Release Notes for NeoGate TA410/TA810 41.18.0.X ===Firmware Version: V41.18.0.11==== Applicable Model: NeoGate TA410/TA810 Release Date: January 15th, 2015 http://www.yeastar.com1/6
1. New Features 1. Added support for hunting PSTN trunks on TA410/810 when calling from VoIP Server end. 2. Optimization 1. Call logs can be searched by FXO port. 2. Deleted useless feature Alert Settings from TA410/810. 3. Busy Frequency option on FXO port can be set as dual frequency, i.e. 400,200. 4. Batch editing FXO ports are supported, also resetting selected FXO ports to factory settings is available. 3. Bug Fixes 1. Fixed the issue that if a VoIP Server was set as IAX protocol, Enable Register was checked and Authenticating Incoming Call was set to Yes, then IP Port could not work for the FXO ports where the VoIP Server was applied to. 2. Fixed the issue that if a VoIP Server was set as IAX protocol, Enable Register was not checked and Caller ID was configured, then Port IP could not work for the FXO ports where the VoIP Server was applied to. 3. Fixed the issue that some default parameters were wrong on Tone Zone Settings page if the Country/Region was set to Australia, Italy or Panama. 4. New Features (Instruction) 1. Added support for hunting PSTN trunks on TA410/810 when calling from VoIP Server end. An available PSTN trunk will be hunted when calling from VoIP Server end if multiple FXO ports were registered to the same VoIP Server. Notes: Enable Register should not be checked on the selected VoIP Server Template, meaning end-to-end Connectivity. The same Dial Pattern Template should be selected for the FXO ports. http://www.yeastar.com2/6
===Firmware Version: V41.18.0.8==== Applicable Model: NeoGate TA410/TA810 Release Date: November 25th, 2014 1. Bug Fixes 1. Fixed the issue that the Digit Volume setting on DTMF Settings page could not be saved. 2. Fixed the issue that a hotline number was set on FXO port Port IP Settings page, if you edited the FXO port again, enabled the Simple Mode and saved the changes, the Dial Pattern settings for this FXO port could not work properly. 2.Optimization 1. When there is no PSTN line connected to NeoGate TA s FXO port, the FXO LED will blink slowly.previously, the LED would show a solid green light. http://www.yeastar.com3/6
===Firmware Version: V41.18.0.6==== Applicable Model: NeoGate TA410/TA810 Release Date: October 27th, 2014 1. New Features 1. Added Random SIP Port feature. 2. Added Jitter Buffer option to better the call quality. 3. Added Authenticating Incoming Call option on VoIP Server Settings page. 2. Bug Fixes 1. Fixed the issue that there system would reboot automatically without prompting when upgrading firmware using a wrong firmware file. 2. Fixed the issue that you need to reboot the device twice to make the Country/Region setting on Tone Zone Settings page to take effect. 3. Fixed the issue that when hotline was set on FXO port Port IP Settings page, a caller called in TA but did not get answered, the system would call the destination number again automatically after the caller hang up the call. 4. Fixed the issue inbound call to NeoGate TA would fail if Inbound Caller Pattern was set on FXO port Port IP Settings page. 5. Fixed the issue that the Call Back setting on FXO port Port IP Settings page could not take effect. 6. Fixed the issue that a wrong call back number would be displayed when Call Back was enabled on FXO port IP Port Settings page. 7. Fixed the issue that the Communication Type was not marked as Call Back on Call Log page if a call back was successfully made on NeoGate TA. 3. Instruction (New Features) 1. Added Random SIP Port feature. Path:Gateway VoIP Settings SIP Settings If the option is enabled, the default SIP port will be changed automatically once the system boots up. The system will update the SIP port at a configured time. http://www.yeastar.com4/6
2. Added Jitter Buffer option to better the call quality. Path:Gateway Gateway Settings General Preference When the network is not good, enabling this option will improve the call quality. 3. Added Authenticating Incoming Call option on VoIP Server Settings page. Path:Gateway VoIP Settings VoIP Server When an incoming call reaches TA device and send INVITE packet to TA, TA responds 401, but the Realm info in 401 Response does not match the Realm set on TA VoIP Server, the provider will refuse to authenticate. If you set this option to No, TA will not reply a 401 Response to the provider to authenticate the incoming call. http://www.yeastar.com5/6
[End] http://www.yeastar.com6/6