Internet Telephony PBX System

Transcription

1 Internet Telephony PBX System T1/E1 Gateway With IP PBX Application Copyright PLANET Technology Corporation. All rights reserved.

2 Case 35: With IP PBX Application Head Office E1 PABX interconnect with VIP-2100 to establish VoIP capability, The subscribers in Head Office could communicate with Analog Phone that belong VIP-1680FS in Branch1 and Branch2 by VoIP application. 2 / 26

3 IP PBX Configuration: WAN port 1 Select the [ Network Setup -> > WAN & LAN Setup ] of IP PBX to set up the WAN interface Setup the WAN interface of IP PBX follow the information of IP that provides by ISP WAN Port IP : Static IP IP Address : Subnet Mask : Default Gateway : / 26

4 IP PBX Configuration: SIP Extension 3 Select the [IP[ PBX Setup -> > SIP Extension] to set up the SIP Extensions 4 Add extension numbers for IPX-1900 and IP Phone 4 / 26

5 IP PBX Configuration: Gateway Trunk 5 Select the [Trunk[ Management -> > Gateway Trunk] ] to set up the Gateway Trunk 6 Add an Gateway Trunk for VIP-2100 IP: Port : / 26

6 IP PBX Configuration: Trunk Group 7 Select the [Trunk[ Management -> > Trunk Group] ] to set up the Trunk Group 8 Add an Trunk Group for E1 trunk prefix number Group Name: VIP-2100 Number: 0 Trunk Group: : / 26

7 IP PBX Configuration: Attendant Number 9 Select the [Attendant[ Management -> Attendant Number] ] to set up the Attendant number Attendant Number / 26

8 IP PBX Configuration: Save & Reboot 11 Select the [Save[ & Logout] ] to save configuration and reboot IP PBX / 26

9 13 E1 Gateway Configuration: Signal port Select the [ Control -> > Network ] of E1 Gateway Setup the Signal port interface follow the information of IP that provides by ISP IP Address : IP Netmask : IP Gateway : / 26

10 15 E1 Gateway Configuration: Voice port Select the [ Configuration -> > Interface ] of E1 Gateway 16 Select Interface 17 Then press [ Modify ] button 10 / 26

11 E1 Gateway Configuration: Voice port 18 Setup the Voice port interface follow the information of IP that provides by ISP Interface Type : 1 E1/T1 (According practical E1/T1 port number) Description : VoIP 1E1/T1 Interface (For references) IP Address : Subnet Mask : Default Gateway : PCM Type : A-law (Depend on practical E1/T1 line) 11 / 26

12 E1 Gateway Configuration: Trunk Press [ Detail ] button Press [ Modify ] button 12 / 26

13 E1 Gateway Configuration: Trunk 21 Setup Trunk interface follow the information that provides by ISP. 13 / 26

14 E1 Gateway Configuration: SIP Settings 22 Select the [Configuration[ -> > SIP] ] of E1 Gateway to setup SIP setting for registering to IP PBX. 24 Press [ Modify ] button to setup the related SIP configuration After setup completed, press [ Apply ] button save settings 26 Then press [ Proxy ] to setup registration configuration 14 / 26

15 E1 Gateway Configuration: SIP Settings 27 Press [ ID 0 ] field Then press [ Modify ] to setup registration configuration / 26

16 E1 Gateway Configuration: SIP Settings 29 Press [ Active ] mode and setup the related SIP configuration 30 After setup completed, press [ Apply ] button save settings 16 / 26

17 E1 Gateway Configuration: SIP Settings 31 To check E1 Gateway if registered to IP PBX successfully 17 / 26

18 E1 Gateway Configuration: VoIP Hunting Select the [Configuration[ -> > Digit Manipulation] of E1 Gateway to add the Dialplan Number Press [ New ] to add Group ID 0 & 1 18 / 26

19 E1 Gateway Configuration: Dial Plan 34 Press [ Detail ] to setup Group ID 0-PSTN_Incoming0 Setup Incoming Dial Plan, and assign if called number matched the prefix number, the incoming calls will redirect to specific numbers : The incoming call will redirect to ext : The incoming call will redirect to ext : The incoming call will redirect to ext ~9 : The incoming calls will redirect to AA (Auto Attendant) 19 / 26

20 E1 Gateway Configuration: Dial Plan 35 Press [ Detail ] to setup Group ID 1-PSTN_Mobile1 Setup Outgoing Dial Plan, and assign if the SIP subscribers dial the speed number, the calling number will become complete numbers and call to mobile : If dial 6010, it will call to : If dial 6019, it will call to : If dial 6020, it will call to / 26

21 E1 Gateway Configuration: Call Flow Select the [Control[ -> > Call Flow Editor] ] of E1 Gateway to setup the call flows. 36 Refer to the below call flows to setup / 26

22 E1 Gateway Configuration: Call Flow Refer to each components configuration to setup the call flows <Tips> ANI: Calling number DNIS: Called number 22 / 26

23 E1 Gateway Configuration: Call Flow Refer to each components configuration to setup the call flows 23 / 26

24 E1 Gateway Configuration: Apply & Restart 38 Select the [Configuration[ -> > Apply Change] to effect the new settings. Select the [Control[ -> > System] Select the [Restart[ Restart] ] to reboot E1 Gateway. 24 / 26

25 Dialing Procedures A. T1/E1 Incoming calls Depend on outside PSTN callers call the below numbers of E1/T1 Gateway, the call will transfer to AA or different SIP subscribers directly : This call will transfer to ext.1001 directly : This call will transfer to ext.2001 directly : This call will transfer to ext.2002 directly ~ : These calls will transfer to IVR of IP PBX, the caller will hear prompts for transfer to desired extension after input extension number B. T1/E1 Outgoing calls The SIP subscribers dial the E1/T1 trunk prefix number 0 at first, and hearing a dialtone, then depend on the SIP subscribers if calling the speed dial number : This call will call to : This call will call to : This call will call to : This call will call to NOTE: The mentioned parameters and network settings in this sample be carefully modified to meet the real-world applications. 25 / 26

26