Recall Defaults code to enable and load Metrologic factory defaults. Recall Defaults ³ 9 9 9 9 9 8 Miscellaneous Features N 1

Miscellaneous Features N 2 SECTION N Ruby Verifone Defaults CUSTOM DEFAULTS RCH ³ 8 4 6 6 1 2 8 0 Scan this code followed by the Recall Defaults code to enable and load Ruby Verifone Defaults. ³ 8 4 6 6 1 0 Scan this code followed by the Recall Defaults code to enable and load RCH Defaults. Sanyo Gilbarco ³ 8 4 6 6 0 2 0 Scan this code followed by the Recall Defaults code to enable and load Sanyo Defaults. ³ 8 4 6 6 3 0 Scan this code followed by the Recall Defaults code to enable and load Gilbarco Defaults. ALT Defaults MS6750 Defaults ³ 8 4 6 6 0 0 4 0 Scan this code followed by the Recall Defaults code to enable and load ALT Defaults. ³ 8 4 6 6 0 0 8 0 Scan this code followed by the Recall Defaults code to enable and load MS6750 Defaults.

SECTION N CUSTOM DEFAULTS German Post Defaults ³ 8 4 6 6 0 0 9 0 Scan this code followed by the Recall Defaults code to enable and load German Post Defaults. Custom Keyboard FR1 ³ 9 9 7 0 0 0 Custom Terminal FR1 ³ 9 9 7 0 0 1 Miscellaneous Features N 3

Miscellaneous Features N 4 SECTION N SERIAL PROGRAM MODE For Serial Program Mode, all commands must be framed by an STX (02 Hex) and ETX (03 Hex). To recall defaults: 1. Transmit <STX>999999<ETX> through the Serial Port. This will put the scanner in serial program mode. Scanning will be suspended and the scanner will respond with an ACK (06 Hex). 2. Transmit <STX>999998<ETX> through the Serial Port. This is the Recall Default bar code in the MetroSelect guide. The scanner will respond with an ACK (06 Hex). 3. Transmit <STX>999999<ETX> through the Serial Port. This will cause the scanner to exit program mode and save the new settings. The scanner will beep 3 times and send an ACK (06 Hex). If at anytime, the scanner cannot recognize a command, it will respond with a NAK (15 Hex). SOFTWARE/SERIAL NUMBER Software Number Scanner Information ³ 9 9 9 9 6 5 The scanner will transmit its software revision. ³ 9 9 9 9 2 8 This barcode will transmit the main & interface coprocessor software numbers as well as the scanner s serial number. The data is output as barcode (formatted) data (ie. 15xxx/15xxx/9876543210, where x represents any nonnumbered value).

SECTION O DISABLE AUXILIARY PORT * Disable AUX Port ³ 4 3 7 3 0 0 AUX PORT AND SECONDARY DEVICE DATA FORMATS The following section includes features that are not available with all Metrologic scanner models. Please contact a customer service representative for additional information and technical assistance. When using a Metrologic device as a secondary: Follow Step 1 to configure the auxiliary port to accept a Metrologic scanner as the secondary scanner. Then follow Step 2 to configure the secondary scanner to match the auxiliary port s data format. If the secondary scanner is not a Metrologic scanner go to page 3 and follow the instructions under When using a non-metrologic RS-232 Device as a secondary. The auxiliary input port s data format must match the main output format of the secondary scanner. Step 1: Scan the following bar code to enable the auxiliary port on the primary scanner. AUX Port Data Format ³ 4 3 7 3 3 0 Auxiliary Port Controls O 1

Auxiliary Port Controls O 2 SECTION O AUX PORT AND SECONDARY DEVICE DATA FORMATS Step 2: Then scan the following bar codes, in order, to configure the secondary scanner. 1. Enable AUX Output 2. Secondary Scanner Data Format ³ 1 2 4 8 1 7 ³ 4 3 7 5 3 0 3. Enable Comm Timeouts 4. Turn OFF Auxiliary Scanner s Beeper (Optional) ³ 1 1 8 4 1 2 ³ 3 1 8 5 0 5

SECTION O AUX PORT AND SECONDARY DEVICE DATA FORMATS The following section includes features that are not available with all Metrologic scanner models. Please contact a customer service representative for additional information and technical assistance. When using a non-metrologic RS-232 device as a secondary: Scan the following bar code to enable the auxiliary port on the primary scanner. AUX Port General RS-232 Format ³ 4 3 7 3 1 0 The auxiliary input port s data format must match the main output format of the secondary device. The secondary device must be capable of RTS/CTS handshaking and have a carriage return (ASCII 0DH) terminator on the data. The default settings for the AUX Port General RS-232 Format are: 38400 baud 7 data bits 2 stop bits Space parity Auxiliary Port Controls O 3

Auxiliary Port Controls O 4 SECTION O ADDITIONAL AUXILIARY PORT DATA FORMATS The auxiliary input port s data format must match the main output format of the secondary device. Enable AUX Port with UPC Supplemental Data Format Enable AUX Port with Code Select Data Format ³ 4 3 7 3 4 0 ³ 4 3 7 3 5 0 Enable AUX Port with Tech 7, 8 Data Format Enable AUX Port with Reserved 2 Data Format ³ 4 3 7 3 6 0 ³ 4 3 7 3 8 0 Enable AUX Port with Reserved 3 Data Format Enable AUX Port with Reserved 1 Data Format ³ 4 3 7 3 7 0 ³ 4 3 7 3 9 0

SECTION O ADDITIONAL AUXILIARY PORT DATA FORMATS Enable AUX Port with Stratos Decode Data Format ³ 4 3 7 3 2 0 Auxiliary Port Controls O 5

Auxiliary Port Controls O 6 SECTION O AUX 115200 Baud Rate AUXILIARY PORT BAUD RATES AUX 57600 Baud Rate ³ 4 3 7 0 1 0 0 ³ 4 3 7 0 9 0 AUX 38400 Baud Rate AUX 19200 Baud Rate ³ 4 3 7 0 8 0 ³ 4 3 7 0 7 0 AUX 14400 Baud Rate AUX 9600 Baud Rate ³ 4 3 7 0 6 0 ³ 4 3 7 0 5 0

SECTION O AUX 4800 Baud Rate AUXILIARY PORT BAUD RATES AUX 2400 Baud Rate ³ 4 3 7 0 4 0 ³ 4 3 7 0 3 0 AUX 1200 Baud Rate AUX 600 Baud Rate ³ 4 3 7 0 2 0 ³ 4 3 7 0 1 0 AUX 300 Baud Rate ³ 4 3 7 0 0 0 Auxiliary Port Controls O 7

Auxiliary Port Controls O 8 SECTION O AUXILIARY PORT PARITY AUX No Parity ³ 3 3 7 2 4 5 AUX Mark Parity * AUX Space Parity ³ 3 3 7 2 3 5 ³ 3 3 7 2 1 5 AUX Even Parity AUX Odd Parity ³ 3 3 7 2 2 5 ³ 3 3 7 2 0 5

SECTION O AUX 1 Stop Bit AUXILIARY PORT STOP BITS/DATA BITS * AUX 2 Stop Bits ³ 1 3 7 2 1 4 ³ 1 3 7 2 0 4 * AUX 7 Data Bits AUX 8 Data Bits ³ 1 3 7 2 0 3 ³ 1 3 7 2 1 3 Auxiliary Port Controls O 9

Auxiliary Port Controls O 10 SECTION O AUXILIARY RTS/CTS AND MODE 7 * Enable AUX RTS/CTS Handshaking Disable AUX RTS/CTS Handshaking ³ 1 3 7 0 1 6 ³ 1 3 7 0 0 6 Message AUX RTS/CTS * Character AUX RTS/CTS ³ 1 3 7 0 0 5 ³ 1 3 7 0 1 5 Enable AUX Port Mode 7 Disable AUX Port Mode 7 ³ 4 3 7 3 7 0 ³ 4 3 7 3 1 0 Mode 7 enables reception of prefix and suffix codes when AUX port RTS/CTS handshaking is disabled.

SECTION O Enable AUX D/E Commands AUXILIARY D/E, F/L, AND M/O * Disable AUX D/E Commands ³ 1 3 7 1 1 7 ³ 1 3 7 1 0 7 Enable AUX F/L Commands * Disable AUX F/L Commands ³ 1 3 7 1 1 6 ³ 1 3 7 1 0 6 Enable AUX M/O Commands * Disable AUX M/O Commands ³ 1 3 7 1 1 5 ³ 1 3 7 1 0 5 Auxiliary Port Controls O 11

Auxiliary Port Controls O 12 SECTION O * Enable AUX XON/XOFF Handshaking AUXILIARY XON/XOFF AND ACK/NAK Disable AUX XON/XOFF Handshaking ³ 1 3 7 1 1 4 ³ 1 3 7 1 0 4 * Enable AUX ACK/NAK Commands Disable AUX ACK/NAK Commands ³ 1 3 7 1 1 3 ³ 1 3 7 1 0 3

SECTION O * Normal AUX CTS Polarity AUXILIARY CTS AND RTS POLARITY Flip AUX CTS Polarity ³ 1 3 7 3 0 7 ³ 1 3 7 3 1 7 * Normal AUX RTS Polarity Flip AUX RTS Polarity ³ 1 3 7 3 0 6 ³ 1 3 7 3 1 6 AUXILIARY SAME SYMBOL TIMEOUT * AUX has Same Symbol Timeout No AUX Same Symbol Timeout ³ 1 3 7 3 0 4 This feature skips the same symbol timeout in the master when the auxiliary scanner scans (or repeats) faster than the same symbol timeout in the master scanner. ³ 1 3 7 3 1 4 Metrologic recommends turning off the auxiliary scanner s beep if the AUX Same Symbol Timeout feature is disabled. Auxiliary Port Controls O 13

Auxiliary Port Controls O 14 SECTION O MAIN OUTPUT PORT AUXILIARY DATA FORMATS When a scanner is used as a secondary scanner to another scanner s auxiliary input, the output data can be in one of the following formats. Reserve Code 32 ³ 1 2 4 8 1 7 This is a quick method for setting reserve Code 32 in the secondary scanner using HoloTrak Decode Data Format. This code should not be used for the MS6720. * HoloTrak Decode Output AUX Data Format UPC Supplemental Output AUX Data Format ³ 4 3 7 5 0 0 ³ 4 3 7 5 4 0 Stratos Decode Output AUX Data Format Code Select Output AUX Data Format ³ 4 3 7 5 2 0 ³ 4 3 7 5 5 0

SECTION O TECH 7 & 8 Output AUX Data Format MAIN OUTPUT PORT AUXILIARY DATA FORMATS Reserved 1 Output AUX Data Format ³ 4 3 7 5 6 0 ³ 4 3 7 5 9 0 Reserved 2 Output AUX Data Format Reserved 3 Output AUX Data Format ³ 4 3 7 5 8 0 ³ 4 3 7 5 7 0 Auxiliary Port Controls O 15

Auxiliary Port Controls O 16 SECTION O No AUX Port Inter-Character Delays INTER-CHARACTER DELAYS * 1 msec AUX Port Inter-Character Delay ³ 8 3 7 6 0 0 ³ 8 3 7 6 1 0 10 msec AUX Port Inter-Character Delay 25 msec AUX Port Inter-Character Delay ³ 8 3 7 6 1 0 0 ³ 8 3 7 6 2 5 0 ~ Variable AUX Port Inter-Character Delay ³ 9 3 7 6 0 0 The Delay between characters being sent out of the auxiliary port can be set in 1 millisecond increments by scanning the Variable AUX Port Inter-character Delay barcode followed by a 3 character sequence of code bytes that range from 001 to 255 milliseconds. Refer to the Multi-Code Configuration Method on page x.

SECTION P FULL SPEED USB Enable Full Speed USB Full Speed USB Defaults ³ 4 1 5 5 1 2 4 ³ 9 9 9 9 7 1 Adds the ability to encode scanner serial number in NOVRAM. Load Integrated Full Speed USB Defaults ³ 9 9 9 9 7 0 USB P 1

USB P 2 SECTION P FULL SPEED USB The following codes can be used if the Full Speed USB Default bar code has not been scanned. Enable USB IBM ID * Disable USB IBM ID ³ 1 1 7 8 1 7 ³ 1 1 7 8 0 7 * Enhanced Code ID s * Legacy Code IDs ³ 1 1 7 8 0 4 ³ 1 1 7 8 1 4 RS232 of USB Out * Normal USB Out ³ 1 1 7 8 1 6 ³ 1 1 7 8 0 6

SECTION P FULL SPEED USB The following codes can be used if the Full Speed USB Default bar code has not been scanned. Scanner 4A00h Flatbed Scanner 4B00h Handheld ³ 3 1 6 4 0 0 1 0 ³ 3 1 6 4 0 0 3 0 4A00h/6E00h Tabletop Scanner/Scale ³ 3 1 6 4 0 0 4 0 USB P 3

USB P 4 SECTION P Enable Low Speed USB LOW SPEED USB Load Low Speed External USB Defaults ³ 4 1 5 5 1 1 4 ³ 9 9 9 9 7 8 Load Low Speed Internal USB Defaults ³ 9 9 9 9 4 1 The following codes only apply to scanners with internal Low-Speed USB interfaces and specific software versions. Please contact a Metrologic representative for additional information on the use and restrictions of these bar codes. USB Serial Emulation Mode USB Keyboard Emulation Mode ³ 3 1 6 4 7 0 ³ 3 1 6 4 0 0

SECTION R IS3480 / MS3580 / MS3780 The following bar codes are specific to the IS3480, MS3580 and the MS3780 unless otherwise noted. Button Modes * Button Click Pattern Switching Mode Button Hold Pattern Switching Mode ³ 1 2 3 8 0 6 ³ 1 2 3 8 1 6 Button Click Delay 15 Second Time Out 10 Second Time Out ³ 4 2 3 8 3 0 0 ³ 4 2 3 8 2 0 0 * 5 Second Time Out ³ 4 2 3 8 1 0 0 IS3480 / MS3580 / MS3780 R 1

IS3480 / MS3580 / MS3780 R 2 SECTION R IS3480 / MS3580 / MS3780 The following bar codes are specific to the IS3480, MS3580 and the MS3780 unless otherwise noted. Primary Scan Patterns Secondary Scan Patterns * Primary Omni Secondary Omni ³ 9 9 9 9 4 7 This bar code sets the primary pattern to all scan lines on for omnidirectional reading. ³ 9 9 9 9 4 4 This bar code sets the secondary pattern to all scan lines on for omnidirectional reading. Primary Raster Secondary Raster ³ 9 9 9 9 4 6 This bar code sets the primary pattern to horizontal raster. ³ 9 9 9 9 4 3 This bar code sets the secondary pattern to horizontal raster. Primary Single-Line Secondary Single-Line ³ 9 9 9 9 4 5 This bar code sets the primary pattern to single-line for menu reading. ³ 9 9 9 9 4 2 This bar code sets the secondary pattern to singleline for menu reading.

SECTION R IS3480 / MS3580 / MS3780 The following bar codes are specific to the IS3480, MS3580 and the MS3780 unless otherwise noted. Sweet Spot Mode Enable Sweet Spot Mode ³ 9 9 8 0 4 8 The sweet spot mode is used to determine where the maximum read rate point or sweet spot is located for a specific bar code type. Refer to the IS3480 Installation and User s Guide (MLPN 00-02026) for a complete description of the sweet spot mode. This feature is not available with the MS3580 or the MS3780. CodeGate ( IS3480 / MS3580) * Enable CodeGate Disable CodeGate ³ 1 1 8 7 1 3 ³ 1 1 8 7 0 3 This barcode is not for use with the MS3780. Please see page R5 for CodeGate options specific to the MS3780. Depth of Field * Normal Depth of Field Reduced Depth of Field ³ 1 1 8 7 0 1 ³ 1 1 8 7 1 1 IS3480 / MS3580 / MS3780 R 3

IS3480 / MS3580 / MS3780 R 4 SECTION R IS3480 / MS3580 / MS3780 The following bar codes are specific to the IS3480, MS3580 and the MS3780 unless otherwise noted. IR Activation IR Activation * Disable IR Activation ³ 1 2 3 8 1 7 ³ 1 2 3 8 0 7 TTL RS232 The following bar codes are only valid for the TTL RS232 Quantum series (IS/MS3x80-102). Enable TTL RS232 Disable TTL RS232 ³ 1 2 0 3 1 1 ³ 1 2 0 3 0 1 Invert TTL RxD and TxD Std. TTL RxD and TxD ³ 1 2 0 3 1 2 The TTL RxD and TxD pins idle at 0V ³ 1 2 0 3 0 2 The TTL RxD and TxD pins idle at +5V

SECTION R MS3780 The following bar codes are specific to the MS3780 unless otherwise noted. CodeGate (MS3780) * Enable CodeGate Out-of-Stand, Primary Pattern Active Disable CodeGate Out-of Stand, Primary Pattern Active ³ 1 2 0 4 0 2 ³ 1 2 0 4 1 2 * Enable CodeGate Out-of-Stand, Secondary Pattern Active Disable CodeGate Out-of Stand, Secondary Pattern Active ³ 1 2 0 4 0 1 ³ 1 2 0 4 1 1 * Enable CodeGate In-Stand Disable CodeGate In-Stand ³ 1 1 8 7 0 7 ³ 1 1 8 7 1 7 IS3480 / MS3580 / MS3780 R 5

November 2005 Printed in the USA 00-02407G