HI-SPEED INTERNET USER GUIDE Wireless Modem Router - 2704R 2013-11 VERSION 1-800-360-8555
TABLE OF CONTENTS 1. Installing Your Wireless Modem Router...4 1.1 Hardware Provided...4 1.2 Connecting Your Modem Router ADSL Technology...5 1.3 Connecting Your Modem Router Cable Technology...5 2. Configuring Your Modem Router...6 3. Connecting to a Wireless Network (Wi-Fi)...7 4. Configuring a Mailbox...8 5. Security...9 6. Troubleshooting...12 7. Configuring TCP/IP Protocol...14 8. Contacting us...26 9. Important Information...26 Wireless Modem Router
1. INSTALLING YOUR WIRELESS MODEM ROUTER 1.1 Hardware Provided Item Description 1 1 F@ST2704R Wireless modem router 2 2 Power cord adapter 3 4 3 4 ADSL line cable used to connect your modem router to your telephone line Ethernet cable used to connect your modem router to the Ethernet port of your computer 5 5 Quick Installation Guide 6 7 6 7 Filter/Splitter used to connect one phone set and your modem router to your telephone line* Microfilter used to connect another phone set to your telephone line * Option depending on pack contents requested WIRELESS NETWORK Note: Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental conditions will adversely affect wireless signal range and throughput. 4 Hi-Speed Internet User Guide
1.2 Connecting Your Modem Router ADSL Technology Phone jack Filet/Splitter Phone To ADSL port Connexion du modem routeur sans fil ADSL cable Ethernet cable Computer Important note: If you are plugging in or adding phones, it is very important to have a filter in place with ADSL technology. Phone jack Filter Phone 1.3 Connecting Your Modem Router Cable Technology Power cord Ethernet cable Cable modem Coaxial cable Important note: The Cable modem must be connected in the #4 port of your wireless modem router. Wireless Modem Router 5
2. CONFIGURING YOUR MODEM ROUTER Your modem router comes already preconfigured to allow you to get on the Internet immediately after you have completed step 1. The purpose of this section is to tell you how you can access the modem router to make various changes, such as security-related ones in Section 5. Follow these steps to change the configuration of your modem router: 1- Start your Internet browser and type in the following address: http://192.168.1.1/ or http://myrouter/ The setup wizard will appear and guide you through the setup process. 2- Enter Username and Password. You will find this information on the label below your modem router. The default user name is admin. Example: 6 Hi-Speed Internet User Guide
3- This screen will appear. Description of Icons My Network View the status of users using your modem router. Configuration - Configure the settings of your wireless network. Services Configure the parental and application control options. Management Configure your modem router password and access the Advanced menu for your modem router. Wireless Modem Router 7
3. CONNECTING TO A WIRELESS NETWORK (WI-FI) 1. Before you connect to a wireless network, make sure that: - your cable modem is correctly installed and configured; - your Internet access is working properly when your computer is connected to the router with a physical connection (Ethernet cable); - your computer is equipped with a built-in wireless adapter. - Your wireless adapter is on (if necessary) - On a laptop computer, the wireless adapter is turned off by default. Refer to your computer s user manual for how to turn it (Wi-Fi) on; - you have on hand during the configuration: - The name of your wireless network (SSID) Example: SSID: SAGEMCOM_XXXX. The XXXX portion will consist of various letters and numbers. Important : SSID is not part of the name of your network. - Your encryption key (WPA) Example: WPA: XXXXXXXX. The XXXXXXXX portion will be made up of various letters and numbers that you must type exactly as they appear, making sure to use upper or lower case letters, where indicated. Important : WPA is not part of your encryption key. This information appears on the label underneath your modem router. Example of a label: For the modem corresponding to the above example of a label, the name of the wireless network (SSID) would be SAGEMCOM_190D and the encryption key (WPA) to connect to this wireless network would be 46J9H5DD. If you are not familiar with configuring a wireless network on your computer, visit the Technical Support section of our website : northerntel.ca Follow these steps: Under Internet, select Troubleshooting Tools and Guides, then Connecting to a wireless network (Wi-Fi). 8 Hi-Speed Internet User Guide
4. CONFIGURING A MAILBOX To configure your mailbox, visit the Technical Support section of our website: northerntel.ca Follow these steps: Under Internet, select Troubleshooting Tools and Guides, then Configuring a Mailbox. Wireless Modem Router 9
5. SECURITY Password for your modem router (default) You will find a default username and individual password on the label below your modem router that you will need to access the router. Wireless network (default) Your modem router has been configured with a default network name (SSID). and Your modem router has been configured with a default individual encryption key (WPA). You will find this information on the label below your modem router. You can start using your modem router right away. Security Warning In order to protect your computer systems against unauthorized access, NorthernTel strongly recommends that you change the encryption key. Follow the instructions below to change your password and encryption key. Important: Record the new password and encryption key under Important Information on this guide. If you have to reset your modem router (Reset button on right side), the password and encryption key will be the default ones (on the label below your modem router). To reset your modem router, you absolutely have to maintain pushed the Reset button during a period of 20 seconds. 10 Hi-Speed Internet User Guide
1- Select Configuration 2- Next, select WLAN to configure your encryption key (SSID). 3- Enter your new encryption key in WPA/WAPI passphrase. Make up an encryption key of about 30 characters long. It should be hard to figure out for an external user but easy for you to remember. It is also recommended that you change your network name (SSID) to a more personalized name to avoid confusion with your neighbours modem routers. 4- Click SAVE/APPLY to apply the change. Note: Current users of the wireless network will have to reconnect using the new encryption key. Wireless Modem Router 11
To change the password for your device. This password should be hard for an external user to figure out but easy for you to remember. Select Management Then select Access Control To change your password: Enter your current password (which you will find on the label below your modem router) in the Old Password field. Enter your new password in the New Password field Re-enter your new password in the Confirm Password field. Click Save/Apply to apply the change. Your basic security settings are now configured. 12 Hi-Speed Internet User Guide
6 TROUBLESHOOTING The area at the top indicates the overall status of your modem router. ADSL Green = Good Red = Bad Downstream and Upstream = Your connection speeds Internet Green = Good, you can get on the Internet Red = You cannot get on the Internet LED Status Meaning Power Off Power Off Green Power On Red Router in rescue mode ADSL Green steady ADSL Up Green blinking ADSL Synchronization in progress or Down @ Internet Off Power Off or The Internet account must be configured or Bridge mode Green steady The Internet account is configured Green blinking Tx/Rx traffic Red Invalid or unauthorized Internet account Wireless Modem Router 13
DEL Statut Signification LAN x (1 to 4) Off No link detected on the Ethernet port Green steady Ethernet port has detected a link with 100 Mbps device Green blinking Tx/Rx traffic at 100 Mbps WLAN Off Wi-Fi deactivated Green steady Wi-Fi activated Green blinking Wi-Fi Tx/Rx traffic USB Off No USB connection Green steady USB connection available Green blinking USB connection ready in progress WPS Off WPS deactivated Green steady WPS activated Green blinking WPS activation in progress 14 Hi-Speed Internet User Guide
7. CONFIGURING TCP/IP PROTOCOL The TCP/IP protocol must be installed, as this step enables you to be identified on the Internet. Without this information, you will not be able to access the Internet. It is therefore important that you make sure that the data you enter is accurate. Please refer to the Important Information section of this document. Before configuring the IP address, make sure that the physical components are working properly. The network interface card needs to have been configured and the modem installed in order to do this. 7.1 CONFIGURING IN WINDOWS XP Please note that the following screens may look different on your computer depending on the display settings selected. 1- Click Start -> Settings -> Control Panel. The Network and Dial-up Connections shortcut might appear and, if so, select it and go directly to Step 3. 2 - Double-click Network and Dial-up Connections. A summary of the connections will appear if you have several types of connections. It is not unusual to see an analog modem connection (dial-up connection) and a network connection (Local Area Network). Wireless Modem Router 15
3 - In Network and Dial-up Connections, right-click the Local Area Connection icon and then click Properties. 4 - In Local Area Connection Properties, in the list of components, click once on Internet Protocol (TCP/IP). Then click the Properties button. 16 Hi-Speed Internet User Guide
5 - In Internet Protocol (TCP/IP) Properties, select the options Obtain an IP address automatically and Obtain DNS server address automatically. 6- Click OK. Your configuration is now complete. Please restart your computer to test your Internet connection. If your Internet connection does not work, please check to ensure that you followed the previous steps. If the problem persists, contact Technical Support at 1-800-360-8555. Wireless Modem Router 17
7.2 CONFIGURING IN WINDOWS VISTA Please note that the following screens may look different on your computer depending on the display settings selected. 1- In Start (the Microsoft Windows icon ), click Control Panel. 2- Double-click Network and Sharing Center. 18 Hi-Speed Internet User Guide
3- In the menu on the left, click Manage network connections. 4- Right-click the Local Area Connection icon. Then click Properties. Wireless Modem Router 19
5- Under the Networking tab, select Internet Protocol Version 4 (TCP/IPv4) by clicking on it once. Then click the Properties button. 6- In Internet Protocol (TCP/IPv4) Properties, select the options Obtain an IP address automatically and Obtain DNS server address automatically. 7- Click OK Your configuration is now complete. Please restart your computer to test your Internet connection. If your Internet connection does not work, please check to ensure that you followed the previous steps. If the problem persists, contact Technical Support at 1-800-360-8555. 20 Hi-Speed Internet User Guide
7.3 CONFIGURING IN WINDOWS 7 Please note that the following screens may look different on your computer depending on the display settings selected. 1- Click Start - > Control Panel. 2- In the Control Panel, choose the classic view by clicking on the little downwards pointing arrow next to the Control Panel in the address bar at the top and choose All Control Panel Items. 3- Click Network and Sharing Center. Wireless Modem Router 21
4- Then click Change adapter settings. 5- In Change adapter settings, right-click the Local Area Connection icon and click Properties. 6- In Local Area Connection Properties, select Internet Protocol Version 4 (TCP/IPv4) by double-clicking it. 22 Hi-Speed Internet User Guide
7- In Internet Protocol Version 4 (TCP/IPv4) Properties, select the options Obtain an IP address automatically and Obtain the following DNS servers automatically. 8- Double-click OK to return to the list of network peripherals. Once this data has been entered, your Internet service will work. Your configuration is now complete. Please restart your computer to test your Internet connection. If your Internet connection does not work, please check to ensure that you followed the previous steps. If the problem persists, contact Technical Support at 1-800-360-8555. Wireless Modem Router 23
7.4 CONFIGURING IN WINDOWS 8 Please note that the following screens may look different on your computer depending on the display settings selected. 1- Right-click the bottom left corner of the screen to bring up the menu (or press Ctrl X). Click on Control Panel. 2 In the Control Panel, click on Network and Internet. 24 Hi-Speed Internet User Guide
3- Click Network and Sharing Center. 4- Then click Change adapter settings. Wireless Modem Router 25
5- In Network Connections, right-click the Ethernet icon and click Properties. 6- In Ethernet Properties, select Internet Protocol Version 4 (TCP/IPv4) by double-clicking it. 26 Hi-Speed Internet User Guide
7- In Internet Protocol Version 4 (TCP/IPv4) Properties, select the options Obtain an IP address automatically and Obtain DNS server address automatically. 8- Double-click OK to return to the list of network peripherals. Once this data has been entered, your Internet service will work. Your configuration is now complete. Please restart your computer to test your Internet connection. If your Internet connection does not work, please check to ensure that you followed the previous steps. If the problem persists, contact Technical Support at 1-800-360-8555. Wireless Modem Router 27
8. CONTACTING US Was this guide not able to answer some of your questions? For technical assistance 24/7, call 1-800-360-8555 or visit the Technical Support section of our web site: Residential northerntel.ca/ntl@home/default_techsupport.htm Business northerntel.ca/business 9. IMPORTANT INFORMATION Domain name of your service: ntl.sympatico.ca Outgoing mail server (SMTP): smtp1.ntl.sympatico.ca Incoming mail server (POP3): pop1.ntl.sympatico.ca Username: (Account name) Password: Email address: Settings of your wireless modem router Password (modem router): Name of your wireless network (SSID): Encryption key (WPA): It is your responsibility to keep this information in a secure place for future use. 28 Hi-Speed Internet User Guide
2013-11 Printed on paper that contains 100% recycled post-consumer fibre.