AudioCodes configuration for working with Novataxe. Table of Contents Detecting the AC GW IP address... 2 Default... 2 Using Telephone connected... 2 Using BOOTP... 2 Setting the IP... 3 Using Telephone connected... 3 Using BOOTP... 4 Configuration VoIP... 5 International numbers- Number length... 5 IP of the VoIP operator... 6 Coders... 7 Configuration GW to work with Novataxe... 8 Syslog / CDR report level... 8 SYSLOG & SNMP... 9 Telnet setting... 10 Disable Hook-Flash... 11 Save configuration... 12 Page 1 of 12
Detecting the AC GW IP address Default 1. Default IP address 10.1.10.10 2. Using DHCP Using Telephone connected 1. Connect a telephone to one of the FXS ports. Lift the handset and dial ***12345 (three stars followed by the digits 1, 2, 3, 4, 5). 2. Wait for the 'configuration menu' voice prompt to be played. 3. dial 1# for prompting the IP address. Using BOOTP 1. To detect IP of AudioCodes FXS, launch bootp application supplied with the CD which include in the package. 2. Disable the filter unknown clients and reboot the GW. Page 2 of 12
Setting the IP Using Telephone connected 1. Connect a telephone to one of the FXS ports. Lift the handset and dial ***12345 (three stars followed by the digits 1, 2, 3, 4, 5). 2. Wait for the 'configuration menu' voice prompt to be played. 3. To change the IP address, press 1 followed by the pound key (#). The current IP address of the gateway is played. Press # to change it. Dial the new IP address; use the star (*) key instead of dots ("."), e.g. 192*168*0*4 and press # to finish. Review the new IP address, and press 1 to save it. 4. To change the subnet mask, press 2 followed by the # key. The current subnet mask of the gateway is played. Press # to change it. Dial the new subnet mask; e.g. 255*255*0*0 and press # to finish. Review the new subnet mask, and press 1 to save it. 5. To change the default gateway IP address, press 3 followed by the # key. The current default gateway address of the gateway is played. Press # to change it. Dial the new default gateway address; e.g. 192*168*0*1 and press # to finish. Review the new default gateway address, and press 1 to save it. 6. Hang up the handset. Access the gateway's Embedded Web Server with the new IP address you assigned (refer to Section 3.3 on page 23). 7. Reset the gateway. Click the Reset Device button on the main menu bar; the Reset screen is displayed. Click the button Reset (with the Burn option selected). Page 3 of 12
Using BOOTP 1. Use BOOTP dialog box to set the IP Page 4 of 12
Configuration VoIP Configuration the gateway to work with the VoIP operator. Successful setting, will enable to make calls and voice pass both directions. International numbers- Number length and End dialing To enable international numbers, select Configuration/Protocol Configuration/Protocol definition/dtmf & Dialing, select Advanced Parameter List and change the max digits to 20 Add the pattern for end automatically the dialling, 0[1-689]xxxxxxxx 00xxxxxxx.T on Digit Mapping Rules. Page 5 of 12
IP of the VoIP operator Set the IP of the VoIP operator to terminate the calls: select Configuration/Protocol Configuration/Routing Tables/Tel to IP routing Page 6 of 12
Coders Make sure that the CODECs selected compatible with VoIP providers, select Configuration/Protocol Configuration/Protocol definition/coders and select the CODECS required. Page 7 of 12
Configuration GW to work with Novataxe Syslog / CDR report level La Connectivité de Qualité en Toute Simplicité Select Configuration / Protocol Configuration / SIP Advanced Parameters / Advanced Parameters CDR Report Level = Start & End Call Debug Level = 2 Page 8 of 12
SYSLOG & SNMP Select Management/ Management Configuration/ Management Setting Syslog Server IP Address = IP of the PC with NOVATAXE Enable Syslog = Enable Disable SNMP= No Page 9 of 12
Telnet setting Select Configuration / Network Setting / Application Setting Telnet setting:! Embedded Telnet Server = Enable (Unsecured) Page 10 of 12
Disable Hook-Flash Hook-flash can cause a call to be not invoiced, to prevent this all the reasons for hookflash, should be disabled, as in the enclosed picture. Select Configuration / Protocol Configuration / SIP Advanced Parameters / Supplementary Services and DISABLE: 1. Enable hold - Disable 2. Enable Transfer Disable 3. Enable Call Forward - Disable Page 11 of 12
Save configuration Do not forget to save configuration before exit, otherwise all changes will be lost on next reboot. Select button BURN to save the configuration. Page 12 of 12